AD CN-0121 Synchronizing multiple ad9910 1 gsps direct digital synthesizer Datasheet

Circuit Note
CN-0121
Devices Connected/Referenced
Circuit Designs Using Analog Devices Products
Apply these product pairings quickly and with confidence.
For more information and/or support call 1-800-AnalogD
(1-800-262-5643) or visit www.analog.com/circuit.
AD9910
1 GSPS Direct Digital Synthesizer (DDS)
AD9520
Clock Generator and Distribution IC
ADCLK846
High Speed LVDS Clock Fanout Buffer
Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers
CIRCUIT FUNCTION AND BENEFITS
The circuit in Figure 1 demonstrates how to synchronize four
AD9910 1 GSPS, DDS chips using the AD9520 clock generator
and the ADCLK846 clock fanout buffer. The result is precise
phase alignment between the clock and output signals of four
AD9910 devices.
Synchronization of multiple DDS devices allows precise digital
tuning control of the phase and amplitude across multiple
frequency carriers. This type of control is useful in radar
applications and quadrature (I/Q) upconversion for side-band
suppression.
LVDS
LEVELS
ADCLK846
Q0
Q0
Q1
LVDS
LEVELS
CLK1
Q1
Q2
CLK1
Q2
Q3
Q3
+ SYNC_IN
– SYNC_IN
SYNC_CLK
AD9910
AD9520
Q0
Q1
Q2
Q3
Q4
PECL
LEVELS
AOUT
(MASTER)
REF CLK
IO_UPDATE
REF CLK
+ SYNC_OUT
– SYNC_OUT
SYNC_CLK
IO_UPDATE
AD9910
CMOS
LEVEL
AOUT
(SLAVE)
CMOS
LEVELS
DATA
GENERATOR
+ SYNC_IN
– SYNC_IN
REF CLK
CH2
SYNC_CLK
CH3
AOUT
CH4
IO_UPDATE
CLOCK
SCOPE
CH1
DG2020A
AD9910
(SLAVE)
+ SYNC_IN
– SYNC_IN
REF CLK
SYNC_CLK
IO_UPDATE
AOUT
AD9910
+ SYNC_IN
– SYNC_IN
08514-001
(SLAVE)
Figure 1. Setup for Synchronization of Multiple AD9910’s (Simplified Schematic: Decoupling, Power, and All Connections Not Shown)
Rev. A
“Circuits from the Lab” from Analog Devices have been designed and built by Analog Devices
engineers. Standard engineering practices have been employed in the design and construction of
each circuit, and their function and performance have been tested and verified in a lab environment
at room temperature. However, you are solely responsible for testing the circuit and determining its
suitability and applicability for your use and application. Accordingly, in no event shall Analog
Devices be liable for direct, indirect, special, incidental, consequential or punitive damages due to
any cause whatsoever connected to the use of any“Circuit from the Lab”. (Continued on last page)
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
CN-0121
Circuit Note
CIRCUIT DESCRIPTION
The circuit in Figure 1 was constructed by connecting the
respective evaluation boards for the individual products.
Connections were made with matched cable lengths. The first
of three basic requirements to synchronize multiple AD9910’s is
to provide a co-incident reference clock (REF CLK).
The setup uses the AD9520 as the REF CLK source for each
AD9910 DDS. The AD9520 runs off an external crystal and the
internal PLL. The AD9520 distributes phase aligned 1 GHz REF
CLKs (PECL outputs) to all four AD9910 evaluation boards. It
also provides a CMOS output clock to the Tektronix DG2020A
data pattern generator for the IO_UPDATE.
The next step for synchronization is to align the rising edge of
SYNC_CLK for all four AD9910’s. The SYNC_CLK provides
the reference for a co-incident IO_UPDATE. SYNC_CLK
alignment is accomplished using the internal synchronization
capability of the AD9910. The ADCLK846 distributes phase
aligned SYNC_INs to all four AD9910s. See the AD9910 data
sheet for more details on synchronization capability.
The last requirement to synchronize multiple DDS devices is a
co-incident IO_UPDATE. The IO_UPDATE must meet setup
and hold times to SYNC_CLK. The IO_UPDATE shown in
Figure 1 is sent synchronously to the SYNC_CLK. The last
requirement now enables the DDS outputs to be controlled.
Figures 4 and 5 show the DDS outputs in phase alignment.
Having the devices synchronized to one another now enables
predictable phase and/or amplitude adjustment between DDSs.
Note, in Figure 5 the system clock was reduced to 100 MHz
operation, and the outputs were unfiltered to display each DDS
raw output. Figure 5 also shows the value of synchronization
with each device outputting the same signal.
To phase align the SYNC_CLK rising edges, one AD9910 is
programmed as the master device and the others as slave
devices. The SYNC_OUT of the master device is an LVDS
signal buffered and distributed by the ADCLK846 to all
AD9910 evaluation boards. The SYNC_IN signal (LVDS) must
meet internal setup and hold time requirements of each
device’s system clock. To help support this timing requirement,
the AD9910 features the ability to delay the SYNC_OUT of the
master. For further flexibility, the internal SYNC_IN path of
each device can be independently delayed.
C3 FREQUENCY
249.54MHz
LOW SIGNAL
AMPLITUDE
1
2
3
4
08514-003
Figure 2 shows all four SYNC_CLKs with the AD9910 internal
synchronization circuit disabled. Note that the SYNC_CLKs are
not inherently aligned even when the REF CLKs are phase
aligned.
CH1 1.00VΩ CH2 1.00VΩ
CH3 1.00VΩ CH4 1.00VΩ
M2.00ns
CH1
480mV
Figure 3. SYNC_CLK Are Aligned.
C3 FREQUENCY
125.321MHz
C3 FREQUENCY
250.76MHz
LOW SIGNAL
AMPLITUDE
1
In the setup of Figure 1, connections between boards were
made using matched cables, making it possible to use the
internal default delay values to phase align the SYNC_CLKs.
Figure 3 shows SYNC_CLK phase alignment via the using the
synchronization procedure described.
1
2
2
3
3
08514-002
4
CH1 1.00VΩ CH2 1.00VΩ
CH3 1.00VΩ CH4 1.00VΩ
M2.00ns
CH2
480mV
Figure 2. SYNC_CLKs Are Not Aligned.
08514-004
4
CH1 200mVΩ
CH3 200mVΩ
B
W
B
W
CH2 200mVΩ BW M5.00ns
CH4 200mVΩ BW
CH2
–80V
Figure 4. Filtered DDS Outputs Phase Aligned Using the Setup in Figure 1.
Rev. A | Page 2 of 3
Circuit Note
CN-0121
LEARN MORE
1
AN-823 Application Note, Direct Digital Synthesizers in
Clocking Applications. Analog Devices.
2
AN-837 Application Note, DDS-Based Clock Jitter Performance
vs. DAC Reconstruction Filter Performance. Analog Devices.
Kester, Walt. 2005. The Data Conversion Handbook. Analog
Devices. Chapters 6 and 7.
3
Kester, Walt. 2006. High Speed System Applications. Analog
Devices. Chapter 2, “Optimizing Data Converter Interfaces.”
4
08514-005
Kester, Walt. 2006. High Speed System Applications. Analog
Devices. Chapter 3, “DACs, DDSs, PLLs, and Clock
Distribution.”
CH1 200mVΩ
CH3 200mVΩ
CH2 200mVΩ M20.0ns
CH4 200mVΩ
CH2
–80V
Figure 5. DDS Unfiltered Outputs Phase Aligned Using the Setup in Figure 1.
COMMON VARIATIONS
Analog Devices offers a variety of direct digital synthesizers,
clock distribution chips, and clock buffers to build a DDS-based
clock generator. Refer to www.analog.com/dds and
www.analog.com/clock for more information.
MT-031 Tutorial, Grounding Data Converters and Solving the
Mystery of AGND and DGND. Analog Devices.
MT-085 Tutorial, Fundamentals of Direct Digital Synthesis
(DDS), Analog Devices.
MT-086 Tutorial, Fundamentals of Phase Locked Loops (PLL),
Analog Devices.
MT-101 Tutorial, Decoupling Techniques. Analog Devices.
Data Sheets and Evaluation Boards
AD9910 Data Sheet.
AD9910 Evaluation Board.
AD9520 Data Sheet.
AD9520 Evaluation Board.
ADCLK846 Data Sheet.
ADCLK846 Evaluation Board.
REVISION HISTORY
12/09—Rev. 0 to Rev. A
Changes to Figure 1 .......................................................................... 1
10/09—Revision 0: Initial Version
(Continued from first page) "Circuits from the Lab" are intended only for use with Analog Devices products and are the intellectual property of Analog Devices or its licensors. While you may
use the "Circuits from the Lab" in the design of your product, no other license is granted by implication or otherwise under any patents or other intellectual property by application or use of
the "Circuits from the Lab". Information furnished by Analog Devices is believed to be accurate and reliable. However, "Circuits from the Lab" are supplied "as is" and without warranties of any
kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability, noninfringement or fitness for a particular purpose and no responsibility is assumed
by Analog Devices for their use, nor for any infringements of patents or other rights of third parties that may result from their use. Analog Devices reserves the right to change any "Circuits
from the Lab" at any time without notice, but is under no obligation to do so. Trademarks and registered trademarks are the property of their respective owners.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
CN08514-0-12/09(A)
Rev. A | Page 3 of 3
Similar pages