ETC1 D111EI Low cost, 1w high isolation sip dc/dc converter Datasheet

D100EI Series
Low Cost, 1W
High Isolation SIP
DC/DC Converters
New Budget Saver!!
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
● 1W Output Power
● 3,000 VDC Isolation
● Miniature SIP Case
● Single & Dual Outputs
● >1 MHour MTBF
● 24 Standard Models
● LOWEST COST!!
Parameter
Input Voltage Range
Conditions
Min.
Typ.
Max.
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
Input Filter
Units
VDC
Internal Capacitor
Reverse Polarity Input Current
0.3
A
Typ.
Max.
Units
±1.0
±3.0
%
Dual Output , Balanced Loads
±0.1
±1.0
%
For Vin Change of 1%
±1.2
Output
Parameter
Conditions
Min.
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation (Note 1)
%
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
Output Power Protection
50
75
mV P - P
±0.02
±0.03
%/ºC
Max.
Units
120
Temperature Coefficient
Output Short Circuit
%
Momentary (1.0 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Min.
60 Seconds
3,000
500 VDC
1,000
100 kHz, 1V
Switching Frequency
Typ.
VDC
MΩ
60
pF
100
150
200
kHz
Environmental
Parameter
Min.
Typ.
Max.
Units
Operating Temperature Range
Conditions
Ambient
-40
+25
+85
ºC
Operating Temperature Range
Case
-40
+90
ºC
-55
+125
ºC
95
%
Storage Temperature Range
Cooling
Humidity
MicroPower Direct
Physical
232 Tosca Drive
Stoughton, MA 02072
USA
Case Size
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Free Air Convection
RH, Non-condensing
0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.07 Oz (2.1g)
Reliability Specifications
Parameter
MTBF
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
Typ.
Max.
1.0
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
Min.
Typ.
Max.
5 VDC Input
-0.7
9.0
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
Units
VDC
1.5 mm From Case For 10 Sec
300
ºC
All Models
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D101EI
D102EI
D103EI
D104EI
D105EI
D106EI
D107EI
D108EI
D111EI
D112EI
D113EI
D114EI
D115EI
D116EI
D117EI
D118EI
D121EI
D122EI
D123EI
D124EI
D125EI
D126EI
D127EI
D128EI
Notes:
Input
Output
Load
Fuse Rating
Efficiency
Voltage (VDC)
Current (mA)
Slow-Blow
Voltage Current
Current Regulation
(%, Typ)
(%, Max)
(mA)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min)
5
4.5 - 5.5
256
30
5.0
200.0
20.0
15
78
500
5
4.5 - 5.5
256
30
9.0
111.0
12.0
15
78
500
5
4.5 - 5.5
250
30
12.0
83.0
9.0
15
80
500
5
4.5 - 5.5
247
30
15.0
67.0
7.0
15
81
500
5
4.5 - 5.5
278
30
±5.0
±100.0
±10.0
15
72
500
5
4.5 - 5.5
267
30
±9.0
±56.0
±6.0
15
78
500
5
4.5 - 5.5
247
30
±12.0
±42.0
±5.0
15
81
500
5
4.5 - 5.5
250
30
±15.0
±33.0
±4.0
15
80
500
12
10.8 - 13.2
107
15
5.0
200.0
20.0
15
78
200
12
10.8 - 13.2
104
15
9.0
111.0
12.0
15
80
200
12
10.8 - 13.2
103
15
12.0
83.0
9.0
15
81
200
12
10.8 - 13.2
104
15
15.0
67.0
7.0
15
80
200
12
10.8 - 13.2
114
15
±5.0
±100.0
±10.0
15
75
200
12
10.8 - 13.2
104
15
±9.0
±56.0
±6.0
15
80
200
12
10.8 - 13.2
103
15
±12.0
±42.0
±5.0
15
81
200
12
10.8 - 13.2
105
15
±15.0
±33.0
±4.0
15
79
200
24
21.6 - 26.4
53
8
5.0
200.0
20.0
15
78
100
24
21.6 - 26.4
53
8
9.0
111.0
12.0
15
79
100
24
21.6 - 26.4
53
8
12.0
83.0
9.0
15
79
100
24
21.6 - 26.4
53
8
15.0
67.0
7.0
15
79
100
24
21.6 - 26.4
58
8
±5.0
±100.0
±10.0
15
72
100
24
21.6 - 26.4
55
8
±9.0
±56.0
±6.0
15
78
100
24
21.6 - 26.4
53
8
±12.0
±42.0
±5.0
15
78
100
24
21.6 - 26.4
52
8
±15.0
±33.0
±4.0
15
80
100
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters
will operate without
Output Capacitor
Input
Vin
Vout
external compoCapacitor
Single
Dual
nents. However,
5 VDC
4.7 μF
5 VDC 10.0 μF
4.7 μF
when measuring
12 VDC
2.2 μF
9 VDC 4.7 μF
2.2 μF
output ripple, it is
recommended that
24 VDC
1.0 μF 12 VDC 2.2 μF
1.0 μF
an external ceramic
15 VDC 1.0 μF 0.47 μF
capacitor be placed
from the +Vout pin to the -Vout pin for single output units and from each
output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor
values are given in the table above. For applications requiring very low
output noise levels, a simple LC filter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC
output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
Single
Dual
Pin
Single
Dual
1
2
5
+Vin
-Vin
-Vout
+Vin
-Vin
-Vout
6
7
No Pin
+Vout
Common
+Vout
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the
side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: [email protected]
Similar pages