MPD D211ED Very low cost, 2w sip dual isolated output dc/dc converter Datasheet

D200ED Series
Very Low Cost, 2W SIP
Dual Isolated Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
Parameter
Conditions
Min.
Typ.
Max.
5 VDC Input
4.5
5.0
5.5
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
• 2W Output Power
• Miniature SIP Case
Input Voltage Range
• UL Approved (File E245422)
• Dual Isolated Outputs
• 1,000 VDC Isolation
Input Filter
Units
VDC
Internal Capacitor
Reverse Polarity Input Current
0.3
A
Max.
Units
Output
• >3.5 MHour MTBF
Parameter
• 12 Standard Models
Output Voltage Accuracy
• Industry Standard Pin-Out
Line Regulation
• LOWEST COST!!
Conditions
Min.
Typ.
±3.0
%
For Vin Change of 1%
±1.2
%
Load Regulation
Iout = 10% to 100%
±15.0
Ripple (20 MHz)
See Note 2
Noise (20 MHz)
See Note 2
Output Power Protection
75
150
mV P - P
150
250
mV P - P
±0.01
±0.02
%/ºC
Max.
Units
120
Temperature Coefficient
Output Short Circuit
%
Momentary (0.5 Sec.)
General
RoHS Compliant
Parameter
Conditions
Isolation Voltage, Input/Output
Min.
1,000
VDC
1,000
VDC
500 VDC
1,000
Isolation Voltage, Output/Output
Isolation Resistance
Isolation Capacitance
Typ.
60 Seconds
100 kHz, 1V
Switching Frequency
MΩ
60
pF
70
kHz
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
Humidity
Suite D
Stoughton, MA 02072
USA
Case Size
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Reliability Specifications
Typ.
Max.
Units
-40
+25
+85
ºC
+125
ºC
95
%
-55
Cooling
MicroPower Direct Physical
292 Page Street
Min.
Free Air Convection
RH, Non-condensing
0.77 x 0.28 x 0.39 Inches (19.6 x 7.0 x 10.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
Parameter
MTBF
0.09 Oz (2.8g)
Conditions
Min.
MIL HDBK 217F, 25ºC, Gnd Benign
Typ.
Max.
3.5
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
Min.
Typ.
Max.
5 VDC Input
-0.7
9.0
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
Units
VDC
1.5 mm From Case For 10 Sec
300
ºC
All Models
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Model
Number
Voltage (VDC)
Output 1
Current (mA)
Output 2
Voltage
Current
Current
Voltage
Current
Current
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
Nominal
Range
Full-Load
No-Load
(VDC)
(mA, Max)
(mA, Min)
(VDC)
(mA, Max)
(mA, Min)
D201ED
5
4.5 - 5.5
500
30
5.0
200.0
20.0
5.0
200.0
20.0
80
1,000
D202ED
5
4.5 - 5.5
487
30
9.0
112.0
12.0
9.0
112.0
12.0
82
1,000
D203ED
5
4.5 - 5.5
487
30
12.0
83.0
9.0
12.0
83.0
9.0
82
1,000
D204ED
5
4.5 - 5.5
481
30
15.0
67.0
7.0
15.0
67.0
7.0
83
1,000
D211ED
12
10.8 - 13.2
208
12
5.0
200.0
20.0
5.0
200.0
20.0
80
500
D212ED
12
10.8 - 13.2
201
12
9.0
112.0
12.0
9.0
112.0
12.0
83
500
D213ED
12
10.8 - 13.2
196
12
12.0
83.0
9.0
12.0
83.0
9.0
85
500
D214ED
12
10.8 - 13.2
201
12
15.0
67.0
7.0
15.0
67.0
7.0
83
500
D221ED
24
21.6 - 26.4
102
7
5.0
200.0
20.0
5.0
200.0
20.0
81
250
D222ED
24
21.6 - 26.4
101
7
9.0
112.0
12.0
9.0
112.0
12.0
82
250
D223ED
24
21.6 - 26.4
99
7
12.0
83.0
9.0
12.0
83.0
9.0
84
250
D224ED
24
21.6 - 26.4
99
7
15.0
67.0
7.0
15.0
67.0
7.0
84
250
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic
capacitor (approx approx 1 µF to 10 µF) be placed from each output to
common.
3. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
4. These converters are specified for operation without external components.
However, in some applications the addition of input/ouput capacitors will
enhance stability and reduce output ripple. Recommended capacitor values
are:
Vin
5 VDC
12 VDC
24 VDC
Input
Capacitor
4.7 µF
2.2 µF
1.0 µF
Vout
5 VDC
9 VDC
12 VDC
15 VDC
Block Diagram
Output
Capacitor
4.7 µF
2.2 µF
1.0 µF
0.47 µF
For applications requiring very low output noise levels, a simple LC filter
should be effective.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating
g Curve
Mechanical Dimensions
Pin Connections
Pin
Function
1
2
4
5
6
7
+Vin
-Vin
-Vout 1
+Vout 1
-Vout 2
+Vout 2
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages