SOURCE C-13-155-F-SLC3A-12-G5

155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Ultra Long reach SONET OC-3/SDH STM-1 Compliant
• Single +3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVPECL Signal Detection Output
• Temperature Range: -40 to 85 ºC
• Class 1 Laser International Safety Standard IEC 825
Compliant
• Solder ability to MIL-STD-883, Method 2003
• Pin coating is Sn/Pb with minimum 2% Pb content
• Flammability to UL94V0
• Humidity RH 5-85% (5-95% short term) to IEC 68-2-3
• Complies with Telcordia(Bellcore) GR-468-CORE
• Uncooled laser diode with MQW structure
• EMI Shielding Finger Optional
• ATM 155 Mbps links
• RoHS compliance available
Absolute Maximum Rating
Symbol
Min.
Max.
Unit
Power Supply Voltage
Parameter
Vcc
0
3.6
V
Output Current
Iout
0
30
mA
Soldering Temperature
-
-
260
ºC
Operating Temperature
Topr
-40
85
ºC
Storage Temperature
Tstg
-40
85
ºC
Note
10 seconds on leads only
Recommended Operating Condition
Symbol
Min.
Typ.
Max.
Unit
Power Supply Voltage
Parameter
Vcc
3.1
3.3
3.5
V
Operating Temperature (Case)
Topr
-40
-
85
ºC
-
-
155
-
Mbps
Data Rate
LUMINENTOIC.COM
Note
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Po
-15
-
-8
dBm
C-13-155-F-SLC3A-12
Optical
Optical Transmit Power
Optical Transmit Power
Po
-5
-
0
dBm
C-13-155-F-SLC5A-12
Output Center Wavelength
λp
1261
1310
1360
nm
C-13-155-F-SLC3A-12
Output Center Wavelength
λp
1263
1310
1360
nm
C-13-155-F-SLC5A-12
Output Spectrum Width
∆λrms
-
-
7.7
nm
RMS(σ), C-13-155-F-SLC3A-12
Output Spectrum Width
∆λrms
-
-
3
nm
RMS(σ), C-13-155-F-SLC5A-12
Extinction Ratio
ER
8.2
-
-
dB
C-13-155-F-SLC3A-12
Extinction Ratio
ER
10
-
-
dB
C-13-155-F-SLC5A-12
Output Eye
Compliant with Bellcore GR-253-CORE and ITU recommendation G.957
Optical Rise Time
tr
-
-
2
ns
10% to 90% Values
Optical Fall Time
tf
-
-
2
ns
10% to 90% Values
RIN
-
-
-116
dB/Hz
TJ
-
-
1.2
ns
Measured with 223-1 PRBS with 72 ones and 72
zeros.
Symbol
Min
Typical
Max
Unit
Notes
Power Supply Current
ICC
-
-
180
mA
Transmitter Enable Voltage
VEN
0
-
0.8
V
Transmitter Disable Voltage
VD
2
-
Vcc
V
Data Input Current-Low
IIL
-200
-
-
µA
Data Input Current-High
IIH
-
-
200
µA
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
Relative Intensity Noise
Total Jitter
Transmitter Specifications
Parameter
Electrical
LUMINENTOIC.COM
Maximum current is specified at
Vcc= Maximum @ maximum temperature
These inputs are compatible with 10K, 10KH and
100K ECL and PECL inputs
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Sensitivity1
-
-
-
-32
dBm
C-13-155-F-SLC3A-12
Sensitivity1
-
-
-
-34
dBm
C-13-155-F-SLC5A-12
Maximum Input Power
Pin
-7
-
-
dBm
C-13-155-F-SLC3A-12
Maximum Input Power
Pin
-3
-
-
dBm
C-13-155-F-SLC5A-12
Signal Detect-Asserted
Pa
-
-
-32
dBm
Signal Detect-Asserted
Pa
-
-
-34
dbm
Signal Detect-Deasserted
Pd
-48
-
-
dBm
1
-
4
dB
1100
-
1600
nm
Symbol
Min
Typical
Max
Unit
Note
ICC
-
-
100
mA
The current excludes the output load current
VOL -Vcc
-2.0
-
-1.58
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
Signal Detect Output Voltage-Low
VSDL -Vcc
-2.0
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-0.74
V
Optical
Signal Detect-Hysteresis
Wavelength of Operation
Note1: Measured with
223-1
C-13-155-F-SLC3A-12
Measured on transition: low to high
C-13-155-F-SLC5A-12
Measured on transition: low to high
Measured on transition: high to low
PRBS/BER=10-10
Receiver Specifications
Parameter
Electrical
Power Supply Current
Data Output Voltage-Low
LUMINENTOIC.COM
These outputs are compatible with 10K,
10KH and 100KECL and LVPECL outputs
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Connection Diagram
PIN
Symbol
1
RxGND
Notes
Directly connect this pin to the receiver ground plane
2
RxVcc
+3.3V dc power for the receiver section
3
SD
Active high on this indicates a received optical signal(LVPECL/LVTTL)
4
RD-
Receiver Data Out Bar (LVPECL)
5
RD+
Receiver Data Out (LVPECL)
6
TxVcc
+3.3V dc power for the trasmitter section
7
TxGND
Directly connect this pin to the transmitter ground plane
8
Warnings
TxDIS
Transmitter disable (LVTTL)
9
TD+
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
Attaching Posts
LUMINENTOIC.COM
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Recommended Circuit Schematic
PHY DEVICE
TERMINATE AT
TRANSCEIVER INPUTS
Vcc(+3.3V)
Z=50�
TD-
LVPECL
100�
Z=50�
TD+
130�
1
3
TxGND
TxVcc
RD-
RD+
6
TxDIS
TD+
2
7
Tx Disable
SD
RxVcc
Rx
8
TD-
Tx
9
RxGND
10
4
130�
1�H
Vcc(+3.3V)
C2
C3
10�F
Vcc(+3.3V)
1�H
C1
5
LVTTL
RD+
Z=50�
LVPECL
100�
RD-
Z=50�
130�
Vcc(+3.3V)
130�
Z=50�
130�
SD
LVPECL
82�
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Package Diagram
C-13-155-F-SLC3(5)A-12
Units: mm (inches)



(0.039±0.002)
(0.070)


(0.400)



(0.020)

)
(0.386) +(
-(0.004)
(0.150)

(0.413)



(0.374)

(0.520)
 

)
(0.535) +(
-(0.004)
 )
(1.921) +(
-(0.008)

(0.280)


(0.246)
(0.200)
(0.700)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Ordering Information
Available Options:
C-13-155-F-SLC3A-12
C-13-155-F-SLC5A-12
C-13-155-F-SLC3A-12-G5
C-13-155-F-SLC5A-12-G5
Part numbering Definition:
C - 13 - 155 - F
- S LC TxPower Temperature Package
-12 -RoHS
• 13 = Wavelength 1310nm
• Communication protocol (155Mbps)
155 = PECL Signal Detection Output
• F = +3.3V SFF Transceiver, FP
• Single mode fiber
• Connector options
• Tx Power range
3 = -15 to -8 dBm
5 = -5 to 0 dBm
•Temperature
A = -40 to 85 ºC
• Package
Blank = Standard package
• -12 = Rubytech Customization
• Ordering Information
G5 = RoHS 5/6-compliant product (lead exemption)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS1776-Nov1207
Rev A.0
155 Mbps Single Mode SFF LC Transceiver
C-13-155-F-SLC3(5)A-12
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product described herein are free from patent, copyright, or intellectual property rights. Products described in this document
are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using
or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use
or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
10
LUMNDS1776-Nov1207
Rev A.0