TI1 CLVC1G374QDCKRQ1 sinfle d-type flip-flop with 3-state output Datasheet

 SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
D
D
D
D
D
D
D
D Latch-Up Performance Exceeds 100 mA
Qualified for Automotive Applications
Supports 5-V VCC Operation
Inputs Accept Voltages to 5.5 V
Max tpd of 4 ns at 3.3 V
Low Power Consumption, 10-µA Max ICC
±24-mA Output Drive at 3.3 V
Per JESD 78, Class II
D ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
Ioff Supports Partial-Power-Down Mode
Operation
DBV OR DCK PACKAGE
(TOP VIEW)
description/ordering information
CLK
GND
D
This single D-type flip-flop is designed for 1.65-V to
5.5-V VCC operation.
1
6
2
5
3
4
OE
VCC
Q
The SN74LVC1G374 features a 3-state output
designed specifically for driving highly capacitive or
relatively low-impedance loads. This device is
particularly suitable for implementing buffer registers,
input/output (I/O) ports, bidirectional bus drivers, and
working registers.
On the positive transition of the clock (CLK) input, the Q output is set to the logic level set up at the data (D)
input.
A buffered output-enable (OE) input can be used to place the output in either a normal logic state (high or low
logic levels) or the high-impedance state. In the high-impedance state, the output neither loads nor drives the
bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines
without interface or pullup components.
OE does not affect the internal operations of the flip-flop. Old data can be retained or new data can be entered
while the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
ORDERING INFORMATION {
−40°C to 125°C
ORDERABLE
PART NUMBER
PACKAGE}
TA
TOP-SIDE
MARKING§
SOT (SOT-23) − DBV
Reel of 3000
SN74LVC1G374QDBVRQ1
CA40
SOT (SC-70) − DCK
Reel of 3000
SN74LVC1G374QDCKRQ1
D40
† For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see
the TI web site at http://www.ti.com.
}Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
§ DBV/DCK: The actual top-side marking has one additional character that designates the wafer fab/assembly site.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2008, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
FUNCTION TABLE
INPUTS
D
OUTPUT
Q
OE
CLK
L
↑
L
L
L
↑
H
H
L
H or L
X
Q
H
X
X
Z
logic diagram (positive logic)
OE
CLK
6
1
C1
D
3
D
4
Q
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V
Voltage range applied to any output in the high-impedance or power-off state, VO
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V
Voltage range applied to any output in the high or low state, VO
(see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 3): DBV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165°C/W
DCK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
2. The value of VCC is provided in the recommended operating conditions table.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
recommended operating conditions (see Note 4)
Operating
VCC
VIH
Supply voltage
High-level input voltage
VIL
Low-level input voltage
VI
VO
Input voltage
Data retention only
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3 V to 3.6 V
VCC = 4.5 V to 5.5 V
MIN
MAX
1.65
5.5
0.65 × VCC
1.7
V
2
0.7 × VCC
0.35 × VCC
0.7
VCC = 3 V to 3.6 V
VCC = 4.5 V to 5.5 V
VCC = 1.65 V
VCC = 2.3 V
V
1.5
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
Output voltage
UNIT
0.8
V
0.3 × VCC
0
5.5
V
0
VCC
−4
V
−8
−16
IOH
High-level output current
VCC = 3 V
VCC = 4.5 V
VCC = 5 V, TA = −40°C to 85°C
VCC = 1.65 V
VCC = 2.3 V
−24
mA
−32
−40
4
8
16
IOL
∆t/∆v
Low-level output current
Input transition rise or fall rate
VCC = 3 V
24
VCC = 4.5 V
VCC = 5 V, TA = −40°C to 85°C
32
VCC = 1.8 V ± 0.15 V, 2.5 V ± 0.2 V
VCC = 3.3 V ± 0.3 V
20
VCC = 5 V ± 0.5 V
mA
40
10
ns/V
5
TA
Operating free-air temperature
−40
125
°C
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = −100 mA
IOH = −4 mA
VOH
1.65 V to 5.5 V
1.65 V
IOH = −8 mA
IOH = −16 mA
2.3 V
3V
IOH = −24 mA
1.9
2.4
2.4
2.3
2.3
3.8
3.8
IOH = −40 mA
5V
4.4
V
1.65 V to 5.5 V
0.1
0.1
1.65 V
0.45
0.45
2.3 V
0.3
0.3
0.4
0.5
0.55
0.65
0.65
3V
IOL = 24 mA
UNIT
VCC − 0.1
1.2
1.9
4.5 V
IOL = 8 mA
IOL = 16 mA
TA = −405C TO 1255C
MIN
MAX
TYP†
VCC − 0.1
1.2
IOH = −32 mA
IOL = 100 mA
IOL = 4 mA
VOL
TA = −405C TO 855C
MIN
MAX
TYP†
VCC
IOL = 32 mA
4.5 V
0.55
IOL = 40 mA
5V
0.513
V
II
IOZ
VI = 5.5 V or GND
VO = 0 to 5.5 V
0 to 5.5 V
±1
±2
mA
1.65 V to 5.5 V
±5
±12
mA
Ioff
ICC
VI or VO = 5.5 V
VI = 5.5 V or GND, IO = 0
±10
±25
mA
1.65 V to 5.5 V
10
10
mA
∆ICC
One input at VCC − 0.6 V,
Other inputs at VCC or GND
3 V to 5.5 V
500
500
mA
Ci
VI = VCC or GND
0
Co
VO = VCC or GND
† All typical values are at VCC = 3.3 V, TA = 25°C.
3.3 V
3
3
pF
3.3 V
6
6
pF
timing requirements over recommended operating free-air temperature range (unless otherwise
noted) (see Figure 1)
VCC = 1.8 V
± 0.15 V
MIN
4
MAX
VCC = 2.5 V
± 0.2 V
MIN
fclock
tw
Clock frequency
Pulse duration, CLK high or low
3.3
100
3
tsu
th
Setup time, data before CLK↑
3.5
Hold time, data after CLK↑
3.4
POST OFFICE BOX 655303
MAX
VCC = 3.3 V
± 0.3 V
MIN
125
MAX
VCC = 5 V
± 0.5 V
MIN
150
UNIT
MAX
175
MHz
2.8
2.5
ns
2.5
2
1.5
ns
1.6
1.5
1.5
ns
• DALLAS, TEXAS 75265
SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
switching characteristics over free-air temperature range of −405C to 855C, CL = 30 pF or 50 pF
(unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
VCC = 1.8 V
± 0.15 V
MIN
VCC = 2.5 V
± 0.2 V
MAX
100
MIN
MAX
125
VCC = 3.3 V
± 0.3 V
MIN
MAX
150
VCC = 5 V
± 0.5 V
MIN
UNIT
MAX
175
MHz
tpd
CLK
Q
2.7
18.3
1.8
8.2
1.6
6
1
4
ns
ten
OE
Q
2
13
1.5
6.3
0.9
5
0.7
3.5
ns
tdis
OE
Q
2
14
1.1
5.3
1.4
4.5
0.8
3.1
ns
switching characteristics over free-air temperature range of −405C to 1255C, CL = 30 pF or 50 pF
(unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
fmax
VCC = 1.8 V
± 0.15 V
MIN
VCC = 2.5 V
± 0.2 V
MAX
100
MIN
MAX
125
VCC = 3.3 V
± 0.3 V
MIN
MAX
150
VCC = 5 V
± 0.5 V
MIN
UNIT
MAX
175
MHz
tpd
CLK
Q
2.7
18.3
1.8
10.2
1.6
7
1
5
ns
ten
OE
Q
2
14
1.5
8.3
0.9
6.5
0.7
5.5
ns
tdis
OE
Q
2
16
1.1
7.3
1.4
6
0.8
5.1
ns
operating characteristics, TA = 25°C
TEST
CONDITIONS
PARAMETER
Cpd
Power dissipation
capacitance
Outputs enabled
Outputs disabled
f = 10 MHz
POST OFFICE BOX 655303
VCC = 1.8 V
TYP
VCC = 2.5 V
TYP
VCC = 3.3 V
TYP
VCC = 5 V
TYP
24
24
25
27
8
8
9
11
• DALLAS, TEXAS 75265
UNIT
pF
5
SCES607A − SEPTEMBER 2004 − REVISED APRIL 2008
PARAMETER MEASUREMENT INFORMATION
RL
From Output
Under Test
CL
(see Note A)
VLOAD
Open
S1
GND
RL
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
VLOAD
GND
LOAD CIRCUIT
INPUTS
VCC
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5 V ± 0.5 V
VI
tr/tf
VCC
VCC
3V
VCC
≤2 ns
≤2 ns
≤2.5 ns
≤2.5 ns
VM
VLOAD
CL
RL
V∆
VCC/2
VCC/2
1.5 V
VCC/2
2 × VCC
2 × VCC
6V
2 × VCC
30 pF
30 pF
50 pF
50 pF
1 kΩ
500 Ω
500 Ω
500 Ω
0.15 V
0.15 V
0.3 V
0.3 V
VI
Timing Input
VM
0V
tw
tsu
VI
Input
VM
VM
th
VI
Data Input
VM
VM
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VI
VM
Input
VM
0V
tPLH
tPHL
VOH
VM
Output
VM
VOL
tPHL
Output
Waveform 1
S1 at VLOAD
(see Note B)
tPLH
VM
VM
VM
0V
tPZL
tPLZ
VLOAD/2
VM
tPZH
VOH
Output
VI
Output
Control
VM
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
Output
Waveform 2
S1 at GND
(see Note B)
VOL + V∆
VOL
tPHZ
VM
VOH − V∆
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
7-Dec-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
CLVC1G374QDBVRQ1
ACTIVE
SOT-23
DBV
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CLVC1G374QDCKRQ1
ACTIVE
SC70
DCK
6
3000 Green (RoHS &
no Sb/Br)
NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN74LVC1G374-Q1 :
• Catalog: SN74LVC1G374
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages