ON CAT5419YI00 Dual digital potentiometer (pot) Datasheet

CAT5419
Dual Digital
Potentiometer (POT)
with 64 Taps
and 2‐wire Interface
http://onsemi.com
Description
The CAT5419 is two digital POTs integrated with control logic and
16 bytes of NVRAM memory.
A separate 6-bit control register (WCR) independently controls the
wiper tap position for each digital POT. Associated with each wiper
control register are four 6-bit non-volatile memory data registers (DR)
used for storing up to four wiper settings. Writing to the wiper control
register or any of the non-volatile data registers is via a 2-wire serial
bus (I2C-like). On power-up, the contents of the first data register
(DR0) for each of the two potentiometers is automatically loaded into
its respective wiper control registers (WCR).
The Write Protection (WP) pin protects against inadvertent
programming of the data register.
The CAT5419 can be used as a potentiometer or as a two terminal,
variable resistor. It is intended for circuit level or system level
adjustments in a wide variety of applications.










SOIC−24
W SUFFIX
CASE 751BK
PIN CONNECTIONS
VCC
NC
1
RL0
NC
RH0
NC
RW0
NC
A0
A2
Features




TSSOP24
Y SUFFIX
CASE 948AR
Two Linear-taper Digital Potentiometers
64 Resistor Taps per Potentiometer
End to End Resistance 2.5 kW, 10 kW, 50 kW or 100 kW
Potentiometer Control and Memory Access via 2-wire Interface
(I2C like)
Low Wiper Resistance, Typically 80 W
Four Non-volatile Wiper Settings for Each Potentiometer
Recall of Wiper Settings at Power Up
2.5 to 6.0 Volt Operation
Standby Current less than 1 mA
1,000,000 Nonvolatile WRITE Cycles
100 Year Nonvolatile Memory Data Retention
24-lead SOIC and 24-lead TSSOP
Write Protection for Data Register
These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
WP
SDA
CAT5419
NC
A3
A1
SCL
RL1
NC
RH1
NC
RW1
NC
GND
NC
SOIC−24 (W)
(Top View)
SDA
A1
RL1
RH1
RW1
GND
NC
NC
NC
NC
SCL
A3
1
CAT5419
WP
A2
RW0
RH0
RL0
VCC
NC
NC
NC
NC
A0
NC
TSSOP24 (Y)
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
 Semiconductor Components Industries, LLC, 2013
July, 2013 − Rev. 11
1
Publication Order Number:
CAT5419/D
CAT5419
RH0
SCL
SDA
RH1
WIPER
CONTROL
REGISTERS
2−WIRE BUS
INTERFACE
RW0
RW1
WP
A0
A1
A2
A3
NONVOLATILE
DATA
REGISTERS
CONTROL
LOGIC
RL0
Figure 1. Functional Diagram
RL1
PIN DESCRIPTIONS
SCL: Serial Clock
Table 1. PIN CONNECTIONS
The CAT5419 serial clock input pin is used to clock all
data transfers into or out of the device.
Pin
SOIC
Pin
TSSOP
Name
SDA: Serial Data
1
19
Supply Voltage
The CAT5419 bidirectional serial data pin is used to
transfer data into and out of the device. The SDA pin is an
open drain output and can be wire-OR’d with the other open
drain or open collector outputs.
VCC
2
20
RL0
Low Reference Terminal
for Potentiometer 0
3
21
RH0
High Reference Terminal
for Potentiometer 0
4
22
RW0
Wiper Terminal for
Potentiometer 0
5
23
A2
Device Address
6
24
WP
Write Protection
7
1
SDA
Serial Data Input/Output
8
2
A1
Device Address
9
3
RL1
The RH and RL pins are equivalent to the terminal
connections on a mechanical potentiometer.
Low Reference Terminal
for Potentiometer 1
10
4
RH1
High Reference Terminal
for Potentiometer 1
RW: Wiper
11
5
RW1
Wiper Terminal for
Potentiometer 1
12
6
GND
Ground
13
7
NC
No Connect
14
8
NC
No Connect
15
9
NC
No Connect
16
10
NC
No Connect
17
11
SCL
Bus Serial Clock
18
12
A3
Device Address
19
13
NC
No Connect
20
14
A0
Device Address, LSB
21
15
NC
No Connect
22
16
NC
No Connect
23
17
NC
No Connect
24
18
NC
No Connect
A0, A1, A2, A3: Device Address Inputs
These inputs set the device address when addressing
multiple devices. A total of sixteen devices can be addressed
on a single bus. A match in the slave address must be made
with the address input in order to initiate communication
with the CAT5419.
RH, RL: Resistor End Points
The RW pins are equivalent to the wiper terminal of a
mechanical potentiometer.
WP: Write Protect Input
The WP pin when tied low prevents non-volatile writes to
the data registers (change of wiper control register is
allowed) and when tied high or left floating normal
read/write operations are allowed. See page 8, Write
Protection for more details.
http://onsemi.com
2
Function
CAT5419
DEVICE OPERATION
The CAT5419 is two resistor arrays integrated with 2wire
serial interface logic, four 6-bit wiper control registers and
sixteen 6-bit, non-volatile memory data registers. Each
resistor array contains 63 separate resistive elements
connected in series. The physical ends of each array are
equivalent to the fixed terminals of a mechanical
potentiometer (RH and RL). RH and RL are symmetrical and
may be interchanged. The tap positions between and at the
ends of the series resistors are connected to the output wiper
terminals (RW) by a CMOS transistor switch. Only one tap
point for each potentiometer is connected to its wiper
terminal at a time and is determined by the value of the wiper
control register. Data can be read or written to the wiper
control registers or the non-volatile memory data registers
via the 2-wire bus. Additional instructions allow data to be
transferred between the wiper control registers and each
respective potentiometer’s non-volatile data registers. Also,
the device can be instructed to operate in an
“increment/decrement” mode.
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameters
Temperature Under Bias
Storage Temperature Range
Ratings
Units
−55 to +125
C
−65 to +150
C
−2.0 to VCC +2.0
V
−2.0 to +7.0
V
Package Power Dissipation Capability (TA = 25C)
1.0
W
Lead Soldering Temperature (10 s)
300
C
Wiper Current
12
mA
Voltage to any Pins with Respect to VSS (Notes 1, 2)
VCC with Respect to GND
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The minimum DC input voltage is −0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods of less than 20 ns.
2. Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to VCC + 1 V.
Table 3. RECOMMENDED OPERATING CONDITIONS
Parameters
Ratings
Units
VCC
+2.5 to 6.0
V
Industrial Temperature
−40 to +85
C
http://onsemi.com
3
CAT5419
Table 4. POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
RPOT
Potentiometer Resistance (−00)
100
kW
RPOT
Potentiometer Resistance (−50)
50
kW
RPOT
Potentiometer Resistance (−10)
10
kW
RPOT
Potentiometer Resistance (−25)
2.5
Potentiometer Resistance Tolerance
kW
20
%
1
%
50
mW
6
mA
300
W
150
W
VCC
V
RPOT Matching
Power Rating
25C, each pot
IW
Wiper Current
RW
Wiper Resistance
IW = 3 mA @ VCC = 3 V
RW
Wiper Resistance
IW = 3 mA @ VCC = 5 V
VTERM
VN
Voltage on any RH or RL Pin
VSS = 0 V
Noise
80
GND
(Note 3)
TBD
nV/Hz
1.6
%
Resolution
Absolute Linearity (Note 4)
RW(n)(actual)−R(n)(expected)
(Note 7)
1
LSB
(Note 6)
Relative Linearity (Note 5)
RW(n+1)−[RW(n)+LSB]
(Note 7)
0.2
LSB
(Note 6)
TCRPOT
Temperature Coefficient of RPOT
(Note 3)
TCRATIO
Ratiometric Temp. Coefficient
(Note 3)
CH/CL/CW
Potentiometer Capacitances
(Note 3)
10/10/25
pF
RPOT = 50 kW (Note 3)
0.4
MHz
fc
Frequency Response
ppm/C
300
20
ppm/C
3. This parameter is tested initially and after a design or process change that affects the parameter.
4. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
potentiometer.
5. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer.
It is a measure of the error in step size.
6. LSB = RTOT / 63 or (RH − RL) / 63, single pot
7. n = 0, 1, 2, ..., 63
Table 5. D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Symbol
Parameter
ICC
Power Supply Current
ISB
Standby Current (VCC = 5 V)
ILI
Input Leakage Current
ILO
Output Leakage Current
VIL
Input Low Voltage
VIH
Input High Voltage
VOL1
Test Conditions
Max
Units
fSCL = 400 kHz
1
mA
VIN = GND or VCC; SDA Open
1
mA
VIN = GND to VCC
10
mA
VOUT = GND to VCC
10
mA
−1
VCC x 0.3
V
VCC x 0.7
VCC + 1.0
V
0.4
V
Output Low Voltage (VCC = 3 V)
Min
IOL = 3 mA
Table 6. PIN CAPACITANCE (Note 8)
(Applicable over recommended operating range from TA = 25C, f = 1.0 MHz, VCC = +5.0 V (unless otherwise noted).)
Symbol
Test Conditions
Min
Typ
Max
Units
Conditions
CI/O
Output Capacitance (SDA)
8
pF
VI/O = 0 V
CIN
Input Capacitance (A0, A1, A2, A3, SCL, WP)
6
pF
VIN = 0 V
http://onsemi.com
4
CAT5419
Table 7. A.C. CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Parameter
Max
Units
Clock Frequency
400
kHz
Noise Suppression Time Constant at SCL, SDA Inputs
50
ns
SLC Low to SDA Data Out and ACK Out
0.9
ms
Symbol
fSCL
TI (Note 8)
tAA
tBUF (Note 8)
Min
Typ
Time the bus must be free before a new transmission can start
1.2
ms
Start Condition Hold Time
0.6
ms
tLOW
Clock Low Period
1.2
ms
tHIGH
Clock High Period
0.6
ms
tSU:STA
Start Condition Setup Time (for a Repeated Start Condition)
0.6
ms
tHD:DAT
Data in Hold Time
0
ns
tSU:DAT
Data in Setup Time
100
tHD:STA
ns
tR (Note 8)
SDA and SCL Rise Time
0.3
ms
tF (Note 8)
SDA and SCL Fall Time
300
ns
tSU:STO
tDH
Stop Condition Setup Time
0.6
ms
Data Out Hold Time
50
ns
Table 8. POWER UP TIMING (Note 8) (Over recommended operating conditions unless otherwise stated.)
Symbol
Parameter
Min
Typ
Max
Units
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
Max
Units
5
ms
8. This parameter is tested initially and after a design or process change that affects the parameter.
Table 9. WRITE CYCLES LIMITS (Note 9)
Parameter
Symbol
tWR
Write Cycle Time
9. The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write
cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address.
Table 10. RELIABILITY CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Symbol
Parameter
Reference Test Method
Min
Typ
Max
Units
NEND (Note 10)
Endurance
MIL−STD−883, Test Method 1033
1,000,000
Cycles/Byte
TDR (Note 10)
Data Retention
MIL−STD−883, Test Method 1008
100
Years
VZAP (Note 10)
ESD Susceptibility
MIL−STD−883, Test Method 3015
2,000
Volts
ILTH (Notes 10, 11)
Latch-up
100
mA
JEDEC Standard 17
10. This parameter is tested initially and after a design or process change that affects the parameter.
11. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
http://onsemi.com
5
CAT5419
tF
tHIGH
tLOW
tR
tLOW
SCL
tSU:STA
tHD:DAT
tHD:STA
tSU:STO
tSU:DAT
SDA IN
tBUF
tDH
tAA
SDA OUT
Figure 2. Bus Timing
SCL
8TH BIT
SDA
ACK
BYTE n
tWR
STOP
CONDITION
START
CONDITION
Figure 3. Write Cycle Timing
SDA
SCL
START BIT
STOP BIT
Figure 4. Start/Stop Timing
http://onsemi.com
6
ADDRESS
CAT5419
SERIAL BUS PROTOCOL
The following defines the features of the 2-wire bus
protocol:
1. Data transfer may be initiated only when the bus is
not busy.
2. During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock is high
will be interpreted as a START or STOP condition.
Therefore, the CAT5419 will be considered a slave device
in all applications.
The device controlling the transfer is a master, typically a
processor or controller, and the device being controlled is the
slave. The master will always initiate data transfers and
provide the clock for both transmit and receive operations.
STOP Condition
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of SDA
when SCL is HIGH. The CAT5419 monitors the SDA and
SCL lines and will not respond until this condition is met.
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
Acknowledge
The bus Master begins a transmission by sending a
START condition. The Master then sends the address of the
particular slave device it is requesting. The four most
significant bits of the 8-bit slave address are fixed as 0101
for the CAT5419 (see Figure 5). The next four significant
bits (A3, A2, A1, A0) are the device address bits and define
which device the Master is accessing. Up to sixteen devices
may be individually addressed by the system. Typically,
+5 V and ground are hard-wired to these pins to establish the
device’s address.
After the Master sends a START condition and the slave
address byte, the CAT5419 monitors the bus and responds
with an acknowledge (on the SDA line) when its address
matches the transmitted slave address.
SCL FROM
MASTER
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledging
device pulls down the SDA line during the ninth clock cycle,
signaling that it received the 8 bits of data.
The CAT5419 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8-bit
byte.
When the CAT5419 is in a READ mode it transmits 8 bits
of data, releases the SDA line, and monitors the line for an
acknowledge. Once it receives this acknowledge, the
CAT5419 will continue to transmit data. If no acknowledge
is sent by the Master, the device terminates data transmission
and waits for a STOP condition.
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
ACKNOWLEDGE
START
Figure 5. Acknowledge Timing
Write Operations
from the Slave, the Master device transmits the data to be
written into the selected register. The CAT5419
acknowledges once more and the Master generates the
STOP condition, at which time if a nonvolatile data register
is being selected, the device begins an internal programming
cycle to non-volatile memory. While this internal cycle is in
progress, the device will not respond to any request from the
Master device.
In the Write mode, the Master device sends the START
condition and the slave address information to the Slave
device. After the Slave generates an acknowledge, the
Master sends the instruction byte that defines the requested
operation of CAT5419. The instruction byte consist of a
four-bit opcode followed by two register selection bits and
two pot selection bits. After receiving another acknowledge
http://onsemi.com
7
CAT5419
Acknowledge Polling
Write Protection
The disabling of the inputs can be used to take advantage
of the typical write cycle time. Once the stop condition is
issued to indicate the end of the host’s write operation, the
CAT5419 initiates the internal write cycle. ACK polling can
be initiated immediately. This involves issuing the start
condition followed by the slave address. If the CAT5419 is
still busy with the write operation, no ACK will be returned.
If the CAT5419 has completed the write operation, an ACK
will be returned and the host can then proceed with the next
instruction operation.
The Write Protection feature allows the user to protect
against inadvertent programming of the non-volatile data
registers. If the WP pin is tied to LOW, the data registers are
protected and become read only. Similarly, WP pin going
LOW after Start will interrupt non-volatile write to data
registers, while WP pin going LOW after internal write
cycle has started will have no effect on any write operation.
The CAT5419 will accept both slave addresses and
instructions, but the data registers are protected from
programming by the device’s failure to send an
acknowledge after data is received.
CAT5419
0
1
0
1
A3
A2
A1
A0
* A0, A1, A2 and A3 correspond to pin A0, A1, A2 and A3 of the device.
** A0, A1, A2 and A3 must compare to its corresponding hard wired input pins.
Figure 6. Slave Address Bits
SDA LINE
SLAVE
ADDRESS
Fixed
op code
BUS ACTIVITY:
MASTER
S
T
A
R
T
Variable
Data Register
Address
Pot/WCR
Address
INSTRUCTION
BYTE
S
T
O
P
DR1 WCR DATA
P
S
A
C
K
A
C
K
A
C
K
Figure 7. Write Timing
INSTRUCTIONS AND REGISTER DESCRIPTION
Instructions
Instruction Byte
The next byte sent to the CAT5419 contains the
instruction and register pointer information. The four most
significant bits used provide the instruction opcode I [3:0].
The R1 and R0 bits point to one of the four data registers of
each associated potentiometer. The least two significant bits
point to one of two Wiper Control Registers. The format is
shown in Figure 9.
Slave Address Byte
The first byte sent to the CAT5419 from the master/
processor is called the Slave Address Byte. The most
significant four bits of the slave address are a device type
identifier. These bits for the CAT5419 are fixed at 0101[B]
(refer to Figure 8).
The next four bits, A3 − A0, are the internal slave address
and must match the physical device address which is defined
by the state of the A3 − A0 input pins for the CAT5419 to
successfully continue the command sequence. Only the
device which slave address matches the incoming device
address sent by the master executes the instruction. The A3
− A0 inputs can be actively driven by CMOS input signals
or tied to VCC or VSS.
Table 11. DATA REGISTER SELECTION
http://onsemi.com
8
Data Register Selected
R1
R0
DR0
0
0
DR1
0
1
DR2
1
0
DR3
1
1
CAT5419
Device Type Identifier
ID3
0
ID2
ID1
1
0
Slave Address
ID0
A3
A2
A1
A0
1
(LSB)
(MSB)
Figure 8. Identification Byte Format
Data Register
Selection
Instruction
Opcode
I3
I2
I1
I0
R1
R0
(MSB)
WCR/Pot Selection
0
P0
(LSB)
Figure 9. Instruction Byte Format
WIPER CONTROL AND DATA REGISTERS
Wiper Control Register (WCR)
Data can also be transferred between any of the four Data
Registers and the associated Wiper Control Register. Any
data changes in one of the Data Registers is a non-volatile
operation and will take a maximum of 5 ms.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can be used
as standard memory locations for system parameters or user
preference data.
The CAT5419 contains two 6-bit Wiper Control
Registers, one for each potentiometer. The Wiper Control
Register output is decoded to select one of 64 switches along
its resistor array. The contents of the WCR can be altered in
four ways: it may be written by the host via Write Wiper
Control Register instruction; it may be written by
transferring the contents of one of four associated Data
Registers via the XFR Data Register instruction, it can be
modified one step at a time by the Increment/Decrement
instruction (see Instruction section for more details).
Finally, it is loaded with the content of its data register zero
(DR0) upon power-up.
The Wiper Control Register is a volatile register that loses
its contents when the CAT5419 is powered-down. Although
the register is automatically loaded with the value in DR0
upon power-up, this may be different from the value present
at power-down.
Instructions
Four of the nine instructions are three bytes in length.
These instructions are:
 Read Wiper Control Register – read the current wiper
position of the selected potentiometer in the WCR
 Write Wiper Control Register – change current wiper
position in the WCR of the selected potentiometer
 Read Data Register – read the contents of the selected
Data Register
 Write Data Register – write a new value to the
selected Data Register.
Data Registers (DR)
Each potentiometer has four 6-bit non-volatile Data
Registers. These can be read or written directly by the host.
http://onsemi.com
9
CAT5419
Table 12. INSTRUCTION SET (Note: 1/0 = data is one or zero)
Instruction Set
I3
I2
I1
I0
R1
R0
0
WCR0/ P0
Read Wiper Control
Register
1
0
0
1
0
0
0
1/0
Read the contents of the Wiper Control
Register pointed to by P0
Write Wiper Control
Register
1
0
1
0
0
0
0
1/0
Write new value to the Wiper Control
Register pointed to by P0
Read Data Register
1
0
1
1
1/0
1/0
0
1/0
Read the contents of the Data Register
pointed to by P0 and R1−R0
Write Data Register
1
1
0
0
1/0
1/0
0
1/0
Write new value to the Data Register
pointed to by P0 and R1−R0
XFR Data Register to
Wiper Control Register
1
1
0
1
1/0
1/0
0
1/0
Transfer the contents of the Data
Register pointed to by P0 and R1−R0 to
its associated Wiper Control Register
XFR Wiper Control
Register to Data Register
1
1
1
0
1/0
1/0
0
1/0
Transfer the contents of the Wiper
Control Register pointed to by P0 to the
Data Register pointed to by R1−R0
Gang XFR Data Registers
to Wiper Control Registers
0
0
0
1
1/0
1/0
0
0
Transfer the contents of the Data
Registers pointed to by R1−R0 of both
pots to their respective Wiper Control
Registers
Gang XFR Wiper Control
Registers to Data Register
1
0
0
0
1/0
1/0
0
0
Transfer the contents of both Wiper
Control Registers to their respective data
Registers pointed to by R1−R0 of both
four pots
Increment/Decrement
Wiper Control Register
0
0
1
0
0
0
0
1/0
Instruction
The basic sequence of the three byte instructions is
illustrated in Figure 11. These three-byte instructions
exchange data between the WCR and one of the Data
Registers. The WCR controls the position of the wiper. The
response of the wiper to this action will be delayed by tWRL.
A transfer from the WCR (current wiper position), to a Data
Register is a write to non-volatile memory and takes a
maximum of tWR to complete. The transfer can occur
between one of the potentiometers and one of its associated
registers; or the transfer can occur between all
potentiometers and one associated register.
Four instructions require a two-byte sequence to
complete, as illustrated in Figure 10. These instructions
transfer data between the host/processor and the CAT5419;
either between the host and one of the data registers or
directly between the host and the Wiper Control Register.
These instructions are:
 XFR Data Register to Wiper Control Register
This transfers the contents of one specified Data
Register to the associated Wiper Control Register.
 XFR Wiper Control Register to Data Register
This transfers the contents of the specified Wiper
Control Register to the specified associated Data
Register.
Operation
Enable Increment/decrement of the
Control Latch pointed to by P0
 Global XFR Data Register to Wiper Control

Register
This transfers the contents of all specified Data Registers
to the associated Wiper Control Registers.
Global XFR Wiper Counter Register to Data
Register
This transfers the contents of all Wiper Control Registers
to the specified associated Data Registers.
Increment/Decrement Command
The final command is Increment/Decrement (Figure 6
and 12). The Increment/Decrement command is different
from the other commands. Once the command is issued and
the CAT5419 has responded with an acknowledge, the
master can clock the selected wiper up and/or down in one
segment steps; thereby providing a fine tuning capability to
the host. For each SCL clock pulse (tHIGH) while SDA is
HIGH, the selected wiper will move one resistor segment
towards the RH terminal. Similarly, for each SCL clock
pulse while SDA is LOW, the selected wiper will move one
resistor segment towards the RL terminal.
See Instructions format for more detail.
http://onsemi.com
10
CAT5419
0
SDA
1
0
1
S ID3 ID2 ID1 ID0 A3 A2 A1 A0
T
A
Internal
Device ID
R
Address
T
A
C
K
I3
I2
I1
A
C
K
Register Pot/WCR
Address Address
I0 R1 R0 0 P0
Instruction
Opcode
S
T
O
P
Figure 10. Two-byte Instruction Sequence
SDA
0
1
0
1
S ID3 ID2 ID1 ID0 A3 A2 A1 A0 A I3 I2 I1 I0 R1 R0 0 P0 A D7 D6 D5 D4 D3 D2 D1 D0
C
T
C
K
K
A
Device ID
Internal
WCR[7:0]
Instruction
Pot/WCR
R
Data
Address
or
Opcode
Register Address
T
Data Register D[7:0]
Address
A S
C T
K O
P
Figure 11. Three-byte Instruction Sequence
0
SDA
S
T
A
R
T
1
0
1
ID3 ID2 ID1 ID0 A3 A2 A1 A0
Device ID
Internal
Address
A
C
K
I3
I2
I1
I0
Instruction
Opcode
A
C
K
Data Pot/WCR
Register Address
Address
R1 R0
0
P0
I
N
C
1
I
N
C
2
Figure 12. Increment/Decrement Instruction Sequence
INC/DEC
Command
Issued
tWRID
SCL
SDA
RW
Voltage Out
Figure 13. Increment/Decrement Timing Limits
http://onsemi.com
11
I
N
C
n
D
E
C
1
D
E
C
n
S
T
O
P
CAT5419
INSTRUCTION FORMAT
Table 13. READ WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
0
1
0
0
0
P0
A
C
K
DATA
7
6
0
0
5
4
3
2
1
0
A
C
K
S
T
O
P
A
C
K
S
T
O
P
A
C
K
S
T
O
P
A
C
K
S
T
O
P
Table 14. WRITE WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
1
0
0
0
0
P0
A
C
K
DATA
7
6
0
0
5
4
3
2
1
0
Table 15. READ DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
1
1
R1
R0
0
P0
A
C
K
DATA
7
6
0
0
5
4
3
2
1
0
Table 16. WRITE DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
0
0
R1
R0
0
P0
A
C
K
DATA
7
6
0
0
5
4
Table 17. GLOBAL TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
0
0
0
1
R1
R0
0
0
A
C
K
S
T
O
P
Table 18. GLOBAL TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
0
0
R1
R0
0
0
A
C
K
S
T
O
P
Table 19. TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
1
0
R1
R0
http://onsemi.com
12
0
P0
A
C
K
S
T
O
P
3
2
1
0
CAT5419
Table 20. TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
0
1
R1
R0
0
P0
A
C
K
S
T
O
P
Table 21. INCREMENT (I)/DECREMENT (D) WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
NOTE:
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
0
0
1
0
0
0
0
P0
A
C
K
DATA
I/D
I/D
...
I/D
I/D
S
T
O
P
Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after a STOP has been issued.
Table 22. ORDERING INFORMATION
Orderable Part Number
Resistance (kW)
CAT5419WI−25−T1
2.5
CAT5419WI−10−T1
10
CAT5419WI−50−T1
50
CAT5419WI−00−T1
100
CAT5419YI−25−T2
2.5
CAT5419YI−10−T2
10
CAT5419YI−50−T2
50
CAT5419YI−00−T2
100
CAT5419WI25
2.5
CAT5419WI10
10
CAT5419WI50
50
CAT5419WI00
100
CAT5419YI25
2.5
CAT5419YI10
10
CAT5419YI50
50
CAT5419YI00
100
Lead Finish
Package
Shipping†
SOIC−24
(Pb-Free)
1,000 / Tape & Reel
TSSOP24
(Pb-Free)
2,000 / Tape & Reel
SOIC−24
(Pb-Free)
31 Units / Tube
TSSOP24
(Pb-Free)
62 Units / Tube
Matte-Tin
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
12. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com.
13. All packages are RoHS-compliant (Pb-Free, Halogen Free).
14. The standard lead finish is Matte-Tin.
http://onsemi.com
13
CAT5419
PACKAGE DIMENSIONS
SOIC−24, 300 mils
CASE 751BK
ISSUE O
E1
SYMBOL
MIN
A
2.35
2.65
A1
0.10
0.30
A2
2.05
2.55
b
0.31
0.51
c
0.20
0.33
D
15.20
15.40
E
10.11
10.51
E1
7.34
7.60
E
e
PIN#1 IDENTIFICATION
MAX
1.27 BSC
e
b
NOM
h
0.25
0.75
L
0.40
1.27
θ
0º
8º
θ1
5º
15º
TOP VIEW
h
D
A2
A
A1
SIDE VIEW
h
q1
q
q1
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-013.
http://onsemi.com
14
c
CAT5419
PACKAGE DIMENSIONS
TSSOP24, 4.4x7.8
CASE 948AR
ISSUE A
b
SYMBOL
MIN
NOM
A
E1 E
MAX
1.20
A1
0.05
0.15
A2
0.80
1.05
b
0.19
0.30
c
0.09
0.20
D
7.70
7.80
7.90
E
6.25
6.40
6.55
E1
4.30
4.40
4.50
e
L
0.65 BSC
0.50
L1
θ
0.60
0.70
1.00 REF
0º
8º
e
TOP VIEW
D
c
A2
A θ1
L
A1
SIDE VIEW
END VIEW
L1
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT5419/D
Similar pages