Delta DCM04S0A0S06NFA Non-isolated point of load dc/dc power modules: 4.5~14vin, 0.69v-5v/20aout Datasheet

DCL12S0A0S20NFA
FEATURES















High efficiency:
93% @ 12Vin, 5V/20A out
92% @ 12Vin, 3.3V/20A out
90% @ 12Vin, 2.5V/20A out
89% @ 12Vin, 1.8V/20A out
83% @ 12Vin, 1.2V/20A out
79% @ 10Vin, 0.69V/20A out
Small size and low profile:
33.02x 13.46x 8.5mm (1.3”x 0.53”x 0.33”)
Surface mount packaging
Standard footprint
Voltage and resistor-based trim
Pre-bias startup
Output voltage tracking
No minimum load required
Output voltage programmable from
0.69Vdc to 5 Vdc via external resistor
Fixed frequency operation and ablity to
Synchronize with external clock
Input UVLO, output OCP
Remote on/off
ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing facility
UL/cUL 60950-1 (US & Canada)
CE mark meets 73/23/EEC and 93/68/EEC
directives
Delphi DCL, Non-Isolated Point of Load
DC/DC Power Modules: 4.5~14Vin,
0.69V-5V/20Aout
The Delphi Series DCL, 4.5-14V input, single output,
OPTIONS

Negative/Positive on/off logic

Vo Tracking feature
non-isolated Point of Load DC/DC converters are the latest
offering from a world leader in power systems technology and
manufacturing -- Delta Electronics, Inc. The DCL series provides
a programmable output voltage from 0.69 V to 5 V using an
external resistor and has flexible and programmable tracking
features to enable a variety of startup voltages as well as tracking
between power modules. This product family is available in
APPLICATIONS

Telecom / DataCom

Distributed power architectures
optimization of component placement, these converters possess

Servers and workstations
outstanding electrical and thermal performance, as well as

LAN / WAN applications
extremely high reliability under highly stressful operating

Data processing applications
surface mount and provides up to 20A of output current in an
industry standard footprint. With creative design technology and
conditions.
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P1
TECHNICAL SPECIFICATIONS
PARAMETER
NOTES and CONDITIONS
DCL12S0A0S20NFA
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Sequencing Voltage
Operating Ambient Temperature
Storage Temperature
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Hysteresis Voltage
Maximum Input Current
No-Load Input Current (Io = 0, module
enabled)
Off Converter Input Current (VIN = 12.0Vdc,
module disabled)
Inrush Transient
Input Reflected Ripple Current, peak-to-peak
Vo ≦ Vin –0.6
Max.
Units
-0.3
-0.3
15
Vin max
V
V
-40
-55
85
125
℃
℃
4.5
14
V
20
V
V
V
A
mA
mA
mA
4.45
4.2
0.25
Vin=4.5V to14V, Io=Io,max
Vin= 10V, Vo,set = 0.69 Vdc
Vin= 12V, Vo,set = 3.3 Vdc
60
74
3
1
(5Hz to 20MHz, 1μH source impedance; Vin =0 to 14V,
Io=Iomax ;
Input Ripple Rejection(120Hz)
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Line(VIN=VIN, min to VIN, max)
Load(Io=Io, min to Io, max)
Temperature(Tref=TA, min to TA, max)
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
Output Short-Circuit Current (Hiccup Mode)
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Settling Time to 10% of Peak Deviation
Turn-On Transient
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Output Voltage Rise Time
Output Capacitive Load
EFFICIENCY
Vo=5.0V
Vo=3.3V
Vo=2.5V
Vo=1.8V
Vo=1.2V
Vo=0.69V
FEATURE CHARACTERISTICS
Switching Frequency
Synchronization Frequency Range
ON/OFF Control, (Negative logic)
Logic Low Voltage
Logic High Voltage
Logic Low Current
Logic High Current
ON/OFF Control, (Positive Logic)
Logic High Voltage
Logic Low Voltage
Logic Low Current
Logic High Current
Tracking Slew Rate Capability
Tracking Delay Time
Tracking Accuracy
GENERAL SPECIFICATIONS
MTBF
Weight
Typ.
with 0.5% tolerance for external resistor used to set
output voltage)
(selected by an external resistor)
For Vo>=2.5V
For Vo<2.5V
For Vo>=2.5V
For Vo<2.5V
For Vo>=2.5V
For Vo<2.5V
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Vin= Vin nominal, Io=Io,min to Io,max, Co= 1µF+10uF
ceramic,
Vin= Vin nominal, Io=Io,min to Io,max, Co= 1µF+10uF
ceramic,
-1.5
mAp-p
45
dB
+1.5
%Vo,set
0.69
Vo,set
5.0
V
-2.5
0.4
10
10
5
0.5
5
+2.5
%Vo,set
mV
Vo,set
mV
mV
%Vo,set
mV
Vo,set
%Vo,set
80
mV
28
mV
20
5
140
2.6
A
% Vo,set
% Io
Adc
380
380
30
mV
mV
µs
2
2
5
ms
ms
ms
µF
0
Io,s/c
10µF Tan & 1µF Ceramic load cap, 2.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
Io=Io.max
Time for Von/off to Vo=10% of Vo,set
Time for Vin=Vin,min to Vo=10% of Vo,set
Time for Vo to rise from 10% to 90% of Vo,set
Full load; ESR ≧0.15mΩ
A2S
43
94
Vin=12V, 100% Load
Vin=12V, 100% Load
Vin=12V, 100% Load
Vin=12V, 100% Load
Vin=12V, 100% Load
Vin=10V, 100% Load
1000
93
92
90
89
83
79
%
%
%
%
%
%
520
500
600
kHz
kHz
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
0
2
1
Vin,max
10
1
V
V
µA
mA
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
Vin-1
Vin,max
3.5
3
25
0.5
V
V
mA
µA
V/msec
ms
mV
mV
Delay from Vin.min to application of tracking voltage
Power-up
0.5V/mS
Power-down 0.5V/mS
10
Io=80% of Io, max; Ta=25°C
100
150
32.51
5.5
M hours
grams
(TA = 25°C, airflow rate = 300 LFM, Vin = 4.5Vdc and 14.0Vdc, nominal Vout unless otherwise noted.)
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P2
ELECTRICAL CHARACTERISTICS CURVES
Figure 1: Converter efficiency vs. output current (Vout= 0.69V)
Figure 2: Converter efficiency vs. output current (1.2V out)
Figure 3: Converter efficiency vs. output current (1.8V out)
Figure 4: Converter efficiency vs. output current (2.5V out)
Figure 5: Converter efficiency vs. output current 3.3V out)
Figure 6: Converter efficiency vs. output current (5.0V out)
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P3
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 7: Output ripple & noise at 7Vin, 0.69V/20A out
Figure 8: Output ripple & noise at 12Vin, 1.8V/20A out
CH1:VOUT, 20mV/div, 1uS/div
CH1:VOUT, 20mV/div, 1uS/div
Figure 9: Output ripple & noise at 12Vin, 3.3V/20A out
Figure 10: Output ripple & noise at 12Vin, 5.0V/20A out
CH1:VOUT, 20mV/div, 1uS/div
CH1:VOUT, 20mV/div, 1uS/div
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P4
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 11: Turn on delay time at 7Vin, 0.69V/20A out.
Figure 12: Turn on delay time at 12Vin, 1.8V/20A out.
(Green : VOUT, 0.5V/div, Yellow: VIN, 2V/div. 2mS/div)
(Green : VOUT, 0.5V/div, Yellow: VIN, 5V/div. 2mS/div)
(Yellow : VOUT, 0.2V/div, Green: VIN, 5V/div. 2mS/div)
Figure 13: Turn on delay time at 12Vin, 3.3V/20A out.
Figure 14: Turn on delay time at 12Vin, 5.0V/20A out.
(Green : VOUT, 1V/div, Yellow: VIN, 5V/div. 2mS/div)
(Green : VOUT, 2V/div, Yellow: VIN, 5V/div. 2mS/div)
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P5
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 15: Turn on delay time at remote on 7Vin, 0.69V/20A out.
Figure16: Turn on delay time at remote on 12Vin, 1.8V/20A out.
(Yellow: VOUT, 0.5V/div, Green: ON/OFF, 2V/div, 2mS/div)
(Yellow: VOUT, 0.5V/div, Green: ON/OFF, 2V/div, 2mS/div)
Figure 17: Turn on delay time at remote on 12Vin, 3.3V/20A out.
Figure 18: Turn on delay time at remote on 12Vin, 5.0V/20A out.
(Yellow: VOUT, 1V/div, Green: ON/OFF, 2V/div, 2mS/div)
(Yellow: VOUT, 2V/div, Green: ON/OFF, 2V/div, 2mS/div)
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P6
ELECTRICAL CHARACTERISTICS CURVES
Figure 19: Transient response to dynamic load change at
Figure 20: Transient response to dynamic load change at
2.5A/μS from 50%~ 100%~50% of Io, max at 7Vin, 0.69Vout
2.5A/μS from 50%~ 100%~50% of Io, max at 12Vin, 1.8Vout
(Cout = 1uF ceramic, 47uF*2 +10μFceramic)
(Cout = 1uF ceramic, 47uF*2 +10μFceramic)
Yellow : VOUT, 0.2V/div, 100uS/div
Yellow : VOUT, 0.2V/div, 100uS/div
Figure 21: Transient response to dynamic load change at
Figure 22: Transient response to dynamic load change at
2.5A/μS from 50%~ 100%~50% of Io, max at 12Vin, 3.3Vout
2.5A/μS from 50%~ 100%~50% of Io, max at 12Vin, 5Vout
(Cout = 1uF ceramic, 47uF*2 +10μFceramic)
(Cout = 1uF ceramic, 47uF*2 +10μFceramic)
Yellow : VOUT, 0.2V/div, 100uS/div
Yellow : VOUT, 0.2V/div, 100uS/div
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P7
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 23: Tracking function, Vtracking=6V, Vout= 5.0V, full load
Figure 24:Tracking function, Vtracking=6V, Vout= 5.0V, full load
Yellow : VOUT, (1V/div), Green: Tracking, (1V/div), 500uS/div
Yellow : VOUT, (1V/div), Green: Tracking, (1V/div), 10mS/div
Figure 25: Tracking function, Vtracking=0.8V, Vout=0.69V, full load
Figure 26:Tracking function, Vtracking=0.8V, Vout= 0.69V, full load
Yellow: VOUT, 0.2V/div, Green : Tracking, 0.2V/div, 1mS/div
Yellow: VOUT, 0.2V/div, Green : Tracking, 0.2V/div, 5mS/div
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P8
TEST CONFIGURATIONS
DESIGN CONSIDERATIONS
Input Source Impedance
To maintain low noise and ripple at the input voltage, it is
critical to use low ESR capacitors at the input to the module. A
highly inductive source can affect the stability of the module.
An input capacitance must be placed close to the modules
input pins to filter ripple current and ensure module stability in
the presence of inductive traces that supply the input voltage to
the module.
Safety Considerations
Figure 27: Input reflected-ripple current test setup
For safety-agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the input
must meet SELV requirements. The power module has
extra-low voltage (ELV) outputs when all inputs are ELV.
Note: Use a 10μF and 1μF capacitor. Scope measurement
should be made using a BNC connector.
The input to these units is to be provided with a fast acting fuse
with a maximum rating of 30A in the positive input lead.
Figure 28: Peak-peak output noise and startup transient
measurement test setup.
VI
Vo
GND
Figure 29: Output voltage and efficiency measurement test
setup
Note: All measurements are taken at the module terminals.
When the module is not soldered (via socket), place
Kelvin connections at module terminals to avoid
measurement errors due to contact resistance.
(
Vo  Io
)  100 %
Vi  Ii
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P9
FEATURES DESCRIPTIONS
Input Under voltage Lockout
At input voltages below the input under voltage lockout limit, the
Remote On/Off
module operation is disabled. The module will begin to operate at
The DCL series power modules have an On/Off pin for remote
an input voltage above the under voltage lockout turn-on threshold.
On/Off operation. Both positive and negative On/Off logic
options are available in the DCL series power modules.
Over-Current Protection
To provide protection in an output over load fault condition, the unit
For positive logic module, connect an open collector (NPN)
transistor or open drain (N channel) MOSFET between the
On/Off pin and the GND pin (see figure 30). Positive logic On/Off
is equipped with internal over-current protection. When the
over-current protection is triggered, the unit enters hiccup mode.
The units operate normally once the fault condition is removed.
signal turns the module ON during the logic high and turns the
module OFF during the logic low. When the positive On/Off
Remote Sense
function is not used, leave the pin floating or tie to Vin (module
The DCL provide Vo remote sensing to achieve proper regulation
will be On).
at the load points and reduce effects of distribution losses on
For negative logic module, the On/Off pin is pulled high with an
output line. In the event of an open remote sense line, the module
external pull-up 5kΩ resistor (see figure 31). Negative logic
shall maintain local sense regulation through an internal resistor.
On/Off signal turns the module OFF during logic high and turns
The module shall correct for a total of 0.5V of loss. The remote
the module ON during logic low. If the negative On/Off function
sense line impedance shall be < 10.
is not used, leave the pin floating or tie to GND. (module will be
Distribution Losses
on)
Vo
Vin
Vo
V in
Distribution Losses
Sense
RL
I O N /O F F
O n/O ff
RL
Q1
GND
GND
Distribution
Losses
Figure 30: Positive remote On/Off implementation
Distribution
Losses
Figure 32: Effective circuit configuration for remote sense
operation
Vo
Vin
Rpullup
I O N /O FF
On/Off
RL
Q1
GND
Figure 31: Negative remote On/Off implementation
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P10
FEATURES DESCRIPTIONS (CON.)
Table 1 provides Rtrim values required for some common
output voltages. By using a ±0.5% tolerance trim resistor with a
Output Voltage Programming
TC of
±100ppm, a set point tolerance of ±1.5% can be achieved as
The output voltage of the DCL can be programmed to any
specified in the electrical specification.
voltage between 0.69Vdc and 5.5Vdc by connecting one resistor
(shown as Rtrim in Figure 33) between the TRIM and GND pins
of the module. Without this external resistor, the output voltage of
the module is 0.69 Vdc. To calculate the value of the resistor
Rtrim for a particular output voltage Vo, please use the following
equation:
 6.9 
Rtrim  
 K
Vo  0.69 
Rtrim is the external resistor in kΩ
Vo is the desired output voltage.
Certain restrictions apply on the output voltage set point
For example, to program the output voltage of the DCL module to
depending on the input voltage. These are shown in the Output
5.0Vdc, Rtrim is calculated as follows:
Voltage vs. Input Voltage Set Point Area plot in Fig. 34.
 6.9 
Rtrim  
 K  1.601K
 5.0  0.69 
The Upper Limit curve shows that for output voltages of 0.9V
and lower, the input voltage must be lower than the maximum
of 14V.
The Lower Limit curve shows that for output voltages of 3.3V
and higher, the input voltage needs to be larger than the
minimum of 4.5V
Figure 33: Circuit configulation for programming output voltage
using an external resister.
Figure 34: Output voltage vs input voltage setpoint area plot
showing limits were the output can be set for different.input
voltage.
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P11
FEATURE DESCRIPTIONS (CON.)
Voltage Margining
When an analog voltage is applied to the SEQ pin, the output
voltage tracks this voltage until the output reaches the
set-point voltage. The final value of the SEQ voltage must be
Output voltage margining can be implemented in the DCL
modules by connecting a resistor, R margin-up, from the Trim pin
to the ground pin for margining-up the output voltage and by
connecting a resistor, Rmargin-down, from the Trim pin to the
output pin for margining-down. Figure 35 shows the circuit
configuration for output voltage margining. If unused, leave the
trim pin unconnected. A calculation tool is available from the
evaluation procedure which computes the values of Rmargin-up
and Rmargin-down for a specific output voltage and margin
percentage.
set higher than the set-point voltage of the module. The output
voltage follows the voltage on the SEQ pin on a one-to-one
basis. By connecting multiple modules together, multiple
modules can track their output voltages to the voltage applied
on the SEQ pin.
For proper voltage sequencing, first, input voltage is applied to
the module. The On/Off pin of the module is left unconnected
(or tied to GND for negative logic modules or tied to VIN for
positive logic modules) so that the module is ON by default.
After applying input voltage to the module, a minimum 10msec
delay is required before applying voltage on the SEQ pin. This
delay gives the module enough time to complete its internal
power-up soft-start cycle. During the delay time, the SEQ pin
should be held close to ground (nominally 50mV ± 20 mV).
This is required to keep the internal op-amp out of saturation
thus preventing output overshoot during the start of the
sequencing ramp. By selecting resistor R1 (see Figure. 37)
according to the following equation
 24950 
R1  

Vin  0.05 
Figure 35: Circuit configuration for output voltage margining
Output Voltage Sequencing
The DCL 12V 20A modules include a sequencing feature,
EZ-SEQUENCE that enables users to implement various types of
output voltage sequencing in their applications. This is
Figure 36: Sequential Start-up
accomplished via an additional sequencing pin. When not using
the sequencing feature, either tie the SEQ pin to VIN or leave it
The voltage at the sequencing pin will be 50mV when the
unconnected.
sequencing signal is at zero.
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P12
FEATURE DESCRIPTIONS (CON.)
Power Good
The DCL modules provide a Power Good (PGOOD) signal
After the 10msec delay, an analog voltage is applied to the SEQ
that is implemented with an open-drain output to indicate that
pin and the output voltage of the module will track this voltage on
the output voltage is within the regulation limits of the power
a one-to-one volt bases until the output reaches the set-point
module. The PGOOD signal will be de-asserted to a low state
voltage. To initiate simultaneous shutdown of the modules, the
if any condition such as over temperature, over current or loss
SEQ pin voltage is lowered in a controlled manner. The output
of regulation occurs that would result in the output voltage
voltage of the modules tracks the voltages below their set-point
going ±10% outside the set point value. The PGOOD terminal
voltages on a one-to-one basis. A valid input voltage must be
should be connected through a pull up resistor (suggested
maintained until the tracking and output voltages reach ground
value 100KΩ) to a source of 5VDC or lower.
potential.
When using the EZ-SEQUENCETM feature to control start-up
of the module, pre-bias immunity during startup is disabled. The
Monotonic Start-up and Shutdown
pre-bias immunity feature of the module relies on the module
being in the diode-mode during start-up. When using the
The DCL 20A modules have monotonic start-up and shutdown
EZ-SEQUENCETM feature, modules goes through an internal
behavior for any combination of rated input voltage, output
set-up time of 10msec, and will be in synchronous rectification
current and operating temperature range.
mode when the voltage at the SEQ pin is applied. This will result
in the module sinking current if a pre-bias voltage is present at
the output of the module.
Synchronization
The DCL 20A modules can be synchronized using an external
signal. Details of the SYNC signal are provided in below table.
If the synchronization function is not being used, leave the
SYNC pin floating.
Figure 37: Circuit showing connection of the sequencing signal
to the SEQ pin.
Simultaneous
DS_DCL12S0A0S20NFA_11152012
Simultaneous tracking (Figure 41) is implemented by using the
TRACK pin. The objective is to minimize the voltage
difference between the power supply outputs during power up
E-mail: [email protected]
http://www.deltaww.com/dcdc
P13
THERMAL CONSIDERATIONS
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient cooling
THERMAL CURVES
AIRFLOW
of the power module is needed over the entire temperature
range of the module. Convection cooling is usually the
dominant mode of heat transfer.
Hence, the choice of equipment to characterize the thermal
performance of the power module is a wind tunnel.
Figure 39: Temperature measurement location
The allowed maximum hot spot temperature is defined at 117℃
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in heated
vertical wind tunnels that simulate the thermal environments
Output Current(A)
encountered in most electronics equipment. This type of
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 12V, Vo=5.0V (Airflow From Pin10 To Pin8)
20
equipment commonly uses vertically mounted circuit cards in
cabinet racks in which the power modules are mounted.
Natural
Convection
16
100LFM
The following figure shows the wind tunnel characterization
12
200LFM
setup. The power module is mounted on a test PWB and is
vertically positioned within the wind tunnel.
300LFM
8
400LFM
Thermal Derating
4
Heat can be removed by increasing airflow over the module.
0
25
To enhance system reliability, the power module should
always be operated below the maximum operating
temperature. If the temperature exceeds the maximum module
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 40: Output current vs. ambient temperature and air
velocity@Vin=12V, Vout=5.0V(Either Orientation)
temperature, reliability of the unit may be affected.
Output Current(A)
PWB
FANCING PWB
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 12V, Vo=3.3V (Airflow From Pin10 To Pin8)
20
MODULE
Natural
Convection
16
100LFM
200LFM
12
300LFM
50.8(2.00")
AIR VELOCITY
AND AMBIENT
TEMPERATURE
SURED BELOW
THE MODULE
400LFM
8
4
AIR FLOW
0
25
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 41: Output current vs. ambient temperature and air
velocity@Vin=12V, Vout=3.3V(Either Orientation)
Figure 38: Wind tunnel test setup
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P14
THERMAL CURVES
Output Current(A)
THERMAL CURVES
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 12V, Vo=2.5V (Airflow From Pin10 To Pin8)
20
Output Current(A)
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 7V, Vo=0.69V (Airflow From Pin10 To Pin8)
20
Natural
Convection
Natural
Convection
16
16
100LFM
100LFM
12
12
200LFM
300LFM
8
8
400LFM
4
4
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 42: Output current vs. ambient temperature and air
velocity@Vin=12V, Vout=2.5V(Either Orientation)
Output Current(A)
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient
Temperature
(℃)
Figure 45: Output current vs. ambient temperature and air
velocity@Vin=7V, Vout=0.69V(Either Orientation)
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 12V, Vo=1.8V (Airflow From Pin10 To Pin8)
20
16
Natural
Convection
12
100LFM
200LFM
300LFM
8
4
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 43: Output current vs. ambient temperature and air
velocity@Vin=12V, Vout=1.8V(Either Orientation)
Output Current(A)
DCL12S0A0S20NFA Output Current vs. Ambient Temperature and Air Velocity
@Vin = 12V, Vo=1.2V (Airflow From Pin10 To Pin8)
20
Natural
Convection
16
100LFM
12
200LFM
8
4
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 44: Output current vs. ambient temperature and air
velocity@Vin=12V, Vout=1.2V(Either Orientation)
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P15
PICK AND PLACE LOCATION
RECOMMENDED PAD LAYOUT
SURFACE-MOUNT TAPE & REEL
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P16
LEAD (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE
Note: The temperature refers to the pin of DCL, measured on the pin Vout joint.
LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE
Temp.
Peak Temp. 240 ~ 245 ℃
220℃
Ramp down
max. 4℃ /sec.
200℃
150℃
Preheat time
90~120 sec.
Time Limited 75 sec.
above 220℃
Ramp up
max. 3℃ /sec.
25℃
Time
Note: The temperature refers to the pin of DCL, measured on the pin Vout joint..
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P17
MECHANICAL DRAWING
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P18
PART NUMBERING SYSTEM
DCL
12
S
0A0
S
20
N
Product
Series
Input
Voltage
Numbers
of Outputs
Output
Voltage
Package
Type
Output
Current
On/Off
logic
DCT-3A
DCS - 6A
DCM - 12A
DCL - 20A
04 - 2.4~5.5V
12 – 4.5~14V
S - Single
0A0 S - SMD
Programmable
03-3A
06 - 6A
12 - 12A
20 - 20A
F
N- negative
P- positive
A
Option Code
F- RoHS 6/6
(Lead Free)
A - Standard Function
MODEL LIST
Model Name
Packaging
Input Voltage
Output Voltage
Output Current
Efficiency
12Vin, 5Vdc @ 20A
DCL12S0A0S20NFA
SMD
4.5V ~ 14Vdc
0.69V~ 5.0Vdc
20A
93.0%
CONTACT: www.deltaww.com/dcdc
USA:
Telephone:
East Coast: 978-656-3993
West Coast: 510-668-5100
Fax: (978) 656 3964
Email: [email protected]
Europe:
Telephone: +31-20-655-0967
Fax: +31-20-655-0999
Email: [email protected]
Asia & the rest of world:
Telephone: +886 3 4526107 x6220~6224
Fax: +886 3 4513485
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available
upon request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by
Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use.
No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right
to revise these specifications at any time, without notice.
DS_DCL12S0A0S20NFA_11152012
E-mail: [email protected]
http://www.deltaww.com/dcdc
P19
Similar pages