Cypress CYIFS784BSXCT Low emi spectrum spread clock Datasheet

FS781/82/84
Low EMI Spectrum Spread Clock
Features
Functional Description
• Spread Spectrum clock generator (SSCG) with 1×, 2×,
and 4× outputs
• 6- to 82-MHz operating frequency range
• Modulates external clocks including crystals, crystal
oscillators, or ceramic resonators
• Programmable modulation with simple R-C external
loop filter (LF)
• Center spread modulation
• 3V-5V power supply
• TTL-/CMOS-compatible outputs
The Cypress FS781/82/84 are Spread Spectrum clock
generator ICs (SSCG) designed for the purpose of reducing
electromagnetic interference (EMI) found in today’s
high-speed digital systems.
The FS781/82/84 SSCG clocks use a Cypress-proprietary
technology to modulate the input clock frequency, XIN, by
modulating the frequency of the digital clock. By modulating
the reference clock the measured EMI at the fundamental and
harmonic frequencies of FSOUT is greatly reduced. This
reduction in radiated energy can significantly reduce the cost
of complying with regulatory requirements without degrading
digital waveforms.
The Cypress FS781/82/84 clocks are very simple and
versatile devices to use. By programming the two range select
lines, S0 and S1, any frequency from 6- to 82-MHz operating
range can be selected. The FS781/2/4 are designed to
operate over a very wide range of input frequencies and
provides 1×, 2×, and 4× modulated clock outputs.
• Low short-term jitter
• Low-power Dissipation
— 3.3 VDC = 37 mW – typical
— 5.0 VDC = 115 mW – typical
• Available in 8-pin SOIC and TSSOP packages
Applications
• Desktop/notebook computers
• Printers, copiers, and MFP
• Scanners and fax
The FS78x devices have a simple frequency selection table
that allows operation from 6 MHz to 82 MHz in four separate
ranges. The bandwidth of the frequency spread at FSOUT is
determined by the values of the loop filter components. The
modulation rate is determined internally by the input frequency
and the selected input frequency range.
The Bandwidth of these products can be programmed from as
little as 1.0% up to as much as 4.0% by selecting the proper
loop filter value. Refer to the Loop Filter Selection chart in
Table 2 and Table 3 for the recommended values. Due to a
wide range of application requirements, an external loop filter
(LF) is used on the FS78x products. The user can select the
exact amount of frequency modulation suitable for the application. Using a fixed internal loop filter would severely limit
the use of a wide range of modulation bandwidths (Spread %)
to a few discrete values. Refer to FS791/2/4 products for applications requiring 80- to 140-MHz frequency range.
• LCD displays and monitors
• CD-ROM, VCD, and DVD
• Automotive and embedded systems
• Networking, LAN/WAN
• Digital cameras and camcorders
• Modems
Benefits
• Programmable EMI reduction
• Fast time to market
• Lower cost of compliance
• No degradation in rise/fall times
• Lower component and PCB layer count
Cypress Semiconductor Corporation
Document #: 38-07029 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 2, 2005
[+] Feedback
FS781/82/84
Pin Configuration
Block Diagram
Loop Filter
4(6)
250 K
Xin
Reference
Divider
1(3)
Phase
Detector
8 pF
Xin
1
8
VDD
Xout
2
7
S0
S1
3
6
FSOUT
4
5
VSS
LF
FS78x
VCO
8 Pin SOIC Package
10 pF.
Xout
Modulation
Control
2(4)
VCO / N
8 pF
VDD
Power Contol
Logic
8(2)
VDD
Output
Divider
and
Mux
Input Control Logic
S1
VSS
FSOUT
1
8
FSOUT
2
7
VSS
Xin
3
6
LF
4
5
S1
Xout
VSS
FS78x
(TSSOP Pin #)
7(1)
3(5)
5(7)
6(8)
S0
VDD
8 Pin TSSOP Package
S0
Pin Description
Pin
Name
I/O
Type
1/2 (SOIC)
3/4 (TSSOP)
XIN/XOUT
I/O
7/3 (SOIC)
1/5 (TSSOP)
S0 / S1
I
CMOS/TTL Digital control inputs to select input frequency range and output
frequency scaling. Refer to Table 2 and Table 3 for selection. S0 has internal
pull-down. S1 has internal pull-up.
4 (SOIC)
6 (TSSOP)
LF
I
Analog
6 (SOIC)
8 (TSSOP)
FSOUT
O
CMOS/TTL Modulated Clock Frequency Output. The center frequency is the same as
the input reference frequency for FS781. Input frequency is multiplied by 2×
and 4× for FS782 and FS784, respectively.
8 (SOIC)
2 (TSSOP)
VDD
P
Power
Positive Power Supply.
5 (SOIC)
7 (TSSOP)
VSS
P
Power
Power Supply Ground.
Analog
Description
Pins form an on-chip reference oscillator when connected to terminals
of an external parallel resonant crystal. XIN may be connected to
TTL/CMOS external clock source. If XIN is connected to an external clock
other than crystal, leave XOUT (pin 2) unconnected.
Loop Filter. Single ended three-state output of the phase detector. A two-pole
passive loop filter is connected to LF.
Output Frequency Selection
Table 1. FSOUT SSCG (Modulated Output Clock) Product Selection
Product Number
FSOUT Frequency Scaling
FS781
1×
1× modulated frequency of input clock
Description
FS782
2×
2× modulated frequency of input clock
FS784
4×
4× modulated frequency of input clock
Loop Filter Selection Chart
The following table provides a list of recommended loop filter
values for the FS781/82/84. The FS78X is divided into four
ranges and operated at both 3.3V and 5.5 VDC. The loop filter
at the right is representative of the loop filter components in
Table 2.
Document #: 38-07029 Rev. *F
R6
LF (pin 4)
C8
C7
Page 2 of 12
[+] Feedback
FS781/82/84
Table 2. FS781/82/84 Recommended Loop Filter Values C7 (pF) @ +3.3 VDC ±5% (R6 = 3.3K)[1, 2, 3, 4]
Input MHz S1
6
0
S0
BW = 1.0%[3]
BW = 1.5%[3] BW = 2.0%[3] BW = 2.5%[3] BW = 3.0%[3] BW = 3.5%[3] BW = 4.0%[3]
0
10,000/1000
1550
910
780
700
640
560
8
0
0
10,000/330
990
820
640
520
450
400
10
0
0
1040
680
460
360
300
240
210
12
0
0
830
420
300
220
200
190
170
14
0
0
580
230
200
160
140
100
80
16
0
1
10000
980
760
580
470
410
385
18
0
1
1200
750
580
470
415
370
300
20
0
1
1000
730
470
390
320
220
190
22
0
1
960
640
410
270
230
200
180
24
0
1
920
400
250
210
180
160
150
26
0
1
660
300
220
180
150
140
120
28
0
1
470
230
180
150
130
100
70
30
0
1
470
180
140
120
100
80
60
32
0
1
330
170
120
100
82
68
47
34
1
0
10000
860
640
520
430
380
330
36
1
0
2200
820
620
470
400
330
290
38
1
0
1500
690
520
410
340
290
240
40
1
0
960
600
420
340
280
220
160
42
1
0
940
620
380
275
230
210
180
44
1
0
950
680
400
250
210
190
170
46
1
0
900
580
270
220
190
180
165
48
1
0
790
440
260
210
180
160
140
50
1
0
660
360
250
190
170
150
140
52
1
0
470
325
220
185
155
135
120
54
1
0
470
270
200
170
140
130
100
56
1
0
445
250
185
150
120
85
47
58
1
0
430
210
165
130
100
65
33
60
1
0
295
185
150
120
100
90
82
62
1
0
270
220
150
120
100
82
68
64
1
1
1180
860
560
410
340
290
230
65
1
1
1180
850
540
400
330
280
220
66
1
1
1180
760
560
350
260
220
210
68
1
1
1180
750
500
320
260
230
210
70
1
1
1120
740
470
370
300
240
170
72
1
1
1160
780
470
300
250
220
190
74
1
1
1110
770
470
280
230
210
190
76
1
1
1000
720
440
240
210
190
170
78
1
1
910
670
270
210
190
170
160
80
1
1
900
620
260
210
190
170
156
82
1
1
900
540
250
210
190
170
150
Notes:
1. If the value selected from the above chart is not a standard, use the next available larger value.
2. All bandwidths indicated above are total peak-to-peak spread. 1% = +0.5% to –0.5%. 4% = +2.0% to –2.0%.
3. If C8 is not listed in the chart for a particular bandwidth and frequency, it is not used in the loop filter.
4. Contact Cypress for LF values less than 1.0% bandwidth.
Document #: 38-07029 Rev. *F
Page 3 of 12
[+] Feedback
FS781/82/84
Table 3. FS781/82/84 Recommended Loop Filter Values C7 (pF) @ +5.0 VDC ±5% (R6 = 3.3K)[1, 2, 3, 4]
Input MHz
S1
S0
6
0
0
BW = 1.0%[3] BW = 1.5%[3] BW = 2.0%[3] BW = 2.5%[3] BW = 3.0%[3] BW = 3.5%[3] BW = 4.0%[3]
1140
1030
930
830
710
610
510
8
0
0
1170
970
740
570
460
400
280
10
0
0
1030
660
430
350
280
210
130
12
0
0
760
340
230
200
180
160
130
14
0
0
450
240
180
140
100
70
50
16
0
1
2490
970
730
590
480
430
370
18
0
1
2490
870
650
510
430
370
310
20
0
1
1360
680
480
370
280
190
250
22
0
1
990
560
330
260
230
200
190
24
0
1
820
360
250
200
180
160
150
26
0
1
530
270
210
170
150
110
90
28
0
1
430
230
180
150
110
100
90
30
0
1
250
200
150
110
100
90
80
32
1
0
Note 4
1000
740
570
470
410
370
34
1
0
Note 4
990
710
520
420
360
300
36
1
0
Note 4
970
670
480
380
310
230
38
1
0
Note 4
880
560
380
310
270
220
40
1
0
Note 4
800
460
290
240
230
220
42
1
0
1030
680
360
260
220
200
190
44
1
0
790
560
260
220
200
190
170
46
1
0
1110
420
280
210
180
170
140
48
1
0
1110
280
200
190
170
140
120
50
1
0
830
330
200
180
160
130
110
52
1
0
560
340
205
170
140
120
90
54
1
0
510
280
180
140
110
110
90
56
1
0
470
210
160
120
100
90
90
58
1
0
450
220
250
110
90
80
80
60
1
0
430
240
120
90
80
80
70
62
1
1
Note 4
800
580
430
330
250
180
64
1
1
Note 4
720
490
375
285
200
140
66
1
1
Note 4
630
400
320
240
150
100
68
1
1
Note 4
690
365
285
225
170
140
70
1
1
Note 4
650
330
250
210
190
180
72
1
1
Note 4
575
340
250
210
190
170
74
1
1
Note 4
500
355
245
205
180
165
76
1
1
Note 4
550
330
230
200
175
160
78
1
1
Note 4
600
290
220
190
170
155
80
1
1
Note 4
570
240
210
185
165
150
82
1
1
Note 4
540
250
200
180
160
140
Document #: 38-07029 Rev. *F
Page 4 of 12
[+] Feedback
FS781/82/84
Table 4. Modulation Rate Divider Ratios
S1
S0
Input Frequency Range (MHz)
Modulation Divider Number
0
0
6 to 16
120
0
1
16 to 32
240
1
0
32 to 66
480
1
1
66 to 82
720
SSCG Modulation Profile
The digital control inputs S0 and S1 determine the modulation
frequency of FS781/2/4 products. The input frequency is
divided by a fixed number, depending on the operating range
that is selected. The modulation frequency of the FS78x can
be determined from Table 4. To compute the modulation
frequency, determine the values of S0 and S1, and find the
modulation divider number in Table 4.
quently, higher energy peaks. Regulatory agencies test
electronic equipment by the amount of peak energy radiated
from the equipment. By reducing the peak energy at the fundamental and harmonic frequencies, the equipment under test is
able to satisfy agency requirements for EMI. Conventional
methods of reducing EMI have been to use shielding, filtering,
multi-layer PCBs, etc. These FS781/2 and 4 reduce the peak
energy in the clock by increasing the clock bandwidth and
lowering the Q of the clock.
Theory of Operation
SSCG
The FS781/82/84 devices are phase-locked loop-(PLL)-type
clock generators using Direct Digital Synthesis (DDS). ‘By
precisely controlling the bandwidth of the output clock, the
FS781/2/4 products become a low-EMI clock generator. The
theory and detailed operation of these products will be
discussed in the following sections.
The FS781/82/84 products use a unique method of modulating
the clock over a very narrow bandwidth and controlled rate of
change, both peak to peak and cycle to cycle. The FS78x
products take a narrow band digital reference clock in the
range of 6–82 MHz and produce a clock that sweeps between
a controlled start and stop frequency and precise rate of
change. To understand what happens to an SSCG clock,
consider that we have a 20-MHz clock with a 50% duty cycle.
From a 20-MHz clock we know the following:
Clock Frequency = Fc = 20 MHz.
Clock Period = Tc = 1/20 MHz = 50 ns.
EMI
All clocks generate unwanted energy in their harmonics.
Conventional digital clocks are square waves with a duty cycle
that is very close to 50%. Because of the 50/50 duty cycle,
digital clocks generate most of their harmonic energy in the
odd harmonics (e.g., third, fifth, seventh). It is possible to
reduce the amount of energy contained in the fundamental
and harmonics by increasing the bandwidth of the fundamental clock frequency. Conventional digital clocks have a
very high Q factor, which means that all of the energy at that
frequency is concentrated in a very narrow bandwidth, conse-
Consider that this 20-MHz clock is applied to the XIN input of
the FS78x as either an externally driven clock or the result of
a parallel resonant crystal connected to pins 1 and 2 of the
FS78x. Also consider that the products are operating from a
5V DC power supply and the loop filter is set for a total
bandwidth spread of 2%. Refer to Figure 2.
+ .5%
1.0% Xin
Total
- .5%
TIME (microseconds)
Figure 1. Frequency Profile in Time Domain[5]
Note:
5. With the correct loop filter connected to Pin 4, the following profile will provide the best EMI reduction. This profile can be seen on a Time Domain Analyzer.
Document #: 38-07029 Rev. *F
Page 5 of 12
[+] Feedback
FS781/82/84
50%
50%
Tc = 50 ns.
Figure 2. 20-MHz Unmodulated Clock
From the above parameters, the output clock at FSOUT will be
sweeping symmetrically around a center frequency of 20 MHz.
The minimum and maximum extremes of this clock will be
+200 kHz and –200 kHz. So we have a clock that is sweeping
from 19.8 MHz to 20.2 MHz and back again. If we were to look
at this clock on a spectrum analyzer we would see the picture
in Figure 3. Keep in mind that this is a drawing of a perfect
clock with no noise.
Fc = 20 MHz
Fmin =
19.8 MHz
Fmax =
20.2 MHz
Figure 3. Spectrum Analysis of 19.8–20.2 MHz Clock
We see that the original 20-MHz reference clock is at the
center frequency (Cf), and the min. and max. extremes are
positioned symmetrically about the center frequency. This type
of modulation is called Center-Spread. Figure 4 shows a
20-MHz clock as it would be seen on an oscilloscope. The top
trace is the non-modulated reference clock. The bottom trace
is the modulated clock at pin 6. From this comparison chart
you can see that the frequency is decreasing and the period
of each successive clock is increasing. The Tc measurements
on the left and right of the bottom trace indicate the max. and
min. extremes of the clock. Intermediate clock changes are
small and accumulate to achieve the total period deviation.
The reverse of this figure would show the clock going from
minimum extreme back to the high extreme.
Tc =49.50 ns.
Tc = 50.50 n
Figure 4. Period Comparison Chart
Looking at Figure 3, you will note that the peak amplitude of
the 20-MHz non-modulated clock is higher than the wideband
modulated clock. This difference in peak amplitudes between
modulated and unmodulated clocks is the reason why SSCG
clocks are so effective in digital systems. This figure refers to
the fundamental frequency of a clock. A very important characteristic of the SSCG clock is that the bandwidth of the fundamental frequency is multiplied by the harmonic number. In
other words, if the bandwidth of a 20-MHz clock is 200 kHz,
the bandwidth of the third harmonic will be 3 × 200, or 600 kHz.
The amount of bandwidth is relative to the amount of energy
in the clock. Consequently, the wider the bandwidth, the
greater the energy reduction of the clock.
Most applications will not have a problem meeting agency
specifications at the fundamental frequency. It is the higher
harmonics that usually cause the most problems. With an
SSCG clock, the bandwidth and peak energy reduction
increases with the harmonic number. Consider that the
eleventh harmonic of a 20-MHz clock is 220 MHz. With a total
spread of 200 kHz at 20 MHz, the spread at the eleventh
harmonic would be 2.20 MHz, which greatly reduces the peak
energy content. It is typical to see as much as 12- to 18-dB
reduction at the higher harmonics, due to a modulated clock.
The difference in the peak energy of the modulated clock and
the non-modulated clock in typical applications will see a
2 – 3 dB reduction at the fundamental and as much as 8 – 10
dB reduction at the intermediate harmonics: third, fifth,
seventh, etc. At the higher harmonics, it is quite possible to
reduce the peak harmonic energy, compared to the unmodulated clock, by as much as 12 to 18 dB.
Application Notes and Schematic
Figure 5 is configured for the following parameters:
Package selected = FS781.
XIN = 20-MHz crystal
FSOUT = 20 MHz (S0 = 1 and S1 = 0).
Bandwidth of the FSOUT clock is determined by the values of
the loop filter connected to pin 4.
Document #: 38-07029 Rev. *F
Page 6 of 12
[+] Feedback
FS781/82/84
Crystal is 20 MHz is 1st Order
with 18 pF load capacitance.
C2
1
If Crystal load capacitance is
different than 18 pF, C1 and C2
must be re-calculated.
For third overtone crystals, a
parallel or series resonant trap
is required.
20 MHz
27 pF
Xin
VDD
8
0.1 uF
Y1
C3
2
VDD
C1
Xout
S0
7
FS781
(SOIC)
27 pF
3
4
Mount loop filter components as
close to LF pin as possible.
S1
FSOUT
LF
VSS
6
FSOUT
5
R6
C7
C8
**
** Occasionally, C8 is used to
create a second pole for this loop
filter. Refer to Loop Filter Selection
table.
.
Figure 5. FS781 Schematic
Document #: 38-07029 Rev. *F
Page 7 of 12
[+] Feedback
FS781/82/84
Absolute Maximum Ratings[6]
This device contains circuitry to protect the input against
damage due to high static voltages or electric fields; however,
precautions should be taken to avoid application of any
voltage higher than the absolute maximum rated voltages to
this circuit. For proper operation, VIN and VOUT should be
constrained to the range, VSS < (VIN or VOUT) < VDD. All digital
inputs are tied high or low internally. Refers to electrical specifications for operating supply range.
Table 5. Absolute Maximum Ratings
Parameter
Description
Min.
Max.
Unit
VDD
Operating Voltage
3.0
6.0
VDC
VIRvss
Input, relative to VSS
–0.3
VDD + 0.3
VDC
VORvss
Output, relative to VSS
–0.3
VDD + 0.3
VDC
TOP
Temperature, Operating
0
+70
°C
TST
Temperature, Storage
–65
+150
°C
TJ
Temperature, Junction
–
+125
°C
Table 6. DC Electrical Characteristics VDD = 3.3V and 5.0V ±10%, XIN = 48 MHz, TA = 0°C to 70°C
Parameter
Description
Min.
Typ.
Max.
Unit
0.3 * VDD
VDC
VIL
Input Low Voltage
–
VIH
Input High Voltage
0.7 * VDD
IIL
Input Low Current
100
IIH
Input High Current
100
µA
VOL
Output Low Voltage IOL= 10 mA, VDD = 5V
0.4
VDC
VOH
Output High Voltage IOH = 10 mA, VDD = 5V
VOL
Output Low Voltage IOL= 6 mA, VDD = 3.3V
VDC
µA
VDD – 1.0
VDC
0.4
VDC
VOH
Output High Voltage IOH = 5 mA, VDD = 3.3V
2.4
Rpd
Resistor, Pull-down (Pin 7)
60K
125K
200K
Rpu
Resistor, Pull-up (Pin 3)
60K
125K
200K
Cxin
Input Capacitance (Pin 1)
8
Cxout
Output Capacitance (Pin 2)
10
pF
ICC
5V Dynamic Supply Current (CL = No Load)
38
mA
ICC
3.3V Dynamic Supply Current (CL = No Load)
20
mA
ISC
Short Circuit Current (FSOUT)
25
mA
VDC
Ω
Ω
pF
BW
BW% Variations,
3.30V[7]
–20
0
+20
%
BW
BW% Variations, 5.00V[7]
–30
0
+30
%
Table 7. Timing Electrical Characteristics VDD = 3.3V and 5.0V ±10%, TA = 0°C to 70°C, CL = 15 pF, XIN = 48 MHz
Parameter
Description
Min.
Typ.
Max.
Unit
1.8
2.2
2.7
ns
tTLH
Output Rise Time Measured at 10%–90% @ 5 VDC
tTHL
Output Fall Time Measured at 10%–90% @ 5 VDC
1.5
2.0
2.5
ns
tTLH
Output Rise Time Measured at 0.8V–2.0V @ 5 VDC
0.5
0.65
0.8
ns
tTHL
Output Fall Time Measured at 0.8V–2.0 V @ 5 VDC
0.5
0.65
0.8
ns
tTLH
Output Rise Time Measured at 10%–90% @ 3.3 VDC
2.1
2.65
3.2
ns
tTHL
Output Fall Time Measured at 10%–90% @ 3.3 VDC
1.7
2.1
2.6
ns
tTLH
Output Rise Time Measured at 0.8V–2.0V @ 3.3 VDC
0.7
0.95
1.2
ns
tTHL
Output Fall Time Measured at 0.8V–2.0 V @ 3.3 VDC
0.6
0.85
1.1
ns
TsymF1
Output Duty Cycle
45
50
55
%
Notes:
6. Single Power Supply: The Voltage on any input or /O pin cannot exceed the power pin during power-up.
7. Percentage variations from the bandwidth % values given in Table 2 and Table 3.
Document #: 38-07029 Rev. *F
Page 8 of 12
[+] Feedback
FS781/82/84
Table 7. Timing Electrical Characteristics VDD = 3.3V and 5.0V ±10%, TA = 0°C to 70°C, CL = 15 pF, XIN = 48 MHz (continued)
Parameter
Description
Min.
Typ.
Max.
Unit
CCJ
FSOUT, Cycle-to-Cycle Jitter, 48 MHz @ 3.30 VDC (Pin 6)
–
320
370
ps
CCJ
FSOUT, Cycle-to-Cycle Jitter, 48 MHz @ 5.0 VDC (Pin 6)
–
310
360
ps
CCJ
FSOUT, Cycle-to-Cycle Jitter, 72 MHz @ 3.30 VDC (Pin 6)
–
270
325
ps
CCJ
FSOUT, Cycle-to-Cycle Jitter, 72 MHz @ 5.0 VDC (Pin 6)
–
390
440
ps
Table 8. Range Selection Table
S1
(pin 3)
S0
(pin 7)
Fin (MHz)
(pin 2/3)
Modulation
Rate
FS781
FSOUT (pin 6)
FS782
FSOUT (pin 6)
FS784
FSOUT (pin 6)
0
0
6–16
Fin/120
6–16 MHz
12–32 MHz
32–64 MHz
0
1
16–32
Fin/240
16–32 MHz
32–64 MHz
64–82 MHz
1
0
32–66
Fin/480
32–66 MHz
64–82 MHz
N/A
1
1
66–82
Fin/720
66–82 MHz
N/A
N/A
Ordering Information[8]
Part Number
Package Type
Product Flow
IMIFS781BZB
8-pin 150-mil SOIC
Commercial, 0 to 70°C
IMIFS781BZBT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
IMIFS782BZB
8-pin 150-mil SOIC
Commercial, 0 to 70°C
IMIFS782BZBT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
IMIFS784BZB
8-pin 150-mil SOIC
Commercial, 0 to 70°C
IMIFS784BZBT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
IMIFS781BT
8-pin (4.4 mm body) TSSOP
Commercial, 0 to 70°C
IMIFS781BTT
8-pin (4.4 mm body) TSSOP – Tape and Reel
Commercial, 0 to 70°C
IMIFS784BT
8-pin (4.4 mm body) TSSOP
Commercial, 0 to 70°C
IMIFS784BTT
8-pin (4.4 mm body) TSSOP – Tape and Reel
Commercial, 0 to 70°C
8-pin 150-mil SOIC
Commercial, 0 to 70°C
Lead-free
CYIFS781BSXC
CYIFS781BSXCT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
CYIFS782BSXC
8-pin 150-mil SOIC
Commercial, 0 to 70°C
CYIFS782BSXCT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
CYIFS784BSXC
8-pin 150-mil SOIC
Commercial, 0 to 70°C
CYIFS784BSXCT
8-pin 150-mil SOIC – Tape and Reel
Commercial, 0 to 70°C
CYIFS781BZXC
8-pin (4.4 mm body) TSSOP
Commercial, 0 to 70°C
CYIFS781BZXCT
8-pin (4.4 mm body) TSSOP – Tape and Reel
Commercial, 0 to 70°C
CYIFS782BZXC
8-pin (4.4 mm body) TSSOP
Commercial, 0 to 70°C
CYIFS782BZXCT
8-pin (4.4 mm body) TSSOP – Tape and Reel
Commercial, 0 to 70°C
CYIFS784BZXC
8-pin (4.4 mm body) TSSOP
Commercial, 0 to 70°C
CYIFS784BZXCT
8-pin (4.4 mm body) TSSOP – Tape and Reel
Commercial, 0 to 70°C
Note:
8. The ordering part number differs from the marking on the actual device.
Document #: 38-07029 Rev. *F
Page 9 of 12
[+] Feedback
FS781/82/84
Marking Example
Cypress
FS781BT
Date Code, Lot #
Cypress
FS781BS
Date Code, Lot #
FS781 B S
Package
S = SOIC
T = TSSOP
Revision
Cypress Device Driver
Package Drawing and Dimensions
8 Lead (150 Mil) SOIC S08
8-lead (150-Mil) SOIC S8
PIN 1 ID
4
1
1. DIMENSIONS IN INCHES[MM] MIN.
MAX.
2. PIN 1 ID IS OPTIONAL,
ROUND ON SINGLE LEADFRAME
RECTANGULAR ON MATRIX LEADFRAME
0.150[3.810]
0.157[3.987]
3. REFERENCE JEDEC MS-012
0.230[5.842]
0.244[6.197]
4. PACKAGE WEIGHT 0.07gms
PART #
S08.15 STANDARD PKG.
5
SZ08.15 LEAD FREE PKG.
8
0.189[4.800]
0.196[4.978]
0.010[0.254]
0.016[0.406]
SEATING PLANE
X 45°
0.061[1.549]
0.068[1.727]
0.004[0.102]
0.050[1.270]
BSC
0.004[0.102]
0.0098[0.249]
0°~8°
0.016[0.406]
0.035[0.889]
0.0075[0.190]
0.0098[0.249]
51-85066-*C
0.0138[0.350]
0.0192[0.487]
Document #: 38-07029 Rev. *F
Page 10 of 12
[+] Feedback
FS781/82/84
Package Drawing and Dimensions (continued)
8-Lead Thin Shrunk Small Outline Package (4.40 MM Body) Z8
PIN 1 ID
1
DIMENSIONS IN MM[INCHES] MIN.
MAX.
6.25[0.246]
6.50[0.256]
4.30[0.169]
4.50[0.177]
8
0.65[0.025]
BSC.
0.19[0.007]
0.30[0.012]
1.10[0.043] MAX.
0.25[0.010]
BSC
GAUGE
PLANE
0°-8°
0.076[0.003]
0.85[0.033]
0.95[0.037]
0.05[0.002]
0.15[0.006]
2.90[0.114]
3.10[0.122]
SEATING
PLANE
0.50[0.020]
0.70[0.027]
0.09[[0.003]
0.20[0.008]
51-85093-*A
All product and company names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-07029 Rev. *F
Page 11 of 12
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
FS781/82/84
Document History Page
Document Title: FS781/82/84 Low EMI Spectrum Spread Clock
Document Number: 38-07029
REV.
ECN NO.
Issue Date
Orig. of
Change
**
106948
06/07/01
IKA
Convert from IMI to Cypress
*A
111654
02/27/02
IKL
Add new marking suffix for SOIC packages. Converted to FrameMaker.
Description of Change
*B
118355
08/30/02
RGL
Swap the location of S0 and S1 in tables 2 and 3 in pages 2,3 and 4.
*C
122679
12/14/02
RBI
Add power up requirements to operating conditions information.
*D
277189
See ECN
RGL
Added Lead-free Devices
*E
314274
See ECN
RGL
Fixed the Ordering Information to match the DevMaster
*F
417662
See ECN
RGL
Added Maximum Junction Temperature in Absolute Maximum Ratings table
Document #: 38-07029 Rev. *F
Page 12 of 12
[+] Feedback
Similar pages