TI DAC902E/2K5

DAC902
902
DAC
DAC
902
SBAS094B – MAY 2002
12-Bit, 165MSPS
DIGITAL-TO-ANALOG CONVERTER
TM
FEATURES
APPLICATIONS
● SINGLE +5V OR +3V OPERATION
● COMMUNICATION TRANSMIT CHANNELS:
WLL, Cellular Base Station
Digital Microwave Links
Cable Modems
● HIGH SFDR: 5MHz Output at 100MSPS: 67dBc
● LOW GLITCH: 3pV-s
● LOW POWER: 170mW at +5V
● WAVEFORM GENERATION:
Direct Digital Synthesis (DDS)
Arbitrary Waveform Generation (ARB)
● INTERNAL REFERENCE:
Optional Ext. Reference
Adjustable Full-Scale Range
Multiplying Option
● MEDICAL/ULTRASOUND
● HIGH-SPEED INSTRUMENTATION AND CONTROL
● VIDEO, DIGITAL TV
DESCRIPTION
For noncontinuous operation of the DAC902, a power-down mode
results in only 45mW of standby power.
The DAC902 is a high-speed, Digital-to-Analog Converter (DAC)
offering a 12-bit resolution option within the SpeedPlus Family of
high-performance converters. Featuring pin compatibility among
family members, the DAC908, DAC900, and DAC904 provide a
component selection option to an 8-, 10-, and 14-bit resolution,
respectively. All models within this family of DACs support update
rates in excess of 165MSPS with excellent dynamic performance,
and are especially suited to fulfill the demands of a variety of
applications.
The DAC902 comes with an integrated 1.24V bandgap reference
and edge-triggered input latches, offering a complete converter
solution. Both +3V and +5V CMOS logic families can be interfaced to the DAC902.
The advanced segmentation architecture of the DAC902 is optimized to provide a high Spurious-Free Dynamic Range (SFDR) for
single-tone, as well as for multi-tone signals—essential when used
for the transmit signal path of communication systems.
The DAC902 has a high impedance (200kΩ) current output with a
nominal range of 20mA and an output compliance of up to 1.25V.
The differential outputs allow for both a differential or singleended analog signal interface. The close matching of the current
outputs ensures superior dynamic performance in the differential
configuration, which can be implemented with a transformer.
Utilizing a small geometry CMOS process, the monolithic DAC902
can be operated on a wide, single-supply range of +2.7V to +5.5V.
Its low power consumption allows for use in portable and batteryoperated systems. Further optimization can be realized by lowering
the output current with the adjustable full-scale option.
The reference structure of the DAC902 allows for additional
flexibility by utilizing the on-chip reference, or applying an external reference. The full-scale output current can be adjusted over a
span of 2mA to 20mA, with one external resistor, while maintaining the specified dynamic performance.
The DAC902 is available in the SO-28 and TSSOP-28 packages.
+VA
+VD
BW
DAC902
FSA
Current
Sources
REFIN
IOUT
LSB
Switches
IOUT
BYP
Segmented
Switches
INT/EXT
Latches
PD
+1.24V Ref.
12-Bit Data Input
AGND
CLK
D11...D0
DGND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright © 2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS
ELECTROSTATIC
DISCHARGE SENSITIVITY
+VA to AGND ........................................................................ –0.3V to +6V
+VD to DGND ........................................................................ –0.3V to +6V
AGND to DGND ................................................................. –0.3V to +0.3V
+VA to +VD ............................................................................... –6V to +6V
CLK, PD to DGND ..................................................... –0.3V to VD + 0.3V
D0-D11 to DGND ....................................................... –0.3V to VD + 0.3V
IOUT, IOUT to AGND ........................................................ –1V to VA + 0.3V
BW, BYP to AGND ..................................................... –0.3V to VA + 0.3V
REFIN, FSA to AGND ................................................. –0.3V to VA + 0.3V
INT/EXT to AGND ...................................................... –0.3V to VA + 0.3V
Junction Temperature .................................................................... +150°C
Case Temperature ......................................................................... +100°C
Storage Temperature .................................................................... +125°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER
DAC902U
SO-28
217
–40°C to +85°C
DAC902U
DAC902U
Rails
"
"
"
"
DAC902U/1K
Tape and Reel
TSSOP-28
360
–40°C to +85°C
DAC902E
DAC902E
Rails
"
"
"
"
DAC902E/2K5
Tape and Reel
"
DAC902E
"
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces
of “DAC902E/2K5” will get a single 2500-piece Tape and Reel.
DEMO BOARD ORDERING INFORMATION
PRODUCT
DEMO BOARD
ORDERING NUMBER
DAC902U
DAC902E
DEM-DAC90xU
DEM-DAC902E
COMMENT
Populated evaluation board without the DAC. Order sample of desired DAC90x model separately.
Populated evaluation board including the DAC902E.
ELECTRICAL CHARACTERISTICS
At TA = full specified temperature range, +VA = +5V, +VD = +5V, differential transformer coupled output, 50Ω doubly terminated, unless otherwise specified.
DAC902U/E
PARAMETER
CONDITIONS
MIN
MAX
UNITS
12
Bits
125
165
–40
165
200
+85
MSPS
MSPS
°C
–1.75
–2.5
±0.5
±1.0
+1.75
+2.5
LSB
LSB
71
77
75
68
67
61
61
57
60
53
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
80
80
dBc
dBc
–74
–75
dBc
dBc
64
dBc
RESOLUTION
OUTPUT UPDATE RATE
Output Update Rate (fCLOCK)
Full Specified Temperature Range, Operating
STATIC ACCURACY(1)
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
DYNAMIC PERFORMANCE
Spurious-Free Dynamic Range (SFDR)
fOUT = 1MHz, fCLOCK = 25MSPS
fOUT = 2.1MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 100MSPS
fOUT = 20.2MHz, fCLOCK = 100MSPS
fOUT = 25.3MHz, fCLOCK = 125MSPS
fOUT = 41.5MHz, fCLOCK = 125MSPS
fOUT = 27.4MHz, fCLOCK = 165MSPS
fOUT = 54.8MHz, fCLOCK = 165MSPS
Spurious-Free Dynamic Range within a Window
fOUT = 5.04MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 100MSPS
Total Harmonic Distortion (THD)
fOUT = 2.1MHz, fCLOCK = 50MSPS
fOUT = 2.1MHz, fCLOCK = 125MSPS
Two Tone
fOUT1 = 13.5MHz, fOUT2 = 14.5MHz, fCLOCK = 100MSPS
2
2.7V to 3.3V
4.5V to 5.5V
Ambient, TA
fCLOCK
TA = +25°C
= 25MSPS, fOUT = 1.0MHz
TYP
TA = +25°C
To Nyquist
2MHz Span
4MHz Span
DAC902
SBAS094B
ELECTRICAL CHARACTERISTICS (Cont.)
At TA = full specified temperature range, +VA = +5V, +VD = +5V, differential transformer coupled output, 50Ω doubly terminated, unless otherwise specified.
DAC902U/E
PARAMETER
DYNAMIC PERFORMANCE (Cont.)
Output Settling Time(2)
Output Rise Time(2)
Output Fall Time(2)
Glitch Impulse
DC-ACCURACY
Full-Scale Output Range(3)(FSR)
Output Compliance Range
Gain Error
Gain Error
Gain Drift
Offset Error
Offset Drift
Power-Supply Rejection, +VA
Power-Supply Rejection, +VD
Output Noise
Output Resistance
Output Capacitance
CONDITIONS
to 0.1%
10% to 90%
10% to 90%
All Bits High, IOUT
With Internal Reference
With External Reference
With Internal Reference
With Internal Reference
With Internal Reference
POWER SUPPLY
Supply Voltages
+VA
+VD
Supply Current(6)
IVA
IVA, Power-Down Mode
IVD
Power Dissipation
Power Dissipation, Power-Down Mode
Thermal Resistance, θJA
SO-28
TSSOP-28
TYP
MAX
30
2
2
3
2.0
–1.0
–10
–10
±1
±2
±120
–0.025
IOUT = 20mA, RLOAD = 50Ω
20.0
+1.25
+10
+10
+0.025
+0.2
+0.025
50
200
12
IOUT, IOUT to Ground
+1.24
±5
±50
10
1
0.1
1.25
1.3
+VD
+VD
+VD
+VD
+VD
+VD
=
=
=
=
=
=
+5V
+5V
+3V
+3V
+5V
+5V
3.5
2
+2.7
+2.7
+5V, IOUT = 20mA
+3V, IOUT = 2mA
Straight Binary
Rising Edge of Clock
5
0
3
0
±20
±20
5
UNITS
ns
ns
ns
pV-s
±0.1
–0.2
–0.025
REFERENCE
Reference Voltage
Reference Tolerance
Reference Voltage Drift
Reference Output Current
Reference Input Resistance
Reference Input Compliance Range
Reference Small-Signal Bandwidth(4)
DIGITAL INPUTS
Logic Coding
Latch Command
Logic High Voltage, VIH
Logic Low Voltage, VIL
Logic High Voltage, VIH
Logic Low Voltage, VIL
Logic High Current, IIH(5)
Logic Low Current, IIL
Input Capacitance
MIN
mA
V
%FSR
%FSR
ppmFSR/°C
%FSR
ppmFSR/°C
%FSR/V
%FSR/V
pA/√Hz
kΩ
pF
V
%
ppmFSR/°C
µA
MΩ
V
MHz
0.8
V
V
V
V
µA
µA
pF
+5
+5
+5.5
+5.5
V
V
24
1.1
8
170
50
45
30
2
15
230
mA
mA
mA
mW
mW
mW
75
50
1.2
°C/W
°C/W
NOTES: (1) At output IOUT, while driving a virtual ground. (2) Measured single-ended into 50Ω Load. (3) Nominal full-scale output current is 32 • IREF; see Application
Section for details. (4) Reference bandwidth depends on size of external capacitor at the BW pin and signal level. (5) Typically 45µA for the PD pin, which has an
internal pull-down resistor. (6) Measured at fCLOCK = 50MSPS and fOUT = 1.0MHz.
DAC902
SBAS094B
3
PIN CONFIGURATION
PIN DESCRIPTIONS
Top View
SO, TSSOP
Bit 1
1
28
CLK
Bit 2
2
27
+VD
Bit 3
3
26
DGND
Bit 4
4
25
NC
Bit 5
5
24
+VA
Bit 6
6
23
BYP
Bit 7
7
22
IOUT
Bit 8
8
21
IOUT
Bit 9
9
20
AGND
Bit 10 10
19
BW
Bit 11 11
18
FSA
Bit 12 12
17
REFIN
NC 13
16
INT/EXT
NC 14
15
PD
DAC902
PIN
DESIGNATOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
NC
NC
PD
16
INT/EXT
17
REFIN
18
19
FSA
BW
20
21
22
23
24
25
26
27
28
AGND
IOUT
IOUT
BYP
+VA
NC
DGND
+VD
CLK
DESCRIPTION
Data Bit 1 (D11), MSB
Data Bit 2 (D10)
Data Bit 3 (D9)
Data Bit 4 (D8)
Data Bit 5 (D7)
Data Bit 6 (D6)
Data Bit 7 (D5)
Data Bit 8 (D4)
Data Bit 9 (D3)
Data Bit 10 (D2)
Data Bit 11 (D1)
Data Bit 12 (D0), LSB
No Connection
No Connection
Power Down, Control Input; Active
HIGH. Contains internal pull-down circuit;
may be left unconnected if not used.
Reference Select Pin; Internal ( = 0) or
External ( = 1) Reference Operation.
Reference Input/Ouput. See Applications section for further details.
Full-Scale Output Adjust
Bandwidth/Noise Reduction Pin:
Bypass with 0.1µF to +VA for Optimum
Performance.
Analog Ground
Complementary DAC Current Output
DAC Current Output
Bypass Node: Use 0.1µF to AGND
Analog Supply Voltage, 2.7V to 5.5V
No Connection
Digital Ground
Digital Supply Voltage, 2.7V to 5.5V
Clock Input
TYPICAL CONNECTION CIRCUIT
+5V
+5V
0.1µF
+VA
+VD
BW
DAC902
IOUT
LSB
Switches
FSA
Current
Sources
REFIN
RSET
0.1µF
1:1
IOUT
BYP
Segmented
MSB
Switches
0.1µF
50Ω
20pF
50Ω
20pF
INT/EXT
PD
Latches
+1.24V Ref.
12-Bit Data Input
AGND
4
CLK
D11.......D0
DGND
DAC902
SBAS094B
TIMING DIAGRAM
t2
t1
CLOCK
tS
D13 D0
Data Changes
tH
Stable Valid Data
Data Changes
tPD
tSET
Iout or
Iout
SYMBOL
t1
t2
tS
tH
tPD
tSET
DAC902
SBAS094B
DESCRIPTION
Clock Pulse HIGH Time
Clock Pulse LOW Time
Data Setup Time
Data Hold Time
Propagation Delay Time
Output Settling Time to 0.1%
MIN
TYP
3.0
3.0
1.0
1.5
1
30.0
MAX
UNITS
ns
ns
ns
ns
ns
ns
5
TYPICAL CHARACTERISTICS: VD = VA = +5V
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
TYPICAL DNL
2.0
2.0
1.5
1.5
1.0
1.0
0
DAC Code
85
80
80
–6dBFS
75
0dBFS
65
75
–6dBFS
70
65
0dBFS
60
60
55
0
2.0
4.0
6.0
8.0
Frequency (MHz)
10.0
12.0
0
5.0
SFDR vs fOUT AT 100MSPS
10.0
15.0
Frequency (MHz)
20.0
25.0
SFDR vs fOUT AT 125MSPS
85
85
80
80
75
75
SFDR (dBc)
SFDR (dBc)
4000
4096
SFDR vs fOUT AT 50MSPS
85
SFDR (dBc)
SFDR (dBc)
SFDR vs fOUT AT 25MSPS
70
–6dBFS
65
60
55
70
–6dBFS
65
60
55
0dBFS
0dBFS
50
50
45
45
0
6
3500
DAC Code
90
70
3000
0
4000
4096
3500
1000
3000
–2.5
2500
–2.0
–2.5
2000
–1.5
–2.0
1500
–1.0
–1.5
500
–1.0
2500
–0.5
2000
–0.5
0.5
1500
0
1000
0.5
500
Error (LSBs)
2.5
0
Error (LSBs)
TYPICAL INL
2.5
10.0
20.0
30.0
Frequency (MHz)
40.0
50.0
0
10.0
20.0
30.0
40.0
Frequency (MHz)
50.0
60.0
DAC902
SBAS094B
TYPICAL CHARACTERISTICS: VD = VA = +5V (Cont.)
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs fOUT AT 165MSPS
SFDR vs fOUT AT 200MSPS
80
80
75
75
70
70
SFDR (dBc)
SFDR (dBc)
–6dBFS
65
60
55
65
–6dBFS
60
55
0dBFS
0dBFS
50
50
45
45
40
40
0
10.0
20.0
30.0 40.0 50.0
Frequency (MHz)
60.0
70.0
80.0
0
DIFFERENTIAL vs SINGLE-ENDED SFDR vs fOUT
AT 100MSPS
10.0 20.0
30.0 40.0 50.0 60.0 70.0 80.0
Frequency (MHz)
90.0
SFDR vs IOUTFS and fOUT AT 100MSPS, 0dBFS
85
80
2.1MHz
80
X
70
IOUT (–6dBFS)
SFDR (dBc)
75
SFDR (dBc)
75
X
70
Diff (–6dBFS)
65
X
X
X
60
Diff (0dBFS)
20.2MHz
60
10.1MHz
55
40.4MHz
X
X
X
55
50
IOUT (0dBFS)
50
65
X
X
2
5
X
45
45
40
0
10.0
20.0
30.0
Frequency (MHz)
40.0
50.0
10
SFDR vs TEMPERATURE AT 100MSPS, 0dBFS
THD vs fCLOCK AT fOUT = 2.1MHz
85
–70
2HD
80
–75
2.1MHz
–80
SFDR (dBc)
75
THD (dBc)
20
IOUTFS (mA)
3HD
–85
X
X
X
4HD
X
–90
70
10.1MHz
65
60
55
–95
50
–100
0
DAC902
SBAS094B
25
50
100
fCLOCK (MSPS)
125
150
40.4MHz
X
45
–40
X
X
–20
0
X
X
25
50
Temperature (°C)
X
X
70
85
7
TYPICAL CHARACTERISTICS: VD = VA = +5V (Cont.)
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SINGLE-TONE OUTPUT SPECTRUM
DUAL-TONE OUTPUT SPECTRUM
0
0
–10
–10
fCLOCK = 100MSPS
fOUT = 2.1MHz
SFDR = 74dBc
Amplitude = 0dBFS
–30
–40
fCLOCK = 100MSPS
fOUT1 = 13.5MHz
fOUT2 = 14.5MHz
SFDR = 64dBc
Amplitude = 0dBFS
–20
Magnitude (dBm)
Magnitude (dBm)
–20
–50
–60
–70
–80
–30
–40
–50
–60
–70
–80
–90
–90
–100
–100
0
5
10
15
20
25
30
35
40
45
50
0
5
10
Frequency (MHz)
15
20
25
30
35
40
45
50
Frequency (MHz)
FOUR-TONE OUTPUT SPECTRUM
0
–10
fCLOCK = 50MSPS
fOUT1 = 6.25MHz
fOUT2 = 6.75MHz
fOUT3 = 7.25MHz
fOUT4 = 7.75MHz
SFDR = 66dBc
Amplitude = 0dBFS
Magnitude (dBm)
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
5
10
15
20
25
Frequency (MHz)
8
DAC902
SBAS094B
TYPICAL CHARACTERISTICS: VD = VA = +3V
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs fOUT AT 25MSPS
SFDR vs fOUT AT 50MSPS
85
85
80
80
SFDR (dBc)
SFDR (dBc)
–6dBFS
75
70
0dBFS
65
75
–6dBFS
70
65
60
60
55
55
0dBFS
0
2.0
4.0
6.0
8.0
Frequency (MHz)
10.0
12.0
0
5.0
10.0
15.0
Frequency (MHz)
SFDR vs fOUT AT 100MSPS
20.0
25.0
SFDR vs fOUT AT 125MSPS
85
85
80
80
75
75
SFDR (dBc)
SFDR (dBc)
–6dBFS
70
–6dBFS
65
60
70
65
60
0dBFS
55
55
0dBFS
50
50
45
45
0
10.0
20.0
30.0
Frequency (MHz)
40.0
50.0
0
10.0
20.0
30.0
40.0
Frequency (MHz)
50.0
60.0
DIFFERENTIAL vs SINGLE-ENDED SFDR vs fOUT
AT 100MSPS
SFDR vs fOUT AT 165MSPS
80
85
75
80
70
75
Diff (–6dBFS)
–6dBFS
SFDR (dBc)
SFDR (dBc)
IOUT (–6dBFS)
65
60
55
70
Diff (0dBFS)
65
60
55
50
0dBFS
45
50
40
45
0
DAC902
SBAS094B
10.0
20.0
30.0 40.0 50.0
Frequency (MHz)
60.0
70.0
80.0
IOUT (0dBFS)
0
10.0
20.0
30.0
Frequency (MHz)
40.0
50.0
9
TYPICAL CHARACTERISTICS: VD = VA = +3V (Cont.)
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs IOUTFS and fOUT AT 100MSPS, 0dBFS
THD vs fCLOCK AT fOUT = 2.1MHz
–70
80
2.1MHz
2HD
75
–75
–80
10.1MHz
65
60
THD (dBc)
SFDR (dBc)
70
20.2MHz
55
–85
–90
4HD
X
50
X
45
3HD
40.4MHz
X
X
–95
–100
40
2
5
10
0
20
25
50
100
fCLOCK (MSPS)
IOUTFS (mA)
SFDR vs TEMPERATURE AT 100MSPS, 0dBFS
0
–10
80
2.1MHz
Magnitude (dBm)
SFDR (dBc)
70
10.1MHz
65
60
55
40.4MHz
X
45
–40
–30
–40
–50
–60
–70
–80
X
X
X
X
X
X
fCLOCK = 100MSPS
fOUT = 2.1MHz
SFDR = 76dBc
Amplitude = 0dBFS
–20
75
–90
–100
–20
0
25
50
Temperature (°C)
70
85
0
DUAL-TONE OUTPUT SPECTRUM
10
15
20
25
30
35
40
45
50
FOUR-TONE OUTPUT SPECTRUM
0
–10
–10
fCLOCK = 100MSPS
fOUT1 = 13.5MHz
fOUT2 = 14.5MHz
SFDR = 68dBc
Amplitude = 0dBFS
–30
–40
–50
fCLOCK = 50MSPS
fOUT1 = 6.25MHz
fOUT2 = 6.75MHz
fOUT3 = 7.25MHz
fOUT4 = 7.75MHz
SFDR = 66dBc
Amplitude = 0dBFS
–20
Magnitude (dBm)
–20
Magnitude (dBm)
5
Frequency (MHz)
0
–60
–70
–80
–30
–40
–50
–60
–70
–80
–90
–90
–100
–100
0
5
10
15
20
25
30
Frequency (MHz)
10
150
SINGLE-TONE OUTPUT SPECTRUM
85
50
125
35
40
45
50
0
5
10
15
20
25
Frequency (MHz)
DAC902
SBAS094B
APPLICATION INFORMATION
DAC TRANSFER FUNCTION
THEORY OF OPERATION
The total output current, IOUTFS, of the DAC902 is the
summation of the two complementary output currents:
The architecture of the DAC902 uses the current steering
technique to enable fast switching and a high update rate. The
core element within the monolithic DAC is an array of
segmented current sources that are designed to deliver a fullscale output current of up to 20mA, as shown in Figure 1. An
internal decoder addresses the differential current switches
each time the DAC is updated and a corresponding output
current is formed by steering all currents to either output
summing node, IOUT or IOUT. The complementary outputs
deliver a differential output signal that improves the dynamic
performance through reduction of even-order harmonics,
common-mode signals (noise), and double the peak-to-peak
output signal swing by a factor of two, compared to singleended operation.
IOUTFS = IOUT + IOUT
(1)
The individual output currents depend on the DAC code and
can be expressed as:
IOUT = IOUTFS • (Code/4096)
(2)
IOUT = IOUTFS • (4095 – Code/4096)
(3)
where ‘Code’ is the decimal representation of the DAC data
input word. Additionally, IOUTFS is a function of the reference current IREF, which is determined by the reference
voltage and the external setting resistor, RSET.
The segmented architecture results in a significant reduction of the glitch energy, improves the dynamic performance (SFDR), and DNL. The current outputs maintain a
very high output impedance of greater than 200kΩ.
IOUTFS = 32 • IREF = 32 • VREF /RSET
The full-scale output current is determined by the ratio of
the internal reference voltage (1.24V) and an external
resistor, RSET. The resulting IREF is internally multiplied by
a factor of 32 to produce an effective DAC output current
that can range from 2mA to 20mA, depending on the value
of RSET.
(4)
In most cases the complementary outputs will drive resistive
loads or a terminated transformer. A signal voltage will
develop at each output according to:
The DAC902 is split into a digital and an analog portion,
each of which is powered through its own supply pin. The
digital section includes edge-triggered input latches and the
decoder logic, while the analog section comprises the current source array with its associated switches, and the
reference circuitry.
VOUT = IOUT • RLOAD
(5)
VOUT = IOUT • RLOAD
(6)
+3V to +5V
Digital
+3V to +5V
Analog
0.1µF
Bandwidth
Control
+VA
DAC902
RSET
2kΩ
BW
+VD
IOUT
Full-Scale
Adjust
Resistor
FSA
Ref
Control
Amp
Ref
Input REFIN
400pF
PMOS
Current
Source
Array
0.1µF
LSB
Switches
1:1
VOUT
IOUT
Segmented
MSB
Switches
50Ω
0.1µF
20pF
50Ω
20pF
BYP
INT/EXT
Ref
Buffer
Latches and Switch
Decoder Logic
PD
Power Down
(internal pull-down)
+1.24V Ref
AGND
Analog
Ground
12-Bit Data Input
CLK
Clock
Input
DGND
D11...D0
Digital
Ground
NOTE: Supply bypassing not shown.
FIGURE 1. Functional Block Diagram of the DAC902.
DAC902
SBAS094B
11
The value of the load resistance is limited by the output
compliance specification of the DAC902. To maintain specified linearity performance, the voltage for IOUT and IOUT
should not exceed the maximum allowable compliance range.
The two single-ended output voltages can be combined to
find the total differential output swing:
VOUTDIFF = VOUT – VOUT =
(2 • Code – 4095)
• I OUTFS • R LOAD (7)
4096
ANALOG OUTPUTS
The DAC902 provides two complementary current outputs,
IOUT and IOUT. The simplified circuit of the analog output
stage representing the differential topology is shown in
Figure 2. The output impedance of 200kΩ || 12pF for IOUT
and IOUT results from the parallel combination of the differential switches, along with the current sources and associated parasitic capacitances.
IOUT and IOUT. Furthermore, using the differential output
configuration in combination with a transformer will be
instrumental for achieving excellent distortion performance.
Common-mode errors, such as even-order harmonics or
noise, can be substantially reduced. This is particularly the
case with high output frequencies and/or output amplitudes
below full-scale.
For those applications requiring the optimum distortion and
noise performance, it is recommended to select a full-scale
output of 20mA. A lower full-scale range down to 2mA may
be considered for applications that require a low power
consumption, but can tolerate a reduced performance level.
INPUT CODE (D11 - D0)
IOUT
IOUT
1111 1111 1111
20mA
0mA
1000 0000 0000
10mA
10mA
0000 0000 0000
0mA
20mA
TABLE I. Input Coding vs Analog Output Current.
OUTPUT CONFIGURATIONS
+VA
DAC902
IOUT
IOUT
RL
RL
The current output of the DAC902 allows for a variety of
configurations, some of which are illustrated below. As mentioned previously, utilizing the converter’s differential outputs will yield the best dynamic performance. Such a differential output circuit may consist of an RF transformer or a
differential amplifier configuration. The transformer configuration is ideal for most applications with ac coupling, while
op amps will be suitable for a DC-coupled configuration.
The single-ended configuration may be considered for applications requiring a unipolar output voltage. Connecting a
resistor from either one of the outputs to ground will convert
the output current into a ground-referenced voltage signal.
To improve on the DC linearity, an I-to-V converter can be
used instead. This will result in a negative signal excursion
and, therefore, requires a dual supply amplifier.
FIGURE 2. Equivalent Analog Output.
DIFFERENTIAL WITH TRANSFORMER
The signal voltage swing that may develop at the two
outputs, IOUT and IOUT, is limited by a negative and positive
compliance. The negative limit of –1V is given by the
breakdown voltage of the CMOS process, and exceeding it
will compromise the reliability of the DAC902, or even
cause permanent damage. With the full-scale output set to
20mA, the positive compliance equals 1.25V, operating with
+VD = 5V. Note that the compliance range decreases to
about 1V for a selected output current of IOUTFS = 2mA.
Care should be taken that the configuration of DAC902 does
not exceed the compliance range to avoid degradation of the
distortion performance and integral linearity.
Best distortion performance is typically achieved with the
maximum full-scale output signal limited to approximately
0.5V. This is the case for a 50Ω doubly-terminated load and
a 20mA full-scale output current. A variety of loads can be
adapted to the output of the DAC902 by selecting a suitable
transformer while maintaining optimum voltage levels at
12
Using an RF transformer provides a convenient way of
converting the differential output signal into a single-ended
signal while achieving excellent dynamic performance (see
Figure 3). The appropriate transformer should be carefully
selected based on the output frequency spectrum and impedance requirements. The differential transformer configuration has the benefit of significantly reducing common-mode
signals, thus improving the dynamic performance over a
wide range of frequencies. Furthermore, by selecting a
suitable impedance ratio (winding ratio), the transformer can
be used to provide optimum impedance matching while
controlling the compliance voltage for the converter outputs.
The model shown in Figure 3 has a 1:1 ratio and may be used
to interface the DAC902 to a 50Ω load. This results in a 25Ω
load for each of the outputs, IOUT and IOUT. The output
signals are ac coupled and inherently isolated because of its
magnetic coupling.
DAC902
SBAS094B
As shown in Figure 3, the transformer’s center tap is connected to ground. This forces the voltage swing on IOUT and
IOUT to be centered at 0V. In this case the two resistors, RS,
may be replaced with one, RDIFF, or omitted altogether. This
approach should only be used if all components are close to
each other, and if the VSWR is not important. A complete
power transfer from the DAC output to the load can be
realized, but the output compliance range should be observed. Alternatively, if the center tap is not connected, the
signal swing will be centered at RS • IOUTFS/2. However, in
this case, the two resistors (RS) must be used to enable the
necessary DC-current flow for both outputs.
ADT1-1WT
(Mini-Circuits)
1:1
IOUT
DAC902
RS
50Ω
Optional
RDIFF
RL
IOUT
RS
50Ω
The OPA680 is configured for a gain of two. Therefore,
operating the DAC902 with a 20mA full-scale output will
produce a voltage output of ±1V. This requires the amplifier
to operate off of a dual power supply (±5V). The tolerance
of the resistors typically sets the limit for the achievable
common-mode rejection. An improvement can be obtained
by fine tuning resistor R4.
This configuration typically delivers a lower level of ac
performance than the previously discussed transformer solution because the amplifier introduces another source of distortion. Suitable amplifiers should be selected based on their
slew-rate, harmonic distortion, and output swing capabilities.
High-speed amplifiers like the OPA680 or OPA687 may be
considered. The ac performance of this circuit may be improved by adding a small capacitor, CDIFF, between the
outputs IOUT and IOUT (as shown in Figure 4). This will
introduce a real pole to create a low-pass filter in order to
slew-limiting the DACs fast output signal steps that otherwise could drive the amplifier into slew-limitations or into an
overload condition; both would cause excessive distortion.
The difference amplifier can easily be modified to add a level
shift for applications requiring the single-ended output voltage to be unipolar, i.e., swing between 0V and +2V.
DUAL TRANSIMPEDANCE OUTPUT CONFIGURATION
FIGURE 3. Differential Output Configuration Using an RF
Transformer.
DIFFERENTIAL CONFIGURATION USING AN OP AMP
If the application requires a DC-coupled output, a difference
amplifier may be considered, as shown in Figure 4. Four
external resistors are needed to configure the voltage-feedback op amp OPA680 as a difference amplifier performing
the differential to single-ended conversion. Under the shown
configuration, the DAC902 generates a differential output
signal of 0.5Vp-p at the load resistors, RL. The resistor
values shown were selected to result in a symmetric 25Ω
loading for each of the current outputs since the input
impedance of the difference amplifier is in parallel to resistors RL, and should be considered.
The circuit example of Figure 5 shows the signal output
currents connected into the summing junction of the
OPA2680, which is set up as a transimpedance stage, or
I-to-V converter. With this circuit, the DAC’s output will be
kept at a virtual ground, minimizing the effects of output
impedance variations, which results in the best DC linearity
(INL). However, as mentioned previously, the amplifier
may be driven into slew-rate limitations, and produce unwanted distortion. This may occur especially at high DAC
update rates.
+5V
50Ω
1/2
OPA2680
RF1
DAC902
R2
402Ω
IOUT
R1
200Ω
–VOUT = IOUT • RF
CD1
IOUT
CF1
RF2
DAC902
IOUT
OPA680
COPT
RL
26.1Ω
R3
200Ω
RL
28.7Ω
VOUT
IOUT
CD2
CF2
–5V +5V
R4
402Ω
1/2
OPA2680
–VOUT = IOUT • RF
50Ω
FIGURE 4. Difference Amplifier Provides Differential to
Single-Ended Conversion and DC-Coupling.
–5V
FIGURE 5. Dual, Voltage-Feedback Amplifier OPA2680
Forms Differential Transimpedance Amplifier.
DAC902
SBAS094B
13
The DC gain for this circuit is equal to feedback resistor RF.
At high frequencies, the DAC output impedance (CD1, CD2)
will produce a zero in the noise gain for the OPA2680 that
may cause peaking in the closed-loop frequency response.
CF is added across RF to compensate for this noise-gain
peaking. To achieve a flat transimpedance frequency response, the pole in each feedback network should be set to:
1
GBP
=
2 πR F C F 4 πR F C D
The DAC902 has an on-chip reference circuit that comprises
a 1.24V bandgap reference and a control amplifier. Grounding pin 16, INT/EXT, enables the internal reference operation. The full-scale output current, IOUTFS, of the DAC902 is
determined by the reference voltage, VREF, and the value of
resistor RSET. IOUTFS can be calculated by:
IOUTFS = 32 • IREF = 32 • VREF / RSET
(8)
with GBP = Gain Bandwidth Product of OPA
which will give a corner frequency f-3dB of approximately:
f−3dB =
INTERNAL REFERENCE OPERATION
GBP
2πR F C D
(10)
As shown in Figure 7, the external resistor RSET connects to
the FSA pin (Full-Scale Adjust). The reference control amplifier operates as a V-to-I converter producing a reference
current, IREF, which is determined by the ratio of VREF and
RSET, as shown in Equation 10. The full-scale output current,
IOUTFS, results from multiplying IREF by a fixed factor of 32.
(9)
CCOMPEXT +5V
0.1µF
The full-scale output voltage is simply defined by the product of IOUTFS • RF, and has a negative unipolar excursion. To
improve on the ac performance of this circuit, adjustment of
RF and/or IOUTFS should be considered. Further extensions of
this application example may include adding a differential
filter at the OPA2680’s output followed by a transformer, in
order to convert to a single-ended signal.
IREF =
FSA
RSET
2kΩ
Using a single load resistor connected to the one of the DAC
outputs, a simple current-to-voltage conversion can be accomplished. The circuit in Figure 6 shows a 50Ω resistor
connected to IOUT, providing the termination of the further
connected 50Ω cable. Therefore, with a nominal output
current of 20mA, the DAC produces a total signal swing of
0V to 0.5V into the 25Ω load.
+VA
VREF
RSET
REFIN
SINGLE-ENDED CONFIGURATION
BW
DAC902
Ref
Control
Amp
Current
Sources
CCOMP
400pF
0.1µF
INT/EXT
+1.24V Ref.
FIGURE 7. Internal Reference Configuration.
IOUTFS = 20mA
VOUT = 0V to +0.5V
IOUT
DAC902
50Ω
IOUT
50Ω
25Ω
FIGURE 6. Driving a Doubly-Terminated 50Ω Cable Directly.
Different load resistor values may be selected as long as the
output compliance range is not exceeded. Additionally, the
output current, IOUTFS, and the load resistor may be mutually
adjusted to provide the desired output signal swing and
performance.
14
Using the internal reference, a 2kΩ resistor value results in
a 20mA full-scale output. Resistors with a tolerance of 1%
or better should be considered. Selecting higher values, the
converter output can be adjusted from 20mA down to 2mA.
Operating the DAC902 at lower than 20mA output currents
may be desirable for reasons of reducing the total power
consumption, improving the distortion performance, or observing the output compliance voltage limitations for a given
load condition.
It is recommended to bypass the REFIN pin with a ceramic chip
capacitor of 0.1µF or more. The control amplifier is internally
compensated, and its small signal bandwidth is approximately
3MHz. To improve the ac performance, an additional capacitor
(CCOMPEXT) should be applied between the BW pin and the
analog supply, +VA, as shown in Figure 7. Using a 0.1µF
capacitor, the small-signal bandwidth and output impedance of
the control amplifier is further diminished, reducing the noise
that is fed into the current source array. This also helps
shunting feedthrough signals more effectively, and improving
the noise performance of the DAC902.
DAC902
SBAS094B
EXTERNAL REFERENCE OPERATION
The internal reference can be disabled by applying a logic
HIGH (+VA) to pin INT/EXT. An external reference voltage
can then be driven into the REFIN pin, which in this case
functions as an input, as shown in Figure 8. The use of an
external reference may be considered for applications that
require higher accuracy and drift performance, or to add the
ability of dynamic gain control.
While a 0.1µF capacitor is recommended to be used with the
internal reference, it is optional for the external reference
operation. The reference input, REFIN, has a high input
impedance (1MΩ) and can easily be driven by various
sources. Note that the voltage range of the external reference
should stay within the compliance range of the reference
input (0.1V to 1.25V).
DIGITAL INPUTS
The digital inputs, D0 (LSB) through D11 (MSB) of the
DAC902 accepts standard-positive binary coding. The digital input word is latched into a master-slave latch with the
rising edge of the clock. The DAC output becomes updated
with the following falling clock edge (refer to the specification table and timing diagram for details). The best performance will be achieved with a 50% clock duty cycle,
however, the duty cycle may vary as long as the timing
specifications are met. Additionally, the setup and hold
times may be chosen within their specified limits.
All digital inputs are CMOS compatible. The logic thresholds depend on the applied digital supply voltage such that
they are set to approximately half the supply voltage;
Vth = +VD/2 (±20% tolerance). The DAC902 is designed to
operate over a supply range of 2.7V to 5.5V.
POWER-DOWN MODE
The DAC902 features a power-down function that can be
used to reduce the supply current to less than 9mA over the
specified supply range of 2.7V to 5.5V. Applying a logic
HIGH to the PD pin will initiate the power-down mode,
while a logic LOW enables normal operation. When left
unconnected, an internal active pull-down circuit will enable
the normal operation of the converter.
GROUNDING, DECOUPLING AND
LAYOUT INFORMATION
Proper grounding and bypassing, short lead length, and the
use of ground planes are particularly important for high
frequency designs. Multilayer pc-boards are recommended
for best performance since they offer distinct advantages
such as minimization of ground impedance, separation of
signal layers by ground layers, etc.
The DAC902 uses separate pins for its analog and digital
supply and ground connections. The placement of the decoupling capacitor should be such that the analog supply (+VA)
is bypassed to the analog ground (AGND), and the digital
supply bypassed to the digital ground (DGND). In most
cases 0.1uF ceramic chip capacitors at each supply pin are
adequate to provide a low impedance decoupling path. Keep
in mind that their effectiveness largely depends on the
proximity to the individual supply and ground pins. Therefore, they should be located as close as physically possible
to those device leads. Whenever possible, the capacitors
should be located immediately under each pair of supply/
ground pins on the reverse side of the pc-board. This layout
approach will minimize the parasitic inductance of component leads and pcb runs.
CCOMPEXT +5V
0.1µF
BW
DAC902
IREF =
+VA
VREF
RSET
FSA
REFIN
External
Reference
Ref
Control
Amp
Current
Sources
CCOMP
400pF
RSET
+5V
INT/EXT
+1.24V Ref.
FIGURE 8. External Reference Configuration.
DAC902
SBAS094B
15
Further supply decoupling with surface mount tantalum
capacitors (1uF to 4.7uF) may be added as needed in
proximity of the converter.
Low noise is required for all supply and ground connections
to the DAC902. It is recommended to use a multilayer pcboard utilizing separate power and ground planes. Mixed
signal designs require particular attention to the routing of
the different supply currents and signal traces. Generally,
analog supply and ground planes should only extend into
analog signal areas, such as the DAC output signal and the
reference signal. Digital supply and ground planes must be
confined to areas covering digital circuitry, including the
digital input lines connecting to the converter, as well as the
clock signal. The analog and digital ground planes should be
joined together at one point underneath the DAC. This can
be realized with a short track of approximately 1/8" (3mm).
16
The power to the DAC902 should be provided through the
use of wide pcb runs or planes. Wide runs will present a
lower trace impedance, further optimizing the supply decoupling. The analog and digital supplies for the converter
should only be connected together at the supply connector of
the pc-board. In the case of only one supply voltage being
available to power the DAC, ferrite beads along with bypass
capacitors may be used to create an LC filter. This will
generate a low-noise analog supply voltage that can then be
connected to the +VA supply pin of the DAC902.
While designing the layout, it is important to keep the analog
signal traces separate from any digital line, in order to
prevent noise coupling onto the analog signal path.
DAC902
SBAS094B
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
DAC902E
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902E/2K5
ACTIVE
TSSOP
PW
28
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902E/2K5G4
ACTIVE
TSSOP
PW
28
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902EG4
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902U
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902U/1K
ACTIVE
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902U/1KG4
ACTIVE
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC902UG4
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC902E/2K5
TSSOP
PW
28
2500
330.0
16.4
6.9
10.2
1.8
12.0
16.0
Q1
DAC902U/1K
SOIC
DW
28
1000
330.0
32.4
11.35
18.67
3.1
16.0
32.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC902E/2K5
DAC902U/1K
TSSOP
PW
28
2500
367.0
367.0
38.0
SOIC
DW
28
1000
367.0
367.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated