Source C-15-622-TDFB3-SSC4AGR 622 mbps dfb laser single mode transceiver(lh) Datasheet

622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Features
• SC Duplex Single Mode Transceiver
• Industry Standard 1x9 Footprint
• Complies with SONET OC-12 SDH STM-4
• Single +3.3V/5V power supply
• Operatng Temperature Range 0 to 70ºC
• PECL Differential Inputs and Outputs
• TTL/LVTTL Signal Detection Output [C-1X-622C-TDFB(3)-SSC4]
• PECL/LVPECL Signal Detection Output [C-1X-622-TDFB(3)-SSC4]
• Wave Solderable and Aqueous Washable
• Uncooled laser diode with MQW sturcture
• Complies with Bellcore GR-468-CORE
• ATM 622 Mbps Link application
• SONET/SDH Equipment Interconnect application
• RoHS compliance available
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Vcc
0
6.0
V
C-1X-622(C)-TDFB-SSC4
Power Supply Voltage
Vcc
0
3.6
V
C-1X-622(C)-TDFB3-SSC4
Output Current
Iout
0
30
mA
Soldering Temperature
-
-
240
ºC
Operating temerature
Topr
0
70
ºC
Storage Temperature
Tstg
-40
85
ºC
Power Supply Voltage
Note
10 seconds on leads only
Recommended Operating Condition
Parameter
Symbol
Min.
Typ.
Max.
Unit
Power Supply Voltage
Vcc
Power Supply Voltage
Vcc
Operating Temperature (Case)
4.75
5
5.25
V
C-1X-622(C)-TDFB-SSC4
3.1
3.3
3.5
V
C-1X-622(C)-TDFB3-SSC4
Topr
-
0
-
70
ºC
-
622
-
Mbps
Symbol
Min
Typical
Max
Unit
Optical Transmit Power
Po
-3
-
+2
dBm
Output center Wavelength
λ
1280
1310
1335
nm
C-13-622(C)-TDFB(3)-SSC4
Output center Wavelength
λ
1480
1550
1580
nm
C-15-622(C)-TDFB(3)-SSC4
∆λ
-
-
1
nm
-20 dB width
Side Mode Suppression Ratio
Sr
30
35
-
dB
Extinction Ratio
ER
10
-
-
dB
Data Rate
Note
Transmitter Specifications
Parameter
Notes
Optical
Output Spectrum Width
Output Eye
Compliant with ITU recommendation G.957
Optical Rise Time
tr
-
-
Optical Fall Time
tf
-
-
RIN
-
-
TJ
-
-
0.55
ns
Relative Intensity Noise
Total Jitter
LUMINENTOIC.COM
1.2
ns
10% to 90% Values
1.2
ns
10% to 90% Values
-120
dB/Hz
Measured with 223-1 PRBS with 72 ones and
72 zeros.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Power Supply Current
ICC
-
-
150
mA
Data Input Current-Low
IIL
-350
-
-
µA
Data Input Current-High
IIH
-
-
350
µA
Notes
Electrical
Maximum current is specified at Vcc=
Maximum @ maximum temperature
Differential Input Voltage
VIH-VIL
300
-
-
mV
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
Symbol
Min
Typical
Max
Unit
-
-
-
-28
dBm
Maximum Input Power
Pin
-3
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-28
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-40
-
-
dBm
Measured on transition: high to low
-
3
-
dB
1100
-
1600
nm
Min
Typical
Max
Unit
Note
The current excludes the output load current
These inputs are compatible with 10K, 10KH
and 100K ECL and PECL inputs
Receiver Specifications
Parameter
Notes
Optical
Sensitivity
Signal Detect-Hysteresis
Wavelength of Operation
Measured with 223-1 PRBS,BER= 10-10
Receiver Specifications
Parameter
Symbol
Electrical
ICC
-
-
100
mA
Data Output Voltage-Low
VOL -Vcc
-2.0
-
-1.58
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
VSDL
-
-
0.5
V
VSDH
2.0
-
-
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-2.0
-
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-
-0.74
V
Power Supply Current
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
LUMINENTOIC.COM
These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs
C-1X-622C-TDFB(3)-SSC4
C-1X-622-TDFB(3)-SSC4
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Connection Diagram
1. (Rx GND)
2. (Rx +)
3. (Rx-)
4. (SD)
5. (Rx Vcc)
6. (Tx Vcc)
7. (TX-)
8. (TX+)
9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN
Symbol
1
RxGND
2
RD+
See recommended circuit schematic
3
RD-
See recommended circuit schematic
4
SD
5
RxVcc
6
TxVcc
7
TD-
See recommended circuit schematic
8
TD+
See recommended circuit schematic
9
TxGND
LUMINENTOIC.COM
Notes
Directly connect this pin to the receiver ground plane
Active high on this indicates a received optical signal
+3.3V/5V dc power for the receiver section
+3.3V/5V dc power for the transmitter section
Directly connect this pin to the transmitter ground plane
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Recommended Circuit Schematic
C-1X-622-TDFB(3)-SSC4
Tx Vcc
C5
Rx Vcc
9
7
8
6 5
4 3 2
1
R3
R1
R9
R5
C6
R7
TD +
RD +
TD -
RD -
Tx Vcc
SD
Rx Vcc
R4
R2
Notes +3.3V:
R1=R3=R5=R7=R9=130
R2=R4=R6=R8=R10=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
No internal
connection
R10
No internal
connection
Transceiver
Top view
R6
R8
L1
Notes +5V:
R1=R3=R5=R7=R9=82
R2=R4=R6=R8=R10=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
C1
C3
Vcc
Rx Vcc
L2
Tx Vcc
C2
C4
C-1X-622C-TDFB(3)-SSC4
Tx Vcc
C5
Rx Vcc
9
R1
7
8
6 5
4 3 2
1
R5
R3
C6
R7
TD +
RD +
TD -
RD -
Tx Vcc
SD
Rx Vcc
R2
R4
Notes +3.3V:
R1=R3=R5=R7=130
R2=R4=R6=R8=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
No internal
connection
Transceiver
Top view
Notes +5V:
R1=R3=R5=R7=82
R2=R4=R6=R8=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
R6
No internal
connection
R8
L1
Vcc
C3
C1
L2
C4
C2
Rx Vcc
Tx Vcc
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Package Diagram (10.4 mm SC transceiver assembly)
Top View
Front View
Side View
Rear View
Units: mm
Package Optiot:
Blank / A = Black Case
Package Diagram (9.8 mm SC transceiver assembly)
Front View
Top View
Units: mm
x8
Package Option:
B / E : Blue case
C / D : Black case
LUMINENTOIC.COM
Rear View
Side View
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Ordering Information
Available Options:
C-13-622-TDFB(3)-SSC4
C-13-622-TDFB(3)-SSC4A
C-13-622-TDFB(3)-SSC4B
C-13-622-TDFB(3)-SSC4C
C-13-622-TDFB(3)-SSC4D
C-13-622-TDFB(3)-SSC4E
C-15-622-TDFB(3)-SSC4
C-15-622-TDFB(3)-SSC4A
C-15-622-TDFB(3)-SSC4B
C-15-622-TDFB(3)-SSC4C
C-15-622-TDFB(3)-SSC4D
C-15-622-TDFB(3)-SSC4E
C-13-622C-TDFB(3)-SSC4
C-13-622C-TDFB(3)-SSC4A
C-13-622C-TDFB(3)-SSC4B
C-13-622C-TDFB(3)-SSC4C
C-13-622C-TDFB(3)-SSC4D
C-13-622C-TDFB(3)-SSC4E
C-15-622C-TDFB(3)-SSC4
C-15-622C-TDFB(3)-SSC4A
C-15-622C-TDFB(3)-SSC4B
C-15-622C-TDFB(3)-SSC4C
C-15-622C-TDFB(3)-SSC4D
C-15-622C-TDFB(3)-SSC4E
C-13-622-TDFB(3)-SSC4-G5
C-13-622-TDFB(3)-SSC4A-G5
C-13-622-TDFB(3)-SSC4B-G5
C-13-622-TDFB(3)-SSC4C-G5
C-13-622-TDFB(3)-SSC4D-G5
C-13-622-TDFB(3)-SSC4E-G5
C-15-622-TDFB(3)-SSC4-G5
C-15-622-TDFB(3)-SSC4A-G5
C-15-622-TDFB(3)-SSC4B-G5
C-15-622-TDFB(3)-SSC4C-G5
C-15-622-TDFB(3)-SSC4D-G5
C-15-622-TDFB(3)-SSC4E-G5
C-13-622C-TDFB(3)-SSC4-G5
C-13-622C-TDFB(3)-SSC4A-G5
C-13-622C-TDFB(3)-SSC4B-G5
C-13-622C-TDFB(3)-SSC4C-G5
C-13-622C-TDFB(3)-SSC4D-G5
C-13-622C-TDFB(3)-SSC4E-G5
C-15-622C-TDFB(3)-SSC4-G5
C-15-622C-TDFB(3)-SSC4A-G5
C-15-622C-TDFB(3)-SSC4B-G5
C-15-622C-TDFB(3)-SSC4C-G5
C-15-622C-TDFB(3)-SSC4D-G5
C-15-622C-TDFB(3)-SSC4E-G5
Part numbering Definition:
C - 1X - 622(C) - TDFB(3) - S SC TxPower Temperature and Package -RoHS
• Wavelength
13 = Wavelength 1310nm
15 = Wavelength 1550nm
• Communication protocol
(622 Mbps)
622 = PECL/VLPECL signal detection output
622C = TTL/LVTTL signal detection output
• TDFB= +5V DFB Transceiver
TDFB3= +3.3V DFB Transceiver
• Single mode fiber
• Connector options
SC
• Tx Power range
4 = -3 to +2 dBm
• Temperature range and package
Blank / A = Black case 10.4 mm
B / E = Blue case 9.8 mm
C / D = Black case 9.8 mm
• Ordering Information
Blank = RoHS non-compliant product
G5 = RoHS 5/6-compliant product (lead exemption)
GR = Full RoHS compliant product (no exemption)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS577-Jun0306
Rev A.1
622 Mbps DFB Laser Single Mode Transceiver(LH)
C-1X-622(C)-TDFB(3)-SSC4
Warnings
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notice
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS577-Jun0306
rev.A.0
Similar pages