Vishay CTS32 Hermetically sealed, axial-lead, to cecc specification Datasheet

CTS1, CTS13, CTS32, 749DX
Vishay Sprague
Hermetically Sealed, Axial-Lead,
To CECC Specifications
FEATURES
• Hermetically sealed metal case with plastic film insulation
• Extended capacitance range (type 749DX)
• High operational stability with both time and temperature
• Low leakage current
• Low dissipation factor
• Capability to withstand high inrush currents (type CTS32)
APPLICATIONS
Performance and reliability has been proven in a wide range
of applications such as: filtering, by-pass, coupling, energy
storage, timing circuits.
PERFORMANCE CHARACTERISTICS
SPECIFICATIONS
Operating Temperature:
- 55°C to + 85°C (types CTS13, CTS32)
- 55°C to + 125°C (types CTS1, 749DX)
CECC
30201-001
30201-002
30201-005
30201-011/012
30201-019
30201-029
749DX
CTS1
CTS13
749DX
CTS32
749DX
BS
9073-N001
749DX
IECQ
300201/FR001
CTS1
ORDERING INFORMATION
CTS13
TYPE
040
X0
CAPACITANCE DC VOLTAGE RATING
@ + 85°C
TOLERANCE
105
CAPACITANCE
Expressed in picofarads.
X0 = ± 20%
First two digits are significant. X9 = ± 10%
Third digit is the number of
X5 = ± 5%
zeros following.
(Special Order)
Expressed in volts.
Where necessary, zeros
precede the voltage rating
to complete the 3 digit
block 6R3 = 6.3 Volts
2
A
P
CASE CODE STYLE NUMBER PACKAGING
See Table
Ratings and
Case
Codes.
0 = Bare Case
2 = Plastic-Film
Insulation
See Taping and
Packaging
Identifies the Basic Capacitor Design
CTS1 = CECC 30201-002
CTS13 = CECC 30201-005
CTS32 = CECC 30201-019
749DX = CECC 30201-001/011/012/029
DIMENSIONS in millimeters
30 MIN.
L MAX.
30 MIN.*
D MAX.
ød
*23mm MAX. FOR TAPED CAPACITORS
CASE
CODE
BS
D MAX.
NF
D MAX.
L MAX.
+ 10%
Ød - 0.05
A
3.6
3.8
10.2
0.5
B
4.9
5.1
15.0
0.5
C
7.5
7.7
20.5
0.6
D
9.1
9.3
24.0
0.6
www.vishay.com
44
For technical questions, contact [email protected]
Document Number 42073
Revision 28-Mar-02
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TYPE CTS1: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+ 85°C)
CR
6.3V
10V
16V
25V
40V
50V
63V
80V
100V
125V
CATEGORY VOLTAGE UC (+125°C)
mF
40V
50V
67V
82V
0.10
4V
6.3V
10V
13V
25V
33V
A
A
A
A
0.12
A
A
A
A
0.15
A
A
A
A
0.18
A
A
A
A
0.22
A
A
A
A
0.27
A
A
A
A
A
0.33
A
A
A
A
A
0.39
A
A
A
A
B
0.47
A
A
A
A
A
B
0.56
A
A
A
A
A
B
0.68
A
A
A
A
B
B
0.82
A
A
B
B
B
B
1.0
A
A
B
B
B
B
1.2
1.5
A
A
B
B
B
B
B
B
B
B
B
B
B
1.8
A
B
B
B
B
B
B
2.2
A
B
B
B
B
B
B
2.7
A
B
B
B
B
B
3.3
A
B
B
B
B
C
3.9
A
B
B
B
B
C
4.7
A
B
B
C
C
C
5.6
A
B
C
C
C
C
6.8
A
B
C
C
C
C
8.2
B
C
C
C
C
10
B
C
C
C
C
12
B
C
C
D
D
15
B
C
C
D
D
18
B
C
C
D
C
D
22
B
27
B
33
B
C
D
C
D
39
B
C
D
47
B
C
D
56
B
68
C
D
C
D
82
C
D
100
C
D
120
C
150
C
180
D
D
D
220
D
270
D
330
D
Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10% or
± 5% (special order).
Document Number 42073
Revision 28-Mar-02
For technical questions, contact [email protected]
www.vishay.com
45
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TYPE CTS13: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+ 85°C)
CR
µF
40V
50V
63V
0.10
6.3V
10V
16V
20V
25V
A
A
A
0.12
A
A
A
0.15
A
A
A
0.18
A
A
A
0.22
A
A
A
0.27
A
A
A
0.33
A
A
A
0.39
A
A
A
0.47
A
A
A
0.56
A
A
A
0.68
A
A
A
0.82
A
A
B
1.0
A
A
B
A
A
B
B
A
B
1.2
1.5
B
B
1.8
A
B
B
B
2.2
A
B
B
B
2.7
A
B
B
B
3.3
A
B
B
B
3.9
A
B
B
B
4.7
A
B
B
C
5.6
A
B
C
C
6.8
A
B
C
C
B
C
C
C
B
8.2
10
C
C
C
12
B
C
C
D
15
B
C
C
D
D
18
B
C
C
22
B
C
D
27
B
33
C
B
C
D
D
39
B
C
D
47
B
C
D
56
B
C
68
D
C
82
C
100
C
D
120
C
D
150
C
D
180
D
D
D
220
D
270
D
330
D
Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10% or
± 5% (special order).
www.vishay.com
46
For technical questions, contact [email protected]
Document Number 42073
Revision 28-Mar-02
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
CTS32 STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+85°C)
CR
µF
6.3V
10V
16V
25V
1.0
40V
50V
63V
A
A
B
1.2
A
A
B
B
1.5
A
B
B
B
1.8
A
B
B
B
2.2
A
B
B
B
2.7
A
B
B
B
3.3
A
B
B
B
3.9
A
B
B
B
4.7
A
B
B
C
5.6
A
B
C
C
6.8
A
B
C
C
8.2
B
C
C
C
10
B
C
C
C
12
B
C
C
D
15
B
C
C
D
18
B
C
C
D
22
B
C
D
27
B
C
D
33
B
C
D
39
B
C
D
47
B
C
D
56
B
C
D
C
D
68
82
C
D
100
C
D
120
C
D
150
C
D
180
D
220
D
270
D
330
D
Preferred ratings are in bold caracters.Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or
± 5 % (special order).
Document Number 42073
Revision 28-Mar-02
For technical questions, contact [email protected]
www.vishay.com
47
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TYPE 749DX: STANDARD RATINGS AND CASE CODES
RATED VOLTAGE UR (+ 85°C)
CR
6.3V
10V
µF
16V
20V
25V
35V
40V
50V
63V
25V
33V
40V
CATEGORY VOLTAGE UC (+ 125°C)
4V
6.3V
10V
13V
16V
23V
0.068
A
0.085
A
0.10
A
A
0.12
A
A
A
A
0.15
A
A
A
0.18
A
A
A
0.22
A
A
A
0.27
A
A
A
0.33
A
A
A
0.39
A
A
A
0.47
A
A
A
0.56
A
A
A
0.68
A
A
0.82
A
A
A
B
1.0
A
A
A
B
A
1.2
A
B
B
B
B
1.5
A
B
B
B
B
1.8
A
B
B
B
B
2.2
A
B
B
B
B
2.7
A
B
B
B
B
3.3
A
B
B
B
B
3.9
A
B
B
B
B
4.7
A
B
B
*
C
5.6
A
B
B
C
C
6.8
A
*
*
C
C
8.2
B
C
C
C
C
10
B
C
C
C
C
12
B
C
C
C
D
15
B
C
C
C
D
D
18
B
C
C
C
22
B
C
C
D
27
B
C
D
D
33
B
C
D
D
39
B
C
D
D
C
D
47
B
56
B
68
C
D
C
D
82
C
D
100
C
D
120
C
150
C
180
C
220
*
D
D
D
D
270
D
330
D
*See extended range page
www.vishay.com
48
For technical questions, contact [email protected]
Document Number 42073
Revision 28-Mar-02
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TYPE 749DX: EXTENDED RATINGS AND CASE CODES
RATED VOLTAGE UR (+85°C)
CR
6.3V
10V
25V
35V
50V
16V
23V
32V
1.2
A
A
1.5
A
A
1.8
A
µF
16V
20V
CATEGORY VOLTAGE UC (+125°C)
4V
6.3V
10V
13V
2.2
A
2.7
A
3.3
A
3.9
A
A
4.7
A
A
5.6
A
6.8
A
8.2
B
B
B
A
10
B
A
12
A
B
15
A
B
18
B
22
B
B
C
27
B
C
D
33
B
C
D
39
B
C
D
47
B
C
56
B
C
D
68
B
C
D
82
B
D
100
B
C
C
D
120
B
C
C
D
150
C
180
C
D
D
220
C
D
270
C
D
D
330
C
D
390
C
D
470
C
560
D
D
D
680
D
820
D
1000
D
Preferred ratings are in bold caracters.Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or
± 5 % (special order).
Document Number 42073
Revision 28-Mar-02
For technical questions, contact [email protected]
www.vishay.com
49
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TYPICAL CURVES RIPPLE VOLTAGE @ + 25°C
100
10
5
4
3
2
100
50
40
30
20
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
6.3V
VOLTS RMS
VOLTS RMS
50
40
30
20
1
0.5
0.4
0.3
0.2
0.1
10
100
1K
10K
100K
5
4
3
2
5
4
3
2
1
0.5
0.4
0.3
0.2
0.1
10
1M
100
1K
10K
FREQUENCY IN HERTZ
Case A Capacitors
Case B Capacitors
100K
1M
100K
1M
100
50
40
30
20
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
6.3V
VOLTS RMS
VOLTS RMS
10
10
FREQUENCY IN HERTZ
100
50
40
30
20
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
6.3V
1
0.5
0.4
0.3
0.2
0.1
10
www.vishay.com
50
100
1K
10K
100K
1M
10
5
4
3
2
100V & 125V
80V
50V & 63V
35V & 40V
20V & 25V
16V
10V
6.3V
1
0.5
0.4
0.3
0.2
0.1
10
100
1K
10K
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
Case C Capacitors
Case D Capacitors
For technical questions, contact [email protected]
Document Number 42073
Revision 28-Mar-02
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1. Operating Temperature: - 55°C to + 85°C with rated DC
voltage UR applied.+ 85°C to + 125°C with linear voltage
derating to category voltage UC (only for types CTS1,
749DX)
2. Capacitance and Tolerance: Capacitance measured at
100Hz and + 25°C shall be within the specified tolerance
limits of the nominal rating. Capacitance measurement
shall be made by means of a polarized capacitance bridge.
The polarizing voltage shall be of 2.2 volts. The maximum
voltage applied during measurements shall be 1.0 volt rms
at 100 Hz and + 25°C.
3. Reverse Voltage: These capacitors are capable of
withstanding peak voltage in the reverse direction equal
to: 15% of the rated DC voltage at + 25°C, 5% of the rated
DC voltage at + 85°C
6. Dissipation factor: The dissipation factor, when
measured at 100 Hz, shall not exceed the values below:
Table 3
CTS1/CTS13/CTS32
TEMP.
SURGE VOLTAGE SURGE VOLTAGE
@ + 85°C
@ + 125°C
CTS13/CTS32
1.30 UR
–
749DX/CTS1
1.30 UR
1.30 UC
Capacitors shall withstand the surge voltage applied in
series with a 1000 ohm resistor, at the rate of one halfminute on, five and a half-minute off, for 1000 successive
test cycles at + 85°C or at + 125°C. After test, dissipation
factor and leakage current shall meet the initial
requirements at + 25°C (see below), capacitance change
shall not exceed ± 10% of initial value at + 25°C.
5. Leakage current: Rated voltage UR shall be applied to
capacitors during five minutes with a resistor of 1000 ohm
in series with each capacitor, before making DC leakage
current measurements. The leakage current shall not
exceed the following limits:
Table 2
+ 25°C
+ 85°C
+125°C
Document Number 42073
Revision 28-Mar-02
CR > 100
- 55°C
9%
11%
8%
10%
+ 25°C
6%
8%
6%
8%
+ 85°C
9%
11%
–
–
+ 125°C*
12%
14%
10%
11%
*not applicable for CTS13/32
7. Stability at low and high temperature: Capacitance
change with temperature shall not exceed the limits of
the following table, leakage current and dissipation factor
shall be within the limits specified in Tables 2 and 3.
TEMPERATURE
TEMPERATURE
CR ≤ 100
Table 4
4. Surge Voltage: Table 1
PRODUCT TYPE
749DX
CRUR ≤ 1900 CRUR > 1900
CTS1/CTS13/CTS32/749DX
0.01 CR x UR or
1µA whichever is greater
0.1 CR x UR or
10µA whichever is greater
0.125 CR x UR or
12.5µA whichever is greater
CTS1/CTS13/CTS32/749DX
- 55°C
- 10%
+ 85°C
+ 12%
+ 125°C *
+ 15%
*not applicable for CTS13/32
8. Impedance: The impedance measured at 100 kHz and
25°C shall not exceed the following values:
Table 5
CASE CODE
Z (Ω) *
A
10
B
5
C
2
D
1
* not applicable for CR ≤ 0.68 µF
9. Life test: After 2000 hours at + 85°C with rated DC
voltage applied, or after 2000 hours at + 125°C with
category DC voltage applied (for types CTS1, 749DX only)
capacitors shall meet the requirements in table 6.
Table 6
PRODUCT CAPACITANCE DISSIPATION
TYPE
CHANGE
FACTOR
DC LEAKAGE
CURRENT
CTS1
Within
Within
CTS13
±10% of
initial
of initial
CTS32
initial value
requirement
requirements
749DX
@ +25°C
@ +25°C
@ +25°C
For technical questions, contact [email protected]
Within 125%
www.vishay.com
51
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
PERFORMANCE CHARACTERISTICS (CONT’D)
GUIDE TO APPLICATION
10.Humidity test: After 56 days (1350 hours) at + 40°C, 90
to 95% of relative humidity (per IEC 68-2-3) with no
voltage applied, capacitors shall meet the requirements
in table 7 below.
Table 7
1. AC Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
Irms
=
P
RESR
where
CAPACITANCE CHANGE
Within ± 3% of initial value
P = Power Dissipation in Watts at + 25°C as given below
DC LEAKAGE CURRENT
Within initial requirement
@ +25°C - Table 2
RESR = The capacitor Equivalent Series Resistance at the
specified frequency.
DISSIPATION FACTOR
Within initial requirement
@ +25°C - Table 3
11.Charge-discharge test (CTS32): Capacitors shall
withstand 1,000,000 cycles at + 85°C of 0.5 second
charge at DC rated voltage, 0.5 second discharge in an
equivalent load resistance of the test fixture lower than
0.5 ohm. Following test, capacitors shall meet the
requirements in table 8 below.
Table 8
CAPACITANCE CHANGE
Within ± 5% of initial value
@ + 25°C
DC LEAKAGE CURRENT
Within initial requirement
@ +25°C - Table 2
DISSIPATION FACTOR
Within initial requirement
@ +25°C - Table 3
Typical values of charge-discharge current (per above test
conditions)
RATED VOLTAGE
UR (V)
CHARGE-DISCHARGE CURRENT
(A)
2. AC Ripple Current: The maximum allowable ripple
voltage shall be determined from the formula:
Vrms =
P
RESR
x Z, where
Z = The capacitor Impedance at the specified frequency.
The calculations are summarized on the graphs page 7
giving the maximum available ripple voltage as a function
of frequency.
However, the sum of the peak AC voltage plus the DC
voltage shall not exceed the rated DC voltage at + 85°C
of the capacitor. The sum of the negative peak AC voltage
plus the DC voltage shall not allow a voltage reversal
exceeding 15% of the rated DC voltage.
3. AC Ripple Current or Voltage Derating Factor: If these
capacitors are to be operated at temperatures above
+ 25°C, the permissible rms ripple current or voltage shall
be calculated using the derating factors in the table below:
6.3
13
10
20
16
32
25
50
+ 25°C
1.0
40
80
+ 55°C
0.8
50
100
+ 85°C
0.6
63
126
+ 125°C
0.4
12.Insulation test: For capacitors with insulating sleeves,
a DC voltage of 100 volts shall be applied for one minute
between the case of the capacitor and a metal “V” block
in intimate contact with the insulating sleeve.
The insulating resistance measured in these conditions
shall be at least 100 megohms.
13.Lead pull test: Leads shall withstand the following test
(IEC 68 - 2 - 2):
TEMPERATURE
DERATING FACTOR
4. Power Dissipation: Power dissipation will be affected
by the heat sinking capability of the mounting surface.
Non-sinusoidial ripple current may produce heating effects
which differ from those shown in the following table. It is
important that the equivalent Irms value be established
when calculating permissible operating levels.
CASE
CODE
POWER DISSIPATION
@ + 25°C (WATTS)
• Tensile stress of 5N (cases A and B) or 10N (cases C
and D) for 10 seconds in any direction
A
0.115
B
0.145
• One bend in each direction
C
0.185
• Two consecutive rotations of 180°
D
0.225
www.vishay.com
52
For technical questions, contact [email protected]
Document Number 42073
Revision 28-Mar-02
CTS1, CTS13, CTS32, 749DX
Hermetically Sealed, Axial-Lead,
To CECC Specifications
Vishay Sprague
TAPE AND REEL PACKAGING
S
MEETS IEC 286-1
1.5 max.
L1 - L2 = 1.5mm max
S = component spacing (cumulative
tolerance on 20 units = 4mm)
b = tape spacing
c = overall length
0.2 ± 0.3
L1
L2
b
c
DIMENSIONS in millimeters
REEL PACK
AMMO PACK
CASE
SIZE
REEL AND
AMMO
S
OPTION P
OPTION R
b
c
MAX
b
c
MAX
A
5.0 ± 0.3
63 ± 2
78
53 ± 2
B
5.0 ± 0.3
63 ± 2
78
C
10.0 ± 0.3
63 ± 2
D
10.0 ± 0.3
63 ± 2
PACKAGING CODE
P
OPTION G
QTY PER
REEL
b
c
MAX
68
2500
53 ± 2
68
1500
53 ± 2
68
2500
53 ± 2
68
1000
78
63 ± 2
78
1000
53 ± 2
68
250
78
63 ± 2
78
500
53 ± 2
68
250
R
QTY PER
BOX
G
MARKING
Capacitors shall be marked with SPRAGUE and/or the registered trademark 2 at vendor‘s option ; the type number ; rated
capacitance and tolerance (with a letter code, if different from ± 20%, K = ± 10% ; J = ± 5%) ; rated DC voltage at + 85°C and
the date code of manufacture.
Capacitors shall be marked on one end with a “plus” sign (+) to identify the positive terminal.
Document Number 42073
Revision 28-Mar-02
For technical questions, contact [email protected]
www.vishay.com
53
Similar pages