MOTOROLA MMC2080VF001

Semiconductor Products Sector
MMC2080/2075/D
Rev. 0, 10/1999
MMC2080/2075
Advance Information
MMC2080/2075 Integrated Processor with
Roaming FLEX™ Decoder
Part 1 Introduction
The MMC2080/2075 is designed to provide the messaging and paging marketplace with a powerful and
flexible solution to carry communications design into the next millennium. The MMC2080 integrates two
of Motorola’s most successful product families, M•CORE™ and the Roaming FLEX™ alphanumeric
decoders, a combination that will set a new standard in the communications industry. Except for the FLEX
decoder, the MMC2075 offers all features of the MMC2080.
Both the The MMC2080/2075 are members of the low-power, high-performance M•CORE family of 32-bit
microcontroller units (MCUs). The M•CORE is a streamlined execution engine that provides many of the
performance enhancements found in mainstream reduced instruction set computers (RISCs). Combining
performance, speed, and cost efficiency in a compact, low-power design, the M•CORE microRISC
architecture is a natural solution for applications where battery life and systems cost are critical design goals.
Given that a total system’s components and processor core determine its power consumption, the instruction
set architecture (ISA) for the M•CORE is designed to optimize the trade-off between performance and total
power consumption. The result is system-wide reduction of total energy consumption with maintenance of
acceptable performance levels. Memory power consumption (both on-chip and external) is a major factor in
system energy consumption. By adopting 16-bit instruction encoding, and thus significantly decreasing the
memory bandwidth needed for a high rate of instruction execution, the MMC2080/2075 minimizes the
overhead of memory system energy consumption.
The MMC2080/2075 also reduces power consumption by coupling a fully static design with dynamic power
management and low-voltage operation. Versatile power management is achieved through automatic power
downs of any internal functional blocks not needed on a clock-by-clock basis. Power conservation modes
are also provided for absolute power conservation.
A table of contents for this document appears on the following page. Figure 1 on page 3 and Figure 2 on
page 4 provide simplified block diagrams of the MMC2080/2075.
This document contains information on a new product. Specifications and information herein
are subject to change without notice.
© Motorola, Inc., 1999. All rights reserved.
Part 1
1.1
1.2
1.3
1.4
1.5
1.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conventions and Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Integrated Roaming FLEX Protocol and the MMC2080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Target Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
5
6
8
8
8
8
Part 2 Signal and Connection Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1
MMC2080/2075 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2
Tables of Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Part 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.1
General Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.2
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Part 4
4.1
4.2
4.3
Pin-out and Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BGA Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PGA Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Ordering Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Part 5 Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.1
Heat Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.2
Electrical Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2
MMC2080/2075 Technical Data
Preliminary
I/O
JTAG
POR
DE
TMS
TCK
TDI
TDO
TRST
XTAL
EXTAL
MPD[7:0]/D[15:8]
CXFC
PLL
OnCE
CPU
UCLK
MPC7/URXD
MPC6/UTXD
MPC5/UCTS
MPC4/URTS
SCI
OSC
INTC
(MPIO)
Timer1
MPC3/TIC1
MPC2/TOC1
Timer0
MPC1/TIC0
MPC0/TOC0
6K RAM
Peripheral Bus
External
Bus
Bridge
System Bus
96K ROM
D[7:0]
A[21:0]
EB[1:0]
BW8
WE
OE
TA
ABORT
BUSCLK
IRQ
SEL[2:0], SEL3
XBOOT
RESET
RSTOUT
SIM
APB
MPIO
SPI1-FSC
Keypad
MPB[7:4]/ROW[3:0]
MPB[3:0]/COL[3:0]
MPA[5:0]
CNFG
FLEX
Melody
BGNT
BREQ
MPE4/LOCK
MPE3/MOSI
MPE2/MISO
MPE1/SS
MPE0/SCLK
LOBAT
EXTS[1:0]
CLKOUT
SYMCLK
S[7:1]
S0/IFIN
Arbiter
SPI0
MLDY
MMC2080 Only
JTAG
I/O
Figure 1. MMC2080/2075 144 Block Diagram (144-Pin Package)
Introduction
Preliminary
3
I/O
JTAG
POR
TC[2:0]
MPD[7:0]/D[15:8]
D[7:0]
D[31:16]
A[21:0]
EB[1:0]
DVLEB[1:0]
BW8
WE
OE
TA
TEA
ABORT
BUSCLK
IRQ
DSTAT[5:0]
DVLMX
SEL[2:0], SEL3
DVLSEL
XBOOT
DVL[1:0]
SHS
OnCE
RESET
RSTOUT
CPU
UCLK
MPC7/URXD
MPC6/UTXD
MPC5/UCTS
MPC4/URTS
SCI
OSC
INTC
(MPIO)
Timer1
MPC3/TIC1
MPC2/TOC1
Timer0
MPC1/TIC0
MPC0/TOC0
96K ROM
External
Bus
Bridge
6K RAM
APB
Peripheral Bus
XTAL
EXTAL
CXFC
SIM
System Bus
DE
TMS
TCK
TDI
TDO
TRST
PLL
MPIO
SPI1-FSC
Keypad
CNFG
FLEX
LOBAT
EXTS[1:0]
CLKOUT
SYMCLK
S[7:1]
S0/IFIN
Arbiter
SPI0
MLDY
HIGHZ
PULL_EN
MPB[7:4]/ROW[3:0]
MPB[3:0]/COL[3:0]
MPA[5:0]
Melody
BGNT
BREQ
MPE4/LOCK
MPE3/MOSI
MPE2/MISO
MPE1/SS
MPE0/SCLK
MMC2080 Only
JTAG
I/O
Figure 2. MMC2080/2075 DVL Block Diagram (208-Pin Package)
4
MMC2080/2075 Technical Data
Preliminary
Conventions and Terminology
1.1 Conventions and Terminology
This document uses the following conventions:
•
OVERBAR is used to indicate a signal that is active when pulled low: for example, RESET.
•
Logic level one is a voltage that corresponds to Boolean true (1) state.
•
Logic level zero is a voltage that corresponds to Boolean false (0) state.
•
To set a bit or bits means to establish logic level one.
•
To clear a bit or bits means to establish logic level zero.
•
A signal is an electronic construct whose state or changes in state convey information.
•
A pin is an external physical connection. The same pin can be used to connect a number of signals.
•
Asserted means that a discrete signal is in active logic state.
— Active low signals change from logic level one to logic level zero.
— Active high signals change from logic level zero to logic level one.
•
Deasserted means that an asserted discrete signal changes logic state.
— Active low signals change from logic level zero to logic level one.
— Active high signals change from logic level on to logic level zero.
•
LSB means least significant bit or bits. MSB means most significant bit or bits. References to low
and high bytes or words are spelled out.
Please refer to the examples in Table 1.
Table 1. Data Conventions
Signal/Symbol
Logic State
Signal State
Voltage
PIN
True
Asserted
VIL/VOL
PIN
False
Deasserted
VIH/VOH
PIN
True
Asserted
VIH/VOH
PIN
False
Deasserted
VIL/VOL
Introduction
Preliminary
5
Features
1.2 Features
The MMC2080/2075 offers the following suite of features.
•
M•CORE™ RISC Processor
— 32-bit load/store M•CORE RISC architecture
— Fixed 16-bit instruction length
— 16-entry 32-bit general-purpose register file
— 32-bit internal address and data buses
— Efficient, four-stage, fully interlocked execution pipeline
— Single-cycle execution for most instructions; two cycles for branches and memory accesses
— Special branch, byte, and bit manipulation instructions
— Support for byte, halfword, and word memory accesses
— Fast interrupt support via vectoring/auto-vectoring and a 16-entry dedicated alternate register
file
•
Integrated Roaming FLEX alphanumeric decoder (MMC2080 only)
— FLEX paging protocol signal processor
— 1600, 3200, and 6400 bits per second (bps) decoding
— Highly programmable receiver control
— FLEX message fragmentation and group messaging support
— SSID and NID roaming support
— Internal demodulator and data slicer
— Improved battery savings via partial address correlation and intermittent receiver clock
— Full support for revision G1.9 of the FLEX protocol
— External CAP code access through parallel or serial FLASH/PROM
•
On-chip memory
— 24 K × 32 CPU ROM (96 K)
— 1.5 K × 32 CPU RAM (6 K)
•
On-chip peripherals
— Asynchronous serial communications interface (SCI) with IrDA capability
— Synchronous serial peripheral interface (SPI)
— Frequency synthesizer controller (FSC)
— Melody generator
— 4 × 4 keypad interface
— Multipurpose I/O ports (MPIO)
— Two 16-bit general purpose timers
— Time-of-day (TOD) timer
— Watchdog timer
— Vectored interrupt controller with 16 programmable priority levels
6
MMC2080/2075 Technical Data
Preliminary
Features
— Oscillator and PLL with software selectable speeds
— AMBA peripheral bridge depipelines system bus for simpler peripheral bus
— 8/16-bit external system bus with 22-bit address bus
•
Operating features
— Processor operation to 10 MHz over full operating range
— Low-power modes
— OnCE™ (On-Chip Emulation) debug module
— Voltage range 1.8 V to 3.6 V; temperature range -20 °C to 85 °C
— Chip-select outputs for four external devices (4 Mbyte per chip select, 16 Mbyte directly
addressable)
— Programmable wait states for external accesses
— External boot option
— External bus interface that accepts internal, half-word, and byte transfers
— External device that may become system bus master
•
Development tools
— Development option (different package) that adds select to bypass internal ROM
— Development option (different package) that extends external bus to 32 bits
— External bus that can display internal transfers
Introduction
Preliminary
7
Integrated Roaming FLEX Protocol and the MMC2080
1.3 Integrated Roaming FLEX Protocol and the MMC2080
The MMC2080 integrates several field-proven technologies, providing a versatile Roaming FLEX solution.
The MMC2080 operates the integrated FLEX decoder in an efficient power-consumption mode, allowing
the CPU to operate in a low-power mode when monitoring for message information. The Roaming FLEX
protocol is a multichannel, high-performance protocol that leading service providers worldwide have
adopted as a de facto standard for roaming paging. Roaming FLEX protocol gives service providers
increased capacity, added reliability, enhanced pager battery performance, and the ability to control a PLLsynthesized receiver and to receive paging messages from a list of paging channels. Finally, the MMC2080
gives the service provider an upward migration path that is completely transparent to the end user.
1.4 Target Applications
The MMC2080/2075 is intended for use in wireless and paging applications. The MMC2080 is designed
for applications needing an M•CORE CPU coupled with a roaming FLEX Decoder. The MMC2075 is
intended for applications requiring the processing power and flexibility of the M•CORE CPU.
1.5 Product Documentation
The three documents listed in Table 2 are required for a complete description of the MMC2080/2075 and
are necessary to design properly with the part. Documentation is available from a local Motorola distributor,
a Motorola Semiconductor Products Sector sales office, a Motorola Literature Distribution Center, or the
World Wide Web. See the last page of this document for contact information.
Table 2. MMC2080/2075 Documentation
Document Name
Description of Contents
Order Number
M•CORE Reference Manual
Detailed description of the M•CORE MCU and
instruction set
MCORERM/AD
MMC2080/2075 User’s Manual
Detailed description of the MMC2080/2075 memory,
peripherals, and interfaces
MMC2080/2075UM/D
MMC2080/2075 Technical Data
MMC2080/2075 pin and package descriptions;
electrical and timing specifications
MMC2080/2075/D
1.6 Ordering Information
Table 3 lists the information you need to supply when placing an order. Consult a Motorola Semiconductor
Products Sector sales office or authorized distributor to determine availability and to order parts.
Table 3. MMC2080/2075 Ordering Information
8
Part
Supply
Voltage
MMC2080
3V
12 mm x 12 mm MAP BGA
144
MMC2080VF001
MMC2075
3V
12 mm x 12 mm MAP BGA
144
MMC2075VF001
MMC2080
3V
43 mm x 43 mm Ceramic PGA
208
Contact Factory
MMC2075
3V
43 mm x 43 mm Ceramic PGA
208
Package Type
MMC2080/2075 Technical Data
Preliminary
Pin
Count
Order Number
Development Use Only
MMC2080/2075 Pin Descriptions
Part 2 Signal and Connection Descriptions
The pins and signals of the MMC2080/2075 are described in the following sections. Figure 3 on page 10
and Figure 4 on page 11 are top and bottom views, respectively, of the 12 mm x 12 mm MAP Ball Grid
Array (BGA) package, and Figure 5 on page 12 and Figure 6 on page 13 are top and bottom views,
respectively, of the 43 mm x 43 mm ceramic Pin Grid Array (PGA) package, showing the pin-outs. Table 4
on page 14 and Table 5 on page 17 list the pins by number and signal name.
Figure 7 on page 21 is a representational pin-out of the chip, grouping the signals by their function. Table 6
on page 20 identifies the number of signals for each group and refers to Table 8 on page 23 through Table 20
on page 27, which are organized according to signal type and give a brief description of each signal pin.
2.1 MMC2080/2075 Pin Descriptions
The following section provides information about the available packages for this product, including
diagrams of the package pin-outs and tables describing how the signals of the MMC2080/2075 are allocated.
There are two packages for each part:
•
The 144-pin I/O, STD small ball (SMBALL) mold array process (MAP) ball grid array (BGA),
12 mm x 12 mm package. Table 4 on page 14 identifies the signal associated with each pin.
•
The 208-pin I/O, PGA, 43 mm x 43 mm ceramic package. Table 5 on page 17 identifies the signal
associated with each pin.
Signal and Connection Descriptions
Preliminary
9
MMC2080/2075 Pin Descriptions
1
2
3
4
5
6
7
8
9
10
11
12
A
VSS
I/O
MPB5/
ROW1
EB1
MPB2/
COL2
MPB0/
COL0
VDD
I/O
SEL1
VSS
I/O
VSS
Core
S2*
B
MPB7/
ROW3
MPB6/
ROW2
BW8
ABORT
EB0
VDD
Core
SEL0
S7*
S4*
S1*
VSS
I/O
MLDY
EXTS1*
C
IRQ
MPA0
MPB4/
ROW0
MPB3/
COL3
MPB1/
COL1
TA
SEL2
S6*
S3*
SYMCLK
EXTS0*
VDD
I/O
VSS
I/O
D
VDD
Core
D0
MPA1
VSS
Core
OE
WE
SEL3
S5*
XBOOT
S0/IFIN
MPE4/
LOCK
VDD
Core
MPE3/
MOSI
E
BUSCLK
VSS
I/O
D2
D1
VDD
OSC
EXTAL
XTAL
VSS
OSC
F
VDD
I/O
MPA3
MPA2
VDD
I/O
VDD
PLL
CXFC
VSS
PLL
A21
G
MPA5
MPA4
D3
D4
A20
A19
A18
VSS
Core
H
VSS
I/O
D8
D9
VDD
I/O
A16
A17
VDD
I/O
BREQ
J
VSS
Core
D5
D10
BGNT
MPE1/
SS
MPE2/
MISO
VSS
I/O
A15
K
D11
D12
VDD
Core
TDI
A1
MPC0/
TOC0
MPC5/
UCTS
VDD
Core
A8
A12
MPE0/
SCLK
A13
A14
L
D6
D7
D13
TDO
VSS
Core
MPC3/
TIC1
A5
MPC6/
UTXD
VDD
I/O
A10
VSS
I/O
VDD
I/O
A11
M
D14
D15
VSS
I/O
TRST
A2
MPC2/
TOC1
A3
MPC7/
URXD
A7
TEST
RSTOUT
VDD
I/O
UCLK
N
VDD
I/O
TCK
TMS
A0
MPC1/
TIC0
VSS
I/O
A4
MPC4/
URTS
A6
A9
DE
RESET
VSS
I/O
LOBAT* CLKOUT*
13
VDD
I/O
Top View
* Signal available only in 2080
Figure 3. MMC2080/2075 BGA (144-Pin) Top View
10
MMC2080/2075 Technical Data
Preliminary
MMC2080/2075 Pin Descriptions
13
12
11
10
9
8
7
6
5
4
3
2
1
VDD
I/O
CLKOUT*
LOBAT*
S2 *
VSS
Core
VSS
I/O
SEL1
VDD
I/O
MPB0/
COL0
MPB2/
COL2
EB1
MPB5/
ROW1
VSS
I/O
A
EXTS1*
MLDY
VSS
I/O
S1*
S4*
S7*
SEL0
VDD
Core
EB0
ABORT
BW8
MPB6/
ROW2
MPB7/
ROW3
B
VSS
I/O
VDD
I/O
EXTS0*
SYMCLK
S3*
S6*
SEL2
TA
MPB1/
COL1
MPB3/
COL3
MPB4/
ROW0
MPA0
IRQ
C
MPE3/
MOSI
VDD
Core
MPE4/
LOCK
S0/IFIN
XBOOT
S5*
SEL3
WE
OE
VSS
Core
MPA1
D0
VDD
Core
D
VSS
OSC
XTAL
EXTAL
VDD
OSC
D1
D2
VSS
I/O
BUSCLK
E
A21
VSS
PLL
CXFC
VDD
PLL
VDD
I/O
MPA2
MPA3
VDD
I/O
F
VSS
Core
A18
A19
A20
D4
D3
MPA4
MPA5
G
BREQ
VDD
I/O
A17
A16
VDD
I/O
D9
D8
VSS
I/O
H
A15
VSS
I/O
MPE2/
MISO
MPE1/
SS
BGNT
D10
D5
VSS
Core
J
A14
A13
MPE0/
SCLK
A12
A8
VDD
Core
MPC5/
UCTS
MPC0/
TOC0
A1
TDI
VDD
Core
D12
D11
K
A11
VDD
I/O
VSS
I/O
A10
VDD
I/O
MPC6/
UTXD
A5
MPC3/
TIC1
VSS
Core
TDO
D13
D7
D6
L
UCLK
VDD
I/O
RSTOUT
TEST
A7
MPC7/
URXD
A3
MPC2/
TOC1
A2
TRST
VSS
I/O
D15
D14
M
VSS
I/O
RESET
DE
A9
A6
MPC4/
URTS
A4
VSS
I/O
MPC1/
TIC0
A0
TMS
TCK
VDD
I/O
N
Bottom View
* Signal available only in 2080
Figure 4. MMC2080/2075 BGA (144-Pin) Bottom View
Signal and Connection Descriptions
Preliminary
11
MMC2080/2075 Pin Descriptions
1
2
3
4
5
6
7
8
9
10
11
12
13
A
MPB6/
ROW2
MPB4/
ROW0
BW8
MPB2/
COL2
MPB0/
COL0
TA
DVLEB1
SEL3
SEL1
VSS
I/O
DVLEB0
VSS
Core
S2 *
B
NC
NC
MPB1/
COL1
WE
SEL2
S7*
S5*
S6*
S3*
C
IRQ
NC
NC
NC
D16
ABORT
EB0
VDD
I/O
TEA
XBOOT
S1*
DVL0
D
VDD
Core
MPA1
VSS
I/O
NC
NC
EB1
OE
VDD
Core
SEL0
S4*
E
BUSCLK
D2
MPA0
MPB7/
ROW3
F
D17
MPA2
D0
VSS
Core
G
MPA4
VDD
I/O
VSS
I/O
H
MPA5
D18
J
D4
K
MPB5/ PULL_EN MPB3/
COL3
ROW1
16
17
S0/IFIN DVLMX
NC
MLDY
DVL1
LOBAT*
NC
NC
EXTS0*
VSS
I/O
VDD
I/O
NC
EXTS1* DSTAT4
NC
NC
DSTAT5 DSTAT1
NC
VDD
I/O
SYMCLK DVLSEL CLKOUT*
14
15
VSS
I/O
MPE3/
MOSI
DSTAT3 DSTAT2 DSTAT0
VDD
OSC
D1
MPE4/
LOCK
VDD
Core
TC2
XTAL
VDD
I/O
MPA3
EXTAL
VSS
OSC
CXFC
VDD
PLL
D19
D20
D3
A21
A20
VSS
Core
VSS
PLL
D8
VSS
I/O
D9
D21
A17
A15
BREQ
TC1
L
VDD
I/O
VSS
Core
D10
BGNT
A14
MPE2/
MISO
A18
A19
M
D22
D23
D12
D25
A11
MPE0/
SCLK
A16
VDD
I/O
N
D5
D24
D6
NC
UCLK
VDD
I/O
MPE1/
SS
VSS
I/O
P
D11
D7
NC
NC
TCK
TC0
D26
VSS
Core
A3
MPC6/
UTXD
A8
DE
NC
NC
VSS
I/O
A12
A13
R
VDD
Core
D14
NC
VDD
I/O
VSS
I/O
HIGHZ
D27
A0
MPC2/
TOC1
MPC4/
URTS
A7
TEST
RSTOUT
NC
NC
NC
NC
T
D13
NC
NC
TMS
TDO
A1
MPC1/
TIC0
D28
MPC0/
TOC0
A5
VDD
Core
VDD
I/O
A10
D31
RESET
SHS
NC
U
D15
NC
NC
TDI
TRST
A2
MPC3/
TIC1
VSS
I/O
A4
MPC5/
UCTS
MPC7/
URXD
D29
A6
A9
D30
VSS
I/O
NC
Top View
* Signal available only in 2080
Figure 5. MMC2080/2075 PGA (208-Pin) Top View
12
MMC2080/2075 Technical Data
Preliminary
MMC2080/2075 Pin Descriptions
17
16
MLDY
NC
EXTS0*
NC
13
12
11
10
9
8
7
6
5
4
3
2
1
DVLMX S0/IFIN
S2 *
VSS
Core
DVLEB0
VSS
I/O
SEL1
SEL3
DVLEB1
TA
MPB0/
COL0
MPB2/
COL2
BW8
MPB4/
ROW0
MPB6/
ROW2
A
NC
LOBAT*
DVL1
S3*
S6*
S5*
S7*
SEL2
WE
MPB1/
COL1
NC
NC
B
DSTAT4 EXTS1*
NC
VDD
I/O
VSS
I/O
DVL0
S1*
XBOOT
TEA
VDD
I/O
EB0
ABORT
D16
NC
NC
NC
IRQ
C
DSTAT1 DSTAT5
NC
NC
S4*
SEL0
VDD
Core
OE
EB1
NC
NC
VSS
I/O
MPA1
VDD
Core
D
MPE3/
MOSI
VDD
I/O
NC
MPB7/
ROW3
MPA0
D2
BUSCLK
E
DSTAT0 DSTAT2 DSTAT3
VSS
Core
D0
MPA2
D17
F
VDD
OSC
VSS
I/O
15
14
CLKOUT DVLSEL SYMCLK
*
*
MPB3/ PULL_EN MPB5/
COL3
ROW1
XTAL
TC2
VDD
Core
MPE4/
LOCK
D1
VSS
I/O
VDD
I/O
MPA4
G
VDD
PLL
CXFC
VSS
OSC
EXTAL
MPA3
VDD
I/O
D18
MPA5
H
VSS
PLL
VSS
Core
A20
A21
D3
D20
D19
D4
J
TC1
BREQ
A15
A17
D21
D9
VSS
I/O
D8
K
A19
A18
MPE2/
MISO
A14
BGNT
D10
VSS
Core
VDD
I/O
L
VDD
I/O
A16
MPE0/
SCLK
A11
D25
D12
D23
D22
M
VSS
I/O
MPE1/
SS
VDD
I/O
UCLK
NC
D6
D24
D5
N
A13
A12
VSS
I/O
NC
NC
DE
A8
MPC6/
UTXD
A3
VSS
Core
D26
TC0
TCK
NC
NC
D7
D11
P
NC
NC
NC
NC
RSTOUT
TEST
A7
MPC4/
URTS
MPC2/
TOC1
A0
D27
HIGHZ
VSS
I/O
VDD
I/O
NC
D14
VDD
Core
R
NC
SHS
RESET
D31
A10
VDD
I/O
VDD
Core
A5
MPC0/
TOC0
D28
MPC1/
TIC0
A1
TDO
TMS
NC
NC
D13
T
NC
VSS
I/O
D30
A9
A6
D29
MPC7/
URXD
MPC5/
UCTS
A4
VSS
I/O
MPC3/
TIC1
A2
TRST
TDI
NC
NC
D15
U
Bottom View
* Signal available only in 2080
Figure 6. MMC2080/2075 PGA (208-Pin) Bottom View
Signal and Connection Descriptions
Preliminary
13
MMC2080/2075 Pin Descriptions
Table 4. MMC2080/2075 BGA (144-Pin) Signal ID by Pin Number (Sheet 1 of 3)
Pin Number
14
Signal Name
Pin Number
Signal Name
A1
Vss I/O
G10
A20
A2
MPB5/ROW1
G11
A19
A3
BW8
G12
A18
A4
MPB2/COL2
G13
Vss Core
A5
MPB0/COL0
H1
Vss I/O
A6
Vdd I/O
H2
D8
A7
SEL1
H3
D9
A8
Vss I/O
H4
Vdd I/O
A9
Vss Core
H10
A16
A10
S2 (2080 Only)
H11
A17
A11
LOBAT (2080 Only)
H12
Vdd I/O
A12
CLKOUT (2080 Only)
H13
BREQ
A13
Vdd I/O
J1
Vss Core
B1
MPB7/ROW3
J2
D5
B2
MPB6/ROW2
J3
D10
B3
BW8
J4
BGNT
B4
ABORT
J10
MPE1/SS
B5
EB0
J11
MPE2/MIS0
B6
Vdd Core
J12
Vss I/O
B7
SEL0
J13
A15
B8
S7 (2080 Only)
K1
D11
B9
S4 (2080 Only)
K2
D12
B10
S1 (2080 Only)
K3
Vdd Core
B11
Vss I/O
K4
TDI
B12
MLDY
K5
A1
B13
EXTS1 (2080 Only)
K6
MPC0/TOC0
C1
IRQ
K7
MPC5/UCTS
C2
MPA0
K8
Vdd Core
MMC2080/2075 Technical Data
Preliminary
MMC2080/2075 Pin Descriptions
Table 4. MMC2080/2075 BGA (144-Pin) Signal ID by Pin Number (Sheet 2 of 3)
Pin Number
Signal Name
Pin Number
Signal Name
C3
MPB4/ROW0
K9
A8
C4
MPB3/COL3
K10
A12
C5
MPB1/COL1
K11
MPE0/SCLK
C6
TA
K12
A13
C7
SEL2
K13
A14
C8
S6 (2080 Only)
L1
D6
C9
S3 (2080 Only)
L2
D7
C10
SYMCLK (2080 Only)
L3
D13
C11
EXTS0 (2080 Only)
L4
TDO
C12
Vdd I/O
L5
Vss Core
C13
Vss I/O
L6
MPC3/TIC1
D1
Vdd Core
L7
A5
D2
D0
L8
MPC6/UTXD
D3
MPA1
L9
Vdd I/O
D4
Vss CORE
L10
A10
D5
OE
L11
Vss I/O
D6
WE
L12
Vdd I/O
D7
SEL3
L13
A11
D8
S5 (2080 Only)
M1
D14
D9
XBOOT
M2
D15
D10
S0/IFIN (2080 only)
M3
Vss I/O
D11
MPE4/LOCK
M4
TRST
D12
Vdd Core
M5
A2
D13
MPE3/MOSI
M6
MPC2/TOC1
E1
BUSCLK
M7
A3
E2
Vss I/O
M8
MPC7/URXD
E3
D2
M9
A7
E4
D1
M10
TEST
Signal and Connection Descriptions
Preliminary
15
MMC2080/2075 Pin Descriptions
Table 4. MMC2080/2075 BGA (144-Pin) Signal ID by Pin Number (Sheet 3 of 3)
Pin Number
16
Signal Name
Pin Number
Signal Name
E10
Vdd OSC
M11
RSTOUT
E11
EXTAL
M12
Vdd I/O
E12
XTAL
M13
UCLK
E13
Vss OSC
N1
Vdd I/O
F1
Vdd I/O
N2
TCK
F2
MPA3
N3
TMS
F3
MPA2
N4
A0
F4
Vdd I/O
N5
MPC1/TIC0
F10
Vdd PLL
N6
Vss I/O
F11
CXFC
N7
A4
F12
Vss PLL
N8
MPC4/URTS
F13
A21
N9
A6
G1
MPA5
N10
A9
G2
MPA4
N11
DE
G3
D3
N12
RESET
G4
D4
N13
Vss I/O
MMC2080/2075 Technical Data
Preliminary
MMC2080/2075 Pin Descriptions
Table 5. MMC2080/2075 PGA (208-Pin) Signal ID by Pin Number (Sheet 1 of 4)
Pin Number
Signal Name
Pin Number
Signal Name
A1
MPB6/ROW2
J4
D3
A2
MPB4/ROW0
J14
A21
A3
BW8
J15
A20
A4
MPB2/COL2
J16
Vss Core
A5
MPB0/COL0
J17
Vss PLL
A6
TA
K1
D8
A7
DVLEB1
K2
Vss I/O
A8
SEL3
K3
D9
A9
SEL1
K4
D21
A10
Vss I/O
K14
A17
A11
DVLEB0
K15
A15
A12
Vss Core
K16
BREQ
A13
S2 (2080 Only)
K17
TC1
A14
S0/IFIN (2080 only)
L1
Vdd I/O
A15
DVLMX
L2
Vss Core
A17
MLDY
L3
D10
B3
MPB5/ROW1
L4
BGNT
B4
PULL_EN
L14
A14
B5
MPB3/COL3
L15
MPE2/MIS0
B6
MPB1/COL1
L16
A18
B7
WE
L17
A19
B8
SEL2
M1
D22
B9
S7 (2080 Only)
M2
D23
B10
S5 (2080 Only)
M3
D12
B11
S6 (2080 Only)
M4
D25
B12
S3 (2080 Only)
M14
A11
B13
DVL1
M15
MPE0/SCLK
B14
LOBAT (2080 Only)
M16
A16
Signal and Connection Descriptions
Preliminary
17
MMC2080/2075 Pin Descriptions
Table 5. MMC2080/2075 PGA (208-Pin) Signal ID by Pin Number (Sheet 2 of 4)
Pin Number
18
Signal Name
Pin Number
Signal Name
M17
Vdd I/O
B17
EXTS0 (2080 Only)
C1
IRQ
N1
D5
C5
D16
N2
D24
C6
ABORT
N3
D6
C7
EB0
N14
UCLK
C8
Vdd I/O
N15
Vdd I/O
C9
TEA
N16
MPE1/SS
C10
XBOOT
N17
Vss I/O
C11
S1 (2080 Only)
P1
D11
C12
DVLO
P2
D7
C13
Vss I/O
P3
TCK
C14
Vdd I/O
P4
TC0
C16
EXTS1 (2080 Only)
P5
TCK
C17
DSTAT4
P6
TC0
D1
Vdd Core
P7
D26
D2
MPA1
P8
VssCore
D3
Vss I/O
P9
A3
D4
EB1
P10
MPC6/UTXD
D5
OE
P11
A8
D6
Vdd Core
P12
DE
D7
OE
P15
Vss I/O
D8
VddCORE
P16
A12
D9
SEL0
P17
A13
D10
S4 (2080 Only)
R1
Vdd Core
D11
SYMCLK (2080 Only)
R2
D14
D12
DVLSEL
R4
Vdd I/O
D13
CLKOUT (2080 Only)
R5
Vss I/O
D16
DSTAT5
R6
HIGHZ
MMC2080/2075 Technical Data
Preliminary
MMC2080/2075 Pin Descriptions
Table 5. MMC2080/2075 PGA (208-Pin) Signal ID by Pin Number (Sheet 3 of 4)
Pin Number
Signal Name
Pin Number
Signal Name
D17
DSTAT1
R7
D27
E1
BUSCLK
R8
A0
E2
D2
R9
MPC2/TOC1
E3
MPA0
R10
MPC4/URTS
E4
MPB7/ROW3
R11
A7
E15
Vdd I/O
R12
TEST
E16
Vss I/O
R13
RSTOUT
E17
MPE3/MOSI
T1
D13
F1
D17
T4
TMS
F2
MPA2
T5
TDO
F3
D0
T6
A1
F4
Vss CORE
T7
MPC1/TIC0
F14
DSTAT3
T8
D28
F15
DSTAT2
T9
MPC0/TOC0
F16
DSTAT0
T10
A5
F17
Vdd OSC
T11
Vdd Core
G1
MPA4
T12
Vdd I/O
G2
Vdd I/O
T13
A10
G3
Vss I/O
T14
D31
G4
D1
T15
RESET
G14
MPE4/LOCK
T16
SHS
G15
Vdd Core
U1
D15
G16
TC2
U4
TDI
G17
XTAL
U5
TRST
H1
MPA5
U6
A2
H2
D18
U7
MPC3/TIC1
H3
Vdd I/O
U8
Vss I/O
H4
MPA3
U9
A4
Signal and Connection Descriptions
Preliminary
19
Tables of Signals
Table 5. MMC2080/2075 PGA (208-Pin) Signal ID by Pin Number (Sheet 4 of 4)
Pin Number
Signal Name
Pin Number
Signal Name
H14
EXTAL
U10
MPC5/UCTS
H15
Vss OSC
U11
MPC7/URXD
H16
CXFC
U12
D29
H17
Vdd PLL
U13
A6
J1
D4
U14
A9
J2
D19
U15
D30
J3
D20
U16
Vss I/O
2.2 Tables of Signals
The MMC2080 input and output signals are organized into functional groups in Table 6 and in Figure 7 on
page 21. Table 7 on page 22 displays data relating to I/O cell names, including descriptions and the
availability of Hi-Z impedance, pull-up resistors, and high drive-current capability. Table 8 on page 23
through Table 20 on page 27 are organized according to signal type and give a brief description of each
signal pin. Package type is indicated as “N” for the 144-pin normal-function package. All pins are available
in the 208-pin development extensions package.
Table 6. MMC2080 Signal Functional Group Organization
Functional Group
Number of Signals
Detailed Description
Arbitration signals
2
Table 20 on page 27
External system bus signals
52
Table 8 on page 23
Development extensions (208-pin package only)
34
Table 9 on page 24
FLEX signals
13
Table 10 on page 25
FSC/SPI signals
5
Table 11 on page 25
SCI signals
5
Table 12 on page 25
Timer signals
4
Table 13 on page 26
Melody generator signals
1
Table 14 on page 26
Keypad signals
8
Table 15 on page 26
Dedicated MPIO signals
6
Table 16 on page 26
SIM signals
2
Table 17 on page 26
JTAG/OnCE signals
6
Table 18 on page 27
Clock and power
40
Table 19 on page 27
20
MMC2080/2075 Technical Data
Preliminary
Tables of Signals
MMC2080
Arbitration
Signals
BREQ
BGNT
External
System
Bus
Signals
MPD[7:0]/D[15:8]
D[7:0]
A[21:0]
EB0–1
BW8
WE
OE
TA
ABORT
BUSCLK
SEL0–3
XBOOT
IRQ
Development
Extensions
(208-Pin
Package)
FLEX
Signals
FSC/SPI
Signals
D[31:16]
DVLEB0–1
DVL0–1
DVLSEL
DSTAT0–5
DVLMX
TC0–2
TEA
HIGHZ
PULL_EN
SHS
LOBAT
EXTS0–1
CLKOUT
SYMCLK
S1–7
S0/IFIN
MPE4/LOCK
MPE3/MOSI
MPE2/MISO
MPE1/SS
MPE0/SCLK
Arbitration Request
Arbitration Grant
High-Order Data Bus
Low-Order Data Bus
Address
Byte Enable
Bus Width (8-Bit)
Data Direction
Output Enable
Transfer Acknowledge
Data Transfer Abort
External Bus Clock
External Device Select
External Boot
Interrupt Request
Extension
Byte Enable
Development Mode
Development Select
Development Status
Status Output Select
Transfer Code
Transfer Error Acknowledge
Tri-State Disable
Pull-up Enable
Show Cycle Strobe
Low Battery
Extension Symbol
Clock Output
Symbol Clock
Serial Port
Serial Port
Synthesizer Lock
Master in/Slave Out
Master Out/Slave In
Slave Select
Serial Clock
Receive Data
Transmit Data
Clear-To-Send
Request-To-Send
UART Clock
MPC7/URXD
MPC6/UTXD
MPC5/UCTS
MPC4/URTS
UCLK
SCI
Signals
Timer1 Input Capture
Timer1 Output Capture
Timer0 Input Capture
Timer0 Output Capture
MPC3/TIC1
MPC2/TOC1
MPC1/TIC0
MPC0/TOC0
Timer
Signals
MLDY
Melody
Generator
Signal
MPB[7:4]/ROW[3:0]
MPB[3:0]/COL[3:0]
Keypad
Signals
MPA[5:0]
MPIO
Signals
Generator Waveform
Row Detect
Column Detect
Master Reset
Reset Output
Test Mode Select
Test Clock
Test Data In
Test Data Out
TAP Reset
Debug Enable
Oscillator Circuit Input
Oscillator Circuit Output
PLL Filter Capacitor
Core Power
Core Ground
I/O Pad Power
I/O Pad Ground
Oscillator Power
Oscillator Ground
PLL Power
PLL Ground
VDD
RESET
RSTOUT
SIM
Signals
TMS
TCK
TDI
TDO
TRST
DE
JTAG/OnCE
Signals
EXTAL
XTAL
CXFC
VDDCORE[5]
VSSCORE[5]
IOVDD[11]
IOVSS[11]
Clock
and
Power
OSCVDD
OSCVSS
PLLVDD
PLLVSS
Figure 7. MMC2080 Signal Group Organization
Signal and Connection Descriptions
Preliminary
21
Tables of Signals
Table 7. I/O Cell Description
I/O Cell Name
Hi-Z
Pull-up
High
Drive
Capable
OTP
Tri-state output with selectable drive strength; always enabled
with strong drive except during JTAG Hi-Z command or unless
otherwise stated
Y
N
Y
INHP
Input with hysteresis
N
N
N
INHP with selectable pull-up enable
N
Y
N
INHP and OTP
Y
N
Y
IOHPPH
INHPP and OTP
Y
Y
Y
SWIOP
High-current IOHPPH
Y
Y
Y
Analog input/output (same cell)
N
N
N
INHPP
IOHP
AIN/AOT
22
Description
MMC2080/2075 Technical Data
Preliminary
Tables of Signals
Table 8. External System Bus Signals
Signal Name
Dir
N
I/O Cell
MPD[7:0]/D[15:8]
I/O
Y
IOHPPH
High-Order Data Bus—May be used as general I/O when the
data bus is configured as an 8-bit bus. Output drivers are
disabled and pull-up resistors are enabled during reset.
D[7:0]
I/O
Y
IOHPPH
Low-Order Data Bus—Output drivers are disabled and pull-up
resistors are enabled during reset.
A[21:0]
I/O
Y
IOHP
Address—Input when BGNT is low; otherwise output. Twentytwo bits is a 4 Mbyte address space.
EB[1:0]
I/O
Y
IOHP
Byte Enable (active low)—Input when BGNT is low; otherwise
output. EB0 enables D[15:8] and EB1 enables D[7:0]. When the
data bus is configured as an 8-bit bus, EB0 is always released
(high) and EB1 is always asserted (low).
BW8
I/O
Y
IOHPPH
Bus Width 8 (open-drain, active low)—If this pin is driven low
either externally or internally, the external bus functions as an 8bit bus.
WE
I/O
Y
IOHP
Write Enable (active low)—Input when BGNT is low. When WE
is low, data is driven by an external device and received by the
MMC2080. Output when BGNT is high. When WE is low, data is
driven by the MMC2080 and received by an external device.
OE
I/O
Y
IOHP
Output Enable (active low)—Input when BGNT is low; when OE
is high, D[7:0] (and D[15:8] when in 16-bit mode) external data
drivers are disabled. Output when BGNT is high; when OE is
high, drivers are disabled.
TA
O
Y
OTP
Transfer Acknowledge (active low)—An external transaction
continues when this pin is high. When low, the external data
transfer cycle will complete. When MONITOR mode is set. TA
also indicates the end of internal transactions.
ABORT
O
Y
OTP
Data Transfer Abort (active low)—When a transaction is
aborted, this pin is driven low.
BUSCLK
O
Y
OTP
External Bus Clock.
SEL[3:0]
O
Y
OTP
External Device Select—SEL0 is always active low; SEL[3:1]
may be individually programmed as active low or active high.
After reset, SEL3 is active high. SEL1 and SEL2 are active low
after restart.
XBOOT
I
Y
INHPP
External Boot (active low)—If this pin is low after a reset, the
external boot portion of the system memory map is enabled;
otherwise the internal boot map is enabled.
IRQ
O
Y
OTP
Interrupt Request—This is driven high when either a normal
interrupt or a fast interrupt is generated by the interrupt
controller.
Description
Signal and Connection Descriptions
Preliminary
23
Tables of Signals
Table 9. Development Extensions (208-Pin Package)
Signal Name
Dir
N
I/O Cell
Description
D[31:16]
I/O
N
IOHPPH
Extension to provide a 32-bit external bus. The bus is enabled when
either DVL0 or _DVL0 is asserted.
DVLEB[1:0]
I/O
N
IOHPPH
Byte Enable (active low)—Input when BGNT is low; otherwise
output. DVLEB0 enables D[31:24] and DVLEB1 enables D[23:16].
DVL[1:0]
I
N
INHPP
Development Mode—When DVL1 is low, the internal ROM is
bypassed. If the ROM space is addressed when DVL1 is low and
XBOOT is high, the 32-bit extension is enabled and DVLSEL is
asserted to select an external memory.
When DVL0 is low, the 32-bit bus extension is enabled for external
bus masters (BGNT is low) and for debug monitor modes.
24
DVLSEL
O
N
OTP
DVLMX
I
N
INHPP
DSTAT[5:0]
O
N
OTP
When DVLMX is high, DSTAT is the low-order 6 bits of the interrupt
vector. When DVLMX is low, DSTAT[3:0] is the M•CORE pipeline
status, PSTAT[3:0], and DSTAT[5:4] is the transfer size in M•CORE
format.
TC[2:0]
O
N
OTP
Processor Transfer Code.
TEA
I
N
INHPP
Transfer Error Acknowledge (active low).
HIGHZ
I
N
INHPP
Tri-State Disable (active low)—When asserted (low), all tri-state
outputs are disabled (high-z). This performs the same function as
the JTAG HIGHZ command.
PULL_EN
I
N
INHPP
Enable Pull-up Resistors—When low, all pull-up resistors (except
the pull-up resistor on this I/O cell) are disabled.
SHS
O
N
OTP
Show Cycle Strobe (active low)— Strobes low when data is valid.
Development Select (active low)—When DVL1 is low and XBOOT
is high, this output is asserted when the internal ROM locations are
addressed.
Selects the output of DSTAT[5:0].
MMC2080/2075 Technical Data
Preliminary
Tables of Signals
Table 10. FLEX Signals (MMC2080 Only)
Signal Name
Dir
N
I/O Cell
Description
LOBAT
In
Y
INHP
Low Battery—LOBAT is an input signal to indicate to the MMC2080
when external battery power is going low. (An external voltage
sensing circuit is required.) Polarity is programmable.
EXTS[1:0]
In
Y
IOHP
External Symbol —EXTS 1 is the MSB of the current FLEX symbol.
EXTS0 is the LSB of the current FLEX symbol. These pins are used
when demodulation is being performed externally.
CLKOUT*
O
Y
OTP
Clock Output—CLKOUT is programmable as a 38.4 or 40 kHz
clock output (derived from oscillator).
SYMCLK
O
Y
OTP
Recovered Symbol Clock—Data is synchronized to the internal
clock, and this recovered clock output enhances lock-on capability
by reducing jitter from cable-induced noise.
S[7:1]
O
Y
OTP
Control Lines 1–7—These signals are the seven additional receiver
control lines. Selectable polarity.
S0/IFIN
I/O
Y
IOHP
S0—This signal is a receiver control output line when the IDE bit is
clear (that is, the internal demodulator is disabled).
IFIN—This signal is a limited IF input when the IDE bit is set (that is,
the internal demodulator is enabled).
Table 11. FSC/SPI1 Signals
Signal Name
Dir
N
I/O Cell
Description
MPE4/LOCK
I/O
Y
IOHPPH
External Synthesizer Lock Input—PIO when SPI1 is disabled
MPE3/MOSI
I/O
Y
IOHPPH
Master-out / Slave-in—PIO when SPI1 is disabled
MPE2/MISO
I/O
Y
IOHPPH
Master-in / Slave-out—PIO when SPI1 is disabled
MPE1/SS
I/O
Y
IOHPPH
Slave Select (selectable polarity)—PIO when SPI1 is disabled
MPE0/SCLK
I/O
Y
IOHPPH
Serial Clock—PIO when SPI1 is disabled
Table 12. SCI Signals
Signal Name
Dir
N
I/O Cell
MPC7/URXD
I/O
Y
IOHPPH
Receive Data—An input when used as URXD; otherwise a PIO
MPC6/UTXD
I/O
Y
IOHPPH
Transmit Data—An output when used as UTXD; otherwise a PIO
MPC5/UCTS
I/O
Y
IOHPPH
Clear-to-Send (active low)—An input when used as UCTS;
otherwise a PIO
MPC4/URTS
I/O
Y
IOHPPH
Request-to-Send (active low)—An output when used as URTS;
otherwise a PIO
UCLK
I/O
Y
IOHPPH
UART Clock
Description
Signal and Connection Descriptions
Preliminary
25
Tables of Signals
Table 13. Timer Signals
Signal Name
Dir
N
I/O Cell
Description
MPC3/TIC1
I/O
Y
IOHPPH
Timer1 Input Capture—An input when used as TIC1; otherwise a
PIO
MPC2/TOC1
I/O
Y
IOHPPH
Timer1 Output Capture—An output when used as TOC1;
otherwise a PIO
MPC1/TIC0
I/O
Y
IOHPPH
Timer0 Input Capture—An input when used as TIC0; otherwise a
PIO
MPC0/TOC0
I/O
Y
IOHPPH
Timer0 Output Capture—An output when used as TOC0;
otherwise a PIO
Table 14. Melody Generator Signal
Signal Name
Dir
N
I/O Cell
MLDY
O
Y
OTP
Description
Melody Generator Waveform
Table 15. Keypad Signals
Signal Name
Dir
N
I/O Cell
Description
MPB[7:4]/
ROW[3:0]
I/O
Y
IOHPPH
Row Detect—Inputs when used as row detect; otherwise a PIO
MPB[3:0]/
COL[3:0]
I/O
Y
IOHPPH
Column Select—Open-drain outputs when used as column
select; otherwise a PIO
Table 16. MPIO Signals
Signal Name
Dir
N
I/O Cell
Description
MPA[5:0]
I/O
Y
SWIOP
These bits can be individually programmed as input (with selectable
pull-up resistor), output (with selectable drive strength), or external
interrupt (with selectable assertion level). Each GPIO input pin is
latched at the beginning of a read cycle.
Other pins when
configured as
PIO
I/O
Y
IOHPP
H
These bits can be individually programmed as input (with selectable
pull-up resistor) or output (with selectable drive strength). Each
MPIO input pin is latched at the beginning of a read cycle.
Table 17. SIM Signals
26
Signal Name
Dir
N
I/O Cell
Description
RESET
I
Y
INHP
External Reset (active low)
RSTOUT
O
Y
OTP
Reset Output (active low)
MMC2080/2075 Technical Data
Preliminary
Tables of Signals
Table 18. JTAG/OnCE™ Signals
Signal Name
Dir
N
I/O Cell
Description
TMS
I
Y
INHPP
Test Mode Select—Pull-up resistor always enabled
TCK
I
Y
INHPP
Test Clock—Pull-up resistor always enabled
TDI
I
Y
INHPP
Test Data In—Pull-up resistor always enabled
TDO
O
Y
OTP
Test Data Out
TRST
I
Y
INHP
TAP Reset (active low)
DE
I/O
Y
IOHPPH
Debug Enable (open drain, active low)
Table 19. Clock and Power
Signal Name
N
I/O Cell
Description
EXTAL
Y
AIN
Oscillator circuit input—external 76.8 kHz crystal
XTAL
Y
AOT
Oscillator circuit output
CXFC
Y
AIN
PLL filter capacitor
VddCore (5)
Y
Power
Core power
VssCore(5)
Y
Power
Core ground
VddIO (11)
Y
Power
I/O pad power
VssIO (11)
Y
Power
I/O pad ground
VddOSC
Y
Power
Oscillator power
VssOSC
Y
Power
Oscillator ground
VddPLL
Y
Power
PLL power
VssPLL
Y
Power
PLL ground
Table 20. Arbitration Signals
Signal Name
Dir
N
I/O Cell
Description
BREQ
I
Y
INHPP
Arbitration Request (active low)—Request mastership of the
internal system bus; pull-up resistor always enabled
BGNT
O
Y
OTP
Arbitration Grant (active low)—Indicates system bus is granted to
external master
Signal and Connection Descriptions
Preliminary
27
General Characteristics
Part 3 Specifications
3.1 General Characteristics
The MMC2080/2075 specifications are preliminary, from design simulations, and may not be fully tested
or guaranteed at this early stage of the product life cycle. Finalized specifications will be published upon the
completion of full characterization and device qualifications.
3.2 Maximum Ratings
WARNING:
This device contains circuitry protecting against damage due to high static
voltage or electrical fields; however, normal precautions should be taken to
avoid exceeding maximum voltage ratings. Reliability is enhanced if
unused inputs are tied to an appropriate logic voltage level (for example,
either Vss or Vdd).
NOTE:
In the calculation of timing requirements, adding a maximum value of one
specification to a minimum value of another specification does not yield a
reasonable sum. A maximum specification is calculated using a worst-case
variation of process parameter values in one direction. The minimum
specification is calculated using the worst-case variation for the same
parameters in the opposite direction. Therefore, a “maximum” value for a
specification will never occur in the same device that has a “minimum”
value for another specification; adding a maximum to a minimum
represents a condition that can never exist.
Table 21. DC Absolute Maximum Operating Conditions
Characteristics
Supply (All)
Symbol
Min
Typ
Max
Vdd
1.8
3.0
3.6
Units
V
Input Voltage Range
VI
V
Input Clamp Current
(V1<0 or V1>QVDDH)
II
mA
Output Clamp Current
(V1<0 or V1>QVDDH)
IO
mA
Storage Temperature Range
o
C
Remaining specification information to be provided.
28
MMC2080/2075 Technical Data
Preliminary
BGA Details
Part 4 Pin-out and Package Information
This section provides information about the available packages for this product. The MMC2080/2075 is
available in a 144-pin Ball Grid Array (BGA) package. A 208-pin Pin Grid Array (PGA) is produced for
engineering use only. Contact the factory for availability.
4.1 BGA Details
The MMC2080/2075 is offered in the JEDEC-standard, Mold Array Process (MAP), 12 mm x 12 mm BGA
with 0.8 mm ball pitch (0.4 mm small solder balls). Refer to Figure 8 for the package drawings and
dimensions.
4.1.1
BGA Package Mechanical Drawings
The mechanical drawings for the 144-pin Ball Grid Array package are shown in Figure 8.
X
D
Y
DETAIL K
LASER MARK FOR PIN 1
IDENTIFICATION IN
THIS AREA
M
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994.
3. DIMENSION b IS MEASURED AT THE MAXIMUM
SOLDER BALL DIAMETER, PARALLEL TO DATUM
PLANE Z.
4. DATUM Z (SEATING PLANE) IS DEFINED BY THE
SPHERICAL CROWNS OF THE SOLDER BALLS.
5. PARALLELISM MEASUREMENT SHALL EXCLUDE ANY
EFFECT OF MARK ON TOP SURFACE OF PACKAGE.
E
M
0.15
12X
13 12 11 10 9
8
5
4
3
e
METALIZED MARK
FOR PIN 1 IDENTIFICATION
IN THIS AREA
2
1
e
A
B
C
D
E
F
G
H
J
K
L
M
12X
MILLIMETERS
MIN
MAX
1.25
1.60
0.18
0.34
1.16 REF
0.35
0.45
12.00 BSC
12.00 BSC
0.80 BSC
DIM
A
A1
A2
b
D
E
e
5
0.20 Z
A A2
A1
Z
4
0.10 Z
N
DETAIL K
3
144X
ROTATED 90 ° CLOCKWISE
b
0.15 Z X Y
VIEW M-M
0.08 Z
Figure 8. MMC2080/2075 BGA Mechanical Drawings
Pin-out and Package Information
Preliminary
29
PGA Details
4.2 PGA Details
The MMC2080/2075 is also offered in a ceramic, 43 mm x 43 mm PGA for engineering use only. Contact
the factory for availability. Refer to Figure 9 for the package drawings and dimensions.
4.2.1
PGA Package Mechanical Drawings
The mechanical drawings for the 208-pin Ball Grid PGA package are shown in Figure 9.
F
C
G
A
D
SEATING
PLANE
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994.
3. MINIMUM SPACING BETWEEN CONDUCTORS SHALL
BE 0.500.
DIM
D
E
F
G
H
K
L
b
e
E
MILLIMETERS
MIN
MAX
42.70
43.70
42.70
43.70
1.78
3.68
1.14
1.90
0.08
----2.00
2.54
5.00
0.40
0.50
2.54 BSC
L
B
0.200 C
16X
16X
K
e
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
e
208X
4X
H
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
b
0.500
M
C A
0.250
M
C
M
B
M
Figure 9. MMC2080/2075 PGA Mechanical Drawings
30
MMC2080/2075 Technical Data
Preliminary
Ordering Drawings
4.3 Ordering Drawings
Complete mechanical information regarding MMC2080/2075 packaging is available by facsimile through
Motorola’s MFAX™ system. Call the following number to obtain information by facsimile:
(602) 244-6591
The MFAX automated system requests the following information:
•
The receiving facsimile telephone number, including area code or country code
•
The caller’s personal identification number (PIN)
NOTE:
For first-time callers, the system provides instructions for setting up a PIN,
which requires the entry of a name and telephone number.
•
The type of information requested:
— Instructions for using the system
— A literature order form
— Specific-part technical information or datasheets
— Other information described by the system messages
A total of three documents may be ordered per call.
The MMC2080/2075 144-pin BGA package mechanical drawing is referenced as Case 1248A-01 Rev. 0.
The MMC2080/2075 208-pin BGA package mechanical drawing is referenced as Case 1297-01 Rev. 0.
Pin-out and Package Information
Preliminary
31
Heat Dissipation
Part 5 Design Considerations
5.1 Heat Dissipation
An estimate of the MMC2080/2075 chip junction temperature, TJ, in °C can be obtained from the following
equation.
T J = T A + ( PD × R θ JA )
Where:
TA = ambient temperature °C
RθJA = package junction-to-ambient thermal resistance °C/W
PD = power dissipation in package
Historically, thermal resistance has been expressed as the sum of a junction-to-case thermal resistance and
a case-to-ambient thermal resistance, as follows:
Rθ JA = R θ JC + Rθ CA
Where:
RθJA = package junction-to-ambient thermal resistance °C/W
RθJC = package junction-to-case thermal resistance °C/W
RθCA = package case-to-ambient thermal resistance °C/W
RθJC is device related and cannot be influenced by the user. The user controls the thermal environment to
change the case-to-ambient thermal resistance, RθCA. For example, the user can change the air flow around
the device, add a heat sink, change the mounting arrangement on the printed circuit board, or otherwise
change the thermal dissipation capability of the area surrounding the device on a printed circuit board. This
model is most useful for ceramic packages with heat sinks; ninety percent of the heat flow is dissipated
through the case to the heat sink and out to the ambient environment. For ceramic packages, in situations
where the heat flow is split between a path to the case and an alternate path through the printed circuit board,
analysis of the device’s thermal performance may need the additional modeling capability of a system-level
thermal simulation tool.
The thermal performance of plastic packages is more dependent on the temperature of the printed circuit
board to which the package is mounted. Again, if the estimations obtained from RθJA do not satisfactorily
answer whether the thermal performance is adequate, a system-level model may be appropriate.
A complicating factor is the existence of three common ways for determining the junction-to-case thermal
resistance in plastic packages:
•
To minimize temperature variation across the surface, the thermal resistance is measured from the
junction to the outside surface of the package (case) closest to the chip mounting area when that
surface has a proper heat sink.
•
To define a value approximately equal to a junction-to-board thermal resistance, the thermal
resistance is measured from the junction to where the leads are attached to the case.
•
If the temperature of the package case (TT) is determined by a thermocouple, the thermal resistance
is computed using the value obtained by the equation (TJ - TT)/PD.
As noted previously, the junction-to-case thermal resistances quoted in this document are determined using
the first definition. From a practical standpoint, this value is also suitable for determining the junction
32
MMC2080/2075 Technical Data
Preliminary
Electrical Design Considerations
temperature from a case thermocouple reading in forced convection environments. In natural convection,
using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple reading
on the case of the package will estimate a junction temperature slightly hotter than the actual temperature.
Hence, the new thermal metric, thermal characterization parameter or ΨJT, has been defined to be (TJ - TT)/
PD. This value gives a better estimate of the junction temperature in natural convection when using the
surface temperature of the package. Remember that surface temperature readings of packages are subject to
significant errors caused by inadequate attachment of the sensor to the surface and to errors caused by heat
loss to the sensor. The recommended technique is to attach a 40-gauge thermocouple wire and bead to the
top center of the package with thermally conductive epoxy.
NOTE:
Section 3, “Specifications,” on page 28 of this document contains the
package thermal values for this chip.
5.2 Electrical Design Considerations
WARNING:
This device contains protective circuitry to guard against damage due to
high static voltage or electrical fields. However, normal precautions are
advised to avoid application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of operation is
enhanced if unused inputs are tied to an appropriate logic voltage level (for
example, either Vss or VDD).
Use the following list of recommendations to assure correct operation:
•
Provide a low-impedance path from the board power supply to each Vdd pin on the MMC2080/
2075 and from the board ground to each Vss pin.
•
Use at least four 0.1 µF bypass capacitors positioned as close as possible to the four sides of the
package to connect the Vdd power source to Vss.
•
Ensure that capacitor leads and associated printed circuit traces that connect to the chip Vdd and
Vss pins are less than 0.5 inch per capacitor lead.
•
Use at least a four-layer printed circuit board (PCB) with two inner layers for Vdd and Vss.
•
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating
capacitance. This is especially critical in systems with higher capacitive loads that could create
higher transient currents in the Vdd and Vss circuits.
•
All inputs must be terminated (that is, not allowed to float) using CMOS levels.
Take special care to minimize noise levels on the PLL supply pins (both Vdd and Vss).
Design Considerations
Preliminary
33
OnCE, M•CORE, MFAX, Roaming FLEX, FLEX Alphanumeric Chip, FLEX Chip, FLEX Numeric Chip, and FLEX
Stack are trademarks of Motorola, Inc.
This document contains information on a new product. Specifications and information herein are subject to change
without notice.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can
and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must
be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent
rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems
intended for surgical implant into the body, or other applications intended to support life, or for any other application in which the
failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use
Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
All other tradenames, trademarks, and registered trademarks are the property of their respective owners.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado, 80217
1-303-675-2140 or 1-800-441-2447
JAPAN: Motorola Japan, Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu, Minato-ku,
Tokyo 106-8573 Japan. 81-3-3440-3569
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd., Silicon Harbour Centre, 2 Dai King Street,
Tai Po Industrial Estate, 2 Tai Po, N.T., Hong Kong. 852-26668334
Customer Focus Center: 1-800-521-6274
Mfax™: [email protected]
–TOUCHTONE 1-602-244-6609
–US & Canada ONLY 1-800-774-184
–http://sps.motorola.com/mfax/
HOME PAGE: http://motorola.com/sps
Motorola DSP Products Home Page: http://www.motorola-dsp.com
MMC2080/2075/D