MPD D207RW Miniature sip, 2w wide input range dc/dc converter Datasheet

D200RW Series
Miniature SIP, 2W
Wide Input Range
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• 2:1 Input Voltage Range
Input
Parameter
Input Voltage Range
• 1,000 VDC Isolation
• Short Circuit Protected
• Miniature SIP Case
• Single & Dual Outputs
Input Filter
Input Reflected Ripple Current
Reverse Polarity Input Current
Short Circuit Input Power
• 2.7 MH MTBF
Output
• Industry Standard Pin-Out
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
Conditions
Min.
5 VDC Input
4.5
12 VDC Input
9.0
24 VDC Input 18.0
48 VDC Input 36.0
Capacitor Filter
Typ.
5.0
12.0
24.0
48.0
Max.
9.0
18.0
36.0
72.0
35
1.0
1,500
Conditions
Min.
Typ.
±2.0
Max.
±2.0
±0.5
±1.0
80
Vin = Min to Max
Iout = 25% to 100%
120
±0.02
Units
VDC
mA P - P
A
mW
Units
%
%
%
%
mV P - P
%
%/°C
Continuous (Autorecovery)
General
RoHS Compliant
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
1,000 VDC
100 kHz, 1V
Min.
1,000
1,000
Typ.
Max.
650
Units
VDC
MΩ
pF
kHz
Max.
+85
+100
+125
Units
°C
°C
°C
95
%
60
100
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Ambient
Case
Min.
-40
Typ.
+25
-40
Free Air Convection
RH, Non-condensing
Physical
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Case Size
Case Material
Weight
0.86 x 0.36 x 0.44 Inches (21.89 x 9.2 x 11.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.17 Oz (4.8g)
Remote On/Off
Parameter
Unit On (Note 2)
Unit Off (Note 2)
Off Idle Current
Conditions
Min.
0
Typ.
Max.
0.8
5.0
Units
VDC
VDC
mA
5.0
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
2.73
Typ.
Max.
Units
MHours
Conditions
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
12.0
24.0
40.0
80.0
260
1,800
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
All Models
VDC
°C
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D201RW
D202RW
D203RW
D204RW
D205RW
D206RW
D207RW
D208RW
D211RW
D212RW
D213RW
D214RW
D215RW
D216RW
D217RW
D218RW
D221RW
D222RW
D223RW
D224RW
D225RW
D226RW
D227RW
D228RW
D231RW
D232RW
D233RW
D234RW
D235RW
D236RW
D237RW
D238RW
Input
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
5
4.5 - 9.0
492
15
5
4.5 - 9.0
571
15
5
4.5 - 9.0
555
30
5
4.5 - 9.0
547
30
5
4.5 - 9.0
571
20
5
4.5 - 9.0
533
25
5
4.5 - 9.0
533
25
5
4.5 - 9.0
563
60
12
9.0 - 18.0
205
15
12
9.0 - 18.0
216
15
12
9.0 - 18.0
208
15
12
9.0 - 18.0
213
15
12
9.0 - 18.0
222
15
12
9.0 - 18.0
208
15
12
9.0 - 18.0
210
15
12
9.0 - 18.0
219
30
24
18.0 - 36.0
98
8
24
18.0 - 36.0
108
8
24
18.0 - 36.0
104
8
24
18.0 - 36.0
104
8
24
18.0 - 36.0
106
8
24
18.0 - 36.0
104
8
24
18.0 - 36.0
104
8
24
18.0 - 36.0
106
20
48
36.0 - 72.0
48
6
48
36.0 - 72.0
56
6
48
36.0 - 72.0
53
6
48
36.0 - 72.0
53
6
48
36.0 - 72.0
56
6
48
36.0 - 72.0
53
6
48
36.0 - 72.0
52
6
48
36.0 - 72.0
55
12
Output
Capacitive
Efficiency
Load
Voltage
Current
Current
(%, Typ)
(µF, Max)
(VDC) (mA, Max) (mA, Min)
3.3
500.0
125.0
67
3,300
5.0
400.0
100.0
70
3,300
12.0
167.0
42.0
72
470
15.0
133.0
33.0
73
470
±5.0
±200.0
±50.0
70
±1,000
±12.0
±83.0
±21.0
75
±220
±15.0
±67.0
±17.0
75
±220
±24.0
±42.0
±10.0
71
±100
3.3
500.0
125.0
67
3,300
5.0
400.0
100.0
77
3,300
12.0
167.0
42.0
80
470
15.0
133.0
33.0
78
470
±5.0
±200.0
±50.0
75
±1,000
±12.0
±83.0
±21.0
80
±220
±15.0
±67.0
±17.0
79
±220
±24.0
±42.0
±10.0
76
±100
3.3
500.0
125.0
70
3,300
5.0
400.0
100.0
77
3,300
12.0
167.0
42.0
80
470
15.0
133.0
33.0
80
470
±5.0
±200.0
±50.0
78
±1,000
±12.0
±83.0
±21.0
80
±220
±15.0
±67.0
±17.0
80
±220
±24.0
±42.0
±10.0
78
±100
3.3
500.0
125.0
71
3,300
5.0
400.0
100.0
74
3,300
12.0
167.0
42.0
78
470
15.0
133.0
33.0
78
470
±5.0
±200.0
±50.0
74
±1,000
±12.0
±83.0
±21.0
79
±220
±15.0
±67.0
±17.0
80
±220
±24.0
±42.0
±10.0
75
±100
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
700
700
700
350
350
350
350
350
350
350
350
135
135
135
135
135
135
135
135
Mechanical Dimensions
Other input/output combinations are available
(i.e. 9.0 VDC). Contact the factory for details at:
[email protected]
Notes:
1. An external capacitor should be placed from the +Vout pin to the -Vout pin for
single output units and from each output to common for dual output units. For
single output units a 100 µF is recommended, for dual output models ±48 µF
should be used.
2. The Remote On/Off Control input (Pin 3) is referenced to -Vin (Pin 1). Connection
to the pin should be made through a 1kΩ resistor and diode (1N4148). If it is
not used, the control pin should be left open or tied directly to -Vin (Pin 1).
3. Operation at no-load will not damage these units. However, they may not
meet all specifications.
4. Dual output units may be connected to provide a 10 VDC, 24 VDC, 30 VDC or
48 VDC output. To do this, connect the load across the positive (+Vout) and
negative (-Vout) outputs and float the output common.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Derating Curve
A metal case is available
Contact the factory for details at:
[email protected]
Pin Connections
Pin
1
2
3
5
6
7
8
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
Single
Dual
-Vin
-Vin
+Vin
+Vin
Remote ON/OFF
NC
NC
+Vout
+Vout
-Vout
Common
NC
-Vout
NC = No Connection
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages