CUI CDMG13008L-02

Date: 10/18/2006
Part No: CDMG13008L-02
Unit: mm
Description: micro dynamic speaker
Page No: 1 of 6
Specifications
Dimensions
Impedance
Resonant frequency
Sound pressure level
ø13.0 x 2.0 mm
8 Ohm ± 15%
at
1.5 KHz 1 V
1050 Hz ± 20%
at
1V
86 dB/w ± 3 dB
0.2 w 10 cm at 1.5K, 2.0K, 2.5K, 3.0K Hz
75 dB/w ± 3 dB
1 w 1m at 1.5K, 2.0K, 2.5K, 3.0K Hz
Fo Hz ~ 20 KHz max.
10% max.
at 1.5 KHz 0.2W
Nominal
0.2 W Handling capacity
0.4 W
must be normal at program source 0.2 W
must be normal at sine wave 1.26 V
ø7.0 x 0.7 (Nd-Fe-B)
-20 ~ +55°C
0.7 g
Metal
yes
Response
Distortion
Input power
Operation
Buzz, rattle, etc.
Magnet
Operating temp.
Weight
Material
RoHS
Mechanical Drawing
Tolerance: ±0.3
Week
01
02
.
.
Year
05---2005
06---2006
.
.
2.0
1.0
13.0
9.0
SOLDERING
POINT
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
BLACK
POLYESTER
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CDMG13008L-02
Date: 10/18/2006
Unit: mm
Description: micro dynamic speaker
Page No: 2 of 6
Frequency Response Curve
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CDMG13008L-02
Date: 10/18/2006
Unit: mm
Description: micro dynamic speaker
Page No: 3 of 6
Measurement Circuit
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Date: 10/18/2006
Part No: CDMG13008L-02
Unit: mm
Description: micro dynamic speaker
Page No: 4 of 6
Mechanical Characteristics
Item
PCB Wire Pull Strength
Vibration
Drop Test
Evaluation Standard
Test Condition
The pull force should be applied to double lead
No damage or cutting off.
wire:
Horizontal 3.0N (0.306kg) for 30 seconds
The speaker should be measured after applying
No obstacle will be harmful to
a vibration amplitude of 1.5 mm with 10 to
normal operation; damage,
55 Hz band of vibration frequency to each of
cracks, rust, and distortions.
the 3 perpendicular directions for 2 hours.
Should not be audible at 1.26 V
The part will be dropped, contained inside a
sine wave between Fo ~ 20 KHz.
normal box, from a height of 75 cm onto a 40
mm thick wooden board 10 times.
Environment Test
Item
High temp. test
Low temp. test
Humidity test
Temp. cycle test
Phone: 800.275.4899
Test Condition
After being placed in a chamber at 55°C for
96 hours.
After being placed in a chamber at -20°C for
96 hours.
After being placed in a chamber at +40°C and
90% relative humidity for 240 hours.
The part shall be subjected to 5 cycles. One
cycle will consist of:
Fax: 503.612.2381
www.cui.com
Evaluation Standard
The speaker will be measured
after being placed at +25°C for 6
hours. No obstacle will be harm
ful to normal operation; damage,
cracks, rust, and distortions.
Should not be audible at 1.26 V
sine wave between Fo ~ 20 KHz.
The SPL should be within ±3dB
compared to the initial
measurements.
20050 SW 112th Ave.
Tualatin, OR 97062
Date: 10/18/2006
Part No: CDMG13008L-02
Unit: mm
Description: micro dynamic speaker
Page No: 5 of 6
Reliability Test
Item
Load Test
Test Condition
0.2 W white noise, applied for 96 hours, at
room temperature.
Evaluation Standard
The speaker will be measured
after being placed at +25°C for 6
hours. No obstacle will be harm
ful to normal operation; damage,
cracks, rust, and distortions.
Should not be audible at 1.26 V
sine wave between Fo ~ 20 KHz.
The SPL should be within ±3dB
compared to the initial
measurements.
Test Conditions
Standard Test Condition
Judgement Test Condition
a) Tempurature: +5 ~ +35°C
a) Tempurature: +25 ±2°C
b) Humidity: 45 - 85%
b) Humidity: 60 - 70%
c) Pressure: 860-1060 mbar
c) Pressure: 860-1060 mbar
Recommended Temperature Profile for Hand Soldering
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Part No: CDMG13008L-02
Date: 10/18/2006
Unit: mm
Description: micro dynamic speaker
Page No: 6 of 6
Packaging
Phone: 800.275.4899
Fax: 503.612.2381
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062