Maxim DG202 Quad spst cmos analog switch Datasheet

19-3960; Rev 3; 6/06
Quad SPST CMOS Analog Switches
The DG202/DG212 are normally open, quad singlepole single-throw (SPST) analog switches. These
CMOS switches can be continuously operated with
power supplies ranging from ±4.5V to ±18V. Maxim
guarantees that these switches will not latch up if the
power supplies are disconnected with input signals still
connected.
The DG202/DG212 are similar to the DG201/DG211
except for inverted control inputs. All devices have
guaranteed break-before-make switching, as well as
essentially constant on-resistance over the analog
signal range. All switches conduct current in either
direction and add no offset to the output signal.
Compared to the original manufacturer’s products,
Maxim’s DG202/DG212 consume very little power,
making them better suited for portable applications.
Maxim has also eliminated the need for the third logic
power supply (VL) that is required for the operation of
the original manufacturer’s DG212 without sacrificing
compatibility.
Features
♦ Guaranteed ±4.5V to ±18V Operation
♦ No VL Supply Required
♦ Nonlatching with Supplies Turned Off and Input
Signals Present
♦ CMOS and TTL Logic Compatible
♦ Monolithic, Low-Power CMOS Design
Ordering Information
TEMP RANGE
PIN-PACKAGE
DG202CUE
PART
0°C to +70°C
16 TSSOP
DG202CSE
0°C to +70°C
16 SO
DG202CJ
0°C to +70°C
16 Plastic DIP
DG202C/D
0°C to +70°C
Dice
DG202AEGE
-40°C to +85°C
16 QFN (5mm x 5mm)
DG202AEUE
-40°C to +85°C
16 TSSOP
DG202ADY
-40°C to +85°C
16 SO
DG202ADJ
-40°C to +85°C
16 Plastic DIP
DG202AK
DG212CUE
-55°C to +125°C
0°C to +70°C
16 CERDIP
16 TSSOP
DG212CSE
0°C to +70°C
16 SO
DG212CJ
0°C to +70°C
16 Plastic DIP
DG212C/D
0°C to +70°C
Dice
DG212EGE
Sample/Holds
-40°C to +85°C
DG212EUE
Automatic Test Equipment
DG212DY
-40°C to +85°C
-40°C to +85°C
PBX, PABX
DG212DJ
-40°C to +85°C
16 Plastic DIP
DG212ETE
-40°C to +85°C
16 Thin QFN
Applications
Analog Multiplexers
Programmable Gain Amplifiers
Communications Systems
Typical Operating Circuit
VIN x 10V
Pin Configurations
1
16 IN2
D1
2
15 D2
S1
3
14 S2
V-
4
GND
5
12
S4
6
11 S3
6
11
D4
7
10 D3
7
10
IN4
8
16 *
* 1
2
15
3
14
-15V 4
5
10kΩ
16 SO
IN1
5kΩ
5kΩ
16 QFN (5mm x 5mm)
16 TSSOP
DG202
DG212
* 8
13 +15V
9 *
PROGRAMMABLE GAIN AMPLIFIER
NOTE: *PINS 1, 8, 9, AND 16 ARE LOGIC CONTROL INPUTS
40kΩ
VOUT
13 V+
DG202
DG212
12 V L
9
IN3
20kΩ
DIP/SO
LOGIC
SWITCH
0
1
OFF
ON
SWITCHES SHOWN FOR LOGIC “0” INPUT
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
DG202/DG212
General Description
DG202/DG212
Quad SPST CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS (DG212)
V+ to V-………………………………….............……………….44V
VIN to Ground…………………………..................…. ……...V-, V+
VL to Ground………....................……………………….-0.3V, 25V
VS or VD to V+……...........................………………………0, -40V
VS or VD to V-……………........................…………………..0, 40V
V+ to Ground…………………...................................………...25V
V- to Ground…………………………………….................…...-25V
Current, Any Terminal Except S or D……….............……...30mA
Continuous Current, S or D……………………..............…...20mA
Peak Current, S or D
(pulsed at 1ms 10% duty cycle max)…..........................70mA
Storage Temperature Range……………..……..-65°C to +125°C
Operating Temperature Range
DG212C ................................……………...……...0°C to +70°C
DG212D/E .........................……………...……...-40°C to +85°C
Power Dissipation (TA = +70°C) (Note 1)
16-Pin Plastic Dip (derate 10.5mW/°C above +70°C) ..842mW
16-Pin Narrow SO (derate 8.7mW/°C above+70°C). ....696mW
16-Pin TSSOP (derate 9.4mW/°C above +70°C) ..........755mW
16-Pin QFN (5mm x 5mm)
(derate 19.2mW/°C above +70°C) .........................1538mW
16-Pin Thin QFN
(derate 14.7mW/°C above +70°C) .........................1177mW
Note 1: Device mounted with all leads soldered to PC board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS (DG212)
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 2.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SWITCH
Analog Signal Range
VANALOG
Drain-Source ON-Resistance
RDS (ON)
-15
Source OFF-Leakage Current
IS (OFF)
VIN = 0.8V
Drain OFF-Leakage Current
ID (OFF)
VIN = 0.8V
Drain ON-Leakage Current
(Note 3)
ID (ON)
VD = ±10V, VIN = 2.4V, IS = 1mA
VS = 14V, VD = -14V
VS = -14V, VD = 14V
-5.0
VS = 14V, VD = -14V
VS = -14V, VD = 14V
+15
V
115
175
Ω
0.01
5.0
-0.02
0.01
-5.0
-0.02
VS = VD = -14V, VIN = 2.4V
-5.0
-0.15
VIN = 2.4V
-1.0
-0.0004
VS = VD = 14V, VIN = 2.4V
0.1
5.0
nA
5.0
INPUT
Input Current with Input Voltage
High
IINH
Input Current with Input Voltage
Low
IINL
VIN = 15V
VIN = 0
0.003
-1.0
1.0
µA
-0.0004
DYNAMIC
Turn-ON Time
Turn-OFF Time
tON
tOFF1
tOFF2
See Switching Time Test Circuit
VS = 2V, RL = 1kΩ, CL = 35pF
460
1000
360
500
Source OFF-Capacitance
CS (OFF)
VS = 0, VIN = 0, f = 1MHz
Drain OFF-Capacitance
CD (OFF)
VD = 0, VIN = 0, f = 1MHz
5
VD = VS = 0, VIN = 5V, f = 1MHz
16
Channel ON-Capacitance
OFF-Isolation (Note 4)
Crosstalk
(Channel to Channel)
2
CD + S (ON)
OIRR
CCRR
ns
450
5
pF
70
VIN = 0, RL = 1kΩ, CL = 15pF,
VS = 1VRMS, f = 100kHz
90
_______________________________________________________________________________________
dB
Quad SPST CMOS Analog Switches
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 2.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
0.02
0.4
0.01
0.4
0
0
UNITS
SUPPLY
Positive Supply Current
I+
Negative Supply Current
I-
Logic Supply Current
IL
Power-Supply Range
for Continous Operation
VIN = 0 and 2.4V (all)
±4.5
VOP
±18.0
mA
V
Note 2: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
Note 3: ID(ON) is leakage from driver into “ON” switch.
Note 4: OFF-Isolation = 20 log VS/VD, VS = input to OFF switch, VD = output.
ABSOLUTE MAXIMUM RATINGS (DG202)
Voltages Reference to VV+………………………………………………..……………..44V
GND……………………………………………..……….…….25V
Digital Inputs (Note 1), VS, VD ............................-2V to (V+ + 2V)
or 20mA, whichever occurs first
Current, Any Terminal Except S or D………..….…………...30mA
Continuous Current, S or D…………………………………...20mA
Peak Current, S or D
(pulsed at 1ms 10% duty cycle max)…………………….70mA
Operating Temperature Range
DG202C ....................…………........………..…...0°C to +70°C
DG202D/E............………………….....…..….…-40°C to +85°C
DG202A ..........………........................…….…-55°C to +125°C
Storage Temperature Range………………..…..-65°C to +150°C
Power Dissipation (Note 2)
16-Pin Plastic Dip (derate 10.5mW/°C above +70°C) ...842mW
16-Pin SO (derate 8.7mW/°C above +70°C) .................696mW
16-Pin TSSOP (derate 9.4mW/°C above +70°C) ...........755mW
16-Pin QFN (5 ✕ 5)
(derate 19.2mW/°C above +70°C)...........................1538mW
16-Pin CERDIP (derate 10.0mW/°C above +70°C)......800mW
Note 1: Signals on S_, D_, or IN_ exceeding V+ or V- on Maxim’s DG202 will be clamped by internal diodes, and are also internally current limited to 25mA.
Note 2: Device mounted with all leads soldered to PC board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS (DG202)
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 3.)
PARAMETER
SYMBOL
CONDITIONS
DG202A
MIN
DG202C, D, E
TYP
MAX
MIN
15
-15
115
175
0.01
1.0
UNITS
TYP
MAX
15
V
115
200
Ω
0.01
5.0
SWITCH
Analog Signal Range
VANALOG
Drain-Source ON Resistance
RDS (ON)
-15
Source OFF-Leakage Current
IS (OFF)
VIN = 0.8V
Drain OFF-Leakage Current
ID (OFF)
VIN = 0.8V
Drain ON-Leakage Current
(Note 4)
ID (ON)
VIN = 2.4V
VD = ±10V, VIN = 2.4V, IS = 1mA
VS = 14V, VD = -14V
VS = -14V, VD = 14V
-1.0
VS = 14V, VD = -14V
VS = -14V, VD = 14V
0.01
-1.0
VS = -14V
VS = 14V
-0.02
1.0
-0.02
0.1
-1.0
-1.0
-0.02
0.01
-1.0
1.0
5.0
-0.02
0.1
nA
1.0
-5.0
_______________________________________________________________________________________
3
DG202/DG212
ELECTRICAL CHARACTERISTICS (DG212) (continued)
DG202/DG212
Quad SPST CMOS Analog Switches
ELECTRICAL CHARACTERISTICS (DG202) (continued)
(V+ = +15V, V- = -15V, GND = 0, TA = +25°C, unless otherwise noted.) (For more information on TYP values see Note 3.)
PARAMETER
SYMBOL
CONDITIONS
DG202A
MIN
TYP
DG202C, D, E
MAX
MIN
TYP
MAX
-1.0
-0.0004
UNITS
INPUT
Input Current with Input
Voltage High
IINH
Input Current with Input
Voltage Low
IINL
VIN = 2.4V
-1.0 -0.0004
VIN = 15V
0.003
VIN = 0
1.0
-1.0 -0.0004
0.003
-1.0
1.0
µA
-0.0004
DYNAMIC
Turn-ON Time
tON
Turn-OFF Time
tOFF1
Charge Injection
Q
See Figure 1 Switching Time
Test Circuit
CL = 1000pF, VGEN = 0,
RGEN = 0
Source OFF-Capacitance
CS (OFF)
Drain OFF-Capacitance
CD (OFF)
Channel ON-Capacitance
CD (ON) VD = VS = 0,
+ CS (ON) VIN = 5V
480
600
480
600
370
450
370
450
20
VS = 0,
VIN = 0
20
5
5
5
5
ns
pC
f = 140kHz
pF
16
16
OFF-Isolation
VIN = 0, ZL = 75Ω
70
70
Crosstalk
(Channel to Channel)
VS = 2.0V, f = 100kHz
90
90
dB
SUPPLY
Positive Supply Current
I+
All channels ON or OFF
Negative Supply Current
I-
All channels ON or OFF
Power-Supply Range for
Continuous Operation
VOP
0.02
-0.1
±4.5
0.1
-0.01
0.02
-0.1
±18
±4.5
Note 3: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
Note 4: ID (ON) is leakage from driver into “ON” switch.
4
_______________________________________________________________________________________
0.1
-0.01
±18.0
mA
V
Quad SPST CMOS Analog Switches
(V+ = +15V, V- = -15V, GND = 0, TA = full opearting temperature range, unless otherwise noted.) (For more information on TYP
values see Note 3.)
PARAMETER
SYMBOL
DG202A
CONDITIONS
MIN
TYP
DG202C, D, E
MAX
MIN
+15
-15
TYP
MAX
UNITS
SWITCH
Analog Signal Range
VANALOG
-15
Drain-Source ON Resistance
(Note 5)
RDS (ON)
Source OFF-Leakage Current
IS (OFF)
VIN = 0.8V
Drain OFF-Leakage Current
ID (OFF)
VIN = 0.8V
Drain ON-Leakage Current
(Note 6)
ID (ON)
VIN = 2.4V
VD = ±10V, VIN = 2.4V, IS = 1mA
250
VS = 14V, VD = -14V
VS = -14V, VD = 14V
100
-100
250
Ω
100
100
-100
100
-100
VS = -14V
200
VD = 14V
V
-100
VS = 14V, VD = -14V
VS = -14V, VD = 14V
+15
nA
200
-200
-200
-1.0
-1.0
INPUT
Input Current with Input
Voltage High
VIN = 2.4V
IINH
Input Current with Input
Voltage Low
VIN = 15V
1.0
VIN = 0
IINL
-1.0
1.0
µA
-1.0
Note 5: Electrical characteristics, such as On-Resistance, will change when power supplies other than ±15V, are used.
Note 6: ID (ON) is leakage from driver into “ON” switch.
Pin Description
PIN
DIP/SO/TSSOP
QFN/TQFN
NAME
FUNCTION
1, 16, 9, 8
15, 14, 7, 6
IN1–IN4
Input
2, 15, 10, 7
16, 13, 8, 5
D1–D4
Analog Switch Drain Terminal
3, 14, 11, 6
1, 12, 9, 4
S1–S4
Analog Switch Source Terminal
4
2
V-
Negative-Supply Voltage Input
5
3
GND
12
10
N.C.
13
11
V+
Positive-Supply Voltage Input—Connected to Substrate
—
EP
EP
Exposed Pad. Connect exposed pad to V+ or leave EP unconnected.
Ground
No Connection
Switching Time Test Circuit
Switch output waveform shown for VS = constant with
logic input waveform as shown. Note that VS may be
+ve or -ve as per switching times test circuit. VO is the
steady state output with switch on. Feedthrough via
gate capacitance may result in spikes at leading and
trailing edge of output waveform.
Protecting Against Fault
Conditions
Fault conditions occur when power supplies are turned
off when input signals are still present, or when overvoltages occur at the inputs during normal operation. In
either case, source-to-body diodes can be forward
biased and conduct current from the signal source. If
_______________________________________________________________________________________
5
DG202/DG212
ELECTRICAL CHARACTERISTICS (DG202)
DG202/DG212
Quad SPST CMOS Analog Switches
t r < 20ns
t f < 20ns
LOGIC 1 SW ON
+15V
3V
SWITCH
INPUT
50%
V+
0
VS = +2V
SWITCH
INPUT
RL
RL + rDS(ON)
VO = VS
LOGIC
INPUT
VS
SWITCH
OUTPUT
VO
0.9
VO
0.9
VO
tOFF1
0
tOFF
LOGIC
INPUT
S1
SWITCH
OUTPUT
VO
D1
IN1
CL
35pF
RL
1kΩ
0.1
GND
tOFF2
V-
(REPEAT TEST FOR IN2, IN3, AND IN4)
-15V
0V
Figure 1. Switching Time
Typical RDS(ON) vs. Power Supplies for Maxim’s DG202, and DG212
RDS(ON) AT ANALOG SIGNAL LEVEL
POWER SUPPLIES
-5V
+5V
-10V
+10V
-15V
±5V
350Ω
380Ω
—
—
—
—
±10V
—
—
165Ω
250Ω
—
—
±15V
—
—
125Ω
160Ω
135Ω
155Ω
this current is required to be kept to low (µA) levels
then the addition of external protection diodes is recommended.
To provide protection for overvoltages up to 20V above
the supplies, a 1N4001 or 1N914 type diode should be
placed in series with the positive and negative supplies
as shown in Figure 2. The addition of these diodes will
reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.
IN4001
-15V
1
16
2
15
14
3
4
5
DG202
DG212
13
12
6
11
7
10
8
9
Pin Configurations (continued)
TOP VIEW
S1
1
V-
2
GND
3
D1
IN1
IN2
D2
16
15
14
13
DG202
DG212
Figure 2. Protection against Fault Conditions
12
S2
11
V+
10
N.C.
9
S3
*EP
S4
4
5
6
7
8
D4
IN4
IN3
D3
TQFN*
*EXPOSED PAD. CONNECT EXPOSED PAD TO V+
OR LEAVE EXPOSED PAD UNCONNECTED.
6
+15V
_______________________________________________________________________________________
IN4001
+15V
Quad SPST CMOS Analog Switches
N
E
H
INCHES
MILLIMETERS
MAX
MIN
0.069
0.053
0.010
0.004
0.014
0.019
0.007
0.010
0.050 BSC
0.150
0.157
0.228
0.244
0.016
0.050
MAX
MIN
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
1.27 BSC
3.80
4.00
5.80
6.20
0.40
SOICN .EPS
DIM
A
A1
B
C
e
E
H
L
1.27
VARIATIONS:
1
INCHES
TOP VIEW
DIM
D
D
D
MIN
0.189
0.337
0.386
MAX
0.197
0.344
0.394
MILLIMETERS
MIN
4.80
8.55
9.80
MAX
5.00
8.75
10.00
N MS012
8
AA
14
AB
16
AC
D
A
B
e
C
0∞-8∞
A1
L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL
DOCUMENT CONTROL NO.
21-0041
REV.
B
1
1
_______________________________________________________________________________________
7
DG202/DG212
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PDIPN.EPS
DG202/DG212
Quad SPST CMOS Analog Switches
8
_______________________________________________________________________________________
Quad SPST CMOS Analog Switches
CDIPS.EPS
_______________________________________________________________________________________
9
DG202/DG212
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
DG202/DG212
Quad SPST CMOS Analog Switches
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
10
______________________________________________________________________________________
G
1
1
Quad SPST CMOS Analog Switches
32L QFN.EPS
______________________________________________________________________________________
11
DG202/DG212
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
DG202/DG212
Quad SPST CMOS Analog Switches
Revision History
Pages changed at Rev3: 1–6, 11
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
Similar pages