CY22392 Three-PLL General Purpose FLASH Programmable Clock Generator Features ■ Three integrated phase-locked loops ■ Ultra Wide Divide Counters (8-bit Q, 11-bit P, and 7-bit Post Divide) ■ Improved Linear Crystal Load capacitors ■ Flash programmability ■ Field programmable ■ Low-jitter, high-accuracy outputs ■ Power-management options (Shutdown, OE, Suspend) ■ Configurable Crystal drive strength ■ Frequency Select through 3 external LVTTL Inputs ■ 3.3V operation ■ 16-pin TSSOP packages ■ CyClocksRT™ Support Benefits ■ ■ Generates up to 3 unique frequencies on 6 outputs up to 200 MHz from an external source. Functional upgrade for current CY2292 family. Allows for 0 ppm Frequency Generation and Frequency Conversion under the most demanding applications. ■ Improves frequency accuracy over temperature, age, process, and initial offset. ■ Non-Volatile programming enables easy customization, ultra-fast turnaround, performance tweaking, design timing margin testing, inventory control, lower part count, and more secure product supply. In addition, any part in the family can also be programmed multiple times which reduces programming errors and provides an easy upgrade path for existing designs. ■ In-house programming of samples and prototype quantities is available using the CY3672 FTG Development Kit. Production quantities are available through Cypress Semiconductor’s value added Distribution partners or by using third party programmers from BP Microsystems, HiLo Systems, and others. ■ Performance suitable for high-end multimedia, communications, industrial, A/D Converters, and consumer applications. ■ Supports numerous low-power application schemes and reduces EMI by allowing unused outputs to be turned off. ■ Adjust Crystal Drive Strength for compatibility with virtually all crystals. ■ 3-Bit External Frequency Select Options for PLL1, CLKA, and CLKB. ■ Industry-standard supply voltage. ■ Industry-standard packaging saves on board space. ■ Easy to use software support for design entry. Logic Block Diagram XTALIN XTALOUT XBUF OSC. CONFIGURATION FLASH PLL1 11 BIT P 8 BIT Q SHUTDOWN/OE PLL2 S0 11 BIT P 8 BIT Q S1 S2/SUSPEND 4x4 Crosspoint Switch PLL3 11 BIT P 8 BIT Q Cypress Semiconductor Corporation Document #: 38-07013 Rev. *E • 198 Champion Court • Divider /2,3, or 4 CLKE Divider 7 BIT CLKD Divider 7 BIT CLKC Divider 7 BIT CLKB Divider 7 BIT CLKA San Jose, CA 95134-1709 • 408-943-2600 Revised October 10, 2008 [+] Feedback CY22392 Pinouts Figure 1. CY22392 - 16-pin TSSOP CLKC 1 16 VDD 2 15 S2/SUSPEND SHUTDOWN/OE AGND 3 14 AVDD XTALIN 4 13 S1 XTALOUT XBUF 5 12 6 11 S0 GND CLKD 7 10 CLKA CLKE 8 9 CLKB Pin Definitions Name CLKC Pin Number 1 Description Configurable clock output C VDD 2 Power supply AGND 3 Analog Ground XTALIN 4 Reference crystal input or external reference clock input XTALOUT 5 Reference crystal feedback XBUF 6 Buffered reference clock output CLKD 7 Configurable clock output D CLKE 8 Configurable clock output E CLKB 9 Configurable clock output B CLKA 10 Configurable clock output A GND 11 Ground S0 12 General Purpose Input for Frequency Control; bit 0 S1 13 General Purpose Input for Frequency Control; bit 1 AVDD 14 Analog Power Supply S2/ SUSPEND 15 General Purpose Input for Frequency Control; bit 2. Optionally Suspend mode control input. SHUTDOWN/OE 16 Places outputs in three-state condition and shuts down chip when LOW. Optionally, only places outputs in tristate condition and does not shut down chip when LOW Document #: 38-07013 Rev. *E Page 2 of 9 [+] Feedback CY22392 Operation applications that requirements. The CY22392 is an upgrade to the existing CY2292. The new device has a wider frequency range, greater flexibility, improved performance, and incorporates many features that reduce PLL sensitivity to external system issues. The value of the load capacitors is determined by six bits in a programmable register. The load capacitance can be set with a resolution of 0.375 pF for a total crystal load range of 6 pF to 30 pF. The device has three PLLs which, when combined with the reference, allow up to four independent frequencies to be output on up to six pins. These three PLLs are completely programmable. For driven clock inputs the input load capacitors may be completely bypassed. This enables the clock chip to accept driven frequency inputs up to 166 MHz. If the application requires a driven input, then XTALOUT must be left floating. Configurable PLLs Output Configuration PLL1 generates a frequency that is equal to the reference divided by an 8-bit divider (Q) and multiplied by an 11-bit divider in the PLL feedback loop (P). The output of PLL1 is sent to the crosspoint switch. The output of PLL1 is also sent to a /2, /3, or /4 synchronous post-divider that is output through CLKE. The frequency of PLL1 can be changed by external CMOS inputs, S0, S1, S2. See the following section on General-Purpose Inputs for more details. Under normal operation there are four internal frequency sources that may be routed through a programmable crosspoint switch to any of the four programmable 7-bit output dividers. The four sources are: reference, PLL1, PLL2, and PLL3. In addition, many outputs have a unique capability for even greater flexibility. The following is a description of each output. PLL2 generates a frequency that is equal to the reference divided by an 8-bit divider (Q) and multiplied by an 11-bit divider in the PLL feedback loop (P). The output of PLL2 is sent to the crosspoint switch. PLL3 generates a frequency that is equal to the reference divided by an 8-bit divider (Q) and multiplied by an 11-bit divider in the PLL feedback loop (P). The output of PLL3 is sent to the cross-point switch. General-Purpose Inputs S0, S1, and S2 are general-purpose inputs that can be programmed to allow for eight different frequency settings. Options that may be switched with these general purpose inputs are as follows; the frequency of PLL1, the output divider of CLKB, and the output divider of CLKA. CLKA and CLKB both have 7-bit dividers that point to one of two programmable settings (register 0 and register 1). Both clocks share a single register control, so both must be set to register 0, or both must be set to register 1. For example: the part may be programmed to use S0, S1, and S2 (0,0,0 to 1,1,1) to control eight different values of P and Q on PLL1. For each PLL1 P and Q setting, one of the two CLKA and CLKB divider registers can be chosen. Any divider change as a result of switching S0, S1, or S2 is guaranteed to be glitch free. are sensitive to absolute frequency CLKA’s output originates from the crosspoint switch and goes through a programmable 7-bit post divider. The 7-bit post divider derives its value from one of two programmable registers. Each of the eight possible combinations of S0, S1, S2 controls which of the two programmable registers is loaded into CLKA’s 7-bit post divider. See the section “General-Purpose Inputs” for more information. CLKB’s output originates from the crosspoint switch and goes through a programmable 7-bit post divider. The 7-bit post divider derives its value from one of two programmable registers. Each of the eight possible combinations of S0, S1, and S2 controls which of the two programmable registers is loaded into CLKA’s 7-bit post divider. See the section “General-Purpose” Inputs for more information. CLKC’s output originates from the crosspoint switch and goes through a programmable 7-bit post divider. The 7-bit post divider derives its value from one programmable register. CLKD’s output originates from the crosspoint switch and goes through a programmable 7-bit post divider. The 7-bit post divider derives its value from one programmable register. CLKE’s output originates from PLL1 and goes through a post divider that may be programmed to /2, /3, or /4. XBUF is simply the buffered reference. Crystal Input The Clock outputs have been designed to drive a single point load with a total lumped load capacitance of 15 pF. While driving multiple loads is possible with the proper termination it is generally not recommended. The input crystal oscillator is an important feature of this device because of its flexibility and performance features. Power Saving Features The oscillator inverter has programmable drive strength. This allows for maximum compatibility with crystals from various manufacturers, processes, performances, and qualities. The input load capacitors are placed on-die to reduce external component cost. These capacitors are true parallel-plate capacitors for ultra-linear performance. These were chosen to reduce the frequency shift that occurs when non-linear load capacitance interacts with load, bias, supply, and temperature changes. Non-linear (FET gate) crystal load capacitors must not be used for MPEG, POTS dial tone, communications, or other Document #: 38-07013 Rev. *E The SHUTDOWN/OE input three-states the outputs when pulled LOW. If system shutdown is enabled, a LOW on this pin also shuts off the PLLs, counters, the reference oscillator, and all other active components. The resulting current on the VDD pins is less than 5 μA (typical). After leaving shutdown mode, the PLLs will have to relock. The S2/SUSPEND input can be configured to shut down a customizable set of outputs and/or PLLs, when LOW. All PLLs and any of the outputs can be shut off in nearly any combination. The only limitation is that if a PLL is shut off, all outputs derived from it must also be shut off. Suspending a PLL shuts off all Page 3 of 9 [+] Feedback CY22392 associated logic, while suspending an output simply forces a three-state condition. can download a copy of CyClocksRT for free on Cypress’s web site at www.cypress.com. Improving Jitter Junction Temperature Limitations Jitter Optimization Control is useful in mitigating problems related to similar clocks switching at the same moment, causing excess jitter. If one PLL is driving more than one output, the negative phase of the PLL can be selected for one of the outputs (CLKA–CLKD). This prevents the output edges from aligning, allowing superior jitter performance. It is possible to program the CY22392 such that the maximum Junction Temperature rating is exceeded. The package θJA is 115 C/W. Use the CyClocksRT power estimation feature to verify that the programmed configuration meets the Junction Temperature and Package Power Dissipation maximum ratings. Power Supply Sequencing Maximum Ratings For parts with multiple VDD pins, there are no power supply sequencing requirements. The part is not be fully operational until all VDD pins have been brought up to the voltages specified in the “Operating Conditions” table. Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Supply Voltage................................................–0.5V to +7.0V All grounds must be connected to the same ground plane. CyClocksRT™ Software DC Input Voltage ........................... –0.5V to + (AVDD + 0.5V) Storage Temperature ................................. –65°C to +125°C Junction Temperature .................................................. 125°C CyClocksRT is our second-generation application that allows users to configure this device. The easy-to-use interface offers complete control of the many features of this family including input frequency, PLL and output frequencies, and different functional options. Data sheet frequency range limitations are checked and performance tuning is automatically applied. CyClocksRT also has a power estimation feature that allows you to see the power consumption of your specific configuration. You Data Retention at Tj = 125°C .................................>10 years Maximum Programming Cycles........................................100 Package Power Dissipation...................................... 350 mW Static Discharge Voltage (per MIL-STD-883, Method 3015) .......................................... 2000V Latch up (per JEDEC 17) .................................... > ±200 mA Operating Conditions[1] Parameter Description VDD/AVDD Supply Voltage TA Commercial Operating Temperature, Ambient Industrial Operating Temperature, Ambient Min Typ. Max Unit 3.135 3.3 3.465 V 0 – +70 °C –40 – +85 °C CLOAD_OUT Max. Load Capacitance – – 15 pF fREF External Reference Crystal 8 – 30 MHz External Reference Clock[2], Commercial 1 – 166 MHz [2], External Reference Clock tPU Industrial Power up time for all VDD's to reach minimum specified voltage (power ramps must be monotonic) 1 – 150 MHz 0.05 – 500 ms Notes 1. Unless otherwise noted, Electrical and Switching Characteristics are guaranteed across these operating conditions. 2. External input reference clock must have a duty cycle between 40% and 60%, measured at VDD/2. Document #: 38-07013 Rev. *E Page 4 of 9 [+] Feedback CY22392 Switching Characteristics Parameter 1/t1 t2 Name Output Frequency Description [3, 4] Output Duty Cycle[3, 5] Min. Typ. Max. Unit Clock output limit, Commercial – – 200 MHz Clock output limit, Industrial – – 166 MHz Duty cycle for outputs, defined as t2 ÷ t1, Fout < 100 MHz, divider >= 2, measured at VDD/2 45% 50% 55% Duty cycle for outputs, defined as t2 ÷ t1, Fout > 100 MHz or divider = 1, measured at VDD/2 40% 50% 60% t3 Rising Edge Slew Rate[3] Output clock rise time, 20% to 80% of VDD 0.75 1.4 – V/ns t4 Falling Edge Slew Rate[3] Output clock fall time, 20% to 80% of VDD 0.75 1.4 – V/ns t5 Output three-state Timing[3] Time for output to enter or leave three-state mode after SHUTDOWN/OE switches – 150 300 ns t6 Clock Jitter[3, 6] Peak-to-peak period jitter, CLK outputs measured at VDD/2 – 400 – ps t7 Lock Time[3] PLL Lock Time from Power up – 1.0 3 ms Switching Waveforms Figure 2. All Outputs, Duty Cycle and Rise/Fall Time t1 t2 OUTPUT t3 t4 Figure 3. Output Three-State Timing OE t5 t5 ALL THREE-STATE OUTPUTS Figure 4. CLK Output Jitter t6 CLK OUTPUT Notes 3. Guaranteed by design, not 100% tested. 4. Guaranteed to meet 20%–80% output thresholds and duty cycle specifications. 5. Reference Output duty cycle depends on XTALIN duty cycle. 6. Jitter varies significantly with configuration. Reference Output jitter depends on XTALIN jitter and edge rate. Document #: 38-07013 Rev. *E Page 5 of 9 [+] Feedback CY22392 Switching Waveforms (continued) Figure 5. Frequency Change SELECT OLD SELECT Fold NEW SELECT STABLE t7 Fnew OUTPUT Test Circuit AVDD 0.1 μF OUTPUTS CLK out CLOAD VDD 0.1 μF GND Document #: 38-07013 Rev. *E Page 6 of 9 [+] Feedback CY22392 Ordering Information Ordering Code [8] Package Name Package Type Operating Range Operating Voltage CY22392FC Z16 16-TSSOP Commercial (TA = 0°C to 70°C) 3.3V CY22392FCT[8] Z16 16-TSSOP – Tape and Reel Commercial (TA = 0°C to 70°C) 3.3V Z16 16-TSSOP Commercial (TA = 0°C to 70°C) 3.3V Z16 16-TSSOP – Tape and Reel Commercial (TA = 0°C to 70°C) 3.3V Z16 16-TSSOP Industrial (TA = –40°C to 85°C) 3.3V Z16 16-TSSOP – Tape and Reel Industrial (TA = –40°C to 85°C) 3.3V 3.3V CY22392ZC-xxx [7, 8] CY22392ZC-xxxT[7, 8] CY22392ZI-xxx [7, 8] [7, 8] CY22392ZI-xxxT FTG Programmer CY3672-USB CY22392F, CY22393F CY22394F and CY22395F Adapter for CY3672-USB CY3698 Pb Free CY22392FXC Z16 16-TSSOP Commercial (TA = 0°C to 70°C) CY22392FXCT Z16 16-TSSOP – Tape and Reel Commercial (TA = 0°C to 70°C) 3.3V CY22392FXI Z16 16-TSSOP Industrial (TA = –40°C to 85°C) 3.3V CY22392FXIT Z16 16-TSSOP – Tape and Reel Industrial (TA = –40°C to 85°C) 3.3V CY22392ZXC-xxx[7] Z16 16-TSSOP Commercial (TA = 0°C to 70°C) 3.3V CY22392ZXC-xxxT[7] Z16 16-TSSOP – Tape and Reel Commercial (TA = 0°C to 70°C) 3.3V CY22392ZXI-xxx[7] Z16 16-TSSOP Industrial (TA = –40°C to 85°C) 3.3V CY22392ZXI-xxxT[7] Z16 16-TSSOP – Tape and Reel Industrial (TA = –40°C to 85°C) 3.3V Note 7. The CY22392ZC-xxx, CY22392ZI-xxx, CY22392ZXC-xxx, and CY22392ZXI-xxx are factory programmed configurations. Factory programming is available for high-volume design opportunities of 100 Ku/year or more in production. For more details, contact your local Cypress FAE or Cypress Sales Representative. 8. Not recommended for new designs. Document #: 38-07013 Rev. *E Page 7 of 9 [+] Feedback CY22392 Package Diagram Figure 6. 16-lead TSSOP 4.40 MM Body Z16.173 PIN 1 ID DIMENSIONS IN MM[INCHES] MIN. MAX. 1 REFERENCE JEDEC MO-153 6.25[0.246] 6.50[0.256] PACKAGE WEIGHT 0.05 gms PART # 4.30[0.169] 4.50[0.177] Z16.173 STANDARD PKG. ZZ16.173 LEAD FREE PKG. 16 0.65[0.025] BSC. 0.19[0.007] 0.30[0.012] 1.10[0.043] MAX. 0.25[0.010] BSC GAUGE PLANE 0°-8° 0.076[0.003] 0.85[0.033] 0.95[0.037] 4.90[0.193] 5.10[0.200] 0.05[0.002] 0.15[0.006] SEATING PLANE 0.50[0.020] 0.70[0.027] 0.09[[0.003] 0.20[0.008] 51-85091-*A Document #: 38-07013 Rev. *E Page 8 of 9 [+] Feedback CY22392 Document History Page Document Title: CY22392 Three PLL General Purpose Flash Programmable Clock Generator Document Number: 38-07013 REV. ECN Orig. of Change Submission Date Description of Change ** 106738 TLG 07/03/01 New Data Sheet *A 108515 JWK 08/23/01 Updates based on characterization results. Removed “Preliminary” heading. Added paragraph on Junction Temperature limitations and part configurations. Removed soldering temperature rating. Split crystal load into two typical specs representing digital settings range. Changed t5 max to 300 ns. Changed t7 typical to 1.0 ms. *B 110052 CKN 12/09/01 Preliminary to Final. *C 121864 RBI 12/14/02 Power up requirements added to Operating Conditions Information *D 237811 RGL See ECN Added Lead Free Devices *E 2584052 AESA 10/10/08 Updated template. Added Note “Not recommended for new designs.” Added part number CY22392FC, CY22392FCT, CY22392ZC-xxxT, CY22392ZI-xxxT, CY3672-USB, CY3698, CY22392FXCT, CY22392FXIT, CY22392ZXC-xxxT, and CY22392ZXI-xxxT, in ordering information table. Removed part number CY22392FI in ordering information table. Changed Lead-Free to Pb-Free. Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products PSoC Clocks & Buffers PSoC Solutions psoc.cypress.com clocks.cypress.com General Low Power/Low Voltage psoc.cypress.com/solutions psoc.cypress.com/low-power Wireless wireless.cypress.com Precision Analog Memories memory.cypress.com LCD Drive psoc.cypress.com/lcd-drive image.cypress.com CAN 2.0b psoc.cypress.com/can USB psoc.cypress.com/usb Image Sensors psoc.cypress.com/precision-analog © Cypress Semiconductor Corporation, 2001-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 38-07013 Rev. *E Revised October 10, 2008 Page 9 of 9 CyClocksRT is a trademark of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback