Dynex DCR2630Y48 Phase control thyristor Datasheet

DCR2630Y52
Phase Control Thyristor
Preliminary Information
DS5901-2 November 2010 (LN27694)
FEATURES
KEY PARAMETERS

Double Side Cooling

High Surge Capability
VDRM
IT(AV)
ITSM
dV/dt*
dI/dt
APPLICATIONS
5200V
2630A
36700A
1500V/µs
300A/µs
* Higher dV/dt selections available

High Power Drives

High Voltage Power Supplies

Static Switches
VOLTAGE RATINGS
Part and
Ordering
Number
DCR2630Y52*
DCR2630Y50
DCR2630Y48
Repetitive Peak
Voltages
VDRM and VRRM
V
5200
5000
4800
Conditions
Tvj = -40°C to 125°C,
IDRM = IRRM = 200mA,
VDRM, VRRM tp = 10ms,
VDSM & VRSM =
VDRM & VRRM + 100V
respectively
Lower voltage grades available.
0
0
* 5000V @ -40 C, 5200V °0 C
ORDERING INFORMATION
When ordering, select the required part number
shown in the Voltage Ratings selection table.
Outline type code: Y
For example:
(See Package Details for further information)
DCR2630Y52
Fig. 1 Package outline
Note: Please use the complete part number when ordering
and quote this number in any future correspondence
relating to your order.
1/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
CURRENT RATINGS
Tcase = 60°C unless stated otherwise
Symbol
Parameter
Test Conditions
Max.
Units
2630
A
Double Side Cooled
IT(AV)
Mean on-state current
IT(RMS)
RMS value
-
4131
A
Continuous (direct) on-state current
-
3810
A
IT
Half wave resistive load
SURGE RATINGS
Symbol
ITSM
2
It
Parameter
Surge (non-repetitive) on-state current
Test Conditions
Max.
Units
10ms half sine, Tcase = 125°C
36.7
kA
VR = 0
6.73
MA s
Min.
Max.
Units
2
I t for fusing
2
THERMAL AND MECHANICAL RATINGS
Symbol
Rth(j-c)
Rth(c-h)
Parameter
Thermal resistance – junction to case
Thermal resistance – case to heatsink
Test Conditions
Double side cooled
DC
-
0.00835
°C/W
Single side cooled
Anode DC
-
0.0134
°C/W
Cathode DC
-
0.023
°C/W
Double side
-
0.002
°C/W
-
0.004
°C/W
-
125
°C
Clamping force 54kN
(with mounting compound)
Blocking VDRM / VRRM
Single side
Tvj
Virtual junction temperature
Tstg
Storage temperature range
-55
125
°C
Fm
Clamping force
48.0
59.0
kN
2/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
DYNAMIC CHARACTERISTICS
Symbol
IRRM/IDRM
Parameter
Test Conditions
Min.
Max.
Units
Peak reverse and off-state current
At VRRM/VDRM, Tcase = 125°C
-
200
mA
dV/dt
Max. linear rate of rise of off-state voltage
To 67% VDRM, Tj = 125°C, gate open
-
1500
V/µs
dI/dt
Rate of rise of on-state current
From 67% VDRM to 2x IT(AV)
Repetitive 50Hz
-
150
A/µs
Gate source 30V, 10,
Non-repetitive
-
300
A/µs
tr < 0.5µs, Tj = 125°C
VT(TO)
rT
tgd
Threshold voltage – Low level
500A to 2000A at Tcase = 125°C
-
0.90
V
Threshold voltage – High level
2000A to 7200A at Tcase = 125°C
-
1.1
V
On-state slope resistance – Low level
500A to 2000A at Tcase = 125°C
-
0.3428
m
On-state slope resistance – High level
2000A to 7200A at Tcase = 125°C
-
0.2414
m
VD = 67% VDRM, gate source 30V, 10
-
3
µs
-
600
µs
Delay time
tr = 0.5µs, Tj = 25°C
tq
Turn-off time
Tj = 125°C, VR = 200V, dI/dt = 1A/µs,
dVDR/dt = 20V/µs linear
QS
Stored charge
IT = 2000A, Tj = 125°C, dI/dt – 1A/µs,
IL
Latching current
Tj = 25°C, VD = 5V
-
3
A
IH
Holding current
Tj = 25°C, RG-K = , ITM = 500A, IT = 5A
-
300
mA
2000
4750
µC
3/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
GATE TRIGGER CHARACTERISTICS AND RATINGS
Symbol
Parameter
Test Conditions
Max.
Units
VGT
Gate trigger voltage
VDRM = 5V, Tcase = 25°C
1.5
V
VGD
Gate non-trigger voltage
At 50% VDRM, Tcase = 125°C
0.4
V
IGT
Gate trigger current
VDRM = 5V, Tcase = 25°C
250
mA
IGD
Gate non-trigger current
At 50% VDRM, Tcase = 125°C
15
mA
CURVES
Instantaneous on-state current IT - (A)
7000
6000
5000
4000
3000
2000
min 125°C
max 125°C
min 25°C
max 25°C
1000
0
0.6
1.0
1.4
1.8
2.2
2.6
3.0
Instantaneous on-state voltage VT - (V)
Fig.2 Maximum & minimum on-state characteristics
VTM EQUATION
VTM = A + Bln (IT) + C.IT+D.IT
Where
A = - 0.450546
B = 0.251217
C = 0.000242
D = - 0.008134
these values are valid for Tj = 125°C for IT 500A to 7200A
4/10
www.dynexsemi.com
DCR2630Y52
11
130
10
120
Maximum case temperature, T case ( o C )
Mean power dissipation - (kW)
SEMICONDUCTOR
9
8
7
6
5
4
180
3
120
90
2
60
1
180
120
90
60
30
110
100
90
80
70
60
50
40
30
20
10
30
0
0
0
1000
2000
3000
4000
0
1000
2000
3000
4000
Mean on-state current, IT(AV) - (A)
Mean on-state current, IT(AV) - (A)
Fig.3 On-state power dissipation – sine wave
Fig.4 Maximum permissible case temperature,
double side cooled – sine wave
180
120
90
60
30
120
110
100
12
11
Mean power dissipation - (kW)
Maximum heatsink temperature, THeatsink - ( ° C)
130
90
80
70
60
50
40
30
20
10
10
9
8
7
6
d.c.
5
180
4
120
90
3
60
2
30
1
0
0
1000
2000
3000
4000
Mean on-state current, IT(AV) - (A)
Fig.5 Maximum permissible heatsink temperature,
double side cooled – sine wave
0
0
1000
2000
3000
4000
5000
Mean on-state current, IT(AV) - (A)
Fig.6 On-state power dissipation – rectangular wave
5/10
www.dynexsemi.com
DCR2630Y52
130
130
d.c.
120
Maximum heatsink temperature Theatsink -(o C)
Maximum permissible case temperature , Tcase -(° C)
SEMICONDUCTOR
180
110
120
100
90
90
60
30
80
70
60
50
40
30
20
10
d.c.
120
180
110
120
90
100
60
90
30
80
70
60
50
40
30
20
10
0
0
0
1000
2000
3000
4000
5000
6000
0
Mean on-state current, IT(AV) - (A)
Fig.7 Maximum permissible case temperature,
double side cooled – rectangular wave
1000
2000
1
0.612
Double side cooledRi (°C/kW)
Thermal Impedance, Zth(j-c) - ( °C/kW)
4000
5000
Fig.8 Maximum permissible heatsink temperature,
double side cooled – rectangular wave
25
Ti (s)
Anode side cooled Ri (°C/kW)
20
3000
Mean on-state current, IT(AV) - (A)
Double Side Cooling
Ti (s)
Ri (°C/kW)
Cathode side cooled
Anode Side Cooling
15
4
2.8608
0.010332 0.056415 0.333082
1.6323
3.61
7.1383
0.011328 0.065993 0.419695
9.0612
0.6728
Ti (s)
Cathode Sided Cooling
3
3.1053
0.7009
2
1.7721
1.9388
2.0168
0.010954 0.065544
1.7306 18.6391
0.30379
5.7274
Zth =  [Ri x ( 1-exp. (t/ti))] [1]
10
Rth(j-c) Conduction
Tables show the increments of thermal resistance R th(j-c) when the device
operates at conduction angles other than d.c.
5
0
0.001
0.01
0.1
1
Time ( s )
10
100
Double side cooling
Zth (z)
sine.
rect.
°
180
0.94
0.65
120
1.09
0.92
90
1.24
1.07
60
1.38
1.23
30
1.49
1.40
15
1.54
1.49
Anode Side Cooling
Zth (z)
sine.
rect.
°
180
0.94
0.64
120
1.08
0.91
90
1.23
1.06
60
1.37
1.22
30
1.47
1.38
15
1.52
1.47
Cathode Sided Cooling
Zth (z)
sine.
rect.
°
180 0.94
0.64
120 1.08
0.91
90
1.24
1.06
60
1.37
1.22
30
1.48
1.39
15
1.53
1.48
Fig.9 Maximum (limit) transient thermal impedance – junction to case (°C/kW)
6/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
Fig.10 Multi-cycle surge current
Fig.11 Single-cycle surge current
600
20000
18000
Reverse recovery current. IRR - (A)
QSmax
=4737.8*(di/dt)0.4604
Stored Charge, QS - (uC)
16000
QSmin
=2053.4*(di/dt)0.5824
14000
12000
10000
8000
6000
Conditions:
Tj = 125oC, VRpeak ~ 3100V
VRM ~ 2100V
snubber as appopriate to
control reverse volts
4000
2000
500
IRRmax
= 58.357*(di/dt)0.7168
400
300
IRRmin
= 37.083*(di/dt)0.7817
200
Conditions:
Tj = 125oC, VRpeak ~ 3100V
VRM ~ 2100V
snubber as appropriate to
control reverse volts
100
0
0
0
10
20
30
Rate of decay of on-state current, di/dt - (A/us)
Fig.12 Stored charge
0
5
10
15
20
25
Rate of decay of on-state current, di/dt - (A/us)
Fig.13 Reverse recovery current
7/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
10
Gate trigger voltage, VGT - (V)
9
Pulse
Width us
100
200
500
1000
10000
8
7
Pulse Power PGM (Watts)
Frequency Hz
50
100
150
150
150
150
150
150
150
100
20
-
400
150
125
100
25
-
Upper Limit
6
5
Preferred gate drive area
4
3
2
Tj = -40oC
Tj = 25oC
Lower Limit
Tj = 125oC
1
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Gate trigger current IGT, - (A)
Fig14 Gate Characteristics
30
Lower Limit
Upper Limit
5W
10W
20W
50W
100W
150W
-40C
Gate trigger voltage, VGT - (V)
25
20
15
10
5
0
0
1
2
3
4
5
6
7
8
9
10
Gate trigger current, IGT - (A)
Fig. 15 Gate characteristics
8/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
PACKAGE DETAILS
For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
3rd ANGLE PROJECTION
DO NOT SCALE
IF IN DOUBT ASK
HOLE Ø3.60 X 2.00
DEEP (IN BOTH
ELECTRODES)
20° OFFSET (NOM.)
TO GATE TUBE
Device
DCR1474SY18
DCR1475SY28
DCR1476SY42
DCR1478SY48
DCR1574SY28
DCR1575SY42
DCR1576SY52
DCR3910Y22
DCR3650Y28
DCR2930Y42
DCR2630Y52
DCR2220Y65
DCR1840Y85
Maximum Minimum
Thickness Thickness
(mm)
(mm)
35.045
34.395
35.12
34.47
35.35
34.7
35.47
34.82
35.12
34.47
35.35
34.7
35.47
34.82
35.045
34.395
35.12
34.47
35.35
34.7
35.47
34.82
35.73
35.08
36.09
35.44
Ø112.5 MAX.
Ø73.0 NOM.
Ø1.5
CATHODE
GATE
ANODE
Ø73.0 NOM.
FOR PACKAGE HEIGHT
SEE TABLE
Lead length: 420mm
Lead terminal connector: M4 ring
Package outline type code: Y
Fig.16 Package outline
9/10
www.dynexsemi.com
DCR2630Y52
SEMICONDUCTOR
IMPORTANT INFORMATION:
This publication is provided for information only and not for resale.
The products and information in this publication are intended for use by appropriately trained technical personnel.
Due to the diversity of product applications, the information contained herein is provided as a general guide only and does not constitute
any guarantee of suitability for use in a specific application.The user must evaluate the suitability of the product and the completeness of
the product data for the application. The user is responsible for product selection and ensuring all safety and any warning requirements
are met. Should additional product information be needed please contact Customer Service.
Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or typographical
errors. The information is provided without any warranty or guarantee of any kind.
This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it is the
most up to date version and has not been superseded.
The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to property.
The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a product failure or
malfunction.
The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use
protective safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any
electric charge remaining in the product must be discharged and allowed to cool before safe handling using protective gloves.
Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use outside the
product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all semiconductors, this may include
potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or explosion. Appropriate application design
and safety precautions should always be followed to protect persons and property.
Product Status & Product Ordering:
We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for
production. The annotations are as follows:Target Information:
Preliminary Information:
No Annotation:
This is the most tentative form of information and represents a very preliminary specification.
No actual design work on the product has been started.
The product design is complete and final characterisation for volume production is in
progress.The datasheet represents the product as it is now understood but details may change.
The product has been approved for production and unless otherwise notified by Dynex any
product ordered will be supplied to the current version of the data sheet prevailing at the
time of our order acknowledgement.
All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available on request.
Any brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
HEADQUARTERS OPERATIONS
CUSTOMER SERVICE
DYNEX SEMICONDUCTOR LIMITED
Doddington Road, Lincoln, Lincolnshire, LN6 3LF
United Kingdom.
Phone: +44 (0) 1522 500500
Fax:
+44 (0) 1522 500550
Web: http://www.dynexsemi.com
Phone: +44 (0) 1522 502753 / 502901
Fax:
+44 (0) 1522 500020
e-mail: [email protected]
 Dynex Semiconductor Ltd.
Technical Documentation – Not for resale.
10/10
www.dynexsemi.com
Similar pages