Coilcraft CP-N0530 Outgassing compliant current sensor Datasheet

CURRENT SENSORS
Outgassing Compliant Current Sensors CP-N0530
• For use from 50 kHz to nearly 1 MHz
• Two different pinouts to meet the requirements of different
applications.
• Low primary DC resistance
• 500 Vac isolation from secondary to the core
Core material Ferrite
Terminations Tin-lead (63/37) over tin over nickel over phos bronze
(pins 1 – 6); tin-lead over gold over nickel over copper (pins 7 – 8)
Weight 0.4 g
Ambient temperature –55°C to +125°C
Storage temperature Component: –55°C to +125°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging 250/7″ reel Plastic tape: 16 mm wide, 0.35 mm thick,
12 mm pocket spacing, 5.6 mm pocket depth
PCB washing Only pure water or alcohol recommended
DCR max (Ohms)
Turns (N)
Inductance2
Part number (CP-N0530-)1
pri : sec
min (µH)
primary secondary
0201SZ
0202SZ
1 : 20
81
0.0007
0.400
0301SZ
0302SZ
1 : 30
180
0.0007
0.870
0401SZ
0402SZ
1 : 40
320
0.0007
1.14
0501SZ
0502SZ
1 : 50
500
0.0007
1.50
0601SZ
0602SZ
1 : 60
730
0.0007
1.98
0701SZ
0702SZ
1 : 70
980
0.0007
4.75
1001SZ
1002SZ
1 : 100
2000
0.0007
5.50
1251SZ
1252SZ
1 : 125
3000
0.0007
6.50
1. When ordering, please specify the complete part number,
e.g. CP-N0530-0202SZ
2. Inductance measured between secondary pins at 100 kHz, 0.1 Vrms.
3. Primary current of 10 A causes approximately 25°C temperature rise
from 25°C ambient. Higher current causes a greater temperature rise
(see Temperature Rise vs Current curve).
4. Terminating resistance (RT) value is based on 1 Volt output with
10 Amps flowing through the primary. Varying terminating resistance
increases or decreases output Voltage/Ampere according to the following equation: RT (Ohms) = Vout × Nsec / Iin.
5. Maximum volt-time product for the secondary.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Sensed
current3
Iin (A)
10
10
10
10
10
10
10
10
Terminating
resistance RT4
(Ohms)
2.0
3.0
4.0
5.0
6.0
7.0
10.0
12.5
Volt-time
product5
(V-µsec)
16
24
32
41
49
57
81
101
Typical Circuits
CP-N0530-xxx1
I in
8
6
Pri
(1 turn)
Sec
(N turns)
7
4
RT
Vout
RT
Vout
CP-N0530-xxx2
I in
8
1
Pri
(1 turn)
Sec
(N turns)
7
3
Document CP385-1 Revised 06/28/12
®
© Coilcraft, Inc. 2012
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
Fax 847-639-1508
Email [email protected]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.
CURRENT SENSORS
CP-N0530 Outgassing Compliant Current Sensors
Temperature Rise vs Current
Pinouts
CP-N0530-xxx1
CST1
Temperature rise (from 25°C)
80
70
CP-N0530-xxx2
CST2
8
60
7
3
4
3
4
1
6
1
6
50
40
30
20
10
0
0
2
4
6
8
10
12
14
16
18
7
8
Bottom View
Bottom View
20
Current (A rms)
Dimensions
0.235 max
5,97
Dot
indicates
pin 1
0.245 max
6,22
0.209
max
5,3
0.315
max
8,0
0.004 / 0,10
0.320
max
8,13
Suggested Land Pattern
0.118
3,0
0.023 ±0.008
0,6 ±0,2
0.073 ±0.008
1,85 ±0,2
inches
Dimensions are in
mm
0.098
2,5
0.106
2,7
0.079 ±0.008
2,0 ±0,2
0.063
1,6
0.051
1,3
0.051
1,3
Document CP385-2 Revised 06/28/12
®
© Coilcraft, Inc. 2012
0.073
1,85
0.047
1,2
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
Fax 847-639-1508
Email [email protected]
www.coilcraft-cps.com
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specifications subject to change without notice.
Please check our web site for latest information.
Similar pages