Cypress CYW312OXC Ftg for viaâ ¢ k7 series chipset with programmable output frequency Datasheet

W312-02
FTG for VIA™ K7 Series Chipset with
Programmable Output Frequency
Features
• Low jitter and tightly controlled clock skew
• Single chip FTG solution for VIA™ K7 Series chipsets
• Programmable clock output frequency with less than
1 MHz increment
• Two pairs of differential CPU clocks
• Eleven copies of PCI clocks
• Three copies of 66-MHz outputs
• Integrated fail-safe Watchdog timer for system
recovery
• Two copies of 48-MHz outputs
• Automatically switch to HW selected or SW
programmed clock frequency when watchdog timer
time-out
• One RESET output for system recovery
• Three copies of 14.31818-MHz reference clocks
• Power management control support
• Capable of generate system RESET after a watchdog
timer time-out occurs or a change in output frequency
via SMBus interface
Key Specifications
• Support SMBus byte read/write and block read/ write
operations to simplify system BIOS development
48-MHz, 3V66, PCI Outputs
Cycle-to-cycle Jitter: .................................................... 500 ps
• Vendor ID and Revision ID support
CPU, 3V66 Output Skew:............................................ 200 ps
• Programmable drive strength for PCI output clocks
48-MHz Output Skew: ................................................. 250 ps
• Programmable output skew between CPU, AGP and PCI
PCI Output Skew:........................................................ 500 ps
CPU Outputs Cycle-to-cycle Jitter: ............................. 250 ps
• Maximized EMI suppression using Cypress’s Spread
Spectrum technology
Block Diagram
Pin Configuration
VDD_REF
X1
X2
XTAL
OSC
PLL REF FREQ
SMBus
Logic
(FS0:4)
VDD_CPU
Divider,
Delay,
and
Phase
Control
Logic
CPUT0,CPUC0
2
CPUT_CS,CPUC_CS
VDD_AGP
AGP0:2
3
VDD_PCI
PCI0/SEL24_48#*
PLL 1
PCI1:8
5
PD#
CPU_STOP#
PCI_STOP#
AGP_STOP#
REF_STOP#
PCI9_E
RST#
VDD_48MHz
48MHz/FS3*
PLL2
24_48MHz/FS4*
/2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
W312-02
SDATA
SCLK
VDD_REF
GND_REF
X1
X2
VDD_48MHz
*FS2/48MHz
*FS3/24_48MHz
GND_48MHz
*FS4/PCI_F
*SEL24_48#/PCI0
PCI1
GND_PCI
PCI2
PCI3
VDD_PCI
PCI4
PCI5
PCI6
GND_PCI
PCI7
PCI8
PCI9_E
VDD_PCI
RST#
REF2
REF1/FS1*
REF0/FS0*
[1]
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
REF0/FS0*
REF1/FS1*
REF2
REF_STOP#*
AGP_STOP#*
GND_CPU
CPUT0
CPUC0
VDD_CPU
CPUT_CS
CPUC_CS
GND_CPU
CPU_STOP#*
PCI_STOP#*
PD#*
VDD_CORE
GND_CORE
SDATA
SCLK
GND_AGP
AGP2
AGP1
AGP0
VDD_AGP
Note:
1. Internal 100K pull-up resistors present on inputs marked with *. Design should not rely solely on internal pull-up resistor to set I/O pins
HIGH.
SEL24_48#*
Cypress Semiconductor Corporation
Document #: 38-07259 Rev. *C
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised April 28, 2005
W312-02
Pin Definitions
I
Pin No.
Pin
Type
REF0/FS0
48
I/O
Reference Clock Output 0/Frequency Select 0: 3.3V 14.318-MHz clock
output. REF0 will be disabled when REF_STOP# is active. This pin also serves
as the select strap to determines device operating frequency as described in
Table 5.
REF1/FS1
47
I/O
Reference Clock Output 0/Frequency Select 1: 3.3V 14.318-MHz clock
output. REF1 will be disabled when REF_STOP# is active. This pin also serves
as the select strap to determines device operating frequency as described in
Table 5.
REF2
46
I/O
Reference Clock Output 2: 3.3V 14.318-MHz clock output. REF2 will be
disabled when REF_STOP# is active.
X1
3
I
Crystal Input: This pin has dual functions. It can be used as an external 14.318MHz crystal connection or as an external reference frequency input.
X2
4
I
Crystal Output: An input connection for an external 14.318-MHz crystal
connection. If using an external reference, this pin must be left unconnected.
PCI_F/FS4
9
I
Free-Running PCI Clock/Frequency Select 4: 3.3V 33-MHz free running PCI
clock output. This pin also serves as the select strap to determines device
operating frequency as described in Table 5.
PCI_0/SEL24_48#
10
I/O
PCI Clock 0/Select 24 or 48 MHz: 3.3V 33-MHz PCI clock outputs. This output
will be disabled when PCI_STOP# is active. This pin also serves as the select
strap to determine device operating frequency of 24_48MHz output.
PCI1:8
11, 13, 14, 16,
17, 18, 20, 21
O
PCI Clock 1 through 8: 3.3V 33-MHz PCI clock outputs. PCI1:8 will be disabled
when PCI_STOP# is active.
PCI9_E
22
O
Early PCI Clock 9: 3.3V 33-MHz PCI clock outputs. PCI9_E will be disabled
when PCI_STOP# is active.
AGP0:2
26, 27, 28
O
AGP Clock 0 through 2: 3.3V 66-MHz clock outputs. The operating frequency
is controlled by FS0:4 (see Table 5). AGP0:2 will be disabled when
AGP_STOP# is active.
48MHz/FS2
6
I/O
48-MHz Output/Frequency Selection 3: 3.3V 48-MHz non-spread spectrum
output. 48MHz will be disabled when REF_STOP# is active. This pin also serves
as the select strap to determine device operating frequency as described in
Table 5.
24_48MHz/FS3
7
I/O
24 or 48-MHz Output/Select 24 or 48 MHz: 3.3V 24 or 48-MHz non-spread
spectrum output. 24_48MHz will be disabled when REF_STOP# is active. This
pin also serves as the select strap to determine device operating frequency as
described in Table 5.
RST#
24
Pin Name
Pin Description
O
Reset#: Open-drain RESET# output.
(opendrain)
CPU Clock Output 0: CPUT0 and CPUC0 are the differential CPU clock
O
(open- outputs for the K7 processor. They are open-drain outputs.
drain)
CPUT0, CPUC0
42, 41
CPUT_CS,
CPUC_CS
39, 38
O
CPU Clock Output for Chipset: CPUT_CS and CPUC_CS are the differential
CPU clock outputs for the chipset. They are push-pull outputs. These outputs
will be disabled when CPU_STOP# is active.
CPU_STOP#
36
I
CPU STOP Input: This input will disable CPUT_CS and CPUC_CS when it is
active.
PCI_STOP#
35
I
PCI STOP Input: This input will disable PCI0:8 and PCI9_E when it is active.
AGP_STOP#
44
I
AGP STOP Input: This input will disable AGP0:2 when it is active.
REF_STOP#
45
I
REF STOP Input: This input will disable REF0:2, 24_48MHz and 48 MHz
outputs when it is active.
Document #: 38-07259 Rev. *C
Page 2 of 20
W312-02
Pin Definitions (continued)
Pin No.
Pin
Type
PD#
34
I
SDATA
31
I/O
Pin Name
Pin Description
Power-Down Input: This input will trigger the clock generator into Power Down
mode when it is active.
Data pin for SMBus circuitry.
SCLK
30
I
Clock pin for SMBus circuitry.
VDD_CPU
40
P
2.5V Power Connection: Power supply for CPU output buffers. Connect to
2.5V.
VDDQ_AGP
25
P
3.3V Power Connection: Power supply for AGP output buffers. Connect to
3.3V.
VDDQ_PCI
15, 23
P
3.3V Power Connection: Power supply for PCI output buffers. Connect to 3.3V.
VDDQ_48MHz
5
P
3.3V Power Connection: Power supply for 48 MHz output buffers. Connect to
3.3V.
VDD_REF
1
P
3.3V Power Connection: Power supply for reference output buffers. Connect
to 3.3V.
VDD_Core
33
P
3.3V Power Connection: Power supply for PLL core. Connect to 3.3V.
2, 8, 29, 32, 37,
43
G
Ground Connections: Connect all ground pins to the common system ground
plane.
GND_REF,
GND_48MHz,
GND_PCI,
GND_AGP,
GND_Core,
GND_CPU
Document #: 38-07259 Rev. *C
Page 3 of 20
W312-02
Serial Data Interface
The W312-02 features a two-pin, serial data interface that can
be used to configure internal register settings that control
particular device functions.
Data Protocol
The clock driver serial protocol supports byte/word write,
byte/word read, block write and block read operations from the
controller. For block write/read operation, the bytes must be
accessed in sequential order from lowest to highest byte with
the ability to stop after any complete byte has been transferred. For byte/word write and byte read operations, system
controller can access individual indexed byte. The offset of the
indexed byte is encoded in the command code.
.The block write and block read protocol is outlined in Table 1
while Table 2 outlines the corresponding byte write and byte
read protocol. The slave receiver address is 11010010 (D2h)
Table 1. Command Code Definitions
Bit
Descriptions
7
0 = Block read or block write operation
1 = Byte/Word read or byte/word write operation
6:0
Byte offset for byte/word read or write operation. For block read or write operations, these bits
need to be set at ‘0000000’.
Table 2. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
2:8
9
10
11:18
19
20:27
28
29:36
37
38:45
Description
Start
Slave address – 7 bits
Write
Acknowledge from slave
Command Code – 8 bits
‘00000000’ stands for block operation
Block Read Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
9
Write
10
Acknowledge from slave
11:18
Command Code – 8 bits
‘00000000’ stands for block operation
Acknowledge from slave
19
Acknowledge from slave
Byte Count – 8 bits
20
Repeat start
Acknowledge from slave
Data byte 0 – 8 bits
Acknowledge from slave
Data byte 1 – 8 bits
46
Acknowledge from slave
...
Data Byte N/Slave Acknowledge...
...
Data Byte N – 8 bits
...
Acknowledge from slave
...
Stop
Document #: 38-07259 Rev. *C
21:27
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
38
39:46
47
48:55
Byte count from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
56
Acknowledge
...
Data bytes from slave/Acknowledge
...
Data byte N from slave – 8 bits
...
Not Acknowledge
...
Stop
Page 4 of 20
W312-02
Table 3. Word Read and Word Write Protocol
Word Write Protocol
Bit
1
2:8
Description
Start
Word Read Protocol
Bit
1
Slave address – 7 bits (D2)
2:8
Description
Start
Slave address – 7 bits (D3)
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
28
29:36
Command Code – 8 bits
‘1xxxxxxx’ stands for byte or word operation
bit[6:0] of the command code represents the
offset of the byte to be accessed
Acknowledge from slave
Data byte low – 8 bits
Acknowledge from slave
11:18
19
20
21:27
Command Code – 8 bits
‘1xxxxxxx’ stands for byte or word operation
bit[6:0] of the command code represents the
offset of the byte to be accessed
Acknowledge from slave
Repeat start
Slave address – 7 bits
Data byte high – 8 bits
28
Read
37
Acknowledge from slave
29
Acknowledge from slave
38
Stop
30:37
38
39:46
Data byte low from slave – 8 bits
Acknowledge
Data byte high from slave – 8 bits
47
NOT acknowledge
48
Stop
Table 4. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
Byte Read Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation
bit[6:0] of the command code represents the
offset of the byte to be accessed
Acknowledge from slave
Data byte – 8 bits
28
Acknowledge from slave
29
Stop
11:18
19
20
21:27
Acknowledge from slave
Repeat start
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
Document #: 38-07259 Rev. *C
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation
bit[6:0] of the command code represents the
offset of the byte to be accessed
Data byte from slave – 8 bits
38
Not Acknowledge
39
Stop
Page 5 of 20
W312-02
W312-02 Serial Configuration Map
1. The serial bits will be read by the clock driver in the following
order:
Byte 0 - Bits 7, 6, 5, 4, 3, 2, 1, 0
2. All unused register bits (reserved and N/A) should be
written to a “0” level.
3. All register bits labeled “Initialize to 0" must be written to
zero during initialization.
Byte 1 - Bits 7, 6, 5, 4, 3, 2, 1, 0
Byte N - Bits 7, 6, 5, 4, 3, 2, 1, 0
Byte 0: Control Register 0
Bit
Pin#
Name
Default
Description
Bit 7
–
Spread Enable
0
0 = Disabled
Bit 6
–
Spread Select2
0
‘000’ = ±0.25%
Bit 5
–
Spread Select1
0
‘001’ = –0.5%
Bit 4
–
Spread Select0
0
‘010’ = ±0.5%
1 = Enabled
‘011’ = ±0.38%
‘100’ = Reserved
‘101’ = Reserved
‘110’ = Reserved
‘111’ = Reserved
Bit 3
–
SEL3
0
Bit 2
–
SEL2
0
Bit 1
–
SEL1
0
Bit 0
–
SEL0
0
SW Frequency selection bits. See Table 5.
Byte 1: Control Register 1
Bit
Pin#
Name
Default
Description
Bit 7
42, 41
CPUT0, CPUC0
1
(Active/Inactive)
Bit 6
39, 38
CPUT_CS,
CPUC_CS
1
(Active/Inactive)
Bit 5
6
48MHz
1
(Active/Inactive)
Bit 4
7
24_48MHz
1
(Active/Inactive)
Bit 3
–
Reserved
0
Reserved
Bit 2
28
AGP2
1
(Active/Inactive)
Bit 1
27
AGP1
1
(Active/Inactive)
Bit 0
26
AGP0
1
(Active/Inactive)
Byte 2: Control Register 2
Bit
Pin#
Name
Default
Description
Bit 7
20
PCI7
1
(Active/Inactive)
Bit 6
18
PCI6
1
(Active/Inactive)
Bit 5
17
PCI5
1
(Active/Inactive)
Bit 4
16
PCI4
1
(Active/Inactive)
Bit 3
14
PCI3
1
(Active/Inactive)
Bit 2
13
PCI2
1
(Active/Inactive)
Bit 1
11
PCI1
1
(Active/Inactive)
Bit 0
10
PCI0
1
(Active/Inactive)
Document #: 38-07259 Rev. *C
Page 6 of 20
W312-02
\
Byte 3: Control Register
Bit
Pin#
Name
Default
Description
Bit 7
9
PCI_F
1
(Active/Inactive)
Bit 6
22
PCI9_E
1
(Active/Inactive)
Bit 5
–
Reserved
0
Reserved
Bit 4
21
PCI8
1
(Active/Inactive)
Bit 3
46
REF2
1
(Active/Inactive)
Bit 2
–
Reserved
0
Reserved
Bit 1
47
REF1
1
(Active/Inactive)
Bit 0
48
REF0
1
(Active/Inactive)
Byte 4: Watchdog Timer Register
Bit
Pin#
Name
Default
Description
Bit 7
–
Reserved
0
Reserved
Bit 6
–
FS_Override
0
0 = Select operating frequency by FS[4:0] input pins
1 = Select operating frequency by SEL[4:0] settings
Bit 5
–
WD_TIMER4
1
Bit 4
–
WD_TIMER3
1
Bit 3
–
WD_TIMER2
1
Bit 2
–
WD_TIMER1
1
Bit 1
–
WD_TIMER0
1
These bits store the time-out value of the Watchdog
timer. The scale of the timer is determine by the
prescaler.
The timer can support a value of 150 ms to 4.8 sec
when the prescaler is set to 150 ms. If the prescaler is
set to 2.5 sec, it can support a value from 2.5 sec to 80
sec.
When the Watchdog timer reaches “0”, it will set the
WD_TO_STATUS bit.
Bit 0
–
WD_PRE_SCAL
ER
0
0 = 150 ms
1 = 2.5 sec
Byte 5: Control Register 5
Bit
Pin#
Name
Default
Description
Bit 7
9
Latched FS4 input
X
Bit 6
7
Latched FS3 input
X
Bit 5
6
Latched FS2 input
X
Bit 4
47
Latched FS1 input
X
Bit 3
48
Latched FS0 input
X
Bit 2
–
Reserved
0
Reserved
Bit 1
–
Reserved
0
Reserved
Bit 0
–
SEL4
0
SW Frequency selection bits. See Table 5.
Document #: 38-07259 Rev. *C
Latched FS[4:0] inputs. These bits are read only.
Page 7 of 20
W312-02
Byte 6: Reserved Register
Bit
Name
Default
Pin Description
Bit 7
Reserved
1
Reserved
Bit 6
Reserved
1
Reserved
Bit 5
Reserved
1
Reserved
Bit 4
Reserved
1
Reserved
Bit 3
Reserved
1
Reserved
Bit 2
Reserved
1
Reserved
Bit 1
Reserved
1
Reserved
Bit 0
Reserved
1
Reserved
Byte 7: Reserved Register
Bit
Name
Default
Pin Description
Bit 7
Reserved
1
Reserved
Bit 6
Reserved
1
Reserved
Bit 5
Reserved
1
Reserved
Bit 4
Reserved
1
Reserved
Bit 3
Reserved
1
Reserved
Bit 2
Reserved
1
Reserved
Bit 1
Reserved
1
Reserved
Bit 0
Reserved
1
Reserved
Byte 8: Vendor ID and Revision ID Register (Read Only)
Bit
Name
Default
Pin Description
Bit 7
Revision_ID3
0
Revision ID bit[3]
Bit 6
Revision_ID2
0
Revision ID bit[2]
Bit 5
Revision_ID1
0
Revision ID bit[1]
Bit 4
Revision_ID0
0
Revision ID bit[0]
Bit 3
Vendor_ID3
1
Bit[3] of Cypress Semiconductor’s Vendor ID. This bit is read only.
Bit 2
Vendor_ID2
0
Bit[2] of Cypress Semiconductor’s Vendor ID. This bit is read only.
Bit 1
Vendor _ID1
0
Bit[1] of Cypress Semiconductor’s Vendor ID. This bit is read only.
Bit 0
Vendor _ID0
0
Bit[0] of Cypress Semiconductor’s Vendor ID. This bit is read only.
Document #: 38-07259 Rev. *C
Page 8 of 20
W312-02
Byte 9: System Reset and Watchdog Timer Register
Bit
Name
Default
Pin Description
Bit 7
Reserved
0
Reserved
Bit 6
PCI_DRV
0
PCI clock output drive strength
0 = Normal
1 = High Drive
Bit 5
Reserved
0
Reserved
Bit 4
RST_EN_WD
0
This bit will enable the generation of a Reset pulse when a watchdog timer timeout occurs.
0 = Disabled
1 = Enabled
Bit 3
RST_EN_FC
0
This bit will enable the generation of a Reset pulse after a frequency change
occurs.
0 = Disabled
1 = Enabled
Bit 2
WD_TO_STATUS
0
Watchdog Timer Time-out Status bit
0 = No time-out occurs (READ); Ignore (WRITE)
1 = time-out occurred (READ); Clear WD_TO_STATUS (WRITE)
Bit 1
WD_EN
0
0 = Stop and re-load Watchdog timer
1 = Enable Watchdog timer. It will start counting down after a frequency change
occurs.
Bit 0
Reserved
0
Reserved
Byte 10: Skew Control Register
Bit
Name
Default
Description
Bit 7
CPU_Skew2
0
Bit 6
CPU_Skew1
0
Bit 5
CPU_Skew0
0
Bit 4
Reserved
0
Reserved
Bit 3
PCI_Skew1
0
Bit 2
PCI_Skew0
0
PCI skew control
00 = Normal
01 = –500 ps
10 = Reserved
11 = +500 ps
Bit 1
AGP_Skew1
0
Bit 0
AGP_Skew0
0
Document #: 38-07259 Rev. *C
CPU skew control
000 = Normal
001 = –150 ps
010 = –300 ps
011 = –450 ps
100 = +150 ps
101 = +300 ps
110 = +450 ps
111 = +600 ps
AGP skew control
00 = Normal
01 = –150 ps
10 = +150 ps
11 = +300 ps
Page 9 of 20
W312-02
Byte 11: Recovery Frequency N - Value Register
Bit
Name
Default
Pin Description
If ROCV_FREQ_SEL is set, W312-02 will use the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] to determine the recovery
CPU output frequency.when a Watchdog timer time-out occurs.
The setting of FS_Override bit determines the frequency ratio for CPU, SDRAM,
AGP and SDRAM. When it is cleared, W312-02 will use the same frequency
ratio stated in the Latched FS[4:0] register. When it is set,
W312-02 will use the frequency ratio stated in the SEL[4:0] register.
W312-02 supports programmable CPU frequency ranging from 50 MHz to 248
MHz.
W312-02 will change the output frequency whenever there is an update to either
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0]. Therefore, it is recommended
to use Word or Block write to update both registers within the same SMBus bus
operation.
Bit 7
ROCV_FREQ_N7
0
Bit 6
ROCV_FREQ_N6
0
Bit 5
ROCV_FREQ_N5
0
Bit 4
ROCV_FREQ_N4
0
Bit 3
ROCV_FREQ_N3
0
Bit 2
ROCV_FREQ_N2
0
Bit 1
ROCV_FREQ_N1
0
Bit 0
ROCV_FREQ_N0
0
Byte 12: Recovery Frequency M- Value Register
Bit
Bit 7
Name
Default
Pin Description
ROCV_FREQ_SEL
0
ROCV_FREQ_SEL determines the source of the recover frequency when a
Watchdog timer time-out occurs. The clock generator will automatically switch
to the recovery CPU frequency based on the selection on ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] & ROCV_FREQ_M[6:0]
If ROCV_FREQ_SEL is set, W312-02 will use the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] to determine the recovery
CPU output frequency.when a Watchdog timer time-out occurs
The setting of FS_Override bit determines the frequency ratio for CPU,
SDRAM, AGP and SDRAM. When it is cleared, W312-02 will use the same
frequency ratio stated in the Latched FS[4:0] register. When it is set, W312-02
will use the frequency ratio stated in the SEL[4:0] register.
W312-02 supports programmable CPU frequency ranging from 50 MHz to 248
MHz.
W312-02 will change the output frequency whenever there is an update to
either ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0]. Therefore, it is recommended to use Word or Block write to update both registers within the same
SMBus bus operation.
Bit 6
ROCV_FREQ_M6
0
Bit 5
ROCV_FREQ_M5
0
Bit 4
ROCV_FREQ_M4
0
Bit 3
ROCV_FREQ_M3
0
Bit 2
ROCV_FREQ_M2
0
Bit 1
ROCV_FREQ_M1
0
Bit 0
ROCV_FREQ_M0
0
Byte 13: Programmable Frequency Select N-Value Register
Bit
Name
Default
Pin Description
If Prog_Freq_EN is set, W300 will use the values programmed in
CPU_FSEL_N[7:0] and CPU_FSEL_M[6:0] to determine the CPU output
frequency. The new frequency will start to load whenever CPU_FSELM[6:0] is
updated.
The setting of FS_Override bit determines the frequency ratio for CPU, SDRAM,
AGP and SDRAM. When it is cleared, W312 will use the same frequency ratio
stated in the Latched FS[4:0] register. When it is set, W312-02 will use the
frequency ratio stated in the SEL[4:0] register.
W312-02 supports programmable CPU frequency ranging from 50 MHz to 248
MHz.
Bit 7
CPU_FSEL_N7
0
Bit 6
CPU_FSEL_N6
0
Bit 5
CPU_FSEL_N5
0
Bit 4
CPU_FSEL_N4
0
Bit 3
CPU_FSEL_N3
0
Bit 2
CPU_FSEL_N2
0
Bit 1
CPU_FSEL_N1
0
Bit 0
CPU_FSEL_N0
0
Document #: 38-07259 Rev. *C
Page 10 of 20
W312-02
Byte 14: Programmable Frequency Select N-Value Register
Bit
Name
Default
Description
Bit 7
Pro_Freq_EN
0
Programmable output frequencies enabled
0 = disabled
1 = enabled
Bit 6
CPU_FSEL_M6
0
Bit 5
CPU_FSEL_M5
0
Bit 4
CPU_FSEL_M4
0
Bit 3
CPU_FSEL_M3
0
Bit 2
CPU_FSEL_M2
0
Bit 1
CPU_FSEL_M1
0
Bit 0
CPU_FSEL_M0
0
If Prog_Freq_EN is set, W300 will use the values programmed in
CPU_FSEL_N[7:0] and CPU_FSEL_M[6:0] to determine the CPU output
frequency. The new frequency will start to load whenever CPU_FSELM[6:0] is
updated.
The setting of FS_Override bit determines the frequency ratio for CPU, SDRAM,
AGP and SDRAM. When it is cleared, W312-02 will use the same frequency
ratio stated in the Latched FS[4:0] register. When it is set, W312-02 will use the
frequency ratio stated in the SEL[4:0] register.
W312-02 supports programmable CPU frequency ranging from 50 MHz to 248
MHz.
Byte 15: Reserved Register
Bit
Pin#
Name
Default
Description
Bit 7
–
Reserved
0
Reserved
Bit 6
–
Reserved
0
Reserved
Bit 5
–
Reserved
0
Reserved
Bit 4
–
Reserved
0
Reserved
Bit 3
–
Reserved
0
Reserved
Bit 2
–
Reserved
0
Reserved
Bit 1
–
Reserved
1
Reserved. Write with ‘1’
Bit 0
–
Reserved
1
Reserved. Write with ‘1’
Byte 16: Reserved Register
Bit
Pin#
Name
Default
Description
Bit 7
–
Reserved
0
Reserved
Bit 6
–
Reserved
0
Reserved
Bit 5
–
Reserved
0
Reserved
Bit 4
–
Reserved
0
Reserved
Bit 3
–
Reserved
0
Reserved
Bit 2
–
Reserved
0
Reserved
Bit 1
–
Reserved
0
Reserved
Byte 17: Reserved Register
Bit
Pin#
Name
Default
Description
Bit 7
–
Reserved
0
Reserved
Bit 6
–
Reserved
0
Reserved
Bit 5
–
Reserved
0
Reserved
Bit 4
–
Reserved
0
Reserved
Bit 3
–
Reserved
0
Reserved
Bit 2
–
Reserved
0
Reserved
Bit 1
–
Reserved
0
Reserved
Document #: 38-07259 Rev. *C
Page 11 of 20
W312-02
Table 5. Additional Frequency Selections through Serial Data Interface Data Bytes
Input Conditions
Output Frequency
FS4
FS3
FS2
FS1
FS0
SEL4
SEL3
SEL2
SEL1
SEL0
CPU
3V66
PCI
PLL Gear
Constants
(G)
0
0
0
0
0
156.0
78.0
39.0
48.00741
0
0
0
0
1
154.0
77.0
38.5
48.00741
0
0
0
1
0
152.0
76.0
38.0
48.00741
0
0
0
1
1
147.0
73.5
36.8
48.00741
0
0
1
0
0
144.0
72.0
36.0
48.00741
0
0
1
0
1
142.0
71.0
35.5
48.00741
0
0
1
1
0
138.0
69.0
34.5
48.00741
0
0
1
1
1
136.0
68.0
34.0
48.00741
0
1
0
0
0
124.0
62.0
31.0
48.00741
0
1
0
0
1
122.0
61.0
30.5
48.00741
0
1
0
1
0
117.0
78.0
39.0
48.00741
0
1
0
1
1
115.0
76.7
38.3
48.00741
0
1
1
0
0
113.0
75.3
37.7
48.00741
0
1
1
0
1
108.0
72.0
36.0
48.00741
0
1
1
1
0
105.0
70.0
35.0
48.00741
0
1
1
1
1
102.0
68.0
34.0
48.00741
1
0
0
0
0
Reserved
Reserved
Reserved
Reserved
1
0
0
0
1
Reserved
Reserved
Reserved
Reserved
1
0
0
1
0
Reserved
Reserved
Reserved
Reserved
1
0
0
1
1
200.0
66.6
33.3
48.00741
1
0
1
0
0
190.0
76.0
38.0
48.00741
1
0
1
0
1
180.0
72.0
36.0
48.00741
1
0
1
1
0
170.0
68.0
34.0
48.00741
1
0
1
1
1
150.0
75.0
37.5
48.00741
1
1
0
0
0
140.0
70.0
35.0
48.00741
1
1
0
0
1
120.0
60.0
30.0
48.00741
1
1
0
1
0
110.0
73.3
33.3
48.00741
1
1
0
1
1
66.6
66.6
33.3
48.00741
1
1
1
0
0
200.0
66.6
33.3
48.00741
1
1
1
0
1
166.6
66.6
33.3
48.00741
1
1
1
1
0
100.0
66.6
33.3
48.00741
1
1
1
1
1
133.3
66.6
33.3
48.00741
Programmable Output Frequency, Watchdog Timer and
Recovery Output Frequency Functional Description
The Programmable Output Frequency feature allows users to
generate any CPU output frequency from the range of 50 MHz
to 248 MHz. Cypress offers the most dynamic and the simplest
programming interface for system developers to utilize this
feature in their platforms.
Document #: 38-07259 Rev. *C
The Watchdog Timer and Recovery Output Frequency
features allow users to implement a recovery mechanism
when the system hangs or getting unstable. System BIOS or
other control software can enable the Watchdog timer before
they attempt to make a frequency change. If the system hangs
and a Watchdog timer time-out occurs, a system reset will be
generated and a recovery frequency will be activated.
All of the related registers are summarized inTable 7.
Page 12 of 20
W312-02
Table 6. Register Summary
Name
Pro_Freq_EN
Description
Programmable output frequencies enabled
0 = Disabled (default)
1 = Enabled
When it is disabled, the operating output frequency will be determined by either the latched value of
FS[4:0] inputs or the programmed value of SEL[4:0]. If FS_Override bit is clear, latched FS[4:0] inputs
will be used. If FS_Override bit is set, programmed value of SEL[4:0] will be used.
When it is enabled, the CPU output frequency will be determined by the programmed value of
CPUFSEL_N, CPUFSEL_M and the PLL Gear Constant. The program value of FS_Override, SEL[4:0]
or the latched value of FS[4:0] will determine the PLL Gear Constant and the frequency ratio between
CPU and other frequency outputs
FS_Override
When Pro_Freq_EN is cleared or disabled,
0 = Select operating frequency by FS input pins (default)
1 = Select operating frequency by SEL bits in SMBus control bytes
When Pro_Freq_EN is set or enabled,
0 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the latched value of FS input pins (default)
1 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the programmed value of SEL bits in SMBus control bytes
CPU_FSEL_N,
CPU_FSEL_M
When Prog_Freq_EN is set or enabled, the values programmed in CPU_FSEL_N[7:0] and
CPU_FSEL_M[6:0] determines the CPU output frequency. The new frequency will start to load
whenever there is an update to either CPU_FSEL_N[7:0] or CPU_FSEL_M[6:0]. Therefore, it is recommended to use Word or Block write to update both registers within the same SMBus bus operation.
The setting of FS_Override bit determines the frequency ratio for CPU, AGP and PIC. When
FS_Override is cleared or disabled, the frequency ratio follows the latched value of the FS input pins.
When FS_Override is set or enabled, the frequency ratio follows the programmed value of SEL bits in
SMBus control bytes.
ROCV_FREQ_SEL
ROCV_FREQ_SEL determines the source of the recover frequency when a Watchdog timer time-out
occurs. The clock generator will automatically switch to the recovery CPU frequency based on the
selection on ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] & ROCV_FREQ_M[6:0]
ROCV_FREQ_N[7:0],
ROCV_FREQ_M[6:0]
When ROCV_FREQ_SEL is set, the values programmed in ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0] will be used to determine the recovery CPU output frequency when a
Watchdog timer time-out occurs
The setting of FS_Override bit determines the frequency ratio for CPU, AGP and PIC. When it is cleared,
the same frequency ratio stated in the Latched FS[4:0] register will be used.
When it is set, the frequency ratio stated in the SEL[4:0] register will be used.
The new frequency will start to load whenever there is an update to either ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0]. Therefore, it is recommended to use Word or Block write to update both registers
within the same SMBus bus operation.
WD_EN
0 = Stop and reload Watchdog timer
1 = Enable Watchdog timer. It will start counting down after a frequency change occurs.
WD_TO_STATUS
Watchdog Timer Time-out Status bit
0 = No time-out occurs (READ); Ignore (WRITE)
1 = time-out occurred (READ); Clear WD_TO_STATUS (WRITE)
WD_TIMER[4:0]
These bits store the time-out value of the Watchdog timer. The scale of the timer is determine by the
prescaler.
The timer can support a value of 150 ms to 4.8 sec when the pre-scaler is set to 150 ms. If the prescaler is set to 2.5 sec, it can support a value from 2.5 sec to 80 sec.
When the Watchdog timer reaches “0”, it will set the WD_TO_STATUS bit.
WD_PRE_SCALER
0 = 150 ms
1 = 2.5 sec
Document #: 38-07259 Rev. *C
Page 13 of 20
W312-02
Table 6. Register Summary (continued)
Name
Description
RST_EN_WD
This bit will enable the generation of a Reset pulse when a Watchdog timer time-out occurs.
0 = Disabled
1 = Enabled
RST_EN_FC
This bit will enable the generation of a Reset pulse after a frequency change occurs.
0 = Disabled
1 = Enabled
How to Program CPU Output Frequency
When the programmable output frequency feature is enabled
(Pro_Freq_EN bit is set), the CPU output frequency is determined by the following equation:
Fcpu = G * (N+3)/(M+3)
“N” and “M” are the values programmed in Programmable
Frequency Select N-Value Register and M-Value Register,
respectively.
“G” stands for the PLL Gear Constant, which is determined by
the programmed value of FS[4:0] or SEL[4:0]. The value is
listed in Table 5. The ratio of (N+3) and (M+3) need to be
greater than “1” [(N+3)/(M+3) > 1].
Table 7 lists set of N and M values for different frequency
output ranges.This example use a fixed value for the M-Value
Register and select the CPU output frequency by changing the
value of the N-Value Register.
Table 7. Examples of N and M Value for Different CPU Frequency Range
Frequency Ranges
Gear Constants
Fixed Value for
M-Value Register
Range of N-Value Register
for Different CPU Frequency
50 MHz–129 MHz
48.00741
93
97–255
130 MHz–248 MHz
48.00741
48
127–245
Document #: 38-07259 Rev. *C
Page 14 of 20
W312-02
Absolute Maximum Ratings[2]
Stresses greater than those listed in this table may cause
permanent damage to the device. These represent a stress
rating only. Operation of the device at these or any other condi-
tions above those specified in the operating sections of this
specification is not implied. Maximum conditions for extended
periods may affect reliability.
.
Parameter
Description
Rating
Unit
VDD, VIN
Voltage on any pin with respect to GND
–0.5 to +7.0
V
TSTG
Storage Temperature
–65 to +150
°C
TB
Ambient Temperature under Bias
–55 to +125
°C
TA
Operating Temperature
0 to +70
°C
ESDPROT
Input ESD Protection
2 (min.)
kV
DC Electrical Characteristics: TA = 0°C to +70°C, VDD = 3.3V±5% and 2.5V±5%
Parameter
Description
Test Condition
Min.
Typ.
Max.
Unit
Supply Current
IDD
3.3V Supply Current
CPU =100 MHz
Outputs Loaded[3]
260
mA
IDD
2.5V Supply Current
CPUCS =100 MHz
Outputs Loaded[3]
25
mA
Logic Inputs
VIL
Input Low Voltage
GND – 0.3
0.8
V
VIH
Input High Voltage
2.0
IIL
IIH
VDD + 0.3
V
Input Low
Current[4]
–25
µA
Input High
Current[4]
10
µA
50
mV
Clock Outputs
VOL
Output Low Voltage
IOL = 1 mA
VOH
Output High Voltage
IOH = –1 mA
VOL
Output Low Voltage
CPUT_CS,
CPUC_CS,
CPUT0, CPUC0
Termination to V pull-up
(external)
0
0.3
V
VOH
Output High Voltage
CPUT_CS,
CPUC_CS,
CPUT0, CPUC0
Termination to V pull-up
(external)
1.0
1.2
V
IOL
Output Low Current
PCI, AGP
VOL = 1.5V
70
110
135
mA
REF
VOL = 1.5V
50
70
100
mA
48 MHz
VOL = 1.5V
50
70
100
mA
24_48 MHz
VOL = 1.5V
50
70
100
mA
PCI, AGP
VOH = 1.5V
70
110
135
mA
REF
VOH = 1.5V
50
70
100
mA
48 MHz
VOH = 1.5V
50
70
100
mA
24_48 MHz
VOH = 1.5V
50
70
100
mA
IOH
Output High Current
3.1
V
Notes:
2. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
3. All clock outputs loaded with 6" 60Ω transmission lines with 20-pF capacitors.
4. X1 input threshold voltage (typical) is VDD/2.
Document #: 38-07259 Rev. *C
Page 15 of 20
W312-02
DC Electrical Characteristics: TA = 0°C to +70°C, VDD = 3.3V±5% and 2.5V±5% (continued)
Parameter
Description
Test Condition
Min.
Typ.
Max.
Unit
Crystal Oscillator
VTH
X1 Input Threshold Voltage[4]
CLOAD
Load Capacitance, Imposed on
External Crystal[5]
CIN,X1
X1 Input Capacitance[6]
VDD = 3.3V
Pin X2 unconnected
1.65
V
18
pF
TBD
pF
Pin Capacitance/Inductance
CIN
Input Pin Capacitance
5
pF
COUT
Output Pin Capacitance
Except X1 and X2
6
pF
LIN
Input Pin Inductance
7
nH
AC Electrical Characteristics
TA = 0°C to +70°C, VDDQ3 = 3.3V±5%, fXTL = 14.31818 MHz
AC clock parameters are tested and guaranteed over stated operating conditions using the stated lump capacitive load at the
clock output; Spread Spectrum is disabled.
CPU Clock Outputs (CPUT0, CPUC0, CPU_CS)[7]
CPU = 100 MHz
Parameter
Description
Test Condition/Comments
Min.
Typ. Max.
CPU = 133 MHz
Min.
Typ.
Max.
Unit
tR
Output Rise Edge Rate CPU_CS
1.0
4.0
1.0
4.0
V/ns
tF
Output Fall Edge Rate
CPU_CS
1.0
4.0
1.0
4.0
V/ns
tD
Duty Cycle
Measured at 50% point
45
55
45
tJC
Jitter, Cycle to Cycle
fST
Frequency Stabilization Assumes full supply voltage reached
within 1 ms from power-up. Short
from Power-up (cold
cycles exist prior to frequency
start)
stabilization.
3
3
ms
Zo
AC Output Impedance
50
50
Ω
250
VO = VX
55
%
250
ps
Notes:
5. The W312-02 contains an internal crystal load capacitor between pin X1 and ground and another between pin X2 and ground. Total load placed on crystal is
18 pF; this includes typical stray capacitance of short PCB traces to crystal.
6. X1 input capacitance is applicable when driving X1 with an external clock source (X2 is left unconnected).
7. Refer to Figure 1 for K7 operation clock driver test circuit.
Document #: 38-07259 Rev. *C
Page 16 of 20
W312-02
PCI Clock Outputs (Lump Capacitance Test Load = 30 pF)
Parameter
Description
Test Condition/Comments
Min.
Typ.
Max.
Unit
tP
Period
Measured on rising edge at 1.5V
30
ns
tH
High Time
Duration of clock cycle above 2.4V
12
ns
tL
Low Time
Duration of clock cycle below 0.4V
12
ns
tR
Output Rise Edge Rate
Measured from 0.4V to 2.4V
1
4
V/ns
tF
Output Fall Edge Rate
Measured from 2.4V to 0.4V
1
4
V/ns
tD
Duty Cycle
Measured on rising and falling edge at 1.5V
45
55
%
tJC
Jitter, Cycle-to-Cycle
Measured on rising edge at 1.5V. Maximum
difference of cycle time between two adjacent cycles.
250
ps
tSK
Output Skew
Measured on rising edge at 1.5V
500
ps
tO
CPU to PCI Clock Skew
Covers all CPU/PCI outputs. Measured on rising edge
at 1.5V. CPU leads PCI output.
4
ns
fST
Frequency Stabilization
Assumes full supply voltage reached within 1 ms from
from Power-up (cold start) power-up. Short cycles exist prior to frequency stabilization.
3
ms
Zo
AC Output Impedance
1.5
Average value during switching transition. Used for
determining series termination value.
Ω
30
REF Clock Outputs (Lump Capacitance Test Load = 20 pF)
Parameter
Description
Test Condition/Comments
Min.
Typ.
Max.
14.318
Unit
f
Frequency, Actual
Frequency generated by crystal oscillator
tR
Output Rise Edge Rate
Measured from 0.4V to 2.4V
0.5
2
V/ns
tF
Output Fall Edge Rate
Measured from 2.4V to 0.4V
0.5
2
V/ns
tD
Duty Cycle
Measured on rising and falling edge at 1.5V
45
55
%
fST
Frequency Stabilization from Assumes full supply voltage reached within 1 ms
Power-up (cold start)
from power-up. Short cycles exist prior to
frequency stabilization.
3
ms
Zo
AC Output Impedance
Average value during switching transition. Used
for determining series termination value.
MHz
Ω
40
48-MHz Clock Output (Lump Capacitance Test Load = 20 pF)
Parameter
Description
Test Condition/Comments
f
Frequency, Actual
Determined by PLL divider ratio (see m/n below)
Min.
Typ.
Max.
Unit
48.008
MHz
ppm
fD
Deviation from 48 MHz
(48.008 – 48)/48
+167
m/n
PLL Ratio
(14.31818 MHz x 57/17 = 48.008 MHz)
57/17
tR
Output Rise Edge Rate
Measured from 0.4V to 2.4V
0.5
2
V/ns
tF
Output Fall Edge Rate
Measured from 2.4V to 0.4V
0.5
2
V/ns
tD
Duty Cycle
Measured on rising and falling edge at 1.5V
45
55
%
fST
Frequency Stabilization
from Power-up (cold start)
Assumes full supply voltage reached within 1 ms
from power-up. Short cycles exist prior to
frequency stabilization.
3
ms
Zo
AC Output Impedance
Average value during switching transition. Used
for determining series termination value.
Document #: 38-07259 Rev. *C
40
Ω
Page 17 of 20
W312-02
24-MHz Clock Output (Lump Capacitance Test Load = 20 pF)
Parameter
Description
Test Condition/Comments
Min.
f
Frequency, Actual
Determined by PLL divider ratio (see m/n below)
Typ.
Max.
Unit
24.004
MHz
ppm
fD
Deviation from 24 MHz
(24.004 – 24)/24
+167
m/n
PLL Ratio
(14.31818 MHz x 57/34 = 24.004 MHz)
57/34
tR
Output Rise Edge Rate
Measured from 0.4V to 2.4V
0.5
2
V/ns
tF
Output Fall Edge Rate
Measured from 2.4V to 0.4V
0.5
2
V/ns
tD
Duty Cycle
Measured on rising and falling edge at 1.5V
45
55
%
fST
Frequency Stabilization
from Power-up (cold start)
Assumes full supply voltage reached within 1 ms
from power-up. Short cycles exist prior to
frequency stabilization.
3
ms
Zo
AC Output Impedance
Average value during switching transition. Used
for determining series termination value.
40
Ω
VDD
+ V1
1.5V
3.3
-
R8
CPUCLK_T
Z0 = 52Ω
Length = 5”
T1
R1
68
Z0 = 52Ω
Length = 3”
T2
47
20p
1.5V
Clock Chip
CPUDriver
R3
68
R9
CPUCLK_C
Z0 = 52Ω
Length = 5”
T4
Z0 = 52Ω
Length = 3”
T5
47
20p
Figure 1. K7 Open Drain Clock Driver Test Circuit
Ordering Information
Ordering Code
Package Type
Product Flow
W312-02H
48-pin SSOP
Commercial, 0°C to 70°C
W312-02HT
48-pin SSOP - Tape and Reel
Commercial, 0°C to 70°C
CYW312OXC
48-pin SSOP
Commercial, 0°C to 70°C
CYW312OXCT
48-pin SSOP - Tape and Reel
Commercial, 0°C to 70°C
Lead-free
Document #: 38-07259 Rev. *C
Page 18 of 20
W312-02
Package Drawing and Dimension
48-Lead Shrunk Small Outline Package O48
51-85061-*C
VIA is a trademark of VIA Technologies, Inc. All product and company names mentioned in this document may be the trademarks
of their respective holders.
Document #: 38-07259 Rev. *C
Page 19 of 20
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
W312-02
Document History Page
Document Title: W312-02 FTG for VIA™ K7 Series Chipset with Programmable Output Frequency
Document Number: 38-07259
REV.
ECN NO.
Issue
Date
Orig. of
Change
Description of Change
**
110524
01/07/02
SZV
Change from Spec number: 38-01087 to 38-07259
*A
118014
09/13/02
RGL
Changed the KT266 word to K7 Series in the title and features in page 1.
Filled up all the missing Byte # and Byte heading description on all the serial
configuration tables on pages 6-12.
Replaced the package drawing and dimension as per CY standard.
Removed the word “PRELIMINARY”
*B
122860
12/19/02
RBI
Added power-up requirements to maximum ratings information.
*C
358435
See ECN
RGL
Added Lead-free devices
Document #: 38-07259 Rev. *C
Page 20 of 20
Similar pages