KBP 3 005 thru KBP 3 10 3.0 A Single-Phase GPP Bridge Rectifier Rectifier Reverse Voltage 50 to 1000V 14.7+ 0.5 11.2 + 0.5 Features This series is UL listed under the Recognized Component Index, file number E142814 Ideal for printed circuit board mounting The plastic material used carries Underwriters Laboratory flammability recognition 94V-0 Built-in printed circuit board stand-offs High case dielectric strength High temperature soldering guaranteed 265 /10 seconds at 5 lbs (2.3kg) tension 12.2 + 0.5 12.7 MIN. 15.2 MIN. 3.85 + 0.25 Mechanical Data 0.81+ 0.05 Case: Reliable low cost construction utilizing molded plastic technique Terminals: Plated leads solderable per MIL-STD-202, Method 208 Mounting Position: Any Weight: 0.065 ounce, 2.2 grams (approx) 1.5 + 0.2 2.41+ 0.25 4.83 + 0.25 Dimensions in millimeters(1mm =0.0394＂） Maximum Ratings & Thermal Characteristics Rating at 25 C ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz. For Capacitive load derate current by 20%. KBP KBP KBP KBP KBP KBP Parameter Symbol 3005 308 301 302 304 306 VRRM 200 400 800 Maximum repetitive peak reverse voltage 50 600 100 Maximum RMS bridge input voltage Maximum DC blocking voltage Maximum average forward rectified output current at TA=50 C VRMS VDC 35 50 70 140 280 100 200 400 KBP 310 unit 1000 V 420 560 700 V 600 800 1000 V IF(AV) 3.0 A Peak forward surge current single sine-wave IFSM superimposed on rated load (JEDEC Method) 60 A I t 2 15.0 A sec ReJA 10.0 Rating for fusing ( t<8.3ms) Typical thermal resistance per element (1) Typical junction capacitance per element (2) Cj 25.0 Operating junction and storage temperature range TJ, TSTG -55 to + 150 2 C/W pF Electrical Characteristics Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz. For Capacitive load derate by 20 %. KBP KBP KBP KBP KBP KBP Parameter Symbol 3 308 301 302 304 306 005 Maximum instantaneous forward voltage drop 1.1 VF per leg at 2.0A Maximum DC reverse current at rated TA =25 C DC blocking voltage per element TA =125 C IR Notes: (1)Thermal resistance from Junction to Ambemt on P.C.board mounting. (2)Measured at 2.0MHz and applied reverse voltage of 4.0 volts. ｗｗｗ．ａｓｅｍｉ．ｔｗ 10 500 KBP 310 Unit V A o Rating and Characteristic Curves ( TA=25 C Unless otherwise noted ) KBP3005 thru KBP310 Fig. 2 Maximum Non-repetitive Peak Forward Surge Current Average Forward Output Current, Amperes 3.0 Lead Case Ambient 1.5 Peak Forward Surge Current, Amperes Fig. 1 Derating Curve for Output Rectified Current 60 8.3ms Single half-sine-Wave [JEDEC Method] 50 40 30 20 10 0 10 1 100 Number of Cycles at 60HZ Fig. 4 Typical Reverse Characteristics 0 10 50 150 100 o Case Temperature, C Instantaneous Reverse Current ,Amperes TA=125 C 10 0.1 TA=25 C .01 Tj=25 C Pulse Width=300us 2% duty cycle 0 20 40 60 80 100 120 Percent of Rated Peak Reverse Voltage, % 1.0 Fig. 5 Typical Junction Capacitance 100 0.1 .01 0.4 0.6 0.8 1.0 1.2 Instantaneous Forward Voltage, Volts 1.4 Capacitance, pF Instantaneous Forward Current, Amperes Fig. 3 Typical Instantaneous Forward Characteristics TA=100 C 1.0 Tj=25 C f=1.0MHz 10 1 10 Reverse Voltage, Volts ｗｗｗ．ａｓｅｍｉ．ｔｗ 100 140