Intersil CS82C86H-5 Cmos octal bus transceiver Datasheet

82C86H
CMOS Octal Bus Transceiver
March 1997
Features
Description
• Full Eight Bit Bi-Directional Bus Interface
The Intersil 82C86H is a high performance CMOS Octal
Transceiver manufactured using a self-aligned silicon gate
CMOS process (Scaled SAJI IV). The 82C86H provides a full
eight-bit bi-directional bus interface in a 20 lead package. The
Transmit (T) control determines the data direction. The active
low output enable (OE) permits simple interface to the 80C86,
80C88 and other microprocessors. The 82C86H has gated
inputs, eliminating the need for pull-up/pull-down resistors and
reducing overall system operating power dissipation.
• Industry Standard 8286 Compatible Pinout
• High Drive Capability
- B Side IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
- A Side IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12mA
• Three-State Outputs
• Propagation Delay . . . . . . . . . . . . . . . . . . . . . 35ns Max.
• Gated Inputs
- Reduce Operating Power
- Eliminate the Need for Pull-Up Resistors
Ordering Information
PART NUMBER
• Single 5V Power Supply
5MHz
• Low Power Operation . . . . . . . . . . . . . . . ICCSB = 10µA
• Operating Temperature Range
- C82C86H . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
- I82C86H . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
- M82C86H . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
CP82C86H-5
IP82C86H-5
CS82C86H-5
IS82C86H-5
8MHz
PACKAGE
CP82C86H 20 Ld
PDIP
IP82C86H
CS82C86H 20 Ld
PLCC
IS82C86H
CD82C86H-5
CD82C86H 20 Ld
CERDIP
ID82C86H-5
ID82C86H
MD82C86H-5/B
-
59628757701RA
-
MR82C86H-5/B
-
596287577012A
-
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
4-317
TEMP. RANGE
0oC to +70oC
-40oC
0oC
to
-40oC
0oC
to
+70oC
to
to
+85oC
+85oC
+70oC
PKG.
NO.
E20.3
E20.3
N20.35
N20.35
F20.3
-40oC to +85oC F20.3
-55oC to
+125oC
SMD #
20 Pad
CLCC
F20.3
F20.3
-55oC to
+125oC
SMD #
J20.A
J20.A
File Number
2977.1
82C86H
Pinouts
A1
A0
VCC
B0
82C86H (PLCC, CLCC)
TOP VIEW
A2
82C86H (PDIP, CERDIP)
TOP VIEW
3
2
1
20
19
TRUTH TABLE
A0 1
20 VCC
A1 2
19 B0
A2 3
18 B1
A3 4
17 B2
A3 4
18 B1
A4 5
16 B3
A4 5
17 B2
A5 6
15 B4
A5 6
16 B3
A6 7
14 B5
A7 8
13 B6
A6 7
15 B4
OE 9
12 B7
A7 8
14 B5
GND 10
11 T
H
L
I
O
X
Hi-Z
T
OE
A
B
X
H
Hi-Z
Hi-Z
H
L
I
O
L
L
O
I
= Logic One
= Logic Zero
= Input Mode
= Output Mode
= Don’t Care
= High Impedance
PIN NAMES
11
12
GND
T
B7
13
B6
10
OE
PIN
9
Local Bus Data I/O Pins
B0-B7
System Bus Data I/O Pins
T
OE
4-318
DESCRIPTION
A0-A7
Transmit Control Input
Active Low Output Enable
82C86H
Functional Diagram
Decoupling Capacitors
B0
The transient current required to charge and discharge the
300pF load capacitance specified in the 82C86H/87H data
sheet is determined by:
A1
B1
I = C L ( dv ⁄ dt )
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A0
(EQ. 1)
Assuming that all outputs change state at the same time and
that dv/dt is constant;
(V CC × 80% )
I = C L ------------------------------------tR ⁄ tF
(EQ. 2)
where tR = 20ns, VCC = 5.0V, CL = 300pF on each eight outputs.
I = ( 80 × 300 × 10
= 480mA
– 12
) × ( 5.0V × 0.8 ) ⁄ ( 20 × 10
–9
)
(EQ. 3)
OE
T
VCC
VCC
P
Gated Inputs
P
N
During normal system operation of a latch, signals on the
bus at the device inputs will become high impedance or
make transitions unrelated to the operation of the latch.
These unrelated input transitions switch the input circuitry
and typically cause an increase in power dissipation in
CMOS devices by creating a low resistance path between
VCC and GND when the signal is at or near the input switching threshold. Additionally, if the driving signal becomes high
impedance (“float” condition), it could create an indeterminate logic state at the inputs and cause a disruption in
device operation.
STB
INTERNAL
DATA
N
N
FIGURE 1. 82C82/83H
VCC
The Intersil 82C8X series of bus drivers eliminates these
conditions by turning off data inputs when data is latched
(STB = logic zero for the 82C82/83H) and when the device is
disabled (OE = logic one for the 82C86H/87H). These gated
inputs disconnect the input circuitry from the VCC and
ground power supply pins by turning off the upper P-channel
and lower N-channel (See Figures 1 and 2). No current flow
from VCC to GND occurs during input transitions and invalid
logic states from floating inputs are not transmitted. The next
stage is held to a valid logic level internal to the device.
D.C. input voltage levels can also cause an increase in ICC if
these input levels approach the minimum VIH or maximum
VIL conditions. This is due to the operation of the input circuitry in its linear operating region (partially conducting
state). The 82C8X series gated inputs mean that this condition will occur only during the time the device is in the transparent mode (STB = logic one). ICC remains below the
maximum ICC standby specification of 10µA during the time
inputs are disabled, thereby greatly reducing the average
power dissipation of the 82C8X series devices.
P
DATA IN
P
OE
P
INTERNAL
DATA
DATA IN
VCC
N
P
N
N
FIGURE 2. 82C86H/87H GATED INPUTS
This current spike may cause a large negative voltage spike
on VCC which could cause improper operation of the device.
To filter out this noise, it is recommended that a 0.1µF
ceramic disc capacitor be placed between VCC and GND at
each device, with placement being as near to the device as
possible.
4-319
82C86H
Absolute Maximum Ratings
Thermal Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage . . . . . . . . . . . . GND -0.5V to VCC +0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance (Typical)
θJA (oC/W) θJC (oC/W)
CERDIP Package . . . . . . . . . . . . . . . .
70
16
CLCC Package . . . . . . . . . . . . . . . . . .
80
20
PDIP Package . . . . . . . . . . . . . . . . . . .
75
N/A
PLCC Package . . . . . . . . . . . . . . . . . .
75
N/A
Maximum Storage Temperature Range . . . . . . . . . -65oC to +150oC
Maximum Junction Temperature Hermetic Package . . . . . . . +175oC
Maximum Junction Temperature Plastic Package. . . . . . . . . +150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300oC
(PLCC - Lead Tips Only)
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range
C82C86H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
I82C86H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
M82C86H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
DC Electrical Specifications
SYMBOL
VIH
VCC = 5.0V ± 10%; TA = 0oC to +70oC (C82C86H);
TA = -40oC to +85oC (I82C86H);
TA = -55oC to +125oC (M82C86H)
PARAMETER
Logical One
Input Voltage
MAX
UNITS
2.0
-
V
C82C86H, I82C86H
V
M82C86H (Note 1)
2.2
VIL
Logical Zero Input Voltage
VOH
Logical One Output Voltage
-
0.8
TEST CONDITIONS
V
B Outputs
3.0
V
IOH = -8mA
A Outputs
3.0
V
IOH = -4mA
VCC -0.4
V
IOH = -100µA
A or B Outputs
VOL
MIN
Logical Zero Output Voltage
B Outputs
0.45
V
IOL = 20mA
A Outputs
0.45
V
IOL = 12mA
II
Input Leakage Current
-10.0
10.0
µA
VIN = GND or VCC DIP Pins 9, 11
IO
Output Leakage Current
-10.0
10.0
µA
VO = GND or VCC, OE ≥ VCC -0.5V
DIP Pins 1 - 8, 12 - 19
VIN = VCC or GND, VCC = 5.5V, Outputs Open
ICCSB
Standby Power Supply
Current
-
10
µA
ICCOP
Operating Power Supply
Current
-
1
mA/MHz
TA = +25oC, Typical (See Note 2)
NOTES:
1. VIH is measured by applying a pulse of magnitude = VIH(MIN) to one data input at a time and checking the corresponding device output for
a valid logical “1” during valid input high time. Control pins (T, OE) are tested separately with all device data input pins at VCC -0.4
2. Typical ICCOP = 1mA/MHz of read/ cycle time. (Example: 1.0µs read/write cycle time = 1mA).
Capacitance
SYMBOL
CIN
TA = +25oC
PARAMETER
TYPICAL
UNITS
B Inputs
18
pF
A Inputs
14
pF
TEST CONDITIONS
Input Capacitance
4-320
Freq = 1MHz, all measurements are
referenced to device GND
82C86H
AC Electrical Specifications
VCC = 5.0V ± 10%;
Freq = 1MHz
TA = 0oC to +70oC (C82C86H);
TA = -40oC to +85oC (I82C86H);
TA = -55oC to +125oC (M82C86H)
NOTE 4
SYMBOL
(1)
PARAMETER
TIVOV
MIN
82C86H
MAX
82C86H-5
MAX
UNITS
Input to Output Delay
TEST CONDITIONS
Notes 1, 2
Inverting
5
30
35
ns
Non-Inverting
5
32
35
ns
(2)
TEHTV
Transmit/Receive Hold Time
5
-
-
ns
Notes 1, 2
(3)
TTVEL
Transmit/Receive Setup Time
10
-
-
ns
Notes 1, 2
(4)
TEHOZ
Output Disable Time
5
30
35
ns
Notes 1, 2
(5)
TELOV
Output Enable Time
10
50
65
ns
Notes 1, 2
(6)
TR, TF
Input Rise/Fall Times
-
20
20
ns
Notes 1, 2
(7)
TEHEL
Minimum Output Enable High Time
Note 3
82C86H
30
-
-
ns
82C86H-5
35
-
-
ns
NOTES:
1. All AC parameters tested as per test circuits and definitions in timing waveforms and test load circuits. Input rise and fall times are driven
at 1ns/V.
2. Input test signals must switch between VIL - 0.4V and VIH +0.4V.
3. A system limitation only when changing direction. Not a measured parameter.
4. 82C86H is available in commercial and industrial temperature ranges only. 82C86H-5 is available in commercial, industrial and military
temperature ranges.
Timing Waveform
TR, TF (6)
INPUTS
2.0V
0.8V
TEHEL (7)
OE
(4)
TEHOZ
(1)
TIVOV
TELOV (5)
VOH -0.1V
OUTPUTS
VOL +0.1V
TEHTV (2)
T
NOTE: All timing measurements are made at 1.5V unless otherwise noted.
4-321
3.0V
0.45V
TTVEL (3)
82C86H
Test Load Circuits
A SIDE OUTPUTS
TIVOV LOAD CIRCUIT
TELOV OUTPUT HIGH
ENABLE LOAD CIRCUIT
TELOV OUTPUT LOW
ENABLE LOAD CIRCUIT
1.5V
1.5V
2.36V
160Ω
375Ω
TEST
POINT
OUTPUT
100pF
(SEE NOTE)
2.36V
91Ω
TEST
POINT
OUTPUT
TEHOZ OUTPUT LOW/HIGH
DISABLE LOAD CIRCUIT
TEST
POINT
OUTPUT
100pF
(SEE NOTE)
160Ω
TEST
POINT
OUTPUT
100pF
(SEE NOTE)
50pF
(SEE NOTE)
B SIDE OUTPUTS
TIVOV LOAD CIRCUIT
TELOV OUTPUT HIGH
ENABLE LOAD CIRCUIT
TELOV OUTPUT LOW
ENABLE LOAD CIRCUIT
1.5V
1.5V
2.27V
91Ω
OUTPUT
180Ω
TEST
POINT
300pF
(SEE NOTE)
2.27V
51Ω
TEST
POINT
OUTPUT
TEHOZ OUTPUT LOW/HIGH
DISABLE LOAD CIRCUIT
TEST
POINT
OUTPUT
300pF
(SEE NOTE)
91Ω
OUTPUT
300pF
(SEE NOTE)
50pF
(SEE NOTE)
NOTE: Includes jig and stray capacitance.
Burn-In Circuits
MD82C86H CERDIP
VCC
C1
R1
F2
1
20
2
19
A
3
18
A
4
17
A
5
16
A
6
15
A
7
14
A
8
13
A
9
12
A
10
11
R1
F2
R1
F2
R1
F2
R1
F2
R1
F2
VCC
R1
F2
R2
R1
F2
R1
R1
4-322
A
R3
VCC
TEST
POINT
82C86H
Burn-In Circuits
(Continued)
MR82C86H CLCC
C1
VCC
F2
R5
3
F2
F2
F2
F2
F2
R5
R5
R5
R5
R5
F2
F2
R5
R5
2
F3
1
R5
20
19
18
4
17
5
R5
R5
R5
16
6
R5
15
7
R5
14
8
9
10
R4
F0
11
R4
F1
NOTES:
1. VCC = 5.5V ± 0.5V, GND = 0V
2. VIH = 4.5V ± 10%
3. VIL = -0.2V to 0.4V
4. R1 = 47kΩ ± 5%
5. R2 = 2.4kΩ ± 5%
6. R3 = 1.5kΩ ± 5%
7. R4 = 1kΩ ± 5%
8. R5 = 5kΩ ± 5%
9. C1 = 0.01µF minimum
10. F0 = 100kHz ± 10%
11. F1 = F0/2, F2 = F1/2, F3 = F2/2
4-323
12
R5
F3
13
R5
F3
F3
F3
F3
F3
F3
82C86H
Die Characteristics
DIE DIMENSIONS:
138.6 x 155.5 x 19 ± 1mils
GLASSIVATION:
Type: SiO2
Thickness: 8kÅ ± 1kÅ
METALLIZATION:
Type: Si - Al
Thickness: 11kÅ ± 1kÅ
WORST CASE CURRENT DENSITY:
1.47 x 105 A/cm2
Metallization Mask Layout
82C86H
A2
A1
A0
VCC
B0
B1
B2
A3
B3
A4
B4
A5
B5
A6
A7
OE
GND
T
B7
B6
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
4-324
Similar pages