MPD D216I High isolation miniature, 2w sip dc/dc converter Datasheet

D200I Series
High Isolation
Miniature, 2W SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
Input
Parameter
• Miniature SIP Case
• Single & Dual Outputs
Input Voltage Range
• 3,000 VDC Isolation
• >1.12 MHour MTBF
• 28 Standard Models
• Industry Standard Pin-Out
RoHS Compliant
Input Filter
Reflected Ripple Current
Conditions
Min.
5 VDC Input
4.5
12 VDC Input 10.8
24 VDC Input 21.6
48 VDC Input 43.2
Internal Capacitor
12 μH Source Inductance
Typ.
Max.
Units
5.0
12.0
24.0
48.0
5.5
13.2
26.4
52.8
VDC
20
mA P - P
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
Conditions
Min.
Typ.
Max.
±3.0
Dual Output , Balanced Loads
±1.0
For Vin Change of 1%
±1.2
See Model Selection Guide
75
120
Units
%
%
%
±0.02
mV P - P
%
%/ºC
Max.
Units
Momentary (0.5 Sec.)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Min.
60 Seconds
500 VDC
100 kHz, 1V
Typ.
3,000
1,000
VDC
MΩ
pF
kHz
60
80
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Conditions
Ambient
Case
Min.
Typ.
Max.
Units
-40
+25
+85
+100
+125
ºC
ºC
ºC
95
%
-40
Free Air Convection
RH, Non-condensing
Physical
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
Weight
0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)
0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.08 Oz (2.3g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
Typ.
Max.
1.12
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
All Models
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
7.0
15.0
28.0
54.0
260
650
Units
VDC
ºC
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D201I
D202I
D203I
D204I
D205I
D206I
D207I
D211I
D212I
D213I
D214I
D215I
D216I
D217I
D221I
D222I
D223I
D224I
D225I
D226I
D227I
D231I
D232I
D233I
D234I
D235I
D236I
D237I
Input
Output
Load
Voltage (VDC)
Current (mA)
Regulation
Voltage Current
Current
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max)
5
4.5 - 5.5
367
30
3.3
400.0
10.0
20
5
4.5 - 5.5
512
30
5.0
400.0
8.0
10
5
4.5 - 5.5
500
30
12.0
165.0
3.5
10
5
4.5 - 5.5
500
30
15.0
133.0
2.7
10
5
4.5 - 5.5
555
30
±5.0
±200.0
±4.0
10
5
4.5 - 5.5
512
30
±12.0
±83.3
±1.7
10
5
4.5 - 5.5
500
30
±15.0
±66.6
±1.4
10
12
10.8 - 13.2
169
20
3.3
400.0
10.0
20
12
10.8 - 13.2
216
20
5.0
400.0
8.0
10
12
10.8 - 13.2
203
20
12.0
165.0
3.5
10
12
10.8 - 13.2
203
20
15.0
133.0
2.7
10
12
10.8 - 13.2
222
20
±5.0
±200.0
±4.0
10
12
10.8 - 13.2
203
20
±12.0
±83.3
±1.7
10
12
10.8 - 13.2
203
20
±15.0
±66.6
±1.4
10
24
21.6 - 26.4
76
10
3.3
400.0
10.0
20
24
21.6 - 26.4
105
10
5.0
400.0
8.0
10
24
21.6 - 26.4
102
10
12.0
165.0
3.5
10
24
21.6 - 26.4
101
10
15.0
133.0
2.7
10
24
21.6 - 26.4
111
10
±5.0
±200.0
±4.0
10
24
21.6 - 26.4
101
10
±12.0
±83.3
±1.7
10
24
21.6 - 26.4
101
10
±15.0
±66.6
±1.4
10
48
43.2 - 52.8
45
6
3.3
400.0
10.0
20
48
43.2 - 52.8
54
6
5.0
400.0
8.0
10
48
43.2 - 52.8
53
6
12.0
165.0
3.5
10
48
43.2 - 52.8
53
6
15.0
133.0
2.7
10
48
43.2 - 52.8
57
6
±5.0
±200.0
±4.0
10
48
43.2 - 52.8
52
6
±12.0
±83.3
±1.7
10
48
43.2 - 52.8
52
6
±15.0
±66.6
±1.4
10
72
78
82
82
72
78
80
65
77
82
82
75
82
82
72
79
80
82
75
82
82
60
77
78
78
73
80
80
Pin Connections
Capacitive Load
Other input/output combinations are available
(i.e. 24.0 VDC). Contact the factory for details at:
[email protected]
Single Output
(μF Max)
Dual Output
(μF Max)
470
±220
Notes:
1. Output load regulation is specified for a load change of 20% to 100%.
2. These units do not require external components to operate, but the use of an input capacitor (10 μF) may enhance performance in some applications. It is recommended that an
input capacitor of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input
model.
An output capacitor (4.7 μF to 220 μF or ±4.7 μF to ±100 μF) may be used to reduce ripple.
To improve EMI performance, a simple filter network consisting of a 10 uF to 100 uF capacitor and 12 uH inductor should be effective.
3. These units will operate at no load without damage, but may not meet all specifications.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this,
connect the load across the positive (+Vout) and negative (-Vout) outputs and float the
output common.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
200
200
200
200
200
200
200
100
100
100
100
100
100
100
Efficiency
(%, Typ)
Pin
Single
Dual
1
2
5
6
7
+Vin
-Vin
-Vout
No Pin
+Vout
+Vin
-Vin
-Vout
Common
+Vout
Mechanical Dimensions
Derating Curve
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
Notes:
• All dimensio
dimensions are typical in inches (mm)
• Tolerance xx.xx = ±0.01 (±0.25)
marked by a “dot” or indentation
• Pin 1 is mar
on the side of the unit
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages