MPD D109ERW Low cost, miniature 1w sip, wide input dc/dc converter Datasheet

D100ERW Series
Low Cost, Miniature
1W SIP, Wide Input
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 1W Output Power
• 2:1 Input Voltage Range
• 1,500 VDC Isolation
• Short Circuit Protected
• Miniature SIP Case
• Single & Dual Outputs
• 1.0 MH MTBF
• Industry Standard Pin-Out
• Low Low Cost!!
RoHS Compliant
Input
Parameter
Input Voltage Range
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
Min.
4.5
9.0
18.0
36.0
Typ.
5.0
12.0
24.0
48.0
Reverse Polarity Input Current
Short Circuit Input Power
Max.
9.0
18.0
36.0
72.0
1.0
1,500
Units
Max.
±3.0
±2.0
±0.5
±0.75
±1.0
100
Units
%
%
%
%
%
mV P - P
%
%/°C
VDC
A
mW
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation , Single Output
Load Regulation , Dual Output
Ripple & Noise (20 MHz) (Note 1)
Output Power Protection
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Vin = Min to Max
Iout = 10% to 100%
Iout = 10% to 100%
Typ.
±1.0
±1.0
±0.2
±0.5
±0.5
25
120
±0.03
Continuous with Autorecovery
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
500 VDC
100 kHz, 1V
Iout = 100%
Min.
1,500
1,000
Typ.
Max.
550
Units
VDC
MΩ
pF
kHz
Max.
+85
+125
Units
°C
°C
95
%
80
180
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Min.
Typ.
-40
+25
-55
Free Air Convection
RH, Non-condensing
Ambient
MicroPower Direct Physical
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Size
Case Material
Weight
0.87 x 0.47 x 0.37 Inches (22.0 x 12.0 x 9.50 mm)
Non-Conductive Black Plastic (UL94-V0)
0.19 Oz (5.5g)
Reliability Specifications
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
1.0
Typ.
Max.
Units
MHours
Conditions
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
11.0
22.0
40.0
80.0
300
1,800
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
All Models
VDC
°C
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D101ERW
D102ERW
D103ERW
D104ERW
D105ERW
D106ERW
D107ERW
D108ERW
D109ERW
D111ERW
D112ERW
D113ERW
D114ERW
D115ERW
D116ERW
D117ERW
D118ERW
D119ERW
D121ERW
D122ERW
D123ERW
D124ERW
D125ERW
D126ERW
D127ERW
D128ERW
D129ERW
D131ERW
D132ERW
D133ERW
D134ERW
D135ERW
D136ERW
D137ERW
D138ERW
D139ERW
Input
Output
Efficiency
Voltage Current
Current
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Typ)
5
4.5 - 9.0
303
40
3.3
303.0
30.0
66
5
4.5 - 9.0
286
40
5.0
200.0
20.0
70
5
4.5 - 9.0
273
40
12.0
83.0
8.0
73
5
4.5 - 9.0
277
40
15.0
67.0
12.0
72
5
4.5 - 9.0
286
40
24.0
42.0
4.0
70
5
4.5 - 9.0
282
40
±5.0
±100.0
±10.0
71
5
4.5 - 9.0
273
40
±12.0
±42.0
±4.0
73
5
4.5 - 9.0
273
40
±15.0
±33.0
±3.0
73
5
4.5 - 9.0
282
40
±24.0
±21.0
±2.0
71
12
9.0 - 18.0
122
20
3.3
303.0
30.0
68
12
9.0 - 18.0
111
20
5.0
200.0
20.0
75
12
9.0 - 18.0
106
20
12.0
83.0
8.0
78
12
9.0 - 18.0
106
20
15.0
67.0
12.0
78
12
9.0 - 18.0
108
20
24.0
42.0
4.0
77
12
9.0 - 18.0
111
20
±5.0
±100.0
±10.0
75
12
9.0 - 18.0
108
20
±12.0
±42.0
±4.0
77
12
9.0 - 18.0
110
20
±15.0
±33.0
±3.0
76
12
9.0 - 18.0
108
20
±24.0
±21.0
±2.0
77
24
18.0 - 36.0
60
10
3.3
303.0
30.0
70
24
18.0 - 36.0
57
10
5.0
200.0
20.0
73
24
18.0 - 36.0
53
10
12.0
83.0
8.0
78
24
18.0 - 36.0
55
10
15.0
67.0
12.0
76
24
18.0 - 36.0
54
10
24.0
42.0
4.0
77
24
18.0 - 36.0
55
10
±5.0
±100.0
±10.0
76
24
18.0 - 36.0
54
10
±12.0
±42.0
±4.0
78
24
18.0 - 36.0
53
10
±15.0
±33.0
±3.0
78
24
18.0 - 36.0
53
10
±24.0
±21.0
±2.0
78
48
36.0 - 72.0
29
5
3.3
303.0
30.0
71
48
36.0 - 72.0
29
5
5.0
200.0
20.0
73
48
36.0 - 72.0
27
5
12.0
83.0
8.0
78
48
36.0 - 72.0
27
5
15.0
67.0
12.0
76
48
36.0 - 72.0
27
5
24.0
42.0
4.0
78
48
36.0 - 72.0
28
5
±5.0
±100.0
±10.0
75
48
36.0 - 72.0
27
5
±12.0
±42.0
±4.0
78
48
36.0 - 72.0
27
5
±15.0
±33.0
±3.0
78
48
36.0 - 72.0
27
5
±24.0
±21.0
±2.0
76
Notes:
1. When measuring output ripple, it is recommended that an external ceramic
capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout
pin for single output units and from each output to common for dual output
units.
2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit.
3. These converters are specified for operation without external components.
However, in some
Output Capacitor
applications the
Input
Vin Capacitor
Vout 0 - 70ºC -40 - 85ºC
addition of input/
output capacitors
(Electrolitic) (Tantalum)
will enhance stabil100 µF
5 VDC
100 µF
47 µF
ity and reduce out- 12 VDC
100 µF
12 VDC
100 µF
47 µF
put ripple. Recom- 15 VDC
mended capacitor 24 VDC
10 µF
15 VDC
100 µF
47 µF
values are given in 48 VDC
10 µF
the table at right.
Output ripple on single output units may be further enhanced by using the CS
terminal (single output units operated at 50% load or below should use this
function). A low ESR capaciOutput Voltage
tor is connected between
the CS pin and the -Vout pin
3.3V
5V
12V
15V
24V
(the anode of the capacitor
CS
47 µF - 100 µF
22 µF - 47 µF
is connected to the -Vout
pin). Recommended capacitor values are given in the table above. If not used,
the CS pin should be left open.
4. Dual output units may be connected to provide a 10V, 24V, 30V or 48 VDC
output. To do this, connect the load across the +Vout and -Vout outputs
and float the output common.
5. The remote on/off control pin is referMin
Max
enced to the -Vin pin. Input current to
On
<0.6 VDC to Open Circuit
the pin should be between 5 - 10 mA
Off
2.7 VDC
15.0 VDC
with a maximum of 20 mA.
6. It is recommended that a fuse be used
on the input of a power supply for protection. See the Model Selection table
above for the correct rating.
Fuse Rating
Slow-Blow
(mA)
750
750
750
750
750
750
750
750
750
400
400
400
400
400
400
400
400
400
150
150
150
150
150
150
150
150
150
75
75
75
75
75
75
75
75
75
Derating Curve
Pin Connections
Pin Single
Dual
1
-Vin
-Vin
2
+Vin
+Vin
3
Remote ON/OFF
5
NF
NF
6 +Vout
+Vout
7
-Vout Common
8
CS
-Vout
NF = No Function
Mechanical Dimensions
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages