Catalyst CAT40C00YETE13 128-bit serial eeprom Datasheet

CAT24C00
128-Bit Serial EEPROM
FEATURES
■ 400 kHz I2C bus compatible*
■ 1,000,000 Program/erase cycles
■ 1.8 to 5.5 volt operation
■ 100 year data retention
■ Low power CMOS technology
■ 8-pin DIP, 8-pin SOIC, 8 pin TSSOP and SOT-23
■ Self-timed write cycle with auto-clear
■ Industrial and Extended Temperature Ranges
DESCRIPTION
1
2
3
4
NC
NC
VSS
8
7
6
5
SOIC Package (J, W, GW)
VCC
NC
NC
NC
SCL
NC
SDA
VSS
1
SCL
VSS
SDA
5
NC
NC
NC
VSS
VCC
s
i
D
4
NC
PIN FUNCTIONS
Pin Name
8
7
6
5
VCC
NC
u
n
SCL
SDA
EXTERNAL LOAD
SENSE AMPS
SHIFT REGISTERS
DOUT
ACK
VCC
VSS
WORD ADDRESS
BUFFERS
COLUMN
DECODERS
TSSOP Package (U, Y, GY)
2
3
it
n
1
2
3
4
o
c
SOT-23 (TP, TB, GTB)
d
e
BLOCK DIAGRAM
DIP Package (P, L, GL)
NC
a
P
device power requirements. The device operates via the
I2C bus serial interface and is available in 8-pin DIP,
8-pin SOIC, 8-pin TSSOP and 5-pin SOT-23.
The CAT24C00 is a 128-bit Serial CMOS EEPROM
internally organized as 16 words of 8 bits each. Catalyst’s
advanced CMOS technology substantially reduces
PIN CONFIGURATION
t
r
1
2
3
4
8
7
6
5
SDA
VCC
NC
SCL
SDA
START/STOP
LOGIC
XDEC
CONTROL
LOGIC
Function
SDA
Serial Data/Address
SCL
Serial Clock
NC
No Connect
VCC
1.8 V to 5.5 V Power Supply
VSS
Ground
E2PROM
DATA IN STORAGE
HIGH VOLTAGE/
TIMING CONTROL
SCL
STATE COUNTERS
* Catalyst Semiconductor is licensed by Philips Corporation to carry the I2C Bus Protocol.
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. 1027, Rev. O
CAT24C00
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature Under Bias ................. –55°C to +125°C
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of
the device at these or any other conditions outside of those
listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for
extended periods may affect device performance and
reliability.
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground(1) ............ –2.0 V to VCC + 2.0 V
VCC with Respect to Ground ............. –2.0 V to +7.0 V
Package Power Dissipation
Capability (TA = 25°C) .................................. 1.0 W
t
r
Lead Soldering Temperature (10 seconds) ...... 300°C
Output Short Circuit Current(2) ....................... 100 mA
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Min.
NEND(3)
Endurance
TDR(3)
Data Retention
100
ESD Susceptibility
2000
Latch-up
100
VZAP
(3)
ILTH(3)(4)
VCC = 1.8 V to 5.5 V, unless otherwise specified.
Symbol
Parameter
ICC
Power Supply Current
ISB
o
c
ILI
Input Leakage Current
ILO
Output Leakage Current
VIL
Input Low Voltage
VIH
VOL1
VOL2
it
n
Standby Current (VCC = 5.0 V)
s
i
D
Input High Voltage
Units
Cycles/Byte
d
e
u
n
Test Conditions
a
P
Max.
1,000,000
D.C. OPERATING CHARACTERISTICS
(5)
Typ.
Min
Typ
Years
Volts
mA
Max
Units
fSCL = 400 kHz
2
mA
VIN = GND or VCC
1
µA
VIN = GND to VCC
10
µA
VOUT = GND to VCC
10
µA
–1
VCC x 0.3
V
VCC x 0.7
VCC + 0.5
V
Output Low Voltage (VCC = 3.0 V)
IOL = 3 mA
0.4
V
Output Low Voltage (VCC = 1.8 V)
IOL = 1.5 mA
0.5
V
Max
Units
CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5 V
Symbol
Parameter
Test Conditions
Min
Typ
CI/O(3)
Input/Output Capacitance (SDA)
VI/O = 0 V
8
pF
CIN(3)
Input Capacitance (SCL)
VIN = 0 V
6
pF
Note:
(1) The minimum DC input voltage is – 0.5 V. During transitions, inputs may undershoot to – 2.0 V for periods of less than 20 ns. Maximum
DC voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) These parameter are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from – 1 V to VCC + 1 V.
(5) Maximum standby current (ISB) = 10µA for the Extended Automotive temperature range.
Doc. No. 1027, Rev. O
2
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C00
A.C. CHARACTERISTICS
VCC = 1.8 V to 5.5 V, unless otherwise specified.
Read & Write Cycle Limits
Symbol
Parameter
1.8 V - 6.0 V
Min
Max
2.5 V - 6.0 V
Min
Max
FSCL
Clock Frequency
100
400
TI(1)
Noise Suppression Time
Constant at SCL, SDA Inputs
100
100
tAA
SCL Low to SDA Data Out
and ACK Out
3.5
tBUF(1)
Time the Bus Must be Free Before
a New Transmission Can Start
tHD:STA
Start Condition Hold Time
tLOW
Clock Low Period
4.7
tHIGH
Clock High Period
4
tSU:STA
Start Condition Setup Time
(for a Repeated Start Condition)
tHD:DAT
Data In Hold Time
tSU:DAT
Data In Setup Time
tR(1)
SDA and SCL Rise Time
tF
(1)
it
n
tSU:STO
Stop Condition Setup Time
tDH
Data Out Hold Time
Symbol
o
c
Parameter
s
i
D
4
0.6
4.7
d
e
u
n
0
SDA and SCL Fall Time
Power-Up Timing(1)(2)
1.2
50
1.2
0.6
0.6
t
r
kHz
ns
a
P
1
4.7
Units
µs
µs
µs
µs
µs
µs
0
ns
50
ns
1
0.3
µs
300
300
ns
4
0.6
µs
100
100
ns
Min
Typ
Max
Units
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
Max
Units
5
ms
Write Cycle Limits
Symbol
tWR
Parameter
Min
Typ
Write Cycle Time
interface circuits are disabled, SDA is allowed to remain
high, and the device does not respond to its slave
address.
The write cycle time is the time from a valid stop
condition of a write sequence to the end of the internal
program/erase cycle. During the write cycle, the bus
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3
Doc. No. 1027, Rev. O
CAT24C00
FUNCTIONAL DESCRIPTION
SDA: Serial Data/Address
The CAT24C00 bidirectional serial data/address pin is
used to transfer data into and out of the device. The SDA
pin is an open drain output and can be wire-ORed with
other open drain or open collector outputs.
The CAT24C00 supports the I2C Bus data transmission
protocol. This Inter-Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter
and any device receiving data to be a receiver. Data
transfer is controlled by the Master device which
generates the serial clock and all START and STOP
conditions for bus access. The CAT24C00 operates as
a Slave device. Both the Master and Slave devices can
operate as either transmitter or receiver, but the Master
device controls which mode is activated.
I2C BUS PROTOCOL
(1) Data transfer may be initiated only when the bus is
not busy.
SCL: Serial Clock
The CAT24C00 serial clock input pin is used to clock all
data transfers into or out of the device. This is an input
pin.
tHIGH
tLOW
tHD:STA
tLOW
tHD:DAT
it
n
SDA IN
tAA
SDA OUT
o
c
Figure 2. Write Cycle Timing
is
SCL
D
SDA
8TH BIT
BYTE n
d
e
tR
SCL
tSU:STA
a
P
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes
in the data line while the clock line is high will be
interpreted as a START or STOP condition.
PIN DESCRIPTIONS
Figure 1. Bus Timing tF
t
r
The following defines the features of the I2C bus protocol:
u
n
tSU:DAT
tDH
tSU:STO
tBUF
5020 FHD F03
ACK
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
5020 FHD F04
Figure 3. Start/Stop Timing
SDA
SCL
5020 FHD F05
START BIT
Doc. No. 1027, Rev. O
STOP BIT
4
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C00
The CAT24C00 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation,
it responds with an acknowledge after receiving each 8bit byte.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24C00 monitors the
SDA and SCL lines and will not respond until this
condition is met.
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
When the CAT24C00 is in a READ mode it transmits 8
bits of data, releases the SDA line, and monitors the line
for an acknowledge. Once it receives this acknowledge,
the CAT24C00 will continue to transmit data. If no
acknowledge is sent by the Master, the device terminates
data transmission and waits for a STOP condition.
DEVICE ADDRESSING
WRITE OPERATION
The bus Master begins a transmission by sending a
START condition. The Master then sends the address
of the particular slave device it is requesting. The four
most significant bits of the 8-bit slave address are fixed
as 1010 for the CAT24C00 (see Fig. 5). The next three
significant bits are "don't care" bits. The last bit of the
slave address specifies whether a Read or Write operation
is to be performed. When this bit is set to 1, a Read
operation is selected, and when set to 0, a Write operation
is selected.
Byte Write
STOP Condition
After the Master sends a START condition and the slave
address byte, the CAT24C00 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT24C00 then performs a Read or Write operation
depending on the state of the R/W bit.
it
n
o
c
Acknowledge
a
P
In the Write mode, the Master device sends the START
condition and the slave address information (with the R/
W bit set to zero) to the Slave device. After the Slave
generates an acknowledge, the Master sends the byte
address that is to be written into the address pointer of
the CAT24C00. After receiving another acknowledge
from the Slave, the Master device transmits the data
byte to be written into the addressed memory location.
The CAT24C00 acknowledges once more and the
Master generates the STOP condition, at which time the
device begins its internal programming cycle to
nonvolatile memory. While this internal cycle is in
progress, the device will not respond to any request
from the Master device.
d
e
u
n
After a write command, the internal address counter
will continue to point to the same address location
that was just written. If a stop bit is transmitted to the
device at any point in the write sequence before the
entire sequence is complete, then the command will
abort and no data will be written. If more than eight
After a successful data transfer, each receiving device is
required to generate an acknowledge. The
Acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8 bits
of data.
s
i
D
t
r
Figure 4. Acknowledge Timing
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACKNOWLEDGE
5020 FHD F06
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. 1027, Rev. O
CAT24C00
Figure 5. Slave Address Bits
CAT24C00
1
0
1
bits are transmitted before the stop bit is sent, then
the device will clear the previously loaded byte and
begin loading the data buffer again. If more than one
data byte is transmitted to the device and a stop bit
is sent before a full eight bits of data have been
transmitted, then the write command will abort and
no data will be written.
The disabling of the inputs can be used to take advantage
of the typical write cycle time. Once the stop condition
is issued to indicate the end of the host’s write operation,
the CAT24C00 initiates the internal write cycle. ACK
polling can be initiated immediately. This involves
issuing the start condition followed by the slave address
for a write operation. If the CAT24C00 is still busy with
the write operation, no ACK will be returned. If the
CAT24C00 has completed the write operation, an ACK
will be returned and the host can then proceed with the
next read or write operation.
s
i
D
o
c
X
X
t
r
R/W
d
e
a
P
Selective READ operations allow the Master device to
select at random any memory location for a READ
operation. The Master device first performs a ‘dummy’
write operation by sending the START condition, slave
address and byte address of the location it wishes to
read. After the CAT24C00 acknowledges the word
address, the Master device resends the START condition
and the slave address, this time with the R/W bit is set to
one. The CAT24C00 then responds with its acknowledge
and sends the 8-bit byte requested. To end the Read
Operation the master device does not send an
acknowledge but will generate a STOP condition.
u
n
The READ operation for the CAT24C00 is initiated in the
same manner as the write operation with the one
exception that the R/W bit is set to a one. Three different
READ operations are possible: Immediate Address
READ, Selective READ and Sequential READ.
Sequential Read
The Sequential READ operation can be initiated by
either the immediate Address READ or Selective READ
operations. After the CAT24C00 sends initial 8-bit byte
requested, the Master will respond with an acknowledge
which tells the device it requires more data. The
CAT24C00 will continue to output an 8-bit byte for each
acknowledge sent by the Master. The operation is
terminated when the Master fails to respond with an
acknowledge, thus sending the STOP condition.
The data being transmitted from the CAT24C00 is
outputted sequentially with data from address N followed
by data from address N+1. The READ operation address
counter increments all of the CAT24C00 address bits so
that the entire memory array can be read during one
operation. If more than 16 bytes are read out, the counter
will “wrap around” and continue to clock out data bytes.
Immediate Address Read
The device’s address counter contains the address of
the last byte accessed, incremented by one. In other
words, if the last READ access was to address N, the
READ immediately following would access data from
address N+1. If N=15, then the counter will 'wrap around'
to address 0 and continue to clock out data.
Doc. No. 1027, Rev. O
X
Selective Read
it
n
Acknowledge Polling
READ OPERATIONS
0
6
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C00
Figure 6. Byte Write Timing
S
T
A
R
T
BUS ACTIVITY:
MASTER
SDA LINE
SLAVE
ADDRESS
BYTE
ADDRESS
DATA
P
S
A
C
K
A
C
K
A
C
K
Figure 7. Immediate Address Read Timing
S
T
BUS ACTIVITY: A
MASTER R
T
S
T
O
P
SLAVE
ADDRESS
d
e
SDA LINE S
P
A
C
K
it
n
8
SCL
8TH BIT
SDA
DATA OUT
o
c
Figure 8. Selective Read Timing
is
BUS ACTIVITY:
MASTER
D
SDA LINE
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
DATA
u
n
9
N
O
A
C
K
NO ACK
S
T
A
R
T
BYTE
ADDRESS (n)
S
t
r
a
P
STOP
S
T
O
P
SLAVE
ADDRESS
S
A
C
K
P
A
C
K
A
C
K
DATA n
N
O
A
C
K
Figure 9. Sequential Read Timing
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
DATA n
DATA n+1
DATA n+2
S
T
O
P
DATA n+x
SDA LINE
P
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. 1027, Rev. O
CAT24C00
ORDERING INFORMATION
Prefix
Device #
Suffix
24C00
CAT
Optional
Company ID
J
X
I
Temperature Range
I = Industrial (-40°C to 85°C)
E = Extended (-40°C to 125°C)
Product Number
24C00: 128 Bit
Package
P: PDIP
J : SOIC (JEDEC)
U: TSSOP
TP: SOT23
L : PDIP (Lead free, Halogen free)
TB: SOT23 (Lead free, Halogen free)
W: SOIC (Lead free, Halogen free)
Y: TSSOP (Lead free, Halogen free)
GL: PDIP (Lead-free, Halogen-free, NiPdAu lead plating)
GTB: SOT23 (Lead-free, Halogen-free, NiPdAu lead plating)
GW: SOIC (Lead-free, Halogen-free, NiPdAu lead plating)
GY: TSSOP (Lead-free, Halogen-free, NiPdAu lead plating)
it
n
t
r
Tape & Reel
Operating Voltage
Blank: 1.8 V - 5.5 V
d
e
u
n
Rev B(2)
TE13
a
P
Die Revision
Notes:
(1) The device used in the above example is a CAT24C00JI-TE13 (SOIC, Industrial Temperature, 1.8 Volt to 5.5 Volt Operating Voltage,
Tape & Reel)
(2) Product die revision letter is marked on top of the package as a suffix to the production date code (e.g. AYWWB). For additional
information, please contact your Catalyst sales office.
o
c
s
i
D
Doc. No. 1027, Rev. O
8
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CAT24C00
REVISION HISTORY
Date
Rev.
Reason
9/24/2003
H
Eliminated commercial temperature range class
Updated marking
10/30/2003
I
Eliminated automotive temperature reange
12/9/2003
J
Changed Industrial temp range designation from "Blank" to "I"
12/23/2003
K
Eliminatd Commercial and Automotive temp ranges from Features on
front page of data sheet
12/29/2003
L
Moved DC Operating Characteristics typ numbers for VOL1 and VOL2 to
max column
Changed 1.8V to 1.8V - 6.0V for AC Characteristics
7/7/2004
M
Added Die Revision to Ordering Information
7/27/2004
N
Updated DC Operating Characteristics chart and notes
07/12/2005
O
Upate Rekiability Characteristics table
d
e
Update Ordering Information
o
c
it
n
s
i
D
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
u
n
9
t
r
a
P
Changed 4.5V - 5.5V to 2.5V - 6.0V for AC Characteristics
Doc. No. 1027, Rev. O
DPP ™
AE2 ™
it
n
MiniPot™
d
e
u
n
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
t
r
a
P
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents
issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
o
c
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a
situation where personal injury or death may occur.
s
i
D
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate
typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
1250 Borregas Avenue
Sunnyvale, CA 94089
Phone: 408.542.1000
Fax: 408.542.1200
www.caalyst-semiconductor.com
Publication #:
Revison:
Issue date:
1027
O
7/12/05
Similar pages