NSC COP87L20CJM-1N 8-bit microcontroller with multi-input wake up and brown out detector Datasheet

COP820CJ/COP822CJ/COP823CJ 8-Bit Microcontroller
with Multi-Input Wake Up and Brown Out Detector
Y
General Description
COP8TM
The COP820CJ is a member of the
8-bit Microcontroller family. It is a fully static Microcontroller, fabricated
using double-metal silicon gate microCMOS technology.
This low cost Microcontroller is a complete microcomputer
containing all system timing, interrupt logic, ROM, RAM, and
I/O necessary to implement dedicated control functions in a
variety of applications. Features include an 8-bit memory
mapped architecture, MICROWIRETM serial I/O, a 16-bit
timer/counter with capture register, a multi-sourced interrupt, Comparator, WATCHDOGTM Timer, Modulator/Timer,
Brown out protection and Multi-Input Wakeup. Each I/O pin
has software selectable options to adapt the device to the
specific application. The device operates over a voltage
range of 2.5V to 6.0V. High throughput is achieved with an
efficient, regular instruction set operating at a 1 ms per instruction rate.
Y
Y
Y
Y
Y
Y
Y
Y
Y
CPU/Instruction Set Feature
Y
Y
Y
Key Features
Y
Y
Y
Multi-Input Wake Up (on the 8-bit Port L)
Brown out detector
Analog comparator
Modulator/timer (High speed PWM for IR transmission)
16-bit multi-function timer supporting
Ð PWM mode
Ð External event counter mode
Ð Input capture mode
1024 bytes of ROM
64 bytes of RAM
Y
Y
1 ms instruction cycle time
Three multi-source vectored interrupts servicing
Ð External interrupt with selectable edge
Ð Timer interrupt
Ð Software interrupt
Versatile and easy to use instruction set
8-bit Stack Pointer (SP)Ðstack in RAM
Two 8-bit register indirect data memory pointers (B, X)
Fully Static CMOS
Y
Y
Y
Low current drain (typically k 1 mA)
Single supply operation: 2.5V to 6.0V
Temperature range: b40§ C to a 85§ C
Development Support
Y
Y
I/O Features
Software selectable I/O options (TRI-STATEÉ output,
push-pull output, weak pull-up input, high impedance
input)
High current outputs (8 pins)
Schmitt trigger inputs on Port G
MICROWIRE/PLUSTM serial I/O
Packages
Ð 16 SO with 12 I/O pins
Ð 20 DIP/SO with 16 I/O pins
Ð 28 DIP/SO with 24 I/O pins
Emulation and OTP devices
Real time emulation and full program debug offered by
MetaLink Development System
Memory mapped I/O
Block Diagram
TL/DD/11208 – 1
FIGURE 1. Block Diagram
TRI-STATEÉ is a registered trademark of National Semiconductor Corporation.
COP8TM Microcontrollers, MICROWIRETM , MICROWIRE/PLUSTM and WATCHDOGTM are trademarks of National Semiconductor Corporation.
iceMASTERTM is a trademark of MetaLink Corporation.
C1996 National Semiconductor Corporation
TL/DD11208
RRD-B30M106/Printed in U. S. A.
http://www.national.com
COP820CJ/COP822CJ/COP823CJ 8-Bit Microcontroller
with Multi-Input Wake Up and Brown Out Detector
September 1996
COP820CJ/COP822CJ/COP823CJ
Absolute Maximum Ratings
Total Current out of GND pin (sink)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Supply Voltage (VCC)
7.0V
Voltage at any Pin
Total Current into VCC pin (Source)
Storage Temperature Range
80 mA
b 65§ C to a 150§ C
Note: Absolute maximum ratings indicate limits beyond
which damage to the device may occur.
DC and AC electrical specifications are not ensured when
operating the device at absolute maximum ratings.
b 0.3V to VCC a 0.3V
80 mA
DC Electrical Characteristics b40§ C s TA s a 85§ C unless otherwise specified
Parameter
Operating Voltage
Power Supply Ripple 1 (Note 1)
Supply Current (Note 2)
CKI e 10 MHz
CKI e 4 MHz
CKI e 4 MHz
CKI e 1 MHz
HALT Current with Brown Out
Disbled (Note 3)
HALT Current with Brown Out
Enabled
Conditions
Min
Brown Out Disabled
Peak to Peak
VCC
VCC
VCC
VCC
e
e
e
e
VCC e 6V, CKI e 0 MHz
VCC e 6V, CKI e 0 MHz
1.8
INPUT LEVELS (VIH, VIL)
Reset, CKI:
Logic High
Logic Low
All Other Inputs
Logic High
Logic Low
VCC e 6.0V
VCC e 6.0V, VIN e 0V
Sink (Push-pull Mode)
mA
mA
mA
mA
k1
10
mA
k 50
110
mA
3.1
4.2
V
0.2 VCC
V
V
0.2 VCC
V
V
b2
a2
mA
b 250
mA
0.35 VCC
V
VCC
VCC
VCC
VCC
VCC
e
e
e
e
e
4.5V, VOH e 3.8V
2.5V, VOH e 1.8V
4.5V, VOL e 1.0V
2.5V, VOH e 0.4V
4.5V, VOL e 2.5V
b 0.4
b 0.2
VCC
VCC
VCC
VCC
VCC
VCC
e
e
e
e
e
e
4.5V, VOH e 3.2V
2.5V, VOH e 1.8V
4.5V, VOH e 3.8V
2.5V, VOH e 1.8V
4.5V, VOL e 0.4V
2.5V, VOL e 0.4V
b 10
b 2.5
b 0.4
b 0.2
TRI-STATE Leakage
Allowable Sink/Source
Current Per Pin
D Outputs
L4 – L7 (Sink)
All Others
http://www.national.com
6.0
3.5
2.0
1.5
b 40
L- and G-Port Hysteresis (Note 5)
Source (Push-pull Mode)
V
V
0.7 VCC
Input Pullup Current
L4 – L7 Output Sink
All Others
Source (Weak Pull-up Mode)
Units
6.0
0.1 VCC
0.8 VCC
Hi-Z Input Leakage
Sink
Max
6V, tc e 1 ms
6V, tc e 2.5 ms
4.0V, tc e 2.5 ms
4.0V, tc e 10 ms
Brown Out Trip Level
(Brown Out Enabled)
Output Current Levels
D Outputs:
Source
Typ
2.5
2
mA
mA
mA
mA
mA
10
2
15
1.6
0.7
b 2.0
b 110
b 33
a 2.0
mA
mA
mA
mA
mA
mA
mA
15
20
3
mA
mA
mA
DC Electrical Characteristics b40§ C s TA s a 85§ C unless otherwise specified (Continued)
Parameter
Conditions
Maximum Input Current
without Latchup (Note 4)
Room Temperature
RAM Retention Voltage, Vr
500 ns Rise and
Fall Time (Min)
Min
Typ
Max
Units
g 100
mA
2.0
V
Input Capacitance
Load Capacitance on D2
7
pF
1000
pF
Note 1: Rate of voltage change must be less than 10 V/mS.
Note 2: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 3: The HALT mode will stop CKI from oscillating in the RC and crystal configurations. HALT test conditions: L, and G0..G5 ports configured as outputs and set
high. The D port set to zero. All inputs tied to VCC. The comparator and the Brown Out circuits are disabled.
Note 4: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than VCC and the pins will have sink current to
VCC when biased at voltages greater than VCC (the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCC is 750X
(typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V.
AC Electrical Characteristics b40§ C s TA s a 85§ C unless otherwise specified
Parameter
Instruction Cycle Time (tc)
Crystal/Resonator
Conditions
Min
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
1
2.5
3
7.5
VCC Rise Time when Using Brown Out
Frequency at Brown Out Reset
CKI Frequency For Modular Output
VCC e 0V to 6V
50
CKI Clock Duty Cycle (Note 5)
Rise Time (Note 5)
Fall Time (Note 5)
fr e Max
fr e 10 MHz ext. Clock
fr e 10 MHz ext. Clock
40
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
200
500
60
150
R/C Oscillator
Inputs
tSetup
tHold
Output Propagation Delay
tPD1, tPD0
SO, SK
All Others
Typ
Max
Units
DC
DC
DC
DC
ms
ms
ms
ms
4
4
ms
MHz
MHz
60
12
8
%
ns
ns
ns
ns
ns
ns
RL e 2.2k, CL e 100 pF
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
4.5V s VCC s 6.0V
2.5V s VCC s 4.5V
Input Pulse Width
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer Input Low Time
0.7
1.75
1
5
ms
ms
ms
ms
1
1
1
1
tc
tc
tc
tc
MICROWIRE Setup Time (tmWS)
MICROWIRE Hold Time (tmWH)
MICROWIRE Output
Propagation Delay (tmPD)
20
56
ns
ns
Reset Pulse Width
1.0
220
ns
ms
Note 5: Parameter characterized but not production tested.
3
http://www.national.com
AC Electrical Characteristics (Continued)
TL/DD/11208 – 2
FIGURE 2. MICROWIRE/PLUS Timing
Comparator DC and AC Characteristics 4V s VCC s 6V, b40§ C s TA s a 85§ C (Note 1)
Parameters
Conditions
Input Offset Voltage
Min
0.4V k VIN k VCC b 1.5V
Input Common Mode Voltage Range
Type
Max
Units
g 10
g 25
mV
0.4
Voltage Gain
VCC b 1.5
300k
DC Supply Current (when enabled)
VCC e 6.0V
Response Time
TBD mV Step,
TBD mV Overdrive, 100 pF Load
V
V/V
250
mA
1
ms
Note 1: For comparator output current characteristics see L-Port specs.
Connection Diagrams
TL/DD/11208 – 5
TL/DD/11208 – 4
Top View
TL/DD/11208–3
Top View
Order Number COPCJ822-XXX/N or
COPCJ822-XXX/WM
Order Number COPCJ820-XXX/N or
COPCJ820-XXX/WM
FIGURE 3. Connection Diagrams
http://www.national.com
4
Top View
Order Number COPCJ823-XXX/WM
Typical Performance Characteristics
DynamicÐIDD vs VCC
(Crystal Clock Option)
HaltÐIDD vs VCC
(Brown Out Disabled)
HaltÐIDD vs VCC
(Brown Out Enabled)
Ports L/G Weak
Pull-Up Source Current
Ports L/G Push-Pull
Source Current
Ports L/G Push-Pull
Sink Current
Ports L4–L7
Sink Current
Port D Source Current
Port D Sink Current
Brown Out Voltage
vs Temperature
TL/DD/11208 – 28
5
http://www.national.com
I/O bit can be individually configured under software control
as shown below:
COP820CJ Pin Assignment
Port
Pin
Typ
ALT
Funct.
16
Pin
L0
I/O
MIWU/CMPOUT
5
L1
I/O
MIWU/CMPINb
6
L2
I/O
MIWU/CMPIN a
7
9
13
L3
I/O
MIWU
8
10
14
L4
I/O
MIWU
9
11
15
L5
I/O
MIWU
10
12
16
L6
I/O
MIWU
11
13
17
L7
I/O
MIWU/MODOUT
12
14
18
G0
I/O
INTR
17
25
G1
I/O
18
26
G2
I/O
19
27
G3
I/O
TIO
20
28
G4
I/O
SO
1
1
G5
I/O
SK
16
2
2
G6
I
SI
1
3
3
G7
I
CKO
2
4
I0
I
7
I1
I
8
I2
I
9
I3
I
10
D0
O
19
D1
O
20
D2
O
21
D3
O
22
15
20
Pin
28
Pin
Port L
Config.
Port L
Data
Port L
Setup
7
11
8
12
0
0
1
1
0
1
0
1
Hi-Z Input (TRI-STATE)
Input with Weak Pull-up
Push-pull Zero Output
Push-pull One Output
Three data memory address locations are allocated for this
port, one each for data register [00D0], configuration register [00D1] and the input pins [00D2].
Port L has the following alternate features:
L0 MIWU or CMPOUT
L1 MIWU or CMPINb
L2 MIWU or CMPIN a
L3 MIWU
L4 MIWU (high sink current capability)
L5 MIWU (high sink current capability)
L6 MIWU (high sink current capability)
L7 MIWU or MODOUT (high sink current capability)
The selection of alternate Port L functions is done through
registers WKEN [00C9] to enable MIWU and CNTRL2
[00CC] to enable comparator and modulator.
All eight L-pins have Schmitt Triggers on their inputs.
PORT G is an 8-bit port with 6 I/O pins (G0 – G5) and 2 input
pins (G6, G7).
All eight G-pins have Schmitt Triggers on the inputs.
There are two registers associated with the G port: a data
register and a configuration register. Therefore each G port
bit can be individually configured under software control as
shown below:
4
VCC
4
6
6
GND
13
15
23
CKI
3
5
5
RESET
14
16
24
Port G
Data
Port G
Setup
0
0
1
1
0
1
0
1
Hi-Z Input (TRI-STATE)
Input with Weak Pull-up
Push-pull Zero Output
Push-pull One Output
Three data memory address locations are allocated for this
port, one for data register [00D3], one for configuration register [00D5] and one for the input pins [00D6]. Since G6
and G7 are Hi-Z input only pins, any attempt by the user to
configure them as outputs by writing a one to the configuration register will be disregarded. Reading the G6 and G7
configuration bits will return zeros. Note that the device will
be placed in the Halt mode by writing a ‘‘1’’ to the G7 data
bit.
Six pins of Port G have alternate features:
G0 INTR (an external interrupt)
G3 TIO (timer/counter input/output)
G4 SO (MICROWIRE serial data output)
G5 SK (MICROWIRE clock I/O)
G6 SI (MICROWIRE serial data input)
G7 CKO crystal oscillator output (selected by mask option)
or HALT restart input/general purpose input (if clock
option is R/C or external clock)
Pin Description
VCC and GND are the power supply pins.
CKI is the clock input. This can come from an external
source, a R/C generated oscillator or a crystal (in conjunction with CKO). See Oscillator description.
RESET is the master reset input. See Reset description.
PORT I is a 4-bit Hi-Z input port.
PORT L is an 8-bit I/O port.
There are two registers associated with the L port: a data
register and a configuration register. Therefore, each L
http://www.national.com
Port G
Config.
6
Any bit of data memory can be directly set, reset or tested.
All I/O and registers (except A and PC) are memory
mapped; therefore, I/O bits and register bits can be directly
and individually set, reset and tested, except the write once
only bit (WDREN, WATCHDOG Reset Enable), and the unused and read only bits in CNTRL2 and WDREG registers.
Pin Description (Continued)
Pins G1 and G2 currently do not have any alternate functions.
The selection of alternate Port G functions are done through
registers PSW [00EF] to enable external interrupt and
CNTRL1 [00EE] to select TIO and MICROWIRE operations.
PORT D is a four bit output port that is preset when RESET
goes low. One data memory address location is allocated
for the data register [00DC].
Note: RAM contents are undefined upon power-up.
Reset
EXTERNAL RESET
The RESET input pin when pulled low initializes the microcontroller. The user must insure that the RESET pin is held
low until VCC is within the specified voltage range and the
clock is stabilized. An R/C circuit with a delay 5x greater
than the power supply rise time is recommended (Figure 4) .
The device immediately goes into reset state when the
RESET input goes low. When the RESET pin goes high the
device comes out of reset state synchronously. The device
will be running within two instruction cycles of the RESET
pin going high. The following actions occur upon reset:
Note: Care must be exercised with the D2 pin operation. At RESET, the
external loads on this pin must ensure that the output voltages stay above
0.8 VCC to prevent the chip from entering special modes. Also keep the
external loading on D2 to less than 1000 pF.
Functional Description
The internal architecture is shown in the block diagram.
Data paths are illustrated in simplified form to depict how
the various logic elements communicate with each other in
implementing the instruction set of the device.
ALU and CPU Registers
The ALU can do an 8-bit addition, subtraction, logical or
shift operations in one cycle time. There are five CPU registers:
A
is the 8-bit Accumulator register
PC is the 15-bit Program Counter register
PU is the upper 7 bits of the program counter (PC)
PL is the lower 8 bits of the program counter (PC)
B
is the 8-bit address register and can be auto incremented or decremented.
X
is the 8-bit alternate address register and can be auto
incremented or decremented.
SP is the 8-bit stack pointer which points to the subroutine stack (in RAM).
B, X and SP registers are mapped into the on chip RAM.
The B and X registers are used to address the on chip RAM.
The SP register is used to address the stack in RAM during
subroutine calls and returns. The SP must be preset by software upon initialization.
Memory
Port L
TRI-STATE
Port G
TRI-STATE
Port D
HIGH
PC
CLEARED
RAM Contents
RANDOM with Power-OnReset
UNAFFECTED with external
Reset (power already applied)
B, X, SP
Same as RAM
PSW, CNTRL1, CNTRL2
and WDREG Reg.
CLEARED
Multi-Input Wakeup Reg.
WKEDG, WKEN
WKPND
CLEARED
UNKNOWN
Data and Configuration
Registers for L & G
CLEARED
WATCHDOG Timer
The memory is separated into two memory spaces: program
and data.
Prescaler/Counter each
loaded with FF
The device comes out of the HALT mode when the RESET
pin is pulled low. In this case, the user has to ensure that the
RESET signal is low long enough to allow the oscillator to
restart. An internal 256 tc delay is normally used in conjunction with the two pin crystal oscillator. When the device
comes out of the HALT mode through Multi-Input Wakeup,
this delay allows the oscillator to stabilize.
The following additional actions occur after the device
comes out of the HALT mode through the RESET pin.
If a two pin crystal/resonator oscillator is being used:
PROGRAM MEMORY
Program memory consists of 1024 x 8 ROM. These bytes of
ROM may be instructions or constant data. The memory is
addressed by the 15-bit program counter (PC). ROM can be
indirectly read by the LAID instruction for table lookup.
DATA MEMORY
The data memory address space includes on chip RAM, I/O
and registers. Data memory is addressed directly by the instruction or indirectly through B, X and SP registers. The
device has 64 bytes of RAM. Sixteen bytes of RAM are
mapped as ‘‘registers’’, these can be loaded immediately,
decremented and tested. Three specific registers: X, B, and
SP are mapped into this space, the other registers are available for general usage.
RAM Contents
7
UNCHANGED
Timer T1 and A Contents
UNKNOWN
WATCHDOG Timer Prescaler/Counter
ALTERED
http://www.national.com
Functional Description (Continued)
RESET as long as VCC is below the Brown Out Voltage. The
Device will resume execution if VCC rises above the Brown
Out Voltage. If a two pin crystal/resonator clock option is
selected, the Brown Out reset will trigger a 256tc delay. This
delay allows the oscillator to stabilize before the device exits the reset state. The delay is not used if the clock option is
either R/C or external clock. The contents of data registers
and RAM are unknown following a Brown Out reset. The
external reset takes priority over Brown Out Reset and will
deactivate the 256 tc cycles delay if in progress. The Brown
Out reset takes priority over the WATCHDOG reset.
The following actions occur as a result of Brown Out reset:
If the external or RC Clock option is being used:
RAM Contents
UNCHANGED
Timer T1 and A Contents
UNCHANGED
WATCHDOG Timer Prescaler/Counter
ALTERED
The external RESET takes priority over the Brown Out Reset.
Note: If the RESET pin is pulled low while Brown Out occurs (Brown Out
circuit has detected Brown Out condition), the external reset will not
occur until the Brown Out condition is removed. External reset has
priority only if VCC is greater than the Brown Out voltage.
RC l 5 c Power Supply Rise Time
TL/DD/11208–6
FIGURE 4. Recommended Reset Circuit
WATCHDOG RESET
With WATCHDOG enabled, the WATCHDOG logic resets
the device if the user program does not service the WATCHDOG timer within the selected service window. The
WATCHDOG reset does not disable the WATCHDOG.
Upon WATCHDOG reset, the WATCHDOG Prescaler/
Counter are each initialized with FF Hex.
The following actions occur upon WATCHDOG reset that
are different from external reset.
WDREN WATCHDOG Reset Enable bit
UNCHANGED
WDUDF WATCHDOG Underflow bit
UNCHANGED
Additional initialization actions that occur as a result of
WATCHDOG reset are as follows:
Port L
TRI-STATE
Port G
TRI-STATE
Port D
HIGH
PC
CLEARED
Ram Contents
UNCHANGED
B, X, SP
UNCHANGED
Data and Configuration
Registers for L & G
WATCHDOG Timer
TRI-STATE
Port D
HIGH
PC
CLEARED
RAM Contents
RANDOM
B, X, SP
UNKNOWN
PSW, CNTRL1, CNTRL2
and WDREG Registers
CLEARED
Multi-Input Wakeup Registers
WKEDG, WKEN
WKPND
CLEARED
UNKNOWN
Data and Configuration
Registers for L & G
CLEARED
WATCHDOG Timer
Prescalar/Counter each
loaded with FF
Timer T1 and Accumulator
Unknown data after
coming out of the HALT
(through Brown Out
Reset) with any Clock
option
Brown Out Detection
An on-board detection circuit monitors the operating voltage
(VCC) and compares it with the minimum operating voltage
specified. The Brown Out circuit is designed to reset the
device if the operating voltage is below the Brown Out voltage (between 1.8V to 4.2V at b40§ C to a 85§ C). The Minimum operating voltage for the device is 2.5V with Brown
Out disabled, but with BROWN OUT enabled the device is
guaranteed to operate properly down to minimum Brown
Out voltage (Max frequency 4 MHz), For temperature range
of 0§ C to 70§ C the Brown Out voltage is expected to be
between 1.9V to 3.9V. The circuit can be enabled or disabled by Brown Out mask option. If the device is intended to
operate at lower VCC (lower than Brown Out voltage VBO
max), the Brown Out circuit should be disabled by the mask
option.
The Brown Out circuit may be used as a power-up reset
provided the power supply rise time is slower than 50 ms (0V
to 6.0V).
CLEARED
UNKNOWN
CLEARED
Prescalar/Counter
each loaded with FF
BROWN OUT RESET
The on-board Brown Out protection circuit resets the device
when the operating voltage (VCC) is lower than the Brown
Out voltage. The device is held in reset when VCC stays
below the Brown Out Voltage. The device will remain in
http://www.national.com
TRI-STATE
Port G
Note: The development system will detect the BROWN OUT RESET externally and will force the RESET pin low. The Development System
does not emulate the 256tc delay.
PSW, CNTRL1 and CNTRL2 (except
WDUDF Bit) Registers
CLEARED
Multi-Input Wakeup Registers
WKEDG, WKEN
WKPND
Port L
Note: Brown Out Circuit is active in HALT mode (with the Brown Out mask
option selected).
8
Functional Description (Continued)
Oscillator Circuits
EXTERNAL OSCILLATOR
CKI can be driven by an external clock signal provided it
meets the specified duty cycle, rise and fall times, and input
levels. CKO is available as a general purpose input G7
and/or Halt control.
CRYSTAL OSCILLATOR
By selecting CKO as a clock output, CKI and CKO can be
connected to create a crystal controlled oscillator. Table I
shows the component values required for various standard
crystal values.
R/C OSCILLATOR
By selecting CKI as a single pin oscillator, CKI can make a
R/C oscillator. CKO is available as a general purpose input
and/or HALT control. Table II shows variation in the oscillator frequencies as functions of the component (R and C)
values.
TL/DD/11208 – 7
FIGURE 5. Clock Oscillator Configurations
TABLE I. Crystal Oscillator Configuration
R1
(kX)
R2
(MX)
C1
(pF)
C2
(pF)
CKI Freq.
(MHz)
Conditions
0
1
30
30 – 36
10
VCC e 5V
0
1
30
30 – 36
4
VCC e 5V
5.6
1
100
100 – 156
0.455
VCC e 5V
TABLE II. RC Oscillator Configuration (Part-To-Part Variation)
R
(kX)
C
(pF)
CK1 Freq.
(MHz)
Instr. Cycle
(ms)
Conditions
3.3
82
2.2 to 2.7
3.7 to 4.6
VCC e 5V
5.6
100
1.1 to 1.3
7.4 to 9.0
VCC e 5V
6.8
100
0.9 to 1.1
8.8 to 10.8
VCC e 5V
9
http://www.national.com
Functional Description (Continued)
is clocked only when the oscillator has a sufficiently large
amplitude to meet the Schmitt trigger specs. This Schmitt
trigger is not part of the oscillator closed loop. The start-up
timeout from the WATCHDOG timer enables the clock signals to be routed to the rest of the chip. The delay is not
activated when the device comes out of HALT mode
through RESET pin. Also, if the clock option is either RC or
External clock, the delay is not used, but the WATCHDOG
Prescaler/-Counter contents are changed. The Development System will not emulate the 256tc delay.
The RESET pin or Brown Out will cause the device to reset
and start executing from address X’0000. A low to high transition on the G7 pin (if single pin oscillator is used) or MultiInput Wakeup will cause the device to start executing from
the address following the HALT instruction.
When RESET pin is used to exit the device from the HALT
mode and the two pin crystal/resonator (CKI/CKO) clock
option is selected, the contents of the Accumulator and the
Timer T1 are undetermined following the reset. All other
information except the WATCHDOG Prescaler/Counter
contents is retained until continuing. If the device comes out
of the HALT mode through Brown Out reset, the contents of
data registers and RAM are unknown following the reset. All
information except the WATCHDOG Prescaler/Counter
contents is retained if the device exits the HALT mode
through G7 pin or Multi-Input Wakeup.
G7 is the HALT-restart pin, but it can still be used as an
input. If the device is not halted, G7 can be used as a general purpose input.
If the Brown Out Enable mask option is selected, the Brown
Out circuit remains active during the HALT mode causing
additional current to be drawn.
Halt Mode
The device is a fully static device. The device enters the
HALT mode by writing a one to the G7 bit of the G data
register. Once in the HALT mode, the internal circuitry does
not receive any clock signal and is therefore frozen in the
exact state it was in when halted. In this mode the chip will
only draw leakage current (output current and DC current
due to the Brown Out circuit if Brown Out is enabled).
The device supports four different methods of exiting the
HALT mode. The first method is with a low to high transition
on the CKO (G7) pin. This method precludes the use of the
crystal clock configuration (since CKO is a dedicated output). It may be used either with an RC clock configuration or
an external clock configuration. The second method of exiting the HALT mode is with the multi-Input Wakeup feature
on the L port. The third method of exiting the HALT mode is
by pulling the RESET input low. The fourth method is with
the operating voltage going below Brown Out voltage (if
Brown Out is enabled by mask option).
If the two pin crystal/resonator oscillator is being used and
Multi-Input Wakeup or Brown Out causes the device to exit
the HALT mode, the WAKEUP signal does not allow the
chip to start running immediately since crystal oscillators
have a delayed start up time to reach full amplitude and
freuqency stability. The WATCHDOG timer (consisting of an
8-bit prescaler followed by an 8-bit counter) is used to generate a fixed delay of 256tc to ensure that the oscillator has
indeed stabilized before allowing instruction execution. In
this case, upon detecting a valid WAKEUP signal only the
oscillator circuitry is enabled. The WATCHDOG Counter and
Prescaler are each loaded with a value of FF Hex. The
WATCHDOG prescaler is clocked with the tc instruction cycle. (The tc clock is derived by dividing the oscillator clock
down by a factor of 10). The Schmitt trigger following the
CKI inverter on the chip ensures that the WATCHDOG timer
http://www.national.com
Note: To allow clock resynchronization, it is necessary to program two
NOP’s immediately after the device comes out of the HALT mode.
The user must program two NOP’s following the ‘‘enter HALT mode’’
(set G7 data bit) instruction.
10
Functional Description (Continued)
TABLE III
MICROWIRE/PLUS
MICROWIRE/PLUS is a serial synchronous bidirectional
communications interface. The MICROWIRE/PLUS capability enables the device to interface with any of National
Semiconductor’s MICROWIRE peripherals (i.e. A/D converters, display drivers, EEPROMS, etc.) and with other microcontrollers which support the MICROWIRE/PLUS interface. It consists of an 8-bit serial shift register (SIO) with
serial data input (SI), serial data output (SO) and serial shift
clock (SK). Figure 6 shows the block diagram of the MICROWIRE/PLUS interface.
SL1
SL0
SK Cycle Time
0
0
1
0
1
x
2tc
4tc
8tc
where,
tc is the instruction cycle time.
MICROWIRE/PLUS OPERATION
Setting the BUSY bit in the PSW register causes the MICROWIRE/PLUS arrangement to start shifting the data. It
gets reset when eight data bits have been shifted. The user
may reset the BUSY bit by software to allow less than 8 bits
to shift. The device may enter the MICROWIRE/PLUS
mode either as a Master or as a Slave. Figure 7 shows how
two device microcontrollers and several peripherals may be
interconnected using the MICROWIRE/PLUS arrangement.
Master MICROWIRE/PLUS Operation
In the MICROWIRE/PLUS Master mode of operation the
shift clock (SK) is generated internally by the device. The
MICROWIRE/PLUS Master always initiates all data exchanges (Figure 7). The MSEL bit in the CNTRL register
must be set to enable the SO and SK functions on the G
Port. The SO and SK pins must also be selected as outputs
by setting appropriate bits in the Port G configuration register. Table IV summarizes the bit settings required for Master
mode of operation.
TL/DD/11208 – 8
FIGURE 6. MICROWIRE/PLUS Block Diagram
The shift clock can be selected from either an internal
source or an external source. Operating the MICROWIRE/
PLUS interface with the internal clock source is called the
Master mode of operation. Operating the MICROWIRE/
PLUS interface with an external shift clock is called the
Slave mode of operation.
The CNTRL register is used to configure and control the
MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS ,
the MSEL bit in the CNTRL register is set to one. The SK
clock rate is selected by the two bits, SL0 and SL1, in the
CNTRL register. Table III details the different clock rates
that may be selected.
SLAVE MICROWIRE/PLUS OPERATION
In the MICROWIRE/PLUS Slave mode of operation the SK
clock is generated by an external source. Setting the MSEL
bit in the CNTRL register enables the SO and SK functions
on the G Port. The SK pin must be selected as an input and
the SO pin selected as an output pin by appropriately setting
up the Port G configuration register. Table IV summarizes
the settings required to enter the Slave mode of operation.
TL/DD/11208 – 23
FIGURE 7. MICROWIRE/PLUS Application
11
http://www.national.com
MODE 1. TIMER WITH AUTO-LOAD REGISTER
Functional Description (Continued)
In this mode of operation, the timer T1 counts down at the
instruction cycle rate. Upon underflow the value in the register R1 gets automatically reloaded into the timer which continues to count down. The timer underflow can be programmed to interrupt the microcontroller. A bit in the control
register CNTRL enables the TIO (G3) pin to toggle upon
timer underflows. This allows the generation of square-wave
outputs or pulse width modulated outputs under software
control (Figure 8) .
The user must set the BUSY flag immediately upon entering
the Slave mode. This will ensure that all data bits sent by
the Master will be shifted properly. After eight clock pulses
the BUSY flag will be cleared and the sequence may be
repeated.
TABLE IV
G4
G5
G4
G5
G6
Fun.
Fun.
Fun.
SO
Int. SK
SI
MICROWIRE Master
TRI-STATE Int. SK
SI
MICROWIRE Master
Ext. SK
SI
MICROWIRE Slave
TRI-STATE Ext. SK
SI
MICROWIRE Slave
Config. Config.
Bit
Bit
1
1
0
1
1
0
0
0
SO
Operation
MODE 2. EXTERNAL COUNTER
In this mode, the timer T1 becomes a 16-bit external event
counter. The counter counts down upon an edge on the TIO
pin. Control bits in the register CNTRL program the counter
to decrement either on a positive edge or on a negative
edge. Upon underflow the contents of the register R1 are
automatically copied into the counter. The underflow can
also be programmed to generate an interrupt (Figure 9) .
Timer/Counter
The device has a powerful 16-bit timer with an associated
16-bit register enabling it to perform extensive timer functions. The timer T1 and its register R1 are each organized
as two 8-bit read/write registers. Control bits in the register
CNTRL allow the timer to be started and stopped under
software control. The timer-register pair can be operated in
one of three possible modes. Table V details various timer
operating modes and their requisite control settings.
TL/DD/11208 – 24
FIGURE 8. Timer/Counter Auto
Reload Mode Block Diagram
TABLE V. Timer Operating Modes
CNTRL
Bits
765
Operation Mode
T Interrupt
Timer
Counts
On
000
001
010
011
100
101
110
111
External Counter w/Auto-Load Reg.
External Counter w/Auto-Load Reg.
Not Allowed
Not Allowed
Timer w/Auto-Load Reg.
Timer w/Auto-Load Reg./Toggle TIO Out
Timer w/Capture Register
Timer w/Capture Register
Timer Underflow
Timer Underflow
Not Allowed
Not Allowed
Timer Underflow
Timer Underflow
TIO Pos. Edge
TIO Neg. Edge
TIO Pos. Edge
TIO Neg. Edge
Not Allowed
Not Allowed
tc
tc
tc
tc
TL/DD/11208 – 29
FIGURE 9. Timer in External Event Counter Mode
http://www.national.com
12
Timer/Counter (Continued)
Watchdog
MODE 3. TIMER WITH CAPTURE REGISTER
Timer T1 can be used to precisely measure external frequencies or events in this mode of operation. The timer T1
counts down at the instruction cycle rate. Upon the occurrence of a specified edge on the TIO pin the contents of the
timer T1 are copied into the register R1. Bits in the control
register CNTRL allow the trigger edge to be specified either
as a positive edge or as a negative edge. In this mode the
user can elect to be interrupted on the specified trigger
edge (Figure 10) .
The device has an on-board 8-bit WATCHDOG timer. The
timer contains an 8-bit READ/WRITE down counter clocked
by an 8-bit prescaler. Under software control the timer can
be dedicated for the WATCHDOG or used as a general purpose counter. Figure 12 shows the WATCHDOG timer block
diagram.
MODE 1: WATCHDOG TIMER
The WATCHDOG is designed to detect user programs getting stuck in infinite loops resulting in loss of program control or ‘‘runaway’’ programs. The WATCHDOG can be enabled or disabled (only once) after the device is reset as a
result of brown out reset or external reset. On power-up the
WATCHDOG is disabled. The WATCHDOG is enabled by
writing a ‘‘1’’ to WDREN bit (resides in WDREG register).
Once enabled, the user program should write periodically
into the 8-bit counter before the counter underflows. The
8-bit counter (WDCNT) is memory mapped at address 0CE
Hex. The counter is loaded with n-1 to get n counts. The
counter underflow resets the device, but does not disable
the WATCHDOG. Loading the 8-bit counter initializes the
prescaler with FF Hex and starts the prescaler/counter.
Prescaler and counter are stopped upon counter underflow.
Prescaler and counter are each loaded with FF Hex when
the device goes into the HALT mode. The prescaler is used
for crystal/resonator start-up when the device exits the
HALT mode through Multi-Input Wakeup. In this case, the
prescaler/counter contents are changed.
TL/DD/11208 – 25
FIGURE 10. Timer Capture Mode Block Diagram
TIMER PWM APPLICATION
Figure 11 shows how a minimal component D/A converter
can be built out of the Timer-Register pair in the Auto-Reload mode. The timer is placed in the ‘‘Timer with auto reload’’ mode and the TIO pin is selected as the timer output.
At the outset the TIO pin is set high, the timer T1 holds the
on time and the register R1 holds the signal off time. Setting
TRUN bit starts the timer which counts down at the instruction cycle rate. The underflow toggles the TIO output and
copies the off time into the timer, which continues to run. By
alternately loading in the on time and the off time at each
successive interrupt a PWM frequency can be easily generated.
MODE 2: TIMER
In this mode, the prescaler/counter is used as a timer by
keeping the WDREN (WATCHDOG reset enable) bit at 0.
The counter underflow sets the WDUDF (underflow) bit and
the underflow does not reset the device. Loading the 8-bit
counter (load n-1 for n counts) sets the WDTEN bit
(WATCHDOG Timer Enable) to ‘‘1’’, loads the prescaler
with FF, and starts the timer. The counter underflow stops
the timer. The WDTEN bit serves as a start bit for the
WATCHDOG timer. This bit is set when the 8-bit counter is
loaded by the user program. The load could be as a result of
WATCHDOG service (WATCHDOG timer dedicated for
WATCHDOG function) or write to the counter (WATCHDOG
timer used as a general purpose counter). The bit is cleared
upon Brown Out reset, WATCHDOG reset or external reset.
The bit is not memory mapped and is transparent to the
user program.
TL/DD/11208 – 26
FIGURE 11. Timer Application
TABLE VI. WATCHDOG Control/Status
HALT
Mode
WD
Reset
EXT/BOR
Reset
(Note 1)
8-Bit Prescaler
FF
FF
FF
FF
8-Bit WD Counter
FF
FF
FF
User Value
Parameter
Counter
Load
WDREN Bit
Unchanged
Unchanged
0
No Effect
WDUDF Bit
0
Unchanged
0
0
Unchanged
0
0
1
WDTEN Signal
Note 1: BOR is Brown Out Reset.
13
http://www.national.com
Functional Description (Continued)
WDREN: WD Reset Enable
WDREN bit resides in a separate register (bit 0 of WDREG).
This bit enables the WATCHDOG timer to generate a reset.
The bit is cleared upon Brown Out reset, or external reset.
The bit under software control can be written to only once
(once written to, the hardware does not allow the bit to be
changed during program execution).
WDREN e 1 WATCHDOG reset is enabled.
WDREN e 0 WATCHDOG reset is disabled.
Table VI shows the impact of Brown Out Reset, WATCHDOG Reset, and External Reset on the Control/Status bits.
CONTROL/STATUS BITS
WDUDF: WATCHDOG Timer Underflow Bit
This bit resides in the CNTRL2 Register. The bit is set when
the WATCHDOG timer underflows. The underflow resets
the device if the WATCHDOG reset enable bit is set
(WDREN e 1). Otherwise, WDUDF can be used as the timer underflow flag. The bit is cleared upon Brown-Out reset,
external reset, load to the 8-bit counter, or going into the
HALT mode. It is a read only bit.
TL/DD/11208 – 15
FIGURE 12. WATCHDOG Timer Block Diagram
http://www.national.com
14
Modulator/Timer
The Modulator/Timer contains an 8-bit counter and an 8-bit
autoreload register (MODRL address 0CF Hex). The Modulator/Timer has two modes of operation, selected by the
control bit MC3. The Modulator/Timer Control bits MC1,
MC2 and MC3 reside in CNTRL2 Register.
control bit by software loads the counter with the value of
the autoreload register and starts the counter. The counter
underflow toggles the (L7) output pin. The 50% duty cycle
signal will be continuously generated until MC1 is reset by
the user program.
MODE 1: MODULATOR
The Modulator is used to generate high frequency pulses on
the modulator output pin (L7). The L7 pin should be configured as an output. The number of pulses is determined by
the 8-bit down counter. Under software control the modulator input clock can be either CKI or tC. The tC clock is derived by dividing down the oscillator clock by a factor of 10.
Three control bits (MC1, MC2, and MC3) are used for the
Modulator/Timer output control. When MC2 e 1 and MC3
e 1, CKI is used as the modulator input clock. When MC2
e 0, and MC3 e 1, tC is used as the modulator input clock.
The user loads the counter with the desired number of
counts (256 max) and sets MC1 to start the counter. The
modulator autoreload register is loaded with n-1 to get n
pulses. CKI or tc pulses are routed to the modulator output
(L7) until the counter underflows (Figure 13). Upon underflow the hardware resets MC1 and stops the counter. The
L7 pin goes low and stays low until the counter is restarted
by the user program. The user program has the responsibility to timeout the low time. Unless the number of counts is
changed, the user program does not have to load the counter each time the counter is started. The counter can simply
be started by setting the MC1 bit. Setting MC1 by software
will load the counter with the value of the autoreload register. The software can reset MC1 to stop the counter.
b. Variable Duty Cycle:
When MC3 e 0 and MC2 e 1, a variable duty cycle PWM
signal is generated on the L7 output pin. The counter is
clocked by tC. In this mode the 16-bit timer T1 along with
the 8-bit down counter are used to generate a variable duty
cycle PWM signal. The timer T1 underflow sets MC1 which
starts the down counter and it also sets L7 high (L7 should
be configured as an output).When the counter underflows
the MC1 control bit is reset and the L7 output will go low
until the next timer T1 underflow. Therefore, the width of the
output pulse is controlled by the 8-bit counter and the pulse
duration is controlled by the 16-bit timer T1 (Figure 15). Timer T1 must be configured in ‘‘PWM Mode/Toggle TIO Out’’
(CNTRL1 Bits 7,6,5 e 101).
Table VII shows the different operation modes for the Modulator/Timer.
TABLE VII. Modulator/Timer Modes
Control Bits in
CNTRL2(00CC)
MODE 2: PWM TIMER
The counter can also be used as a PWM Timer. In this
mode, an 8-bit register is used to serve as an autoreload
register (MODRL).
a. 50% Duty Cycle:
When MC1 is 1 and MC2, MC3 are 0, a 50% duty cycle free
running signal is generated on the L7 output pin (Figure 14).
The L7 pin must be configured as an output pin. In this
mode the 8-bit counter is clocked by tC. Setting the MC1
Operation Mode
L7 Function
MC3
MC2
MC1
0
0
0
Normal I/O
0
0
1
50% Duty Cycle Mode (Clocked
by tc)
0
1
X
Variable Duty Cycle Mode
(Clocked by tc) Using Timer 1
Underflow
1
0
X
Modulator Mode (Clocked by tc)
1
1
X
Modulator Mode (Clocked by
CKI)
Note: MC1, MC2 and MC3 control bits are cleared upon reset.
Internal Data Bus
TL/DD/11208 – 16
FIGURE 13. Mode 1: Modulator Block Diagram/Output Waveform
15
http://www.national.com
Modulator/Timer (Continued)
TL/DD/11208 – 17
TL/DD/11208 – 18
FIGURE 14. Mode 2a: 50% Duty Cycle Output
TL/DD/11208 – 19
TL/DD/11208 – 20
FIGURE 15. Mode 2b: Variable Duty Cycle Output
http://www.national.com
16
the edge select change in WKEDG. Next, the associated
WKPND bit should be cleared, followed by the associated
WKEN bit being re-enabled.
Comparator
The device has one differential comparator. Ports L0 – L2
are used for the comparator. The output of the comparator
is brought out to a pin. Port L has the following assignments:
An example may serve to clarify this procedure. Suppose
we wish to change the edge select from positive (low going
high) to negative (high going low) for L port bit 5, where bit 5
has previously been enabled for an input. The program
would be as follows:
RBIT 5,WKEN
SBIT 5,WKEDG
RBIT 5,WKPND
SBIT 5,WKEN
If the L port bits have been used as outputs and then
changed to inputs with Multi-Input Wakeup, a safety procedure should also be followed to avoid inherited pseudo
wakeup conditions. After the selected L port bits have been
changed from output to input but before the associated
WKEN bits are enabled, the associated edge select bits in
WKEDG should be set or reset for the desired edge selects,
followed by the associated WKPND bits being cleared. This
same procedure should be used following RESET, since the
L port inputs are left floating as a result of RESET.
The occurrence of the selected trigger condition for Multi-Input Wakeup is latched into a pending register called
Reg:WKPND. The respective bits of the WKPND register
will be set on the occurrence of the selected trigger edge on
the corresponding Port L pin. The user has the responsibility
of clearing these pending flags. Since the Reg:WKPND is a
pending register for the occurrence of selected wakeup
conditions, the device will not enter the HALT mode if any
Wakeup bit is both enabled and pending. Setting the G7
data bit under this condition will not allow the device to enter the HALT mode. Consequently, the user has the responsibility of clearing the pending flags before attempting to
enter the HALT mode.
If a crystal oscillator is being used, the Wakeup signal will
not start the chip running immediately since crystal oscillators have a finite start up time. The WATCHDOG timer prescaler generates a fixed delay to ensure that the oscillator
has indeed stabilized before allowing the device to execute
instructions. In this case, upon detecting a valid Wakeup
signal only the oscillator circuitry and the WATCHDOG timer
are enabled. The WATCHDOG timer prescaler is loaded
with a value of FF Hex (256 counts) and is clocked from the
tc instruction cycle clock. The tc clock is derived by dividing
down the oscillator clock by a factor of 10. A Schmitt trigger
following the CKI on chip inverter ensures that the WATCHDOG timer is clocked only when the oscillator has a sufficiently large amplitude to meet the Schmitt trigger specs.
This Schmitt trigger is not part of the oscillator closed loop.
The startup timeout from the WATCHDOG timer enables
the clock signals to be routed to the rest of the chip.
L0 Comparator output
L1 Comparator negative input
L2 Comparator positive input
THE COMPARATOR STATUS/CONTROL BITS
These bits reside in the CNTRL2 Register (Address 0CC)
CMPEN
Enables comparator (‘‘1’’ e enable)
CMPRD
Reads comparator output internally
(CMPEN e 1, CMPOE e X)
CMPOE
Enables comparator output to pin L0
(‘‘1’’ e enable), CMPEN bit must be set to enable this function. If CMPEN e 0, L0 will be 0.
The Comparator Select/Control bits are cleared on RESET
(the comparator is disabled). To save power the program
should also disable the comparator before the device enters
the HALT mode.
The user program must set up L0, L1 and L2 ports correctly
for comparator Inputs/Output: L1 and L2 need to be configured as inputs and L0 as output.
Multi-Input Wake Up
The Multi-Input Wakeup feature is used to return (wakeup)
the device from the HALT mode. Figure 16 shows the MultiInput Wakeup logic.
This feature utilizes the L Port. The user selects which particular L port bit or combination of L Port bits will cause the
device to exit the HALT mode. Three 8-bit memory mapped
registers, Reg:WKEN, Reg:WKEDG, and Reg:WKPND are
used in conjunction with the L port to implement the MultiInput Wakeup feature.
All three registers Reg:WKEN, Reg:WKPND, and
Reg:WKEDG are read/write registers, and are cleared at
reset, except WKPND. WKPND is unknown on reset.
The user can select whether the trigger condition on the
selected L Port pin is going to be either a positive edge (low
to high transition) or a negative edge (high to low transition).
This selection is made via the Reg:WKEDG, which is an 8bit control register with a bit assigned to each L Port pin.
Setting the control bit will select the trigger condition to be a
negative edge on that particular L Port pin. Resetting the bit
selects the trigger condition to be a positive edge. Changing
an edge select entails several steps in order to avoid a
pseudo Wakeup condition as a result of the edge change.
First, the associated WKEN bit should be reset, followed by
17
http://www.national.com
Multi-Input Wakeup (Continued)
The software interrupt does not reset the GIE bit. This
means that the controller can be interrupted by other interrupt sources while servicing the software interrupt.
INTERRUPT PROCESSING
The interrupt, once acknowledged, pushes the program
counter (PC) onto the stack and the stack pointer (SP) is
decremented twice. The Global Interrupt Enable (GIE) bit is
reset to disable further interrupts. The microcontroller then
vectors to the address 00FFH and resumes execution from
that address. This process takes 7 cycles to complete. At
the end of the interrupt subroutine, any of the following
three instructions return the processor back to the main program: RET, RETSK or RETI. Either one of the three instructions will pop the stack into the program counter (PC). The
stack pointer is then incremented twice. The RETI instruction additionally sets the GIE bit to re-enable further interrupts.
Any of the three instructions can be used to return from a
hardware interrupt subroutine. The RETSK instruction
should be used when returning from a software interrupt
subroutine to avoid entering an infinite loop.
TL/DD/11208–21
FIGURE 16. Multi-Input Wakeup Logic
Note: There is always the possibility of an interrupt occurring during an instruction which is attempting to reset the GIE bit or any other interrupt
enable bit. If this occurs when a single cycle instruction is being used
to reset the interrupt enable bit, the interrupt enable bit will be reset
but an interrupt may still occur. This is because interrupt processing is
started at the same time as the interrupt bit is being reset. To avoid
this scenario, the user should always use a two, three, or four cycle
instruction to reset interrupt enable bits.
INTERRUPTS
The device has a sophisticated interrupt structure to allow
easy interface to the real world. There are three possible
interrupt sources, as shown below.
A maskable interrupt on external G0 input (positive or negative edge sensitive under software control)
A maskable interrupt on timer carry or timer capture
A non-maskable software/error interrupt on opcode zero
DETECTION OF ILLEGAL CONDITIONS
The device incorporates a hardware mechanism that allows
it to detect illegal conditions which may occur from coding
errors, noise, and ‘‘brown out’’ voltage drop situations. Specifically, it detects cases of executing out of undefined ROM
area and unbalanced tack situations.
Reading an undefined ROM location returns 00 (hexadecimal) as its contents. The opcode for a software interrupt is
also ‘‘00’’. Thus a program accessing undefined ROM will
cause a software interrupt.
Reading an undefined RAM location returns an FF (hexadecimal). The subroutine stack on the device grows down for
each subroutine call. By initializing the stack pointer to the
top of RAM, the first unbalanced return instruction will cause
the stack pointer to address undefined RAM. As a result the
program will attempt to execute from FFFF (hexadecimal),
which is an undefined ROM location and will trigger a software interrupt.
INTERRUPT CONTROL
The GIE (global interrupt enable) bit enables the interrupt
function. This is used in conjunction with ENI and ENTI to
select one or both of the interrupt sources. This bit is reset
when interrupt is acknowledged.
ENI and ENTI bits select external and timer interrupts respectively. Thus the user can select either or both sources
to interrupt the microcontroller when GIE is enabled.
IEDG selects the external interrupt edge (0 e rising edge,
1 e falling edge). The user can get an interrupt on both
rising and falling edges by toggling the state of IEDG bit
after each interrupt.
IPND and TPND bits signal which interrupt is pending. After
an interrupt is acknowledged, the user can check these two
bits to determine which interrupt is pending. This permits the
interrupts to be prioritized under software. The pending flags
have to be cleared by the user. Setting the GIE bit high
inside the interrupt subroutine allows nested interrupts.
TL/DD/11208 – 27
FIGURE 17. Interrupt Block Diagram
http://www.national.com
18
Control Registers
The Half-Carry bit is also effected by all the instructions that
effect the Carry flag. The flag values depend upon the instruction. For example, after executing the ADC instruction
the values of the Carry and the Half-Carry flag depend upon
the operands involved. However, instructions like SET C
and RESET C will set and clear both the carry flags. Table
XIII lists the instructions that effect the HC and the C flags.
CNTRL1 REGISTER (ADDRESS 00EE)
The Timer and MICROWIRE control register contains the
following bits:
SL1 and SL0 Select the MICROWIRE clock divide-by
(00 e 2, 01 e 4, 1x e 8)
IEDG
MSEL
External interrupt edge polarity select
Selects G5 and G4 as MICROWIRE signals
SK and SO respectively
Used to start and stop the timer/counter
(1 e run, 0 e stop)
Timer T1 Mode Control Bit
Timer T1 Mode Control Bit
Timer T1 Mode Control Bit
TRUN
TC1
TC2
TC3
Bit 7
TC1
TC2
TC3
TRUN
MSEL
IEDG
SL1
TABLE XIII. Instructions Effecting HC and C Flags
Instr.
HC
Depends on Operands Depends on Operands
SUBC
Depends on Operands Depends on Operands
SET C
Set
Set
Bit 0
RESET C Set
Set
SL0
RRC
TPND
ENTI
IPND
BUSY
ENI
Depends on Operands Depends on Operands
CNTRL2 REGISTER (ADDRESS 00CC)
Bit 7
Bit 0
MC3
MC2
MC1 CMPEN CMPRD CMPOE WDUDF
R/W
R/W
R/W
MC3
MC2
MC1
CMPEN
CMPRD
CMPOE
WDUDF
Bit 0
C
C Flag
ADC
PSW REGISTER (ADDRESS 00EF)
The PSW register contains the following select bits:
GIE
Global interrupt enable (enables interrupts)
ENI
External interrupt enable
BUSY MICROWIRE busy shifting flag
PND External interrupt pending
ENTI Timer T1 interrupt enable
TPND Timer T1 interrupt pending
(timer Underflow or capture edge)
C
Carry Flip/Flop
HC
Half-Carry Flip/Flop
Bit 7
HC Flag
R/W
R/O
R/W
R/O
unused
Modulator/Timer Control Bit
Modulator/Timer Control Bit
Modulator/Timer Control Bit
Comparator Enable Bit
Comparator Read Bit
Comparator Output Enable Bit
WATCHDOG Timer Underflow Bit (Read Only)
GIE
WDREG REGISTER (ADDRESS 00CD)
WDREN WATCHDOG Reset Enable Bit (Write Once Only)
Bit 7
Bit 0
UNUSED
19
WDREN
http://www.national.com
Memory Map
Addressing Modes
All RAM, ports and registers (except A and PC) are mapped
into data memory address space.
There are ten addressing modes, six for operand addressing and four for transfer of control.
TABLE IX. Memory Map
OPERAND ADDRESSING MODES
REGISTER INDIRECT
This is the ‘‘normal’’ addressing mode for the chip. The operand is the data memory addressed by the B or X pointer.
REGISTER INDIRECT WITH AUTO POST INCREMENT OR
DECREMENT
This addressing mode is used with the LD and X instructions. The operand is the data memory addressed by the B
or X pointer. This is a register indirect mode that automatically post increments or post decrements the B or X pointer
after executing the instruction.
DIRECT
The instruction contains an 8-bit address field that directly
points to the data memory for the operand.
IMMEDIATE
The instruction contains an 8-bit immediate field as the operand.
SHORT IMMEDIATE
This addressing mode issued with the LD B,Ý instruction,
where the immediate Ý is less than 16. The instruction contains a 4-bit immediate field as the operand.
INDIRECT
This addressing mode is used with the LAID instruction. The
contents of the accumulator are used as a partial address
(lower 8 bits of PC) for accessing a data operand from the
program memory.
Address
Contents
00 to 2F
On-chip RAM bytes (48 bytes)
30 to 7F
Unused RAM Address Space (Reads as All
Ones)
80 to BF
Expansion Space for On-Chip EERAM
(Reads Undefined Data)
C0 to C7
C8
C9
CA
CB
CC
CD
CE
CF
Reserved
MIWU Edge Select Register (Reg:WKEDG)
MIWU Enable Register (Reg:WKEN)
MIWU Pending Register (Reg:WKPND)
Reserved
Control2 Register (CNTRL2)
WATCHDOG Register (WDREG)
WATCHDOG Counter (WDCNT)
Modulator Reload (MODRL)
D0
D1
D2
D3
D4
D5
D6
D7
D8 to DB
DC
DD to DF
Port L Data Register
Port L Configuration Register
Port L Input Pins (Read Only)
Reserved for Port L
Port G Data Register
Port G Configuration Register
Port G Input Pins (Read Only)
Port I Input Pins (Read Only)
Reserved for Port C
Port D Data Register
Reserved for Port D
E0 to EF
E0 to E7
E8
E9
EA
EB
EC
ED
EE
EF
On-Chip Functions and Registers
Reserved for Future Parts
Reserved
MICROWIRE Shift Register
Timer Lower Byte
Timer Upper Byte
Timer1 Autoreload Register Lower Byte
Timer1 Autoreload Register Upper Byte
CNTRL1 Control Register
PSW Register
F0 to FF
FC
FD
FE
On-Chip RAM Mapped as Registers
X Register
SP Register
B Register
TRANSFER OF CONTROL ADDRESSING MODES
RELATIVE
This mode is used for the JP instruction with the instruction
field being added to the program counter to produce the
next instruction address. JP has a range from b31 to a 32
to allow a one byte relative jump (JP a 1 is implemented by
a NOP instruction). There are no ‘‘blocks’’ or ‘‘pages’’ when
using JP since all 15 bits of the PC are used.
ABSOLUTE
This mode is used with the JMP and JSR instructions with
the instruction field of 12 bits replacing the lower 12 bits of
the program counter (PC). This allows jumping to any location in the current 4k program memory segment.
ABSOLUTE LONG
This mode is used with the JMPL and JSRL instructions with
the instruction field of 15 bits replacing the entire 15 bits of
the program counter (PC). This allows jumping to any location in the entire 32k program memory space.
INDIRECT
This mode is used with the JID instruction. The contents of
the accumulator are used as a partial address (lower 8 bits
of PC) for accessing a location in the program memory. The
contents of this program memory location serves as a partial address (lower 8 bits of PC) for the jump to the next
instruction.
Reading other unused memory locations will return undefined data.
http://www.national.com
20
Instruction Set
Symbols
[B]
Memory indirectly addressed by B register
[X]
Memory indirectly addressed by X register
Mem Direct address memory or [B]
MemI Direct address memory or [B] or Immediate data
Imm 8-bit Immediate data
Reg
Register memory: addresses F0 to FF (Includes B, X
and SP)
Bit
Bit number (0 to 7)
w Loaded with
Ý Exchanged with
REGISTER AND SYMBOL DEFINITIONS
Registers
A
8-bit Accumulator register
B
8-bit Address register
X
8-bit Address register
SP
8-bit Stack pointer register
PC
15-bit Program counter register
PU
upper 7 bits of PC
PL
lower 8 bits of PC
C
1-bit of PSW register for carry
HC
Half Carry
GIE
1-bit of PSW register for global interrupt enable
Instruction Set
A w A a MemI
A w A a MemI a C, C w Carry
HC w Half Carry
A w A a MemI a C, C w Carry
HC w Half Carry
A w A and MemI
A w A or MemI
A w A xor MemI
Compare A and MemI, Do next if A e MemI
Compare A and MemI, Do next if A l MemI
Do next if lower 4 bits of B i Imm
Reg w Reg b 1, skip if Reg goes to 0
1 to bit,
Mem (bit e 0 to 7 immediate)
0 to bit,
Mem
If bit,
Mem is true, do next instr.
ADD
ADC
add
add with carry
SUBC
subtract with carry
AND
OR
XOR
IFEQ
IFGT
IFBNE
DRSZ
SBIT
Logical AND
Logical OR
Logical Exclusive-OR
IF equal
IF greater than
IF B not equal
Decrement Reg. ,skip if zero
Set bit
RBIT
Reset bit
IFBIT
If bit
X
LD A
LD mem
LD Reg
Exchange A with memory
Load A with memory
Load Direct memory Immed.
Load Register memory Immed.
A Ý Mem
A w MemI
Mem w Imm
Reg w Imm
X
X
LD A
LD A
LD M
Exchange A with memory [B]
Exchange A with memory [X]
Load A with memory [B]
Load A with memory [X]
Load Memory Immediate
(B w B g 1)
A Ý [B]
(X w X g 1)
A Ý [X]
(B w B g 1)
A w [B]
(X w X g 1)
A w [X]
[B] w Imm (B w B g 1)
CLRA
INCA
DECA
LAID
DCORA
RRCA
SWAPA
SC
RC
IFC
IFNC
Clear A
Increment A
Decrement A
Load A indirect from ROM
DECIMAL CORRECT A
ROTATE A RIGHT THRU C
Swap nibbles of A
Set C
Reset C
If C
If not C
Aw0
AwAa1
AwAb1
A w ROM(PU,A)
A w BCD correction (follows ADC, SUBC)
C x A7 x . . . x A0 x C
A7 . . . A4 Ý A3 . . . A0
C w 1, HC w 1
C w 0, HC w 0
If C is true, do next instruction
If C is not true, do next instruction
JMPL
JMP
JP
JSRL
JSR
JID
RET
RETSK
RETI
INTR
NOP
Jump absolute long
Jump absolute
Jump relative short
Jump subroutine long
Jump subroutine
Jump indirect
Return from subroutine
Return and Skip
Return from Interrupt
Generate an interrupt
No operation
PC w ii (ii e 15 bits, 0 to 32k)
PC11..0 w i (i e 12 bits)
PC w PC a r (r is b31 to a 32, not 1)
[SP] w PL,[SP-1] w PU,SP-2,PC w ii
[SP] w PL,[SP-1] w PU,SP-2,PC11.. 0 w i
PL w ROM(PU,A)
SP a 2,PL w [SP],PU w [SP-1]
SP a 2,PL w [SP],PU w [SP-1],Skip next instruction
SP a 2,PL w [SP],PU w [SP-1],GIE w 1
[SP] w PL,[SPb1] w PU,SP-2,PC w 0FF
PC w PC a 1
21
http://www.national.com
http://www.national.com
22
JP -17
JP -16
JP -1
JP -0
D
LD 0FF,Ý1
LD 0FE,Ýi
LD 0FD,Ýi
LD 0FC,Ýi
LD 0FB,Ýi
LD 0FA,Ýi
LD 0F9,Ýi
LD 0F8,Ýi
LD 0F7,Ýi
LD 0F6,Ýi
LD 0F5,Ýi
LD 0F4,Ýi
LD 0F3,Ýi
LD 0F2,Ýi
LD 0F1,Ýi
LD 0F0,Ýi
C
B
*
LD A,
[X]
DIR
LD Md,
Ýi
LD A,
[X b]
LD A,
[X a ]
*
NOP
*
X A,
[X]
*
*
X A,
[X b]
X A,
[X a ]
*
RRCA
A
*
LD A,
[B]
JSRL
JMPL
LD A,
[Bb]
LD A,
[B a ]
*
*
*
X A,
[B]
JID
LAID
X A,
[Bb]
X A,
[B a ]
SC
RC
9
*
LD
[B], Ýi
LD A,
Md
X A,Md
LD
[Bb],Ýi
LD
[B a ],Ýi
*
LD A,
Ýi
OR A,
Ýi
XOR A,
Ýi
AND A,
Ýi
ADD A,
Ýi
IFGT A,
Ýi
IFEQ A,
Ýi
SUBC A,
Ýi
ADC A,
Ýi
8
RETI
RET
RETSK
*
DECA
INCA
IFNC
IFC
OR
A,[B]
XOR
A,[B]
AND
A,[B]
ADD
A,[B]
IFGT
A,[B]
IFEQ
A,[B]
SUBC
A,[B]
ADC A,
[B]
Md is a directly addressed memory location
DRSZ 0FF
DRSZ 0FE
DRSZ 0FD
DRSZ 0FC
DRSZ 0FB
DRSZ 0FA
DRSZ 0F9
DRSZ 0F8
DRSZ 0F7
DRSZ 0F6
DRSZ 0F5
DRSZ 0F4
DRSZ 0F3
DRSZ 0F2
DRSZ 0F1
DRSZ 0F0
is the immediate data
JP -18
JP -2
i
JP -19
JP -3
where,
JP -20
JP -24
JP -8
JP -4
JP -25
JP -9
JP -21
JP -26
JP -10
JP -5
JP -27
JP -11
JP -22
JP -28
JP -12
JP -6
JP -29
JP -13
JP -23
JP -30
JP -14
JP -7
E
JP -31
F
JP -15
RBIT
7,[B]
RBIT
6, [B]
RBIT
5,[B]
RBIT
4,[B]
RBIT
3,[B]
RBIT
2,[B]
RBIT
1,[B]
RBIT
0,[B]
*
DCORA
SWAPA
CLRA
*
*
*
*
6
5
LD B, 0
LD B, 1
LD B, 2
LD B, 3
LD B, 4
LD B, 5
LD B, 6
LD B, 7
LD B, 8
LD B, 9
LD B, 0A
LD B, 0B
LD B, 0C
LD B, 0D
LD B, 0E
LD B, 0F
4
IFBNE 0F
IFBNE 0E
IFBNE 0D
IFBNE 0C
IFBNE 0B
IFBNE 0A
IFBNE 9
IFBNE 8
IFBNE 7
IFBNE 6
IFBNE 5
IFBNE 4
IFBNE 3
IFBNE 2
IFBNE 1
IFBNE 0
* is an unused opcode (see following table)
SBIT
7,[B]
SBIT
6, [B]
SBIT
5,[B]
SBIT
4,[B]
SBIT
3,[B]
SBIT
2,[B]
SBIT
1,[B]
SBIT
0,[B]
IFBIT
7,[B]
IFBIT
6,[B]
IFBIT
5,[B]
IFBIT
4,[B]
IFBIT
3,[B]
IFBIT
2,[B]
IFBIT
1,[B]
IFBIT
0,[B]
7
Bits 7 – 4
3
JSR
0F00 –0FFF
JSR
0E00 –0EFF
JSR
0D00 –0DFF
JSR
0C00 –0CFF
JSR
0B00 –0BFF
JSR
0A00 –0AFF
JSR
0900 –09FF
JSR
0800 –08FF
JSR
0700 –07FF
JSR
0600 –06FF
JSR
0500 –05FF
JSR
0400 –04FF
JSR
0300 –03FF
JSR
0200 –02FF
JSR
0100 –01FF
JSR
0000 –00FF
2
JMP
0F00 –0FFF
JMP
0E00 –0EFF
JMP
0D00 –0DFF
JMP
0C00 –0CFF
JMP
0B00 –0BFF
JMP
0A00 –0AFF
JMP
0900 –09FF
JMP
0800 –08FF
JMP
0700 –07FF
JMP
0600 –06FF
JMP
0500 –05FF
JMP
0400 –04FF
JMP
0300 –03FF
JMP
0200 –02FF
JMP
0100 –01FF
JMP
0000 –00FF
1
JP a 32
JP a 31
JP a 30
JP a 29
JP a 28
JP a 27
JP a 26
JP a 25
JP a 24
JP a 23
JP a 22
JP a 21
JP a 20
JP a 19
JP a 18
JP a 17
0
JP a 16
JP a 15
JP a 14
JP a 13
JP a 12
JP a 11
JP a 10
JP a 9
JP a 8
JP a 7
JP a 6
JP a 5
JP a 4
JP a 3
JP a 2
INTR
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
OPCODE LIST
Bits 3 – 0
Instruction Execution Time
Bytes and Cycles per
Most instructions are single byte (with immediate addressInstruction
ing mode instruction taking two bytes).
The following table shows the number of bytes and cycles
Most single instructions take one cycle time to execute.
for each instruction in the format of byte/cycle.
Skipped instructions require x number of cycles to be
skipped, where x equals the number of bytes in the skipped
instruction opcode.
See the BYTES and CYCLES per INSTRUCTION table for
details.
Arithmetic Instructions (Bytes/Cycles)
[B]
Direct
Immed.
ADD
ADC
SUBC
AND
OR
XOR
IFEQ
IFGT
IFBNE
DRSZ
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
2/2
2/2
2/2
2/2
2/2
2/2
2/2
2/2
SBIT
RBIT
IFBIT
1/1
1/1
1/1
1/3
3/4
3/4
3/4
Memory Transfer Instructions (Bytes/Cycles)
Register
Register Indirect
Indirect Direct Immed.
Auto Incr & Decr
[B] [X]
[B a , Bb] [X a , Xb]
X A,*
1/1
LD A,*
1/1
LD B,Imm
LD B,Imm
LD Mem,Imm
LD Reg,Imm
1/3
1/3
2/3
2/3
2/2
1/1
2/3
3/3
1/2
1/2
1/3
1/3
(If B k 16)
(If B l 15)
2/2
2/3
* e l Memory location addressed by B or X or directly.
Instructions Using A & C
Instructions
CLRA
INCA
DECA
LAID
DCORA
RRCA
SWAPA
SC
RC
IFC
IFNC
Transfer of Control Instructions
Bytes/Cycles
Instructions
1/1
1/1
1/1
1/3
1/1
1/1
1/1
1/1
1/1
1/1
1/1
JMPL
JMP
JP
JSRL
JSR
JID
RET
RETSK
RETI
INTR
NOP
23
Bytes/Cycles
3/4
2/3
1/3
3/5
2/5
1/3
1/5
1/5
1/5
1/7
1/1
http://www.national.com
Bytes and Cycles per
Instruction (Continued)
OPTION 2: BROWN OUT
The following table shows the instructions assigned to unused opcodes. This table is for information only. The operations performed are subject to change without notice. Do
not use these opcodes.
Unused
Opcode
Instruction
60
61
62
63
67
8C
99
9F
A7
A8
NOP
NOP
NOP
NOP
NOP
RET
NOP
LD [B], Ýi
X A, [B]
NOP
Unused
Opcode
Instruction
A9
AF
B1
B4
B5
B7
B9
BF
NOP
LD A, [B]
C x HC
NOP
NOP
X A, [X]
NOP
LD A, [X]
e1
e2
Enable Brown Out Detection
Disable Brown Out Detection
OPTION 3: BONDING
e1
e2
e3
e4
28-pin
20-pin
16-pin
28-pin
DIP
DIP/SO
SO
SO
Development Support
SUMMARY
# iceMASTERTM : IM-COP8/400ÐFull feature in-circuit emulation for all COP8 products. A full set of COP8 Basic
and Feature Family device and package specific probes
are available.
# COP8 Debug Module: Moderate cost in-circuit emulation
and development programming unit.
# COP8
Evaluation and Programming Unit: EPUCOP8780Ðlow cost in-circuit simulation and development programming unit.
Option List
The mask programmable options are listed below. The options are programmed at the same time as the ROM pattern
to provide the user with hardware flexibility to a variety of
oscillation and packaging configuration.
# Assembler: COP8-DEV-IBMA. A DOS installable cross
OPTION 1: CKI INPUT
# C Compiler: COP8C. A DOS installable cross develop-
e1
e2
e3
development Assembler, Linker, Librarian and Utility
Software Development Tool Kit.
ment Software Tool Kit.
Crystal (CKI/IO) CKO for crystal configuration
External (CKI/IO) CKO available as G7 input
R/C (CKI/IO) CKO available as G7 input
http://www.national.com
# OTP/EPROM Programmer Support: Covering needs
from engineering prototype, pilot production to full production environments.
24
Development Support (Continued)
# Instruction by instruction memory/register changes dis-
IceMASTER (IM) IN-CIRCUIT EMULATION
The iceMASTER IM-COP8/400 is a full feature, PC based,
in-circuit emulation tool developed and marketed by MetaLink Corporation to support the whole COP8 family of products. National is a resale vendor for these products.
See Figure 18 for configuration.
played on source window when in single step operation.
# Single base unit and debugger software reconfigurable to
support the entire COP8 family; only the probe personality needs to change. Debugger software is processor customized, and reconfigured from a master model file.
# Processor specific symbolic display of registers and bit
The iceMASTER IM-COP8/400 with its device specific
COP8 Probe provides a rich feature set for developing, testing and maintaining product:
level assignments, configured from master model file.
# Real-time in-circuit emulation; full 2.4V–5.5V operation
# Halt/Idle mode notification.
# On-Line HELP customized to specific processor using
range, full DC-10 MHz clock. Chip options are programmable or jumper selectable.
# Includes a copy of COP8-DEV-IBMA assembler and link-
master model file.
er SDK.
# Direct connection to application board by package compatible socket or surface assembly.
IM Order Information
# Full 32 kbytes of loadable programming space that over-
Base Unit
lays (replaces) the on-chip ROM or EPROM. On-chip
RAM and I/O blocks are used directly or recreated on
the probe as necessary.
# Full 4k frame synchronous trace memory. Address, instruction, and 8 unspecified, circuit connectable trace
lines. Display can be HLL source (e.g., C source), assembly or mixed.
IM-COP8/400-1
iceMASTER Base Unit, 110V
Power Supply
IM-COP8/400-2
iceMASTER Base Unit, 220V
Power Supply
iceMASTER Probe
# A full 64k hardware configurable break, trace on, trace
MHW-840CJ20DWPC
MHW-840CJ28DWPC
off control, and pass count increment events.
# Tool set integrated interactive symbolic debuggerÐsup-
20 DIP
28 DIP
Adapters for SO Packages
ports both assembler (COFF) and C Compiler (.COD)
linked object formats.
# Real time performance profiling analysis; selectable
bucket definition.
# Watch windows, content updated automatically at each
MHW-SOIC16
16 SO
MHW-SOIC20
20 SO
MHW-SOIC28
28 SO
execution break.
TL/DD/11208 – 30
FIGURE 18. COP8 iceMASTER Environment
25
http://www.national.com
Development Support (Continued)
# Debugger software is processor customized, and recon-
iceMASTER DEBUG MODULE (DM)
The iceMASTER Debug Module is a PC based, combination
in-circuit emulation tool and COP8 based OTP/EPROM programming tool developed and marketed by MetaLink Corporation to support the whole COP8 family of products. National is a resale vendor for these products.
See Figure 19 for configuration.
figured from a master model file.
# Processor specific symbolic display of registers and bit
level assignments, configured from master model file.
# Halt/Idle mode notification.
# Programming menu supports full product line of programmable OTP and EPROM COP8 products. Program data
is taken directly from the overlay RAM.
The iceMASTER Debug Module is a moderate cost development tool. It has the capability of in-circuit emulation for a
specific COP8 microcontroller and in addition serves as a
programming tool for COP8 OTP and EPROM product families. Summary of features is as follows:
# Programming of 44 PLCC and 68 PLCC parts requires
external programming adapters.
# Includes wallmount power supply.
# On-board VPP generator from 5V input or connection to
# Real-time in-circuit emulation; full operating voltage
external supply supported. Requires VPP level adjustment per the family programming specification (correct
level is provided on an on-screen pop-down display).
range operation, full DC-10 MHz clock.
# All processor I/O pins can be cabled to an application
development board with package compatible cable to
socket and surface mount assembly.
# On-line HELP customized to specific processor using
# Full 32 kbytes of loadable programming space that over-
# Includes a copy of COP8-DEV-IBMA assembler and link-
master model file.
lays (replaces) the on-chip ROM or EPROM. On-chip
RAM and I/O blocks are used directly or recreated as
necessary.
er SDK.
DM Order Information
# 100 frames of synchronous trace memory. The display
Debug Module Unit
can be HLL source (C source), assembly or mixed. The
most recent history prior to a break is available in the
trace memory.
COP8-DM/840CJ
Cable Adapters
# Configured break points; uses INTR instruction which is
modestly intrusive.
# Software-only supported features are selectable.
# Tool set integrated interactive symbolic debuggerÐsup-
DM-COP8/20D
20 DIP
DM-COP8/28D
28 DIP
Adapters for SO Package
ports both assembler (COFF) and C Compiler (.COD)
SDK linked object formats.
MHW-SOIC16
16 SO
# Instruction by instruction memory/register changes dis-
MHW-SOIC20
20 SO
MHW-SOIC28
28 SO
played when in single step operation.
TL/DD/11208 – 31
FIGURE 19. COP8-DM Environment
http://www.national.com
26
Development Support (Continued)
COP8 C COMPILER
COP8 ASSEMBLER/LINKER SOFTWARE
DEVELOPMENT TOOL KIT
A C Compiler is developed and marketed by Byte Craft Limited. The COP8C compiler is a fully integrated development
tool specifically designed to support the compact embedded configuration of the COP8 family of products.
Features are summarized as follows:
National Semiconductor offers a relocatable COP8 macro
cross assembler, linker, librarian and utility software development tool kit. Features are summarized as follows:
# Basic and Feature Family instruction set by ‘‘device’’
type.
#
#
#
#
#
#
#
# ANSI C with some restrictions and extensions that optimize development for the COP8 embedded application.
Nested macro capability.
Extensive set of assembler directives.
Supported on PC/DOS platform.
Generates National standard COFF output files.
Integrated Linker and Librarian.
# BITS data type extension. Register declaration Ýpragma
with direct bit level definitions.
# C language support for interrupt routines.
# Expert system, rule based code generation and optimization.
Integrated utilities to generate ROM code file outputs.
DUMPCOFF utility.
This product is integrated as a part of MetaLink tools as a
development kit, fully supported by the MetaLink debugger.
It may be ordered separately or it is bundled with the MetaLink products at no additional cost.
# Performs consistency checks against the architectural
definitions of the target COP8 device.
# Generates program memory code.
# Supports linking of compiled object or COP8 assembled
object formats.
# Global optimization of linked code.
# Symbolic debug load format fully source level supported
Order Information
by the MetaLink debugger.
Assembler SDK
COP8-DEV-IBMA
Assembler SDK on installable
3.5× PC/DOS Floppy Disk Drive
format. Periodic upgrades and
most recent version is available
on National’s BBS and Internet.
Approved List
Manufacturer
North
America
Europe
Asia
BP
Microsystems
(800) 225-2102
(713) 688-4600
Fax: (713) 688-0920
a 49-8152-4183
a 49-8856-932616
a 852-234-16611
a 852-2710-8121
Data I/O
(800) 426-1045
(206) 881-6444
Fax: (206) 882-1043
a 44-0734-440011
Call
North America
HI–LO
(510) 623-8860
Call Asia
a 886-2-764-0215
Fax: a 886-2-756-6403
ICE
Technology
(800) 624-8949
(919) 430-7915
a 44-1226-767404
Fax: 0-1226-370-434
MetaLink
(800) 638-2423
(602) 926-0797
Fax: (602) 693-0681
a 49-80 9156 96-0
Fax: a 49-80 9123 86
a 852-737-1800
Systems
General
(408) 263-6667
a 41-1-9450300
a 886-2-917-3005
Fax: a 886-2-911-1283
Needhams
(916) 924-8037
Fax: (916) 924-8065
27
http://www.national.com
Development Support (Continued)
SINGLE CHIP OTP/EMULATOR SUPPORT
DIAL-A-HELPER BBS via a Standard Modem
The COP8 family is supported by single chip OTP emulators. For detailed information refer to the emulator specific
datasheet and the emulator selection table below:
Modem: CANADA/U.S.: (800) NSC-MICRO
(800) 672-6427
EUROPE:
Baud:
Set-up:
OTP Emulator Ordering Information
Device Number
Clock
Option
Package
Emulates
COP87L22CJN-1N
COP87L22CJN-2N
COP87L22CJN-3N
Crystal
External
R/C
20 DIP
20 DIP
20 DIP
COP822CJ
COP822CJ
COP822CJ
COP87L22CJM-1N
COP87L22CJM-2N
COP87L22CJM-3N
Crystal
External
R/C
20 SO
20 SO
20 SO
COP822CJ
COP822CJ
COP822CJ
COP87L20CJN-1N
COP87L20CJN-2N
COP87L20CJN-3N
Crystal
External
R/C
28 DIP
28 DIP
28 DIP
COP820CJ
COP820CJ
COP820CJ
COP87L20CJM-1N
COP87L20CJM-2N
COP87L20CJM-3N
Crystal
External
R/C
28 SO
28 SO
28 SO
COP820CJ
COP820CJ
COP820CJ
Operation:
DIAL-A-HELPER via FTP
ftp nscmicro.nsc.com
user:
anonymous
password: username @ yourhost.site.domain
DIAL-A-HELPER via a WorldWide Web Browser
ftp://nscmicro.nsc.com
National Semiconductor on the WorldWide Web
See us on the WorldWide Web at: http://www.national.com
CUSTOMER RESPONSE CENTER
Complete product information and technical support is available from National’s customer response centers.
INDUSTRY WIDE OTP/EPROM PROGRAMMING
SUPPORT
Programming support, in addition to the MetaLink development tools, is provided by a full range of independent approved vendors to meet the needs from the engineering
laboratory to full production.
CANADA/U.S.: Tel:
EUROPE:
AVAILABLE LITERATURE
For more information, please see the COP8 Basic Family
User’s Manual, Literature Number 620895, COP8 Feature
Family User’s Manual, Literature Number 620897 and National’s Family of 8-bit Microcontrollers COP8 Selection
Guide, Literature Number 630009.
DIAL-A-HELPER SERVICE
Dial-A-Helper is a service provided by the Microcontroller
Applications group. The Dial-A-Helper is an Electronic Information System that may be accessed as a Bulletin Board
System (BBS) via data modem, as an FTP site on the Internet via standard FTP client application or as an FTP site on
the Internet using a standard Internet browser such as Netscape or Mosaic.
The Dial-A-Helper system provides access to an automated
information storage and retrieval system. The system capabilities include a MESSAGE SECTION (electronic mail,
when accessed as a BBS) for communications to and from
the Microcontroller Applications Group and a FILE SECTION which consists of several file areas where valuable
application software and utilities could be found.
http://www.national.com
( a 49) 0-8141-351332
14.4k
Length: 8-Bit
Parity:
None
Stop Bit: 1
24 Hours, 7 Days
(800) 272-9959
email:
support
@ tevm2.nsc.com
email:
europe.support @ nsc.com
Deutsch Tel:
a 49 (0) 180-530 85 85
English Tel:
a 49 (0) 180-532 78 32
Fran3ais Tel:
a 49 (0) 180-532 93 58
Italiano Tel:
a 49 (0) 180-534 16 80
JAPAN:
Tel:
a 81-043-299-2309
S.E. ASIA:
Beijing Tel:
( a 86) 10-6856-8601
Shanghai Tel:
( a 86) 21-6415-4092
Hong Kong Tel: ( a 852) 2737-1600
28
Korea Tel:
( a 82) 2-3771-6909
Malaysia Tel:
( a 60-4) 644-9061
Singapore Tel:
( a 65) 255-2226
Taiwan Tel:
a 886-2-521-3288
AUSTRALIA:
Tel:
( a 61) 3-9558-9999
INDIA:
Tel:
( a 91) 80-559-9467
29
http://www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
16-Lead Molded Package S.O. (M)
Order Number COPCJ823-XXX/WM
NS Package Number M16B
20-Lead Surface Mount Package (M)
Order Number COPCJ822-XXX/WM
NS Package Number M20B
http://www.national.com
30
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
28-Lead Molded Package S.O. (M)
Order Number COPCJ820-XXX/WM
NS Package Number M28B
20-Lead Molded Dual-In-Line Package (N)
Order Number COPCJ822-XXX/N
NS Package Number N20A
31
http://www.national.com
COP820CJ/COP822CJ/COP823CJ 8-Bit Microcontroller
with Multi-Input Wake Up and Brown Out Detector
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
28-Lead Molded Dual-In-Line Package (N)
Order Number COPCJ820-XXX/N
NS Package Number N28B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
http://www.national.com
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: a49 (0) 180-530 85 86
Email: europe.support @ nsc.com
Deutsch Tel: a49 (0) 180-530 85 85
English Tel: a49 (0) 180-532 78 32
Fran3ais Tel: a49 (0) 180-532 93 58
Italiano Tel: a49 (0) 180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2308
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages