MAXIM DS12885

19-5213; Rev 4; 4/10
Real-Time Clocks
The DS12885, DS12887, and DS12C887 real-time
clocks (RTCs) are designed to be direct replacements
for the DS1285 and DS1287. The devices provide a
real-time clock/calendar, one time-of-day alarm, three
maskable interrupts with a common interrupt output, a
programmable square wave, and 114 bytes of batterybacked static RAM (113 bytes in the DS12C887 and
DS12C887A). The DS12887 integrates a quartz crystal
and lithium energy source into a 24-pin encapsulated
DIP package. The DS12C887 adds a century byte at
address 32h. For all devices, the date at the end of the
month is automatically adjusted for months with fewer
than 31 days, including correction for leap years. The
devices also operate in either 24-hour or
12-hour format with an AM/PM indicator. A precision
temperature-compensated circuit monitors the status of
VCC. If a primary power failure is detected, the device
automatically switches to a backup supply. A lithium
coin-cell battery can be connected to the VBAT input
pin on the DS12885 to maintain time and date operation
when primary power is absent. The device is accessed
through a multiplexed byte-wide interface, which supports both Intel and Motorola modes.
Applications
Embedded Systems
Utility Meters
Features
♦ Drop-In Replacement for IBM AT Computer
Clock/Calendar
♦ RTC Counts Seconds, Minutes, Hours, Day, Date,
Month, and Year with Leap Year Compensation
Through 2099
♦ Binary or BCD Time Representation
♦ 12-Hour or 24-Hour Clock with AM and PM in
12-Hour Mode
♦ Daylight Saving Time Option
♦ Selectable Intel or Motorola Bus Timing
♦ Interfaced with Software as 128 RAM Locations
♦ 14 Bytes of Clock and Control Registers
♦ 114 Bytes of General-Purpose, Battery-Backed
RAM (113 Bytes in the DS12C887 and
DS12C887A)
♦ RAM Clear Function (DS12885, DS12887A, and
DS12C887A)
♦ Interrupt Output with Three Independently
Maskable Interrupt Flags
Security Systems
♦ Time-of-Day Alarm Once Per Second to Once
Per Day
Network Hubs, Bridges, and Routers
♦ Periodic Rates from 122μs to 500ms
Typical Operating Circuit
♦ Programmable Square-Wave Output
CRYSTAL
X1
AS
VCC
X2
VCC
RESET
RCLR
R/W
DS
DS83C520
CS
♦ End-of-Clock Update Cycle Flag
DS12885
♦ Automatic Power-Fail Detect and Switch Circuitry
♦ Optional 28-Pin PLCC Surface Mount Package or
32-Pin TQFP (DS12885)
♦ Optional Encapsulated DIP (EDIP) Package with
Integrated Crystal and Battery (DS12887,
DS12887A, DS12C887, DS12C887A)
AD(0–7)
SQW
♦ Optional Industrial Temperature Range Available
IRQ
VBAT
♦ Underwriters Laboratory (UL) Recognized
MOT
GND
Pin Configurations and Ordering Information appear at end of data sheet.
______________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
General Description
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
ABSOLUTE MAXIMUM RATINGS
Voltage Range on VCC Pin Relative to Ground .....-0.3V to +6.0V
Operating Temperature Range ...................................................
Commercial (noncondensing) .............................0°C to +70°C
Operating Temperature Range ...................................................
Industrial (noncondensing)...............................-40°C to +85°C
Storage Temperature Range
EDIP ..................................................................-40°C to +85°C
PDIP, SO, PLCC, TQFP ..................................-55°C to +125°C
Lead Temperature (soldering, 10s) .................................+260°C
(Note: EDIP is hand or wave-soldered only.)
Soldering Temperature (reflow)
PDIP, SO, PLCC............................................................+260°C
TQFP .............................................................................+245°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +4.5V to +5.5V, TA = over the operating range, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNITS
5.5
V
2.5
4.0
V
V
Supply Voltage
VCC
(Note 3)
4.5
VBAT Input Voltage
VBAT
(Note 3)
Input Logic 1
Input Logic 0
TYP
VIH
(Note 3)
2.2
VCC +
0.3
-0.3
+0.8
V
15
mA
VIL
(Note 3)
VCC Power-Supply Current
ICC1
(Note 4)
VCC Standby Current
ICCS
(Note 5)
mA
Input Leakage
IIL
-1.0
+1.0
µA
I/O Leakage
IOL
(Note 6)
-1.0
+1.0
µA
Input Current
IMOT
(Note 7)
-1.0
+500
µA
Output at 2.4V
IOH
(Note 3)
-1.0
Output at 0.4V
IOL
(Note 3)
Power-Fail Voltage
VPF
(Note 3)
VRT Trip Point
2
VRTTRIP
_____________________________________________________________________
4.0
mA
4.25
1.3
4.0
mA
4.5
V
V
Real-Time Clocks
(VCC = 0V, VBAT = 3.0V, TA = over the operating range, unless otherwise noted.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
VBAT Current (OSC On);
TA = +25°C, VBACKUP = 3.0V
IBAT
(Note 8)
500
nA
VBAT Current (Oscillator Off)
IBATDR
(Note 8)
100
nA
MAX
UNITS
DC
ns
AC ELECTRICAL CHARACTERISTICS
(VCC = 4.5V to 5.5V, TA = over the operating range.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Cycle Time
tCYC
385
Pulse Width, DS Low or R/W High
PWEL
150
ns
Pulse Width, DS High or R/W Low
PWEH
125
ns
Input Rise and Fall
t R , tF
R/W Hold Time
tRWH
10
ns
R/W Setup Time Before DS/E
tRWS
50
ns
Chip-Select Setup Time Before
DS or R/W
tCS
20
ns
Chip-Select Hold Time
tCH
0
ns
Read-Data Hold Time
tDHR
10
Write-Data Hold Time
tDHW
0
ns
Address Valid Time to AS Fall
tASL
30
ns
Address Hold Time to AS Fall
tAHL
10
ns
Delay Time DS/E to AS Rise
tASD
20
ns
PWASH
60
ns
Delay Time, AS to DS/E Rise
tASED
40
ns
Output Data Delay Time from DS
or R/W
tDDR
20
Data Setup Time
tDSW
100
ns
Reset Pulse Width
tRWL
5
µs
IRQ Release from DS
tIRDS
2
µs
IRQ Release from RESET
tIRR
2
µs
Pulse Width AS High
30
80
120
ns
ns
ns
_____________________________________________________________________
3
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
DC ELECTRICAL CHARACTERISTICS
Real-Time Clocks
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Motorola Bus Read/Write Timing
PWASH
tASED
AS
tASD
tCYC
PWEH
PWEL
DS
tRWS
tRWH
R/ W
tCH
tCS
CS
tDSW
tDHW
AD0–AD7
WRITE
tAHL
tASL
tDHR
AD0–AD7
READ
tDDR
Intel Bus Write Timing
tCYC
AS
PWASH
tASD
DS
tASD
tASED
R/W
PWEH
PWEL
tCH
tCS
CS
tASL
tAHL
tDSW
AD0–AD7
WRITE
4
_____________________________________________________________________
tDHW
Real-Time Clocks
tCYC
PWASH
AS
tASD
tASED
DS
PWEH
PWEL
tASD
R/W
tCH
tCS
CS
tASL
tDHR
tDDR
tAHL
AD0–AD7
IRQ Release Delay Timing
DS
RESET
tRWL
IRQ
tIRR
tIRDS
Power-Up/Power-Down Timing
VCC
VPF(MAX)
VPF(MIN)
tF
tR
tRPU
tDR
INPUTS
RECOGNIZED
DON'T CARE
RECOGNIZED
HIGH-Z
OUTPUTS
VALID
VALID
_____________________________________________________________________
5
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Intel Bus Read Timing
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
POWER-UP/POWER-DOWN CHARACTERISTICS
(TA = -40°C to +85°C) (Note 2)
PARAMETER
SYMBOL
Recovery at Power-Up
CONDITIONS
MIN
TYP
MAX
UNITS
200
ms
tRPU
20
VCC Fall Time; VPF(MAX) to
VPF(MIN)
tF
300
µs
VCC Rise Time; VPF(MIN) to
VPF(MAX)
tR
0
µs
DATA RETENTION
(TA = +25°C)
PARAMETER
SYMBOL
Expected Data Retention
CONDITIONS
MIN
tDR
TYP
MAX
10
UNITS
years
CAPACITANCE
(TA = +25°C) (Note 9)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Capacitance on All Input Pins
Except X1 and X2
CIN
5
pF
Capacitance on IRQ, SQW, and
DQ Pins
CIO
7
pF
AC TEST CONDITIONS
PARAMETER
TEST CONDITIONS
Input Pulse Levels
0 to 3.0V
Output Load Including Scope and Jig
50pF + 1TTL Gate
Input and Output Timing Measurement Reference Levels
Input/Output: VIL maximum and VIH minimum
Input-Pulse Rise and Fall Times
5ns
WARNING: Negative undershoots below -0.3V while the part is in battery-backed mode may cause loss of data.
Note 1: RTC modules can be successfully processed through conventional wave-soldering techniques as long as temperature
exposure to the lithium energy source contained within does not exceed +85°C. However, post-solder cleaning with waterwashing techniques is acceptable, provided that ultrasonic vibrations are not used to prevent crystal damage.
Note 2: Limits at -40°C are guaranteed by design and not production tested.
Note 3: All voltages are referenced to ground.
Note 4: All outputs are open.
Note 5: Specified with CS = DS = R/W = RESET = VCC; MOT, AS, AD0–AD7 = 0; VBACKUP open.
Note 6: Applies to the AD0 to AD7 pins, the IRQ pin, and the SQW pin when each is in a high-impedance state.
Note 7: The MOT pin has an internal 20kΩ pulldown.
Note 8: Measured with a 32.768kHz crystal attached to X1 and X2.
Note 9: Guaranteed by design. Not production tested.
Note 10: Measured with a 50pF capacitance load.
6
_____________________________________________________________________
Real-Time Clocks
IBAT1 vs. VBAT
vs. TEMPERATURE
+85°C
300
32768.70
32768.60
FREQUENCY (Hz)
IBAT (nA)
+25°C
250
0°C
+70°C
+40°C
200
3.0
32768.40
32768.30
32768.10
150
2.8
32768.50
32768.20
-40°C
2.5
DS12885 toc02
DS12885 toc01
VCC = 0V
OSCILLATOR FREQUENCY
vs. VCC
3.5
3.3
VBAT (V)
3.8
32768.00
4.0
4.5
4.8
5.0
5.3
5.5
VCC (V)
Functional Diagram
X1
OSC
DIVIDE
BY 8
DIVIDE
BY 64
DIVIDE
BY 64
X2
VCC
GND
16:1 MUX
POWER
CONTROL
VBAT
DS12885
SQUAREWAVE
GENERATOR
SQW
IRQ
GENERATOR
IRQ
CS
R/W
REGISTERS A, B, C, D
DS
AS
MOT
RESET
AD0–AD7
RLCR
BUS
INTERFACE
CLOCK/CALENDAR
UPDATE LOGIC
CLOCK/CALENDAR AND
ALARM REGISTERS
BUFFERED CLOCK/
CALENDAR AND ALARM
REGISTERS
USER RAM
114 BYTES
_____________________________________________________________________
7
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Typical Operating Characteristics
(VCC = +5.0V, TA = +25°C, unless otherwise noted.)
Real-Time Clocks
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Pin Description
PIN
SO,
PDIP
PLCC
TQFP
NAME
FUNCTION
Motorola or Intel Bus Timing Selector. This pin selects one of two bus types. When
connected to VCC, Motorola bus timing is selected. When connected to GND or
left disconnected, Intel bus timing is selected. The pin has an internal pulldown
resistor.
1
1
2
29
MOT
2
—
3
30
X1
3
—
4
31
X2
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator
circuitry is designed for operation with a crystal having a 6pF specified load
capacitance (CL). Pin X1 is the input to the oscillator and can optionally be
connected to an external 32.768kHz oscillator. The output of the internal oscillator,
pin X2, is left unconnected if an external oscillator is connected to pin X1.
4–11
4–11
5–10,
12, 14
1, 2, 3,
5, 7, 8,
9, 11
AD0–
AD7
Multiplexed, Bidirectional Address/Data Bus. The addresses are presented during
the first portion of the bus cycle and latched into the device by the falling edge of
AS. Write data is latched by the falling edge of DS (Motorola timing) or the rising
edge of R/W (Intel timing). In a read cycle, the device outputs data during the
latter portion of DS (DS and R/W high for Motorola timing, DS low and R/W high for
Intel timing). The read cycle is terminated and the bus returns to a highimpedance state as DS transitions low in the case of Motorola timing or as DS
transitions high in the case of Intel timing.
12, 16
12
15, 20
12, 17
GND
Ground
13
14
15
8
EDIP
13
14
15
16
17
19
13
14
16
CS
Active-Low Chip-Select Input. The chip-select signal must be asserted low for a
bus cycle in the device to be accessed. CS must be kept in the active state during
DS and AS for Motorola timing and during DS and R/W for Intel timing. Bus cycles
that take place without asserting CS will latch addresses, but no access occurs.
When VCC is below VPF volts, the device inhibits access by internally disabling the
CS input. This action protects the RTC data and the RAM data during power
outages.
AS
Address Strobe Input. A positive-going address-strobe pulse serves to
demultiplex the bus. The falling edge of AS causes the address to be latched
within the device. The next rising edge that occurs on the AS bus clears the
address regardless of whether CS is asserted. An address strobe must
immediately precede each write or read access. If a write or read is performed
with CS deasserted, another address strobe must be performed prior to a read or
write access with CS asserted.
R/W
Read/Write Input. The R/W pin has two modes of operation. When the MOT pin is
connected to VCC for Motorola timing, R/W is at a level that indicates whether the
current cycle is a read or write. A read cycle is indicated with a high level on R/W
while DS is high. A write cycle is indicated when R/W is low during DS. When the
MOT pin is connected to GND for Intel timing, the R/W signal is an active-low
signal. In this mode, the R/W pin operates in a similar fashion as the write-enable
signal (WE) on generic RAMs. Data are latched on the rising edge of the signal.
_____________________________________________________________________
Real-Time Clocks
PIN
SO,
PDIP
EDIP
PLCC
TQFP
22
2, 3,
16, 20,
21, 22
1, 11,
13, 18,
26
4, 6, 10,
15, 20,
23, 25,
27, 32
17
18
17
18
21
22
18
19
NAME
N.C.
FUNCTION
No Connection. This pin should remain unconnected. Pin 21 is RCLR for the
DS12887A/DS12C887A. On the EDIP, these pins are missing by design.
DS
Data Strobe or Read Input. The DS pin has two modes of operation depending on
the level of the MOT pin. When the MOT pin is connected to VCC, Motorola bus
timing is selected. In this mode, DS is a positive pulse during the latter portion of the
bus cycle and is called data strobe. During read cycles, DS signifies the time that the
device is to drive the bidirectional bus. In write cycles, the trailing edge of DS causes
the device to latch the written data. When the MOT pin is connected to GND, Intel
bus timing is selected. DS identifies the time period when the device drives the bus
with read data. In this mode, the DS pin operates in a similar fashion as the outputenable (OE) signal on a generic RAM.
RESET
Active-Low Reset Input. The RESET pin has no effect on the clock, calendar, or
RAM. On power-up, the RESET pin can be held low for a time to allow the power
supply to stabilize. The amount of time that RESET is held low is dependent on the
application. However, if RESET is used on power-up, the time RESET is low should
exceed 200ms to ensure that the internal timer that controls the device on powerup has timed out. When RESET is low and VCC is above VPF, the following occurs:
A. Periodic interrupt-enable (PIE) bit is cleared to 0.
B. Alarm interrupt-enable (AIE) bit is cleared to 0.
C. Update-ended interrupt-enable (UIE) bit is cleared to 0.
D. Periodic-interrupt flag (PF) bit is cleared to 0.
E. Alarm-interrupt flag (AF) bit is cleared to 0.
F. Update-ended interrupt flag (UF) bit is cleared to 0.
G. Interrupt-request status flag (IRQF) bit is cleared to 0.
H. IRQ pin is in the high-impedance state.
I. The device is not accessible until RESET is returned high.
J. Square-wave output-enable (SQWE) bit is cleared to 0.
In a typical application, RESET can be connected to VCC. This connection allows
the device to go in and out of power fail without affecting any of the control
registers.
_____________________________________________________________________
9
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Pin Description (continued)
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Pin Description (continued)
PIN
SO,
PDIP
19
20
21
10
EDIP
19
—
21
(DS12887A/
DS12C887A)
PLCC
23
24
25
TQFP
21
22
24
NAME
FUNCTION
IRQ
Active-Low Interrupt Request Output. The IRQ pin is an active-low output of the
device that can be used as an interrupt input to a processor. The IRQ output
remains low as long as the status bit causing the interrupt is present and the
corresponding interrupt-enable bit is set. The processor program normally
reads the C register to clear the IRQ pin. The RESET pin also clears pending
interrupts. When no interrupt conditions are present, the IRQ level is in the highimpedance state. Multiple interrupting devices can be connected to an IRQ
bus, provided that they are all open drain. The IRQ pin is an open-drain output
and requires an external pullup resistor to VCC.
VBAT
Connection for a Primary Battery. (DS12885 Only.) Battery voltage must be held
between the minimum and maximum limits for proper operation. If a backup
supply is not supplied, VBAT must be grounded. Connect the battery directly to
the VBAT pin. Diodes in series between the VBAT pin and the battery may
prevent proper operation. UL recognized to ensure against reverse charging
when used with a lithium battery.
RCLR
Active-Low RAM Clear. The RCLR pin is used to clear (set to logic 1) all the
general-purpose RAM, but does not affect the RAM associated with the RTC. To
clear the RAM, RCLR must be forced to an input logic 0 during battery-backup
mode when VCC is not applied. The RCLR function is designed to be used
through a human interface (shorting to ground manually or by a switch) and not
to be driven with external buffers. This pin is internally pulled up. Do not use an
external pullup resistor on this pin.
23
23
27
26
SQW
Square-Wave Output. The SQW pin can output a signal from one of 13 taps
provided by the 15 internal divider stages of the RTC. The frequency of the
SQW pin can be changed by programming Register A, as shown in Table 1.
The SQW signal can be turned on and off using the SQWE bit in Register B. The
SQW signal is not available when VCC is less than VPF.
24
24
28
28
VCC
DC Power Pin for Primary Power Supply. When VCC is applied within normal
limits, the device is fully accessible and data can be written and read. When
VCC is below VPF reads and writes are inhibited.
____________________________________________________________________
Real-Time Clocks
The DS12885 family of RTCs provide 14 bytes of realtime clock/calendar, alarm, and control/status registers
and 114 bytes (113 bytes for DS12C887 and
DS12C887A) of nonvolatile, battery-backed static RAM.
A time-of-day alarm, three maskable interrupts with a
common interrupt output, and a programmable squarewave output are available. The devices also operate in
either 24-hour or 12-hour format with an AM/PM indicator. A precision temperature-compensated circuit monitors the status of VCC. If a primary power-supply failure
is detected, the devices automatically switch to a backup supply. The backup supply input supports a primary
battery, such as lithium coin cell. The devices are
accessed through a multiplexed address/data bus that
supports Intel and Motorola modes.
Table 1. Crystal Specifications*
PARAMETER
SYMBOL
Nominal
Frequency
fO
Series
Resistance
ESR
Load
Capacitance
MIN
TYP
MAX UNITS
32.768
kHz
50
6
CL
kΩ
pF
*The crystal, traces, and crystal input pins should be isolated
from RF generating signals. Refer to Application Note 58:
Crystal Considerations for Dallas Real-Time Clocks for
additional specifications.
Oscillator Circuit
The DS12885 uses an external 32.768kHz crystal. The
oscillator circuit does not require any external resistors
or capacitors to operate. Table 1 specifies several crystal parameters for the external crystal. Figure 1 shows a
functional schematic of the oscillator circuit. An enable
bit in the control register controls the oscillator.
Oscillator startup times are highly dependent upon
crystal characteristics, PC board leakage, and layout.
High ESR and excessive capacitive loads are the major
contributors to long startup times. A circuit using a
crystal with the recommended characteristics and
proper layout usually starts within one second.
An external 32.768kHz oscillator can also drive the
DS12885. In this configuration, the X1 pin is connected
to the external oscillator signal and the X2 pin is left
unconnected.
COUNTDOWN
CHAIN
CL1
CL2
RTC REGISTERS
DS12885
X1
X2
CRYSTAL
Figure 1. Oscillator Circuit Showing Internal Bias Network
____________________________________________________________________
11
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Detailed Description
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Clock Accuracy
The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match
between the capacitive load of the oscillator circuit and
the capacitive load for which the crystal was trimmed.
Additional error is added by crystal frequency drift
caused by temperature shifts. External circuit noise coupled into the oscillator circuit can result in the clock running fast. Figure 2 shows a typical PC board layout for
isolation of the crystal and oscillator from noise. Refer to
Application Note 58: Crystal Considerations with Dallas
Real-Time Clocks for more detailed information.
Clock Accuracy for DS12887, DS12887A,
DS12C887, DS12C887A Only
The encapsulated DIP modules are trimmed at the factory to an accuracy of ±1 minute per month at +25°C.
Power-Down/Power-Up
Considerations
The real-time clock continues to operate, and the RAM,
time, calendar, and alarm memory locations remain
nonvolatile regardless of the VCC input level. VBAT must
remain within the minimum and maximum limits when
VCC is not applied. When VCC is applied and exceeds
VPF (power-fail trip point), the device becomes accessible after tREC—if the oscillator is running and the oscillator countdown chain is not in reset (Register A). This
time allows the system to stablize after power is
applied. If the oscillator is not enabled, the oscillatorenable bit is enabled on power-up, and the device
becomes immediately accessible.
Time, Calendar, and Alarm
Locations
The time and calendar information is obtained by reading the appropriate register bytes. The time, calendar,
and alarm are set or initialized by writing the appropriate register bytes. Invalid time or date entries result in
undefined operation. The contents of the 10 time, calendar, and alarm bytes can be either binary or binarycoded decimal (BCD) format.
The day-of-week register increments at midnight, incrementing from 1 through 7. The day-of-week register is
used by the daylight saving function, so the value 1 is
defined as Sunday. The date at the end of the month is
12
LOCAL GROUND PLANE (TOP LAYER)
X1
CRYSTAL
X2
NOTE: AVOID ROUTING SIGNAL LINES
IN THE CROSSHATCHED AREA
(UPPER LEFT QUADRANT) OF
THE PACKAGE UNLESS THERE IS
A GROUND PLANE BETWEEN THE
SIGNAL LINE AND THE DEVICE PACKAGE.
GND
Figure 2. Layout Example
automatically adjusted for months with fewer than 31
days, including correction for leap years.
Before writing the internal time, calendar, and alarm registers, the SET bit in Register B should be written to logic
1 to prevent updates from occurring while access is
being attempted. In addition to writing the 10 time, calendar, and alarm registers in a selected format (binary or
BCD), the data mode bit (DM) of Register B must be set
to the appropriate logic level. All 10 time, calendar, and
alarm bytes must use the same data mode. The SET bit
in Register B should be cleared after the data mode bit
has been written to allow the RTC to update the time and
calendar bytes. Once initialized, the RTC makes all
updates in the selected mode. The data mode cannot be
changed without reinitializing the 10 data bytes. Tables
2A and 2B show the BCD and binary formats of the time,
calendar, and alarm locations.
The 24-12 bit cannot be changed without reinitializing the
hour locations. When the 12-hour format is selected, the
higher-order bit of the hours byte represents PM when it
is logic 1. The time, calendar, and alarm bytes are always
accessible because they are double-buffered. Once per
second the seven bytes are advanced by one second
and checked for an alarm condition.
If a read of the time and calendar data occurs during
an update, a problem exists where seconds, minutes,
hours, etc., may not correlate. The probability of reading incorrect time and calendar data is low. Several
methods of avoiding any possible incorrect time and
calendar reads are covered later in this text.
____________________________________________________________________
Real-Time Clocks
condition when at logic 1. An alarm is generated each
hour when the don’t-care bits are set in the hours byte.
Similarly, an alarm is generated every minute with
don’t-care codes in the hours and minute alarm bytes.
The don’t-care codes in all three alarm bytes create an
interrupt every second.
All 128 bytes can be directly written or read, except for
the following:
1) Registers C and D are read-only.
2) Bit 7 of register A is read-only.
3) The MSB of the seconds byte is read-only.
Table 2A. Time, Calendar, and Alarm Data Modes—BCD Mode (DM = 0)
ADDRESS
00H
BIT 7
0
01H
0
10 Seconds
Seconds
Seconds Alarm
00–59
02H
0
10 Minutes
Minutes
Minutes
00–59
03H
0
10 Minutes
Minutes
Minutes Alarm
00–59
Hours
Hours
1–12 +AM/PM
00–23
Hours
Hours Alarm
1–12 +AM/PM
00–23
04H
05H
AM/PM
0
AM/PM
0
BIT 6
0
0
0
0
08H
0
0
09H
BIT 3
10 Hours
10 Hours
0
0
07H
0AH
0
0
06H
BIT 5
BIT 4
10 Seconds
10 Hours
10 Hours
0
0
BIT 2
BIT 1
Seconds
0
10 Months
FUNCTION
Seconds
Day
RANGE
00–59
Day
01–07
Date
Date
01–31
Month
Month
01–12
Year
Year
00–99
Control
—
10 Date
0
BIT 0
10 Years
UIP
DV2
DV1
DV0
RS3
RS2
RS1
RS0
0BH
SET
PIE
AIE
UIE
SQWE
DM
24/12
DSE
Control
—
0CH
IRQF
PF
AF
UF
0
0
0
0
Control
—
0DH
VRT
0
0
0
0
0
0
0
Control
—
0EH-31H
X
X
X
X
X
X
X
X
32H
33H-7FH
10 Century
X
X
X
Century
X
X
X
X
X
RAM
—
Century*
00–99
RAM
—
X = Read/Write Bit.
*DS12C887, DS12C887A only. General-purpose RAM on DS12885, DS12887, and DS12887A.
Note: Unless otherwise specified, the state of the registers is not defined when power is first applied. Except for the seconds register, 0 bits in the time and date registers can be written to 1, but may be modified when the clock updates. 0 bits should always be
written to 0 except for alarm mask bits.
____________________________________________________________________
13
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
The three alarm bytes can be used in two ways. First,
when the alarm time is written in the appropriate hours,
minutes, and seconds alarm locations, the alarm interrupt is initiated at the specified time each day, if the
alarm-enable bit is high. In this mode, the “0” bits in the
alarm registers and the corresponding time registers
must always be written to 0 (Table 2A and 2B). Writing
the 0 bits in the alarm and/or time registers to 1 can
result in undefined operation.
The second use condition is to insert a “don’t care”
state in one or more of the three alarm bytes. The don’tcare code is any hexadecimal value from C0 to FF. The
two most significant bits of each byte set the don’t-care
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Table 2B. Time, Calendar, and Alarm Data Modes—Binary Mode (DM = 1)
ADDRESS
00H
BIT 7
0
BIT 6
0
BIT 5
01H
0
0
Seconds
02H
0
0
Minutes
Minutes
00–3B
03H
0
0
Minutes
Minutes Alarm
00–3B
Hours
01–0C +AM/PM
00–17
Hours Alarm
01–0C +AM/PM
00–17
Day
Date
Month
Year
Control
01–07
01–1F
01–0C
00–63
—
AM/PM
04H
BIT 4
BIT 3
BIT 2
Seconds
0
0
FUNCTION
Seconds
RANGE
00–3B
Seconds Alarm
00–3B
Hours
Hours
AM/PM
0
0
0
Hours
Hours
0
06H
07H
08H
09H
0AH
BIT 0
0
0
05H
BIT 1
0
0
0
0
UIP
0
0
0
0
0
0
DV2
DV1
0
0
Date
0
Day
Month
DV0
Year
RS3
RS2
RS1
RS0
0BH
SET
PIE
AIE
UIE
SQWE
DM
24/12
DSE
Control
—
0CH
IRQF
PF
AF
UF
0
0
0
0
Control
—
0DH
VRT
0
0
0
0
0
0
0
Control
—
0EH-31H
X
X
X
X
X
X
X
X
32H
33H-7FH
N/A
X
X
N/A
X
X
X
X
X
X
RAM
—
Century*
—
RAM
—
X = Read/Write Bit.
*DS12C887, DS12C887A only. General-purpose RAM on DS12885, DS12887, and DS12887A.
Note: Unless otherwise specified, the state of the registers is not defined when power is first applied. Except for the seconds register, 0 bits in the time and date registers can be written to 1, but may be modified when the clock updates. 0 bits should always be
written to 0 except for alarm mask bits.
14
____________________________________________________________________
Real-Time Clocks
The real-time clocks have four control registers that are
accessible at all times, even during the update cycle.
Control Register A
MSB
LSB
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
UIP
DV2
DV1
DV0
RS3
RS2
RS1
RS0
Bit 7: Update-In-Progress (UIP). This bit is a status
flag that can be monitored. When the UIP bit is a 1, the
update transfer occurs soon. When UIP is a 0, the
update transfer does not occur for at least 244µs. The
time, calendar, and alarm information in RAM is fully
available for access when the UIP bit is 0. The UIP bit is
read-only and is not affected by RESET. Writing the
SET bit in Register B to a 1 inhibits any update transfer
and clears the UIP status bit.
Bits 6, 5, and 4: DV2, DV1, DV0. These three bits are
used to turn the oscillator on or off and to reset the
countdown chain. A pattern of 010 is the only combination of bits that turn the oscillator on and allow the RTC
to keep time. A pattern of 11x enables the oscillator but
holds the countdown chain in reset. The next update
occurs at 500ms after a pattern of 010 is written to DV0,
DV1, and DV2.
Bits 3 to 0: Rate Selector (RS3, RS2, RS1, RS0).
These four rate-selection bits select one of the 13 taps
on the 15-stage divider or disable the divider output.
The tap selected can be used to generate an output
square wave (SQW pin) and/or a periodic interrupt. The
user can do one of the following:
1) Enable the interrupt with the PIE bit;
2)
3)
Enable the SQW output pin with the SQWE bit;
Enable both at the same time and the same rate;
or
4) Enable neither.
Table 3 lists the periodic interrupt rates and the squarewave frequencies that can be chosen with the RS bits.
These four read/write bits are not affected by RESET.
____________________________________________________________________
15
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Control Registers
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Control Register B
MSB
LSB
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SET
PIE
AIE
UIE
SQWE
DM
24/12
DSE
Bit 7: SET. When the SET bit is 0, the update transfer
functions normally by advancing the counts once per
second. When the SET bit is written to 1, any update
transfer is inhibited, and the program can initialize the
time and calendar bytes without an update occurring in
the midst of initializing. Read cycles can be executed in
a similar manner. SET is a read/write bit and is not
affected by RESET or internal functions of the device.
Bit 6: Periodic Interrupt Enable (PIE). The PIE bit is a
read/write bit that allows the periodic interrupt flag (PF) bit
in Register C to drive the IRQ pin low. When the PIE bit is
set to 1, periodic interrupts are generated by driving the
IRQ pin low at a rate specified by the RS3–RS0 bits of
Register A. A 0 in the PIE bit blocks the IRQ output from
being driven by a periodic interrupt, but the PF bit is still
set at the periodic rate. PIE is not modified by any internal
device functions, but is cleared to 0 on RESET.
Bit 5: Alarm Interrupt Enable (AIE). This bit is a
read/write bit that, when set to 1, permits the alarm flag
(AF) bit in Register C to assert IRQ. An alarm interrupt
occurs for each second that the three time bytes equal
the three alarm bytes, including a don’t-care alarm
code of binary 11XXXXXX. The AF bit does not initiate
the IRQ signal when the AIE bit is set to 0. The internal
functions of the device do not affect the AIE bit, but is
cleared to 0 on RESET.
Bit 4: Update-Ended Interrupt Enable (UIE). This bit is
a read/write bit that enables the update-end flag (UF)
bit in Register C to assert IRQ. The RESET pin going
low or the SET bit going high clears the UIE bit.
The internal functions of the device do not affect the
UIE bit, but is cleared to 0 on RESET.
16
Bit 3: Square-Wave Enable (SQWE). When this bit is
set to 1, a square-wave signal at the frequency set by
the rate-selection bits RS3–RS0 is driven out on the SQW
pin. When the SQWE bit is set to 0, the SQW pin is held
low. SQWE is a read/write bit and is cleared by RESET.
SQWE is low if disabled, and is high impedance when
VCC is below VPF. SQWE is cleared to 0 on RESET.
Bit 2: Data Mode (DM). This bit indicates whether time
and calendar information is in binary or BCD format.
The DM bit is set by the program to the appropriate format and can be read as required. This bit is not modified by internal functions or RESET. A 1 in DM signifies
binary data, while a 0 in DM specifies BCD data.
Bit 1: 24/12. The 24/12 control bit establishes the format of the hours byte. A 1 indicates the 24-hour mode
and a 0 indicates the 12-hour mode. This bit is
read/write and is not affected by internal functions or
RESET.
Bit 0: Daylight Saving Enable (DSE). This bit is a
read/write bit that enables two daylight saving adjustments when DSE is set to 1. On the first Sunday in
April, the time increments from 1:59:59 AM to 3:00:00
AM. On the last Sunday in October when the time first
reaches 1:59:59 AM, it changes to 1:00:00 AM. When
DSE is enabled, the internal logic test for the first/last
Sunday condition at midnight. If the DSE bit is not set
when the test occurs, the daylight saving function does
not operate correctly. These adjustments do not occur
when the DSE bit is 0. This bit is not affected by internal
functions or RESET.
____________________________________________________________________
Real-Time Clocks
MSB
LSB
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
IRQF
PF
AF
UF
0
0
0
0
Bit 7: Interrupt Request Flag (IRQF). This bit is set to
1 when any of the following are true:
PF = PIE = 1
AF = AIE = 1
UF = UIE = 1
Any time the IRQF bit is 1, the IRQ pin is driven low.
This bit can be cleared by reading Register C or with a
RESET.
Bit 6: Periodic Interrupt Flag (PF). This bit is readonly and is set to 1 when an edge is detected on the
selected tap of the divider chain. The RS3 through RS0
bits establish the periodic rate. PF is set to 1 independent of the state of the PIE bit. When both PF and PIE
are 1s, the IRQ signal is active and sets the IRQF bit.
This bit can be cleared by reading Register C or with a
RESET.
Bit 5: Alarm Interrupt Flag (AF). A 1 in the AF bit indicates that the current time has matched the alarm time.
If the AIE bit is also 1, the IRQ pin goes low and a 1
appears in the IRQF bit. This bit can be cleared by
reading Register C or with a RESET.
Bit 5: Update-Ended Interrupt Flag (UF). This bit is
set after each update cycle. When the UIE bit is set to
1, the 1 in UF causes the IRQF bit to be a 1, which
asserts the IRQ pin. This bit can be cleared by reading
Register C or with a RESET.
Bits 3 to 0: Unused. These bits are unused in Register
C. These bits always read 0 and cannot be written.
Control Register D
MSB
BIT 7
VRT
LSB
BIT 6
0
BIT 5
0
BIT 4
0
Bit 7: Valid RAM and Time (VRT). This bit indicates
the condition of the battery connected to the VBAT pin.
This bit is not writeable and should always be 1 when
read. If a 0 is ever present, an exhausted internal lithium energy source is indicated and both the contents of
BIT 3
0
BIT 2
0
BIT 1
0
BIT 0
0
the RTC data and RAM data are questionable. This bit
is unaffected by RESET.
Bits 6 to 0: Unused. The remaining bits of Register D
are not usable. They cannot be written and they always
read 0.
____________________________________________________________________
17
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Control Register C
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Century Register
(DS12C887/DS12C887A Only)
The century register at location 32h is a BCD register
designed to automatically load the BCD value 20 as the
year register changes from 99 to 00. The MSB of this
register is not affected when the load of 20 occurs, and
remains at the value written by the user.
Nonvolatile RAM (NV RAM)
The general-purpose NV RAM bytes are not dedicated
to any special function within the device. They can be
used by the processor program as battery-backed
memory and are fully available during the update cycle.
when reading Register C. Each used flag bit should be
examined when Register C is read to ensure that no
interrupts are lost.
The second flag bit method is used with fully enabled
interrupts. When an interrupt flag bit is set and the corresponding interrupt-enable bit is also set, the IRQ pin is
asserted low. IRQ is asserted as long as at least one of
the three interrupt sources has its flag and enable bits
set. The IRQF bit in Register C is a 1 whenever the IRQ
pin is driven low. Determination that the RTC initiated an
interrupt is accomplished by reading Register C. A logic
1 in bit 7 (IRQF bit) indicates that one or more interrupts
have been initiated by the device. The act of reading
Register C clears all active flag bits and the IRQF bit.
Interrupts
The RTC family includes three separate, fully automatic
sources of interrupt for a processor. The alarm interrupt
can be programmed to occur at rates from once per
second to once per day. The periodic interrupt can be
selected for rates from 500ms to 122µs. The updateended interrupt can be used to indicate to the program
that an update cycle is complete. Each of these independent interrupt conditions is described in greater
detail in other sections of this text.
The processor program can select which interrupts, if
any, are to be used. Three bits in Register B enable the
interrupts. Writing a logic 1 to an interrupt-enable bit
permits that interrupt to be initiated when the event
occurs. A 0 in an interrupt-enable bit prohibits the IRQ
pin from being asserted from that interrupt condition. If
an interrupt flag is already set when an interrupt is
enabled, IRQ is immediately set at an active level,
although the interrupt initiating the event may have
occurred earlier. As a result, there are cases where the
program should clear such earlier initiated interrupts
before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is
set to logic 1 in Register C. These flag bits are set independent of the state of the corresponding enable bit in
Register B. The flag bit can be used in a polling mode
without enabling the corresponding enable bits. The
interrupt flag bit is a status bit that software can interrogate as necessary. When a flag is set, an indication is
given to software that an interrupt event has occurred
since the flag bit was last read; however, care should
be taken when using the flag bits as they are cleared
each time Register C is read. Double latching is included with Register C so that bits that are set remain stable throughout the read cycle. All bits that are set (high)
are cleared when read, and new interrupts that are
pending during the read cycle are held until after the
cycle is completed. One, two, or three bits can be set
18
Oscillator Control Bits
When the DS12887, DS12887A, DS12C887, and
DS12C887A are shipped from the factory, the internal
oscillator is turned off. This prevents the lithium energy
cell from being used until the device is installed in a
system.
A pattern of 010 in bits 4 to 6 of Register A turns the
oscillator on and enables the countdown chain. A pattern of 11x (DV2 = 1, DV1 = 1, DV0 = X) turns the oscillator on, but holds the countdown chain of the oscillator
in reset. All other combinations of bits 4 to 6 keep the
oscillator off.
Square-Wave Output Selection
Thirteen of the 15 divider taps are made available to a 1of-16 multiplexer, as shown in the functional diagram.
The square-wave and periodic-interrupt generators
share the output of the multiplexer. The RS0–RS3 bits in
Register A establish the output frequency of the multiplexer (see Table 1). Once the frequency is selected, the
output of the SQW pin can be turned on and off under
program control with the square-wave enable bit, SQWE.
Periodic Interrupt Selection
The periodic interrupt causes the IRQ pin to go to an
active state from once every 500ms to once every 122µs.
This function is separate from the alarm interrupt, which
can be output from once per second to once per day.
The periodic interrupt rate is selected using the same
Register A bits that select the square-wave frequency
(Table 1). Changing the Register A bits affects the
square-wave frequency and the periodic-interrupt output. However, each function has a separate enable bit in
Register B. The SQWE bit controls the square-wave output. Similarly, the PIE bit in Register B enables the periodic interrupt. The periodic interrupt can be used with
software counters to measure inputs, create output intervals, or await the next needed software function.
____________________________________________________________________
Real-Time Clocks
SELECT BITS
REGISTER A
tPI PERIODIC
INTERRUPT
RATE
SQW OUTPUT
FREQUENCY
RS3
RS2
RS1
RS0
0
0
0
0
None
None
0
0
0
1
3.90625ms
256Hz
0
0
1
0
7.8125ms
128Hz
0
0
1
1
122.070µs
8.192kHz
0
1
0
0
244.141µs
4.096kHz
0
1
0
1
488.281µs
2.048kHz
0
1
1
0
976.5625µs
1.024kHz
0
1
1
1
1.953125ms
512Hz
1
0
0
0
3.90625ms
256Hz
1
0
0
1
7.8125ms
128Hz
1
0
1
0
15.625ms
64Hz
1
0
1
1
31.25ms
32Hz
1
1
0
0
62.5ms
16Hz
1
1
0
1
125ms
8Hz
1
1
1
0
250ms
4Hz
1
1
1
1
500ms
2Hz
Update Cycle
The device executes an update cycle once per second
regardless of the SET bit in Register B. When the SET
bit in Register B is set to 1, the user copy of the doublebuffered time, calendar, and alarm bytes is frozen and
does not update as the time increments. However, the
time countdown chain continues to update the internal
copy of the buffer. This feature allows time to maintain
accuracy independent of reading or writing the time,
calendar, and alarm buffers, and also guarantees that
time and calendar information is consistent. The update
cycle also compares each alarm byte with the corre-
sponding time byte and issues an alarm if a match or if
a don’t-care code is present in all three positions.
There are three methods that can handle RTC access
that avoid any possibility of accessing inconsistent time
and calendar data. The first method uses the updateended interrupt. If enabled, an interrupt occurs after
every update cycle that indicates over 999ms is available to read valid time and date information. If this
interrupt is used, the IRQF bit in Register C should be
cleared before leaving the interrupt routine.
A second method uses the update-in-progress bit (UIP)
in Register A to determine if the update cycle is in
progress. The UIP bit pulses once per second. After
the UIP bit goes high, the update transfer occurs 244µs
later. If a low is read on the UIP bit, the user has at least
244µs before the time/calendar data is changed.
Therefore, the user should avoid interrupt service routines that would cause the time needed to read valid
time/calendar data to exceed 244µs.
The third method uses a periodic interrupt to determine if
an update cycle is in progress. The UIP bit in Register A
is set high between the setting of the PF bit in Register C
(Figure 3). Periodic interrupts that occur at a rate greater
than tBUC allow valid time and date information to be
reached at each occurrence of the periodic interrupt.
The reads should be complete within one (tPI/2 + tBUC)
to ensure that data is not read during the update cycle.
Handling, PC Board Layout,
and Assembly
The EDIP module can be successfully processed
through conventional wave-soldering techniques so long
as temperature exposure to the lithium energy source
does not exceed +85°C. Post-solder cleaning with waterwashing techniques is acceptable, provided that ultrasonic vibration is not used. Such cleaning can damage
the crystal.
1 SECOND
UIP
tBUC
UF
tP1/2
tP1/2
PF
t PI
tBUC = DELAY TIME BEFORE UPDATE
CYCLE = 244μs
Figure 3. UIP and Periodic Interrupt Timing
____________________________________________________________________
19
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Table 3. Periodic Interrupt Rate and
Square-Wave Output Frequency
Real-Time Clocks
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Pin Configurations
TOP VIEW
MOT 1
24 VCC
MOT 1
24 VCC
X1 2
23 SQW
N.C. 2
23 SQW
X2 3
22 N.C.
N.C. 3
22 N.C.
AD0 4
21 RCLR
AD0 4
20 VBAT
AD1 5
21 N.C.
(RCLR)
20 N.C.
19 IRQ
AD2 6
AD3 7
18 RESET
AD3 7
AD4 8
17 DS
AD4 8
AD5 9
16 GND
AD5 9
16 N.C.
AD6 10
15 R/W
AD6 10
15 R/W
AD7 11
14 AS
AD7 11
14 AS
GND 12
13 CS
GND 12
13 CS
AD1 5
AD2 6
DS12885
DS12885S
SO, PDIP
DS12887
DS12887A
DS12C887
DS12C887A
EDIP
RCLR
VBAT
IRQ
RESET
DS
GND
R/W
25
24
23
22
21
20
19
( ) FOR THE DS12887A/DS12C887A.
26
18
N.C.
SQW
27
17
AS
VCC
28
16
CS
15
GND
14
AD7
N.C.
N.C.
1
MOT
2
X1
3
13
N.C.
X2
4
12
AD6
11
N.C.
9
AD5 10
8
7
AD2
AD4
6
AD1
AD3
5
AD0
DS12885Q
PLCC
NOTE: THE DS12887A AND DS12C887A CANNOT BE STORED OR SHIPPED IN CONDUCTIVE MATERIAL
THAT WILL GIVE A CONTINUITY PATH BETWEEN THE RAM CLEAR PIN AND GROUND.
20
____________________________________________________________________
19 IRQ
18 RESET
17 DS
Real-Time Clocks
PART
TEMP RANGE
PIN-PACKAGE
DS12885+
0°C to +70°C
24 PDIP
DS12885N+
-40°C to +85°C
24 PDIP
DS12885
DS12885Q+
0°C to +70°C
28 PLCC
DS12885Q
DS12885QN+
DS12885Q+T&R
DS12885QN+T&R
DS12885S+
TOP MARK*
DS12885
-40°C to +85°C
28 PLCC
DS12885Q
0°C to +70°C
28 PLCC
DS12885Q
-40°C to +85°C
28 PLCC
DS12885Q
0°C to +70°C
24 SO (300 mils)
DS12885S
-40°C to +85°C
24 SO (300 mils)
DS12885S
DS12885S+T&R
0°C to +70°C
24 SO (300 mils)
DS12885S
DS12885T+
0°C to +70°C
32 TQFP
DS12885
-40°C to +85°C
32 TQFP
DS12885
DS12887+
0°C to +70°C
24 EDIP
DS12887
DS12887A+
0°C to +70°C
24 EDIP
DS12887A
DS12C887+
0°C to +70°C
24 EDIP
DS12C887
DS12C887A+
0°C to +70°C
24 EDIP
DS12C887AA
DS12885SN+
DS12885TN+
+Denotes a lead(Pb)-free/RoHS-compliant package.
T&R = Tape and reel.
*A “+” anywhere on the top mark indicates a lead(Pb)-free device, and an “N” indicates an industrial temperature range device.
Pin Configurations (continued)
AD0
N.C.
X2
X1
MOT
VCC
N.C.
SQW
N.C.
TOP VIEW
32
31
30
29
28
27
26
25
1
Thermal Information
PACKAGE
THETA-JA (°C/W)
THETA-JC (°C/W)
PDIP
75
30
SO
105
22
PLCC
95
25
Package Information
24 RCLR
AD1
2
23 N.C.
AD2
3
22 VBAT
N.C.
4
21 IRQ
DS12885T
20 N.C.
AD3
5
N.C.
6
19 RESET
AD4
7
18 DS
AD5
8
17 GND
TQFP
16
R/W
15
N.C.
14
AS
13
CS
12
GND
11
AD7
10
N.C.
AD6
9
For the latest package outline information and land patterns,
go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package
drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
24 SO
W24+1
21-0042
24 PDIP
P24+4
21-0044
24 EDIP
MDP24+1
21-0241
28 PLCC
Q28+13
21-0049
32 TQFP
C32+3
21-0292
Chip Information
PROCESS: CMOS
SUBSTRATE CONNECTED TO GROUND
____________________________________________________________________
21
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Ordering Information
DS12885/DS12887/DS12887A/DS12C887/DS12C887A
Real-Time Clocks
Revision History
PAGES
CHANGED
REVISION
NUMBER
REVISION
DATE
0
6/05
Initial release of combined data sheet
1
4/06
Corrected the Intel Bus Write Timing, Intel Bus Read Timing, IRQ Release Delay
Timing, Power-Up/Down Timing, and Functional Diagram diagrams; added the
Handling, PC Board Layout, and Assembly section.
2
5/06
Corrected the Intel Bus Write Timing diagram; added PLCC pin description
information; changed pin 16 from N.C. to GND for the SO and PDIP packages.
4, 8, 9, 10, 20
3
2/07
Corrected the Intel Bus Write Timing diagram; updated the Ordering Information;
added the Package Information table; removed the package drawings.
4, 20, 22–27
4
4/10
Updated the storage temperature ranges, added the lead temperature, and updated
the soldering temperature for all packages in the Absolute Maximum Ratings;
removed leaded parts from the Ordering Information table.
DESCRIPTION
—
4, 5, 7, 20
2, 21
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
22 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2010 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
is a registered trademark of Maxim Integrated Products, Inc.
Quijano