RSG CXOMHGSNSM5 Cxomhg oscillator Datasheet

CXOMHG OSCILLATOR
300 kHz to 120 MHz
High Shock, Low Profile, Miniature
Surface Mount Crystal Oscillator
™
DESCRIPTION
GM
M
4.19
Intended for applications requiring shock survivability to
10,000 g (and higher), Statek’s surface-mount CXOMHG
oscillators are high-shock versions of the CXOM oscillators.
These oscillators consist of a Statek miniature quartz crystal
and a CMOS/TTL compatible hybrid circuit in a low-profile
ceramic package with an extremely small footprint.
actual size
side view
FEATURES
High shock resistance
Designed for surface mount applications using infrared,
vapor phase, or epoxy mount techniques
PACKAGE DIMENSIONS
Hermetically sealed ceramic package
CMOS and TTL compatible
D
Low power consumption
2
Optional Output Enable/Disable with Tri-State
A
Low EMI emission
TOP
3
BOTTOM
1
Full military testing available
4
D
APPLICATIONS
B
Military & Aerospace
E
C
Smart munitions
Projectile electronics
TYPICAL
Industrial
Engine control
Down-hole drilling
MAXIMUM
DIM
inches
mm
inches
mm
A
0.256
6.50
0.263
6.68
B
0.197
5.00
0.204
5.18
C (SM1)
0.051
1.30
0.055
1.40
C (SM3/SM5)
SUGGESTED LAND PATTERN
0.055
1.40
0.063
1.60
D
0.055
1.40
0.065
1.65
E
0.060
1.52
0.070
1.78
0.070 (1.78)
0.067 (1.70)
PIN CONNECTIONS
0.065 (1.65)
1. Enable/Disable (E or T) or not connected (N)
2. Ground
0.201 (5.11)
3. Output
0.136 (3.45)
4. VDD
GRID
PLACEMENT
COURTYARD
■
■
■
90
Änderungen vorbehalten / subject to change without notice
■
IS O
■
10160 Rev A
YS
01
TEM
C ERT I F I C
AT
N
IO
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de
S
0.137 (3.48)
inches (mm)
Pb
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
O
Specifications are typical at 25 C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage1
Supply Voltage VDD
-0.5V to 7.0V
Storage Temperature
-55OC to +125OC
Maximum Process Temperature 260OC fo 20 seconds
5.0 V
Calibration Tolerance2
+
_
Frequency Stability
Over Temperature3
+
_
Supply Current (Typical)
ENABLE/DISABLE OPTIONS (E/T/N)
100 ppm
Output Load (CMOS)4
15 pF
Start-up Time
Rise/Fall Time
5 ms MAX
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
Aging, first year
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table compares the E and T
versions.
50 ppm for Commercial
+
_ 100 ppm for Industrial
+
_ 100 ppm for Military
10 MHz
4 mA
24 MHz
8 mA
30 MHz 10 mA
40 MHz 12 mA
50 MHz 14 mA
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
10 ppm MAX
Shock, survival
10,000 g, 0.3 ms, 1/2 sine
Vibration, survival6
20 g, 10-2,000 Hz swept sine
5
O
E
T
When enabled (PIN 1 is high*)
O
Operating Temp Ranges -10 C to +70 C (Commercial)
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
1. Other voltages available. For 3.3 V, see CXO3MHG data sheet. For others,
contact factory.
2. Other tolerances available.
3. Does not include calibration tolerance. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. Higher shock version available. Contact factory for requirements above 10,000 g.
6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
Output
Freq. output
Freq. output
Oscillator
Oscillates
Oscillates
Current consumption
Normal
Normal
Output
High Z state
High Z state
Oscillator
Stops
Oscillates
Current consumption
Very low
Lower than normal
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
Output recovery
PACKAGING OPTIONS
Delayed
Immediate
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
CXOMHG - Tray Pack
- 16 mm tape, 7˝or 13˝ reels
Per EIA 418 (see Tape and Reel data sheet 10109)
HOW TO ORDER CXOMHG SURFACE MOUNT CRYSTAL OSCILLATORS
S
T
SM3
32.0M
,
“S” if special or
custom design.
Blank if Std.
Enable/Disable
Option
E, T, or N
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
Frequency
K = kHz
M = MHz
100
/
100
I
/
Frequency
Stability over
Temp.Range
(in ppm)
Calibration
Tolerance
@ 250C
(in ppm)
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
■
■
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
10160 Rev A
YS
■
IS O
90
Änderungen vorbehalten / subject to change without notice
■
■
I
01
TEM
C ERT I F I C
AT
N
IO
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de
/
S
CXOMHG
Pb
Similar pages