Murata DLW31SN601SQ2 Smd/block type emi suppression filter Datasheet

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
p/PLp
Chip Ferrite Bead
DL
150
Part Numbering
152
Series Line Up
154
Product Detail
156
!Caution/Notice
174
Soldering and Mounting
176
Packaging
182
Design Kits
184
Block Type EMIFILr
Chip Common Mode Choke Coil
Series Introduction
Chip EMIFILr
Chip Common Mode Choke Coil
Large Current Common Mode Choke Coil for Automotive Available
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
Chip Ferrite Bead
DLp
Series Introduction
Common Mode Current
Magnetic flux by common mode current is
added each other and works as an inductor
Differential Mode Current
Chip EMIFILr
Magnetic flux by differential mode current is
canceled each other and do not works as an
inductor
Features,
Classification
Category
Ultra high cut-off
frequency
for high speed
differential signal lines
Structure
Film type
Block Type EMIFILr
Chip Common Mode Choke Coil
Wound type
High cut-off frequency
High Coupling
For high speed
differential signal lines
(
)
High cut-off frequency
for high speed
differential signal lines
Film type
Wound type
for general differential
signal lines
Film type
Part Number
Comments
DLP11SA
· Low profile, small size, suitable for mobile
equipments.
· Tight terminal pitch enables high density layout.
· Ultra high cut-off frequency and its matching to line
impedance enables good transmission of high
speed signal.
DLW21SN_HQ2
· Ultra high self resonance frequency enables high
cut-off frequency.
· Its matching to line impedance enables good
transmission of high speed signal.
DLP0NS
DLP11SN
DLP2AD
· Low profile, small size, suitable for mobile
equipments.
· Tight terminal pitch enables high density layout.
· High cut-off frequency enables good transmission
of high speed signal.
DLW21SN_SQ2
DLW31S
DLW21H
· Ultra high self resonance frequency enables high
cut-off frequency.
· DLW21H is designed as low profile.
DLP31S
DLP31D
· Low profile,small size, suitable for mobile
equipments.
· Tight terminal pitch enables high density layout.
DLW5AH
Large current
High coupling
(For power lines)
Wound type
DLW5BS
· Large current (6A max.), suitable for input
connector from an AC adaptor.
· DLW5BT is designed as low profile.
DLW5BT
Relative high differential
mode impedance
Low coupling
(For audio lines)
Large current
Automotive Available
(For power lines)
Multilayer
type
Available up to 10A
Winding type
Cased structure
DLM11G
DLM2HG
PLT10HH
· Modified its differential mode impedance higher
than other common mode choke coils, this feature
makes possible to suppress both common mode
and differential mode noise.
· DLM11GN601SD2 is ideal to keep low distortion
audio signal.
· DLM2HG can meet stereo 3 lines which contain a
ground line.
· Large current, high reliability, suitable for mortors in
automobile.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
150
Noise
Suppression DLP/DLW Series
Example
Chip Ferrite Bead
Mechanism of Skew Improvement
Skew Improve Effect of Common Mode Choke Coil
Waveform rises (or falls)
Example of Skew Improvement by Common Mode Choke Coil
(Test using pulse generator waveform)
Waveform is equivalent to 1000Mbps signal
Current change generates
magnetic flux on a ferrite core
Waveform with intentionally made skew (skew: 100ps)
Skew is improved by common mode choke coil
Electromotive force is
generated on another line
Chip EMIFILr
This electromotive force works to
decrease the delay of waveform
Noise Suppression of Common Mode Choke Coil in HDMI Line
60
60
55
55
50
45
40
35
30
Without filter
DLW21SN900HQ2
25
20
1000
1500
2000
2500
3000
3500
4000
4500
50
45
40
35
30
Without filter
DLP11SA900HL2
25
20
1000
5000
1500
2000
Frequency (MHz)
Test Example of HDMI1.3
Waveform Transmission
Chip Common Mode Choke Coil
Noise Level (dBµV/m)
Noise Level (dBµV/m)
Device under test / Transmitter : game machine Receiver : projector
Cable / HDMI categoly2 3m cable
Test resolution / 1080p Deep color 12bit (Data 1.11GHz) DVD play mode
2500
3000
3500
4000
4500
5000
Frequency (MHz)
ESD protection device only
Film Type DLP11SN900HL2
(Cut-off frequency is most low in the table below)
~Using ESD protection device 0.05pF~
Block Type EMIFILr
Signal frequency : 1.11GHz (Deep color 12bit)
Specification
satisfied
Video signal generator
CLOCK
Wound Type
DLW21SN900HQ2
Film Type
DLP11SA900HL2
Film Type Array
DLP2ADN900HL4
Over 10GHz
Around 6GHz
Around 4GHz
Specification satisfied
Specification satisfied
Specification satisfied
Rise time: 83.4ps
Fall time: 77.4ps
Rise time: 90.4ps
Fall time: 85.5ps
Rise time: 100ps
Fall time: 97.4ps
DATA
common mode choke coil ESD protection device 0.05pF
Cut-off Frequency
Judge
Transition Time
Each of common mode choke coil can keep waveform, satisfy the specification.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
151
Chip Ferrite Bead
DL p
(Part Number)
Chip Common Mode Choke Coil
DL
W
21 S
N
q
w
e r t
371 S
Q
2
Part Numbering
L
u i o !0
y
qProduct ID
tCategory
Product ID
Code
DL
Chip Common Mode Choke Coils
Category
A
B
Chip EMIFILr
wStructure
C
Code
Structure
N
W
Wire Wound Type
R
M
Multilayer Type
P
Film Type
eDimensions (LgW)
Code
Dimensions (LgW)
EIA
0N
0.85g0.65mm
03025
Expressed by a letter.
yImpedance
Typical impedance at 100MHz is expressed by three figures. The
unit is in ohm (Ω). The first and second figures are significant
digits, and the third figure expresses the number of zeros which
follow the two figures.
uCircuit
11
1.25g1.0mm
0504
1N
1.5g0.65mm
05025
Code
21
2.0g1.2mm
0805
S
31
3.2g1.6mm
1206
M
2A
2.0g1.0mm
0804
H
2H
2.5g2.0mm
1008
U
5A
5.0g3.6mm
2014
5B
5.0g5.0mm
2020
Circuit
Expressed by a letter.
iFeatures (2)
Chip Common Mode Choke Coil
Code
rFeatures (1)
Features
D
Code
Type
L
S
Magnetically Shielded One Circuit Type
Q
D
Magnetically Shielded Two Circuit Type
Z
H
Open Magnetic One Circuit Type
G
Magnetically Monolithic Type (sectional winding)
T
Magnetically Shielded One Circuit Low Profile Type
Expressed by a letter.
oNumber of Signal Lines
Code
Number of Signal Lines
2
Two Lines
3
Three Lines
4
Four Lines
Block Type EMIFILr
!0Packaging
Code
Packaging
K
Embossed Taping (ø330mm Reel)
DLW5AH/DLW5BS/DLW5BT
Series
L
Embossed Taping (ø180mm Reel)
All Series
B
Bulk
All Series
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
152
Part Numbering
T 10H H 102 6R0 P N B
PL
q w
e
r
t
y
u i o
qProduct ID
Product ID
PL
Common Mode Choke Coils
Code
Type
T
DC Type
wType
eApplications
Code
Applications
10H
for DC Line High-frequency Type
rFeatures
Code
Features
H
for Automotive
tImpedance
Expressed by three figures. The unit is ohm (Ω). The first and
second figures are significant digits, and the third figure
expresses the number of zeros which follow the two figures.
yRated Current
Expressed by three figures. The unit is ampere (A). The first and
second figures are significant digits, and the third figure
expresses the number of zeros which follow the two figures.
A decimal point is expressed by the capital letter "R". In this case,
all figures are significant digits.
Chip EMIFILr
(Part Number)
Common Mode Choke Coils
Chip Ferrite Bead
PL p
uWinding Mode
Code
Winding Mode
P
Aligned Winding Type
iLead Dimensions
Code
Lead Dimensions
N
No Lead Terminal (SMD)
oPackaging
Bulk
PLT10H
Series
L
Embossed Taping (ø178mm/ø180mm Reel)
PLT10H
K
Embossed Taping (ø330mm Reel)
PLT10H
Chip Common Mode Choke Coil
Packaging
B
Block Type EMIFILr
Code
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
153
DL p
Chip Common Mode Choke Coil
Type
Chip Ferrite Bead
Multilayer Type
for Audio Lines
Size Code Thickness
(Inch)
(mm)
0504
1008
p158
p159
p160
03025
p162
Chip EMIFILr
Film Type
for Differential
Signal Lines
0504
p163
p164
1206
p165
05025
p166
Chip Common Mode Choke Coil
Film Array Type
for Differential
Signal Lines
0804
p168
1206
p169
Block Type EMIFILr
0805
Wire Wound Type
for Differential
Signal Lines
p171
p172
1206
0.5
1.2
0.45
0.45
0.45
0.45
0.45
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.3
1.15
1.15
1.15
0.45
0.45
0.45
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
0.82
1.15
1.15
1.15
1.15
1.15
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
0.9
0.9
0.9
0.9
1.9
1.9
1.9
1.9
1.9
1.9
Part Number
DLM11GN601SD2
DLM2HGN601SZ3
DLP0NSN670HL2
DLP0NSN900HL2
DLP0NSN121HL2
DLP0NSA150HL2
DLP0NSC280HL2
DLP11SN670SL2
DLP11SN121SL2
DLP11SN161SL2
DLP11SN900HL2
DLP11SN201HL2
DLP11SN241HL2
DLP11SN281HL2
DLP11SN331HL2
DLP11SA350HL2
DLP11SA670HL2
DLP11SA900HL2
DLP11TB800UL2
DLP31SN121ML2
DLP31SN221ML2
DLP31SN551ML2
DLP1NDN350HL4
DLP1NDN670HL4
DLP1NDN900HL4
DLP2ADA350HL4
DLP2ADA670HL4
DLP2ADA900HL4
DLP2ADN670HL4
DLP2ADN900HL4
DLP2ADN121HL4
DLP2ADN161HL4
DLP2ADN201HL4
DLP2ADN241HL4
DLP2ADN281HL4
DLP31DN900ML4
DLP31DN131ML4
DLP31DN201ML4
DLP31DN321ML4
DLP31DN441ML4
DLW21SN670SQ2
DLW21SN900SQ2
DLW21SN121SQ2
DLW21SN181SQ2
DLW21SN261SQ2
DLW21SN371SQ2
DLW21SN670HQ2
DLW21SN900HQ2
DLW21SN121HQ2
DLW21SR670HQ2
DLW21HN670SQ2
DLW21HN900SQ2
DLW21HN121SQ2
DLW21HN181SQ2
DLW31SN900SQ2
DLW31SN161SQ2
DLW31SN261SQ2
DLW31SN601SQ2
DLW31SN102SQ2
DLW31SN222SQ2
Series Line Up
Common Mode Impedance
Rated Current
(at 100MHz/20°C)
600ohm±25%
600ohm±25%
67ohm±20%
90ohm±20%
120ohm±20%
15ohm±5ohm
28ohm±20%
67ohm±20%
120ohm±20%
160ohm±20%
90ohm±20%
200ohm±20%
240ohm±20%
280ohm±20%
330ohm±20%
35ohm±20%
67ohm±20%
90ohm±20%
80ohm±25%
120ohm±20%
220ohm±20%
550ohm±20%
35ohm±20%
67ohm±20%
90ohm±20%
35ohm±20%
67ohm±20%
90ohm±20%
67ohm±20%
90ohm±20%
120ohm±20%
160ohm±20%
200ohm±20%
240ohm±20%
280ohm±20%
90ohm±20%
130ohm±20%
200ohm±20%
320ohm±20%
440ohm±20%
67ohm±25%
90ohm±25%
120ohm±25%
180ohm±25%
260ohm±25%
370ohm±25%
67ohm±25%
90ohm±25%
120ohm±25%
67ohm±25%
67ohm±25%
90ohm±25%
120ohm±25%
180ohm±25%
90ohm±25%
160ohm±25%
260ohm±25%
600ohm±25%
1000ohm±25%
2200ohm±25%
100mA
100mA
110mA
100mA
90mA
100mA
100mA
180mA
140mA
120mA
150mA
110mA
100mA
90mA
80mA
170mA
150mA
150mA
100mA
100mA
100mA
100mA
100mA
80mA
60mA
150mA
130mA
120mA
140mA
130mA
120mA
100mA
90mA
80mA
80mA
160mA
120mA
100mA
80mA
70mA
400mA
330mA
370mA
330mA
300mA
280mA
320mA
280mA
280mA
400mA
330mA
330mA
280mA
250mA
370mA
340mA
310mA
260mA
230mA
200mA
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
154
DLp Chip Common Mode Choke Coil Series Line Up
p156
p156
Wire Wound Type
for Power Lines
and Signal Lines
PL p
2020p157
4.3
4.5
4.5
4.5
4.5
4.5
2.5
2.5
2.5
2.5
2.5
DLW5AHN402SQ2
DLW5BSN191SQ2
DLW5BSN351SQ2
DLW5BSN102SQ2
DLW5BSN152SQ2
DLW5BSN302SQ2
DLW5BTN101SQ2
DLW5BTN251SQ2
DLW5BTN501SQ2
DLW5BTN102SQ2
DLW5BTN142SQ2
Common Mode Impedance
Rated Current
(at 100MHz/20°C)
4000ohm(Typ.)
190ohm(Typ.)
350ohm(Typ.)
1000ohm(Typ.)
1500ohm(Typ.)
3000ohm(Typ.)
100ohm(Typ.)
250ohm(Typ.)
500ohm(Typ.)
1000ohm(Typ.)
1400ohm(Typ.)
200mA
5000mA
2000mA
1500mA
1000mA
500mA
6000mA
5000mA
4000mA
2000mA
1500mA
Large Current Common Mode Choke Coil for Automotive Available
Type
Size
p173
12.9x6.6
(mm)
Part Number
9.4
9.4
9.4
9.4
PLT10HH401100PN
PLT10HH501100PN
PLT10HH9016R0PN
PLT10HH1026R0PN
Series Line Up
Common Mode Impedance
Rated Current
(at 10MHz/20°C)
400ohm
500ohm
900ohm
1000ohm
10A
10A
6A
6A
Block Type EMIFILr
Chip Common Mode Choke Coil
Large Current
Common Mode Choke Coil
for Automotive Available
Thickness
(mm)
Chip Ferrite Bead
2014
Part Number
Chip EMIFILr
Size Code Thickness
(Inch)
(mm)
Type
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
155
DLW Series
Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil
DLW5AH/DLW5BS
DLW5AH/DLW5BS
Series (2014/2020 Size)
■ Equivalent Circuit
0.45 min.
■ Dimensions
DLW5AH
*
*
0.5 min.
(W) 3.6±0.3
(1)
No polarity.
1.7 1.3 1.7
±0.3 ±0.3 ±0.3
Chip EMIFILr
■ Packaging
position of wiring should
* Starting
be covered with resin.
: Electrode
(3)
1.3 0.9 1.3
±0.3 ±0.3 ±0.3
(in mm)
■ Dimensions
DLW5BS
(3)
(4)
(L) 5.0±0.3
(2)
(4)
(2)
(1)
(T) 4.3 max.
Chip Ferrite Bead
5A max, common mode choke coil for power lines.
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
400
K
330mm Reel Embossed Tape
1500
B
Bulk(Bag)
100
■ Equivalent Circuit
Polarity Marking
* The marking to
indicate the product
direction can be
applicable.
(Optional)
(2)
(1)
(3)
(4)
1.7±0.3
Chip Common Mode Choke Coil
Universal Type [Power Lines/Signal Lines]
(4)
■ Packaging
(T) 4.5 max.
0.5 min.
(L) 5.0±0.3
1.3±0.3
1.7±0.3
3.6±0.3
(W) 5.0±0.3
(1)
(2)
0.45 min.
No polarity.
: Electrode
(3) 1.3±0.3
0.9±0.3
(in mm)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
400
K
330mm Reel Embossed Tape
1500
B
Bulk(Bag)
100
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW5AHN402SQ2p
4000ohm(Typ.)
200mA
50Vdc
10M ohm
125Vdc
3.0ohm max.
DLW5BSN191SQ2p
190ohm(Typ.)
5000mA
50Vdc
10M ohm
125Vdc
0.02ohm max.
DLW5BSN351SQ2p
350ohm(Typ.)
2000mA
50Vdc
10M ohm
125Vdc
0.04ohm max.
DLW5BSN102SQ2p
1000ohm(Typ.)
1500mA
50Vdc
10M ohm
125Vdc
0.06ohm max.
DLW5BSN152SQ2p
1500ohm(Typ.)
1000mA
50Vdc
10M ohm
125Vdc
0.1ohm max.
DLW5BSN302SQ2p
3000ohm(Typ.)
500mA
50Vdc
10M ohm
125Vdc
0.3ohm max.
Rated Current Rated Voltage
Withstand Voltage DC Resistance
■ Impedance-Frequency Characteristics (Main Items)
100000
■ Derating of Rated Current
DLW5BSN191
DLW5BSN191SQ2 Temperature Derating
10000
5
DLW5AHN402SQ2
DLW5BSN302SQ2
DLW5BSN152SQ2
DLW5BSN102SQ2
DLW5BSN351SQ2
DLW5BSN191SQ2
1000
Rated Current (A)
Impedance (Ω)
Block Type EMIFILr
Operating Temperature Range: -25°C to +85°C (DLW5AH), -40°C to +85°C (DLW5BS) Number of Circuit: 1
Common mode
100
DLW5AHN402SQ2
DLW5BSN302SQ2
DLW5BSN152SQ2
Differential mode
4.75
4.5
DLW5BSN102SQ2
DLW5BSN351SQ2
DLW5BSN191SQ2
10
1
10
100
Frequency (MHz)
1000
0
10
20
30
40
50
60
Operating Temperature (°C)
70
80
75°C
90
100
85°C
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
156
DLW Series
Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil
DLW5BT
DLW5BT
Series (2020 Size)
■ Dimensions
Chip Ferrite Bead
Low profile wire-wound common choke coil for power lines.
■ Equivalent Circuit
* The marking to
indicate the product
direction can be
applicable.
(Optional)
Polarity Marking
(2)
(1)
(3)
(4)
(4)
(2)
(3)
1.3±0.3
(1)
0.45 min.
0.5 min.
(L) 5.0±0.3
■ Packaging
: Electrode
1.3±0.3
0.9±0.3
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
700
K
330mm Reel Embossed Tape
2500
B
Bulk(Bag)
100
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW5BTN101SQ2p
100ohm(Typ.)
6000mA
50Vdc
10M ohm
125Vdc
0.009ohm±40%
DLW5BTN251SQ2p
250ohm(Typ.)
5000mA
50Vdc
10M ohm
125Vdc
0.014ohm±40%
DLW5BTN501SQ2p
500ohm(Typ.)
4000mA
50Vdc
10M ohm
125Vdc
0.019ohm±40%
DLW5BTN102SQ2p
1000ohm(Typ.)
2000mA
50Vdc
10M ohm
125Vdc
0.024ohm±40%
DLW5BTN142SQ2p
1400ohm(Typ.)
1500mA
50Vdc
10M ohm
125Vdc
0.040ohm±40%
Rated Current Rated Voltage
Withstand Voltage DC Resistance
Chip EMIFILr
1.7±0.3
1.7±0.3
3.6±0.3
(W) 5.0±0.3
(T) 2.35±0.15
No polarity.
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
■ Impedance-Frequency Characteristics (Main Items)
10000
■ Derating of Rated Current
DLW5BTN101/251/501
Common mode
DLW5BTN102SQ2
1000
6000
DLW5BTN101SQ2
Current (mA)
Impedance (Ω)
DLW5BTN501SQ2
DLW5BTN251SQ2
100
Universal Type [Power Lines/Signal Lines]
Chip Common Mode Choke Coil
7000
DLW5BTN142SQ2
5000
4750
4000
3400
3000
10
DLW5BTN101SQ2
DLW5BTN251SQ2
DLW5BTN501SQ2
DLW5BTN102SQ2
DLW5BTN142SQ2 Differential mode
1
1
10
100
Frequency (MHz)
1000
2000
1000
0
0
20
40
60
80
65
100
85
Block Type EMIFILr
Temperature (°C)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
157
DLM Series
Signal Lines Type Chip Common Mode Choke Coil
DLM11G
DLM11G
Series (0504 Size)
Chip Ferrite Bead
Audio line common choke also effective to differential mode.
■ Equivalent Circuit
(1)
(2)
(4)
(3)
0.2±0.15
No polarity.
■ Packaging
: Electrode
(in mm)
Chip EMIFILr
(3)
(4)
0.5±0.1
1.0±0.15
(2)
(1)
0.65±0.1
1.25±0.15
0.35±0.15
■ Dimensions
Code
Packaging
Minimum
Quantity
D
180mm Reel Paper Tape
10000
B
Bulk(Bag)
1000
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Common Mode Impedance
Rated Current Rated Voltage
(at 100MHz/20°C)
Part Number
DLM11GN601SD2p
600ohm±25%
100mA
5Vdc
Insulation Resistance (min.)
Withstand Voltage
DC Resistance
100M ohm
25Vdc
0.8ohm max.
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
■ Impedance-Frequency Characteristics (Main Items)
10000
DLM11GN601SD2
Differential Mode
Impedance (Ω)
100
Common Mode
DLM11GN601SD2
10
1
1
10
100
1000
Frequency (MHz)
Block Type EMIFILr
Chip Common Mode Choke Coil
Signal Lines Type
1000
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
158
DLM Series
Signal Lines Type Chip Common Mode Choke Coil
DLM2HG
DLM2HG
Series (1008 Size)
(3)
(5)
(4)
(6)
0.3±0.2
(2)
■ Equivalent Circuit
2.0±0.2
(3)
(5)
(2)
(4)
(6)
No polarity.
■ Packaging
1.2±0.2
0.4±0.2
(1)
: Electrode
(in mm)
0.8±0.1
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
3000
B
Bulk(Bag)
1000
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current
Rated Voltage
Insulation
Resistance
(min.)
DLM2HGN601SZ3p
600ohm±25%
100mA
16Vdc
100M ohm
Withstand Voltage DC Resistance
100Vdc
Chip EMIFILr
(1)
2.5±0.2
■ Dimensions
Chip Ferrite Bead
3 line audio common mode choke coil.
0.40ohm max.
Operating Temperature Range: -55°C to +85°C Number of Circuit: 1
■ Impedance-Frequency Characteristics (Main Items)
10000
100
DLM2HGN601SZ3
Signal Lines Type
Chip Common Mode Choke Coil
Impedance (Ω)
Differential Mode
DLM2HGN601SZ3
1000
Common Mode
10
1
10
100
Frequency (MHz)
1000
10000
Block Type EMIFILr
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
159
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP0NS
DLP0NS
Series (03025 Size)
Chip Ferrite Bead
03025 size, very small chip common mode choke coil, Cut-off frequency 3GHz max.
■ Dimensions
■ Equivalent Circuit
0.27±0.1
(2)
0.45±0.05
(1)
(3)
(4)
0.5±0.1
(2)
(3)
(4)
0.85±0.05
No polarity.
(1)
■ Packaging
0.20+0.05
–0.10
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
5000
B
Bulk(Bag)
500
0.65±0.05
: Electrode
Chip EMIFILr
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current
Rated Voltage
Insulation
Resistance
(min.)
Withstand Voltage
DC Resistance
DLP0NSN670HL2p
67ohm±20%
110mA
5Vdc
100M ohm
12.5Vdc
2.4ohm±25%
DLP0NSN900HL2p
90ohm±20%
100mA
5Vdc
100M ohm
12.5Vdc
3.0ohm±25%
DLP0NSN121HL2p
120ohm±20%
90mA
5Vdc
100M ohm
12.5Vdc
3.8ohm±25%
DLP0NSA150HL2p
15ohm±5ohm
100mA
5Vdc
100M ohm
12.5Vdc
0.95ohm±25%
DLP0NSC280HL2p
28ohm±20%
100mA
5Vdc
100M ohm
12.5Vdc
1.3ohm±25%
HD: for high speed differential signal lines
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics (Main Items)
DLP0NSA150HL2/DLP0NSC280HL2
10000
10000
Common Mode
DLP0NSN121HL2
1000
1000
DLP0NSN670HL2
100
DLP0NSN121HL2
10
Impedance (Ω)
DLP0NSN900HL2
Impedance (Ω)
Chip Common Mode Choke Coil
Signal Lines Type
DLP0NSN 670/900/121 HL2
Common Mode
DLP0NSC280HL2
100
DLP0NSA150HL2
10
DLP0NSN900HL2
DLP0NSC280HL2
DLP0NSA150HL2
DLP0NSN670HL2
Differential Mode
Differential Mode
1
1
1
10
100
Frequency (MHz)
1000
10000
1
10
100
Frequency (MHz)
1000
10000
DLP0NSN900HL2
DLP0NSA150HL2
0
0
2
2
DLP0NSN900HL2
DLP0NSA150HL2
Insertion Loss (dB)
Insertion Loss (dB)
Block Type EMIFILr
■ Differential Mode Transmission Characteristics (Typ.)
4
6
8
4
6
8
10
10
1
10
100
Frequency (MHz)
1000
10000
1
10
100
Frequency (MHz)
1000
10000
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
160
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP0NS Series (03025 Size)
DLP0NS
Chip Ferrite Bead
■ Differential Mode Transmission Characteristics (Typ.)
DLP0NSC280HL2
0
2
Insertion Loss (dB)
DLP0NSC280HL2
4
6
8
10
10
100
Frequency (MHz)
1000
10000
Block Type EMIFILr
Signal Lines Type
Chip Common Mode Choke Coil
Chip EMIFILr
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
161
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP11S/DLP11T
DLP11S/11T
Series (0504 Size)
Chip Ferrite Bead
6GHz cut-off frequency (for HDMI) is available.
■ Dimensions
■ Equivalent Circuit
0.3±0.1
(2)
T
(1)
(3)
(4)
No polarity.
(1)
1.0±0.1
0.55±0.1
(2)
Part Number
T
DLP11S
0.82±0.1
DLP11T
0.3±0.05
(3)
(4)
■ Packaging
Code
Packaging
Minimum
Quantity
L
180mm Reel
Embossed Tape
3000 (DLP11S)
5000 (DLP11T)
B
Bulk(Bag)
500
0.25+0.1
–0.05
: Electrode
1.25±0.1
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current
Rated Voltage
Insulation
Resistance
(min.)
Withstand Voltage
DC Resistance
DLP11SN670SL2p
67ohm±20%
180mA
5Vdc
100M ohm
12.5Vdc
1.3ohm±25%
DLP11SN121SL2p
120ohm±20%
140mA
5Vdc
100M ohm
12.5Vdc
2.0ohm±25%
DLP11SN161SL2p
160ohm±20%
120mA
5Vdc
100M ohm
12.5Vdc
2.7ohm±25%
DLP11SN900HL2p
90ohm±20%
150mA
5Vdc
100M ohm
12.5Vdc
1.5ohm±25%
DLP11SN201HL2p
200ohm±20%
110mA
5Vdc
100M ohm
12.5Vdc
3.1ohm±25%
DLP11SN241HL2p
240ohm±20%
100mA
5Vdc
100M ohm
12.5Vdc
3.5ohm±25%
DLP11SN281HL2p
280ohm±20%
90mA
5Vdc
100M ohm
12.5Vdc
4.2ohm±25%
DLP11SN331HL2p
330ohm±20%
80mA
5Vdc
100M ohm
12.5Vdc
4.9ohm±25%
DLP11SA350HL2p
35ohm±20%
170mA
5Vdc
100M ohm
12.5Vdc
0.9ohm±25%
DLP11SA670HL2p
67ohm±20%
150mA
5Vdc
100M ohm
12.5Vdc
1.2ohm±25%
DLP11SA900HL2p
90ohm±20%
150mA
5Vdc
100M ohm
12.5Vdc
1.4ohm±25%
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics
DLP11SN Series
DLP11SA Series
1000
10000
Common mode
DLP11SN331HL2
DLP11SN281HL2
Impedance (Ω)
1000
Block Type EMIFILr
HD: for high speed differential signal lines
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
DLP11SN241HL2
DLP11SN201HL2
DLP11SN161SL2
DLP11SN121SL2
DLP11SN900HL2
DLP11SN670SL2
100
10
1
1
10
Common mode
100
DLP11SN331HL2
DLP11SN281HL2
DLP11SN241HL2
DLP11SN201HL2
DLP11SN161SL2
DLP11SN121SL2
DLP11SN900HL2
DLP11SN670SL2
Differential mode
100
Frequency (MHz)
1000
10000
Impedance (Ω)
Chip Common Mode Choke Coil
Signal Lines Type
Chip EMIFILr
(in mm)
DLP11SA900HL2
DLP11SA670HL2
DLP11SA350HL2
10
DLP11SA900HL2
DLP11SA670HL2
DLP11SA350HL2
Differential mode
1
1
10
100
Frequency (MHz)
1000
10000
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
162
DLP11S/11T
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP11S/11T Series (0504 Size)
DLP11SN Series
Chip Ferrite Bead
■ Differential Mode Transmission Characteristics (Typ.)
DLP11SA Series
0
0
DLP11SA900HL2
2
2
Insertion Loss (dB)
4
6
8
4
6
8
10
10
1
10
100
Frequency (MHz)
1000
10000
1
10
100
Frequency (MHz)
1000
10000
Chip EMIFILr
Insertion Loss (dB)
DLP11SN900HL2
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current
Rated Voltage
DLP11TB800UL2p
80ohm±25%
100mA
5Vdc
DLP11TB Series
Withstand Voltage
100M ohm
12.5Vdc
HD: for high speed differential signal lines
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
Differential mode to common mode conversion characteristic (Scd21) at 2.5GHz: -40dB (typ.)
Impedance Characteristics between signal lines Z0 (TDR at 50ps): 90ohm±15ohm
■ Impedance-Frequency Characteristics
Insulation
Resistance
(min.)
DC Resistance
1.5ohm±25%
UD: for ultra high speed differential signal lines
■ Differential Mode Transmission Characteristics
DLP11TB Series
1000
0
Common Mode
DLP11TB800UL2
Impedance (Ω)
DLP11TB800UL2
DLP11TB800UL2
10
Signal Lines Type
Chip Common Mode Choke Coil
100
Insertion Loss (dB)
2
4
6
8
Differential Mode
1
10
10
100
Frequency (MHz)
1000
10000
1
10
100
Frequency (MHz)
1000
10000
Block Type EMIFILr
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
163
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP31S
DLP31S
Series (1206 Size)
Chip Ferrite Bead
1206 size film type chip common mode choke coil.
■ Dimensions
■ Equivalent Circuit
0.7±0.2
(2)
1.15±0.15
(1)
(2.1)
1.6±0.15
(3)
(4)
3.2±0.15
(1)
No polarity.
(2)
■ Packaging
(4)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
3000
B
Bulk(Bag)
500
(3)
: Electrode
0.3±0.2
Chip EMIFILr
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLP31SN121ML2p
120ohm±20%
100mA
16Vdc
100M ohm
40Vdc
2.0ohm max.
DLP31SN221ML2p
220ohm±20%
100mA
16Vdc
100M ohm
40Vdc
2.5ohm max.
DLP31SN551ML2p
550ohm±20%
100mA
16Vdc
100M ohm
40Vdc
Rated Current Rated Voltage
Withstand Voltage DC Resistance
HD: for high speed differential signal lines
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
3.6ohm max.
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics (Main Items)
10000
1000
Impedance (Ω)
100
Common mode
10
DLP31SN121ML2
DLP31SN221ML2
DLP31SN551ML2
Differential mode
1
1
10
100
1000
Frequency (MHz)
Block Type EMIFILr
Chip Common Mode Choke Coil
Signal Lines Type
DLP31SN551ML2
DLP31SN221ML2
DLP31SN121ML2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
164
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP1ND
DLP1ND
Series (0502 Size)
■ Dimensions
■ Equivalent Circuit
(1)
(2)
(3)
(4)
(5)
(6)
(7)
No polarity.
(8)
(3)
(4)
(5)
(6)
(7)
(8)
■ Packaging
1.5±0.1
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
5000
B
Bulk(Bag)
500
: Electrode
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Common Mode Impedance
Rated Current Rated Voltage
(at 100MHz/20°C)
Part Number
DLP1NDN350HL4p
35ohm±20%
100mA
5Vdc
100M ohm
12.5Vdc
1.8ohm±25%
DLP1NDN670HL4p
67ohm±20%
80mA
5Vdc
100M ohm
12.5Vdc
2.9ohm±25%
DLP1NDN900HL4p
90ohm±20%
60mA
5Vdc
100M ohm
12.5Vdc
Operating Temperature Range: -40°C to +85°C Number of Circuit: 2
HD: for high speed differential signal lines
■ Impedance-Frequency Characteristics
3.7ohm±25%
UD: for ultra high speed differential signal lines
■ Differential Mode Transmission Characteristics
0
10000
Common mode
-2
DLP1NDN900HL4
Insertion Loss (dB)
DLP1NDN900HL4
DLP1NDN670HL4
DLP1NDN350HL4
100
Signal Lines Type
Chip Common Mode Choke Coil
1000
Impedance (Ω)
Insulation
Resistance Withstand Voltage DC Resistance
(min.)
Chip EMIFILr
(2)
0.1 min.
(1)
0.45±0.05
0.4±0.1
0.65±0.1
0.2±0.1
0.2±0.1
Chip Ferrite Bead
2 circuits in 05025 size, adapt to HDMI line.
-4
-6
DLP1NDN350HL4
10
DLP1NDN670HL4
-8
DLP1NDN900HL4
Differential mode
-10
1
10
100
Frequency (MHz)
1000
10000
10
100
1000
10000
Frequency (MHz)
Block Type EMIFILr
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
165
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP2AD
DLP2AD
Series (0804 Size)
Chip Ferrite Bead
2 circuit built-in, 0804 size, HDMI adapted type available, cut-off frequency 6GHz max.
■ Dimensions
■ Equivalent Circuit
0.5±0.1
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1.0±0.1
0.25±0.15
(1)
(3)
(4)
(5)
(6)
(7)
No polarity.
(8)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
3000
B
Bulk(Bag)
500
: Electrode
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated
Current
Rated
Voltage
Insulation
Resistance
(min.)
Withstand
Voltage
DC Resistance
DLP2ADA350HL4p
35ohm±20%
150mA
5Vdc
100M ohm
12.5Vdc
0.8ohm±25%
DLP2ADA670HL4p
67ohm±20%
130mA
5Vdc
100M ohm
12.5Vdc
1.0ohm±25%
DLP2ADA900HL4p
90ohm±20%
120mA
5Vdc
100M ohm
12.5Vdc
1.4ohm±25%
DLP2ADN670HL4p
67ohm±20%
140mA
5Vdc
100M ohm
12.5Vdc
1.3ohm±25%
DLP2ADN900HL4p
90ohm±20%
130mA
5Vdc
100M ohm
12.5Vdc
1.7ohm±25%
DLP2ADN121HL4p
120ohm±20%
120mA
5Vdc
100M ohm
12.5Vdc
2.0ohm±25%
DLP2ADN161HL4p
160ohm±20%
100mA
5Vdc
100M ohm
12.5Vdc
2.5ohm±25%
DLP2ADN201HL4p
200ohm±20%
90mA
5Vdc
100M ohm
12.5Vdc
3.2ohm±25%
DLP2ADN241HL4p
240ohm±20%
80mA
5Vdc
100M ohm
12.5Vdc
3.8ohm±25%
DLP2ADN281HL4p
280ohm±20%
80mA
5Vdc
100M ohm
12.5Vdc
Operating Temperature Range: -40°C to +85°C Number of Circuit: 2
HD: for high speed differential signal lines
4.6ohm±25%
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics (Main Items)
DLP2ADA Series
DLP2ADN Series
10000
1000
Common Mode
Common mode
DLP2ADN281HL4
DLP2ADN241HL4
DLP2ADN201HL4
DLP2ADN161HL4
DLP2ADN121HL4
DLP2ADN900HL4
DLP2ADN670HL4
DLP2ADA900HL4
1000
Impedance (Ω)
DLP2ADA670HL4
100
DLP2ADA350HL4
DLP2ADA900HL4
Impedance (Ω)
Chip EMIFILr
(2)
■ Packaging
2.0±0.1
Chip Common Mode Choke Coil
Signal Lines Type
(1)
0.82±0.1
0.25±0.1
100
10
10
Block Type EMIFILr
DLP2ADA670HL4
DLP2ADA350HL4
Differential Mode
1
1
10
100
Frequency (MHz)
1000
10000
DLP2ADN670HL4
1
1
10
DLP2ADN281HL4
DLP2ADN241HL4
DLP2ADN201HL4
DLP2ADN161HL4
DLP2ADN121HL4
Differential mode
DLP2ADN900HL4
100
Frequency (MHz)
1000
10000
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
166
DLP2AD
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP2AD Series (0504 Size)
DLP2ADA Series
Chip Ferrite Bead
■ Differential Mode Transmission Characteristics (Typ.)
DLP2ADN Series
0
0
2
2
DLP2ADA900HL4
Insertion Loss (dB)
Insertion Loss (dB)
DLP2ADN900HL4
DLP2ADA670HL4
4
DLP2ADA350HL4
6
4
6
8
8
10
10
10
100
1000
10000
1
10
100
Frequency (MHz)
1000
10000
Block Type EMIFILr
Signal Lines Type
Chip Common Mode Choke Coil
Chip EMIFILr
Frequency (MHz)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
167
DLP Series
Signal Lines Type Chip Common Mode Choke Coil
DLP31D
DLP31D
Series (1206 Size)
Chip Ferrite Bead
2 circuit built-in, 1206 size, meet IEEE1394,USB,LVDS.
■ Equivalent Circuit
(2)
(3)
(4)
(2)
(3)
(4)
(5)
(6)
(7)
No polarity.
(8)
■ Packaging
1.6±0.15
(1)
0.8±0.1
0.3±0.2
0.4±0.2
(5)
(6)
(7)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
3000
B
Bulk(Bag)
500
(8)
: Electrode
3.2±0.15
(in mm)
Chip EMIFILr
(1)
1.15±0.15
■ Dimensions
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLP31DN900ML4p
90ohm±20%
160mA
10Vdc
100M ohm
25Vdc
1.1ohm max.
DLP31DN131ML4p
130ohm±20%
120mA
10Vdc
100M ohm
25Vdc
1.1ohm max.
DLP31DN201ML4p
200ohm±20%
100mA
10Vdc
100M ohm
25Vdc
2.2ohm max.
DLP31DN321ML4p
320ohm±20%
80mA
10Vdc
100M ohm
25Vdc
3.5ohm max.
DLP31DN441ML4p
440ohm±20%
70mA
10Vdc
100M ohm
25Vdc
Rated Current Rated Voltage
Operating Temperature Range: -40°C to +85°C Number of Circuit: 2
Withstand Voltage DC Resistance
HD: for high speed differential signal lines
4.3ohm max.
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics (Main Items)
10000
DLP31DN441ML4
DLP31DN321ML4
DLP31DN201ML4
DLP31DN131ML4
DLP31DN900ML4
1000
Impedance (Ω)
Chip Common Mode Choke Coil
Signal Lines Type
Common mode
100
DLP31DN441ML4
DLP31DN321ML4
10
DLP31DN900ML4
DLP31DN131ML4
DLP31DN201ML4 Differential mode
1
1
10
100
1000
Block Type EMIFILr
Frequency (MHz)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
168
DLW Series
Signal Lines Type Chip Common Mode Choke Coil
DLW21S
DLW21S
Series (0805 Size)
■ Dimensions
■ Equivalent Circuit
(2)
(0.17)
1.2±0.2
(1)
2.0±0.2
(3)
(4)
1.2±0.2
No polarity.
(0.45)
(0.45)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
2000
B
Bulk(Bag)
500
: Electrode
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
Rated Current
Rated Voltage
Insulation
Resistance
(min.)
Withstand Voltage
DC Resistance
DLW21SN670SQ2p
67ohm±25%
400mA
50Vdc
10M ohm
125Vdc
0.25ohm max.
DLW21SN900SQ2p
90ohm±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
DLW21SN121SQ2p
120ohm±25%
370mA
50Vdc
10M ohm
125Vdc
0.45ohm max.
DLW21SN181SQ2p
180ohm±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
DLW21SN261SQ2p
260ohm±25%
300mA
50Vdc
10M ohm
125Vdc
0.40ohm max.
DLW21SN371SQ2p
370ohm±25%
280mA
50Vdc
10M ohm
125Vdc
0.45ohm max.
DLW21SN670HQ2p
67ohm±25%
320mA
20Vdc
10M ohm
50Vdc
0.31ohm max.
DLW21SN900HQ2p
90ohm±25%
280mA
20Vdc
10M ohm
50Vdc
0.41ohm max.
DLW21SN121HQ2p
120ohm±25%
280mA
20Vdc
10M ohm
50Vdc
0.41ohm max.
DLW21SR670HQ2p
67ohm±25%
400mA
20Vdc
10M ohm
50Vdc
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
HD: for high speed differential signal lines
0.25ohm max.
UD: for ultra high speed differential signal lines
DLW21SR670HQ2 is designed to correct line impedance when ESD protection device is also used.
■ Impedance-Frequency Characteristics (Main Items)
DLW21SN_SQ2 Series
DLW21SN_HQ2 Series
1000
Impedance (Ω)
1000
Common mode
Common mode
100
Impedance (Ω)
DLW21SN371SQ2
DLW21SN261SQ2
DLW21SN181SQ2
DLW21SN121SQ2
DLW21SN900SQ2
DLW21SN670SQ2
100
10
1
Differential mode
0.1
1
DLW21SN371SQ2
DLW21SN261SQ2
DLW21SN181SQ2
DLW21SN121SQ2
DLW21SN900SQ2
DLW21SN670SQ2
10
100
Frequency (MHz)
1000
DLW21SN121HQ2
DLW21SN900HQ2
DLW21SN670HQ2
10
1
DLW21SN121HQ2
Block Type EMIFILr
10000
Chip EMIFILr
(3)
■ Packaging
Signal Lines Type
Chip Common Mode Choke Coil
(4)
(0.4)
(2)
(0.4)
(1)
Chip Ferrite Bead
Wire-wound common choke, HDMI available type prepaird.
DLW21SN900HQ2
DLW21SN670HQ2
Differential mode
0.1
10
100
Frequency (MHz)
1000
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
169
DLW Series
Signal Lines Type Chip Common Mode Choke Coil
DLW21S Series (0805 Size)
DLW21S
DLW21SR_HQ2 Series
1000
Common mode
100
DLW21SR670HQ2
Impedance (Ω)
Chip Ferrite Bead
■ Impedance-Frequency Characteristics (Main Items)
10
Differential mode
1
DLW21SR670HQ2
0.1
1
10
100
1000
Chip EMIFILr
Frequency (MHz)
■ Differential Mode Transmission Characteristics (Typ.)
DLW21SN_HQ2 Series
0
DLW21SN900HQ2
Insertion Loss (dB)
2
4
6
8
10
10
100
Frequency (MHz)
1000
10000
Block Type EMIFILr
Chip Common Mode Choke Coil
Signal Lines Type
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
170
DLW Series
Signal Lines Type Chip Common Mode Choke Coil
DLW21H
DLW21H
Series (0805 Size)
■ Dimensions
Chip Ferrite Bead
Low profile wire-wound common choke coil.
■ Equivalent Circuit
(2)
(0.17)
0.9±0.1
(1)
2.0±0.2
1.2±0.2
(3)
(4)
No polarity.
(2)
■ Packaging
(0.4)
(4)
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
3000
B
Bulk(Bag)
500
: Electrode
(3)
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW21HN670SQ2p
67ohm±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
DLW21HN900SQ2p
90ohm±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
DLW21HN121SQ2p
120ohm±25%
280mA
50Vdc
10M ohm
125Vdc
0.45ohm max.
DLW21HN181SQ2p
180ohm±25%
250mA
50Vdc
10M ohm
125Vdc
Rated Current Rated Voltage
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
Withstand Voltage DC Resistance
HD: for high speed differential signal lines
Chip EMIFILr
(0.45)
(1)
(0.4)
(0.45)
0.50ohm max.
UD: for ultra high speed differential signal lines
■ Impedance-Frequency Characteristics (Main Items)
10000
DLW21HN181SQ2
Common mode
1000
Signal Lines Type
Chip Common Mode Choke Coil
Impedance (Ω)
DLW21HN121SQ2
DLW21HN900SQ2
100
DLW21HN670SQ2
10
DLW21HN181SQ2
DLW21HN121SQ2
1
DLW21HN900SQ2
Differential mode
DLW21HN670SQ2
0.1
1
10
100
1000
Block Type EMIFILr
Frequency (MHz)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
171
DLW Series
Signal Lines Type Chip Common Mode Choke Coil
DLW31S
DLW31S
Series (1206 Size)
Chip Ferrite Bead
1206 size wire-wound common mode choke coil.
■ Dimensions
■ Equivalent Circuit
(2)
(0.25)
1.9±0.2
(1)
3.2±0.2
(3)
(4)
1.6±0.2
No polarity.
(4)
■ Packaging
Code
Packaging
Minimum
Quantity
L
180mm Reel Embossed Tape
2000
B
Bulk(Bag)
500
(3)
: Electrode
(0.6)
(0.6)
Chip EMIFILr
(0.6)
(2)
(0.6)
(1)
(in mm)
Refer to pages from p.176 to p.179 for mounting information.
■ Rated Value (p: packaging code)
Insulation
Resistance
(min.)
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW31SN900SQ2p
90ohm±25%
370mA
50Vdc
10M ohm
125Vdc
0.3ohm max.
DLW31SN161SQ2p
160ohm±25%
340mA
50Vdc
10M ohm
125Vdc
0.4ohm max.
DLW31SN261SQ2p
260ohm±25%
310mA
50Vdc
10M ohm
125Vdc
0.5ohm max.
DLW31SN601SQ2p
600ohm±25%
260mA
50Vdc
10M ohm
125Vdc
0.8ohm max.
DLW31SN102SQ2p
1000ohm±25%
230mA
50Vdc
10M ohm
125Vdc
1.0ohm max.
DLW31SN222SQ2p
2200ohm±25%
200mA
50Vdc
10M ohm
125Vdc
Rated Current Rated Voltage
Operating Temperature Range: -40°C to +85°C Number of Circuit: 1
Withstand Voltage DC Resistance
HD: for high speed differential signal lines
1.2ohm max.
UD: for ultra high speed differential signal lines
10000
DLW31SN222SQ2
DLW31SN102SQ2
DLW31SN601SQ2
DLW31SN261SQ2
DLW31SN161SQ2
DLW31SN900SQ2
Common mode
1000
Impedance (Ω)
Chip Common Mode Choke Coil
Signal Lines Type
■ Impedance-Frequency Characteristics
100
10
DLW31SN222SQ2
DLW31SN102SQ2
DLW31SN601SQ2
DLW31SN261SQ2
DLW31SN161SQ2
DLW31SN900SQ2
Differential mode
1
0.1
1
10
100
1000
Block Type EMIFILr
Frequency (MHz)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
172
PLT Series
Power Lines Type Large Current Common Mode Choke Coil for Automotive Available
PLT10H
PLT10H
Series (12.9x6.6 mm)
■ Dimensions
Chip Ferrite Bead
Automotive available, up to 10A.
■ Equivalent Circuit
(1) (2)
(2)
(1)
102
(4) (3)
6.6±0.2
12.9±0.2
(3)
(4)
Code
Packaging
Minimum
Quantity
9.1±0.2
: Electrode
1.0±0.2
L
180mm Reel Embossed Tape
125
K
330mm Reel Embossed Tape
500
B
Bulk(Bag)
50
(in mm)
3.2±0.3
Refer to pages from p.180 to p.181 for mounting information.
■ Rated Value (p: packaging code)
Part Number
Common Mode
Impedance
(at 10MHz/20°C)
Rated
Current
Rated
Voltage
Insulation
Resistance
(min.)
Withstand
Voltage
DC Resistance
Common Mode
Inductance
PLT10HH401100PNp
400ohm
10A
100Vdc
10M ohm
250Vdc
3.6m ohm±0.5m ohm
6µH min.
PLT10HH501100PNp
500ohm
10A
100Vdc
10M ohm
250Vdc
3.6m ohm±0.5m ohm
9µH min.
PLT10HH9016R0PNp
900ohm
6A
100Vdc
10M ohm
250Vdc
8.0m ohm±0.5m ohm
14µH min.
PLT10HH1026R0PNp
1000ohm
6A
100Vdc
10M ohm
250Vdc
8.0m ohm±0.5m ohm
20µH min.
Chip EMIFILr
1.0±0.2
■ Packaging
2.1±0.3
2.1±0.3
13.4 max.
9.4 max.
2.0±0.3
No polarity.
Operating Temperature Range (Self-temperature rise is included): -55°C to +105°C (PLT10HH 1026R0/501100 PN), -55°C to +105°C (PLT10HH 401100/9016R0 PN) Number of Circuit: 1
■ Impedance-Frequency Characteristics
Imredance (Ω)
1000
Derating
PLT10HH501100PN
12
PLT10HH401100PN
10
100
Frequency (MHz)
1000
Current [A]
10
PLT10HH401
8
10
1
Power Lines Type
Chip Common Mode Choke Coil
PLT10HH1026R0PN
PLT10HH9016R0PN
100
■ Notice (Rating)
In operating temperature exceeding +65°C,
derating of current is necessary for
PLT10H Series.
Please apply the derating curve shown in
chart according to the operating
temperature.
10000
PLT10HH501
PLT10HH901
6
4
2
PLT10HH102
0
0
20
40
60
80
100
120
140
Block Type EMIFILr
Operating Temperature [°C]
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
173
Chip Common Mode Choke Coil
!Caution/Notice
Chip Ferrite Bead
!Caution
● Rating
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
● Soldering and Mounting
2. Mounting Direction
Mount Chip Common Mode Choke Coils in right
direction. Wrong direction, which is 90 degrees rotated
from right direction, causes not only open or short
circuit but also flames or other serious trouble.
Z
right direction
Z
wrong direction
Notice
● Storage and Operating Conditions
● Handling
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
Do not use products in the environment close to the
organic solvent.
<Storage and Handling Requirements>
1. Storage Period
DLW11G/DLM2HG series should be used within 6
months, the other series should be used within 12
months.
Solderability should be checked if this period is
exceeded.
2. Storage Conditions
(1) Storage temperature: -10 to +40˚C
Relative humidity: 15 to 85%
Avoid sudden changes in temperature and humidity.
(2) Do not store products in a chemical atmosphere
such as chlorine gas, acid or sulfide gas.
1. Resin Coating (Except DLW Series.)
Using resin for coating/molding products may affect
the products performance.
So please pay careful attention in selecting resin.
Prior to use, please make the reliability evaluation with
the product mounted in your application set.
2. Resin Coating (DLW Series)
The impedance value may change due to high curestress of resin to be used for coating/molding products.
An open circuit issue may occur by mechanical stress
caused by the resin, amount/cured shape of resin, or
operating condition etc. Some resin contains some
impurities or chloride possible to generate chlorine by
hydrolysis under some operating condition may cause
corrosion of wire of coil, leading to open circuit.
So, please pay your careful attention in selecting resin
in case of coating/molding the products with the resin.
Prior to use the coating resin, please make sure no
reliability issue is observed by evaluating products
mounted on your board.
3. Caution for Use (DLW Series)
When you hold products with a tweezer, please hold
by the sides. Sharp materials, such as a pair of
tweezers, should not touch the winding portion to
prevent breaking the wire. Mechanical shock should
not be applied to the products mounted on the board
to prevent breaking the core.
4. Brushing
When you clean the neighborhood of products such
as connector pins, bristles of cleaning brush shall not
be touched to the winding portion of this product to
prevent the breaking of wire.
5. Handling of a Substrate
After mounting products on a substrate, do not apply
any stress to the product caused by bending or
twisting to the substrate when cropping the substrate,
inserting and removing a connector from the substrate
or tightening screw to the substrate. Excessive
mechanical stress may cause cracking in the Product.
● Notice (Soldering and Mounting)
1. Cleaning
Failure and degradation of a product are caused by
the cleaning method. When you clean in conditions
that are not in mounting information, please contact
Murata engineering.
2. Soldering
Reliability decreases with improper soldering methods.
Please solder by the standard soldering conditions
shown in mounting information.
3. Other
Noise suppression levels resulting from Murata's EMI
suppression filters EMIFILr may vary, depending on
the circuits and ICs used, type of noise, mounting
pattern, mounting location, and other operating
conditions. Be sure to check and confirm in advance
the noise suppression effect of each filter, in actual
circuits, etc. before applying the filter in a commercialpurpose equipment design.
Block Type EMIFILr
!Caution/ Chip Common Mode Choke Coil
Notice
Chip EMIFILr
1. Self-heating
Please provide special attention when mounting chip
common mode choke coils DLW5 series in close
proximity to other products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in
this component.
Bending
Twisting
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
174
Chip Common Mode Choke Coil
!Caution/Notice
● Rating
1. Do not use products beyond the rated current and
rated voltage as this may create excessive heat and
deteriorate the insulation resistance.
2. Be sure to provide an appropriate fail-safe function on
your product to prevent a second damage that may be
caused by the abnormal function or the failure our
product.
Chip Ferrite Bead
!Caution
2. Mounting Direction
Mount Chip Common Mode Choke Coils in right
direction. Wrong direction, which is 90 degrees
rotated from right direction, causes not only open or
short circuit but also flames or other serious trouble.
Z
Z
● Soldering and Mounting
1. Self-heating
Please provide special attention when mounting chip
common mode choke coils in close proximity to other
products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in
this component.
wrong direction
Chip EMIFILr
right direction
● Storage and Operating Conditions
● Notice (Soldering and Mounting)
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
Do not use products in the environment close to the
organic solvent.
<Storage and Handling Requirements>
1. Storage Period
PLT10H series should be used within 12 months.
Solderability should be checked if this period is
exceeded.
2. Storage Conditions
(1) Storage temperature: -10 to +40˚C
Relative humidity: 15 to 85%
Avoid sudden changes in temperature and humidity.
(2) Do not store products in a chemical atmosphere
such as chlorine gas, acid or sulfide gas.
1. Cleaning
Failure and degradation of a product are caused by
the cleaning method. When you clean in conditions
that are not in mounting information, please contact
Murata engineering.
2. Soldering
Reliability decreases with improper soldering methods.
Please solder by the standard soldering conditions
shown in mounting information.
3. Other
Noise suppression levels resulting from Murata's EMI
suppression filters EMIFILr may vary, depending on
the circuits and ICs used, type of noise, mounting
pattern, mounting location, and other operating
conditions. Be sure to check and confirm in advance
the noise suppression effect of each filter, in actual
circuits, etc. before applying the filter in a commercialpurpose equipment design.
!Caution/
Chip Common Mode Choke Coil
Notice
Notice
● Handling
Bending
Block Type EMIFILr
1. Handling of a Substrate
After mounting products on a substrate, do not apply
any stress to the product caused by bending or
twisting to the substrate when cropping the substrate,
inserting and removing a connector from the substrate
or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in
the Product.
Twisting
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
175
DL p
Soldering and Mounting
Chip Common Mode Choke Coil
Chip EMIFILr
Land Pattern
+ Solder Resist
Land Pattern
Solder Resist
(in mm)
oReflow and Flow
DLM2HG
DLP31D
DLP31S
0.7
0.8
2.2-2.6
0.7
2.8
2.1
DLM11G
DLM2HG
DLP0NS
DLP11S
DLP11T
DLP1ND
DLP2AD
DLP31S
DLP31D
DLW21S
DLW21H
DLW31SN
DLW5AH
DLW5B
2.0
1.2
0.4
Chip Ferrite Bead
1. Standard Land Pattern Dimensions
1.0
4.0
1.0 0.6 1.0
0.8 Pitch
0.4
oReflow Soldering
DLP0NS
DLP11S
DLP11T
DLP1ND
1.4
0.2
0.85
1.55
DLM11G
0.4
∗2
DLW21S/21H/31SN
d
1.5
0.4
Soldering
Chip Common Mode Choke Coil
and Mounting
1.1
0.3
∗1
c
1.75
0.25
0.5
1.5
∗3
a
b
0.5
Series
4.7
3.3
1.3
DLW5AH/5B
Block Type EMIFILr
0.3
0.55
1.95
DLP2AD
0.9
0.3
0.85
0.3
0.55
0.90
0.55
0.3
0.55
0.80
0.50
0.3
0.30
0.9
2.9
5.5
o PCB Warping
PCB should be designed so that products are not
subjected to the mechanical stress caused by warping
the board.
a
b
c
d
DLW21S/H
0.8
2.6
0.4
1.2
DLW31SN
1.6
3.7
0.4
1.6
∗1: If the pattern is made with wider than 1.2mm (DLW21) /
1.6mm (DLW31S) it may result in components turning
around, because melting speed is different. In the worst
case, short circuit between lines may occur.
∗2: If the pattern is made with less than 0.4mm, in the worst
case, short circuit between lines may occur due to spread
of soldering paste or mount placing accuracy.
∗3: If the pattern is made with wider than 0.8mm (DLW21) /
1.6mm (DLW31SN), the bending strength will be reduced.
Do not use gild pattern; excess soldering heat may dissolve
metal of a copper wire.
Products should be located in the sideways direction
(Length: a<b) to the mechanical stress.
a
b
Poor example
Good example
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
176
DLp Chip Common Mode Choke Coil
Soldering and Mounting
2. Solder Paste Printing and Adhesive Application
Chip Ferrite Bead
When flow soldering the chip common mode choke coils,
apply the adhesive in accordance with the following
conditions.
If too much adhesive is applied, then it may overflow into
the land or termination areas and yield poor solderability.
In contrast, if insufficient adhesive is applied, or if the
adhesive is not sufficiently hardened, then the chip may
become detached during flow soldering process.
When reflow soldering the chip common mode choke
coils, the printing must be conducted in accordance with
the following cream solder printing conditions.
If too much solder is applied, the chip will be prone to
damage by mechanical and thermal stress from the PCB
and may crack.
Standard land dimensions should be used for resist and
copper foil patterns.
(in mm)
DLP
DLW
DLM
Solder Paste Printing
Adhesive Application
oGuideline of solder paste thickness:
100-150µm: DLW21S/21H/31S,
DLP0NS/11S/11T/1ND/2AD/DLM11G
150-200µm: DLP31D/31S, DLM2HG,
DLW5AH/5BS/5BT
*Solderability is subject to reflow conditions and
thermal conductivity. Please make sure that your
product has been evaluated in view of your
specifications with our product being mounted to your
product.
DLP31D
DLP31S
Coating Position of
Bonding Agent
DLW21S/21H/31S
d
c
c
DLP0NS/11S/11T/31S/DLM11G
DLP31S/DLM2HG/DLP31D
Apply 0.3mg of bonding agent at each chip.
Chip EMIFILr
Series
Coating Position of
Bonding Agent
d
DLM2HG
c
a
b
Series
b
a
a
b
Coating Position of
Bonding Agent
c
d
DLP0NS 0.3 0.3 0.3 0.5
DLP11S
0.7 0.55 0.3 0.55
DLP11T
0.5 0.55 0.3 0.55
DLP31S
1.0 0.6 0.7 2.1
Series
a
b
c
d
Soldering
and Mounting Chip Common Mode Choke Coil
a
DLW21S/H 0.8 2.6 0.5 1.2
DLW31S
1.6 3.7 0.4 1.6
DLM11G 0.5 0.5 0.4 0.7
DLP2AD/31D
c
a
b
c
d
a
Series
b
DLP2AD 0.55 0.4 0.25 0.5
a
DLP1ND 0.3 0.3 0.2 0.4
DLP31D
1.0 0.8 0.4 0.8
d
3.3
4.7
1.3
2.0
1.2
0.4
5.5
2.9
0.9
Block Type EMIFILr
DLM2HG
DLW5AH/5BS/5BT
1.0
4.0
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
177
DLp Chip Common Mode Choke Coil
Soldering and Mounting
Chip Ferrite Bead
3. Standard Soldering Conditions
Flux:
o Use Rosin-based flux.
In case of DLW21/31 series, use Rosin-based flux with
converting chlorine content of 0.06 to 0.1wt%.
In case of using RA type solder, products should be
cleaned completely with no residual flux.
o Do not use strong acidic flux (with chlorine content
exceeding 0.20wt%)
o Do not use water-soluble flux.
(1) Soldering Methods
Use flow and reflow soldering methods only.
Use standard soldering conditions when soldering chip
common mode choke coils.
In cases where several different parts are soldered, each
having different soldering conditions, use those
conditions requiring the least heat and minimum time.
Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based
solder will deteriorate performance of products.
If using DLP/DLM series with Sn-Zn based solder,
please contact Murata in advance.
For additional mounting methods, please contact Murata.
oFlow Soldering Profile
(Sn-3.0Ag-0.5Cu Solder)
Temperature (°C)
Chip EMIFILr
(2) Soldering Profile
T3
T2
t2
Heating
T1
Standard Profile
Pre-heating
t1
Standard Profile
Heating
Temp. (T1)
Time. (t1)
Temp. (T2)
Time. (t2)
150°C
60s min.
250°C
4 to 6s
Limit Profile
Cycle
of Flow
Heating
Temp. (T3)
Time. (t2)
265±3°C
5s max.
2 times
max.
Cycle
of Flow
2 times
max.
oReflow Soldering Profile
(Sn-3.0Ag-0.5Cu Solder)
Temperature (°C)
T4
T2
T1
T3
180
150
Limit Profile
Pre-heating
t1
Standard Profile
t2
90s±30s
Block Type EMIFILr
Soldering
Chip Common Mode Choke Coil
and Mounting
DLM2HG
DLP31D/31S
Time (s)
Pre-heating
Series
Limit Profile
time (s)
Standard Profile
Series
Limit Profile
Temp. (T3)
Peak
Cycle
Temperature
of Reflow
(T4)
Time. (t2)
245±3°C
2 times
max.
230°C min.
60s max.
260°C/10s
2 times
max.
250±3°C
2 times
max.
230°C min.
60s max.
260°C/10s
2 times
max.
Peak
Cycle
Temperature
of Reflow
(T2)
Time. (t1)
Heating
Temp. (T1)
DLM/DLP
DLW21/31
220°C min.
30 to 60s
DLW5A/5B
220°C min.
30 to 60s
Heating
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
178
Soldering and Mounting
(3) Reworking with Solder Iron
The following conditions must be strictly followed when
using a soldering iron.
Pre-heating: 150°C 60s min.
Soldering iron power output / Tip diameter:
30W max. / ø3mm max.
Temperature of soldering iron tip / Soldering time / Times:
350°C max. / 3-4s / 2 times*1
1
* DLP0NS, DLP11S, DLP11T, DLP1ND, DLP2AD:
380°C max. / 3-4s / 2 times
Do not allow the tip of the soldering iron to directly
contact the chip.
For additional methods of reworking with a soldering iron,
please contact Murata engineering.
Chip Ferrite Bead
DLp Chip Common Mode Choke Coil
4. Cleaning
Chip EMIFILr
Before cleaning, please contact Murata engineering.
(a) Alcohol cleaning agent
Isopropyl alcohol (IPA)
(b) Aqueous cleaning agent
Pine Alpha ST-100S
(4) Ensure that flux residue is completely removed.
Component should be thoroughly dried after aqueous
agent has been removed with deionized water.
Block Type EMIFILr
Soldering
and Mounting Chip Common Mode Choke Coil
Following conditions should be observed when cleaning
chip EMI filter.
(1) Cleaning Temperature: 60°C max. (40°C max. for
alcohol type cleaner)
(2) Ultrasonic
Output: 20W/liter max.
Duration: 5 minutes max.
Frequency: 28 to 40kHz
(3) Cleaning agent
The following list of cleaning agents have been tested on
the individual components. Evaluation of final assembly
should be completed prior to production.
Do not clean DLW (except DLW21H) series.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
179
PL p
Chip Common Mode Choke Coil
Soldering and Mounting
(in mm)
PLT10H
Copper Foil Pattern
Copper Foil Pattern + Resist
Resist
oReflow Soldering
PLT10H
2.0 2.5 2.0
Chip Ferrite Bead
1. Standard Land Pattern Dimensions
4.0
8.0
4.0
Chip EMIFILr
o PCB Warping
PCB should be designed so that products are not
subjected to the mechanical stress caused by warping
the board.
Products should be located in the sideways direction
(Length: a<b) to the mechanical stress.
a
b
Poor example
Good example
When reflow soldering the chip common mode choke
coils, the printing must be conducted in accordance with
the following cream solder printing conditions.
If too much solder is applied, the chip will be prone to
damage by mechanical and thermal stress from the PCB
and may crack.
Standard land dimensions should be used for resist and
copper foil patterns.
Series
PLT10H
When flow soldering the chip common mode choke coils,
apply the adhesive in accordance with the following
conditions.
If too much adhesive is applied, then it may overflow into
the land or termination areas and yield poor solderability.
In contrast, if insufficient adhesive is applied, or if the
adhesive is not sufficiently hardened, then the chip may
become detached during flow soldering process.
Solder Paste Printing
oGuideline of solder paste thickness:
150-200µm: PLT10H
For the solder paste printing pattern, use standard land dimensions.
*Solderability is subject to reflow conditions and thermal conductivity. Please make sure that your
product has been evaluated in view of your specifications with our product being mounted to your
product.
Block Type EMIFILr
Soldering
Chip Common Mode Choke Coil
and Mounting
2. Solder Paste Printing and Adhesive Application
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
180
PLp Chip Common Mode Choke Coil
Soldering and Mounting
3. Standard Soldering Conditions
(1) Soldering Methods
Use reflow soldering methods only.
Use standard soldering conditions when soldering chip
common mode choke coils.
In cases where several different parts are soldered, each
having different soldering conditions, use those
conditions requiring the least heat and minimum time.
Chip Ferrite Bead
Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based
solder will deteriorate performance of products.
Flux:
o Use Rosin-based flux.
use Rosin-based flux.
o Do not use strong acidic flux (with chlorine content
exceeding 0.20wt%)
o Do not use water-soluble flux.
For additional mounting methods, please contact Murata.
(2) Soldering Profile
Chip EMIFILr
oReflow Soldering Profile
(Sn-3.0Ag-0.5Cu Solder)
Temperature (°C)
T4
T2
T1
T3
180
150
Limit Profile
Pre-heating
t1
Standard Profile
t2
time (s)
Standard Profile
Series
Temp. (T1)
PLT10H
Limit Profile
Peak
Cycle
Temperature
of Reflow
(T2)
Time. (t1)
Heating
220°C min.
30 to 60s
250±3°C
(3) Reworking with Solder Iron
The following conditions must be strictly followed when
using a soldering iron.
Pre-heating: 150°C 60s min.
Soldering iron power output / Tip diameter:
80W max. / ø3mm max.
Temperature of soldering iron tip / Soldering time / Times:
400°C max. / 5s / 2 times
2 times
max.
Heating
Temp. (T3)
Time. (t2)
230°C min.
60s max.
Peak
Cycle
Temperature
of Reflow
(T4)
260°C/10s
2 times
max.
Soldering
and Mounting Chip Common Mode Choke Coil
90s±30s
Do not allow the tip of the soldering iron to directly
contact the chip.
For additional methods of reworking with a soldering iron,
please contact Murata engineering.
Block Type EMIFILr
4. Cleaning
Do not clean after soldering. If cleaning, please contact us.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
181
DL p
Packaging
Chip Common Mode Choke Coil
Minimum Quantity and Dimensions of 8mm Width Paper / Embossed Tape
<Paper>
1.75±0.1
<Embossed>
c
d
3.5±0.05
8.0
a
Chip Ferrite Bead
2.0±0.05
∗1 4.0±0.1 4.0±0.1 ø1.5 +0.1
-0
c
Direction of Feed
b
c: Depth of Cavity
(Embossed Tape)
∗1 DLM11G: 2.0±0.05
c: Total Thickness of Tape
(Paper Tape)
Dimension of the cavity of embossed tape is measured at the bottom side.
Part Number
a
Chip EMIFILr
Minimum Qty. (pcs.)
Cavity Size
b
c
ø330mm Reel
ø180mm Reel
d
Paper Tape Embossed Tape Paper Tape Embossed Tape
Bulk
DLM11G
1.45
1.2
0.8 max.
-
10000
-
-
-
1000
DLM2HG
2.75
2.25
1.3
0.25
-
3000
-
-
1000
DLP0NS
0.95
0.75
0.55
0.25
-
5000
-
-
500
DLP11S
1.4
1.2
0.98
0.25
-
3000
-
-
500
DLP11T
1.35
1.1
0.45
0.25
-
5000
-
-
500
DLP1ND
1.7
0.84
0.57
0.25
-
5000
-
-
500
DLP2AD
2.2
1.2
0.98
0.25
-
3000
-
-
500
DLP31D/31S
3.5
1.9
1.3
0.25
-
3000
-
-
500
DLW21S
2.25
1.45
1.4
0.3
-
2000
-
-
500
DLW21H
2.3
1.55
1.1
0.25
-
3000
-
-
500
DLW31S
3.6
2.0
2.1
0.3
-
2000
-
-
500
b
c
0.4
Part Number
12.0
ø1.5 +0.1
-0
5.5±0.05
a
2.0±0.05
8.0±0.1
4.0±0.1
1.75±0.1
Minimum Quantity and Dimensions of 12mm Width Embossed Tape
Packaging
Chip Common Mode Choke Coil
(in mm)
Cavity Size
Minimum Qty. (pcs.)
ø180mm Reel ø330mm Reel
Bulk
a
b
c
DLW5AH
5.4
4.1
4.4
400
1500
100
DLW5BS
5.5
5.4
4.7
400
1500
100
DLW5BT
5.5
5.4
2.7
700
2500
100
Direction of feed
c: Depth of Cavity
(in mm)
Block Type EMIFILr
Dimension of the cavity is measured at the bottom side.
"Minimum Quantity" means the number of units of each delivery or order. The quantity should be an integral multiple of the "Minimum Quantity".
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
182
PL p
Chip Common Mode Choke Coil
Packaging
a
b
d
24.0±0.2
+0.1
ø1.5–0
11.75±0.1
2.0±0.1
1.75±0.1
4.0±0.1
Chip Ferrite Bead
Minimum Quantity and Dimensions of 24mm Width Embossed Tape
12.0±0.1
c
Direction of Feed
Part Number
Minimum Qty. (pcs.)
a
b
c
d
ø178mm Reel
ø330mm Reel
Bulk
13.5
6.5
9.4
0.5
125
500
50
Block Type EMIFILr
Packaging
Chip Common Mode Choke Coil
PLT10H
Cavity Size (mm)
Chip EMIFILr
(in mm)
Dimension of the cavity is measured at the bottom side.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
183
Chip Common Mode Choke Coil
Design Kits
Chip Ferrite Bead
DL p
Block Type EMIFILr
Design Kits Chip Common Mode Choke Coil
Chip EMIFILr
oEKEMDL21L (Chip Common Mode Choke Coils)
No.
Part Number
Quantity
(pcs.)
Common Mode Impedance
(at 100MHz, 20 degrees C)
Rated Voltage
(Vdc)
Rated Current
(mA)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
DLW21HN670SQ2
DLW21HN900SQ2
DLW21HN121SQ2
DLW21HN181SQ2
DLW21SN670SQ2
DLW21SN900SQ2
DLW21SN121SQ2
DLW21SN181SQ2
DLW21SN261SQ2
DLW21SN371SQ2
DLW21SN670HQ2
DLW21SN900HQ2
DLW21SN121HQ2
DLW21SR670HQ2
DLP0NSA150HL2
DLP0NSC280HL2
DLP0NSN670HL2
DLP0NSN900HL2
DLP0NSN121HL2
DLP1NDN350HL4
DLP1NDN670HL4
DLP1NDN900HL4
DLP11SA350HL2
DLP11SA670HL2
DLP11SA900HL2
DLP11SN670SL2
DLP11SN121SL2
DLP11SN161SL2
DLP11SN900HL2
DLP11SN201HL2
DLP11SN241HL2
DLP11SN281HL2
DLP11SN331HL2
DLP11TB800UL2
DLP2ADA350HL4
DLP2ADA670HL4
DLP2ADA900HL4
DLP2ADN670HL4
DLP2ADN900HL4
DLP2ADN121HL4
DLP2ADN161HL4
DLP2ADN201HL4
DLP2ADN241HL4
DLP2ADN281HL4
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
67Ω±25%
90Ω±25%
120Ω±25%
180Ω±25%
67Ω±25%
90Ω±25%
120Ω±25%
180Ω±25%
260Ω±25%
370Ω±25%
67Ω±25%
90Ω±25%
120Ω±25%
67Ω±25%
15Ω±5Ω
28Ω±20%
67Ω±20%
90Ω±20%
120Ω±20%
35Ω±20%
67Ω±20%
90Ω±20%
35Ω±20%
67Ω±20%
90Ω±20%
67Ω±20%
120Ω±20%
160Ω±20%
90Ω±20%
200Ω±20%
240Ω±20%
280Ω±20%
330Ω±20%
80Ω±25%
35Ω±20%
67Ω±20%
90Ω±20%
67Ω±20%
90Ω±20%
120Ω±20%
160Ω±20%
200Ω±20%
240Ω±20%
280Ω±20%
50
50
50
50
50
50
50
50
50
50
20
20
20
20
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
330
330
280
250
400
330
370
330
300
280
320
280
280
400
100
100
110
100
90
100
80
60
170
150
150
180
140
120
150
110
100
90
80
100
150
130
120
140
130
120
100
90
80
80
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
184
DLp Chip Common Mode Choke Coil Design Kits
Part Number
Quantity
(pcs.)
Common Mode Impedance
(at 100MHz, 20 degrees C)
Rated Voltage
(Vdc)
Rated Current
(mA)
1
2
3
4
5
6
7
8
9
10
11
DLW5AHN402SQ2
DLW5BSN191SQ2
DLW5BSN351SQ2
DLW5BSN102SQ2
DLW5BSN152SQ2
DLW5BSN302SQ2
DLW5BTN101SQ2
DLW5BTN251SQ2
DLW5BTN501SQ2
DLW5BTN102SQ2
DLW5BTN142SQ2
5
5
5
5
5
5
5
5
5
5
5
4000Ω (Typ.)
190Ω (Typ.)
350Ω (Typ.)
1000Ω (Typ.)
1500Ω (Typ.)
3000Ω (Typ.)
100Ω (Typ.)
250Ω (Typ.)
500Ω (Typ.)
1000Ω (Typ.)
1400Ω (Typ.)
50
50
50
50
50
50
50
50
50
50
50
200
5000
2000
1500
1000
500
6000
5000
4000
2000
1500
Block Type EMIFILr
Design Kits Chip Common Mode Choke Coil
Chip EMIFILr
No.
Chip Ferrite Bead
oEKEMDCC5C (Chip Common Mode Choke Coils for DC Power Line / SMD Block type EMIFILr for Power Line)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
185
Large Current Common Mode Choke Coils (Automotive Available)
Design Kits
Chip Ferrite Bead
PL p
oEKEPPL10B (Common Mode Choke Coil)
Part Number
Quantity
(pcs.)
Common Mode Impedance
(at 10MHz, 20 degrees C)
Rated Voltage
(Vdc)
Rated Current
(A)
1
2
3
4
PLT10HH401100PN
PLT10HH501100PN
PLT10HH9016R0PN
PLT10HH1026R0PN
6
6
6
6
400Ω (Typ.)
500Ω (Typ.)
900Ω (Typ.)
1000Ω (Typ.)
100
100
100
100
10
10
6
6
Block Type EMIFILr
Design Kits Chip Common Mode Choke Coil
Chip EMIFILr
No.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
C31E.pdf
Mar.28,2011
186
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Murata:
DLW5AHN402SQ2L DLW5BSN152SQ2L DLW5BSN191SQ2L DLW5BSN102SQ2L DLW5BSN302SQ2L
DLW21SN261SQ2L DLW5BSN351SQ2L DLP31SN221SL2B DLP31SN221SL2L DLP31SN121SL2L
DLP31DN441ML4L DLP31DN471SL4L DLW21HN670SQ2L DLW21SN670SQ2L DLW21SN181SQ2L
DLP11SN161SL2L DLW21HN181SQ2L DLP11SN201SL2L DLW31SN601SQ2L DLP31DN900SL4L
DLW21HN121SQ2L DLP31SN551SL2L DLW21SN261SQ2B DLW5BTN102SQ2L DLW5BTN142SQ2L
DLW5BTN251SQ2L DLW5BTN501SQ2L DLW5BSN102SQ2B DLP31SN221ML2B DLM2HGN601SZ3L
DLP11SN900SL2L DLW31SN900SQ2L DLP31DN900ML4L DLP0NSN900HL2L DLP2ADN121HL4L
DLP31SN221ML2L DLW31SN102SQ2L DLP31DN900SL4 DLW31SN222SQ2L DLW31SH222SQ2L
DLP31DN201ML4L DLW21SN121SQ2L DLW21SN371SQ2L DLP31DN131ML4L DLP31DN201SL4L
DLW21HN900SQ2L DLP11SN121SL2L DLP31DN321ML4L DLW21SN900SQ2L DLW31SN261SQ2L
DLW31SN161SQ2L DLP31DN161SL4L DLP31DN361SL4L DLP0NSN121HL2L DLP0NSN670HL2L
DLP11SA350HL2L DLP11SA670HL2L DLP11SA900HL2L DLP11SN241HL2L DLP11SN281HL2L
DLP11SN331HL2L DLP11SN900HL2L DLP2ADN161HL4L DLP2ADN201HL4L DLP2ADN241HL4L
DLP2ADN281HL4L DLP2ADN670HL4L DLP2ADN900HL4L DLW21SN121HQ2L DLW21SN670HQ2L
DLW21SR670HQ2L DLW43SH101XK2L DLW43SH510XK2B DLP11TB800UL2L DLW5BTN501SQ2K
DLW21SN900HQ2L DLW5BTN101SQ2L DLP31SN121ML2L DLP31SN551ML2L DLP11SN201HL2L
DLP11SN670SL2L DLP31DN441ML4B DLM11GN601SZ2D DLM11GN601SD2D DLW43SH101XP2L
DLW43SH110XK2L DLW43SH220XK2L
Similar pages