Cypress CY7C1361C-117BGI 9-mbit (256k x 36/512k x 18) flow-through sram Datasheet

CY7C1361C
CY7C1363C
PRELIMINARY
9-Mbit (256K x 36/512K x 18) Flow-Through SRAM
Functional Description[1]
Features
• Supports 133-MHz bus operations
The CY7C1361C/CY7C1363C is a 3.3V, 256K x 36 and 512K x
18 Synchronous Flowthrough SRAMs, respectively designed
to interface with high-speed microprocessors with minimum
glue logic. Maximum access delay from clock rise is 6.5 ns
(133-MHz version). A 2-bit on-chip counter captures the first
address in a burst and increments the address automatically
for the rest of the burst access. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE1), depth-expansion Chip Enables (CE2 and CE3[2]), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables (BWx,
and BWE), and Global Write (GW). Asynchronous inputs
include the Output Enable (OE) and the ZZ pin.
• 256K × 36/512K × 18 common I/O
• 3.3V –5% and +10% core power supply (VDD)
• 2.5V or 3.3V I/O supply (VDDQ)
• Fast clock-to-output times
— 6.5 ns (133-MHz version)
— 7.5 ns (117-MHz version)
— 8.5 ns (100-MHz version)
• Provide high-performance 2-1-1-1 access rate
• User-selectable burst counter supporting Intel
Pentium interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed write
• Asynchronous output enable
• Available in Lead-Free 100 TQFP,119 BGA and 165 fBGA
packages Both 2 and 3 Chip Enable Options for TQFP
• IEEE 1149.1 compatible JTAG Boundary Scan for BGA
and fBGA packages
•“ZZ” Sleep Mode option
The CY7C1361C/CY7C1363C allows either interleaved or
linear burst sequences, selected by the MODE input pin. A
HIGH selects an interleaved burst sequence, while a LOW
selects a linear burst sequence. Burst accesses can be
initiated with the Processor Address Strobe (ADSP) or the
cache Controller Address Strobe (ADSC) inputs. Address
advancement is controlled by the Address Advancement
(ADV) input.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
The CY7C1361C/CY7C1363C operates from a +3.3V core
power supply while all outputs may operate with either a +2.5
or +3.3V supply. All inputs and outputs are JEDEC-standard
JESD8-5-compatible.
Selection Guide
133 MHz
117 MHz
100 MHz
Unit
Maximum Access Time
6.5
7.5
8.5
ns
Maximum Operating Current
250
220
180
mA
Maximum CMOS Standby Current
30
30
30
mA
Notes:
1. For best–practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
2. CE3 is for A version of TQFP ( 3 Chip Enable Option) and 165 fBGA package only. 119 BGA is offered only in 2 Chip Enable.
Cypress Semiconductor Corporation
Document #: 38-05541 Rev. *A
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised October 5, 2004
CY7C1361C
CY7C1363C
PRELIMINARY
Logic Block Diagram – CY7C1361C (256K x 36)
ADDRESS
REGISTER
A0, A1, A
A[1:0]
MODE
BURST Q1
COUNTER
AND LOGIC
Q0
CLR
ADV
CLK
ADSC
ADSP
DQD, DQPD
DQD, DQPD
BWD
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
DQC, DQPC
DQC, DQPC
BWC
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
DQB, DQPB
BWB
DQB, DQPB
BYTE
BYTE
WRITE REGISTER
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
BUFFERS
DQs
DQPA
DQPB
DQPC
DQPD
WRITE REGISTER
DQA, DQPA
BWA
BWE
DQA, DQPA
BYTE
BYTE
WRITE REGISTER
WRITE REGISTER
INPUT
REGISTERS
GW
ENABLE
REGISTER
CE1
CE2
CE3
OE
SLEEP
CONTROL
ZZ
1
Logic Block Diagram – CY7C1363C (512K x 18)
ADDRESS
REGISTER
A0,A1,A
A[1:0]
MODE
BURST Q1
COUNTER AND
LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BWB
BWA
DQB,DQPB
WRITE REGISTER
DQA,DQPA
WRITE REGISTER
DQB,DQPB
WRITE DRIVER
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
BUFFERS
DQs
DQPA
DQPB
DQA,DQPA
WRITE DRIVER
BWE
GW
CE1
CE2
CE3
ENABLE
REGISTER
INPUT
REGISTERS
OE
ZZ
Document #: 38-05541 Rev. *A
SLEEP
CONTROL
Page 2 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Configurations
NC
NC
NC
CY7C1363C
(512K x 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VDDQ
VSSQ
NC
NC
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS/DNU
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
VSSQ
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
A
A
A
A
A
A
A
A
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
CY7C1361C
(256K x 36)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
A
A
A
A
A
A
A
A
DQPC
DQC
DQC
VDDQ
VSSQ
DQC
DQC
DQC
DQC
VSSQ
VDDQ
DQC
DQC
VSS/DNU
VDD
NC
VSS
DQD
DQD
VDDQ
VSSQ
DQD
DQD
DQD
DQD
VSSQ
VDDQ
DQD
DQD
DQPD
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE1
CE2
BWD
BWC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
100-pin TQFP Pinout (3 Chip Enables) (A version)
Document #: 38-05541 Rev. *A
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
NC
VSSQ
VDDQ
NC
NC
NC
Page 3 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Configurations (continued)
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
MODE
A
A
A
A
A1
A0
Document #: 38-05541 Rev. *A
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
VDDQ
VSSQ
NC
NC
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS/DNU
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
VSSQ
VDDQ
NC
NC
NC
CY7C1363C
(512K x 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
NC
VSSQ
VDDQ
NC
NC
NC
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
CY7C1361C
(256K x 36)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DQPC
DQC
DQC
VDDQ
VSSQ
DQC
DQC
DQC
DQC
VSSQ
VDDQ
DQC
DQC
VSS/DNU
VDD
NC
VSS
DQD
DQD
VDDQ
VSSQ
DQD
DQD
DQD
DQD
VSSQ
VDDQ
DQD
DQD
DQPD
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
NC
NC
BWB
BWA
A
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE1
CE2
BWD
BWC
BWB
BWA
A
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
100-pin TQFP (2 Chip Enables) (AJ Version)
Page 4 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Configurations (continued)
119-ball BGA (2 Chip Enables with JTAG)
1
CY7C1361C (256K x 36)
3
4
5
A
A
ADSP
A
VDDQ
2
A
B
C
NC
NC
CE2
A
A
A
ADSC
VDD
A
A
A
A
NC
NC
D
E
DQC
DQC
DQPC
DQC
VSS
VSS
NC
CE1
VSS
VSS
DQPB
DQB
DQB
DQB
F
VDDQ
DQC
VSS
OE
VSS
DQB
VDDQ
G
H
J
K
DQC
DQC
VDDQ
DQD
DQC
DQC
VDD
DQD
BWC
VSS
NC
VSS
ADV
BWB
VSS
NC
VSS
DQB
DQB
VDD
DQA
DQB
DQB
VDDQ
DQA
BWA
VSS
DQA
DQA
DQA
VDDQ
VSS
DQA
DQA
GW
VDD
CLK
NC
6
A
7
VDDQ
L
DQD
DQD
M
VDDQ
DQD
BWD
VSS
N
DQD
DQD
VSS
BWE
A1
P
DQD
DQPD
VSS
A0
VSS
DQPA
DQA
R
NC
A
MODE
VDD
NC
A
NC
T
U
NC
VDDQ
NC
TMS
A
TDI
A
TCK
A
TDO
NC
NC
ZZ
VDDQ
CY7C1363C (512K x 18)
1
2
3
4
5
6
7
A
VDDQ
A
A
ADSP
A
A
VDDQ
B
NC
CE2
A
A
A
A
A
A
NC
NC
ADSC
VDD
A
C
D
DQB
NC
VSS
NC
VSS
DQPA
NC
E
NC
DQB
VSS
CE1
VSS
NC
DQA
OE
ADV
VSS
DQA
VDDQ
VSS
VSS
NC
DQA
VDD
DQA
NC
VDDQ
NC
DQA
BWA
VSS
DQA
NC
NC
VDDQ
NC
F
VDDQ
NC
VSS
G
H
J
NC
DQB
VDDQ
DQB
NC
VDD
BWB
VSS
NC
K
NC
DQB
VSS
L
M
DQB
VDDQ
NC
DQB
VSS
VSS
N
DQB
NC
VSS
BWE
A1
VSS
DQA
NC
P
NC
DQPB
VSS
A0
VSS
NC
DQA
R
T
U
NC
NC
VDDQ
A
A
TMS
MODE
A
TDI
VDD
NC
TCK
NC
A
TDO
A
A
NC
NC
ZZ
VDDQ
Document #: 38-05541 Rev. *A
GW
VDD
CLK
NC
NC
VSS
Page 5 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Configurations (continued)
165-ball fBGA (3 Chip Enable)
CY7C1361C (256K x 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC / 288M
A
CE1
BWC
BWB
CE3
BWE
ADSC
ADV
A
NC
R
NC
A
CE2
BWD
BWA
CLK
GW
OE
ADSP
A
NC / 144M
DQPC
DQC
NC
DQC
VDDQ
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
VSS
VDD
VDDQ
NC
DQB
DQPB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
DQB
DQB
DQC
NC
DQD
DQC
VSS
DQD
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQB
NC
DQA
DQB
ZZ
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQPD
DQD
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
DQPA
NC
NC / 72M
A
A
TDI
NC / 18M
A1
VSS
NC
TDO
A
A
A
A
MODE
NC / 36M
A
A
TMS
A0
TCK
A
A
A
A
CY7C1363C (512K x 18)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC / 288M
A
CE1
BWB
NC
CE3
BWE
ADSC
ADV
A
A
NC
A
CE2
NC
BWA
CLK
GW
OE
ADSP
A
NC
NC
NC
DQB
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
VDDQ
NC
NC
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
NC
VSS
DQB
DQB
VSS
NC
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
NC
NC
DQA
DQA
ZZ
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
DQPB
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC / 18M
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
NC
NC
NC
NC / 72M
A
A
TDI
A1
TDO
A
A
A
A
R
MODE
NC / 36M
A
A
TMS
A0
TCK
A
A
A
A
Document #: 38-05541 Rev. *A
NC / 144M
DQPA
DQA
Page 6 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Definitions
Name
I/O
Description
A0, A1 , A
InputSynchronous
Address Inputs used to select one of the address locations. Sampled at the rising
edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3[2] are sampled
active. A[1:0] feed the 2-bit counter.
BWA,BWB
BWC,BWD
InputSynchronous
Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the
SRAM. Sampled on the rising edge of CLK.
GW
InputSynchronous
Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a
global write is conducted (ALL bytes are written, regardless of the values on BWX and BWE).
CLK
InputClock
Clock Input. Used to capture all synchronous inputs to the device. Also used to increment
the burst counter when ADV is asserted LOW, during a burst operation.
CE1
InputSynchronous
CE2
InputSynchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE2 and CE3[2] to select/deselect the device. ADSP is ignored if CE1 is
HIGH.CE1 is sampled only when a new external address is loaded.
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE3[2] to select/deselect the device. CE2 is sampled only when
a new external address is loaded.
CE3[2]
InputSynchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE2 to select/ deselect the device.CE3 is sampled only when
a new external address is loaded.
OE
InputAsynchronous
Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins.
When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are
three-stated, and act as input data pins. OE is masked during the first clock of a read cycle
when emerging from a deselected state.
ADV
InputSynchronous
Advance Input signal, sampled on the rising edge of CLK. When asserted, it automatically increments the address in a burst cycle.
ADSP
InputSynchronous
ADSC
InputSynchronous
Address Strobe from Processor, sampled on the rising edge of CLK, active LOW.
When asserted LOW, addresses presented to the device are captured in the address
registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both
asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH.
Address Strobe from Controller, sampled on the rising edge of CLK, active LOW.
When asserted LOW, addresses presented to the device are captured in the address
registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both
asserted, only ADSP is recognized.
BWE
InputSynchronous
Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal
must be asserted LOW to conduct a byte write.
ZZ
InputAsynchronous
ZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a
non-time-critical “sleep” condition with data integrity preserved. For normal operation, this
pin has to be LOW or left floating. ZZ pin has an internal pull-down.
DQs
I/OSynchronous
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is
triggered by the rising edge of CLK. As outputs, they deliver the data contained in the
memory location specified by the addresses presented during the previous clock rise of
the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW,
the pins behave as outputs. When HIGH, DQs and DQPX are placed in a three-state
condition.The outputs are automatically three-stated during the data portion of a write
sequence, during the first clock when emerging from a deselected state, and when the
device is deselected, regardless of the state of OE.
DQPX
I/OSynchronous
Bidirectional Data Parity I/O Lines. Functionally, these signals are identical to DQs.
During write sequences, DQPX is controlled by BWX correspondingly.
MODE
InputStatic
VDD
VDDQ
VSS
Power Supply
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD
or left floating selects interleaved burst sequence. This is a strap pin and should remain
static during device operation. Mode Pin has an internal pull-up.
Power supply inputs to the core of the device.
I/O Power Supply Power supply for the I/O circuitry.
Ground
Document #: 38-05541 Rev. *A
Ground for the core of the device.
Page 7 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Pin Definitions (continued)
Name
VSSQ
I/O
I/O Ground
Description
Ground for the I/O circuitry.
TDO
JTAG serial output Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the
Synchronous JTAG feature is not being utilized, this pin should be left unconnected. This pin is not
available on TQFP packages.
TDI
JTAG serial input Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
Synchronous feature is not being utilized, this pin can be left floating or connected to VDD through a pull
up resistor. This pin is not available on TQFP packages.
TMS
JTAG serial input Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
Synchronous feature is not being utilized, this pin can be disconnected or connected to VDD. This pin
is not available on TQFP packages.
TCK
JTAGClock
Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must
be connected to VSS. This pin is not available on TQFP packages.
NC
–
No Connects. Not internally connected to the die. 18M, 36M, 72M, 144M and 288M are
address expansion pins are not internally connected to the die.
VSS/DNU
Ground/DNU
Document #: 38-05541 Rev. *A
This pin can be connected to Ground or should be left floating.
Page 8 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. Maximum access delay from
the clock rise (t CDV) is 6.5 ns (133-MHz device).
The CY7C1361C/CY7C1363C supports secondary cache in
systems utilizing either a linear or interleaved burst sequence.
The interleaved burst order supports Pentium® and i486
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is
user-selectable, and is determined by sampling the MODE
input. Accesses can be initiated with either the Processor
Address Strobe (ADSP) or the Controller Address Strobe
(ADSC). Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
Byte write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BWX) inputs. A Global Write
Enable (GW) overrides all byte write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self-timed write circuitry.
Three synchronous Chip Selects (CE1, CE2, CE3[2]) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output three-state control. ADSP is ignored if
CE1 is HIGH.
Single Read Accesses
A single read access is initiated when the following conditions
are satisfied at clock rise: (1) CE1, CE2, and CE3[2] are all
asserted active, and (2) ADSP or ADSC is asserted LOW (if
the access is initiated by ADSC, the write inputs must be
deasserted during this first cycle). The address presented to
the address inputs is latched into the address register and the
burst counter/control logic and presented to the memory core.
If the OE input is asserted LOW, the requested data will be
available at the data outputs a maximum to tCDV after clock
rise. ADSP is ignored if CE1 is HIGH.
Single Write Accesses Initiated by ADSP
This access is initiated when the following conditions are
satisfied at clock rise: (1) CE1, CE2, CE3[2] are all asserted
active, and (2) ADSP is asserted LOW. The addresses
presented are loaded into the address register and the burst
inputs (GW, BWE, and BWX)are ignored during this first clock
cycle. If the write inputs are asserted active (see Write Cycle
Descriptions table for appropriate states that indicate a write)
on the next clock rise,the appropriate data will be latched and
written into the device.Byte writes are allowed. All I/Os are
three-stated during a byte write.Since this is a common I/O
device, the asynchronous OE input signal must be deasserted
and the I/Os must be three-stated prior to the presentation of
data to DQs. As a safety precaution, the data lines are
three-stated once a write cycle is detected, regardless of the
state of OE.
Single Write Accesses Initiated by ADSC
This write access is initiated when the following conditions are
satisfied at clock rise: (1) CE1, CE2, and CE3[2] are all asserted
Document #: 38-05541 Rev. *A
active, (2) ADSC is asserted LOW, (3) ADSP is deasserted
HIGH, and (4) the write input signals (GW, BWE, and BWX)
indicate a write access. ADSC is ignored if ADSP is active LOW.
The addresses presented are loaded into the address register
and the burst counter/control logic and delivered to the
memory core. The information presented to DQ[A:D] will be
written into the specified address location. Byte writes are
allowed. All I/Os are three-stated when a write is detected,
even a byte write. Since this is a common I/O device, the
asynchronous OE input signal must be deasserted and the
I/Os must be three-stated prior to the presentation of data to
DQs. As a safety precaution, the data lines are three-stated
once a write cycle is detected, regardless of the state of OE.
Burst Sequences
The CY7C1361C/CY7C1363C provides an on-chip two-bit
wraparound burst counter inside the SRAM. The burst counter
is fed by A[1:0], and can follow either a linear or interleaved
burst order. The burst order is determined by the state of the
MODE input. A LOW on MODE will select a linear burst
sequence. A HIGH on MODE will select an interleaved burst
order. Leaving MODE unconnected will cause the device to
default to a interleaved burst sequence.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, CE3[2], ADSP, and ADSC must
remain inactive for the duration of tZZREC after the ZZ input
returns LOW.
Page 9 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
tZZS
tZZREC
tZZI
tRZZI
Description
Test Conditions
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
ZZ active to sleep current
ZZ Inactive to exit sleep current
Min.
ZZ > VDD – 0.2V
ZZ > VDD – 0.2V
ZZ < 0.2V
This parameter is sampled
This parameter is sampled
Max.
Unit
35
2tCYC
mA
ns
ns
ns
ns
2tCYC
2tCYC
0
Truth Table [ 3, 4, 5, 6, 7]
Cycle Description
Address
Used CE1 CE2 CE3 ZZ
ADSP
ADSC
Deselected Cycle, Power-down
None
H
X
X
L
X
L
ADV WRITE OE CLK
X
X
X
L-H
three-state
DQ
Deselected Cycle, Power-down
None
L
L
X
L
L
X
X
X
X
L-H
three-state
Deselected Cycle, Power-down
None
L
X
H
L
L
X
X
X
X
L-H
three-state
Deselected Cycle, Power-down
None
L
L
X
L
H
L
X
X
X
L-H
three-state
Deselected Cycle, Power-down
None
X
X
X
L
H
L
X
X
X
L-H
three-state
Sleep Mode, Power-down
None
X
X
X
H
X
X
X
X
X
X
three-state
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Write Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
External
External
External
External
External
Next
Next
Next
L
L
L
L
L
X
X
H
H
H
H
H
H
X
X
X
L
L
L
L
L
X
X
X
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
X
X
X
L
L
L
H
H
H
X
X
X
X
X
L
L
L
X
X
L
H
H
H
H
H
L
H
X
L
H
L
H
L
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
Q
three-state
D
Q
three-state
Q
three-state
Q
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
H
L-H
three-state
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X
L-H
D
Write Cycle, Continue Burst
Next
H
X
X
L
X
H
L
L
X
L-H
D
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
H
L-H
three-state
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
H
L-H
three-state
Write Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
L
X
L-H
D
Write Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
L
X
L-H
D
Notes:
3. X=”Don't Care.” H = Logic HIGH, L = Logic LOW.
4. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW= L. WRITE = H when all Byte write enable signals , BWE, GW = H..
5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
6. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after
the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to three-state. OE is a don't
care for the remainder of the write cycle.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are three-state when OE
is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document #: 38-05541 Rev. *A
Page 10 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Partial Truth Table for Read/Write[3, 8]
Function (CY7C1361C)
BWE
H
BWD
Read
GW
H
BWC
BWB
BWA
X
X
X
X
Read
H
L
H
H
H
H
Write Byte (A, DQPA)
H
L
H
H
H
L
Write Byte (B, DQPB)
H
L
H
H
L
H
Write Bytes (B, A, DQPA, DQPB)
H
L
H
H
L
L
Write Byte (C, DQPC)
H
L
H
L
H
H
Write Bytes (C, A, DQPC, DQPA)
H
L
H
L
H
L
Write Bytes (C, B, DQPC, DQPB)
H
L
H
L
L
H
Write Bytes (C, B, A, DQPC, DQPB, DQPA)
H
L
H
L
L
L
Write Byte (D, DQPD)
H
L
L
H
H
H
Write Bytes (D, A, DQPD, DQPA)
H
L
L
H
H
L
Write Bytes (D, B, DQPD, DQPA)
H
L
L
H
L
H
Write Bytes (D, B, A, DQPD, DQPB, DQPA)
H
L
L
H
L
L
Write Bytes (D, B, DQPD, DQPB)
H
L
L
L
H
H
Write Bytes (D, B, A, DQPD, DQPC, DQPA)
H
L
L
L
H
L
Write Bytes (D, C, A, DQPD, DQPB, DQPA)
H
L
L
L
L
H
Write All Bytes
H
L
L
L
L
L
Write All Bytes
L
X
X
X
X
X
Truth Table for Read/Write[3, 8]
Function (CY7C1363C)
Read
GW
H
BWE
H
BWB
X
BWA
X
Read
H
L
H
H
Write Byte A – ( DQA and DQPA)
H
L
H
L
Write Byte B – ( DQB and DQPB)
H
L
L
H
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
Note:
8. Table only lists a partial listing of the byte write combinations. Any Combination of BWX is valid Appropriate write will be done based on which byte write is active.
Document #: 38-05541 Rev. *A
Page 11 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
IEEE 1149.1 Serial Boundary Scan (JTAG)
Test MODE SELECT (TMS)
The CY7C1361C/CY7C1363C incorporates a serial boundary
scan test access port (TAP) in the BGA package only. The
TQFP package does not offer this functionality. This part
operates in accordance with IEEE Standard 1149.1-1900, but
doesn’t have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note the TAP controller
functions in a manner that does not conflict with the operation
of other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3V or 2.5V I/O logic levels.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this ball unconnected if the TAP is not used. The ball is
pulled up internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The CY7C1361C/CY7C1363C contains a TAP controller,
instruction register, boundary scan register, bypass register,
and ID register.
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. For
information on loading the instruction register, see Figure .
TDI is internally pulled up and can be unconnected if the TAP
is unused in an application. TDI is connected to the most
significant bit (MSB) of any register. (See Tap Controller Block
Diagram.)
Disabling the JTAG Feature
Test Data-Out (TDO)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should be
left unconnected. Upon power-up, the device will come up in
a reset state which will not interfere with the operation of the
device.
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See Tap Controller State Diagram.)
TAP Controller Block Diagram
0
TAP Controller State Diagram
1
Bypass Register
TEST-LOGIC
RESET
2 1 0
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCAN
1
SELECT
IR-SCAN
0
1
CAPTURE-DR
0
Selection
Circuitry
TDO
Identification Register
CAPTURE-IR
x . . . . . 2 1 0
Boundary Scan Register
SHIFT-IR
1
Instruction Register
31 30 29 . . . 2 1 0
0
SHIFT-DR
0
1
EXIT1-DR
1
EXIT1-IR
0
1
TCK
0
PAUSE-DR
0
TMS
PAUSE-IR
1
TAP CONTROLLER
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
1
TDI
0
1
0
0
1
Selection
Circuitry
0
UPDATE-IR
1
0
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
At power-up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Document #: 38-05541 Rev. *A
TAP Registers
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Page 12 of 30
PRELIMINARY
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the Tap Controller Block
Diagram. Upon power-up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board-level serial test data path.
Bypass Register
CY7C1361C
CY7C1363C
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with all
0s. EXTEST is not implemented in this SRAM TAP controller,
and therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-0 instruction.
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between
the two instructions. Unlike the SAMPLE/PRELOAD
instruction, EXTEST places the SRAM outputs in a High-Z
state.
Boundary Scan Register
IDCODE
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the I/O ring.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and should not be used. The other five instructions are described in detail below.
The TAP controller used in this SRAM is not fully compliant to
the 1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the I/O
buffers. The SRAM does not implement the 1149.1 commands
EXTEST or INTEST or the PRELOAD portion of
SAMPLE/PRELOAD; rather, it performs a capture of the I/O
ring when these instructions are executed.
Document #: 38-05541 Rev. *A
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1-mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will
undergo a transition. The TAP may then try to capture a signal
while in transition (metastable state). This will not harm the
device, but there is no guarantee as to the value that will be
captured. Repeatable results may not be possible.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture set-up plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE / PRELOAD instruction. If
this is an issue, it is still possible to capture all other signals
and simply ignore the value of the CK and CK# captured in the
boundary scan register.
Page 13 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
BYPASS
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins.
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO balls. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
prior to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required–that is, while data
captured is shifted out, the preloaded data can be shifted in.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
Test Clock
(TCK)
3
t TH
t TMSS
t TMSH
t TDIS
t TDIH
t
TL
4
5
6
t CYC
Test Mode Select
(TMS)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
TAP AC Switching Characteristics Over the Operating Range[9, 10]
Parameter
Parameter
Clock
tTCYC
TCK Clock Cycle Time
TCK Clock Frequency
tTF
TCK Clock HIGH time
tTH
tTL
TCK Clock LOW time
Output Times
TCK Clock LOW to TDO Valid
tTDOV
tTDOX
TCK Clock LOW to TDO Invalid
Setup Times
TMS Set-Up to TCK Clock Rise
tTMSS
TDI Set-Up to TCK Clock Rise
tTDIS
tCS
Capture Set-Up to TCK Rise
Hold Times
TMS hold after TCK Clock Rise
tTMSH
tTDIH
TDI Hold after Clock Rise
Capture Hold after Clock Rise
tCH
Min.
Max.
50
20
25
25
5
0
Unit
ns
MHz
ns
ns
ns
ns
5
5
5
ns
ns
5
5
5
ns
ns
ns
Notes:
9. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
10. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
Document #: 38-05541 Rev. *A
Page 14 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels ........ ........................................VSS to 3.3V
Input pulse levels ......................................... VSS to 2.5V
Input rise and fall times ...................... ..............................1ns
Input rise and fall time .....................................................1 ns
Input timing reference levels ...........................................1.5V
Input timing reference levels................... ......................1.25V
Output reference levels...................................................1.5V
Output reference levels .................. ..............................1.25V
Test load termination supply voltage...............................1.5V
Test load termination supply voltage .................... ........1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.5V
1.25V
50Ω
50Ω
TDO
TDO
Z O= 50Ω
Z O= 50Ω
20pF
20pF
TAP DC Electrical Characteristics And Operating Conditions (0°C < TA < +70°C; VDD = 3.3V ±0.165V unless
otherwise noted)[11]
Parameter
VOH1
VOH2
VOL1
VOL2
VIH
VIL
IX
Description
Output HIGH Voltage
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Description
Conditions
Min.
IOH = –4.0 mA
VDDQ = 3.3V
2.4
V
IOH = –1.0 mA
VDDQ = 2.5V
2.0
V
IOH = –100 µA
VDDQ = 3.3V
2.9
V
VDDQ = 2.5V
2.1
V
Unit
IOL = 8.0 mA
VDDQ = 3.3V
0.4
V
IOL = 8.0 mA
VDDQ = 2.5V
0.4
V
IOL = 100 µA
VDDQ = 3.3V
0.2
V
VDDQ = 2.5V
0.2
V
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Max.
VDDQ = 3.3V
2.0
VDD + 0.3
V
VDDQ = 2.5V
1.7
VDD + 0.3
V
VDDQ = 3.3V
–0.5
0.7
V
VDDQ = 2.5V
–0.3
0.7
V
–5
5
µA
GND < VIN < VDDQ
Identification Register Definitions
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
[12]
Device Width (23:18)
Cypress Device ID (17:12)
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
CY7C1361C
(256K x36)
CY7C1363C
(512K x18)
Description
000
000
01011
01011
000001
000001
Defines memory type and architecture
Defines width and density
100110
010110
00000110100
00000110100
1
1
Describes the version number.
Reserved for Internal Use
Allows unique identification of SRAM vendor.
Indicates the presence of an ID register.
Note:
11. All voltages referenced to VSS (GND) .
12. Bit #24 is “1” in the Register Definitions for both 2.5v and 3.3v versions of this device.
Document #: 38-05541 Rev. *A
Page 15 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Scan Register Sizes
Register Name
Bit Size (×36) Bit Size (×18)
3
Instruction
3
Bypass
1
1
ID
32
32
Boundary Scan Order
(119-ball BGA package)
71
71
Boundary Scan Order
(165-ball fBGA package)
71
71
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures I/O ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High-Z state.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and
TDO. This operation does not affect SRAM operations.
SAMPLE Z
010
Captures I/O ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM operations.
Document #: 38-05541 Rev. *A
Page 16 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
119-Ball BGA Boundary Scan Order
CY7C1361C (256K x 36)
CY7C1363C (512K x 18)
BALL
ID
Signal
Name
BIT#
BALL ID
Signal
Name
BIT#
BALL ID
Signal
Name
BIT#
BALL ID
Signal
Name
CLK
37
P4
A0
1
2
K4
H4
CLK
37
P4
A0
2
K4
H4
GW
38
N4
A1
3
M4
BWE
GW
38
N4
A1
39
R6
4
F4
OE
40
T5
A
3
M4
BWE
39
R6
A
A
4
F4
OE
40
T5
A
5
B4
ADSC
41
T3
A
6
A4
ADSP
42
R2
A
5
B4
ADSC
41
T3
A
6
A4
ADSP
42
R2
A
7
G4
ADV
43
R3
MODE
7
G4
ADV
43
R3
MODE
8
C3
A
44
P2
DQPD
8
C3
A
44
Internal
Internal
9
B3
A
45
P1
DQD
9
B3
A
45
Internal
Internal
10
D6
DQPB
46
L2
DQD
10
T2
A
46
Internal
Internal
11
H7
DQB
47
K1
DQD
11
Internal
Internal
47
Internal
Internal
12
13
G6
DQB
48
N2
DQD
12
Internal
Internal
48
P2
DQPB
E6
DQB
49
N1
DQD
13
Internal
Internal
49
N1
DQB
14
D7
DQB
50
M2
DQD
14
D6
DQPA
50
M2
DQB
15
E7
DQB
51
L1
DQD
15
E7
DQA
51
L1
DQB
16
F6
DQB
52
K2
DQD
16
F6
DQA
52
K2
DQB
17
G7
DQB
53
Internal
Internal
17
G7
DQA
53
Internal
Internal
18
H6
DQB
54
H1
DQC
18
H6
DQA
54
H1
DQB
19
T7
ZZ
55
G2
DQC
19
T7
ZZ
55
G2
DQB
20
K7
DQA
56
E2
DQC
20
K7
DQA
56
E2
DQB
21
L6
DQA
57
D1
DQC
21
L6
DQA
57
D1
DQB
22
N6
DQA
58
H2
DQC
22
N6
DQA
58
Internal
Internal
23
P7
DQA
59
G1
DQC
23
P7
DQA
59
Internal
Internal
24
N7
DQA
60
F2
DQC
24
Internal
Internal
60
Internal
Internal
25
M6
DQA
61
E1
DQC
25
Internal
Internal
61
Internal
Internal
26
L7
DQA
62
D2
DQPC
26
Internal
Internal
62
Internal
Internal
27
K6
DQA
63
C2
A
27
Internal
Internal
63
C2
A
28
P6
DQPA
64
A2
A
28
Internal
Internal
64
A2
A
29
T4
A
65
E4
CE1
29
T6
A
65
E4
CE1
30
A3
A
66
B2
CE2
30
A3
A
66
B2
CE2
31
C5
A
67
L3
BWD
31
C5
A
67
Internal
Internal
32
B5
A
68
G3
BWC
32
B5
A
68
Internal
Internal
33
A5
A
69
G5
BWB
33
A5
A
69
G3
BWB
34
C6
A
70
L5
BWA
34
C6
A
70
L5
BWA
35
A6
A
71
Internal
Internal
35
A6
A
71
Internal
Internal
36
B6
A
36
B6
A
BIT#
1
Document #: 38-05541 Rev. *A
Page 17 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
165-Ball fBGA Boundary Scan Order
CY7C1361C (256K x 36)
CY7C1363C (512K x 18)
BIT#
BALL
ID
Signal
Name
BIT#
BALL ID
Signal
Name
1
B6
CLK
37
R6
A0
2
B7
GW
38
P6
A1
3
A7
BWE
39
R4
A
4
B8
OE
40
P4
A
5
A8
ADSC
41
R3
A
6
B9
ADSP
42
P3
A
7
A9
ADV
43
R1
MODE
8
B10
A
44
N1
DQPD
BALL ID
Signal
Name
BIT#
BALL ID
1
B6
CLK
37
R6
A0
2
B7
GW
38
P6
A1
3
A7
BWE
39
R4
A
4
B8
OE
40
P4
A
5
A8
ADSC
41
R3
A
6
B9
ADSP
42
P3
A
7
A9
ADV
43
R1
MODE
8
B10
A
44
Internal
Internal
BIT#
Signal
Name
9
A10
A
45
L2
DQD
9
A10
A
45
Internal
Internal
10
C11
DQPB
46
K2
DQD
10
A11
A
46
Internal
Internal
11
E10
DQB
47
J2
DQD
11
Internal
Internal
47
Internal
Internal
12
F10
DQB
48
M2
DQD
12
Internal
Internal
48
N1
DQPB
13
G10
DQB
49
M1
DQD
13
Internal
Internal
49
M1
DQB
14
D10
DQB
50
L1
DQD
14
C11
DQPA
50
L1
DQB
15
D11
DQB
51
K1
DQD
15
D11
DQA
51
K1
DQB
16
E11
DQB
52
J1
DQD
16
E11
DQA
52
J1
DQB
17
F11
DQB
53
Internal
Internal
17
F11
DQA
53
Internal
Internal
18
G11
DQB
54
G2
DQC
18
G11
DQA
54
G2
DQB
19
H11
ZZ
55
F2
DQC
19
H11
ZZ
55
F2
DQB
20
J10
DQA
56
E2
DQC
20
J10
DQA
56
E2
DQB
21
K10
DQA
57
D2
DQC
21
K10
DQA
57
D2
DQB
22
L10
DQA
58
G1
DQC
22
L10
DQA
58
Internal
Internal
23
M10
DQA
59
F1
DQC
23
M10
DQA
59
Internal
Internal
24
J11
DQA
60
E1
DQC
24
Internal
Internal
60
Internal
Internal
25
K11
DQA
61
D1
DQC
25
Internal
Internal
61
Internal
Internal
26
L11
DQA
62
C1
DQPC
26
Internal
Internal
62
Internal
Internal
27
M11
DQA
63
B2
A
27
Internal
Internal
63
B2
A
28
N11
DQPA
64
A2
A
28
Internal
Internal
64
A2
A
29
R11
A
65
A3
CE1
29
R11
A
65
A3
CE1
30
R10
A
66
B3
CE2
30
R10
A
66
B3
CE2
31
P10
A
67
B4
BWD
31
P10
A
67
Internal
Internal
32
R9
A
68
A4
BWC
32
R9
A
68
Internal
Internal
33
P9
A
69
A5
BWB
33
P9
A
69
A4
BWB
34
R8
A
70
B5
BWA
34
R8
A
70
B5
BWA
71
A6
CE3
71
A6
CE3
35
P8
A
36
P11
A
Document #: 38-05541 Rev. *A
35
P8
A
36
P11
A
Page 18 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Maximum Ratings
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage........................................... >2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired. For user guidelines, not tested.)
Latch-up Current..................................................... >200 mA
Storage Temperature ................................. –65°C to +150°C
Operating Range
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Ambient
Range
Temperature
VDD
VDDQ
Commercial 0°C to +70°C 3.3V – 5%/+10% 2.5V – 5%
to VDD
Industrial
–40°C to +85°C
Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V
DC Voltage Applied to Outputs
in three-state ....................................... –0.5V to VDDQ + 0.5V
DC Input Voltage....................................–0.5V to VDD + 0.5V
Electrical Characteristics Over the Operating Range
Parameter
Description
VDD
VDDQ
Power Supply Voltage
I/O Supply Voltage
VOH
Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage[13]
VIL
Input LOW Voltage[13]
IX
Input Load
[13, 14]
Test Conditions
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V, VDD = Min., IOH = –4.0 mA
VDDQ = 2.5V, VDD = Min., IOH = –1.0 mA
VDDQ = 3.3V, VDD = Min., IOL = 8.0 mA
VDDQ = 2.5V, VDD = Min., IOL = 1.0 mA
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
GND ≤ VI ≤ VDDQ
Input Current of MODE Input = VSS
Min.
Max.
Unit
3.135
3.135
2.375
2.4
2.0
3.6
VDD
2.625
V
V
V
V
V
V
V
V
V
V
V
µA
2.0
1.7
–0.3
–0.3
–5
5
Input = VSS
Output Leakage Current GND ≤ VI ≤ VDD, Output Disabled
IDD
VDD Operating Supply
Current
VDD = Max., IOUT = 0 mA,
f = fMAX = 1/tCYC
Max. VDD, Device Deselected,
VIN ≥ VIH or VIN ≤ VIL, f = fMAX,
inputs switching
µA
µA
–5
Input = VDD
IOZ
µA
–30
Input = VDD
Input Current of ZZ
0.4
0.4
VDD + 0.3V
VDD + 0.3V
0.8
0.7
5
30
µA
5
µA
7.5-ns cycle, 133 MHz
250
mA
8.8-ns cycle, 117 MHz
220
mA
10-ns cycle, 100 MHz
180
All speeds
40
mA
–5
ISB1
Automatic CE
Power-down
Current—TTL Inputs
ISB2
Automatic CE
Max. VDD, Device Deselected,
Power-down
VIN ≥ VDD – 0.3V or VIN ≤ 0.3V,
Current—CMOS Inputs f = 0, inputs static
All speeds
30
mA
ISB3
Max. VDD, Device Deselected,
Automatic CE
Power-down
VIN ≥ VDDQ – 0.3V or VIN ≤ 0.3V,
Current—CMOS Inputs f = fMAX, inputs switching
All speeds
40
mA
ISB4
Automatic CE
Power-down
Current—TTL Inputs
All Speeds
40
mA
Max. VDD, Device Deselected,
VIN ≥ VDD – 0.3V or VIN ≤ 0.3V,
f = 0, inputs static
Notes:
13. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > -2V (Pulse width less than tCYC/2).
14. TPower-up: Assumes a linear ramp from 0v to VDD(min.) within 200ms. During this time VIH < VDD and VDDQ < VDD.
Document #: 38-05541 Rev. *A
Page 19 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Thermal Resistance[15]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
Test conditions follow standard
test methods and procedures
for measuring thermal
impedance, per EIA/JESD51
TQFP
Package
BGA
Package
fBGA
Package
Unit
25
25
27
°C/W
9
6
6
°C/W
Capacitance[15]
Parameter
Description
TQFP
Package
Test Conditions
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CI/O
Input/Output Capacitance
TA = 25°C, f = 1 MHz,
VDD = 3.3V
VDDQ = 2.5V
BGA
Package
fBGA
Package
Unit
5
5
5
pF
5
5
5
pF
5
7
7
pF
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
VT = 1.5V
(a)
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
GND
5 pF
INCLUDING
JIG AND
SCOPE
R = 351Ω
90%
10%
90%
10%
≤ 1ns
≤ 1ns
(b)
(c)
2.5V I/O Test Load
R = 1667Ω
2.5V
OUTPUT
Z0 = 50Ω
VT = 1.25V
(a)
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
GND
5 pF
INCLUDING
JIG AND
SCOPE
R =1538Ω
90%
10%
90%
10%
≤ 1ns
≤ 1ns
(b)
(c)
Switching Characteristics Over the Operating Range[20, 21]
133 MHz
Parameter
tPOWER
Description
Min.
[16]
VDD(Typical) to the first Access
Max.
1
117 MHz
Min.
Max.
1
100 MHz
Min.
Max.
1
Unit
ms
Clock
tCYC
Clock Cycle Time
7.5
8.5
10
ns
tCH
Clock HIGH
3.0
3.2
4.0
ns
tCL
Clock LOW
3.0
3.2
4.0
ns
Output Times
tCDV
Data Output Valid After CLK Rise
tDOH
Data Output Hold After CLK Rise
2.0
tCLZ
Clock to
Low-Z[17, 18, 19]
0
tCHZ
Clock to High-Z[17, 18, 19]
tOEV
OE LOW to Output Valid
tOELZ
OE LOW to Output Low-Z[17, 18, 19]
6.5
7.5
2.0
0
3.5
ns
3.5
3.5
0
3.5
0
ns
ns
0
3.5
3.5
0
8.5
2.0
ns
ns
ns
Note:
15. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05541 Rev. *A
Page 20 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Switching Characteristics Over the Operating Range[20, 21]
133 MHz
Parameter
tOEHZ
Description
Min.
[17, 18, 19]
Max.
117 MHz
Min.
3.5
OE HIGH to Output High-Z
Max.
100 MHz
Min.
3.5
Max.
Unit
3.5
ns
Set-up Times
tAS
Address Set-up Before CLK Rise
1.5
1.5
1.5
ns
tADS
ADSP, ADSC Set-up Before CLK Rise
1.5
1.5
1.5
ns
tADVS
ADV Set-up Before CLK Rise
GW, BWE, BW[A:D] Set-up Before CLK
Rise
1.5
1.5
1.5
ns
tWES
1.5
1.5
1.5
ns
tDS
Data Input Set-up Before CLK Rise
1.5
1.5
1.5
ns
tCES
Chip Enable Set-up
1.5
1.5
1.5
ns
Address Hold After CLK Rise
0.5
0.5
0.5
ns
ADSP, ADSC Hold After CLK Rise
GW,BWE, BW[A:D] Hold After CLK Rise
0.5
0.5
0.5
ns
0.5
0.5
0.5
ns
0.5
0.5
ns
tDH
ADV Hold After CLK Rise
Data Input Hold After CLK Rise
0.5
0.5
0.5
0.5
ns
tCEH
Chip Enable Hold After CLK Rise
0.5
0.5
0.5
ns
Hold Times
tAH
tADH
tWEH
tADVH
Notes:
16. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD( minimum) initially, before a read or write operation
can be initiated.
17. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
18. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions
19. This parameter is sampled and not 100% tested.
20. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V.
21. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05541 Rev. *A
Page 21 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Timing Diagrams
Read Cycle Timing[22]
tCYC
CLK
t
tADS
t CL
CH
tADH
ADSP
tADS
tADH
ADSC
tAS
tAH
A1
ADDRESS
A2
t
WES
t
WEH
GW, BWE,BW
X
Deselect Cycle
tCES t CEH
CE
t
t
ADVS ADVH
ADV
ADV suspends burst
OE
t OEV
t OEHZ
t CLZ
Data Out (Q)
High-Z
Q(A1)
t OELZ
tCDV
t CHZ
tDOH
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
t CDV
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
Burst wraps around
to its initial state
Single READ
BURST
READ
DON’T CARE
UNDEFINED
Note:
22. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
Document #: 38-05541 Rev. *A
Page 22 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Timing Diagrams (continued)
Write Cycle Timing[22, 23]
t CYC
CLK
t
tADS
t
CH
CL
tADH
ADSP
tADS
ADSC extends burst
tADH
tADS
tADH
ADSC
tAS
tAH
A1
ADDRESS
A2
A3
Byte write signals are ignored for first cycle when
ADSP initiates burst
tWES tWEH
BWE,
BWX
t
t
WES WEH
GW
tCES
tCEH
CE
tADVS tADVH
ADV
ADV suspends burst
OE
t
Data in (D)
High-Z
t
OEHZ
DS
t
DH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
DON’T CARE
Extended BURST WRITE
UNDEFINED
Notes:
23. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BWX LOW.
Document #: 38-05541 Rev. *A
Page 23 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Timing Diagrams (continued)
Read/Write Cycle Timing[22, 24, 25]
tCYC
CLK
t
CH
tADS
tADH
tAS
tAH
t
CL
ADSP
ADSC
ADDRESS
A1
A2
A3
A4
A5
A6
D(A5)
D(A6)
t
t
WES WEH
BWE, BWX
tCES
tCEH
CE
ADV
OE
tDS
Data In (D)
Data Out (Q)
High-Z
t
OEHZ
Q(A1)
tDH
tOELZ
D(A3)
tCDV
Q(A2)
Back-to-Back READs
Q(A4)
Single WRITE
Q(A4+1)
Q(A4+2)
Q(A4+3)
BURST READ
DON’T CARE
Back-to-Back
WRITEs
UNDEFINED
Notes:
24. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC.
25. GW is HIGH.
26. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
27. DQs are in high-Z when exiting ZZ sleep mode.
Document #: 38-05541 Rev. *A
Page 24 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Timing Diagrams (continued)
ZZ Mode Timing[26, 27]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Ordering Information
Speed
(MHz)
133
Ordering Code
CY7C1361C-133AXC
Package
Name
100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm)
3 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm)
3 Chip Enables
Industrial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm)
2 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm)
2 Chip Enables
Industrial
CY7C1363C-133AXI
CY7C1361C-133AJXC
CY7C1363C-133AJXC
CY7C1361C-133AJXI
CY7C1363C-133AJXI
CY7C1361C-133BGC
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Commercial
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Industrial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
3 Chip Enables and JTAG
Commercial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
3 Chip Enables and JTAG
Industrial
CY7C1363C-133BGC
CY7C1361C-133BGI
CY7C1363C-133BGI
CY7C1361C-133BZC
CY7C1363C-133BZC
CY7C1361C-133BZI
CY7C1363C-133BZI
Document #: 38-05541 Rev. *A
Operating
Range
A101
CY7C1363C-133AXC
CY7C1361C-133AXI
Part and Package Type
Page 25 of 30
PRELIMINARY
CY7C1361C
CY7C1363C
Ordering Information (continued)
Speed
(MHz)
117
Ordering Code
CY7C1361C-117AXC
Package
Name
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
3 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
3 Chip Enables
Industrial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
2 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
2 Chip Enables
Industrial
CY7C1363C-117AXI
CY7C1361C-117AJXC
CY7C1363C-117AJXC
CY7C1361C-117AJXI
CY7C1363C-117AJXI
CY7C1361C-117BGC
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Commercial
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Industrial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4mm)
3 Chip Enables and JTAG
Commercial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4mm)
3 Chip Enables and JTAG
Industrial
CY7C1363C-117BGC
CY7C1361C-117BGI
CY7C1363C-117BGI
CY7C1361C-117BZC
CY7C1363C-117BZC
CY7C1361C-117BZI
CY7C1363C-117BZI
100
CY7C1361C-100AXC
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
3 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
3 Chip Enables
Industrial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
2 Chip Enables
Commercial
A101
100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm)
2 Chip Enables
Industrial
CY7C1363C-100AXC
CY7C1361C-100AXI
CY7C1363C-100AXI
CY7C1361C-100AJXC
CY7C1363C-100AJXC
CY7C1361C-100AJXI
CY7C1363C-100AJXI
CY7C1361C-100BGC
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Commercial
BG119
119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and
JTAG
Industrial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4mm)
3 Chip Enables and JTAG
Commercial
BB165D
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4mm)
3 Chip Enables and JTAG
Industrial
CY7C1363C-100BGC
CY7C1361C-100BGI
CY7C1363C-100BGI
CY7C1361C-100BZC
CY7C1363C-100BGC
CY7C1361C-100BZI
CY7C1363C-100BGI
Operating
Range
A101
CY7C1363C-117AXC
CY7C1361C-117AXI
Part and Package Type
Shaded areas contain advance information. Please contact your local sales representative for availability of these parts.Lead-free BG and BZ packages (Ordering
code:BGX,BZX) will be available in 2005.
Document #: 38-05541 Rev. *A
Page 26 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Package Diagrams
100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101
DIMENSIONS ARE IN MILLIMETERS.
16.00±0.20
1.40±0.05
14.00±0.10
100
81
80
1
20.00±0.10
22.00±0.20
0.30±0.08
0.65
TYP.
30
SEE DETAIL
50
0.20 MAX.
1.60 MAX.
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
GAUGE PLANE
0.10
0° MIN.
0°-7°
A
51
31
R 0.08 MIN.
0.20 MAX.
12°±1°
(8X)
SEATING PLANE
R 0.08 MIN.
0.20 MAX.
0.60±0.15
0.20 MIN.
1.00 REF.
DETAIL
Document #: 38-05541 Rev. *A
A
51-85050-*A
Page 27 of 30
PRELIMINARY
CY7C1361C
CY7C1363C
Package Diagrams (continued)
119-Lead PBGA (14 x 22 x 2.4 mm) BG119
51-85115-*B
Document #: 38-05541 Rev. *A
Page 28 of 30
CY7C1361C
CY7C1363C
PRELIMINARY
Package Diagrams (continued)
165 FBGA 13 x 15 x 1.40 mm BB165D
51-85180-**
i486 is a trademark, and Intel and Pentium are registered trademarks of Intel Corporation. PowerPC is a trademark of IBM
Corporation. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05541 Rev. *A
Page 29 of 30
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY7C1361C
CY7C1363C
PRELIMINARY
Document History Page
Document Title: CY7C1361C/CY7C1363C 9-Mbit (256K x 36/512K x 18) Flow-Through SRAM (Preliminary)
Document Number: 38-05541
REV.
ECN NO.
Issue Date
Orig. of
Change
**
241690
See ECN
RKF
New data sheet
*A
278969
See ECN
RKF
Changed Boundary Scan order to match the B rev of these devices.
Document #: 38-05541 Rev. *A
Description of Change
Page 30 of 30
Similar pages