Cypress CY7C1327F-225BGC 4-mb (256k x 18) pipelined sync sram Datasheet

CY7C1327F
4-Mb (256K x 18) Pipelined Sync SRAM
Functional Description[1]
Features
• Registered inputs and outputs for pipelined operation
• 256K ×18 common I/O architecture
• 3.3V core power supply
• 3.3V / 2.5V I/O operation
• Fast clock-to-output times
— 2.6 ns (for 250-MHz device)
— 2.6 ns (for 225-MHz device)
— 2.8 ns (for 200-MHz device)
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
— 3.5 ns (for 166-MHz device)
— 4.0 ns (for 133-MHz device)
— 4.5 ns (for 100-MHz device)
• Provide high-performance 3-1-1-1 access rate
• User-selectable burst counter supporting Intel
Pentium interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed writes
• Asynchronous output enable
• Offered in JEDEC-standard 100-pin TQFP and 119 Ball
BGA packages.
• “ZZ” Sleep Mode Option
The CY7C1327F SRAM integrates 262,144 x 18 SRAM cells
with advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE1), depth-expansion Chip Enables (CE2 and CE3), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables
(BW[A:B], and BWE), and Global Write (GW). Asynchronous
inputs include the Output Enable (OE) and the ZZ pin.
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to two bytes wide as
controlled by the byte write control inputs. GW when active
LOW causes all bytes to be written.
The CY7C1327F operates from a +3.3V core power supply
while all outputs also operate with a +3.3V or a +2.5V supply.
All
inputs
and
outputs
are
JEDEC-standard
JESD8-5-compatible.
Logic Block Diagram
A0, A1, A
ADDRESS
REGISTER
2
MODE
A[1:0]
BURST Q1
COUNTER AND
LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BWB
DQB,DQPB
WRITE DRIVER
DQB,DQPB
WRITE REGISTER
MEMORY
ARRAY
BWA
SENSE
AMPS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
DQA,DQPA
WRITE DRIVER
DQA,DQPA
WRITE REGISTER
DQs
DQPA
DQPB
E
BWE
GW
CE1
CE2
CE3
ENABLE
REGISTER
INPUT
REGISTERS
PIPELINED
ENABLE
OE
ZZ
SLEEP
CONTROL
1
Note:
1. For best–practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com
Cypress Semiconductor Corporation
Document #: 38-05216 Rev. *B
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised December 12, 2003
CY7C1327F
Selection Guide
250 MHz
225 MHz
200 MHz
166 MHz
133 MHz
100 MHz
Unit
Maximum Access Time
2.6
2.6
2.8
3.5
4.0
4.5
ns
Maximum Operating Current
325
290
265
240
225
205
mA
Maximum CMOS Standby
Current
40
40
40
40
40
40
mA
Shaded areas contain advance information. Please contact your local Cypress sales representative for availability of these parts.
NC
NC
NC
BYTE B
VDDQ
VSS
NC
NC
DQB
DQB
VSS
VDDQ
DQB
DQB
NC
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
100-pin TQFP
CY7C1327F
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
NC
VSS
VDDQ
NC
NC
NC
BYTE A
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
VSS
DQB
DQB
VDDQ
VSS
DQB
DQB
DQPB
NC
VSS
VDDQ
NC
NC
NC
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
Pin Configurations
Document #: 38-05216 Rev. *B
Page 2 of 17
CY7C1327F
Pin Configurations
119-ball BGA
1
2
3
4
5
6
7
A
VDDQ
A
A
ADSP
A
A
VDDQ
B
C
NC
NC
CE2
A
A
A
ADSC
VDD
A
A
CE3
A
NC
NC
D
DQB
NC
VSS
NC
VSS
DQPA
NC
E
F
NC
VDDQ
DQB
NC
VSS
VSS
VSS
VSS
NC
DQA
DQA
VDDQ
G
H
J
NC
DQB
VDDQ
DQB
NC
VDD
BWB
VSS
NC
CE1
OE
ADV
GW
VDD
Vss
VSS
NC
NC
DQA
VDD
DQA
NC
VDDQ
K
NC
DQB
VSS
CLK
VSS
NC
DQA
L
DQB
NC
Vss
NC
BWA
DQA
NC
M
N
VDDQ
DQB
DQB
NC
VSS
VSS
BWE
A1
VSS
VSS
NC
DQA
VDDQ
NC
P
NC
DQPB
VSS
A0
VSS
NC
DQA
R
T
NC
NC
A
MODE
VDD
A
A
NC
NC
A
A
A
NC
ZZ
U
VDDQ
NC
NC
NC
NC
NC
VDDQ
Document #: 38-05216 Rev. *B
Page 3 of 17
CY7C1327F
Pin Definitions
Name
TQFP
BGA
A0, A1, A
37,36,
32,33,34,
35,44,45,
46,47,48,
49,50,80,
81,82,99,
100
P4,N4,A2,
C2,R2,T2,
A3,B3,C3,
T3,A5,B5,
C5,T5,A6,
C6,R6,T6
InputAddress Inputs used to select one of the 256K address locations. Sampled
Synchronous at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1,
CE2, and CE3 are sampled active. A1, A0 feed the 2-bit counter.
BWA,BWB
93,94
L5,G3
InputByte Write Select Inputs, active LOW. Qualified with BWE to conduct
Synchronous byte writes to the SRAM. Sampled on the rising edge of CLK.
GW
88
H4
InputGlobal Write Enable Input, active LOW. When asserted LOW on the
Synchronous rising edge of CLK, a global write is conducted (ALL bytes are written,
regardless of the values on BW[A:B] and BWE).
BWE
87
M4
InputByte Write Enable Input, active LOW. Sampled on the rising edge of
Synchronous CLK. This signal must be asserted LOW to conduct a byte write.
CLK
89
K4
98
E4
CE2
97
B2
CE3
92
B6
OE
86
F4
ADV
83
G4
InputAdvance Input signal, sampled on the rising edge of CLK, active
Synchronous LOW. When asserted, it automatically increments the address in a burst
cycle.
84
A4
InputAddress Strobe from Processor, sampled on the rising edge of CLK,
Synchronous active LOW. When asserted LOW, A is captured in the address registers.
A1, A0 are also loaded into the burst counter. When ADSP and ADSC are
both asserted, only ADSP is recognized. ASDP is ignored when CE1 is
deasserted HIGH.
ZZ
64
T7
InputZZ “sleep” Input, active HIGH. This input, when High places the device
Asynchronous in a non-time-critical “sleep” condition with data integrity preserved. For
normal operation, this pin has to be LOW or left floating. ZZ pin has an
internal pull-down.
ADSC
85
B4
InputAddress Strobe from Controller, sampled on the rising edge of CLK,
Synchronous active LOW. When asserted LOW, A is captured in the address registers.
A1, A0 are also loaded into the burst counter. When ADSP and ADSC are
both asserted, only ADSP is recognized.
DQA,
DQB
58,59,62,
63,68,69,
72,73
8,9,12,13,
18,19,22,
23
74,24
F6,H6,L6,
N6,E7,G7,
K7,P7
D1,H1,L1,
N1,E2,G2,
K2,M2,
D6,P2
I/OBidirectional Data I/O lines. As inputs, they feed into an on-chip data
Synchronous register that is triggered by the rising edge of CLK. As outputs, they deliver
the data contained in the memory location specified by “A” during the
previous clock rise of the read cycle. The direction of the pins is controlled
by OE. When OE is asserted LOW, the pins behave as outputs. When
HIGH, DQs and DQP[A:B] are placed in a three-state condition.
CE1
ADSP
DQPA,
DQPB
Document #: 38-05216 Rev. *B
I/O
InputClock
Description
Clock Input. Used to capture all synchronous inputs to the device. Also
used to increment the burst counter when ADV is asserted LOW, during
a burst operation.
InputChip Enable 1 Input, active LOW. Sampled on the rising edge of CLK.
Synchronous Used in conjunction with CE2 and CE3 to select/deselect the device. ADSP
is ignored if CE1 is HIGH.
InputChip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK.
Synchronous Used in conjunction with CE1 and CE3 to select/deselect the device.
InputChip Enable 3 Input, active LOW. Sampled on the rising edge of CLK.
Synchronous Used in conjunction with CE1 and CE2 to select/deselect the device. Not
connected for BGA. Where referenced, CE3 is assumed active throughout
this document for BGA.
InputOutput Enable, asynchronous input, active LOW. Controls the
Asynchronous direction of the I/O pins. When LOW, the I/O pins behave as outputs. When
deasserted HIGH, I/O pins are three-stated, and act as input data pins.
OE is masked during the first clock of a read cycle when emerging from a
deselected state.
Page 4 of 17
CY7C1327F
Pin Definitions (continued)
Name
TQFP
BGA
VDD
15,41,65, J2,C4,J4,
91
R4,J6
VSS
5,10,17,
21,26,40,
55,60,67,
71,76,90
VDDQ
4,11,20, A1,F1,J1,
27,54,61, M1,U1,A7,
70,77
F7,J7,M7,
U7
MODE
NC
D3,E3,F3,
H3,K3,L3,
M3,N3,P3,
D5,E5,F5,
G5,H5,K5,
M5,N5,P5
31
R3
1,2,3,6,7,
14,16,25,
28,29,30,
38,39,42,
43,51,52,
53,56,57,
66,75,78,
79,95,96
B1,C1,E1,
G1,K1,P1,
R1,T1,D2,
F2,H2,L2,
N2,U2,J3,
U3,D4,L4,
T4,U4,J5,
U5,E6,G6,
K6,M6,P6,
U6,B7,C7,
D7,H7,L7,
N7,R5,R7
I/O
Description
Power Supply Power supply inputs to the core of the device.
Ground
I/O Ground
InputStatic
Ground for the device.
Ground for the I/O circuitry.
Selects Burst Order. When tied to GND selects linear burst sequence.
When tied to VDD or left floating selects interleaved burst sequence. This
is a strap pin and should remain static during device operation. Mode Pin
has an internal pull-up.
No Connects. Not internally connected to the die
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock.
The CY7C1327F supports secondary cache in systems
utilizing either a linear or interleaved burst sequence. The
interleaved burst order supports Pentium and i486
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is user
selectable, and is determined by sampling the MODE input.
Accesses can be initiated with either the Processor Address
Strobe (ADSP) or the Controller Address Strobe (ADSC).
Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
Byte Write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BW[A:B]) inputs. A Global Write
Enable (GW) overrides all Byte Write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self-timed Write circuitry.
Three synchronous Chip Selects (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output three-state control. ADSP is ignored if
CE1 is HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE1, CE2, CE3 are all asserted active, and (3) the Write
signals (GW, BWE) are all deserted HIGH. ADSP is ignored if
CE1 is HIGH. The address presented to the address inputs (A)
is stored into the address advancement logic and the Address
Register while being presented to the memory array. The
corresponding data is allowed to propagate to the input of the
Output Registers. At the rising edge of the next clock the data
is allowed to propagate through the output register and onto
the data bus within tco if OE is active LOW. The only exception
occurs when the SRAM is emerging from a deselected state
to a selected state, its outputs are always three-stated during
the first cycle of the access. After the first cycle of the access,
the outputs are controlled by the OE signal. Consecutive
single Read cycles are supported. Once the SRAM is
deselected at clock rise by the chip select and either ADSP or
ADSC signals, its output will three-state immediately.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions
are satisfied at clock rise: (1) ADSP is asserted LOW, and
(2) CE1, CE2, CE3 are all asserted active. The address
presented to A is loaded into the address register and the
address advancement logic while being delivered to the
memory array. The Write signals (GW, BWE, and BW[A:B]) and
ADV inputs are ignored during this first cycle.
ADSP-triggered Write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
Document #: 38-05216 Rev. *B
Page 5 of 17
CY7C1327F
data presented to the DQ inputs is written into the corresponding address location in the memory array. If GW is HIGH,
then the Write operation is controlled by BWE and BW[A:B]
signals. The CY7C1327F provides Byte Write capability that is
described in the Write Cycle Descriptions table. Asserting the
Byte Write Enable input (BWE) with the selected Byte Write
(BW[A:B]) input, will selectively write to only the desired bytes.
Bytes not selected during a Byte Write operation will remain
unaltered. A synchronous self-timed Write mechanism has
been provided to simplify the Write operations.
sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst
sequence is designed to support processors that follow a
linear burst sequence. The burst sequence is user selectable
through the MODE input.
Because the CY7C1327F is a common I/O device, the Output
Enable (OE) must be deserted HIGH before presenting data
to the DQ inputs. Doing so will three-state the output drivers.
As a safety precaution, DQs are automatically three-stated
whenever a Write cycle is detected, regardless of the state of
OE.
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, CE3, ADSP, and ADSC must
remain inactive for the duration of tZZREC after the ZZ input
returns LOW.
Single Write Accesses Initiated by ADSC
ADSC Write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is
deserted HIGH, (3) CE1, CE2, CE3 are all asserted active, and
(4) the appropriate combination of the Write inputs (GW, BWE,
and BW[A:B]) are asserted active to conduct a Write to the
desired byte(s). ADSC-triggered Write accesses require a
single clock cycle to complete. The address presented to A is
loaded into the address register and the address
advancement logic while being delivered to the memory array.
The ADV input is ignored during this cycle. If a global Write is
conducted, the data presented to DQ is written into the corresponding address location in the memory core. If a Byte Write
is conducted, only the selected bytes are written. Bytes not
selected during a Byte Write operation will remain unaltered.
A synchronous self-timed Write mechanism has been
provided to simplify the Write operations.
Because the CY7C1327F is a common I/O device, the Output
Enable (OE) must be deserted HIGH before presenting data
to the DQ inputs. Doing so will three-state the output drivers.
As a safety precaution, DQs are automatically three-stated
whenever a Write cycle is detected, regardless of the state of
OE.
Burst Sequences
The CY7C1327F provides a two-bit wraparound counter, fed
by A1, A0, that implements either an interleaved or linear burst
Asserting ADV LOW at clock rise will automatically increment
the burst counter to the next address in the burst sequence.
Both Read and Write burst operations are supported.
Sleep Mode
Interleaved Burst Address Table (MODE =
Floating or VDD)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min.
Max.
Unit
IDDZZ
Snooze mode standby current
ZZ > VDD – 0.2V
40
mA
tZZS
Device operation to ZZ
ZZ > VDD – 0.2V
2tCYC
ns
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ active to snooze current
This parameter is sampled
tRZZI
ZZ Inactive to exit snooze current
This parameter is sampled
Document #: 38-05216 Rev. *B
2tCYC
ns
2tCYC
0
ns
ns
Page 6 of 17
CY7C1327F
Truth Table[ 2, 3, 4, 5, 6]
Next Cycle
Add. Used
ZZ
CE2
X
CE3
X
ADSP
X
ADSC
L
ADV
X
OE
X
X
H
L
X
X
X
DQ
Unselected
None
L
CE1
H
Unselected
None
L
L
Unselected
None
L
L
L
X
L
X
X
X
three-state X
Unselected
None
L
L
X
H
H
L
X
X
three-state X
Unselected
None
L
L
L
X
H
L
X
X
three-state X
Begin Read
External
L
L
H
L
L
X
X
X
three-state X
Begin Read
External
WRITE
three-state X
three-state X
L
L
H
L
H
L
X
X
three-state Read
Continue Read Next
L
X
X
X
H
H
L
H
three-state Read
Continue Read Next
L
X
X
X
H
H
L
L
DQ
Continue Read Next
L
H
X
X
X
H
L
H
three-state Read
Continue Read Next
L
H
X
X
X
H
L
L
DQ
Suspend Read Current
L
X
X
X
H
H
H
H
three-state Read
Suspend Read Current
L
X
X
X
H
H
H
L
DQ
Suspend Read Current
L
H
X
X
X
H
H
H
three-state Read
Suspend Read Current
L
H
X
X
X
H
H
L
DQ
Begin Write
Current
L
X
X
X
H
H
H
X
three-state Write
Begin Write
Current
L
H
X
X
X
H
H
X
three-state Write
Begin Write
External
L
L
H
L
H
H
X
X
three-state Write
Read
Read
Read
Read
Continue Write Next
L
X
X
X
H
H
H
X
three-state Write
Continue Write Next
L
H
X
X
X
H
H
X
three-state Write
Suspend Write Current
L
X
X
X
H
H
H
X
three-state Write
Suspend Write Current
L
H
X
X
X
H
H
X
three-state Write
ZZ “Sleep”
H
X
X
X
X
X
X
X
three-state X
None
Truth Table for Read/Write[2]
Function
Read
GW
H
BWE
H
BWB
X
BWA
X
Read
H
L
H
H
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
H
L
H
L
H
L
L
H
Write Bytes B, A
H
L
L
L
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals (BWA, BWB) and BWE = L or GW = L. WRITE = H when all Byte write enable signals (BWA, BWB),
BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW[A: B]. Writes may occur only on subsequent clocks
after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to three-state. OE is
a don't care for the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are three-state when OE
is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document #: 38-05216 Rev. *B
Page 7 of 17
CY7C1327F
Maximum Ratings
Current into Outputs (LOW)......................................... 20 mA
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V
DC Voltage Applied to Outputs
in three-state ....................................... –0.5V to VDDQ + 0.5V
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current.................................................... > 200 mA
Operating Range
Ambient
Range
Temperature
VDD
VDDQ
Commercial 0°C to +70°C 3.3V –5%/+10% 2.5V –5%
to VDD
Industrial
–40°C to +85°C
DC Input Voltage....................................–0.5V to VDD + 0.5V
Electrical Characteristics Over the Operating Range [7, 8]
Parameter
Description
Test Conditions
Min.
Max.
Unit
VDD
Power Supply Voltage
3.135
3.6
V
VDDQ
I/O Supply Voltage
2.375
VDD
V
VOH
Output HIGH Voltage
VOL
VIH
VIL
IX
Output LOW Voltage
Input HIGH
Input LOW
Voltage[7]
Voltage[7]
Input Load Current
except ZZ and MODE
VDDQ = 3.3V, VDD = Min., IOH = –4.0 mA
2.4
V
VDDQ = 2.5V, VDD = Min., IOH = –2.0 mA
2.0
V
VDDQ = 3.3V, VDD = Min., IOL = 8.0 mA
0.4
V
VDDQ = 2.5V, VDD = Min., IOL = 2.0 mA
0.4
V
VDDQ = 3.3V
2.0
VDD + 0.3V
V
VDDQ = 2.5V
1.7
VDD + 0.3V
V
VDDQ = 3.3V
–0.3
0.8
V
VDDQ = 2.5V
–0.3
0.7
V
–5
5
µA
5
µA
GND ≤ VI ≤ VDDQ
Input = VDD
Input Current of ZZ
Input = VSS
30
IOZ
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
IDD
VDD Operating Supply
Current
ISB1
ISB2
Automatic CE
Power-down
Current—TTL Inputs
VDD = Max, Device
Deselected, VIN ≥ VIH or
VIN ≤ VIL
f = fMAX = 1/tCYC
Automatic CE
VDD = Max, Device
Power-down
Deselected, VIN ≤ 0.3V or
Current—CMOS Inputs VIN > VDDQ – 0.3V, f = 0
µA
–5
Input = VDD
VDD = Max.,
IOUT = 0 mA,
f = fMAX =
1/tCYC
µA
–30
Input Current of MODE Input = VSS
µA
5
µA
4-ns cycle,250MHz
325
mA
4.4-ns cycle,225MHz
290
mA
5-ns cycle,200MHz
265
mA
–5
6-ns cycle,166MHz
240
mA
7.5-ns cycle,133MHz
225
mA
10-ns cycle,100MHz
205
mA
4-ns cycle,250MHz
120
mA
4.4-ns cycle,225MHz
115
mA
5-ns cycle,200MHz
110
mA
6-ns cycle,166MHz
100
mA
7.5-ns cycle,133MHz
90
mA
10-ns cycle,100MHz
80
mA
All speeds
40
mA
Shaded areas contain advance information.
Notes:
7. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > -2V (Pulse width less than tCYC/2).
8. TPower-up: Assumes a linear ramp from 0v to VDD(min.) within 200ms. During this time VIH < VDD and VDDQ < VDD.
Document #: 38-05216 Rev. *B
Page 8 of 17
CY7C1327F
Electrical Characteristics Over the Operating Range (continued)[7, 8]
Parameter
ISB3
Description
Test Conditions
Automatic CE
VDD = Max, Device
Power-down
Deselected, or VIN ≤ 0.3V
Current—CMOS Inputs or VIN > VDDQ – 0.3V
f = fMAX = 1/tCYC
ISB4
Max.
Unit
4-ns cycle,250MHz
105
mA
4.4-ns cycle,225MHz
100
mA
5-ns cycle,200MHz
95
mA
6-ns cycle,166MHz
85
mA
7.5-ns cycle,133MHz
75
mA
10-ns cycle,100MHz
65
mA
All speeds
45
mA
VDD = Max, Device
Deselected, VIN ≥ VIH or
VIN ≤ VIL, f = 0
Automatic CE
Power-down
Current—TTL Inputs
Min.
Thermal Resistance[9]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
Test conditions follow standard test
methods and procedures for measuring
thermal impedance, per EIA / JESD51.
TQFP
Package
BGA
Package
Unit
41.83
47.63
°C/W
9.99
11.71
°C/W
Capacitance[9]
Parameter
Description
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CI/O
Input/Output Capacitance
TQFP
Package
Test Conditions
TA = 25°C, f = 1 MHz,
VDD = 3.3V.
VDDQ = 3.3V
BGA
Package
Unit
5
5
pF
5
5
pF
5
7
pF
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
OUTPUT
RL = 50Ω
Z0 = 50Ω
GND
5 pF
R = 351Ω
INCLUDING
JIG AND
SCOPE
10%
90%
10%
90%
≤ 1ns
≤ 1ns
VL = 1.5V
(a)
ALL INPUT PULSES
VDD
(c)
(b)
2.5V I/O Test Load
R = 1667Ω
2.5V
OUTPUT
OUTPUT
RL = 50Ω
Z0 = 50Ω
GND
5 pF
R =1538Ω
VL = 1.25V
(a)
ALL INPUT PULSES
VDD
INCLUDING
JIG AND
SCOPE
(b)
10%
90%
10%
90%
≤ 1ns
≤ 1ns
(c)
Notes:
9. Tested initially and after any design or process change that may affect these parameters
Document #: 38-05216 Rev. *B
Page 9 of 17
CY7C1327F
Switching Characteristics Over the Operating Range[14, 15]
250 MHz
Parameter
tPOWER
tDOH
Data Output Hold After CLK
Rise
tCLZ
Clock to Low-Z[11, 12, 13]
tCHZ
Clock to High-Z[11, 12, 13]
tOEV
OE LOW to Output Valid
OE LOW to Output Low-Z[11,
tOEHZ
200 MHz
166 MHz
133 MHz
100 MHz
Min. Max Min. Max Min. Max Min. Max Min. Max Min. Max Unit
Description
VDD(Typical) to the first[10]
Clock
tCYC
Clock Cycle Time
Clock HIGH
tCH
Clock LOW
tCL
Output Times
Data Output Valid After CLK
tCO
Rise
tOELZ
225 MHz
1
1
1
1
1
1
ms
4.0
1.7
1.7
4.4
2.0
2.0
5.0
2.0
2.0
6.0
2.5
2.5
7.5
3.0
3.0
10
3.5
3.5
ns
ns
ns
2.6
1.0
2.6
1.0
0
12, 13]
[11,
2.6
OE HIGH to Output High-Z
2.6
2.8
3.5
ns
4.5
4.5
0
4.5
0
4.0
ns
ns
0
4.0
3.5
0
4.5
2.0
0
3.5
2.8
0
4.0
2.0
0
2.8
2.6
0
3.5
2.0
0
2.6
2.6
0
12, 13]
1.0
0
2.6
2.8
ns
ns
ns
4.5
ns
Set-up Times
tAS
Address Set-up Before CLK
Rise
0.8
1.2
1.2
1.5
1.5
1.5
ns
tADS
ADSC, ADSP Set-up Before
CLK Rise
ADV Set-up Before CLK Rise
GW, BWE, BW[A:B] Set-up
Before CLK Rise
0.8
1.2
1.2
1.5
1.5
1.5
ns
0.8
1.2
1.2
1.5
1.5
1.5
ns
0.8
1.2
1.2
1.5
1.5
1.5
ns
tDS
Data Input Set-up Before CLK
Rise
0.8
1.2
1.2
1.5
1.5
1.5
ns
tCES
Chip Enable Set-Up Before
CLK Rise
0.8
1.2
1.2
1.5
1.5
1.5
ns
tADVS
tWES
Hold Times
Address Hold After CLK Rise
0.4
0.5
0.5
0.5
0.5
0.5
ns
tADH
ADSP , ADSC Hold After CLK
Rise
0.4
0.5
0.5
0.5
0.5
0.5
ns
tADVH
ADV Hold After CLK Rise
GW,BWE, BW[A:B] Hold After
CLK Rise
Data Input Hold After CLK
Rise
0.4
0.5
0.5
0.5
0.5
0.5
ns
0.4
0.5
0.5
0.5
0.5
0.5
ns
0.4
0.5
0.5
0.5
0.5
0.5
ns
Chip Enable Hold After CLK
Rise
0.4
0.5
0.5
0.5
0.5
0.5
ns
tAH
tWEH
tDH
tCEH
Shaded areas contain advance information.
Notes:
10. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation
can be initiated.
11. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
12. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
13. This parameter is sampled and not 100% tested.
14. Timing references level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V on all data sheets.
15. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05216 Rev. *B
Page 10 of 17
CY7C1327F
Switching Waveforms
Read Cycle Timing[16]
t CYC
CLK
t
CH
t
ADS
t
CL
t
ADH
ADSP
tADS
tADH
ADSC
tAS
ADDRESS
tAH
A1
A2
tWES
A3
Burst continued with
new base address
tWEH
GW, BWE,
BW[A:B]
Deselect
cycle
tCES tCEH
CE
tADVS tADVH
ADV
ADV
suspends
burst.
OE
t OEHZ
t CLZ
Data Out (Q)
High-Z
Q(A1)
tOEV
tCO
t OELZ
tDOH
Q(A2)
t CHZ
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
t CO
Single READ
BURST READ
DON’T CARE
Burst wraps around
to its initial state
UNDEFINED
Notes:
16. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
17. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A:B] LOW.
Document #: 38-05216 Rev. *B
Page 11 of 17
CY7C1327F
Switching Waveforms (continued)
Write Cycle Timing[16, 17]
t CYC
CLK
tCH
tADS
tCL
tADH
ADSP
tADS
ADSC extends burst
tADH
tADS
tADH
ADSC
tAS
tAH
A1
ADDRESS
A2
A3
Byte write signals are
ignored for first cycle when
ADSP initiates burst
tWES tWEH
BWE,
BW[A :B]
tWES tWEH
GW
tCES
tCEH
CE
t
t
ADVS ADVH
ADV
ADV suspends burst
OE
tDS
Data In (D)
High-Z
t
OEHZ
tDH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
DON’T CARE
Document #: 38-05216 Rev. *B
Extended BURST WRITE
UNDEFINED
Page 12 of 17
CY7C1327F
Switching Waveforms (continued)
Read/Write Cycle Timing[16, 18, 19]
tCYC
CLK
tCL
tCH
tADS
tADH
tAS
tAH
ADSP
ADSC
ADDRESS
A1
A2
A3
A4
A5
A6
D(A5)
D(A6)
tWES tWEH
BWE,
BW[A:B]
tCES
tCEH
CE
ADV
OE
tDS
tCO
Data In (D)
tOELZ
High-Z
tCLZ
Data Out (Q)
tDH
High-Z
Q(A1)
Back-to-Back READs
tOEHZ
D(A3)
Q(A2)
Q(A4)
Single WRITE
Q(A4+1)
Q(A4+2)
BURST READ
DON’T CARE
Q(A4+3)
Back-to-Back
WRITEs
UNDEFINED
Notes:
18. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC.
19. GW is HIGH.
Document #: 38-05216 Rev. *B
Page 13 of 17
CY7C1327F
Switching Waveforms (continued)
ZZ Mode Timing [20, 21]
CLK
t
ZZ
I
t
t
ZZ
ZZREC
ZZI
SUPPLY
I
DDZZ
t RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Ordering Information
Speed
(MHz)
250
Ordering Code
CY7C1327F-250AC
CY7C1327F-250BGC
CY7C1327F-250AI
CY7C1327F-250BGI
225
CY7C1327F-225AC
CY7C1327F-225BGC
CY7C1327F-225AI
CY7C1327F-225BGI
200
CY7C1327F-200AC
CY7C1327F-200BGC
CY7C1327F-200AI
CY7C1327F-200BGI
166
CY7C1327F-166AC
CY7C1327F-166BGC
CY7C1327F-166AI
CY7C1327F-166BGI
133
CY7C1327F-133AC
CY7C1327F-133BGC
CY7C1327F-133AI
CY7C1327F-133BGI
Package
Name
Package Type
Operating
Range
A101
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Commercial
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
A101
BG119
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Industrial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Commercial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Industrial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Commercial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
Industrial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pact (14 x 20 x 1.4mm)
Commercial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pact (14 x 20 x 1.4mm)
Industrial
119-Ball BGA (14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack(14 x 20 x 1.4mm)
Commercial
119-Ball BGA(14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack(14 x 20 x 1.4mm)
Industrial
119-Ball BGA(14 x 22 x 2.4mm)
Notes:
20. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
21. DQs are in high-Z when exiting ZZ sleep mode.
Document #: 38-05216 Rev. *B
Page 14 of 17
CY7C1327F
Ordering Information (continued)
Speed
(MHz)
100
Ordering Code
CY7C1327F-100AC
CY7C1327F-100BGC
CY7C1327F-100AI
CY7C1327F-100BGI
Package
Name
Package Type
Operating
Range
A101
100-Lead Thin Quad Flat Pack(14 x 20 x 1.4mm)
Commercial
BG119
A101
BG119
119-Ball BGA(14 x 22 x 2.4mm)
100-Lead Thin Quad Flat Pack(14 x 20 x 1.4mm)
Industrial
119-Ball BGA(14 x 22 x 2.4mm)
Shaded areas contain advance information. Please contact your local Cypress sales representative for availability of these parts.
Package Diagrams
100-pin Thin Plastic Quad Flat Pack (14 x 20 x 1.4mm) A101
51-85050*A
Document #: 38-05216 Rev. *B
Page 15 of 17
CY7C1327F
Package Diagrams (continued)
119-lead BGA (14 x 22 x 2.4 mm) BG119
51-85115-*A
i486 is a trademark, and Intel and Pentium are registered trademarks, of Intel Corporation. PowerPC is a registered trademark
of IBM Corporation. All product and company names mentioned in this document may be trademarks of their respective holders.
Document #: 38-05216 Rev. *B
Page 16 of 17
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY7C1327F
Document History Page
Document Title: CY7C1327F 4-Mb (256K x 18) Pipelined Sync SRAM
Document Number: 38-05216
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
119823
01/06/03
HGK
New Data Sheet
*A
123849
01/18/03
AJH
Added power up requirements to AC test loads and waveforms information
*B
200660
See ECN
SWI
Final Data Sheet
Document #: 38-05216 Rev. *B
Page 17 of 17
Similar pages