Data Delay DDU66F-150D1 5-tap, ttl-interfaced fixed delay line (series ddu66f) Datasheet

DDU66F
data 3 
delay
devices, inc.
5-TAP, TTL-INTERFACED
FIXED DELAY LINE
(SERIES DDU66F)
FEATURES
•
•
•
•
•
•
PACKAGES
Five equally spaced outputs
Fits standard 14-pin DIP socket
Low profile
Auto-insertable
Input & outputs fully TTL interfaced & buffered
IN
1
T2
4
T4
6
GND
7
14
VCC
12
T1
10
T3
8
T5
IN
N/C
N/C
T2
N/C
T4
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VCC
N/C
T1
N/C
T3
N/C
T5
2
10 T L fan-out capability
DDU66F-xx
DIP
DDU66F-xxA2 Gull-Wing
DDU66F-xxB2 J-Lead
DDU66F-xxME7 Military DIP
FUNCTIONAL DESCRIPTION
DDU66F-xxD1
DDU66F-xxD4
DDU66F-xxMD1
DDU66F-xxMD4
Com. SMD
Com. SMD
Mil. SMD
Mil. SMD
PIN DESCRIPTIONS
The DDU66F-series device is a 5-tap digitally buffered delay line. The
IN
Signal Input
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
T1-T5 Tap Outputs
amount given by the device dash number. For dash numbers less than 25,
VCC
+5 Volts
the total delay of the line is measured from T1 to T5, with the nominal value
GND Ground
given by the dash number. The nominal tap-to-tap delay increment is
given by 1/4 of this number. The inherent delay from IN to T1 is nominally 3.5ns. For dash numbers
greater than or equal to 25, the total delay of the line is measured from IN to T5, with the nominal value
given by the dash number. The nominal tap-to-tap delay increment is given by 1/5 of this number.
SERIES SPECIFICATIONS
DASH NUMBER SPECIFICATIONS
•
•
•
•
Part
Number
DDU66F-4
DDU66F-6
DDU66F-8
DDU66F-10
DDU66F-12
DDU66F-16
DDU66F-20
DDU66F-25
DDU66F-30
DDU66F-35
DDU66F-40
DDU66F-45
DDU66F-50
DDU66F-60
DDU66F-75
DDU66F-100
DDU66F-125
DDU66F-150
DDU66F-175
DDU66F-200
DDU66F-250
•
•
Minimum input pulse width: 40% of total delay
Output rise time: 2ns typical
Supply voltage: 5VDC ± 5%
Supply current: ICCL = 32ma typical
ICCH = 7ma typical
Operating temperature: 0° to 70° C
Temp. coefficient of total delay: 100 PPM/°C
3.5ns
VCC IN
25%
T1
25%
T2
25%
T3
25%
T4
T5 GND
Functional diagram for dash numbers < 25
20%
VCC IN
20%
T1
20%
T2
20%
T3
20%
T4
Doc #97020
2/5/97
Delay Per
Tap (ns)
1.0 ± 0.5
1.5 ± 0.5
2.0 ± 1.0
2.5 ± 1.0
3.0 ± 1.0
4.0 ± 1.5
5.0 ± 1.5
5.0 ± 2.0
6.0 ± 2.0
7.0 ± 2.0
8.0 ± 2.0
9.0 ± 3.0
10.0 ± 3.0
12.0 ± 3.0
15.0 ± 3.0
20.0 ± 3.0
25.0 ± 3.0
30.0 ± 3.0
35.0 ± 4.0
40.0 ± 4.0
50.0 ± 5.0
T5 GND
Functional diagram for dash numbers >= 25
 1997 Data Delay Devices
Total
Delay (ns)
4 ± 1.0 *
6 ± 1.0 *
8 ± 2.0 *
10 ± 2.0 *
12 ± 2.0 *
16 ± 2.0 *
20 ± 3.0 *
25 ± 3.0
30 ± 3.0
35 ± 3.0
40 ± 3.0
45 ± 3.0
50 ± 3.0
60 ± 3.0
75 ± 4.0
100 ± 5.0
125 ± 6.5
150 ± 7.5
175 ± 8.0
200 ± 10.0
250 ± 12.5
* Total delay is referenced to first tap output
Input to first tap = 3.5ns ± 1ns
NOTE: Any dash number between 4 and 250 not
shown is also available.
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
1
DDU66F
APPLICATION NOTES
Delay Devices if your application requires device
testing at a specific input condition.
HIGH FREQUENCY RESPONSE
The DDU66F tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 40% of the total delay and periods as
small as 80% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
POWER SUPPLY BYPASSING
The DDU66F relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VCC to GND,
located as close as possible to the VCC pin, is
recommended. A wide VCC trace and a clean
ground plane should be used.
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Supply Voltage
Input Pin Voltage
Storage Temperature
Lead Temperature
SYMBOL
VCC
VIN
TSTRG
TLEAD
MIN
-0.3
-0.3
-55
MAX
7.0
VCC+0.3
150
300
UNITS
V
V
C
C
NOTES
10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER
High Level Output Voltage
SYMBOL
VOH
Low Level Output Voltage
VOL
High Level Output Current
Low Level Output Current
High Level Input Voltage
Low Level Input Voltage
Input Clamp Voltage
Input Current at Maximum
Input Voltage
High Level Input Current
Low Level Input Current
Short-circuit Output Current
Output High Fan-out
Output Low Fan-out
IOH
IOL
VIH
VIL
VIK
IIHH
Doc #97020
2/5/97
IIH
IIL
IOS
MIN
2.5
TYP
3.4
MAX
UNITS
V
0.35
0.5
V
-1.0
20.0
0.8
-1.2
0.1
mA
mA
V
V
V
mA
20
-0.6
-150
25
12.5
µA
mA
mA
Unit
Load
2.0
-60
NOTES
VCC = MIN, IOH = MAX
VIH = MIN, VIL = MAX
VCC = MIN, IOL = MAX
VIH = MIN, VIL = MAX
VCC = MIN, II = IIK
VCC = MAX, VI = 7.0V
VCC = MAX, VI = 2.7V
VCC = MAX, VI = 0.5V
VCC = MAX
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
2
DDU66F
PACKAGE DIMENSIONS
14
12
10
8
Lead Material:
Nickel-Iron alloy 42
TIN PLATE
14
12
10
.410
TYP.
1
1
4
6
8
4
6
7
7
.280
MAX.
.780 MAX.
.820 MAX.
.290
MAX.
.020 .320
TYP. MAX.
.130
±.030
.015 TYP.
.010±.002
.018
TYP.
.070 MAX.
.350
MAX.
.600±.010
.018 TYP.
.600 TYP.
14
.040
TYP.
12
10
.010 TYP.
4
8
.090
6
.040
TYP.
.020 TYP.
14
.270
TYP.
1
12
7
.050
TYP.
DDU66F-xxA2 (Commercial Gull-Wing)
.320
TYP.
.270
TYP.
1
.300
MAX.
.050 TYP.
8
10
.430
TYP.
.100
.600
.790 MAX.
.300
TYP.
DDU66F-xxME7 (Military)
DDU66F-xx (Commercial)
.020 TYP.
.020 TYP.
.100
TYP.
4
.110
6
7
.100
.600
.790 MAX.
.350
MAX.
.110
TYP.
DDU66F-xxB2 (Commercial J-Lead)
.650
.100
.100
1
.017
14
1
.510
MAX.
.300
TYP.
14
.510
MAX.
.300
TYP.
7
7
8
.100
.300
.510 MAX.
.050
.510 MAX.
.080
.300
.200 MAX. (Com)
.025
8
.100
.050
.008
.017
.200 MAX. (Com)
.225 MAX. (Mil)
.080
.008
.225 MAX. (Mil)
.065
TYP.
.360
TYP.
.065
TYP.
.045
DDU66F-xxD1 (Commercial SMD)
DDU66F-xxMD1 (Military SMD)
Doc #97020
2/5/97
.005
.360 TYP.
.065 TYP.
.065 TYP.
DDU66F-xxD4 (Commercial SMD)
DDU66F-xxMD4 (Military SMD)
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
3
DDU66F
DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT:
o
o
Ambient Temperature: 25 C ± 3 C
Supply Voltage (Vcc): 5.0V ± 0.1V
Input Pulse:
High = 3.0V ± 0.1V
Low = 0.0V ± 0.1V
Source Impedance:
50Ω Max.
Rise/Fall Time:
3.0 ns Max. (measured
between 0.6V and 2.4V )
Pulse Width:
PWIN = 1.5 x Total Delay
Period:
PERIN = 10 x Total Delay
OUTPUT:
Load:
Cload:
Threshold:
1 FAST-TTL Gate
5pf ± 10%
1.5V (Rising & Falling)
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
PRINTER
COMPUTER
SYSTEM
REF
PULSE
GENERATOR
OUT
IN
TRIG
DEVICE UNDER
TEST (DUT)
T1
IN
T2
TRIG
TIME INTERVAL
COUNTER
T3
T4
T5
Test Setup
PERIN
PWIN
TRISE
INPUT
SIGNAL
TFALL
VIH
2.4V
1.5V
0.6V
2.4V
1.5V
0.6V
TRISE
VIL
TFALL
VOH
OUTPUT
SIGNAL
1.5V
1.5V
VOL
Timing Diagram For Testing
Doc #97020
2/5/97
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
4
Similar pages