TI CY74FCT163827CPAC 20-bit buffer Datasheet

Data sheet acquired from Cypress Semiconductor Corporation.
Data sheet modified to remove devices not offered.
CY74FCT163827
20-Bit Buffer
SCCS049 - March 1997 - Revised March 2000
Features
Functional Description
• Low power, pin-compatible replacement for LCX and
LPT families
• 5V tolerant inputs and outputs
• 24 mA & 6 mA balanced drive outputs
• Power-off disable outputs permits live insertion
• Edge-rate control circuitry for reduced noise
• FCT-C speed at 4.1 ns
• Latch-up performance exceeds JEDEC standard no. 17
• Typical output skew < 250 ps
• Industrial temperature range of –40˚C to +85˚C
• TSSOP (19.6-mil pitch) or SSOP (25-mil pitch)
• Typical Volp (ground bounce) performance exceeds Mil
Std 883D
• VCC = 2.7V to 3.6V
• ESD (HBM) > 2000V
Logic Block Diagrams CY74FCT163827
The CY74FCT163827 is a 20-bit buffer/line driver that provides
high-performance bus interface buffering for wide data/address
paths or buses carrying parity. It can be used as a single 20-bit
buffer or two 10-bit buffers. Each 10-bit buffer has a pair of NANDed
OE for increased flexibility.
The CY74FCT163827 has 24-mA balanced output drivers
with current limiting resistors in the outputs. This reduces the
need for external terminating resistors and provides for
minimal undershoot and reduced ground bounce. The inputs
and outputs were designed to be capable of being driven by
5.0V buses, allowing its use in mixed voltage systems as a
translator. The outputs are also designed with a power-off
disable feature enabling its use in applications requiring live
insertion.
Pin Configuration
SSOP/TSSOP
Top View
1OE1
1OE1
1
56
1OE2
1Y1
2
55
1A 1
1Y2
3
54
1A 2
GND
4
53
GND
1Y3
5
52
1A 3
1Y4
6
51
1A 4
VCC
7
50
VCC
8
49
1A 5
1Y6
9
48
1Y7
10
1A 7
GND
1Y8
11
47
46
45
1A 8
1Y9
12
13
44
1A 9
1Y10
14
43
1A 10
2OE1
2Y1
15
42
2A 1
2OE2
2Y2
16
41
2A 2
2Y3
17
40
2A 3
GND
18
39
GND
2Y4
19
38
2A 4
2Y5
20
37
2A 5
2Y6
21
36
2A 6
VCC
2Y7
22
35
VCC
23
34
2A 7
1OE2
1Y1
1A1
1Y5
TO 9 OTHER CHANNELS
2A1
FCT163827-1
2Y1
TO 9 OTHER CHANNELS
FCT163827-2
1A 6
GND
2Y8
24
GND
25
33
32
2Y9
26
31
2A 9
2Y10
27
30
2A10
2OE1
28
29
2OE2
Copyright
2A 8
GND
© 2000, Texas Instruments Incorporated
CY74FCT163827
Maximum Ratings[2, 3]
Pin Description
Name
Description
OE
Output Enable Inputs (Active LOW)
A
Data Inputs
Y
Three-State Outputs
(Above which the useful life may be impaired. For user
guidelines, not tested.)
Storage Temperature ................................ −55°C to +125°C
Ambient Temperature with
Power Applied............................................ −55°C to +125°C
Supply Voltage Range ..................................... 0.5V to +4.6V
Function Table[1]
DC Input Voltage .................................................−0.5V to +7.0V
Inputs
Outputs
DC Output Voltage ..............................................−0.5V to +7.0V
OE1
OE2
A
Y
L
L
L
L
DC Output Current
(Maximum Sink Current/Pin) ...........................−60 to +120 mA
L
L
H
H
Power Dissipation .......................................................... 1.0W
H
X
X
Z
Operating Range
X
H
X
Z
Range
Commercial
Ambient
Temperature
VCC
–40°C to +85°C
2.7V to 3.6V
Electrical Characteristics Over the Operating Range VCC=2.7V to 3.6V
Parameter
Description
Test Conditions
VIH
Input HIGH Voltage
All Inputs
VIL
Input LOW Voltage
VH
Input Hysteresis[5]
VIK
Input Clamp Diode Voltage
VCC=Min., IIN=–18 mA
IIH
Input HIGH Current
IIL
Min.
Typ.[4]
2.0
Max.
Unit
5.5
V
0.8
100
–0.7
V
mV
– 1.2
V
VCC=Max., VI=5.5
±1
µA
Input LOW Current
VCC=Max., VI=GND
±1
µA
IOZH
High Impedance Output Current
(Three-State Output pins)
VCC=Max., VOUT=5.5V
±1
µA
IOZL
High Impedance Output Current
(Three-State Output pins)
VCC=Max., VOUT=GND
±1
µA
IOS
Short Circuit Current[6]
VCC=Max., VOUT=GND
–240
mA
IOFF
Power-Off Disable
VCC=0V, VOUT≤4.5V
±100
µA
ICC
Quiescent Power Supply Current
VIN≤0.2V,
VIN>VCC–0.2V
VCC=Max.
0.1
10
µA
∆ICC
Quiescent Power Supply Current
(TTL inputs HIGH)
VIN=VCC–0.6V[7]
VCC=Max.
2.0
30
µA
–60
–135
Note:
1. H = HIGH Voltage Level, L = LOW Voltage Level, X = Don’t Care, Z = HIGH Impedance.
2. Operation beyond the limits set forth may impair the useful life of the device. Unless otherwise noted, these limits are over the operating free-air temperature
range.
3. Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground.
4. Typical values are at VCC=3.3V, TA = +25˚C ambient.
5. This parameter is specified but not tested.
6. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample
and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of
a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter
tests, IOS tests should be performed last.
7. Per TTL driven input; all other inputs at VCC or GND.
2
CY74FCT163827
Electrical Characteristics For Balanced Drive Devices Over the Operating Range VCC=2.7V to 3.6V
Parameter
Test Conditions
Typ.[4]
Max.
Unit
IODL
Output LOW Dynamic Current
VCC=3.3V, VIN=VIH
or VIL, VOUT=1.5V
45
180
mA
IODH
Output HIGH Dynamic Current[6]
VCC=3.3V, VIN=VIH
or VIL, VOUT=1.5V
–45
–180
mA
VOH
Output HIGH Voltage
VCC=Min., IOH= –0.1 mA
VOL
Description
[6]
Output LOW Voltage
Min.
VCC–0.2
V
VCC=Min., IOH= –8 mA
2.4[8]
3.0
VCC=3.0V, IOH= –24 mA
2.0
3.0
VCC=Min., IOL= 0.1mA
V
V
0.2
VCC=Min., IOL= 24 mA
0.3
V
0.55
Capacitance[5](TA = +25˚C, f = 1.0 MHz)
Parameter
Description
Test Conditions
Typ.[4]
Max.
Unit
CIN
Input Capacitance
VIN = 0V
4.5
6.0
pF
COUT
Output Capacitance
VOUT = 0V
5.5
8.0
pF
Note:
8. VOH=VCC–0.6V at rated current.
Power Supply Characteristics
Parameter
Description
Test Conditions
Typ.[4]
Max.
Unit
ICCD
Dynamic Power Supply
Current[9]
VCC=Max., One Input Toggling, VIN=VCC or
50% Duty Cycle,
VIN=GND
Outputs Open, OE=GND
50
75
µA/MHz
IC
Total Power Supply
Current[10]
VCC=Max., f1=10 MHz, 50%
VIN=VCC or
Duty Cycle, Outputs Open, One VIN=GND
Bit Toggling, OE=GND
VIN=VCC–0.6V or
VIN=GND
0.5
0.8
mA
0.5
0.8
mA
VIN=VCC or
VCC=Max., f1=2.5 MHz, 50%
Duty Cycle, Outputs Open, Six- VIN=GND
teen Bits Toggling, OE=GND
VIN=VCC–0.6V or
VIN=GND
2.0
3.0[11]
mA
2.0
3.3[11]
mA
3
CY74FCT163827
Switching Characteristics Over the Operating Range VCC=3.0V to 3.6V[12,13]
CY74FCT163827A
CY74FCT163827C
Description
Min.
Max.
Min.
Max.
Unit
Fig. No.[14]
tPLH
tPHL
Propagation Delay Data to
Output
1.5
4.8
1.5
4.1
ns
1, 3
tPZH
tPZL
Output Enable Time
1.5
6.2
1.5
5.8
ns
1, 7, 8
tPHZ
tPLZ
Output Disable Time
1.5
5.6
1.5
5.2
ns
1, 7, 8
tSK(O)
Output Skew[15]
0.5
ns
—
Parameter
0.5
Notes:
9. This parameter is not directly testable, but is derived for use in Total Power Supply calculations.
10. IC
= IQUIESCENT + IINPUTS + IDYNAMIC
IC
= ICC+∆ICCDHNT+ICCD(f0/2 + f1N1)
ICC = Quiescent Current with CMOS input levels
∆ICC = Power Supply Current for a TTL HIGH input (VIN=3.4V)
DH = Duty Cycle for TTL inputs HIGH
NT = Number of TTL inputs at DH
ICCD = Dynamic Current caused by an input transition pair (HLH or LHL)
= Clock frequency for registered devices, otherwise zero
f0
= Input signal frequency
f1
N1 = Number of inputs changing at f1
All currents are in milliamps and all frequencies are in megahertz.
11. Values for these conditions are examples of the ICC formula. These limits are specified but not tested.
12. Minimum limits are guaranteed but not tested on Propagation Delays.
13. For VCC =2.7, propagation delay, output enable and output disable times should be degraded by 20%.
14. See “Parameter Measurement Information” in the General Information section.
15. Skew between any two outputs of the same package switching in the same direction. This parameter is ensured by design.
Ordering Information CY74FCT163827
Speed
(ns)
4.1
4.8
Ordering Code
Package
Name
Package Type
CY74FCT163827CPACT
Z56
56-Lead (240-Mil) TSSOP
CY74FCT163827CPVC/PVCT
O56
56-Lead (300-Mil) SSOP
CY74FCT163827APVC/PVCT
O56
56-Lead (300-Mil) SSOP
4
Operating
Range
Commercial
Commercial
CY74FCT163827
Package Diagrams
56-Lead Shrunk Small Outline Package O56
56-Lead Thin Shrunk Small Outline Package Z56
5
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  2000, Texas Instruments Incorporated
Similar pages