Preliminary Data Sheet V23870-A211x-xx00(*) Bi-Directional Pigtail SFF Transceiver 155 Mb/s, 1310 nm Tx / 1310 nm Rx FEATURES • Integrated Beam Splitter • Bi-Directional Transmission in a single optical window • Single fiber solution, singlemode fiber pigtail with different connector options • Data rate up to 155 Mbit/s • FP Laser Diode with Multi-Quantum Well structure, wavelength 1310 nm • Class 1 Laser Product • Incorporated laser driver and PIN-TIA Receiver with post-amplifier • 2x5 Small Form Factor Package with Multisource Footprint Absolute Maximum Ratings Operating case temperature V23870-A2111-xx00 ....................... 0 to 70 °C V23870-A2112-xx00 .................... -40 to 85 °C Storage Ambient Temperature ................. -40 to 85 °C Supply voltage .................................................. 3.53 V Soldering Conditions Temp/Time Iron Soldering only .................... 400 °C / 10 s *) Ordering Information V23870 - A211x - xx00 Average Launched Power: 2: -8 ... -13 dBm Temperature Range: 1: 0 ... +70 °C 2: -40 ... +85 °C Connector: A: Pigtail Only B: SC C: SC/APC 8° F: MU H: MU-J K: LC Coupling: (Tx/Rx, Signal Detect) 1: AC/AC, PECL SD 2: DC/DC, PECL SD 5: AC/AC, TTL SD 6: DC/DC, TTL SD Fiber Optics JULY 2002 DESCRIPTION The Infineon BIDI® transceiver – part of Infineon’s Small Form Factor transceiver family – is based on the Physical Medium Depend (PMD) sublayer and baseband medium. Infineon's BIDI-TRX is designed to handle multiple data rates and can be designed into Fast Ethernet, FDDI, Fiber Channel, ATM-155, SDH STM-1, SONET OC-3, CCTV and other applications as well as different FTTx applications according to the 100 Mbps EFM standard (IEEE 802.3ah). It is suitable for both, short haul applications and distances of 20 km and beyond. The appropriate fiber optic cable is the 9µm singlemode fiber pigtail with different connector options. The Infineon BIDI transceiver is a single unit comprised of a transmitter, a receiver, WDM filter or beam splitter, and a singlemode fiber pigtail. This design frees the customer from many alignment and PC board layout concerns. This transceiver operates at 155Mb/s from a single power supply (+3.3 V). The full differential data inputs and outputs are PECL and LVPECL compatible. Functional Description of 2x5 Pin Row Transceiver This transceiver is designed to transmit and receive serial data via a singlemode cable. Functional Diagram Fiber Optics 2 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver The receiver component converts the optical serial data into PECL compatible electrical data (RD and RDnot). The Signal Detect (SD, active high) shows whether an optical signal is present. The transmitter converts PECL compatible electrical serial data (TD and TDnot) into optical serial data. Data lines are differentially 100Ω terminated. The transmitter contains a laser driver circuit that drives the modulation and bias current of the laser diode. The currents are controlled by a power control circuit to guarantee constant output power of the laser over temperature and aging. The power control uses the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the operating limits. Single fault condition is ensured by means of an integrated automatic shutdown circuit that disables the laser when it detects laser fault to guarantee the laser Eye Safety. The transceiver contains a supervisory circuit to control the power supply. This circuit makes an internal reset signal whenever the supply voltage drops below the reset threshold. It keeps the reset signal active for at least 140 milliseconds after the voltage has risen above the reset threshold. During this time the laser is inactive. The laser can be disabled by the TxDis input. Technical Data The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Recommended Operating Conditions Symbol Min. Operating Temperature Range at Case 1 TC Operating Temperature Range at Case 2 Power Supply Voltage Typ. Max. Unit 0 +70 °C TC -40 +85 °C VCC-VEE 3.1 3.53 V VDIFF 250 1600 mV λC 1500 1600 nm 3.3 Transmitter Data Input Differential Voltage Receiver Input Center Wavelength 1 2 For V23870-A2111-xx00 For V23870-A2112-xx00 Fiber Optics 3 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver Transmitter Symbol Min. Average Launched Power Pout,max -13 Emission wavelength center of range3 λ Spectral bandwidth (RMS) σλ 3.0 nm Temperature coefficient of emission wavelength ∆λ(T) 0.5 nm/K Extinction Ratio (Dynamic) ER Jitter (pkpk) JPP 1 ns Rise Time (20% - 80%) tR 2.5 ns 5 tF 2.5 ns -120 dB/√Hz 4 Fall Time (20% - 80%) 1270 Typ. -8 dBm 1350 8.5 nm dB ITU G.957 mask pattern RIN Noise RIN 5 Unit 1310 Eye diagram Reset Threshold Max. VTH 2.5 2.75 2.99 V Reset Timeout5 tRES 140 240 560 ms Power on Delay tPWR_ON 88 111 140 ms Shut Off Time for TxDis tDIS 6 ms Max Tx Supply Current ITX 135 mA 3 4 5 90 Popt = Pout,max at T=25°C Rise and fall times are measured with the OC-3 filter ON Laser power is shut down if power supply is below VTH and switch on if power supply is above VTH after tRES. Fiber Optics 4 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver Receiver Symbol Receiving wavelength center of range λR 6 Sensitivity (Average Power)7 PIN Saturation (Average Power) PSAT Signal Detect Assert Level 8 Signal Detect Deassert Level Min. 1270 Typ. 1310 Signal Detect Hysteresis 1350 -21 -3.0 -22 PSDD -31 PSDA- 0.5 Unit nm dBm dBm PSDA 9 Max. dBm dBm 4 6 dB PSDD Signal Detect Assert Time tASS 100 µs Signal Detect Deassert Time tDAS 350 µs 1.0 V 1.5 ns 130 mA Data Output Differential Voltage 10 VDIFF Rise/Fall Time 0.8 tR; tF Max Rx Supply Current 11 IRX Module Electro-Optical Characteristics Optical Isolation 0.4 Symbol 12 ORL 60 Min. 14 Typ. Max. Unit dB 6 Popt = Pout,max at T=25°C Minimum average optical power at which the BER is less than1x10E–10. Measured with a 1023 –1 NRZ PRBS as recommended by ANSI T1E1.2, SONET OC-3, and ITU G.957. 8 An increase in optical power above the specified level will cause the SIGNAL DETECT output to switch from a Low state to a High state. 9 A decrease in optical power below the specified level will cause the SIGNAL DETECT to change from a High state to a Low state. 10 AC/AC for data. Load 50Ω to GND or 100Ω differential. For dynamic measurement a tolerance of 50mV should be added. 11 Supply current excluding Rx output load. 12 Source wavelength is 1550 nm, BiDi Tx and Rx is Off 7 Fiber Optics 5 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver Fiber Data The mechanical fiber characteristics are described in the following table. Fiber Characteristics Min. Typ. Max. 8 9 10 µm 123 125 127 µm Mode Field/Cladding Concentricity Error 1 µm Cladding Non-circularity 2 % Mode Field Non-circularity 6 nm Mode Field Diameter Cladding Diameter Cut off Wavelength 1270 Unit nm Jacket Diameter 0.8 Bending Radius 30 mm Tensile Strength Fiber Case 5 N Length Fiber Optics 0.8 6 1 1.2 mm m V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver Pin Description Pin Name VEEr Receiver Signal Ground VCCr Receiver Power Supply SD Signal Detect Level/ Logic N/A N/A see options on page 1 Pin# 1 2 3 RD– RD+ VCCt VEEt TxDis PECL PECL N/A N/A TTL-Input 4 5 6 7 8 PECL PECL N/A 9 10 MS1 MS2 N/A T1 T2 T3 T4 Received Data Out Not Received Data Out TD+ TD– MS Transmitter Disable/Enable Transmit Data Transmit Data Not Mounting Studs HL Housing Leads Fiber Optics 7 Description Normal Operation: Logic “1” Output, represents that light is present at receiver input Fault Condition: Logic “0” Output Recommended Termination of 510 Ω to Veer for PECL Transmitter Power Supply Transmitter Signal Ground A low/open signal switches the laser on. A high signal switches the laser off. Transmitter Data In Transmitter Data In Not Mounting Studs are provided for transceiver mechanical attachment to the circuit board. The transceiver Housing Leads are provided for additional signal grounding. The holes in the circuit board must be included and be tied to signal ground. V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver Technical drawings 9.71 .382 13.50 .531 3 .118 12 .472 0.38 .015 1.78 .070 0.25 .010 7.11 .280 TEMPERATURE MEASUREMENT LOCATION 49.01 1.930 3.92 .154 2X 17.79 .700 1.07 .042 4.56 .180 20.19 .795 3.10 .122 +10 0 +.394 .877 - .000 22.27 13.50 .531 10.16 .400 1.40 .055 20X 0.81 .032 5.15 .203 21.34 .840 23.88 .940 1.84 .072 13.34 .525 NOTES: 1. FIBER AND CONNECTOR NOT SHOWN. 2. REFER TO PACKAGE OUTLINE OF THE SMALL FORM FACTOR TRANSCEIVER MULTISOURCE AGREEMENT FOR DIMENSIONS NOT SHOWN. 15.75 .620 FRONT OF BEZEL Circuit Board Layout Recommended PCB Thickness 0.1 (2.54) max. Fiber Optics 8 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver EYE SAFETY This laser based singlemode transceiver is a Class 1 product. It complies with IEC 60825-1 and FDA 21 CFR 1040.10 and 1040.11. To meet laser safety requirements the transceiver shall be operated within the maximum operating limits. Caution All adjustments have been made at the factory prior to shipment of the devices. No maintenance or alteration to the device is required. Tampering with or modifying the performance of the device will result in voided product warranty. Note: Failure to adhere to the above restrictions could result in a modification that is considered an act of “manufacturing,” and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR 1040.10 (i)). APPLICATION NOTES Transceiver Assembly/Soldering Recommended requirements • avoid temperatures on fiber and connector above 85°C • only iron soldering permitted • single pin or simultaneous pin soldering valid Type Conditions Iron - soldering iron tip temp. solder time Fiber Optics Standard < 400 °C IEC 68 2-20 test Tb, methode 2 < 10 sec 9 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver AC/AC coupling Vcc 3.3V C3 L1 Vcc SerDes 3.3V L2 C1 C2 TxVcc (6) RxVcc (2) TxVee (7) Vcc TD+ (9) Laser Driver Ser Data Out+ 100 Ohms TD- (10) R1 TxDis (8) SD (3) Limiting Amplifier R2 ECL/PECL Driver Ser Data Out- Serializer/ Deserializer SD R7 R3 R4 Rd- (4) Ser Data InReceiver Rd+ (5) SFF Transceiver Ser Data In+ RxVee (1) R5 R6 L1, L2: 1...4.7 µH C1, C2, C3: 4.7...10 µF R1, R2: biasing of outputs depending on Serializer R3, R4: 127 Ohms R5, R6: 80 Ohms R7: 510 Ohms for PECL signal detect, open for TTL Place R1/2/3/4/5/6 as close to SerDes chip as possible Fiber Optics 10 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver DC/DC coupling Vcc 3.3V C3 L1 Vcc SerDes 3.3V L2 C1 C2 TxVcc (6) RxVcc (2) TxVee (7) R6 R7 Vcc C6 TD+ (9) Laser Driver Ser Data Out+ R9 TD- (10) R4 R5 R8 TxDis (8) SD (3) Limiting Amplifier ECL/PECL Driver C7 Ser Data Out- Serializer/ Deserializer SD R10 C4 Rd- (4) Ser Data InReceiver R1 Rd+ (5) Ser Data In+ C5 SFF Transceiver RxVee (1) R2 R3 L1, L2: 1...4.7 µH C1, C2, C3: 4.7...10 µF C4, C5, C6, C7: 100 nF R1: 100 Ohms R2, R3: 150 Ohms R4, R5: biasing of outputs depending on Serializer R6, R7: 127 Ohms R8, R9: 80 Ohms R10: 510 Ohms for PECL signal detect, open for TTL Place R1/4/5 as close to SerDes as possible Place R2/3 as close to transceiver as possible Fiber Optics 11 V23870-A2111/2-xx00 BIDI Pigtail SFF transceiver