Cirrus CS4339 8-pin, 24-bit, 96 khz stereo d/a converter Datasheet

CS4334/5/6/7/8/9
8-Pin, 24-Bit, 96 kHz Stereo D/A Converter
Features
Description
l Complete Stereo DAC System: Interpolation,
The CS4334 family members are complete, stereo digital-to-analog output systems including interpolation, 1-bit
D/A conversion and output analog filtering in an 8-pin
package. The CS4334/5/6/7/8/9 support all major audio
data interface formats, and the individual devices differ
only in the supported interface format.
D/A, Output Analog Filtering
l 24-Bit Conversion
l 96 dB Dynamic Range
l -88 dB THD+N
l Low Clock Jitter Sensitivity
l Single +5 V Power Supply
l Filtered Line Level Outputs
l On-Chip Digital De-emphasis
l Popgaurd® Technology
l Functionally Compatible with CS4330/31/33
The CS4334 family is based on delta-sigma modulation,
where the modulator output controls the reference voltage input to an ultra-linear analog low-pass filter. This
architecture allows for infinite adjustment of sample rate
between 2 kHz and 100 kHz simply by changing the
master clock frequency.
The CS4334 family contains on-chip digital de-emphasis, operates from a single +5V power supply, and
requires minimal support circuitry. These features are
ideal for set-top boxes, DVD players, SVCD players, and
A/V receivers.
ORDERING INFORMATION
See page 23
I
LRCK
SDATA
DEM/SCLK
2
AGND
6
VA
Serial Input
Interface
De-emphasis
Voltage Reference
Interpolator
∆Σ
Modulator
DAC
Analog
Low-Pass
Filter
8
Interpolator
∆Σ
Modulator
DAC
Analog
Low-Pass
Filter
5
7
3
1
AOUTL
AOUTR
4
MCLK
Preliminary Product Information
P.O. Box 17847, Austin, Texas 78760
(512) 445 7222 FAX: (512) 445 7581
http://www.cirrus.com
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
Copyright  Cirrus Logic, Inc. 1999
(All Rights Reserved)
SEP ‘99
DS248PP3
1
CS4334/5/6/7/8/9
TABLE OF CONTENTS
1. CHARACTERISTICS/SPECIFICATIONS ...................................................... 4
ANALOG CHARACTERISTICS................................................................... 4
POWER AND THERMAL CHARACTERISTICS ......................................... 6
DIGITAL CHARACTERISTICS.................................................................... 7
ABSOLUTE MAXIMUM RATINGS .............................................................. 7
RECOMMENDED OPERATING CONDITIONS .......................................... 7
SWITCHING CHARACTERISTICS ............................................................. 8
2. TYPICAL CONNECTION DIAGRAM ........................................................... 10
3. GENERAL DESCRIPTION .......................................................................... 11
3.1 Digital Interpolation Filter ................................................................... 11
3.2 Delta-Sigma Modulator ...................................................................... 11
3.3 Switched-Capacitor DAC ................................................................... 11
3.4 Analog Low-Pass Filter ...................................................................... 11
4. SYSTEM DESIGN ........................................................................................ 12
4.1 Master Clock ...................................................................................... 12
4.2 Serial Clock ........................................................................................ 12
4.2.1 External Serial Clock Mode ...................................................... 12
4.2.2 Internal Serial Clock Mode ....................................................... 12
4.3 De-Emphasis ..................................................................................... 12
4.4 Initialization and Power-Down ........................................................... 12
4.5 Output Transient Control ................................................................... 13
4.6 Grounding and Power Supply Decoupling ......................................... 13
4.7 Analog Output and Filtering ............................................................... 13
4.8 Overall Base-Rate Frequency Response .......................................... 17
4.9 Overall High-Rate Frequency Response ........................................... 18
4.10 Base Rate Mode Performance Plots ............................................... 19
4.11 High Rate Mode Performance Plots ................................................ 20
5. PIN DESCRIPTIONS ................................................................................... 21
6. PARAMETER DEFINITIONS ....................................................................... 22
7. REFERENCES ............................................................................................. 22
8. ORDERING INFORMATION: ...................................................................... 23
9. FUNCTIONAL COMPATIBILITY ................................................................. 23
10. PACKAGE DIMENSIONS .......................................................................... 24
Contacting Cirrus Logic Support
For a complete listing of Direct Sales, Distributor, and Sales Representative contacts, visit the Cirrus Logic web site at:
http://www.cirrus.com/corporate/contacts/
Preliminary product information describes products which are in production, but for which full characterization data is not yet available. Advance product information describes products which are in development and subject to development changes. Cirrus Logic, Inc. has made best efforts to ensure that the information
contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of
any kind (express or implied). No responsibility is assumed by Cirrus Logic, Inc. for the use of this information, nor for infringements of patents or other rights
of third parties. This document is the property of Cirrus Logic, Inc. and implies no license under patents, copyrights, trademarks, or trade secrets. No part of
this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or
otherwise) without the prior written consent of Cirrus Logic, Inc. Items from any Cirrus Logic website or disk may be printed for use by the user. However, no
part of the printout or electronic files may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical,
photographic, or otherwise) without the prior written consent of Cirrus Logic, Inc.Furthermore, no part of this publication may be used as a basis for manufacture
or sale of any items without the prior written consent of Cirrus Logic, Inc. The names of products of Cirrus Logic, Inc. or other vendors and suppliers appearing
in this document may be trademarks or service marks of their respective owners which may be registered in some jurisdictions. A list of Cirrus Logic, Inc. trademarks and service marks can be found at http://www.cirrus.com.
2
DS248PP3
CS4334/5/6/7/8/9
LIST OF FIGURES
Figure 1.Output Test Load .................................................................................... 6
Figure 2.Maximum Loading................................................................................... 6
Figure 3.Power vs. Sample Rate .......................................................................... 6
Figure 4.External Serial Mode Input Timing.......................................................... 9
Figure 5.Internal Serial Mode Input Timing ........................................................... 9
Figure 6. Internal Serial Clock Generation ............................................................ 9
Figure 7.Recommended Connection Diagram.................................................... 10
Figure 8.System Block Diagram.......................................................................... 11
Figure 9.De-Emphasis Curve (Fs = 44.1kHz) ..................................................... 13
Figure 10.CS4334 Data Format (I2S).................................................................. 14
Figure 11.CS4335 Data Format .......................................................................... 14
Figure 12.CS4336 Data Format .......................................................................... 14
Figure 13.CS4337 Data Format .......................................................................... 15
Figure 14.CS4338 Data Format .......................................................................... 15
Figure 15.CS4339 Data Format .......................................................................... 15
Figure 16.CS4334/5/6/7/8/9 Initialization and Power-Down Sequence .............. 16
Figure 17.Stopband Rejection............................................................................. 17
Figure 18.Transition Band................................................................................... 17
Figure 19.Transition Band................................................................................... 17
Figure 20.Passband Ripple................................................................................. 17
Figure 21.Stopband Rejection............................................................................. 18
Figure 22.Transition Band................................................................................... 18
Figure 23.Transition Band................................................................................... 18
Figure 24.Passband Ripple................................................................................. 18
Figure 25.0 dBFS FFT (BRM) ............................................................................. 19
Figure 26. -60 dBFS FFT (BRM)......................................................................... 19
Figure 27.Idle Channel Noise FFT (BRM)........................................................... 19
Figure 28.Twin Tone IMD FFT (BRM)................................................................. 19
Figure 29.THD+N vs. Amplitude (BRM) .............................................................. 19
Figure 30.THD+N vs. Frequency (BRM) ............................................................. 19
Figure 31.0 dBFS FFT (HRM)............................................................................. 20
Figure 32. -60 dBFS FFT (HRM)......................................................................... 20
Figure 33.Idle Channel Noise FFT (HRM) .......................................................... 20
Figure 34.Twin Tone IMD FFT (HRM) ................................................................ 20
Figure 35.THD+N vs. Amplitude (HRM).............................................................. 20
Figure 36. THD+N vs. Frequency (HRM)............................................................ 20
DS248PP3
3
CS4334/5/6/7/8/9
1. CHARACTERISTICS/SPECIFICATIONS
ANALOG CHARACTERISTICS (TA = 25 °C; Logic "1" = VA = 5 V; Logic "0" = AGND;
Full-Scale Output Sine Wave, 997 Hz; MCLK = 12.288 MHz; Fs for Base-rate Mode = 48 kHz, SCLK = 3.072 MHz,
Measurement Bandwidth 10 Hz to 20 kHz, unless otherwise specified; Fs for High-Rate Mode = 96 kHz,
SCLK = 6.144 MHz, Measurement Bandwidth 10 Hz to 40 kHz, unless otherwise specified. Test load RL = 10 kΩ,
CL = 10 pF (see Figure 1))
Base-rate Mode
Parameter
Symbol
Dynamic Performance for CS4334/5/6/7/8/9-KS
Specified Temperature Range
TA
Dynamic Range
(Note 1)
18 to 24-Bit
unweighted
A-Weighted
16-Bit
unweighted
A-Weighted
Total Harmonic Distortion + Noise
(Note 1) THD+N
18 to 24-Bit
0 dB
-20 dB
-60 dB
16-Bit
0 dB
-20 dB
-60 dB
Interchannel Isolation
(1 kHz)
Dynamic Performance for CS4334/5/6/7/8/9-BS
Specified Temperature Range
TA
Dynamic Range
(Note 1)
18 to 24-Bit
unweighted
A-Weighted
16-Bit
unweighted
A-Weighted
Total Harmonic Distortion + Noise
(Note 1) THD+N
18 to 24-Bit
0 dB
-20 dB
-60 dB
16-Bit
0 dB
-20 dB
-60 dB
Interchannel Isolation
(1 kHz)
High-Rate Mode
Min
Typ
Max
Min
Typ
Max
Unit
-10
-
70
-10
-
70
°C
88
91
86
89
93
96
91
94
-
91
89
90
96
88
94
-
dB
dB
dB
dB
-
-88
-73
-33
-86
-71
-31
-83
-68
-28
-81
-66
-26
-
-88
-70
-30
-86
-68
-28
-83
-65
-25
-81
-63
-23
dB
dB
dB
dB
dB
dB
-
94
-
-
95
-
dB
-40
-
85
-40
-
85
°C
85
88
83
86
93
96
91
94
-
88
86
90
96
88
94
-
dB
dB
dB
dB
-
-88
-73
-33
-86
-71
-31
-82
-65
-25
-70
-63
-23
-
-88
-70
-30
-86
-68
-28
-82
-62
-22
-80
-60
-20
dB
dB
dB
dB
dB
dB
-
94
-
-
95
-
dB
Notes: 1. One-half LSB of triangular PDF dither added to data.
4
DS248PP3
CS4334/5/6/7/8/9
ANALOG CHARACTERISTICS (Continued)
Base-rate Mode
Parameter
Symbol
Min
Typ
Max
High-Rate Mode
Min
Typ
Max Unit
Combined Digital and On-chip Analog Filter Response (Note 2)
(Note 3)
to -0.05 dB corner
0
.4780
to -0.1 dB corner
0
.4650
to -3 dB corner
0
.4996
0
.4982
Frequency Response 10 Hz to 20 kHz
-.01
+.08
-.05
+.2
Passband Ripple
±.08
±.2
StopBand
.5465
.5770
StopBand Attenuation
(Note 4)
50
55
Group Delay
tgd
9/Fs
4/Fs
Passband Group Delay Deviation 0 - 40 kHz
±0.36/Fs
±1.39/Fs
0 - 20 kHz
±0.23/Fs
+1.5/+0
De-emphasis Error
Fs = 32 kHz
+.05/-.25
(Note 5)
Fs = 44.1 kHz
-.2/-.4
Fs = 48 kHz
Passband
Parameters
dc Accuracy
Interchannel Gain Mismatch
Gain Error
Gain Drift
Analog Output
Full Scale Output Voltage
Quiescent Voltage
Max AC-Load Resistance
Max Load Capacitance
Symbol
(Note 6)
(Note 6)
VQ
RL
CL
Fs
Fs
Fs
dB
dB
Fs
dB
s
s
s
dB
dB
dB
Min
Typ
Max
Units
-
0.1
±5
100
0.4
-
dB
%
ppm/°C
3.25
-
3.5
2.2
3
100
3.75
-
Vpp
VDC
kΩ
pF
Notes: 2. Filter response is not tested but is guaranteed by design.
3. Response is clock dependent and will scale with Fs. Note that the response plots (Figures 17-24) have
been normalized to Fs and can be de-normalized by multiplying the X-axis scale by Fs.
4. For Base-Rate Mode, the Measurement Bandwidth is 0.5465 Fs to 3 Fs.
For High-Rate Mode, the Measurement Bandwidth is 0.577 Fs to 1.4 Fs.
5. De-emphasis is not available in High-Rate Mode.
6. Refer to Figure 2.
DS248PP3
5
CS4334/5/6/7/8/9
POWER AND THERMAL CHARACTERISTICS
Parameters
Power Supplies
Power Supply Current
normal operation
power-down state
(Note 7)
normal operation
power-down
Power Dissipation
Package Thermal Resistance
Power Supply Rejection Ratio
(1 kHz)
Symbol
Min
Typ
Max
Units
IA
IA
-
15
40
19
-
mA
µA
θJA
PSRR
-
75
0.2
110
79
104
-
mW
mW
°C/Watt
dB
Notes: 7. Refer to Figure 3. Max Power Dissipation is measured at VA=5.5V.
10 µF
V
out
AOUTx
R
C
L
L
AGND
100
70
75
Safe Operating
Region
50
25
2.5
3
65
HR
M
60
55
5
10
15
Resistive Load -- RL (kΩ)
Figure 2. Maximum Loading
6
M
75
BR
125
Power (mW)
Capacitive Load -- C L (pF)
Figure 1. Output Test Load
20
50
30
40
50
60
70
80
Sample Rate (kHz)
90
100
Figure 3. Power vs. Sample Rate
DS248PP3
CS4334/5/6/7/8/9
DIGITAL CHARACTERISTICS (TA = 25°C; VA = 4.75V - 5.5V)
Parameters
High-Level Input Voltage
Low-Level Input Voltage
Input Leakage Current
Input Capacitance
(Note 8)
Symbol
VIH
VIL
Iin
Min
2.0
-
Typ
8
Max
0.8
±10
-
Units
V
V
µA
pF
Notes: 8. Iin for CS433X LRCK is ±20µA max.
ABSOLUTE MAXIMUM RATINGS (AGND = 0V; all voltages with respect to ground.)
Parameters
DC Power Supply
Input Current, Any Pin Except Supplies
Digital Input Voltage
Ambient Operating Temperature (power applied)
Storage Temperature
Symbol
VA
Iin
VIND
TA
Tstg
Min
-0.3
-0.3
-55
-65
Max
6.0
±10
VA+0.4
125
150
Units
V
mA
V
°C
°C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is
not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS (AGND = 0V; all voltages with respect to ground.)
Parameters
DC Power Supply
DS248PP3
Symbol
VA
Min
4.75
Typ
5.0
Max
5.5
Units
V
7
CS4334/5/6/7/8/9
SWITCHING CHARACTERISTICS (TA = -40 to 85°C; VA = 4.75V - 5.5V; Inputs: Logic 0 = 0V,
Logic 1 = VA, CL = 20pF)
Parameters
Symbol
Input Sample Rate
Fs
Min
Typ
Max
Units
2
-
100
kHz
MCLK Pulse Width High
MCLK/LRCK = 512
10
-
1000
ns
MCLK Pulse Width Low
MCLK/LRCK = 512
10
-
1000
ns
MCLK Pulse Width High MCLK / LRCK = 384 or 192
21
-
1000
ns
MCLK Pulse Width Low
MCLK / LRCK = 384 or 192
21
-
1000
ns
MCLK Pulse Width High MCLK / LRCK = 256 or 128
31
-
1000
ns
MCLK Pulse Width Low
31
-
1000
ns
MCLK / LRCK = 256 or 128
External SCLK Mode
LRCK Duty Cycle (External SCLK only)
SCLK Pulse Width Low
SCLK Pulse Width High
SCLK Period
MCLK / LRCK = 512, 256 or 384
SCLK Period
40
50
60
%
tsclkl
20
-
-
ns
tsclkh
20
-
-
ns
tsclkw
1
---------------------( 128 )Fs
-
-
ns
tsclkw
1
------------------( 64 )Fs
-
-
ns
SCLK rising to LRCK edge delay
tslrd
20
-
-
ns
SCLK rising to LRCK edge setup time
tslrs
20
-
-
ns
SDATA valid to SCLK rising setup time
tsdlrs
20
-
-
ns
SCLK rising to SDATA hold time
Internal SCLK Mode
LRCK Duty Cycle (Internal SCLK only)
SCLK Period
tsdh
20
-
-
ns
-
50
-
%
-
-
ns
-
µs
-
-
ns
-
-
ns
-
-
ns
MCLK / LRCK = 128 or 192
(Note 9)
(Note 10)
tsclkw
SCLK rising to LRCK edge
tsclkr
SDATA valid to SCLK rising setup time
tsdlrs
SCLK rising to SDATA hold time
MCLK / LRCK = 512, 256 or 128
tsdh
SCLK rising to SDATA hold time
MCLK / LRCK = 384 or 192
tsdh
1
----------------SCLK
1
---------------------- + 10
( 512 )Fs
1
---------------------- + 15
( 512 )Fs
1
---------------------- + 15
( 384 )Fs
tsclkw
-----------------2
Notes: 9. In Internal SCLK Mode, the Duty Cycle must be 50% +/− 1/2 MCLK Period.
10. The SCLK / LRCK ratio may be either 32, 48, or 64. This ratio depends on part type and MCLK/LRCK
ratio. (See figures 10-15)
8
DS248PP3
CS4334/5/6/7/8/9
LRCK
t sclkh
t slrs
t slrd
t sclkl
SCLK
t sdh
t sdlrs
SDATA
Figure 4. External Serial Mode Input Timing
LRCK
t sclkr
SDATA
t sclkw
t sdlrs
t sdh
*INTERNAL SCLK
Figure 5. Internal Serial Mode Input Timing
* The SCLK pulses shown are internal to the CS4334/5/6/7/8/9.
LRCK
MCLK
1
N
2
N
*INTERNAL SCLK
SDATA
Figure 6. Internal Serial Clock Generation
* The SCLK pulses shown are internal to the CS4334/5/6/7/8/9.
N equals MCLK divided by SCLK
DS248PP3
9
CS4334/5/6/7/8/9
2. TYPICAL CONNECTION DIAGRAM
+5V
+
7
0.1 µF
1 µF
VA
1
Audio
Data
Processor
2
3
SDATA
8
DEM/SCLK
AOUTL
LRCK
3.3 µF
560 Ω
Left Audio
Output
+
267 k
C
10 kΩ
RL
CS4334
CS4335
CS4336
CS4337
CS4338
CS4339
3.3 µF
AOUTR
External Clock
4
MCLK
5
560 Ω
Right Audio
Output
+
267 k
C
10 kΩ
AGND
C=
RL
R L + 560
4πFs(R L560)
6
Figure 7. Recommended Connection Diagram
10
DS248PP3
CS4334/5/6/7/8/9
3. GENERAL DESCRIPTION
The CS4334 family of devices offers a complete
stereo digital-to-analog system including digital interpolation, fourth-order delta-sigma digital-to-analog conversion, digital de-emphasis and analog
filtering, as shown in Figure 8. This architecture
provides a high tolerance to clock jitter.
The primary purpose of using delta-sigma modulation techniques is to avoid the limitations of resistive laser trimmed digital-to-analog converter
architectures by using an inherently linear 1-bit
digital-to-analog converter. The advantages of a 1bit digital-to-analog converter include: ideal differential linearity, no distortion mechanisms due to resistor matching errors and no linearity drift over
time and temperature due to variations in resistor
values.
filter eliminates images of the baseband audio signal which exist at multiples of the input sample
rate. The resulting frequency spectrum has images
of the input signal at multiples of 4 Fs. These images are easily removed by the on-chip analog lowpass filter and a simple external analog filter (see
Figure 7).
3.2 Delta-Sigma Modulator
The interpolation filter is followed by a fourth order delta-sigma modulator which converts the interpolation filter output into 1-bit data at a rate of
128 Fs in BRM (or 64 Fs in HRM).
3.3 Switched-Capacitor DAC
The CS4334 family of devices supports two modes
of operation. The devices operate in Base Rate
Mode (BRM) when MCLK/LRCK is 256, 384 or
512 and in High Rate Mode (HRM) when
MCLK/LRCK is 128 or 192. High Rate Mode allows input sample rates up to 100 kHz.
The delta-sigma modulator is followed by a digitalto-analog converter which translates the 1-bit data
into a series of charge packets. The magnitude of
the charge in each packet is determined by sampling of a voltage reference onto a switched capacitor, where the polarity of each packet is controlled
by the 1-bit data. This technique greatly reduces the
sensitivity to clock jitter and provides low-pass filtering of the output.
3.1 Digital Interpolation Filter
3.4 Analog Low-Pass Filter
The digital interpolation filter increases the sample
rate, Fs, by a factor of 4 and is followed by a
32× digital sample-and-hold (16× in HRM). This
The final signal stage consists of a continuous-time
low-pass filter which serves to smooth the output
and attenuate out-of-band noise.
Digital
Input
Interpolator
Delta-Sigma
Modulator
DAC
Analog
Low-Pass
Filter
Analog
Output
Figure 8. System Block Diagram
DS248PP3
11
CS4334/5/6/7/8/9
4. SYSTEM DESIGN
4.2.1 External Serial Clock Mode
The CS4334 family accepts data at standard audio
sample rates including 48, 44.1 and 32 kHz in
BRM and 96, 88.2 and 64 kHz in HRM. Audio data
is input via the serial data input pin (SDATA). The
Left/Right Clock (LRCK) defines the channel and
delineation of data, and the Serial Clock (SCLK)
clocks audio data into the input data buffer. The
CS4334/5/6/7/8/9 differ in serial data formats as
shown in Figures 10-15.
The CS4334 family will enter the External Serial
4.1 Master Clock
MCLK must be either 256x, 384x or 512x the desired input sample rate in BRM and either 128x or
192x the desired input sample rate in HRM. The
LRCK frequency is equal to Fs, the frequency at
which words for each channel are input to the device. The MCLK-to-LRCK frequency ratio is detected automatically during the initialization
sequence by counting the number of MCLK transitions during a single LRCK period. Internal dividers are set to generate the proper clocks. Table 1
illustrates several standard audio sample rates and
the required MCLK and LRCK frequencies. Please
note there is no required phase relationship, but
MCLK, LRCK and SCLK must be synchronous.
LRCK
(kHz)
32
44.1
48
64
88.2
96
MCLK (MHz)
HRM
BRM
128x
192x
256x
384x
512x
4.0960 6.1440 8.1920 12.2880 16.3840
5.6448 8.4672 11.2896 16.9344 22.5792
6.1440 9.2160 12.2880 18.4320 24.5760
8.1920 12.2880
11.2896 16.9344
12.2880 18.4320
Table 1. Common Clock Frequencies
4.2 Serial Clock
The serial clock controls the shifting of data into
the input data buffers. The CS4334 family supports
both external and internal serial clock generation
modes. Refer to Figures 10-15 for data formats.
12
Clock Mode when 16 low to high transitions are
detected on the DEM/SCLK pin during any phase
of the LRCK period. When this mode is enabled,
the Internal Serial Clock Mode and de-emphasis
filter cannot be accessed. The CS4334 family will
switch to Internal Serial Clock Mode if no low to
high transitions are detected on the DEM/SCLK
pin for 2 consecutive frames of LRCK. Refer to
Figure 16.
4.2.2 Internal Serial Clock Mode
In the Internal Serial Clock Mode, the serial clock
is internally derived and synchronous with MCLK
and LRCK. The SCLK/LRCK frequency ratio is either 32, 48, or 64 depending upon data format. Operation in this mode is identical to operation with
an external serial clock synchronized with LRCK.
This mode allows access to the digital de-emphasis
function. Refer to Figures 10 - 16 for details.
While the Internal Serial Clock Mode is provided
to allow access to the de-emphasis filter, the Internal Serial Clock Mode also eliminates possible
clock interference from an external SCLK.
4.3 De-Emphasis
The CS4334 family includes on-chip digital de-emphasis. Figure 9 shows the de-emphasis curve for
Fs equal to 44.1 kHz. The frequency response of
the de-emphasis curve will scale proportionally
with changes in sample rate, Fs.
The de-emphasis filter is active (inactive) if the
DEM/SCLK pin is low (high) for 5 consecutive
falling edges of LRCK. This function is available
only in the internal serial clock mode.
4.4 Initialization and Power-Down
The Initialization and Power-Down sequence flow
chart is shown in Figure 16. The CS4334 family enters the Power-Down State upon initial power-up.
DS248PP3
CS4334/5/6/7/8/9
capacitor to charge to VQ, effectively blocking the
quiescent DC voltage.
Gain
dB
T1=50 µs
0dB
T2 = 15 µs
-10dB
F1
3.183 kHz
F2
Frequency
10.61 kHz
Figure 9. De-Emphasis Curve (Fs = 44.1kHz)
The interpolation filters and delta-sigma modulators are reset, and the internal voltage reference,
one-bit digital-to-analog converters and switchedcapacitor low-pass filters are powered down. The
device will remain in the Power-Down mode until
MCLK and LRCK are present. Once MCLK and
LRCK are detected, MCLK occurrences are counted over one LRCK period to determine the
MCLK/LRCK frequency ratio. Power is then applied to the internal voltage reference. Finally, power is applied to the D/A converters and switchedcapacitor filters, and the analog outputs will ramp to
the quiescent voltage, VQ.
4.5 Output Transient Control
The CS4334 family uses Popgaurd® technology to
minimize the effects of output transients during
power-up and power-down. This technique eliminates the audio transients commonly produced by
single-ended single-supply converters when it is
implemented with external DC-blocking capacitors
connected in series with the audio outputs. To
make best use of this feature, it is necessary to understand its operation.
When the device is initially powered-up, the audio
outputs, AOUTL and AOUTR, are clamped to
AGND. After a short delay of approximately 1000
sample periods, each output begins to ramp towards its quiescent voltage, VQ. Approximately
10,000 sample cycles later, the outputs reach VQ
and audio output begins. This gradual voltage
ramping allows time for the external DC-blocking
DS248PP3
To prevent transients at power-down, the device
must first enter its power-down state. This is accomplished by removing MCLK or LRCK. When
this occurs, audio output ceases and the internal
output buffers are disconnected from AOUTL and
AOUTR. A soft-start current sink is substituted in
place of AOUTL and AOUTR which allows the
DC-blocking capacitors to slowly discharge. Once
this charge is dissipated, the power to the device
may be turned off, and the system is ready for the
next power-on.
To prevent an audio transient at the next power-on,
the DC-blocking capacitors must fully discharge
before turning off the power or exiting the powerdown state. If full discharge does not occur, a transient will occur when the audio outputs are initially
clamped to AGND. The time that the device must
remain in the power-down state is related to the
value of the DC-blocking capacitance. For example, with a 3.3 µF capacitor, the time that the device
must remain in the power-down state will be approximately 0.4 seconds.
4.6 Grounding and Power Supply
Decoupling
As with any high resolution converter, the CS4334
family requires careful attention to power supply
and grounding arrangements to optimize performance. Figure 7 shows the recommended power arrangement with VA connected to a clean +5V
supply. For best performance, decoupling capacitors should be located as close to the device package as possible with the smallest capacitor closest.
4.7 Analog Output and Filtering
The analog filter present in the CS4334 family is a
switched-capacitor filter followed by a continuous
time low pass filter. Its response, combined with
that of the digital interpolator, is given in Figures
17 - 24.
13
CS4334/5/6/7/8/9
Left Channel
LRCK
Right Channel
SCLK
SDATA
MSB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
MSB -1 -2 -3 -4
Internal SCLK Mode
+5 +4 +3 +2 +1 LSB
External SCLK Mode
I2
I2
S, 16-Bit data and INT SCLK = 32 Fs if
MCLK/LRCK = 512, 256 or 128
I2S, Up to 24-Bit data and INT SCLK = 48 Fs if
MCLK/LRCK = 384 or 192
S, up to 24-Bit Data
Data Valid on Rising Edge of SCLK
Figure 10. CS4334 Data Format (I2S)
Left Channel
LRCK
Right Channel
SCLK
SDATA
MSB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
MSB -1 -2 -3 -4
Internal SCLK Mode
+5 +4 +3 +2 +1 LSB
External SCLK Mode
Left Justified, up to 24-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Left Justified, up to 24-Bit Data
Data Valid on Rising Edge of SCLK
Figure 11. CS4335 Data Format
LRCK
Right Channel
Left Channel
SCLK
SDATA
0
23 22 21 20 19 18
7
6
5
4
3
2
1
0
23 22 21 20 19 18
7
6
5
4
3
2
1
0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 24-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 24-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 48 Cycles per LRCK Period
Figure 12. CS4336 Data Format
14
DS248PP3
CS4334/5/6/7/8/9
LRCK
Right Channel
Left Channel
SCLK
SDATA
1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 20-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 20-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 40 Cycles per LRCK Period
Figure 13. CS4337 Data Format
LRCK
Right Channel
Left Channel
SCLK
SDATA
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 16-Bit Data
INT SCLK = 32 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 16-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 32 Cycles per LRCK Period
Figure 14. CS4338 Data Format
LRCK
Right Channel
Left Channel
SCLK
SDATA
1 0
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 18-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 18-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 36 Cycles per LRCK Period
Figure 15. CS4339 Data Format
DS248PP3
15
CS4334/5/6/7/8/9
Figure 16. CS4334/5/6/7/8/9 Initialization and Power-Down Sequence
16
DS248PP3
CS4334/5/6/7/8/9
4.8 Overall Base-Rate Frequency Response
Figure 17. Stopband Rejection
Figure 18. Transition Band
0.1
0.08
Amplitude dB
0.06
0.04
0.02
0
0.02
0
Figure 19. Transition Band
DS248PP3
0.05
0.1
0.15
0.2
0.25
0.3
0.35
Frequency (normalized to Fs)
0.4
0.45
Figure 20. Passband Ripple
17
CS4334/5/6/7/8/9
4.9 Overall High-Rate Frequency Response
Figure 21. Stopband Rejection
Figure 22. Transition Band
0.25
0.2
Amplitude dB
0.15
0.1
0.05
0
0.05
0.1
0.15
0
Figure 23. Transition Band
18
0.05
0.1
0.15
0.2
0.25
0.3
0.35
Frequency (normalized to Fs)
0.4
0.45
Figure 24. Passband Ripple
DS248PP3
CS4334/5/6/7/8/9
4.10 Base Rate Mode Performance Plots
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
dBr
A
dBr A
d
B
r
A
-40
-40
-40
-50
-50
-50
-60
-60
-60
dBr
A
dBr A
-40
-40
-40
-50
-50
-50
-60
-60
-60
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
-70
-70
-70
-80
-80
-80
-90
-90
-90
A
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-120
-120
-120
-130
-130
-130
-140
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
20k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
Figure 25. 0 dBFS FFT (BRM)
Figure 26. -60 dBFS FFT (BRM)
18k
18k
18k
20k
20k
20k
18k
20k
20k
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
-40
-40
-40
A
dBr
dBr A
A
dBr
A
dBr A
-50
-50
-50
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
-60
-60
-60
-70
-70
-70
-80
-80
-80
-90
-90
-90
-100
-100
-100
-100
-100
-100
-110
-110
-110
-110
-110
-110
-120
-120
-120
-130
-130
-130
-140
-140
-140
6k
6k
6k
(16k FFT of a 1 kHz input signal)
-40
-40
-40
-50
-50
-50
-60
-60
-60
A
4k
4k
4k
(16k FFT of a 1 kHz input signal)
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
d
B
r
2k
2k
2k
-120
-120
-120
-130
-130
-130
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
20k
20k
20k
-140
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
1 6k
16k
16k
18k
18k
20k
(16k FFT with no input signal)
(16k FFT of intermodulation distortion using 13 kHz and 14 kHz input signals)
Figure 27. Idle Channel Noise FFT (BRM)
Figure 28. Twin Tone IMD FFT (BRM)
-60
-60
+0
+0
+0
-10
-10
-10
-20
-20
-20
-70
-70
-30
-30
-30
A
-90
-90
-40
-40
-40
dBr
dBrAA
dBr A
d
B
r
-80
-80
d
B
r
A
-50
-50
-50
-60
-60
-60
-70
-70
-70
-80
-80
-80
-100
-100
-90
-90
-90
-100
-100
-100
-110
-110
-60
-60
-50
-50
-40
-40
-30
-30
-20
-20
-10
-10
+0
+0
dBFS
dBFS
-110
-110
-110
20
20
20
50
50
50
100
100
100
200
200
200
500
500
500
Hz
Hz
Hz
1k
1k
1k
2k
2k
2k
5k
5k
5k
10k
10k
10k
20k
20k
20k
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
Figure 29. THD+N vs. Amplitude (BRM)
Figure 30. THD+N vs. Frequency (BRM)
All measurements were taken from the CDB4334 evaluation board using the Audio Precision Dual Domain
System Two Cascade.
DS248PP3
19
CS4334/5/6/7/8/9
4.11 High Rate Mode Performance Plots
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
-40
-40
-40
-50
-50
-50
-60
-60
-60
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
dBr
A
dBr A
dBr
A
dBr A
d
B
r
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
A
-40
-40
-40
-50
-50
-50
-60
-60
-60
A
-70
-70
-70
-80
-80
-80
-90
-90
-90
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-120
-120
-120
-130
-130
-130
-140
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
2k
2k
2k
4k
4k
4k
12k
12k
12k
14k
14k
14k
16k
16k
16k
Figure 31. 0 dBFS FFT (HRM)
Figure 32. -60 dBFS FFT (HRM)
D -A C C IF IMD vs A MP L ITUD E
18k
18k
18k
20k
20k
20k
0 8 /0 5 /9 9 1 1 :1 1 :3 6
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
-40
-40
-40
-40
-40
-40
-50
-50
-50
-60
-60
-60
dBr
A
dBr A
A
dBr
A
dBr A
-50
-50
-50
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
-60
-60
-60
-70
-70
-70
-80
-80
-80
-90
-90
-90
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-140
-140
-140
10k
10k
10k
Hz
Hz
Hz
(16k FFT of a 1 kHz input signal)
A ud io P re c is io n
A
8k
8k
8k
(16k FFT of a 1 kHz input signal)
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
d
B
r
6k
6k
6k
-120
-120
-120
-130
-130
-130
2k
2k
4k
4k
4k
2k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
2k
2k
2k
Hz
Hz
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
HzHz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
20k
20k
20k
(16k FFT with no input signal)
(16k FFT of intermodulation distortion using 13 kHz and 14 kHz input signals)
Figure 33. Idle Channel Noise FFT (HRM)
Figure 34. Twin Tone IMD FFT (HRM)
-60
-60
+0
+0
+0
-10
-10
-10
-20
-20
-20
-70
-70
-30
-30
-30
A
-90
-90
d
B
r
-40
-40
-40
dBrdBrAA
-80
-80
dBr A
d
B
r
-50
-50
-50
-60
-60
-60
A
-70
-70
-70
-80
-80
-80
-100
-100
-90
-90
-90
-100
-100
-100
-110
-110
-60
-60
-50
-50
-40
-40
-30
-30
-20
-20
-10
-10
+0
+0
dBFS
dBFS
-110
-110
-110
20
20
20
50
50
100
100
100
200
200
200
500
500
Hz
Hz
Hz
1k
1k
2k
2k
5k
5k
10k
10k
10k
20k
20k
20k
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
Figure 35. THD+N vs. Amplitude (HRM)
Figure 36. THD+N vs. Frequency (HRM)
All measurements were taken from the CDB4334 evaluation board using the Audio Precision Dual Domain
System Two Cascade.
20
DS248PP3
CS4334/5/6/7/8/9
5. PIN DESCRIPTIONS
SERIAL DATA INPUT
SDATA
1
8
AOUTL
ANALOG LEFT CHANNEL OUTPUT
DE-EMPHASIS / SCLK
DEM/SCLK
2
7
VA
ANALOG POWER
LEFT / RIGHT CLOCK
LRCK
3
6
AGND
ANALOG GROUND
MASTER CLOCK
MCLK
4
5
AOUTR
ANALOG RIGHT CHANNEL OUTPUT
No.
1
Pin Name
SDATA
2
DEM/SCLK
3
LRCK
4
MCLK
5
6
7
8
AOUTR
AGND
VA
AOUTL
DS248PP3
I/O
Pin Function and Description
I Serial Audio Data Input - two’s complement MSB-first serial data is input on this pin.
The data is clocked into the CS4334/5/6/7/8/9 via internal or external SCLK, and the
channel is determined by LRCK.
I De-Emphasis/External Serial Clock Input - used for de-emphasis filter control or external serial clock input.
I Left/Right Clock - determines which channel is currently being input on the Audio Serial
Data Input pin, SDATA.
I Master Clock - frequency must be 256x, 384x, or 512x the input sample rate in BRM and
either 128x or 192x the input sample rate in HRM.
O Analog Right Channel Output - typically 3.5 Vp-p for a full-scale input signal.
I Analog Ground - analog ground reference is 0V.
I Analog Power - analog power supply is nominally +5V.
O Analog Left Channel Output - typically 3.5 Vp-p for a full-scale input signal.
21
CS4334/5/6/7/8/9
6. PARAMETER DEFINITIONS
Total Harmonic Distortion + Noise (THD+N)- The ratio of the rms value of the signal to the
rms sum of all other spectral components over the specified bandwidth (typically 10Hz to
20kHz), including distortion components. Expressed in decibels.
Dynamic Range - The ratio of the full scale rms value of the signal to the rms sum of all other
spectral components over the specified bandwidth. Dynamic range is a signal-to-noise
measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is then added
to the resulting measurement to refer the measurement to full scale. This technique ensures that
the distortion components are below the noise level and do not effect the measurement. This
measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and
the Electronic Industries Association of Japan, EIAJ CP-307.
Interchannel Isolation - A measure of crosstalk between the left and right channels. Measured
for each channel at the converter’s output with all zeros to the input under test and a full-scale
signal applied to the other channel. Units in decibels.
Interchannel Gain Mismatch - The gain difference between left and right channels. Units in
decibels.
Gain Error - The deviation from the nominal full scale analog output for a full scale digital
input.
Gain Drift - The change in gain value with temperature. Units in ppm/°C.
7. REFERENCES
1) "How to Achieve Optimum Performance from
Delta-Sigma A/D & D/A Converters" by
Steven Harris. Paper presented at the 93rd Convention of the Audio Engineering Society, October 1992.
2) CDB4334/5/6/7/8/9 Evaluation Board Datasheet
22
DS248PP3
CS4334/5/6/7/8/9
8. ORDERING INFORMATION:
Model
CS4334-KS
CS4335-KS
CS4336-KS
CS4337-KS
CS4338-KS
CS4339-KS
CS4334-BS
CS4335-BS
CS4336-BS
CS4337-BS
CS4338-BS
CS4339-BS
Temperature
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
Package
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
8-pin Plastic SOIC
Serial Interface
16 to 24-bit, I2S
16 to 24-bit, left justified
24-bit, right justified
20-bit, right justified
16-bit, right justified
18-bit, right justified, 32 Fs Internal SCLK mode
16 to 24-bit, I2S
16 to 24-bit, left justified
24-bit, right justified
20-bit, right justified
16-bit, right justified
18-bit, right justified, 32 Fs Internal SCLK mode
9. FUNCTIONAL COMPATIBILITY
CS4330-KS ⇒ CS4339-KS
CS4331-KS ⇒ CS4334-KS
CS4333-KS ⇒ CS4338-KS
CS4330-BS ⇒ CS4339-BS
CS4331-BS ⇒ CS4334-BS
CS4333-BS ⇒ CS4338-BS
DS248PP3
23
CS4334/5/6/7/8/9
10. PACKAGE DIMENSIONS
8L SOIC (150 MIL BODY) PACKAGE DRAWING
E
H
1
b
c
D
SEATING
PLANE
∝
A
L
e
A1
INCHES
DIM
A
A1
B
C
D
E
e
H
L
∝
MIN
0.053
0.004
0.013
0.007
0.189
0.150
0.040
0.228
0.016
0°
MAX
0.069
0.010
0.020
0.010
0.197
0.157
0.060
0.244
0.050
8°
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.02
1.52
5.80
6.20
0.40
1.27
0°
8°
JEDEC # : MS-012
24
DS248PP3
• Notes •
Similar pages