TI1 DP83630 Dp83630 precision phyter - ieeeâ® 1588 precision time protocol transceiver Datasheet

DP83630
DP83630 Precision PHYTER - IEEE® 1588 Precision Time Protocol Transceiver
Literature Number: SNLS335A
DP83630
Precision PHYTER - IEEE® 1588 Precision Time Protocol
Transceiver
1.0 General Description
3.0 Features
The DP83630 Precision PHYTER® device delivers the highest level of precision clock synchronization for real time industrial connectivity based on the IEEE 1588 standard. The
DP83630 has deterministic, low latency and allows choice of
microcontroller with no hardware customization required. The
integrated 1588 functionality allows system designers the
flexibility and precision of a close to the wire timestamp. The
three key 1588 features supported by the device are:
— Packet time stamps for clock synchronization
— Integrated IEEE 1588 synchronized low jitter clock generation
— Synchronized event triggering and time stamping through
GPIO
DP83630 offers innovative diagnostic features unique to National Semiconductor, including dynamic monitoring of link
quality during standard operation for fault prediction. These
advanced features allow the system designer to implement a
fault prediction mechanism to detect and warn of deteriorating
and changing link conditions. This single port fast Ethernet
transceiver can support both copper and fiber media.
■ IEEE 1588 V1 and V2 supported
■ UDP/IPv4, UDP/IPv6, and Layer2 Ethernet packets
2.0 Applications
■ Telecom
■
■
■
■
— Basestation
— Pico/Femto Cells
Factory Automation
— Ethernet/IP
— CIP Sync
Test and Measurement
— LXI Standard
Video Synchronization
Real Time Networking
supported
IEEE 1588 clock synchronization
Selectable frequency synchronized low jitter clock output
Timestamp resolution of 8 ns
Allows sub 10 ns synchronization to master reference
12 IEEE 1588 GPIOs for trigger or capture
Deterministic, low transmit and receive latency
Dynamic Link Quality monitoring
TDR based Cable Diagnostic and Cable Length Detection
10/100 Mb/s packet BIST (Built in Self Test)
Error-free Operation up to 150 meters CAT5 cable
ESD protection - 8 kV human body model
2.5 V and 3.3 V I/Os and MAC interface
Auto-MDIX for 10/100 Mbps
Auto-crossover in forced modes of operation
RMII Rev. 1.2 and MII MAC interface
RMII Master mode
25 MHz MDC and MDIO Serial Management Interface
IEEE 802.3u 100BASE-FX Fiber Interface
IEEE 1149.1 JTAG
Programmable LED support for Link, 10 /100 Mb/s Mode,
Duplex, Activity, and Collision Detect
■ Optional 100BASE-TX fast link-loss detection
■ Industrial temperature range
■ 48 pin LLP package (7mm) x (7mm)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4.0 System Diagram
30136217
PHYTER® is a registered trademark of National Semiconductor.
© 2011 National Semiconductor Corporation
301362
www.national.com
DP83630 Precision PHYTER - IEEE 1588 Precision Time Protocol Transceiver
February 23, 2011
DP83630
Table of Contents
1.0 General Description ......................................................................................................................... 1
2.0 Applications .................................................................................................................................... 1
3.0 Features ........................................................................................................................................ 1
4.0 System Diagram .............................................................................................................................. 1
5.0 Block Diagram ................................................................................................................................ 6
6.0 Key IEEE 1588 Features .................................................................................................................. 6
6.1 IEEE 1588 SYNCHRONIZED CLOCK ......................................................................................... 7
6.1.1 IEEE 1588 Clock Output .................................................................................................. 7
6.1.2 IEEE 1588 Clock Input .................................................................................................... 8
6.2 PACKET TIMESTAMPS ........................................................................................................... 8
6.2.1 IEEE 1588 Transmit Packet Parser and Timestamp ............................................................ 8
6.2.1.1 One-Step Operation .............................................................................................. 8
6.2.2 IEEE 1588 Receive Packet Parser and Timestamp ............................................................. 8
6.2.2.1 Receive Timestamp Insertion ................................................................................. 8
6.2.3 NTP Packet Timestamp .................................................................................................. 8
6.3 EVENT TRIGGERING AND TIMESTAMPING .............................................................................. 8
6.3.1 IEEE 1588 Event Triggering ............................................................................................. 8
6.3.2 IEEE 1588 Event Timestamping ....................................................................................... 8
6.4 PTP INTERRUPTS .................................................................................................................. 8
6.5 GPIO ...................................................................................................................................... 8
7.0 Pin Layout ...................................................................................................................................... 9
8.0 Pin Descriptions ............................................................................................................................ 10
8.1 SERIAL MANAGEMENT INTERFACE ...................................................................................... 10
8.2 MAC DATA INTERFACE ......................................................................................................... 10
8.3 CLOCK INTERFACE .............................................................................................................. 12
8.4 LED INTERFACE ................................................................................................................... 13
8.5 IEEE 1588 EVENT/TRIGGER/CLOCK INTERFACE ................................................................... 13
8.6 JTAG INTERFACE ................................................................................................................. 13
8.7 RESET AND POWER DOWN .................................................................................................. 14
8.8 STRAP OPTIONS .................................................................................................................. 15
8.9 10 Mb/s AND 100 Mb/s PMD INTERFACE ................................................................................ 16
8.10 POWER SUPPLY PINS ........................................................................................................ 17
8.11 PACKAGE PIN ASSIGNMENTS ............................................................................................. 17
9.0 Configuration ................................................................................................................................ 18
9.1 MEDIA CONFIGURATION ...................................................................................................... 18
9.2 AUTO-NEGOTIATION ............................................................................................................ 18
9.2.1 Auto-Negotiation Pin Control .......................................................................................... 18
9.2.2 Auto-Negotiation Register Control ................................................................................... 18
9.2.3 Auto-Negotiation Parallel Detection ................................................................................. 19
9.2.4 Auto-Negotiation Restart ............................................................................................... 19
9.2.5 Enabling Auto-Negotiation via Software ........................................................................... 19
9.2.6 Auto-Negotiation Complete Time .................................................................................... 19
9.3 AUTO-MDIX .......................................................................................................................... 19
9.4 AUTO-CROSSOVER IN FORCED MODE ................................................................................. 19
9.5 PHY ADDRESS ..................................................................................................................... 19
9.5.1 MII Isolate Mode ........................................................................................................... 20
9.5.2 Broadcast Mode ........................................................................................................... 20
9.6 LED INTERFACE ................................................................................................................... 20
9.6.1 LEDs .......................................................................................................................... 21
9.6.2 LED Direct Control ........................................................................................................ 21
9.7 HALF DUPLEX vs. FULL DUPLEX ........................................................................................... 21
9.8 INTERNAL LOOPBACK .......................................................................................................... 22
9.9 POWER DOWN/INTERRUPT .................................................................................................. 22
9.9.1 Power Down Control Mode ............................................................................................ 22
9.9.2 Interrupt Mechanisms ................................................................................................... 22
9.10 ENERGY DETECT MODE ..................................................................................................... 22
9.11 LINK DIAGNOSTIC CAPABILITIES ........................................................................................ 22
9.11.1 Linked Cable Status .................................................................................................... 22
9.11.1.1 Polarity Reversal .............................................................................................. 22
9.11.1.2 Cable Swap Indication ....................................................................................... 22
9.11.1.3 100 Mb Cable Length Estimation ........................................................................ 22
9.11.1.4 Frequency Offset Relative to Link Partner ............................................................ 22
9.11.1.5 Cable Signal Quality Estimation .......................................................................... 23
9.11.2 Link Quality Monitor .................................................................................................... 23
www.national.com
2
3
23
23
23
24
24
24
24
24
24
25
25
25
25
25
25
26
26
26
26
26
26
27
27
28
28
28
30
30
31
31
31
31
31
32
32
32
33
33
33
33
33
33
33
33
33
33
33
33
34
34
34
34
34
35
35
35
35
35
35
35
35
35
35
35
36
36
www.national.com
DP83630
9.11.2.1 Link Quality Monitor Control and Status ...............................................................
9.11.2.2 Checking Current Parameter Values ....................................................................
9.11.2.3 Threshold Control .............................................................................................
9.11.3 TDR Cable Diagnostics ...............................................................................................
9.11.4 TDR Pulse Generator ..................................................................................................
9.11.5 TDR Pulse Monitor .....................................................................................................
9.11.6 TDR Control Interface .................................................................................................
9.11.7 TDR Results ..............................................................................................................
9.12 BIST ...................................................................................................................................
10.0 MAC Interface .............................................................................................................................
10.1 MII INTERFACE ...................................................................................................................
10.1.1 Nibble-wide MII Data Interface ......................................................................................
10.1.2 Collision Detect ..........................................................................................................
10.1.3 Carrier Sense .............................................................................................................
10.2 REDUCED MII INTERFACE ..................................................................................................
10.2.1 RMII Master Mode ......................................................................................................
10.2.2 RMII Slave Mode ........................................................................................................
10.3 SINGLE CLOCK MII MODE ...................................................................................................
10.4 IEEE 802.3u MII SERIAL MANAGEMENT INTERFACE ............................................................
10.4.1 Serial Management Register Access .............................................................................
10.4.2 Serial Management Access Protocol .............................................................................
10.4.3 Serial Management Preamble Suppression ....................................................................
10.5 PHY CONTROL FRAMES .....................................................................................................
10.6 PHY STATUS FRAMES ........................................................................................................
11.0 Architecture ................................................................................................................................
11.1 100BASE-TX TRANSMITTER ................................................................................................
11.1.1 Code-Group Encoding and Injection ..............................................................................
11.1.2 Scrambler ..................................................................................................................
11.1.3 NRZ to NRZI Encoder .................................................................................................
11.1.4 Binary to MLT-3 Convertor ...........................................................................................
11.2 100BASE-TX RECEIVER ......................................................................................................
11.2.1 Analog Front End ........................................................................................................
11.2.2 Digital Signal Processor ...............................................................................................
11.2.2.1 Base Line Wander Compensation .......................................................................
11.2.2.2 Digital Adaptive Equalization and Gain Control .....................................................
11.2.3 Signal Detect .............................................................................................................
11.2.4 MLT-3 to Binary Decoder .............................................................................................
11.2.5 Clock Recovery Module ...............................................................................................
11.2.6 NRZI to NRZ Decoder .................................................................................................
11.2.7 Serial to Parallel .........................................................................................................
11.2.8 Descrambler ..............................................................................................................
11.2.9 Code-Group Alignment ................................................................................................
11.2.10 4B/5B Decoder .........................................................................................................
11.2.11 100BASE-TX Link Integrity Monitor .............................................................................
11.2.12 Bad SSD Detection ...................................................................................................
11.3 100BASE-FX OPERATION ....................................................................................................
11.3.1 100BASE-FX Transmit ................................................................................................
11.3.2 100BASE-FX Receive .................................................................................................
11.3.3 Far-End Fault .............................................................................................................
11.4 10BASE-T TRANSCEIVER MODULE .....................................................................................
11.4.1 Operational Modes .....................................................................................................
11.4.2 Smart Squelch ...........................................................................................................
11.4.3 Collision Detection and SQE ........................................................................................
11.4.4 Carrier Sense .............................................................................................................
11.4.5 Normal Link Pulse Detection/Generation ........................................................................
11.4.6 Jabber Function .........................................................................................................
11.4.7 Automatic Link Polarity Detection and Correction ............................................................
11.4.8 Transmit and Receive Filtering .....................................................................................
11.4.9 Transmitter ................................................................................................................
11.4.10 Receiver ..................................................................................................................
12.0 Reset Operation ..........................................................................................................................
12.1 HARDWARE RESET ............................................................................................................
12.2 FULL SOFTWARE RESET ....................................................................................................
12.3 SOFT RESET ......................................................................................................................
12.4 PTP RESET ........................................................................................................................
13.0 Design Guidelines .......................................................................................................................
DP83630
13.1 TPI NETWORK CIRCUIT ......................................................................................................
13.2 FIBER NETWORK CIRCUIT ..................................................................................................
13.3 ESD PROTECTION ..............................................................................................................
13.4 CLOCK IN (X1) RECOMMENDATIONS ..................................................................................
14.0 Register Block .............................................................................................................................
14.1 REGISTER DEFINITION .......................................................................................................
14.1.1 Basic Mode Control Register (BMCR) ............................................................................
14.1.2 Basic Mode Status Register (BMSR) .............................................................................
14.1.3 PHY Identifier Register #1 (PHYIDR1) ...........................................................................
14.1.4 PHY Identifier Register #2 (PHYIDR2) ...........................................................................
14.1.5 Auto-Negotiation Advertisement Register (ANAR) ...........................................................
14.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page) .............................
14.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page) ...............................
14.1.8 Auto-Negotiate Expansion Register (ANER) ...................................................................
14.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR) ...............................................
14.1.10 PHY Status Register (PHYSTS) ..................................................................................
14.1.11 MII Interrupt Control Register (MICR) ...........................................................................
14.1.12 MII Interrupt Status and Event Control Register (MISR) ..................................................
14.1.13 Page Select Register (PAGESEL) ...............................................................................
14.2 EXTENDED REGISTERS - PAGE 0 .......................................................................................
14.2.1 False Carrier Sense Counter Register (FCSCR) .............................................................
14.2.2 Receiver Error Counter Register (RECR) .......................................................................
14.2.3 100 Mb/s PCS Configuration and Status Register (PCSR) ................................................
14.2.4 RMII and Bypass Register (RBR) ..................................................................................
14.2.5 LED Direct Control Register (LEDCR) ...........................................................................
14.2.6 PHY Control Register (PHYCR) ....................................................................................
14.2.7 10Base-T Status/Control Register (10BTSCR) ................................................................
14.2.8 CD Test and BIST Extensions Register (CDCTRL1) ........................................................
14.2.9 PHY Control Register 2 (PHYCR2) ...............................................................................
14.2.10 Energy Detect Control (EDCR) ...................................................................................
14.2.11 PHY Control Frames Configuration Register (PCFCR) ...................................................
14.3 TEST REGISTERS - PAGE 1 ................................................................................................
14.3.1 Signal Detect Configuration (SD_CNFG), Page 1 ............................................................
14.4 LINK DIAGNOSTICS REGISTERS - PAGE 2 ...........................................................................
14.4.1 100 Mb Length Detect Register (LEN100_DET), Page 2 ..................................................
14.4.2 100 Mb Frequency Offset Indication Register (FREQ100), Page 2 .....................................
14.4.3 TDR Control Register (TDR_CTRL), Page 2 ...................................................................
14.4.4 TDR Window Register (TDR_WIN), Page 2 ....................................................................
14.4.5 TDR Peak Register (TDR_PEAK), Page 2 .....................................................................
14.4.6 TDR Threshold Register (TDR_THR), Page 2 .................................................................
14.4.7 Variance Control Register (VAR_CTRL), Page 2 .............................................................
14.4.8 Variance Data Register (VAR_DATA), Page 2 ................................................................
14.4.9 Link Quality Monitor Register (LQMR), Page 2 ................................................................
14.4.10 Link Quality Data Register (LQDR), Page 2 ..................................................................
14.4.11 Link Quality Monitor Register 2 (LQMR2), Page 2 .........................................................
14.5 PTP 1588 BASE REGISTERS - PAGE 4 .................................................................................
14.5.1 PTP Control Register (PTP_CTL), Page 4 ......................................................................
14.5.2 PTP Time Data Register (PTP_TDR), Page 4 .................................................................
14.5.3 PTP Status Register (PTP_STS), Page 4 .......................................................................
14.5.4 PTP Trigger Status Register (PTP_TSTS), Page 4 ..........................................................
14.5.5 PTP Rate Low Register (PTP_RATEL), Page 4 ..............................................................
14.5.6 PTP Rate High Register (PTP_RATEH), Page 4 .............................................................
14.5.7 PTP Read Checksum (PTP_RDCKSUM), Page 4 ...........................................................
14.5.8 PTP Write Checksum (PTP_WRCKSUM), Page 4 ...........................................................
14.5.9 PTP Transmit Timestamp Register (PTP_TXTS), Page 4 .................................................
14.5.10 PTP Receive Timestamp Register (PTP_RXTS), Page 4 ................................................
14.5.11 PTP Event Status Register (PTP_ESTS), Page 4 ..........................................................
14.5.12 PTP Event Data Register (PTP_EDATA), Page 4 ..........................................................
14.6 PTP 1588 CONFIGURATION REGISTERS - PAGE 5 ...............................................................
14.6.1 PTP Trigger Configuration Register (PTP_TRIG), Page 5 .................................................
14.6.2 PTP Event Configuration Register (PTP_EVNT), Page 5 ..................................................
14.6.3 PTP Transmit Configuration Register 0 (PTP_TXCFG0), Page 5 .......................................
14.6.4 PTP Transmit Configuration Register 1 (PTP_TXCFG1), Page 5 .......................................
14.6.5 PHY Status Frame Configuration Register 0 (PSF_CFG0), Page 5 ....................................
14.6.6 PTP Receive Configuration Register 0 (PTP_RXCFG0), Page 5, ......................................
14.6.7 PTP Receive Configuration Register 1 (PTP_RXCFG1), Page 5 .......................................
www.national.com
4
36
37
37
37
39
45
46
48
49
49
50
51
52
52
53
54
56
57
59
59
59
59
60
62
63
64
66
67
68
69
70
71
71
72
72
72
73
74
74
74
75
75
76
78
79
80
80
82
82
83
84
85
85
85
86
86
87
88
90
90
91
92
93
93
94
95
5
www.national.com
DP83630
14.6.8 PTP Receive Configuration Register 2 (PTP_RXCFG2), Page 5 ....................................... 95
14.6.9 PTP Receive Configuration Register 3 (PTP_RXCFG3), Page 5 ....................................... 96
14.6.10 PTP Receive Configuration Register 4 (PTP_RXCFG4), Page 5 ..................................... 97
14.6.11 PTP Temporary Rate Duration Low Register (PTP_TRDL), Page 5 ................................. 97
14.6.12 PTP Temporary Rate Duration High Register (PTP_TRDH), Page 5 ................................ 98
14.7 PTP 1588 CONFIGURATION REGISTERS - PAGE 6 ............................................................... 98
14.7.1 PTP Clock Output Control Register (PTP_COC), Page 6 ................................................. 98
14.7.2 PHY Status Frame Configuration Register 1 (PSF_CFG1), Page 6 .................................... 99
14.7.3 PHY Status Frame Configuration Register 2 (PSF_CFG2), Page 6 .................................... 99
14.7.4 PHY Status Frame Configuration Register 3 (PSF_CFG3), Page 6 .................................... 99
14.7.5 PHY Status Frame Configuration Register 4 (PSF_CFG4), Page 6 .................................... 99
14.7.6 PTP SFD Configuration Register (PTP_SFDCFG), Page 6 ............................................. 100
14.7.7 PTP Interrupt Control Register (PTP_INTCTL), Page 6 .................................................. 100
14.7.8 PTP Clock Source Register (PTP_CLKSRC), Page 6 .................................................... 100
14.7.9 PTP Ethernet Type Register (PTP_ETR), Page 6 .......................................................... 100
14.7.10 PTP Offset Register (PTP_OFF), Page 6 ................................................................... 101
14.7.11 PTP GPIO Monitor Register (PTP_GPIOMON), Page 6 ............................................... 101
14.7.12 PTP Receive Hash Register (PTP_RXHASH), Page 6 ................................................. 101
15.0 Absolute Maximum Ratings ......................................................................................................... 102
16.0 Recommended Operating Conditions ........................................................................................... 102
17.0 Thermal Characteristic ............................................................................................................... 102
18.0 AC and DC Specifications ........................................................................................................... 102
18.1 DC SPECIFICATIONS ........................................................................................................ 102
18.2 AC SPECIFICATIONS ........................................................................................................ 104
18.2.1 Power Up Timing ...................................................................................................... 104
18.2.2 Reset Timing ........................................................................................................... 105
18.2.3 MII Serial Management Timing ................................................................................... 106
18.2.4 100 Mb/s MII Transmit Timing .................................................................................... 106
18.2.5 100 Mb/s MII Receive Timing ..................................................................................... 107
18.2.6 100BASE-TX and 100BASE-FX MII Transmit Packet Latency Timing .............................. 107
18.2.7 100BASE-TX and 100BASE-FX MII Transmit Packet Deassertion Timing ........................ 108
18.2.8 100BASE-TX Transmit Timing (tR/F & Jitter) .................................................................. 108
18.2.9 100BASE-TX and 100BASE-FX MII Receive Packet Latency Timing ............................... 109
18.2.10 100BASE-TX and 100BASE-FX MII Receive Packet Deassertion Timing ....................... 109
18.2.11 10 Mb/s MII Transmit Timing .................................................................................... 110
18.2.12 10 Mb/s MII Receive Timing ..................................................................................... 110
18.2.13 10BASE-T MII Transmit Timing (Start of Packet) ......................................................... 111
18.2.14 10BASE-T MII Transmit Timing (End of Packet) .......................................................... 111
18.2.15 10BASE-T MII Receive Timing (Start of Packet) .......................................................... 112
18.2.16 10BASE-T MII Receive Timing (End of Packet) ........................................................... 112
18.2.17 10 Mb/s Heartbeat Timing ....................................................................................... 113
18.2.18 10 Mb/s Jabber Timing ........................................................................................... 113
18.2.19 10BASE-T Normal Link Pulse Timing ......................................................................... 114
18.2.20 Auto-Negotiation Fast Link Pulse (FLP) Timing ........................................................... 114
18.2.21 100BASE-TX Signal Detect Timing ........................................................................... 115
18.2.22 100 Mb/s Internal Loopback Timing .......................................................................... 115
18.2.23 10 Mb/s Internal Loopback Timing ............................................................................ 116
18.2.24 RMII Transmit Timing (Slave Mode) .......................................................................... 116
18.2.25 RMII Transmit Timing (Master Mode) ......................................................................... 117
18.2.26 RMII Receive Timing (Slave Mode) ........................................................................... 118
18.2.27 RMII Receive Timing (Master Mode) .......................................................................... 119
18.2.28 RX_CLK Timing (RMII Master Mode) ......................................................................... 120
18.2.29 CLK_OUT Timing (RMII Slave Mode) ........................................................................ 120
18.2.30 Single Clock MII (SCMII) Transmit Timing ................................................................. 121
18.2.31 Single Clock MII (SCMII) Receive Timing ................................................................... 122
18.2.32 100 Mb/s X1 to TX_CLK Timing ................................................................................ 123
19.0 Physical Dimensions .................................................................................................................. 124
20.0 Ordering Information .................................................................................................................. 124
DP83630
5.0 Block Diagram
30136218
DP83630 Functional Block Diagarm
The DP83630 provides features for controlling the clock operation in Slave mode. The clock value can be updated to
match the Master clock in several ways. In addition, the clock
can be programmed to adjust its frequency to compensate for
drift.
The DP83630 supports real time triggering activities and captures real time events to report to the microcontroller. Controlled devices can be connected to the DP83630 through the
available GPIO.
The IEEE 1588 features are briefly presented below. For a
more detailed discussion on configuring the IEEE 1588
features, refer to the Software Development Guide for the
DP83630.
6.0 Key IEEE 1588 Features
IEEE 1588 provides a time synchronization protocol, often
referred to as the Precision Time Protocol (PTP), which synchronizes time across an Ethernet network. DP83630 supports IEEE 1588 Real Time Ethernet applications by providing
hardware support for three time critical elements.
• IEEE 1588 synchronized clock generation
• Packet timestamps for clock synchronization
• Event triggering and timestamping through GPIO
By combining the above capabilities, the DP83630 provides
advanced and flexible support for IEEE 1588 for use in a
highly accurate IEEE 1588 system.
www.national.com
6
DP83630
30136252
FIGURE 1. DP83630 Example System Application
therefore require a step adjustment or a direct time set. Later,
when clocks are very close in value, the temporary rate adjustment method may be the best option.
The clock does not support negative time values. If negative
time is required in the system, software will have to make
conversions from the PHY clock time to actual time.
The clock also does not support the upper 16-bits of the seconds field as defined by the specification (Version 2 specifies
a 48-bit seconds field). If this value is required to be greater
than 0, it will have to be handled by software. Since a rollover
of the seconds field only occurs every 136 years, it should not
be a significant burden to software.
6.1 IEEE 1588 SYNCHRONIZED CLOCK
The DP83630 provides several mechanisms for updating the
IEEE 1588 clock based on the synchronization protocol required. These methods are listed below.
• Directly Read/Writable
• Adjustable by Add/Subtract
• Frequency Scalable
• Temporary Frequency Control
The clock consists of the following fields: Seconds (32–bit
field), Nanoseconds (30–bit field), and Fractional Nanoseconds (units of 2-32 ns).
A direct set of the time value can be done by setting a new
time value. A step adjustment value in nanoseconds may be
added to the current value. Note that the adjustment value
can be positive or negative.
The clock can be programmed to operate at an adjusted frequency value by programming a rate adjustment value. The
clock can also be programmed to perform a temporary adjusted frequency value by including a rate adjustment duration. The rate adjustment allows for correction on the order of
2-32 ns per reference clock cycle. The frequency adjustment
will allow the clock to correct the offset over time, avoiding any
potential side-effects caused by a step adjustment in the time
value.
The method used to update the clock value may depend on
the difference in the values. For example, at the initial synchronization attempt, the clocks may be very far apart, and
6.1.1 IEEE 1588 Clock Output
The DP83630 provides for a synchronized clock signal for use
by external devices. The output clock signal can be any frequency generated from 250 MHz divided by n, where n is an
integer in the range of 2 to 255. This provides nominal frequencies from 125 MHz down to 980.4 kHz. The clock output
signal is controlled by the PTP_COC register. The output
clock signal is generated using the rate information in the
PTP_RATE registers and is therefore frequency accurate to
the 1588 clock time of the device. In addition, if clock time
adjustments are made using the Temporary Rate capabilities,
then all time adjustments will be tracked by the output clock
signal as well. Note that any step adjustment in the 1588 clock
time will not be accurately represented on the 1588 clock output signal.
7
www.national.com
DP83630
ured to timestamp both PTP and NTP packets). One-Step
operation is not supported for NTP timestamps, so transmit
timestamps cannot be inserted directly into outgoing NTP
packets. Timestamp insertion is available for receive timestamps but must use a single, fixed location.
6.1.2 IEEE 1588 Clock Input
The IEEE 1588 PTP logic operates on a nominal 125 MHz
reference clock generated by an internal Phase Generation
Module (PGM). However, options are available to use a divided-down version of the PGM clock to reduce power consumption at the expense of precision, or to use an external
reference clock of up to 125 MHz in the event the 1588 clock
is tracked externally.
6.3 EVENT TRIGGERING AND TIMESTAMPING
6.3.1 IEEE 1588 Event Triggering
The DP83630 is capable of being programmed to generate a
trigger signal on an output pin based on the IEEE 1588 time
value. Each trigger can be programmed to generate a onetime rising or falling edge, a single pulse of programmable
width, or a periodic signal.
For each trigger, the microcontroller specifies the desired
GPIO and time that the activity is to occur. The trigger is generated when the internal IEEE 1588 clock matches the desired activation time.
The device supports up to 8 trigger signals which can be output on any of the GPIO signal pins. Multiple triggers may be
assigned to a single GPIO, allowing generation of more complex waveforms (i.e. a sequence of varying width pulses). The
trigger signals are OR’ed together to form a combined signal.
The triggers are configured through the PTP Trigger Configuration Registers. The trigger time and width settings are
controlled through the PTP Control and Time Data registers.
The DP83630 can be programmed to output a Pulse-PerSecond (PPS) signal using the trigger functions.
6.2 PACKET TIMESTAMPS
6.2.1 IEEE 1588 Transmit Packet Parser and Timestamp
The IEEE 1588 transmit parser monitors transmit packet data
to detect IEEE 1588 Version 1 and Version 2 Event messages. The transmit parser can detect PTP Event messages
transported directly in Layer2 Ethernet packets as well as in
UDP/IPv4 and UDP/IPv6 packets. Upon detection of a PTP
Event Message, the device will capture the transmit timestamp and provide it to software.
Since software knows the order of packet transmission, only
the timestamp is recorded (there is no need to record sequence number or other information). The device can buffer
four timestamps.
If enabled, an interrupt may be generated upon a Transmit
Timestamp Ready.
6.2.1.1 One-Step Operation
In some cases, the transmitter can be set to operate in a OneStep mode. For Sync Messages, a One-Step device can
automatically insert timestamp information in the outgoing
packet. This eliminates the need for software to read the
timestamp and send a follow up message.
6.3.2 IEEE 1588 Event Timestamping
The DP83630 can be programmed to timestamp an event by
monitoring an input signal. The event can be monitored for
rising edge, falling edge, or either. The Event Timestamp Unit
can monitor up to eight events which can be set to any of the
GPIO signal pins. PTP event timestamps are stored in a
queue which allows storage of up to eight timestamps.
When an event timestamp is available, the device will set the
EVENT_RDY bit in the PTP Status Register. The PTP Event
Status Register (PTP_ESTS) provides detailed information
on the next available event timestamp, including information
on the event number, rise/fall direction, and indication of
events missed due to overflow of the devices Event queue.
Event timestamp values should be adjusted by 35 ns (3 times
period of the IEEE 1588 reference clock frequency of 125
MHz + 11 ns) to compensate for input path and synchronization delays.
The Event Timestamp Unit is configured through the PTP
Event Configuration Register (PTP_EVNT).
6.2.2 IEEE 1588 Receive Packet Parser and Timestamp
The IEEE 1588 receive parser monitors receive packet data
to detect IEEE 1588 Version 1 and Version 2 Event messages. The receive parser can detect PTP Event messages
transported directly in Ethernet packets as well as in UDP/
IPv4 and UDP/IPv6 packets. Upon detection of a PTP Event
message, the device will capture the receive timestamp and
provide the timestamp value to software. In addition to the
timestamp, the device will record the 16-bit SequenceId, the
4-bit messageType field, and generate a 12-bit hash value for
octets 20-29 of the PTP event message. The device can
buffer four timestamps.
An interrupt will be generated, if enabled, upon a Receive
Timestamp Ready.
6.2.2.1 Receive Timestamp Insertion
The DP83630 can deliver the timestamp to software by inserting the timestamp in the received packet. This allows for
a simple method to deliver the packet to software without
having to match the timestamp to the correct packet. This also
eliminates the need to read the receive timestamp through the
Serial Management Interface.
6.4 PTP INTERRUPTS
The PTP module may interrupt the system using the PWRDOWN/INTN pin on the device, shared with other interrupts
from the PHY. As an alternative, the device may be programmed to use a GPIO pin to generate PTP interrupts
separate from other PHY interrupts.
6.2.3 NTP Packet Timestamp
The DP83630 may be programmed to timestamp NTP packets instead of PTP packets. This operation is enabled by
setting the NTP_TS_EN control in the PTP_TXCFG0 register.
When configured for NTP timestamps, the DP83630 will
timestamp packets with the NTP UDP port number rather than
the PTP port number (note that the device cannot be config-
www.national.com
6.5 GPIO
The DP83630 features 12 IEEE 1588 GPIO pins. These GPIO
pins allow for event monitoring, triggering, interrupts, and a
clock output. The LED pins comprise 3 of the 12 GPIO pins.
If an LED pin is to be used as a GPIO, its LED function must
be disabled prior to configuring the GPIO function.
8
DP83630
7.0 Pin Layout
30136259
Top View
Order Number DP83630SQ
NS Package Number SQA48A
9
www.national.com
DP83630
All DP83630 signal pins are I/O cells regardless of the particular use. The definitions below define the functionality of
the I/O cells for each pin.
8.0 Pin Descriptions
The DP83630 pins are classified into the following interface
categories (each interface is described in the sections that
follow):
• Serial Management Interface
• MAC Data Interface
• Clock Interface
• LED Interface
• GPIO Interface
• JTAG Interface
• Reset and Power Down
• Strap Options
• 10/100 Mb/s PMD Interface
• Power and Ground pins
Type: I
Type: O
Type: I/O
Type: OD
Type: PD
Type: PU
Type: S
Note: Strapping pin option. Please see Section Section 8.8 STRAP OPTIONSfor strap definitions.
Input
Output
Input/Output
Open Drain
Internal Pulldown
Internal Pullup
Strapping Pin (All strap pins have weak
internal pull-ups or pull-downs. If the default
strap value is to be changed then an external
2.2 kΩ resistor should be used. Please see
Section Section 8.8 STRAP OPTIONS for
details.)
8.1 SERIAL MANAGEMENT INTERFACE
Signal Name
Pin Name
Type
Pin #
Description
MDC
MDC
I
31
MANAGEMENT DATA CLOCK: Synchronous clock to the MDIO
management data input/output serial interface which may be
asynchronous to transmit and receive clocks. The maximum clock rate is
25 MHz with no minimum clock rate.
MDIO
MDIO
I/O
30
MANAGEMENT DATA I/O: Bi-directional management instruction/data
signal that may be sourced by the station management entity or the PHY.
This pin requires a 1.5 kΩ pullup resistor. Alternately, an internal pullup
may be enabled by setting bit 3 in the CDCTRL1 register.
8.2 MAC DATA INTERFACE
Type
Pin #
Description
TX_CLK
Signal Name
TX_CLK
O
1
MII TRANSMIT CLOCK: 25 MHz Transmit clock output in 100 Mb/s mode
or 2.5 MHz in 10 Mb/s mode derived from the 25 MHz reference clock.
The MAC should source TX_EN and TXD[3:0] using this clock.
RMII MODE: Unused in RMII Slave mode. The device uses the X1
reference clock input as the 50 MHz reference for both transmit and
receive. For RMII Master mode, the device outputs the internally
generated 50 MHz reference clock on this pin.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
TX_EN
TX_EN
I, PD
2
MII TRANSMIT ENABLE: Active high input indicates the presence of
valid data inputs on TXD[3:0].
RMII TRANSMIT ENABLE: Active high input indicates the presence of
valid data on TXD[1:0].
TXD_0
TXD_1
TXD_2
TXD_3
TXD_0
TXD_1
TXD_2
TXD_3
I
I
I
I, PD
3
4
5
6
MII TRANSMIT DATA: Transmit data MII input pins, TXD[3:0], that
accept data synchronous to the TX_CLK (2.5 MHz in 10 Mb/s mode or
25 MHz in 100 Mb/s mode).
RMII TRANSMIT DATA: Transmit data RMII input pins, TXD[1:0], that
accept data synchronous to the 50 MHz reference clock.
RX_CLK
RX_CLK
O
38
MII RECEIVE CLOCK: Provides the 25 MHz recovered receive clocks
for 100 Mb/s mode and 2.5 MHz for 10 Mb/s mode.
RMII MODE: Unused in RMII Slave mode. The device uses the X1
reference clock input as the 50 MHz reference for both transmit and
receive. For RMII Master mode, the device outputs the internally
generated 50 MHz reference clock on this pin.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
www.national.com
Pin Name
10
Pin Name
Type
Pin #
Description
RX_DV
RX_DV
O, PD
39
MII RECEIVE DATA VALID: Asserted high to indicate that valid data is
present on the corresponding RXD[3:0].
RMII RECEIVE DATA VALID: This signal provides the RMII Receive
Data Valid indication independent of Carrier Sense.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
RX_ER
RX_ER
S, O, PU
41
MII RECEIVE ERROR: Asserted high synchronously to RX_CLK to
indicate that an invalid symbol has been detected within a received packet
in 100 Mb/s mode.
RMII RECEIVE ERROR: Asserted high synchronously to X1 whenever a
media error is detected, and RX_DV is asserted in 100 Mb/s mode.
This pin is not required to be used by a MAC in RMII mode, since the PHY
is required to corrupt data on a receive error.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
RXD_0
RXD_1
RXD_2
RXD_3
RXD_0
RXD_1
RXD_2
RXD_3
S, O, PD
46
45
44
43
MII RECEIVE DATA: Nibble wide receive data signals driven
synchronously to the RX_CLK (25 MHz for 100 Mb/s mode, 2.5 MHz for
10 Mb/s mode). RXD[3:0] signals contain valid data when RX_DV is
asserted.
RMII RECEIVE DATA: 2-bits receive data signals, RXD[1:0], driven
synchronously to the 50 MHz reference clock.
These pins provide integrated 50 ohm signal terminations, making
external termination resistors unnecessary.
CRS/CRS_DV
CRS/CRS_DV
S, O, PU
40
MII CARRIER SENSE: Asserted high to indicate the receive medium is
non-idle.
RMII CARRIER SENSE/RECEIVE DATA VALID: This signal combines
the RMII Carrier and Receive Data Valid indications. For a detailed
description of this signal, see the RMII Specification.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
COL
COL
S, O, PU
42
MII COLLISION DETECT: Asserted high to indicate detection of a
collision condition (simultaneous transmit and receive activity) in 10 Mb/
s and 100 Mb/s Half Duplex Modes.
While in 10BASE-T Half Duplex mode with heartbeat enabled this pin is
also asserted for a duration of approximately 1µs at the end of
transmission to indicate heartbeat (SQE test).
In Full Duplex Mode, for 10 Mb/s or 100 Mb/s operation, this signal is
always logic 0. There is no heartbeat function during 10 Mb/s full duplex
operation.
RMII COLLISION DETECT: Per the RMII Specification, no COL signal is
required. The MAC will recover CRS from the CRS_DV signal and use
that along with its TX_EN signal to determine collision.
This pin provides an integrated 50 ohm signal termination, making
external termination resistors unnecessary.
11
www.national.com
DP83630
Signal Name
DP83630
8.3 CLOCK INTERFACE
Signal Name
Pin Name
Type
Pin #
Description
X1
X1
I
34
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock reference
input for the DP83630 and must be connected to a 25 MHz 0.005% (±50
ppm) clock source. The DP83630 supports either an external crystal
resonator connected across pins X1 and X2 or an external CMOS-level
oscillator source connected to pin X1 only.
RMII REFERENCE CLOCK: For RMII Slave Mode, this pin must be
connected to a 50 MHz 0.005% (±50 ppm) CMOS-level oscillator source.
In RMII Master Mode, a 25 MHz reference is required, either from an
external crystal resonator connected across pins X1 and X2 or from an
external CMOS-level oscillator source connected to pin X1 only.
X2
X2
O
33
CRYSTAL OUTPUT: This pin is the primary clock reference output to
connect to an external 25 MHz crystal resonator device. This pin must be
left unconnected if an external CMOS oscillator clock source is used.
CLK_OUT
CLK_OUT
I/O, PD
24
CLOCK OUTPUT: This pin provides a highly configurable system clock,
which may have one of four sources:
2.
Relative to the internal PTP clock, with a default frequency of 25 MHz
(default)
50 MHz RMII reference clock in RMII Master Mode
3.
25 MHz Receive Clock (same as RX_CLK) in 100 Mb mode
1.
4. 25 MHz or 50 MHz pass-through of X1 reference clock
CLOCK INPUT: This pin is used to input an external IEEE 1588 reference
clock for use by the IEEE 1588 logic. The CLK_OUT_EN strap should be
disabled in the system to prevent possible contention. The PTP_CLKSRC
register must be configured prior to enabling the IEEE 1588 function in
order to allow correct operation.
www.national.com
12
Type
Pin #
Description
LED_LINK
Signal Name
LED_LINK
Pin Name
S, O, PU
28
LINK LED: In Mode 1, this pin indicates the status of the LINK. The LED
will be ON when Link is good.
LINK/ACT LED: In Mode 2 and Mode 3, this pin indicates transmit and
receive activity in addition to the status of the Link. The LED will be ON
when Link is good. It will blink when the transmitter or receiver is active.
LED_SPEED
LED_SPEED/
FX_SD
S, O, PU
27
SPEED LED: The LED is ON when device is in 100 Mb/s and OFF when
in 10 Mb/s. Functionality of this LED is independent of mode selected.
LED_ACT
LED_ACT
S, O, PU
26
ACTIVITY LED: In Mode 1, this pin is the Activity LED which is ON when
activity is present on either Transmit or Receive.
COLLISION/DUPLEX LED: In Mode 2, this pin by default indicates
Collision detection. In Mode 3, this LED output indicates Full-Duplex
status.
8.5 IEEE 1588 EVENT/TRIGGER/CLOCK INTERFACE
Type
Pin #
Description
GPIO1
GPIO2
GPIO3
GPIO4
Signal Name
GPIO1
GPIO2
GPIO3
GPIO4
Pin Name
I/O, PD
21
22
23
25
General Purpose I/O: These pins may be used to signal or detect events.
GPIO5
GPIO6
I/O, PU
26
27
GPIO7
LED_ACT
LED_SPEED/
FX_SD
LED_LINK
General Purpose I/O: These pins may be used to signal or detect events.
Care should be taken when designing systems that use LEDs but use
these pins as GPIOs. To disable the LED functions, refer to Section 14.2.5
LED Direct Control Register (LEDCR).
GPIO8
GPIO9
GPIO8
GPIO9
I/O, PD
36
37
General Purpose I/O: These pins may be used to signal or detect events.
GPIO10
GPIO11
TDO
TDI
I/O, PU
9
12
General Purpose I/O: These pins may be used to signal or detect events.
Care should be taken when designing systems that use the JTAG
interface but use these pins as GPIOs.
GPIO12
CLK_OUT
I/O, PD
24
General Purpose I/O: This pin may be used to signal or detect events or
may output a programmable clock signal synchronized to the internal
IEEE 1588 clock or may be used as an input for an externally generated
IEEE 1588 reference clock. If the system does not require the CLK_OUT
signal, the CLK_OUT output should be disabled via the CLK_OUT_EN
strap.
Type
Pin #
Description
I, PU
8
TEST CLOCK
This pin has a weak internal pullup.
28
8.6 JTAG INTERFACE
Signal Name
Pin Name
TCK
TCK
TDO
TDO
O
9
TEST OUTPUT
TMS
TMS
I, PU
10
TEST MODE SELECT
This pin has a weak internal pullup.
TRST#
TRST#
I, PU
11
TEST RESET: Active low test reset.
This pin has a weak internal pullup.
TDI
TDI
I, PU
12
TEST DATA INPUT
This pin has a weak internal pullup.
13
www.national.com
DP83630
the LED mode strap and a third operational mode which is
register configurable. The definitions for the LEDs for each
mode are detailed below.
8.4 LED INTERFACE
The DP83630 supports three configurable LED pins. The
LEDs support two operational modes which are selected by
DP83630
8.7 RESET AND POWER DOWN
Signal Name
RESET_N
Pin Name
RESET_N
PWRDOWN/INTN PWRDOWN/INTN
www.national.com
Type
Pin #
Description
I, PU
29
RESET: Active Low input that initializes or re-initializes the DP83630.
Asserting this pin low for at least 1 µs will force a reset process to occur.
All internal registers will re-initialize to their default states as specified for
each bit in the Register Block section. All strap options are re-initialized
as well.
I, PU
7
The default function of this pin is POWER DOWN.
POWER DOWN: Asserting this signal low enables the DP83630 Power
Down mode of operation. In this mode, the DP83630 will power down and
consume minimum power. Register access will be available through the
Management Interface to configure and power up the device.
INTERRUPT: This pin may be programmed as an interrupt output instead
of a Powerdown input. In this mode, Interrupts will be asserted low using
this pin. Register access is required for the pin to be used as an interrupt
mechanism. See Section 9.9.2 Interrupt Mechanismsfor more details on
the interrupt mechanisms.
14
Type
Pin #
Description
PHYAD0
PHYAD1
PHYAD2
PHYAD3
PHYAD4
Signal Name
COL
RXD_3
RXD_2
RXD_1
RXD_0
S, O, PU
S, O, PD
S, O, PD
S, O, PD
S, O, PD
42
43
44
45
46
PHY ADDRESS [4:0]: The DP83630 provides five PHY address pins,
the state of which are latched into the PHYCTRL register at system
Hardware-Reset.
The DP83630 supports PHY Address strapping values 0 (<00000>)
through 31 (<11111>).A PHY Address of 0 puts the part into the MII
Isolate Mode. The MII isolate mode must be selected by strapping
PHY Address 0; changing to Address 0 by register write will not put the
PHY in the MII isolate mode.
PHYAD[0] pin has weak internal pull-up resistor.
PHYAD[4:1] pins have weak internal pull-down resistors.
AN_EN
AN1
LED_LINK
LED_SPEED/
FX_SD
LED_ACT
S, O, PU
S, O, PU
28
27
S, O, PU
26
AUTO-NEGOTIATION ENABLE: When high, this enables AutoNegotiation with the capability set by AN0 and AN1 pins. When low,
this puts the part into Forced Mode with the capability set by AN0 and
AN1 pins.
AN0 / AN1: These input pins control the forced or advertised operating
mode of the DP83630 according to the following table. The value on
these pins is set by connecting the input pins to GND (0) or VCC (1)
AN0
Pin Name
through 2.2 kΩ resistors. These pins should NEVER be connected
directly to GND or VCC.
The value set at this input is latched into the DP83630 at HardwareReset.
The float/pull-down status of these pins are latched into the Basic Mode
Control Register and the Auto_Negotiation Advertisement Register
during Hardware-Reset.
The default is 111 since these pins have internal pull-ups.
FIBER MODE DUPLEX SELECTION: If Fiber mode is strapped using
the FX_EN_Z pin (FX_EN_Z = 0), the AN0 strap value is used to select
half or full duplex. AN_EN and AN1 are ignored in Fiber mode since it
is 100 Mb only and does not support Auto-Negotiation. In Fiber mode,
AN1 should not be connected to any system components except the
fiber transceiver.
FX_EN_ AN_EN
Z
AN0
Forced Mode
1
0
0
0
10BASE-T, Half-Duplex
1
0
0
1
10BASE-T, Full-Duplex
1
0
1
0
100BASE-TX, Half-Duplex
1
0
1
1
100BASE-TX, Full-Duplex
0
X
X
0
100BASE-FX, Half-Duplex
0
X
X
1
100BASE-FX, Full-Duplex
AN1
AN0
FX_EN_ AN_EN
Z
15
AN1
Advertised Mode
1
1
0
0
10BASE-T, Half/Full-Duplex
1
1
0
1
100BASE-TX, Half/Full-Duplex
1
1
1
0
100BASE-TX, Full-Duplex
1
1
1
1
10BASE-T, Half/Full-Duplex,
100BASE-TX, Half/Full-Duplex
www.national.com
DP83630
A 2.2 kΩ resistor should be used for pull-down or pull-up to
change the default strap option. If the default option is required, then there is no need for external pull-up or pull down
resistors. Since these pins may have alternate functions after
reset is deasserted, they should not be connected directly to
VCC or GND.
8.8 STRAP OPTIONS
The DP83630 uses many of the functional pins as strap options to place the device into specific modes of operation. The
values of these pins are sampled at power up or hard reset.
During software resets, the strap options are internally reloaded from the values sampled at power up or hard reset. The
strap option pin assignments are defined below. The functional pin name is indicated in parentheses.
DP83630
Signal Name
Pin Name
Type
Pin #
Description
CLK_OUT_EN
GPIO1
S, I, PD
21
CLK_OUT OUTPUT ENABLE: When high, enables clock output on
the CLK_OUT pin at power-up.
FX_EN_Z
RX_ER
S, O, PU
41
FX ENABLE: This strapping option enables 100Base-FX (Fiber)
mode. This mode is disabled by default. An external pull-down will
enable 100Base-FX mode.
LED_CFG
CRS/CRS_DV
S, O, PU
40
LED CONFIGURATION: This strapping option determines the mode
of operation of the LED pins. Default is Mode 1. Mode 1 and Mode 2
can be controlled via the strap option. All modes are configurable via
register access.
See Table 3 for LED Mode Selection.
MII_MODE
RX_DV
S, O, PD
39
MII MODE SELECT: This strapping option determines the operating
mode of the MAC Data Interface. Default operation is MII Mode with a
value of 0 due to the internal pulldown. Strapping MII_MODE high will
cause the device to be in RMII mode of operation.
MII_MODE
MAC Interface Mode
0
MII Mode
1
RMII Mode
PCF_EN
GPIO2
S, I, PD
22
PHY CONTROL FRAME ENABLE: When high, allows the DP83630
to respond to PHY Control Frames.
RMII_MAS
TXD_3
S, I, PD
6
RMII MASTER ENABLE: When MII_MODE is strapped high, this
strapping option enables RMII Master mode, in which the DP83630
uses a 25 MHz crystal connection on X1/X2 and generates the 50 MHz
RMII reference clock. If strapped low when MII_MODE is strapped
high, default RMII operation (RMII Slave) is enabled, in which the
DP83630 uses a 50 MHz oscillator input on X1 as the RMII reference
clock. This strap option is ignored if the MII_MODE strap is low.
8.9 10 Mb/s AND 100 Mb/s PMD INTERFACE
Type
Pin #
Description
TDTD+
Signal Name
TDTD+
I/O
16
17
Differential common driver transmit output (PMD Output Pair). These
differential outputs are automatically configured to either 10BASE-T or
100BASE-TX signaling.
In Auto-MDIX mode of operation, this pair can be used as the Receive
Input pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX Transmit pair.
These pins require 3.3V bias for operation.
RDRD+
RDRD+
I/O
13
14
Differential receive input (PMD Input Pair). These differential inputs are
automatically configured to accept either 100BASE-TX or 10BASE-T
signaling.
In Auto-MDIX mode of operation, this pair can be used as the Transmit
Output pair.
In 100BASE-FX mode, this pair becomes the 100BASE-FX Receive pair.
These pins require 3.3V bias for operation.
FX_SD
LED_SPEED/
FX_SD
S, I/O, PU
27
FIBER MODE SIGNAL DETECT: This pin provides the Signal Detect
input for 100BASE-FX mode.
www.national.com
Pin Name
16
DP83630
8.10 POWER SUPPLY PINS
Signal Name
Pin Name
Type
Pin #
Description
ANAVSS
ANAVSS
Ground
18
Analog Ground
ANA33VDD
ANA33VDD
Supply
19
Analog VDD Supply
CD_VSS
CD_VSS
Ground
15
Analog Ground
IO_CORE_VSS
IO_CORE_VSS
Ground
35
Digital Ground
IO_VDD
IO_VDD
Supply
32
48
I/O VDD Supply
IO_VSS
IO_VSS
Ground
47
Digital Ground
VREF
VREF
20
Bias Resistor Connection. A 4.87 kΩ 1% resistor should be connected
from VREF to GND.
DAP
DAP
No Connect or Connect to GND
See (Note 1)
8.11 PACKAGE PIN ASSIGNMENTS
SQA48A Pin #
Pin Name
SQA48A Pin #
Pin Name
1
TX_CLK
26
LED_ACT
2
TX_EN
27
LED_SPEED/FX_SD
3
TXD_0
28
LED_LINK
4
TXD_1
29
RESET_N
5
TXD_2
30
MDIO
6
TXD_3
31
MDC
7
PWRDOWN/INTN
32
IO_VDD
8
TCK
33
X2
9
TDO
34
X1
10
TMS
35
IO_CORE_VSS
11
TRST#
36
GPIO8
12
TDI
37
GPIO9
13
RD-
38
RX_CLK
14
RD+
39
RX_DV
15
CD_VSS
40
CRS/CRS_DV
16
TD-
41
RX_ER
17
TD+
42
COL
18
ANAVSS
43
RXD_3
19
ANA33VDD
44
RXD_2
20
VREF
45
RXD_1
21
GPIO1
46
RXD_0
22
GPIO2
47
IO_VSS
23
GPIO3
48
IO_VDD
24
CLK_OUT
25
GPIO4
DAP
NC or GND
See (Note 1)
Note 1: Die Attach Pad (DAP) provides thermal dissipation. Connection to GND plane recommended.
17
www.national.com
DP83630
TABLE 1. Auto-Negotiation Modes
9.0 Configuration
AN_EN
This section includes information on the various configuration
options available with the DP83630. The configuration options described below include:
— Media Configuration
— Auto-Negotiation
— PHY Address and LEDs
— Half Duplex vs. Full Duplex
— Isolate mode
— Loopback mode
— BIST
0
0
10BASE-T, Half-Duplex
0
0
1
10BASE-T, Full-Duplex
0
1
0
100BASE-TX, Half-Duplex
1
1
100BASE-TX, Full-Duplex
0
AN1 AN0
Advertised Mode
1
0
0
10BASE-T, Half/Full-Duplex
1
0
1
100BASE-TX, Half/Full-Duplex
1
1
0
100BASE-TX Full-Duplex
1
1
1
10BASE-T, Half/Full-Duplex
100BASE-TX, Half/Full-Duplex
9.2.2 Auto-Negotiation Register Control
When Auto-Negotiation is enabled, the DP83630 transmits
the abilities programmed into the Auto-Negotiation Advertisement register (ANAR) at address 04h via FLP Bursts. Any
combination of 10 Mb/s, 100 Mb/s, Half-Duplex, and Full Duplex modes may be selected.
Auto-Negotiation Priority Resolution:
1. 100BASE-TX Full Duplex (Highest Priority)
2. 100BASE-TX Half Duplex
3. 10BASE-T Full Duplex
4. 10BASE-T Half Duplex (Lowest Priority)
The Basic Mode Control Register (BMCR) at address 00h
provides control for enabling, disabling, and restarting the
Auto-Negotiation process. When Auto-Negotiation is disabled, the SPEED SELECTION bit in the BMCR controls
switching between 10 Mb/s or 100 Mb/s operation, and the
DUPLEX MODE bit controls switching between full duplex
operation and half duplex operation. The SPEED SELECTION and DUPLEX MODE bits have no effect on the mode
of operation when the Auto-Negotiation Enable bit is set.
The Link Speed can be examined through the PHY Status
Register (PHYSTS) at address 10h after a Link is achieved.
The Basic Mode Status Register (BMSR) indicates the set of
available abilities for technology types, Auto-Negotiation ability, and Extended Register Capability. These bits are permanently set to indicate the full functionality of the DP83630 (only
the 100BASE-T4 bit is not set since the DP83630 does not
support that function).
The BMSR also provides status on:
• Whether or not Auto-Negotiation is complete
• Whether or not the Link Partner is advertising that a
remote fault has occurred
• Whether or not valid link has been established
• Support for Management Frame Preamble suppression
The Auto-Negotiation Advertisement Register (ANAR) indicates the Auto-Negotiation abilities to be advertised by the
DP83630. All available abilities are transmitted by default, but
any ability can be suppressed by writing to the ANAR. Updating the ANAR to suppress an ability is one way for a
management agent to change (restrict) the technology that is
used.
The Auto-Negotiation Link Partner Ability Register (ANLPAR)
at address 05h is used to receive the base link code word as
well as all next page code words during the negotiation. Furthermore, the ANLPAR will be updated to either 0081h or
0021h for parallel detection to either 100 Mb/s or 10 Mb/s respectively.
9.2 AUTO-NEGOTIATION
The Auto-Negotiation function provides a mechanism for exchanging configuration information between two ends of a link
segment and automatically selecting the highest performance
mode of operation supported by both devices. Fast Link Pulse
(FLP) Bursts provide the signalling used to communicate Auto-Negotiation abilities between two devices at each end of a
link segment. For further detail regarding Auto-Negotiation,
refer to Clause 28 of the IEEE 802.3u specification. The
DP83630 supports four different Ethernet protocols (10 Mb/s
Half Duplex, 10 Mb/s Full Duplex, 100 Mb/s Half Duplex, and
100 Mb/s Full Duplex), so the inclusion of Auto-Negotiation
ensures that the highest performance protocol will be selected based on the advertised ability of the Link Partner. The
Auto-Negotiation function within the DP83630 can be controlled either by internal register access or by the use of the
AN_EN, AN1 and AN0 pins.
9.2.1 Auto-Negotiation Pin Control
The state of AN_EN, AN0 and AN1 determines whether the
DP83630 is forced into a specific mode or Auto-Negotiation
will advertise a specific ability (or set of abilities) as given in
Table 1. These pins allow configuration options to be selected
without requiring internal register access.
The state of AN_EN, AN0 and AN1, upon power-up/reset,
determines the state of bits [8:5] of the ANAR register.
The Auto-Negotiation function selected at power-up or reset
can be changed at any time by writing to the Basic Mode
Control Register (BMCR) at address 00h.
www.national.com
Forced Mode
0
AN_EN
9.1 MEDIA CONFIGURATION
The DP83630 supports both Twister Pair (100BASE-TX and
10BASE-T) and Fiber (100BASE-FX) media. The port may be
configured for Twisted Pair (TP) or Fiber (FX) operation by
strap option or by register access.
At power-up/reset, the state of the RX_ER pin will select the
media for the port. The default selection is twisted pair mode,
while an external pull-down will select FX mode of operation.
Strapping the port into FX mode also automatically sets the
Far-End Fault Enable, bit 3 of PCSR (16h), the Scramble Bypass, bit 1 of PCSR (16h) and the Descrambler Bypass, bit 0
of PCSR (16h). In addition, the media selection may be controlled by writing to bit 6, FX_EN, of PCSR (16h).
AN1 AN0
18
9.3 AUTO-MDIX
When enabled, this function utilizes Auto-Negotiation to determine the proper configuration for transmission and reception of data and subsequently selects the appropriate MDI pair
for MDI/MDIX operation. The function uses a random seed to
control switching of the crossover circuitry. This implementation complies with the corresponding IEEE 802.3 Auto-Negotiation and Crossover Specifications.
Auto-MDIX is enabled by default and can be configured via
PHYCR (19h) register, bits [15:14].
Neither Auto-Negotiation nor Auto-MDIX is required to be enabled in forcing crossover of the MDI pairs. Forced crossover
can be achieved through the FORCE_MDIX bit, bit 14 of
PHYCR (19h) register.
9.2.3 Auto-Negotiation Parallel Detection
The DP83630 supports the Parallel Detection function as defined in the IEEE 802.3u specification. Parallel Detection
requires both the 10 Mb/s and 100 Mb/s receivers to monitor
the receive signal and report link status to the Auto-Negotiation function. Auto-Negotiation uses this information to configure the correct technology in the event that the Link Partner
does not support Auto-Negotiation but is transmitting link signals that the 100BASE-TX or 10BASE-T PMAs recognize as
valid link signals.
If the DP83630 completes Auto-Negotiation as a result of
Parallel Detection, bits 5 and 7 within the ANLPAR register
will be set to reflect the mode of operation present in the Link
Partner. Note that bits 4:0 of the ANLPAR will also be set to
00001 based on a successful parallel detection to indicate a
valid 802.3 selector field. Software may determine that negotiation completed via Parallel Detection by reading a zero in
the Link Partner Auto-Negotiation Able bit once the Auto-Negotiation Complete bit is set. If configured for parallel detect
mode and any condition other than a single good link occurs
then the parallel detect fault bit will be set.
9.4 AUTO-CROSSOVER IN FORCED MODE
When enabled, this function operates in a manner similar to
Auto-MDIX. If no link activity is seen, switching of the
crossover circuitry is based on a random seed. Valid link activity can be link pulses (Auto-Negotiation link pulse or 10M
link pulses) or 100M signaling. Once valid link activity is seen,
crossover will stop to allow the receive and link functions will
proceed normally.
Auto-crossover in forced mode allows for shorter link times
because it does not require potentially lengthy Auto-Negotiation transactions prior to link establishment. Link establishment via Auto-crossover can be accomplished in full or half
duplex configuration, but both sides of the link must be forced
to the same duplex configuration.
Auto-crossover in forced mode is disabled by default and
must be configured via PCSR (16h) register, bit 15.
Forced crossover can be achieved while Auto-crossover is
enabled through the FORCE_MDIX bit, bit 14 of PHYCR
(19h) register.
NOTE: Auto-MDIX and Auto-crossover in forced mode are
mutually exclusive and should not be enabled concurrently.
Prior to enabling Auto-crossover in forced mode, Auto-Negotiation and Auto-MDIX should be disabled.
9.2.4 Auto-Negotiation Restart
Once Auto-Negotiation has completed, it may be restarted at
any time by setting bit 9 (Restart Auto-Negotiation) of the BMCR to one. If the mode configured by a successful AutoNegotiation loses a valid link, then the Auto-Negotiation
process will resume and attempt to determine the configuration for the link. This function ensures that a valid configuration is maintained if the cable becomes disconnected.
A renegotiation request from any entity, such as a management agent, will cause the DP83630 to halt any transmit data
and link pulse activity until the break_link_timer expires
(~1500 ms). Consequently, the Link Partner will go into link
fail and normal Auto-Negotiation resumes. The DP83630 will
resume Auto-Negotiation after the break_link_timer has expired by issuing FLP (Fast Link Pulse) bursts.
9.5 PHY ADDRESS
The five PHY address strapping pins are shared with the RXD
[3:0] pins and COL pin as shown below.
TABLE 2. PHY Address Mapping
9.2.5 Enabling Auto-Negotiation via Software
It is important to note that if the DP83630 has been initialized
upon power-up as a non-auto-negotiating device (forced
technology), and it is then required that Auto-Negotiation or
re-Auto-Negotiation be initiated via software, bit 12 (Auto-Negotiation Enable) of the Basic Mode Control Register (BMCR)
must first be cleared and then set for any Auto-Negotiation
function to take effect.
Pin #
PHYAD Function
RXD Function
42
PHYAD0
COL
43
PHYAD1
RXD_3
44
PHYAD2
RXD_2
45
PHYAD3
RXD_1
46
PHYAD4
RXD_0
The DP83630 can be set to respond to any of 32 possible
PHY addresses via strap pins. The information is latched into
the PHYCR register (address 19h, bits [4:0]) at device powerup and hardware reset. Each DP83630 or port sharing an
MDIO bus in a system must have a unique physical address.
The DP83630 supports PHY Address strapping values 0
(<00000>) through 31 (<11111>). Strapping PHY Address
0 puts the part into Isolate Mode. It should also be noted
that selecting PHY Address 0 via an MDIO write to PHYCR
will not put the device in Isolate Mode. See for more information.
For further detail relating to the latch-in timing requirements
of the PHY Address pins, as well as the other hardware con-
9.2.6 Auto-Negotiation Complete Time
Parallel detection and Auto-Negotiation take approximately
2-3 seconds to complete. In addition, Auto-Negotiation with
next page should take approximately 2-3 seconds to complete, depending on the number of next pages sent.
Refer to Clause 28 of the IEEE 802.3u standard for a full description of the individual timers related to Auto-Negotiation.
19
www.national.com
DP83630
The Auto-Negotiation Expansion Register (ANER) indicates
additional Auto-Negotiation status. The ANER provides status on:
• Whether or not a Parallel Detect Fault has occurred
• Whether or not the Link Partner supports the Next Page
function
• Whether or not the DP83630 supports the Next Page
function
• Whether or not the current page being exchanged by AutoNegotiation has been received
• Whether or not the Link Partner supports Auto-Negotiation
DP83630
figuration pins, refer to the Reset summary in Section 12.0
Reset Operation.
Since the PHYAD[0] pin has weak internal pull-up resistor and
PHYAD[4:1] pins have weak internal pull-down resistors, the
default setting for the PHY address is 00001 (01h).
Refer to Figure 2for an example of a PHYAD connection to
external components. In this example, the PHYAD strapping
results in address 00011 (03h).
presents a high impedance on the TX_CLK, RX_CLK,
RX_DV, RX_ER, RXD[3:0], COL, and CRS/CRS_DV outputs.
When in Isolate Mode, the DP83630 will continue to respond
to all serial management transactions over the MII.
While in Isolate Mode, the PMD output pair will not transmit
packet data but will continue to source 100BASE-TX scrambled idles or 10BASE-T normal link pulses.
The DP83630 can Auto-Negotiate or parallel detect to a specific technology depending on the receive signal at the PMD
input pair. A valid link can be established for the receiver even
when the DP83630 is in Isolate Mode.
9.5.1 MII Isolate Mode
It is recommended that the user have a basic understanding
of Clause 22 of the 802.3u standard.
The DP83630 can be put into MII Isolate Mode by writing a 1
to bit 10 of the BMCR register. Strapping the PHY Address to
0 will force the device into Isolate Mode when powered up. It
should be noted that selecting Physical Address 0 via an
MDIO write to PHYCR will not put the device in the MII isolate
mode.
When in the MII Isolate Mode, the DP83630 does not respond
to packet data present at TXD[3:0] and TX_EN inputs and
9.5.2 Broadcast Mode
The DP83630 is also capable of accepting broadcast messages (register writes to PHY address 0x1F). Setting the
BC_WRITE to 1, bit 11 of the PHY Control Register 2 (PHYCR2) at address 0x1C, will configure the device to accept
broadcast messages independent of the local PHY Address
value.
30136201
FIGURE 2. PHYAD Strapping Example
mode can be selected by writing to the LED_CFG[1:0] register
bits in the PHY Control Register (PHYCR) at address 19h,
bits [6:5]. LED_CFG[1] is only controllable through register
access and cannot be set by a strap pin.
See Table 3 for LED Mode selection.
9.6 LED INTERFACE
The DP83630 supports three configurable Light Emitting
Diode (LED) pins: LED_LINK, LED_SPEED/FX_SD, and
LED_ACT.
Several functions can be multiplexed onto the three LEDs using three different modes of operation. The LED operation
TABLE 3. LED Mode Selection
Mode
LED_CFG[1]
LED_CFG[0]
LED_LINK
1
don't care
1
ON for Good Link
OFF for No Link
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Activity
OFF for No Activity
2
0
0
ON for Good Link
BLINK for Activity
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Collision
OFF for No Collision
3
1
0
ON for Good Link
BLINK for Activity
ON in 100 Mb/s
OFF in 10 Mb/s
ON for Full Duplex
OFF for Half Duplex
The LED_LINK pin in Mode 1 indicates the link status of the
port. In 100BASE-TX mode, link is established as a result of
input receive amplitude compliant with the TP-PMD specifications which will result in internal generation of signal detect.
www.national.com
LED_SPEED
LED_ACT
A 10 Mb/s Link is established as a result of the reception of
at least seven consecutive normal Link Pulses or the reception of a valid 10BASE-T packet. This will cause the assertion
of LED_LINK. LED_LINK will deassert in accordance with the
20
DP83630
Link Loss Timer as specified in the IEEE 802.3 specification.
In 100BASE-TX mode, an optional fast link loss detection may
be enabled by setting the SD_TIME control in the SD_CNFG
register. Enabling fast link loss detection will result in the
LED_LINK deassertion within approximately 1.3 µs of loss of
signal on the wire.
The LED_LINK pin in Mode 1 will be OFF when no LINK is
present.
The LED_LINK pin in Mode 2 and Mode 3 will be ON to indicate Link is good and BLINK to indicate activity is present on
activity. The BLINK frequency is defined in BLINK_FREQ, bits
[7:6] of register LEDCR (18h).
Activity is defined as configured in LEDACT_RX, bit 8 of register LEDCR (18h). If LEDACT_RX is 0, Activity is signaled
for either transmit or receive. If LEDACT_RX is 1, Activity is
only signaled for receive.
The LED_SPEED/FX_SD pin indicates 10 or 100 Mb/s data
rate of the port. The standard CMOS driver goes high when
operating in 100 Mb/s operation. The functionality of this LED
is independent of mode selected.
The LED_ACT pin in Mode 1 indicates the presence of either
transmit or receive activity. The LED will be ON for Activity
and OFF for No Activity. In Mode 2, this pin indicates the Collision status of the port. The LED will be ON for Collision and
OFF for No Collision.
The LED_ACT pin in Mode 3 indicates Duplex status for 10
Mb/s or 100 Mb/s operation. The LED will be ON for Full Duplex and OFF for Half Duplex.
In 10 Mb/s half duplex mode, the collision LED is based on
the COL signal.
Since these LED pins are also used as strap options, the polarity of the LED is dependent on whether the pin is pulled up
or down.
30136202
FIGURE 3. AN Strapping and LED Loading Example
9.6.2 LED Direct Control
The DP83630 provides another option to directly control any
or all LED outputs through the LED Direct Control Register
(LEDCR), address 18h. The register does not provide read
access to LEDs.
9.7 HALF DUPLEX vs. FULL DUPLEX
The DP83630 supports both half and full duplex operation at
both 10 Mb/s and 100 Mb/s speeds.
Half-duplex relies on the CSMA/CD protocol to handle collisions and network access. In Half-Duplex mode, Carrier
Sense (CRS) responds to both transmit and receive activity
in order to maintain compliance with the IEEE 802.3 specification.
Since the DP83630 is designed to support simultaneous
transmit and receive activity it is capable of supporting fullduplex switched applications with a throughput of up to 200
Mb/s when operating in either 100BASE-TX or 100BASE-FX.
Because the CSMA/CD protocol does not apply to full-duplex
operation, the DP83630 disables its own internal collision
sensing and reporting functions and modifies the behavior of
CRS such that it indicates only receive activity. This allows a
full-duplex capable MAC to operate properly.
All modes of operation (100BASE-TX, 100BASE-FX,
10BASE-T) can run either half-duplex or full-duplex. Additionally, other than CRS and collision reporting, all remaining
MII signaling remains the same regardless of the selected
duplex mode.
It is important to understand that while Auto-Negotiation with
the use of Fast Link Pulse code words can interpret and configure to full-duplex operation, parallel detection can not recognize the difference between full and half-duplex from a fixed
10 Mb/s or 100 Mb/s link partner over twisted pair. As specified in the 802.3u specification, if a far-end link partner is
configured to a forced full-duplex 100BASE-TX ability, the
parallel detection state machine in the partner would be unable to detect the full-duplex capability of the far-end link
partner. This link segment would negotiate to a half-duplex
100BASE-TX configuration (same scenario for 10 Mb/s).
9.6.1 LEDs
Since the Auto-Negotiation (AN) strap options share the LED
output pins, the external components required for strapping
and LED usage must be considered in order to avoid contention.
Specifically, when the LED outputs are used to drive LEDs
directly, the active state of each output driver is dependent on
the logic level sampled by the corresponding AN input upon
power-up/reset. For example, if a given AN input is resistively
pulled low then the corresponding output will be configured
as an active high driver. Conversely, if a given AN input is
resistively pulled high, then the corresponding output will be
configured as an active low driver.
Refer to for an example of AN connections to external components. In this example, the AN strapping results in AutoNegotiation disabled with 100 Full-Duplex forced.
The adaptive nature of the LED outputs helps to simplify potential implementation issues of these dual purpose pins.
21
www.national.com
DP83630
Auto-Negotiation is not supported in 100BASE-FX operation.
Selection of Half or Full-duplex operation is controlled by bit
8 of the Basic Mode Control Register (BMCR), address 00h.
If 100BASE-FX mode is strapped using the RX_ER pin, the
AN0 strap value is used to set the value of bit 8 of the BMCR
(00h) register. Note that the other Auto-Negotiation strap pins
(AN_EN and AN1) are ignored in 100BASE-FX mode.
monitoring the transmission line. Activity on the line will cause
the DP83630 to go through a normal power up sequence.
Regardless of cable activity, the DP83630 will occasionally
wake up the transmitter to put ED pulses on the line, but will
otherwise draw as little power as possible. Energy detect
functionality is controlled via register Energy Detect Control
(EDCR), address 1Dh.
9.8 INTERNAL LOOPBACK
The DP83630 includes a Loopback Test mode for facilitating
system diagnostics. The Loopback mode is selected through
bit 14 (Loopback) of the Basic Mode Control Register (BMCR). Writing 1 to this bit enables MII transmit data to be routed
to the MII receive outputs. Loopback status may be checked
in bit 3 of the PHY Status Register (PHYSTS). While in Loopback mode the data will not be transmitted onto the media. To
ensure that the desired operating mode is maintained, AutoNegotiation should be disabled before selecting the Loopback
mode.
9.11 LINK DIAGNOSTIC CAPABILITIES
The DP83630 contains several system diagnostic capabilities
for evaluating link quality and detecting potential cabling faults
in twisted pair cabling. Software configuration is available
through the Link Diagnostics Registers - Page 2 which can be
selected via Page Select Register (PAGESEL), address 13h.
These capabilities include:
— Linked Cable Status
— Link Quality Monitor
— TDR (Time Domain Reflectometry) Cable Diagnostics
9.9 POWER DOWN/INTERRUPT
The Power Down and Interrupt functions are multiplexed on
pin 7 of the device. By default, this pin functions as a power
down input and the interrupt function is disabled. Setting bit 0
(INT_OE) of MICR (11h) will configure the pin as an active
low interrupt output.
9.11.1 Linked Cable Status
In an active connection with a valid link status, the following
diagnostic capabilities are available:
— Polarity reversal
— Cable swap (MDI vs MDIX) detection
— 100 Mb Cable Length Estimation
— Frequency offset relative to link partner
— Cable Signal Quality Estimation
9.9.1 Power Down Control Mode
The PWRDOWN/INTN pin can be asserted low to put the device in a Power Down mode. This is equivalent to setting bit
11 (POWER DOWN) in the Basic Mode Control Register,
BMCR (00h). An external control signal can be used to drive
the pin low, overcoming the weak internal pull-up resistor. Alternatively, the device can be configured to initialize into a
Power Down state by use of an external pull-down resistor on
the PWRDOWN/INTN pin. Since the device will still respond
to management register accesses, setting the INT_OE bit in
the MICR register will disable the PWRDOWN/INTN input,
allowing the device to exit the Power Down state.
9.11.1.1 Polarity Reversal
The DP83630 detects polarity reversal by detecting negative
link pulses. The Polarity indication is available in bit 12 of the
PHYSTS (10h) or bit 4 of the 10BTSCR (1Ah). Inverted polarity indicates the positive and negative conductors in the
receive pair are swapped. Since polarity is corrected by the
receiver, this does not necessarily indicate a functional problem in the cable.
Since the polarity indication is dependent on link pulses from
the link partner, polarity indication is only valid in 10 Mb modes
of operation, or in 100 Mb Auto-Negotiated mode. Polarity indication is not available in 100 Mb forced mode of operation
or in a parallel detected 100 Mb mode.
9.9.2 Interrupt Mechanisms
The interrupt function is controlled via register access. All interrupt sources are disabled by default. Setting bit 1 (INTEN)
of MICR (11h) will enable interrupts to be output, dependent
on the interrupt mask set in the lower byte of the MISR (12h).
The PWRDOWN/INTN pin is asynchronously asserted low
when an interrupt condition occurs. The source of the interrupt
can be determined by reading the upper byte of the MISR.
One or more bits in the MISR will be set, denoting all currently
pending interrupts. Reading of the MISR clears ALL pending
interrupts.
Example: To generate an interrupt on a change of link status
or on a change of energy detect power state, the steps would
be:
• Write 0003h to MICR to set INTEN and INT_OE
• Write 0060h to MISR to set ED_INT_EN and
LINK_INT_EN
• Monitor PWRDOWN/INTN pin
When PWRDOWN/INTN pin asserts low, the user would read
the MISR register to see if the ED_INT or LINK_INT bits are
set, i.e. which source caused the interrupt. After reading the
MISR, the interrupt bits should clear and the PWRDOWN/
INTN pin will de-assert.
9.11.1.2 Cable Swap Indication
As part of Auto-Negotiation, the DP83630 has the ability (using Auto-MDIX) to automatically detect a cable with swapped
MDI pairs and select the appropriate pairs for transmitting and
receiving data. Normal operation is termed MDI, while
crossed operation is MDIX. The MDIX status can be read from
bit 14 of the PHYSTS (10h).
9.11.1.3 100 Mb Cable Length Estimation
The DP83630 provides a method of estimating cable length
based on electrical characteristics of the 100 Mb link. This
essentially provides an effective cable length rather than a
measurement of the physical cable length. The cable length
estimation is only available in 100 Mb mode of operation with
a valid link status. The cable length estimation is available at
the Link Diagnostics Registers - Page 2, register 100 Mb
Length Detect (LEN100_DET), address 14h.
9.11.1.4 Frequency Offset Relative to Link Partner
As part of the 100 Mb clock recovery process, the DSP implementation provides a frequency control parameter. This
value may be used to indicate the frequency offset of the device relative to the link partner. This operation is only available
in 100 Mb operation with a valid link status. The frequency
9.10 ENERGY DETECT MODE
When Energy Detect is enabled and there is no activity on the
cable, the DP83630 will remain in a low power mode while
www.national.com
22
nostics Registers - Page 2. The LQMR register includes a
global enable to enable the Link Quality Monitor function. In
addition, it provides warning status from both high and low
thresholds for each of the monitored parameters except SNR
Variance.. The LQMR2 register provides warning status for
the high threshold of SNR Variance (upper 16 bits); there is
no low threshold. Note that individual low or high parameter
threshold comparisons can be disabled by setting to the minimum or maximum values.
To allow the Link Quality Monitor to interrupt the system, the
Interrupt must be enabled through the interrupt control registers, MICR (11h) and MISR (12h).
The Link Quality Monitor may also be used to automatically
reset the DSP and restart adaption. Separate enable bits in
LQMR and LQMR2 allow for automatic reset based on each
of the parameter values. If enabled, a violation of one of the
thresholds will result in a restart of the DSP adaption. In addition if the PCSR:SD_OPTION register bit is set to 0, the
violation will also result in a drop in Link Status.
9.11.1.5 Cable Signal Quality Estimation
The cable signal quality estimator keeps a simple tracking of
results of the DSP and can be used to generate an approximate Signal-to-Noise Ratio for the 100 Mb receiver. This
information is available to software through the Link Diagnostics Registers - Page 2: Variance Control Register
(VAR_CTRL), address 1Ah and Variance Data Register
(VAR_DATA), address 1Bh.
The variance computation times (VAR_TIMER) can be chosen from the set of {2, 4, 6, 8} ms. The 32-bit variance sum
can be read by two consecutive reads of the VAR_DATA register. This sum can be used to compute an SNR estimate by
software using the following equation:
SNR = 10log10((37748736 * VAR_TIMER) / Variance).
9.11.2.2 Checking Current Parameter Values
Prior to setting Threshold values, it is recommended that software check current adapted values. The thresholds may then
be set relative to the adapted values. The current adapted
values can be read using the LQDR register by setting the
SAMPLE_PARAM bit [13] of LQDR, address (1Eh).
For example, to read the DBLW current value:
1. Write 2400h to LQDR (1Eh) to set the SAMPLE_PARAM
bit and set the LQ_PARAM_SEL[2:0] to 010.
2. Read LQDR (1Eh). Current DBLW value is returned in
the low 8 bits.
9.11.2 Link Quality Monitor
The Link Quality Monitor allows a method to generate an
alarm when the DSP adaption strays from a programmable
window. This could occur due to changes in the cable which
could indicate a potential problem. Software can program
thresholds for the following DSP parameters to be used to
interrupt the system:
— Digital Equalizer C1 Coefficient (DEQ C1)
— Digital Adaptive Gain Control (DAGC)
— Digital Base-Line Wander Control (DBLW)
— Recovered Clock Long-Term Frequency Offset (FREQ)
— Recovered Clock Frequency Control (FC)
— Signal-to-Noise Ratio (SNR) Variance
Software is expected to read initial adapted values and then
program the thresholds based on an expected valid range.
This mechanism takes advantage of the fact that the DSP
adaptation should remain in a relatively small range once a
valid link has been established.
9.11.2.3 Threshold Control
The LQDR (1Eh) register also provides a method of programming high and low thresholds for each of the five parameters
that can be monitored. The register implements an indirect
read/write mechanism.
Writes are accomplished by writing data, address, and a write
strobe to the register. Reads are accomplished by writing the
address to the register, and reading back the value of the selected threshold. Setting thresholds to the maximum or minimum values will disable the threshold comparison since
values have to exceed the threshold to generate a warning
condition.
Warnings are not generated if the parameter is equal to the
threshold. By default, all thresholds are disabled by setting to
the minimum or maximum values. The Table 4 shows the five
parameters and range of values:
9.11.2.1 Link Quality Monitor Control and Status
Control of the Link Quality Monitor is done through the Link
Quality Monitor Register (LQMR), address 1Dh and the Link
Quality Data Register (LQDR), address 1Bh of the Link Diag-
TABLE 4. Link Quality Monitor Parameter Ranges
Parameter
DEQ_C1
Minimum Value
Maximum Value
Min (2-s comp)
Max (2-s comp)
-128
+127
0x80
0x7F
DAGC
0
+255
0x00
0xFF
DBLW
-128
+127
0x80
0x7F
Frequency Offset
-128
+127
0x80
0x7F
Frequency Control
-128
+127
0x80
0x7F
0
+2304
0x0000
0x900
SNR Variance
Note that values are signed 2-s complement values except
for DAGC and Variance which are always positive. The maximum SNR Variance is calculated by assuming the worstcase squared error (144) is accumulated every 8 ns for
8*220 ns (roughly 8 ms or exactly 1,048,576 clock cycles).
For example, to set the DBLW Low threshold to -38:
1. Write 14DAh to LQDR to set the Write_LQ_Thr bit, select
the DBLW Low Threshold, and write data of -38 (0xDA).
2. Write 8000 to LQMR to enable the Link Quality Monitor
(if not already enabled).
23
www.national.com
DP83630
offset can be determined using the register 100 Mb Frequency Offset Indication (FREQ100), address 15h, of the Link
Diagnostics Registers - Page 2.
Two different versions of the Frequency Offset may be monitored through bits [7:0] of register FREQ100 (15h). The first
is the long-term Frequency Offset. The second is the current
Frequency Control value, which includes short-term phase
adjustments and can provide information on the amount of
jitter in the system.
DP83630
•
Transmit Pulse Width: Bits [10:8] of TDR_CTRL (16h)
allows sending of 0 to 7 clock width pulses. Actual pulses
are dependent on the transmit mode. If the pulse width is
set to 0, then no pulse will be sent.
• Transmit Channel Select: The transmitter can send
pulses down either the transmit pair or the receive pair by
enabling bit 13 of TDR_CTRL (16h). Default value is to
select the transmit pair.
The following receive mode controls are available:
• Min/Max Mode Control: Bit 7 of TDR_CTRL (16h)
controls the TDR Monitor operation. In default mode, the
monitor will detect maximum (positive) values. In Min
Mode, the monitor will detect minimum (negative) values.
• Receive Channel Select: The receiver can monitor either
the transmit pair or the receive pair by enabling bit 12 of
TDR_CTRL (16h). Default value is to select the transmit
pair.
• Receive Window: The receiver can monitor receive data
within a programmable window using the TDR Window
Register (TDR_WIN), address 17h. The window is
controlled by two register values: TDR Start Window, bits
[15:8] of TDR_WIN (17h) and TDR Stop Window, bits [7:0]
of TDR_WIN (17h). The TDR Start Window indicates the
first clock to start sampling. The TDR Stop Window
indicates the last clock to sample. By default, the full
window is enabled, with Start set to 0 and Stop set to 255.
The window range is in 8 ns clock increments, so the
maximum window size is 2048 ns.
9.11.3 TDR Cable Diagnostics
The DP83630 implements a Time Domain Reflectometry
(TDR) method of cable length measurement and evaluation
which can be used to evaluate a connected twisted pair cable.
The TDR implementation involves sending a pulse out on either the Transmit or Receive conductor pair and observing the
results on either pair. By observing the types and strength of
reflections on each pair, software can determine the following:
— Cable short
— Cable open
— Distance to fault
— Identify which pair has a fault
— Pair skew
The TDR cable diagnostics works best in certain conditions.
For example, an unterminated cable provides a good reflection for measuring cable length, while a cable with an ideal
termination to an unpowered partner may provide no reflection at all.
9.11.4 TDR Pulse Generator
The TDR implementation can send two types of TDR pulses.
The first option is to send 50 ns or 100 ns link pulses from the
10 Mb Common Driver. The second option is to send pulses
from the 100 Mb Common Driver in 8 ns increments up to 56
ns in width. The 100 Mb pulses will alternate between positive
and negative pulses. The shorter pulses provide better ability
to measure short cable lengths, especially since they will limit
overlap between the transmitted pulse and a reflected pulse.
The longer pulses may provide better measurements of long
cable lengths.
In addition, if the pulse width is programmed to 0, no pulse
will be sent, but the monitor circuit will still be activated. This
allows sampling of background data to provide a baseline for
analysis.
9.11.7 TDR Results
The results of a TDR peak and threshold measurement are
available in the TDR Peak Measurement Register
(TDR_PEAK), address 18h and TDR Threshold Measurement Register (TDR_THR), address 19h. The threshold measurement may be a more accurate method of measuring the
length of longer cables since it provides a better indication of
the start of the received pulse, rather than the peak value.
Software utilizing the TDR function should implement an algorithm to send TDR pulses and evaluate results. Multiple
runs should be used to best qualify any received pulses as
multiple reflections could exist. In addition, when monitoring
the transmitting pair, the window feature should be used to
disqualify the transmitted pulse. Multiple runs may also be
used to average the values providing more accurate results.
Actual distance measurements are dependent on the velocity
of propagation of the cable. The delay value is typically on the
order of 4.6 to 4.9 ns/m.
9.11.5 TDR Pulse Monitor
The TDR function monitors data from the Analog to Digital
Converter (ADC) to detect both peak values and values above
a programmable threshold. It can be programmed to detect
maximum or minimum values. In addition, it records the time,
in 8 ns intervals, at which the peak or threshold value first
occurs.
The TDR monitor implements a timer that starts when the
pulse is transmitted. A window may be enabled to qualify incoming data to look for response only in a desired range. This
is especially useful for eliminating the transmitted pulse, but
also may be used to look for multiple reflections.
9.12 BIST
The DP83630 incorporates an internal Built-in Self Test
(BIST) circuit to accommodate in-circuit testing or diagnostics. The BIST circuit can be utilized to test the integrity of the
transmit and receive data paths. BIST testing can be performed with the part in the internal loopback mode or externally looped back using a loopback cable fixture. BIST testing
can also be performed between two directly connected
DP83630 devices.
The BIST is implemented with independent transmit and receive paths, with the transmit block generating a continuous
stream of a pseudo random sequence. The user can select a
9 bit or 15 bit pseudo random sequence from the PSR_15 bit
in the PHY Control Register (PHYCR). The received data is
compared to the generated pseudo-random data by the BIST
Linear Feedback Shift Register (LFSR) to determine the BIST
pass/fail status.
9.11.6 TDR Control Interface
The TDR Control Interface is implemented in the Link Diagnostics Registers - Page 2 through TDR Control
(TDR_CTRL), address 16h and TDR Window (TDR_WIN),
address 17h. The following basic controls are:
• TDR Enable: Enable bit 15 of TDR_CTRL (16h) to allow
the TDR function. This bypasses normal operation and
gives control of the CD10 and CD100 block to the TDR
function.
• TDR Send Pulse: Enable bit 11 of TDR_CTRL (16h) to
send the TDR pulse and starts the TDR Monitor
The following transmit mode controls are available:
• Transmit Mode: Enables use of 10 Mb Link pulses from
the 10 Mb Common Driver or data pulses from the 100 Mb
Common Driver by enabling TDR_100 Mb, bit 14 of
TDR_CRTL (16h).
www.national.com
24
10.1.2 Collision Detect
For Half Duplex, a 10BASE-T or 100BASE-TX collision is detected when the receive and transmit channels are active
simultaneously. Collisions are reported by the COL signal on
the MII.
If the DP83630 is transmitting in 10 Mb/s mode when a collision is detected, the collision is not reported until seven bits
have been received while in the collision state. This prevents
a collision being reported incorrectly due to noise on the network. The COL signal remains set for the duration of the
collision.
If a collision occurs during a receive operation, it is immediately reported by the COL signal.
When heartbeat is enabled (only applicable to 10 Mb/s operation), approximately 1µs after the transmission of each packet, a Signal Quality Error (SQE) signal of approximately 10 bit
times is generated (internally) to indicate successful transmission. SQE is reported as a pulse on the COL signal of the
MII.
Collision is not indicated during Full Duplex operation.
10.0 MAC Interface
The DP83630 supports several modes of operation using the
MII interface pins. The options are defined in the following
sections and include:
— MII Mode
— RMII Mode
— Single Clock MII Mode (SCMII)
In addition, the DP83630 supports the standard 802.3u MII
Serial Management Interface.
The modes of operation can be selected by strap options or
register control. For RMII Slave mode, it is recommended to
use the strap option since it requires a 50 MHz clock instead
of the normal 25 MHz.
In each of these modes, the IEEE 802.3 serial management
interface is operational for device configuration and status.
The serial management interface of the MII allows for the
configuration and control of multiple PHY devices, gathering
of status, error information, and the determination of the type
and capabilities of the attached PHY(s).
10.1.3 Carrier Sense
In 10 Mb/s operation, Carrier Sense (CRS) is asserted due to
receive activity once valid data is detected via the Smart
Squelch function. During 100 Mb/s operation CRS is asserted
when a valid link (SD) and two non-contiguous zeros are detected on the line.
For 10 or 100 Mb/s Half Duplex operation, CRS is asserted
during either packet transmission or reception.
For 10 or 100 Mb/s Full Duplex operation, CRS is asserted
only due to receive activity.
CRS is deasserted following an end of packet.
10.1 MII INTERFACE
The DP83630 incorporates the Media Independent Interface
(MII) as specified in Clause 22 of the IEEE 802.3u standard.
This interface may be used to connect PHY devices to a MAC
in 10/100 Mb/s systems. This section describes the nibble
wide MII data interface.
The nibble wide MII data interface consists of a receive bus
and a transmit bus each with control signals to facilitate data
transfer between the PHY and the upper layer (MAC).
10.2 REDUCED MII INTERFACE
The DP83630 incorporates the Reduced Media Independent
Interface (RMII) as specified in the RMII specification (rev 1.2)
from the RMII Consortium. This interface may be used to
connect PHY devices to a MAC in 10/100 Mb/s systems using
a reduced number of pins. In this mode, data is transferred 2bits at a time using the 50 MHz RMII_REF clock for both
transmit and receive. The following pins are used in RMII
mode:
— TX_EN
— TXD[1:0]
— RX_ER (optional for MAC)
— CRS/CRS_DV
— RXD[1:0]
— X1 (25 MHz in RMII Master mode, 50 MHz in RMII Slave
mode)
— RX_CLK, TX_CLK, CLK_OUT (50 MHz RMII reference
clock in RMII Master mode only)
In addition, the RMII mode supplies an RX_DV signal which
allows for a simpler method of recovering receive data without
having to separate RX_DV from the CRS_DV indication. This
is especially useful for systems which do not require CRS,
such as systems that only support full-duplex operation. This
signal is also useful for diagnostic testing where it may be
desirable to loop external Receive RMII data directly to the
transmitter.
The RX_ER output may be used by the MAC to detect error
conditions. It is asserted for symbol errors received during a
packet, False Carrier events, and also for FIFO underrun or
overrun conditions. Since the PHY is required to corrupt receive data on an error, a MAC is not required to use RX_ER.
10.1.1 Nibble-wide MII Data Interface
Clause 22 of the IEEE 802.3u specification defines the Media
Independent Interface. This interface includes a dedicated
receive bus and a dedicated transmit bus. These two data
buses, along with various control and status signals, allow for
the simultaneous exchange of data between the DP83630
and the upper layer agent (MAC).
The receive interface consists of a nibble wide data bus RXD
[3:0], a receive error signal RX_ER, a receive data valid flag
RX_DV, and a receive clock RX_CLK for synchronous transfer of the data. The receive clock operates at either 2.5 MHz
to support 10 Mb/s operation modes or at 25 MHz to support
100 Mb/s operational modes.
The transmit interface consists of a nibble wide data bus TXD
[3:0], a transmit enable control signal TX_EN, and a transmit
clock TX_CLK which runs at either 2.5 MHz or 25 MHz.
Additionally, the MII includes the carrier sense signal CRS, as
well as a collision detect signal COL. The CRS signal asserts
to indicate the reception of data from the network or as a
function of transmit data in Half Duplex mode. The COL signal
asserts as an indication of a collision which can occur during
half-duplex operation when both a transmit and receive operation occur simultaneously.
25
www.national.com
DP83630
The pass/fail status of the BIST is stored in the BIST status
bit in the PHYCR register. The status bit defaults to 0 (BIST
fail) and will transition on a successful comparison. If an error
(mis-compare) occurs, the status bit is latched and is cleared
upon a subsequent write to the Start/Stop bit.
For transmit VOD testing, the Packet BIST Continuous Mode
can be used to allow continuous data transmission by setting
the BIST_CONT_MODE, bit 5, of CDCTRL1 (1Bh).
The number of BIST errors can be monitored through the
BIST Error Count in the CDCTRL1 (1Bh), bits [15:8].
DP83630
Since the reference clock operates at 10 times the data rate
for 10 Mb/s operation, transmit data is sampled every 10
clocks. Likewise, receive data will be generated every 10th
clock so that an attached device can sample the data every
10 clocks.
RMII Slave mode requires a 50 MHz oscillator to be connected to the device X1 pin. A 50 MHz crystal is not supported.
RMII Master mode can use either a 25 MHz oscillator connected to X1 or a 25 MHz crystal connected to X1 and X2.
To tolerate potential frequency differences between the 50
MHz reference clock and the recovered receive clock, the receive RMII function includes a programmable elasticity buffer.
The elasticity buffer is programmable to minimize propagation
delay based on expected packet size and clock accuracy.
This allows for supporting a range of packet sizes including
jumbo frames.
The elasticity buffer will force Frame Check Sequence errors
for packets which overrun or underrun the FIFO. Underrun
and overrun conditions can be reported in the RMII and Bypass Register (RBR). Table 5 indicates how to program the
elasticity buffer FIFO (in 4-bit increments) based on expected
maximum packet size and clock accuracy. It assumes both
clocks (RMII Reference clock and far-end Transmitter clock)
have the same accuracy.
Packet lengths can be scaled linearly based on accuracy (+/25 ppm would allow packets twice as large). If the threshold
setting must support both 10 Mb and 100 Mb operation, the
setting should be made to support both speeds.
TABLE 5. Supported Packet Sizes at +/-50 ppm Frequency Accuracy
Start Threshold RBR[1:0]
Latency Tolerance
Recommended Packet Size at +/- 50 ppm
100 Mb
10 Mb
100 Mb
10 Mb
01 (default)
2 bits
8 bits
2,400 bytes
9,600 bytes
10
6 bits
4 bits
7,200 bytes
4,800 bytes
11
10 bits
8 bits
12,000 bytes
9,600 bytes
00
14 bits
12 bits
16,800 bytes
14,400 bytes
three clocks, a reference clock for physical layer functions, a
transmit MII clock, and a receive MII clock. Similar to RMII
mode, Single Clock MII mode requires only the reference
clock. In addition to reducing the number of pins required, this
mode allows the attached MAC device to use only the reference clock domain. AC Timing requirements for SCMII operation are similar to the RMII timing requirements.
For 10 Mb operation, as in RMII mode, data is sampled and
driven every 10 clocks since the reference clock is at 10 times
the data rate.
Separate control bits allow enabling the Transmit and Receive Single Clock modes separately, allowing just transmit
or receive to operate in this mode. Control of Single Clock MII
mode is through the RBR register.
Single Clock MII mode incorporates the use of the RMII elasticity buffer, which is required to tolerate potential frequency
differences between the 25 MHz reference clock and the recovered receive clock. Settings for the elasticity buffer for
SCMII mode are detailed in Table 6.
10.2.1 RMII Master Mode
In RMII Master Mode, the DP83630 uses a 25 MHz crystal on
X1/X2 and internally generates the 50 MHz RMII reference
clock for use by the RMII logic. The 50 MHz clock is output
on RX_CLK, TX_CLK, and CLK_OUT for use as the reference clock for an attached MAC. RX_CLK operates at 25 MHz
during reset.
10.2.2 RMII Slave Mode
In RMII Slave Mode, the DP83630 takes a 50 MHz reference
clock input on X1 from an external oscillator or another
DP83630 in RMII Master Mode. The 50 MHz is internally divided down to 25 MHz for use as the reference clock for nonRMII logic. RX_CLK, TX_CLK, and CLK_OUT should not be
used as the RMII reference clock in this mode but may be
used for other system devices.
10.3 SINGLE CLOCK MII MODE
Single Clock MII (SCMII) Mode allows MII operation using a
single 25 MHz reference clock. Normal MII Mode requires
TABLE 6. Supported SCMII Packet Sizes at +/-50 ppm Frequency Accuracy
Start Threshold RBR[1:0]
Latency Tolerance
Recommended Packet Size at +/- 50 ppm
100 Mb
10 Mb
100 Mb
10 Mb
01 (default)
4 bits
8 bits
4,000 bytes
9,600 bytes
10
4 bits
8 bits
4,000 bytes
9,600 bytes
11
8 bits
8 bits
9,600 bytes
9,600 bytes
00
8 bits
8 bits
9,600 bytes
9,600 bytes
10.4 IEEE 802.3u MII SERIAL MANAGEMENT INTERFACE
10.4.2 Serial Management Access Protocol
The serial control interface consists of two pins, Management
Data Clock (MDC) and Management Data Input/Output
(MDIO). MDC has a maximum clock rate of 25 MHz and no
minimum rate. The MDIO line is bi-directional and may be
shared by up to 32 devices. The MDIO frame format is shown
below in Table 7.
The MDIO pin requires a pull-up resistor (1.5 kΩ) which, during IDLE and turnaround, will pull MDIO high. The DP83630
also includes an option to enable an internal pull-up on the
MDIO pin, MDIO_PULL_EN bit in the CDCTRL1 register. In
10.4.1 Serial Management Register Access
The serial management MII specification defines a set of thirty-two 16-bit status and control registers that are accessible
through the management interface pins MDC and MDIO. The
DP83630 implements all the required MII registers as well as
several optional registers. These registers are fully described
in Section 14.0 Register Block. A description of the serial
management access protocol follows.
www.national.com
26
Turnaround is defined as an idle bit time inserted between the
Register Address field and the Data field. To avoid contention
during a read transaction, no device shall actively drive the
MDIO signal during the first bit of Turnaround. The addressed
DP83630 drives the MDIO with a zero for the second bit of
turnaround and follows this with the required data. Figure 4
shows the timing relationship between MDC and the MDIO as
driven/received by the Station (STA) and the DP83630 (PHY)
for a typical register read access.
For write transactions, the station management entity writes
data to the addressed DP83630 thus eliminating the requirement for MDIO Turnaround. The Turnaround time is filled by
the management entity by inserting <10>. Figure 6 shows the
timing relationship for a typical MII register write access.
TABLE 7. Typical MDIO Frame Format
MII Management Serial Protocol
<idle><start><opcode><device addr><reg addr><turnaround><data><idle>
Read Operation
<idle><01><10><AAAAA><RRRRR><Z0><xxxx xxxx xxxx xxxx><idle>
Write Operation
<idle><01><01><AAAAA><RRRRR><10><xxxx xxxx xxxx xxxx><idle>
30136204
FIGURE 4. Typical MDC/MDIO Read Operation
30136205
FIGURE 5. Typical MDC/MDIO Write Operation
on MDIO in conjunction with a continuous MDC, or the management access made to determine whether Preamble Suppression is supported.
While the DP83630 requires an initial preamble sequence of
32 bits for management initialization, it does not require a full
32-bit sequence between each subsequent transaction. A
minimum of one idle bit between management transactions is
required as specified in the IEEE 802.3u specification.
10.4.3 Serial Management Preamble Suppression
The DP83630 supports a Preamble Suppression mode as indicated by a one in bit 6 of the Basic Mode Status Register
(BMSR, address 01h.) If the station management entity (i.e.
MAC or other management controller) determines that all
PHYs in the system support Preamble Suppression by returning a one in this bit, then the station management entity
need not generate preamble for each management transaction.
The DP83630 requires a single initialization sequence of 32
bits of preamble following hardware/software reset. This requirement is generally met by the mandatory pull-up resistor
10.5 PHY CONTROL FRAMES
The DP83630 supports a packet-based control mechanism
for use in situations where the Serial Management Interface
27
www.national.com
DP83630
order to initialize the MDIO interface, the station management
entity sends a sequence of 32 contiguous logic ones on MDIO
to provide the DP83630 with a sequence that can be used to
establish synchronization. This preamble may be generated
either by driving MDIO high for 32 consecutive MDC clock
cycles, or by simply allowing the MDIO pull-up resistor to pull
the MDIO pin high during which time 32 MDC clock cycles are
provided. In addition 32 MDC clock cycles should be used to
re-sync the device if an invalid Start, Opcode, or turnaround
bit is detected.
The DP83630 waits until it has received this preamble sequence before responding to any other transaction. Once the
DP83630 serial management port has been initialized no further preamble sequencing is required until after a power-on/
reset, invalid Start, invalid Opcode, or invalid turnaround (TA)
bit has occurred.
The Start code is indicated by a <01> pattern. This assures
the MDIO line transitions from the default idle line state.
DP83630
1. PHY Control Frame Read Data
2. Packet Buffer Error
3. Transmit Timestamp
4. Receive Timestamp
5. Trigger Status
6. Event Timestamp
Each of the message types may be individually enabled, allowing options on which functions may be delivered in a PHY
Status Frame.
Timestamps that are delivered via PHY Status Frames will not
be reflected in the corresponding status and timestamp registers nor will they generate an interrupt.
The packet format may be configured to look like a Layer 2
Ethernet frame or a UDP/IPv4 frame.
For a more detailed discussion on the use of PHY Status
Frames, refer to the Software Development Guide for the
DP83630.
is not available or does not provide enough throughput. Application software may build a packet, called a PHY Control
Frame (PCF), to be passed to the PHY through the MAC
Transmit Data interface. The PHY will intercept these packets
and use them to assert writes to Management Registers as if
they occurred via the Management Interface. Multiple register
writes may be incorporated in a single frame.
The PHY Control Frame may also be used to read a register
location. The read value will be returned in a PHY Status
Frame if that function is enabled. Only a single read may be
outstanding at any time, so only one read should be included
in a single PHY Control Frame.
The PHY Control Frame block performs the following functions:
• Parse incoming transmit packets to detect PHY Control
Frames
• Truncate PHY Control Frames to prevent complete frame
from reaching the transmit physical medium
• Buffer up to 15 bytes of the Frame to be intercepted by the
PHY with no portion reaching physical medium
• Detect commands in the PHY Control Frame and pass
them to the register block
• Check CRC to detect error conditions
• Report CRC and invalid command errors to the system via
register status and/or interrupt
PHY Control Frames can be enabled through the PCF_Enable bit in the PHY Control Frames Configuration Register
(PCFCR). PHY Control Frames can also be enabled by using
the PCF_EN strap option. For a more detailed discussion on
the use of PHY Control Frames, refer to the Software Development Guide for the DP83630.
11.0 Architecture
This section describes the operations within each transceiver
module, 100BASE-TX and 10BASE-T. Each operation consists of several functional blocks and is described in the
following:
— 100BASE-TX Transmitter
— 100BASE-TX Receiver
— 100BASE-FX Operation
— 10BASE-T Transceiver Module
11.1 100BASE-TX TRANSMITTER
The 100BASE-TX transmitter consists of several functional
blocks which convert synchronous 4-bit nibble data, as provided by the MII, to a scrambled MLT-3 125 Mb/s serial data
stream. Because the 100BASE-TX TP-PMD is integrated, the
differential output pins, PMD Output Pair, can be directly routed to the magnetics.
The block diagram inFigure 6 provides an overview of each
functional block within the 100BASE-TX transmit section.
The Transmitter section consists of the following functional
blocks:
— Code-Group Encoder and Injection block
— Scrambler block (bypass option)
— NRZ to NRZI Encoder block
— Binary to MLT-3 Converter / Common Driver block
The bypass option for the functional blocks within the
100BASE-TX transmitter provides flexibility for applications
where data conversion is not always required. The DP83630
implements the 100BASE-TX transmit state machine diagram
as specified in the IEEE 802.3u Standard, Clause 24.
10.6 PHY STATUS FRAMES
The DP83630 implements a packet-based status mechanism
that allows the PHY to queue up events and pass them to the
microcontroller through the receive data interface. The packet, called a PHY Status Frame, may be used to provide IEEE
1588 status for transmit packet timestamps, receive packet
timestamps, event timestamps, and trigger conditions. In addition the device can generate status messages indicating
packet buffering errors and to return data read using the PHY
Control Frame register access mechanism.
Each PHY Status Frame may include multiple status messages. The packet will be framed such that it will look like a
IEEE 1588 frame to ensure that it will get to the IEEE 1588
software stack. The PHY will provide buffering of any incoming packet to allow the status packet to be passed to the MAC.
Programmable inter-frame gap and preamble length allow the
PHY to recover lost bandwidth in the case of heavy receive
traffic.
In a PHY Status Frame, status messages are not provided in
a chronological order. Instead, they are provided in the following order of priority:
www.national.com
28
DP83630
30136206
FIGURE 6. 100BASE-TX Transmit Block Diagram
29
www.national.com
DP83630
TABLE 8. 4B5B Code-Group Encoding/Decoding
Name
PCS 5B Code-Group
MII 4B Nibble Code
0
11110
0000
1
01001
0001
2
10100
0010
3
10101
0011
4
01010
0100
5
01011
0101
6
01110
0110
7
01111
0111
8
10010
1000
DATA CODES
9
10011
1001
A
10110
1010
B
10111
1011
C
11010
1100
D
11011
1101
E
11100
1110
F
11101
1111
IDLE AND CONTROL CODES
H
00100
HALT code-group - Error code
I
11111
Inter-Packet IDLE - 0000 (See Note)
J
11000
First Start of Packet - 0101 (See Note)
K
10001
Second Start of Packet - 0101 (See Note)
T
01101
First End of Packet - 0000 (See Note)
R
00111
Second End of Packet - 0000 (See Note)
INVALID CODES
V
00000
V
00001
V
00010
V
00011
V
00101
V
00110
V
01000
V
01100
V
10000
V
11001
Note: Control code-groups I, J, K, T and R in data fields will be mapped as invalid codes, together with RX_ER asserted.
After the T/R code-group pair, the code-group encoder continuously injects IDLEs into the transmit data stream until the
next transmit packet is detected (reassertion of Transmit Enable).
11.1.1 Code-Group Encoding and Injection
The code-group encoder converts 4-bit (4B) nibble data generated by the MAC into 5-bit (5B) code-groups for transmission. This conversion is required to allow control data to be
combined with packet data code-groups. Refer to Table 8 for
4B to 5B code-group mapping details.
The code-group encoder substitutes the first 8-bits of the
MAC preamble with a J/K code-group pair (11000 10001) upon transmission. The code-group encoder continues to replace subsequent 4B preamble and data nibbles with
corresponding 5B code-groups. At the end of the transmit
packet, upon the deassertion of Transmit Enable signal from
the MAC, the code-group encoder injects the T/R code-group
pair (01101 00111) indicating the end of the frame.
www.national.com
11.1.2 Scrambler
The scrambler is required to control the radiated emissions at
the media connector and on the twisted pair cable (for
100BASE-TX applications). By scrambling the data, the total
energy launched onto the cable is randomly distributed over
a wide frequency range. Without the scrambler, energy levels
at the PMD and on the cable could peak beyond FCC limitations at frequencies related to repeating 5B sequences (i.e.,
continuous transmission of IDLEs).
30
data stream to synchronous 4-bit nibble data that is provided
to the MII. Because the 100BASE-TX TP-PMD is integrated,
the differential input pins, RD±, can be directly routed from
the AC coupling magnetics.
See Figure 7 for a block diagram of the 100BASE-TX receive
function. This provides an overview of each functional block
within the 100BASE-TX receive section.
The Receive section consists of the following functional
blocks:
— Analog Front End
— Input and BLW Compensation
— Signal Detect
— Digital Adaptive Equalization
— MLT-3 to Binary Decoder
— Clock Recovery Module
— NRZI to NRZ Decoder
— Serial to Parallel
— Descrambler (bypass option)
— Code Group Alignment
— 4B/5B Decoder
— Link Integrity Monitor
— Bad SSD Detection
11.1.3 NRZ to NRZI Encoder
After the transmit data stream has been serialized and scrambled, the data must be NRZI encoded in order to comply with
the TP-PMD standard for 100BASE-TX transmission over
Category-5 Unshielded twisted pair cable. There is no ability
to bypass this block within the DP83630. The NRZI data is
sent to the 100 Mb Driver. In addition, this module creates an
encoded MLT value for use in 100 Mb Internal Loopback.
11.1.4 Binary to MLT-3 Convertor
The Binary to MLT-3 conversion is accomplished by converting the serial binary data stream output from the NRZI encoder into two binary data streams with alternately phased
logic one events. These two binary streams are then fed to
the twisted pair output driver which converts the voltage to
current and alternately drives either side of the transmit transformer primary winding, resulting in a minimal current MLT-3
signal.
The 100BASE-TX MLT-3 signal sourced by the PMD Output
Pair common driver is slew rate controlled. This should be
considered when selecting AC coupling magnetics to ensure
TP-PMD Standard compliant transition times (3 ns < Tr < 5
ns).
The 100BASE-TX transmit TP-PMD function within the
DP83630 is capable of sourcing only MLT-3 encoded data.
Binary output from the PMD Output Pair is not possible in 100
Mb/s mode.
11.2.1 Analog Front End
In addition to the Digital Equalization and Gain Control, the
DP83630 includes Analog Equalization and Gain Control in
the Analog Front End. The Analog Equalization reduces the
amount of Digital Equalization required in the DSP.
11.2.2 Digital Signal Processor
The Digital Signal Processor includes Base Line Wander
Compensation and Adaptive Equalization with Gain Control.
11.2 100BASE-TX RECEIVER
The 100BASE-TX receiver consists of several functional
blocks which convert the scrambled MLT-3 125 Mb/s serial
31
www.national.com
DP83630
The scrambler is configured as a closed loop linear feedback
shift register (LFSR) with an 11-bit polynomial. The output of
the closed loop LFSR is X-ORd with the serial NRZ data from
the code-group encoder. The result is a scrambled data
stream with sufficient randomization to decrease radiated
emissions at certain frequencies by as much as 20 dB. The
DP83630 uses the PHY_ID (pins PHYAD [4:0]) to set a
unique seed value.
DP83630
30136211
FIGURE 7. 100BASE-TX Receive Block Diagram
stage. This enables the receive 'eye pattern' to be opened
sufficiently to allow very reliable data recovery.
11.2.2.1 Base Line Wander Compensation
The DP83630 is completely ANSI TP-PMD compliant and includes Base Line Wander (BLW) compensation. The BLW
compensation block can successfully recover the TP-PMD
defined “killer” pattern.
11.2.3 Signal Detect
The signal detect function of the DP83630 is incorporated to
meet the specifications mandated by the ANSI FDDI TP-PMD
Standard as well as the IEEE 802.3 100BASE-TX Standard
for both voltage thresholds and timing parameters.
Note that the reception of normal 10BASE-T link pulses and
fast link pulses per IEEE 802.3u Auto-Negotiation by the
100BASE-TX receiver do not cause the DP83630 to assert
signal detect.
11.2.2.2 Digital Adaptive Equalization and Gain Control
The DP83630 utilizes an extremely robust equalization
scheme referred as ‘Digital Adaptive Equalization.’
The Digital Equalizer removes ISI (inter symbol interference)
from the receive data stream by continuously adapting to provide a filter with the inverse frequency response of the channel. Equalization is combined with an adaptive gain control
www.national.com
32
11.2.5 Clock Recovery Module
The Clock Recovery function is implemented as a Phase detector and Loop Filter which accepts data and error from the
receive datapath to detect the phase of the recovered data.
This phase information is fed into the loop filter to determine
an 8-bit signed frequency control. The 8-bit signed frequency
control is sent to the FCO in the Analog Front End to derive
the receive clock. The extracted and synchronized clock and
data are used as required by the synchronous receive operations as generally depicted in Figure 7.
11.2.10 4B/5B Decoder
The code-group decoder functions as a look up table that
translates incoming 5B code-groups into 4B nibbles. The
code-group decoder first detects the J/K code-group pair preceded by IDLE code-groups and replaces the J/K with MAC
preamble. Specifically, the J/K 10-bit code-group pair is replaced by the nibble pair (0101 0101). All subsequent 5B
code-groups are converted to the corresponding 4B nibbles
for the duration of the entire packet. This conversion ceases
upon the detection of the T/R code-group pair denoting the
End of Stream Delimiter (ESD) or with the reception of a minimum of two IDLE code-groups.
11.2.6 NRZI to NRZ Decoder
In a typical application, the NRZI to NRZ decoder is required
in order to present NRZ formatted data to the descrambler (or
to the code-group alignment block if the descrambler is bypassed).
11.2.11 100BASE-TX Link Integrity Monitor
The 100BASE-TX link monitor ensures that a valid and stable
link is established before enabling both the Transmit and Receive PCS layer.
Signal detect must be valid for 395 µs to allow the link monitor
to enter the 'Link Up' state and enable the transmit and receive
functions.
11.2.7 Serial to Parallel
The 100BASE-TX receiver includes a Serial to Parallel converter which supplies 5-bit wide data symbols to the PCS Rx
state machine.
11.2.8 Descrambler
A serial descrambler is used to de-scramble the received NRZ
data. The descrambler has to generate an identical data
scrambling sequence (N) in order to recover the original unscrambled data (UD) from the scrambled data (SD) as represented in the equations:
11.2.12 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition
from consecutive idle code-groups to non-idle code-groups
which is not prefixed by the code-group pair /J/K.
If this condition is detected, the DP83630 will assert RX_ER
and present RXD[3:0] = 1110 to the MII for the cycles that
correspond to received 5B code-groups until at least two IDLE
code-groups are detected. In addition, the False Carrier
Sense Counter register (FCSCR) will be incremented by one.
Once at least two IDLE code-groups are detected, RX_ER
and CRS become de-asserted.
30136251
Synchronization of the descrambler to the original scrambling
sequence (N) is achieved based on the knowledge that the
incoming scrambled data stream consists of scrambled IDLE
data. After the descrambler has recognized 12 consecutive
IDLE code-groups, where an unscrambled IDLE code-group
in 5B NRZ is equal to five consecutive ones (11111), it will
synchronize to the receive data stream and generate unscrambled data in the form of unaligned 5B code-groups.
In order to maintain synchronization, the descrambler must
continuously monitor the validity of the unscrambled data that
it generates. To ensure this, a line state monitor and a hold
timer are used to constantly monitor the synchronization status. Upon synchronization of the descrambler, the hold timer
starts a 722 µs countdown. Upon detection of sufficient IDLE
code-groups (58 bit times) within the 722 µs period, the hold
timer will reset and begin a new countdown. This monitoring
operation will continue indefinitely given a properly operating
network connection with good signal integrity. If the line state
monitor does not recognize sufficient unscrambled IDLE
code-groups within the 722 µs period, the entire descrambler
will be forced out of the current state of synchronization and
reset in order to re-acquire synchronization. The DP83604T
also provides a bit (DESC_TIME, bit 7) in the PCSR register
(0x16) that increases the descrambler timeout from 722 µs to
2 ms to allow reception of packets up to 9kB in size without
losing descrambler lock.
11.3 100BASE-FX OPERATION
The DP83630 provides IEEE 802.3 compliant 100BASE-FX
operation. Configuration of FX mode is via strap option, or
through the register interface.
11.3.1 100BASE-FX Transmit
In 100BASE-FX mode, the device Transmit pins connect to
an industry standard Fiber Transceiver with PECL signaling
through a capacitively coupled circuit.
In FX mode, the device bypasses the Scrambler and the
MLT3 encoder. This allows for the transmission of serialized
5B4B encoded NRZI data at 125 MHz.
The only added functionality from 100BASE-TX is the support
for Far-End Fault data generation.
11.3.2 100BASE-FX Receive
In 100BASE-FX mode, the device Receive pins connect to an
industry standard Fiber Transceiver with PECL signaling
through a capacitively coupled circuit.
In FX mode, the device bypasses the MLT3 Decoder and the
Descrambler. This allows for the reception of serialized 5B4B
encoded NRZI data at 125 MHz.
The only added functionality for 100BASE-FX from
100BASE-TX is the support of Far-End Fault detection.
11.2.9 Code-Group Alignment
The code-group alignment module operates on unaligned 5bit data from the descrambler (or, if the descrambler is by-
33
www.national.com
DP83630
passed, directly from the NRZI/NRZ decoder) and converts it
into 5B code-group data (5 bits). Code-group alignment occurs after the J/K code-group pair is detected. Once the J/K
code-group pair (11000 10001) is detected, subsequent data
is aligned on a fixed boundary.
11.2.4 MLT-3 to Binary Decoder
The DP83630 decodes the MLT-3 information from the Digital
Adaptive Equalizer block to binary NRZI data.
DP83630
signal. The DP83630's 10 Mb/s ENDEC is designed to encode and decode simultaneously.
11.3.3 Far-End Fault
Since 100BASE-FX does not support Auto-Negotiation, a
Far-End Fault facility is included which allows for detection of
link failures.
When no signal is being received as determined by the Signal
Detect function, the device sends a Far-End Fault indication
to the far-end peer. The Far-End Fault indication is comprised
of 3 or more repeating cycles, each consisting of 84 one’s
followed by 1 zero. The pattern is such that it will not satisfy
the 100BASE-X carrier sense mechanism, but is easily detected as the Fault indication. The pattern will be transparent
to devices that do not support Far-End Fault.
The Far-End Fault detection process continuously monitors
the receive data stream for the Far-End Fault indication.
When detected, the Link Monitor is forced to deassert Link
status. This causes the device to transmit IDLE’s on its transmit path.
11.4.2 Smart Squelch
The smart squelch is responsible for determining when valid
data is present on the differential receive inputs. The
DP83630 implements an intelligent receive squelch to ensure
that impulse noise on the receive inputs will not be mistaken
for a valid signal. Smart squelch operation is independent of
the 10BASE-T operational mode.
The squelch circuitry employs a combination of amplitude and
timing measurements (as specified in the IEEE 802.3
10BASE-T standard) to determine the validity of data on the
twisted pair inputs (refer to Figure 8).
The signal at the start of a packet is checked by the smart
squelch and any pulses not exceeding the squelch level (either positive or negative, depending upon polarity) will be
rejected. Once this first squelch level is overcome correctly,
the opposite squelch level must then be exceeded within 150
ns. Finally the signal must again exceed the original squelch
level within 150 ns to ensure that the input waveform will not
be rejected. This checking procedure results in the loss of
typically three preamble bits at the beginning of each packet.
Only after all these conditions have been satisfied will a control signal be generated to indicate to the remainder of the
circuitry that valid data is present. At this time, the smart
squelch circuitry is reset.
Valid data is considered to be present until the squelch level
has not been generated for a time longer than 150 ns, indicating the End of Packet. Once good data has been detected,
the squelch levels are reduced to minimize the effect of noise
causing premature End of Packet detection.
The receive squelch threshold level can be lowered for use in
longer cable or STP applications. This is achieved by configuring the SQUELCH bits (11:9) in the 10BTSCR register
(0x1A).
11.4 10BASE-T TRANSCEIVER MODULE
The 10BASE-T Transceiver Module is IEEE 802.3 compliant.
It includes the receiver, transmitter, collision, heartbeat, loopback, jabber, and link integrity functions, as defined in the
standard. An external filter is not required on the 10BASE-T
interface since this is integrated inside the DP83630. This
section focuses on the general 10BASE-T system level operation.
11.4.1 Operational Modes
The DP83630 has two basic 10BASE-T operational modes:
— Half Duplex mode
— Full Duplex mode
Half Duplex Mode
In Half Duplex mode the DP83630 functions as a standard
IEEE 802.3 10BASE-T transceiver supporting the CSMA/CD
protocol.
Full Duplex Mode
In Full Duplex mode the DP83630 is capable of simultaneously transmitting and receiving without asserting the collision
30136209
FIGURE 8. 10BASE-T Twisted Pair Smart Squelch Operation
Collisions are reported by the COL signal on the MII. Collisions are also reported when a jabber condition is detected.
11.4.3 Collision Detection and SQE
When in Half Duplex, a 10BASE-T collision is detected when
the receive and transmit channels are active simultaneously.
www.national.com
34
11.4.8 Transmit and Receive Filtering
External 10BASE-T filters are not required when using the
DP83630, as the required signal conditioning is integrated into the device.
Only isolation transformers and impedance matching resistors are required for the 10BASE-T transmit and receive
interface. The internal transmit filtering ensures that all the
harmonics in the transmit signal are attenuated by at least
30 dB.
11.4.9 Transmitter
The encoder begins operation when the Transmit Enable input (TX_EN) goes high and converts NRZ data to pre-emphasized Manchester data for the transceiver. For the
duration of TX_EN, the serialized Transmit Data (TXD) is encoded for the transmit-driver pair (PMD Output Pair). TXD
must be valid on the rising edge of Transmit Clock (TX_CLK).
Transmission ends when TX_EN de-asserts. The last transition is always positive; it occurs at the center of the bit cell if
the last bit is a one, or at the end of the bit cell if the last bit is
a zero.
11.4.4 Carrier Sense
Carrier Sense (CRS) may be asserted due to receive activity
once valid data is detected via the squelch function.
For 10 Mb/s Half Duplex operation, CRS is asserted during
either packet transmission or reception.
For 10 Mb/s Full Duplex operation, CRS is asserted only during receive activity.
CRS is deasserted following an end of packet.
11.4.5 Normal Link Pulse Detection/Generation
The link pulse generator produces pulses as defined in the
IEEE 802.3 10BASE-T standard. Each link pulse is nominally
100 ns in duration and transmitted every 16 ms in the absence
of transmit data.
Link pulses are used to check the integrity of the connection
with the remote end. If valid link pulses are not received, the
link detector disables the 10BASE-T twisted pair transmitter,
receiver and collision detection functions.
When the link integrity function is disabled (FORCE_LINK_10
of the 10BTSCR register), a good link is forced and the
10BASE-T transceiver will operate regardless of the presence of link pulses.
11.4.10 Receiver
The decoder consists of a differential receiver and a PLL to
separate a Manchester encoded data stream into internal
clock signals and data. The differential input must be externally terminated with a differential 100 Ω termination network
to accommodate UTP cable.
The decoder detects the end of a frame when no additional
mid-bit transitions are detected. Within one and a half bit times
after the last bit, carrier sense is de-asserted. Receive clock
stays active for five more bit times after CRS goes low, to
guarantee the receive timings of the controller.
11.4.6 Jabber Function
The jabber function monitors the DP83630's output and disables the transmitter if it attempts to transmit a packet of
longer than legal size. A jabber timer monitors the transmitter
and disables the transmission if the transmitter is active for
approximately 85 ms.
Once disabled by the Jabber function, the transmitter stays
disabled for the entire time that the ENDEC module's internal
transmit enable is asserted. This signal has to be de-asserted
for approximately 500 ms (the “unjab” time) before the Jabber
function re-enables the transmit outputs.
The Jabber function is only relevant in 10BASE-T mode.
The DP83630 includes an internal power-on reset (POR)
function and does not need to be explicitly reset for normal
operation after power up. If required during normal operation,
the device can be reset by a hardware or software reset.
12.0 Reset Operation
12.1 HARDWARE RESET
A hardware reset is accomplished by applying a low pulse
(TTL level), with a duration of at least 1 µs, to the RESET_N
pin. This will reset the device such that all registers will be
reinitialized to default values and the hardware configuration
values will be re-latched into the device (similar to the powerup/reset operation).
12.2 FULL SOFTWARE RESET
A full-chip software reset is accomplished by setting the RESET bit (bit 15) of the Basic Mode Control Register (BMCR).
The period from the point in time when the reset bit is set to
the point in time when software reset has concluded is approximately 1 µs.
The software reset will reset the device such that all registers
will be reset to default values and the hardware configuration
values will be maintained. Software driver code must wait 3
µs following a software reset before allowing further serial MII
operations with the DP83630.
11.4.7 Automatic Link Polarity Detection and Correction
The DP83630's 10BASE-T transceiver module incorporates
an automatic link polarity detection circuit. When three consecutive inverted link pulses are received, bad polarity is
reported. The bad polarity condition is latched in the
10BTSCR register.
The DP83630's 10BASE-T transceiver module corrects for
this error internally and will continue to decode received data
correctly. This eliminates the need to correct the wiring error
immediately.
A polarity reversal can be caused by a wiring error at either
end of the cable, usually at the Main Distribution Frame (MDF)
or patch panel in the wiring closet.
12.3 SOFT RESET
A partial software reset can be initiated by setting the
SOFT_RESET bit (bit 9) in the PHYCR2 Register. Setting this
bit will reset all transmit and receive operations, but will not
reset the register space. All register configurations will be
35
www.national.com
DP83630
The COL signal remains set for the duration of the collision.
If the ENDEC is receiving when a collision is detected it is
reported immediately (through the COL pin).
When heartbeat is enabled, approximately 1 µs after the
transmission of each packet, a Signal Quality Error (SQE)
signal of approximately 10-bit times is generated to indicate
successful transmission. SQE is reported as a pulse on the
COL signal of the MII.
The SQE test is inhibited when the PHY is set in full duplex
mode. SQE can also be inhibited by setting the
HEARTBEAT_DIS bit (1) in the 10BTSCR register (0x1A).
DP83630
preserved. Register space will remain available following a
soft reset.
Below is a partial list of recommended transformers. It is important that the user realize that variations with PCB and
component characteristics requires that the application be
tested to ensure that the circuit meets the requirements of the
intended application.
Pulse H1102
Pulse H2019
12.4 PTP RESET
The entire PTP function, including the IEEE 1588 clock, associated logic, and PTP register space (with two exceptions),
can be reset via the PTP_RESET bit in the PTP_CTL register.
The PTP_COC and PTP_CLKSRC registers are not reset in
order to preserve the nominal operation of the clock output.
13.0 Design Guidelines
13.1 TPI NETWORK CIRCUIT
Figure 9 shows the recommended circuit for a 10/100 Mb/s
twisted pair interface.
30136210
FIGURE 9. 10/100 Mb/s Twisted Pair Interface
www.national.com
36
DP83630
13.2 FIBER NETWORK CIRCUIT
Figure 10 shows the recommended circuit for a 100 Mb/s fiber
pair interface.
30136212
FIGURE 10. 100 Mb/s Fiber Pair Interface
13.3 ESD PROTECTION
Typically, ESD precautions are predominantly in effect when
handling the devices or board before being installed in a system. In those cases, strict handling procedures need be implemented during the manufacturing process to greatly
reduce the occurrences of catastrophic ESD events. After the
system is assembled, internal components are less sensitive
from ESD events.
The network interface pins are more susceptible to ESD
events.
Oscillator
If an external clock source is used, X1 should be tied to the
clock source and X2 should be left floating.
The CMOS 25 MHz oscillator specifications for MII Mode are
listed in Table 9. For RMII Slave Mode, the CMOS 50 MHz
oscillator specifications are listed in Table 10. For RMII Slave
mode, it is not recommended that the system clock out, Pin
24, be used as the reference clock to the MAC without first
verifying the interface timing. See AN-1405 for more details.
Crystal
A 25 MHz, parallel, 20 pF load crystal resonator should be
used if a crystal source is desired. Figure 11 shows a typical
connection for a crystal resonator circuit. The load capacitor
values will vary with the crystal vendors; check with the vendor for the recommended loads.
The oscillator circuit is designed to drive a parallel resonance
AT cut crystal with a minimum drive level of 100 µW and a
13.4 CLOCK IN (X1) RECOMMENDATIONS
The DP83630 supports an external CMOS level oscillator
source or a crystal resonator device.
37
www.national.com
DP83630
maximum of 500 µW. If a crystal is specified for a lower drive
level, a current limiting resistor should be placed in series between X2 and the crystal.
As a starting point for evaluating an oscillator circuit, if the
requirements for the crystal are not known, CL1 and CL2
should be set at 33 pF, and R1 should be set at 0 Ω.
Specification for 25 MHz crystal are listed in Table 11.
30136213
FIGURE 11. Crystal Oscillator Circuit
TABLE 9. 25 MHz Oscillator Specification
Parameter
Min
Frequency
Typ
Max
25
Units
Condition
MHz
Frequency Tolerance
±50
ppm
Operational Temperature
Frequency Stability
±50
ppm
1 year aging
Rise / Fall Time
6
nsec
20% - 80%
Jitter
800 (Note 2)
psec
Short term
Jitter
800 (Note 2)
psec
Long term
Symmetry
40%
60%
Duty Cycle
Note 2: This limit is provided as a guideline for component selection and not guaranteed by production testing. Refer to AN-1548, “PHYTER 100 Base-TX
Reference Clock Jitter Tolerance,” for details on jitter performance.
TABLE 10. 50 MHz Oscillator Specification
Parameter
Min
Frequency
Typ
Max
50
±50
Frequency Stability
Rise / Fall Time
Jitter
Jitter
40%
Condition
MHz
Frequency Tolerance
Symmetry
Units
ppm
Operational Temperature
±50
ppm
Operational Temperature
6
nsec
20% - 80%
800 (Note 3)
psec
Short term
800 (Note 3)
psec
60%
Long term
Duty Cycle
Note 3: This limit is provided as a guideline for component selection and not guaranteed by production testing. Refer to AN-1548, “PHYTER 100 Base-TX
Reference Clock Jitter Tolerance,” for details on jitter performance.
TABLE 11. 25 MHz Crystal Specification
Parameter
Min
Frequency
Typ
Max
25
Units
Condition
MHz
Frequency Tolerance
±50
ppm
Operational Temperature
Frequency Stability
±50
ppm
1 year aging
40
pF
Range of CL1and CL2
Shunt Capacitance
www.national.com
25
38
DP83630
14.0 Register Block
TABLE 12. Register Map
Offset
Access
Tag
0
RW
BMCR
Basic Mode Control Register
1
RO
BMSR
Basic Mode Status Register
02h
2
RO
PHYIDR1
PHY Identifier Register #1
03h
3
RO
PHYIDR2
PHY Identifier Register #2
04h
4
RW
ANAR
05h
5
RW
ANLPAR
06h
6
RW
ANER
07h
7
RW
ANNPTR
08h-0Fh
8-15
10h
16
RO
PHYSTS
11h
17
RW
MICR
MII Interrupt Control Register
12h
18
RW
MISR
MII Interrupt Status and Event Control Register
13h
19
RW
PAGESEL
Hex
Decimal
00h
01h
RESERVED
Description
Auto-Negotiation Advertisement Register
Auto-Negotiation Link Partner Ability Register
Auto-Negotiation Expansion Register
Auto-Negotiation Next Page TX Register
RESERVED
PHY Status Register
Page Select Register
Extended Registers - Page 0
14h
20
RO
FCSCR
15h
16h
False Carrier Sense Counter Register
21
RO
RECR
Receive Error Counter Register
22
RW
PCSR
PCS Sub-Layer Configuration and Status Register
17h
23
RW
RBR
18h
24
RW
LEDCR
LED Direct Control Register
PHY Control Register
RMII and Bypass Register
19h
25
RW
PHYCR
1Ah
26
RW
10BTSCR
10Base-T Status/Control Register
1Bh
27
RW
CDCTRL1
CD Test Control Register and BIST Extensions Register
1Ch
28
RW
PHYCR2
PHY Control Register 2
1Dh
29
RW
EDCR
1Eh
30
1Fh
31
RESERVED
RW
PCFCR
Energy Detect Control Register
RESERVED
PHY Control Frames Configuration Register
Test Registers - Page 1
14h - 1Dh
20 - 29
1Eh
30
1Fh
31
RESERVED
RW
SD_CNFG
RESERVED
RESERVED
Signal Detect Configuration
RESERVED
Link Diagnostics Registers - Page 2
14h
20
RO
15h
21
RW
FREQ100
16h
22
RW
TDR_CTRL
TDR Control Register
17h
23
RW
TDR_WIN
TDR Window Register
18h
24
RO
TDR_PEAK
19h
25
RO
TDR_THR
TDR Threshold Measurement Register
1Ah
26
RW
VAR_CTRL
Variance Control Register
RO
1Bh
27
1Ch
28
1Dh
29
RW
1Eh
30
1Fh
31
LEN100_DET
VAR_DAT
RESERVED
100 Mb Length Detect Register
100 Mb Frequency Offset Indication Register
TDR Peak Measurement Register
Variance Data Register
RESERVED
LQMR
Link Quality Monitor Register
RW
LQDR
Link Quality Data Register
RW
LQMR2
Link Quality Monitor Register 2
Reserved Registers - Page 3
14h - 1Fh
20 - 31
RESERVED
RESERVED
PTP 1588 Base Registers - Page 4
39
www.national.com
DP83630
Offset
Access
Tag
Description
Hex
Decimal
14h
20
RW
PTP_CTL
PTP Control Register
15h
21
RW
PTP_TDR
PTP Time Data Register
16h
22
RW
PTP_STS
PTP Status Register
17h
23
RW
PTP_TSTS
18h
24
RW
PTP_RATEL
PTP Rate Low Register
19h
25
RW
PTP_RATEH
PTP Rate High Register
1Ah
26
RO
PTP_RDCKSUM
PTP Page 4 Read Checksum
1Bh
27
RO
PTP_WRCKSUM
PTP Page 4 Write Checksum
1Ch
28
RO
PTP_TXTS
PTP Transmit TimeStamp Register
1Dh
29
RO
PTP_RXTS
PTP Receive TimeStamp Register
1Eh
30
RO
PTP_ESTS
PTP Event Status Register
1Fh
31
RO
PTP_EDATA
14h
20
RW
PTP_TRIG
PTP Trigger Configuration Register
15h
21
RW
PTP_EVNT
PTP Event Configuration Register
16h
22
RW
PTP_TXCFG0
PTP Transmit Configuration Register 0
17h
23
RW
PTP_TXCFG1
PTP Transmit Configuration Register 1
18h
24
RW
PSF_CFG0
19h
25
RW
PTP_RXCFG0
PTP Receive Configuration Register 0
1Ah
26
RW
PTP_RXCFG1
PTP Receive Configuration Register 1
1Bh
27
RW
PTP_RXCFG2
PTP Receive Configuration Register 2
1Ch
28
RW
PTP_RXCFG3
PTP Receive Configuration Register 3
1Dh
29
RW
PTP_RXCFG4
PTP Receive Configuration Register 4
1Eh
30
RW
PTP_TRDL
PTP Temporary Rate Duration Low Register
1Fh
31
RW
PTP_TRDH
PTP Temporary Rate Duration High Register
14h
20
RW
PTP_COC
PTP Clock Output Control Register
15h
21
RW
PSF_CFG1
PHY Status Frames Configuration Register 1
16h
22
RW
PSF_CFG2
PHY Status Frames Configuration Register 2
17h
23
RW
PSF_CFG3
PHY Status Frames Configuration Register 3
18h
24
RW
PSF_CFG4
PHY Status Frames Configuration Register 4
19h
25
RW
PTP_SFDCFG
1Ah
26
RW
PTP_INTCTL
PTP Interrupt Control Register
1Bh
27
RW
PTP_CLKSRC
PTP Clock Source Register
1Ch
28
RW
PTP_ETR
PTP Ethernet Type Register
1Dh
29
RW
PTP_OFF
PTP Offset Register
1Eh
30
RO
PTP_GPIOMON
PTP GPIO Monitor Register
1Fh
31
RW
PTP_RXHASH
PTP Receive Hash Register
PTP Trigger Status Register
PTP Event Data Register
PTP 1588 Configuration Registers - Page 5
PHY Status Frames Configuration Register 0
PTP 1588 Configuration Registers - Page 6
www.national.com
PTP SFD Configuration Register
40
www.national.com
02h
03h
04h
05h
PHY Identifier
Register #1
PHY Identifier
Register #2
Auto-Negotiation
Advertisement
Register
Auto-Negotiation
Link Partner Ability
Register (Base
Page)
ANNPTR
Auto-Negotiation
Next Page TX
Register
14h
15h
16h
False Carrier
Sense Counter
Register
Receive Error
Counter Register
PCS Sub-Layer
Configuration and
Status Register
18h
13h
Page Select
Register
LED Direct Control
Register
Reserved
MII Interrupt Status 12h
and Misc. Control
Register
17h
MISR
11h
MII Interrupt
Control Register
RMII and Bypass
Register
MICR
10h
PHY Status
Register
LEDCR
RBR
PCSR
RECR
FCSCR
PHYSTS
08-0fh
RESERVED
Reserved
ANER
Auto-Negotiation
06h
Expansion Register
07h
ANLPARN
P
Auto-Negotiation
05h
Link Partner Ability
Register Next Page
ANLPAR
ANAR
PHYIDR2
PHYIDR1
BMSR
01h
Basic Mode Status
Register
Tag
BMCR
Addr
Basic Mode Control 00h
Register
Register Name
Reserved
Reserved
AUTO_CR
OSSOVE
R
Reserved
Reserved
Reserved
LQ_INT
Reserved
Reserved
Reserved
Next Page
Ind
Reserved
Next Page
Ind
Next Page
Ind
Next Page
Ind
OUI LSB
OUI MSB
100BaseT4
Reset
Bit 15
Reserved
Reserved
Reserved
Reserved
LINK_INT
Reserved
Rx Err
Latch
Reserved
Message
Page
Reserved
Message
Page
Remote
Fault
Remote
Fault
OUI LSB
OUI MSB
100BaseTX HDX
Speed
Selection
Bit 13
Reserved
Reserved
Reserved
Reserved
SPD_INT
or
SPD_DUP
_INT
Reserved
Polarity
Status
Reserved
ACK2
Reserved
ACK2
Reserved
Reserved
OUI LSB
FREE_CL
K
Reserved
Reserved
Reserved
DUP_INT
or
PTP_INT
Reserved
False
Carrier
Sense
Reserved
TOG_TX
Reserved
Toggle
ASM_DIR
ASM_DIR
OUI LSB
OUI MSB
HDX
OUI MSB
10Base-T
FDX
Power
Down
Bit 11
10Base-T
Auto-Neg
Enable
Bit 12
Reserved
Reserved
Reserved
DIS_SPDL
ED
RMII_MAS DIS_TX_O RX_PORT RX_PORT
TER
PT
Reserved
Reserved
Reserved
Reserved
ED_INT
Reserved
MDIX
mode
Reserved
Reserved
Reserved
ACK
ACK
Reserved
OUI LSB
OUI MSB
100BaseTX FDX
Loopback
Bit 14
Bit 9
Bit 8
Reserved
FHF_INT
or
CTR_INT
Reserved
Descrambl
er Lock
Reserved
CODE
Reserved
Code
T4
Reserved
RHF_INT
or
PCF_INT
Reserved
Receive
Page
Reserved
CODE
Reserved
Code
TX_FD
TX_FD
MDL
T4
VNDR_
MDL
OUI MSB
Reserved
Duplex
Mode
VNDR_
OUI MSB
Reserved
Restart
Auto-Neg
DIS_LNKL
ED
TX_SOUR
CE
TQ_EN
Reserved
Reserved
DIS_ACTL
ED
TX_SOUR
CE
SD_FORC
E_PMA
Reserved
Reserved
LEDACT_
RX
PMD_LOO
P
OPTION
SD_
Reserved
Reserved
EXTENDED REGISTERS - PAGE 0
Reserved
ANC_INT
Reserved
Signal
Detect
Reserved
CODE
Reserved
Code
PAUSE
PAUSE
OUI LSB
OUI MSB
Reserved
Isolate
Bit 10
TABLE 13. Register Table
Bit 7
BLINK_FR
EQ
SCMII_RX
DESC_TIM
E
RXERCNT
FCSCNT
Reserved
LQ_INT_E
N
Reserved
MII
Interrupt
Reserved
CODE
Reserved
Code
TX
TX
MDL
VNDR_
OUI MSB
Unidirectio
nal Ability
Collision
Test
Bit 6
BLINK_FR
EQ
SCMII_TX
FX_EN
RXERCNT
FCSCNT
Reserved
ED_INT_E
N
Reserved
Remote
Fault
Reserved
CODE
Reserved
Code
10_FD
10_FD
MDL
VNDR_
OUI MSB
MF
Preamble
Suppress
Reserved
Bit 5
DRV_SPDL
ED
RMII_MOD
E
100_OK
FORCE_
RXERCNT
FCSCNT
Reserved
LINK_INT_
EN
Reserved
Jabber
Detect
Reserved
CODE
Reserved
Code
10
10
MDL
VNDR_
OUI MSB
Complete
Auto-Neg
Reserved
Bit 4
Bit 3
DRV_LNKL
ED
Bit 2
FEFI_EN
RXERCNT
FCSCNT
Reserved
DUP_INT_E
N
PTP_INT_S
EL
Loopback
Status
Reserved
CODE
DRV_ACTL
ED
SPDLED
RX_UNF_S
TS
BYPASS
NRZI_
RXERCNT
FCSCNT
Page_Sel
Bit
ANC_INT_
EN
TINT
Duplex
Status
Reserved
CODE
NP_
ABLE
ABLE
Code
Protocol
Selection
Protocol
Selection
REV
MDL_
OUI MSB
Status
Link
Reserved
LP_NP_
Code
Protocol
Selection
Protocol
Selection
REV
MDL_
OUI MSB
Ability
Auto-Neg
Reserved
RMII_REV1 RX_OVF_S
_0
TS
Reserved
RXERCNT
FCSCNT
Reserved
SPED_INT
_EN
Reserved
Complete
Auto-Neg
Reserved
CODE
PDF
Code
Protocol
Selection
Protocol
Selection
MDL
VNDR_
OUI MSB
Remote
Fault
Reserved
Bit 1
Bit 0
INT_OE
Status
Link
Reserved
CODE
ABLE
LP_AN_
Code
Protocol
Selection
Protocol
Selection
REV
MDL_
OUI MSB
Extended
Capability
Reserved
LNKLED
ELAST_BU
F
BYPASS
SCRAM_
RXERCNT
FCSCNT
Page_Sel
Bit
ACTLED
ELAST_B
UF
SCRAM_
BYPASS
DE
RXERCN
T
FCSCNT
Page_Sel
Bit
FHF_INT_E RHF_INT
N
_EN
or
or
CTR_INT_E PCF_INT_
N
EN
INTEN
Speed
Status
Reserved
CODE
RX
PAGE_
Code
Protocol
Selection
Protocol
Selection
REV
MDL_
OUI MSB
Jabber
Detect
Reserved
DP83630
41
www.national.com
42
1Ch
1Dh
1Eh
1Fh
14h-1Dh
1Eh
1Fh
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
PHY Control
Register 2
Energy Detect
Control Register
RESERVED
PHY Control
Frames
Configuration
Register
RESERVED
Signal Detect
Configuration
Register
RESERVED
100 Mb Length
Detect Register
100 Mb Frequency
Offset Indication
Register
TDR Control
Register
TDR Window
Register
TDR Peak
Measurement
Register
TDR Threshold
Measurement
Register
Variance Control
Register
Variance Data
Register
Reserved
Reserved
VAR_DAT
A
VAR_CTR
L
TDR_THR
TDR_PEA
K
TDR_WIN
TDR_CTR
L
FREQ100
LEN100_D
ET
Reserved
SD_CNFG
Reserved
PCFCR
Reserved
EDCR
PHYCR2
CDCTRL1
Link Quality Monitor 1Fh
Register 2
1Eh
LQMR2
LQDR
1Bh
CD Test Control
and BIST
Extensions
Register
10BTSCR
Link Quality Data
Register
1Ah
10Base-T Status/
Control Register
PHYCR
Tag
LQMR
19h
PHY Control
Register
Link Quality Monitor 1Dh
Register
Addr
Register Name
Bit 15
Bit 14
Bit 13
Reserved
Reserved
FORCE_M PAUSE_R
DIX
X
Bit 12
Reserved
PAUSE_T
X
Bit 11
Bit 10
PSR_15
SQUELCH SQUELCH
BIST_FE
Bit 9
SQUELCH
STATUS
BIST_
Bit 8
LOOPBAC
K_10_DIS
BIST_STA
RT
Reserved
Reserved
SYNC_EN
ET_EN
Reserved
VAR_DAT
A
Reserved
Reserved
Reserved
TDR_STA
RT
TDR_100
Mb
Reserved
Reserved
Reserved
Reserved
Reserved
PCF_STS
_OK
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ED_MAN
CLK_OUT
RXCLK
Reserved
SAMPLE_
PARAM
RESTART
_ON_FRE
Q
Reserved
VAR_DAT
A
Reserved
Reserved
TDR_PEA
K
TDR_STA
RT
Reserved
Reserved
Reserved
VAR_DAT
A
Reserved
Reserved
TDR_PEA
K
TDR_STA
RT
Reserved
WRITE_L
Q_THR
Reserved
LQ_PARA
M_SEL
RESTART RESTART
_ON_DBL _ON_DAG
W
C
Reserved
VAR_DAT
A
Reserved
Reserved
TDR_PEA
K
TDR_STA
RT
Reserved
Reserved
ED_ERR_
MET
SOFT_RE
SET
PCF_DA_
SEL
Reserved
ED_DATA
_MET
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SD_Time
Reserved
TEST REGISTERS - PAGE 1
Reserved
Reserved
ED_PWR_
STATE
PHYTER_
COMP
RESTART
_ON_VAR
LQ_PARA
M_SEL
RESTART
_ON_C1
Reserved
VAR_DAT
A
Reserved
Reserved
TDR_PEA
K
TDR_STA
RT
TDR_WID
TH
Reserved
Reserved
Reserved
LQ_PARA
M_SEL
FC_HI_WA
RN
Reserved
VAR_DAT
A
Reserved
Reserved
TDR_PEA
K
TDR_STA
RT
TDR_WID
TH
Reserved
Reserved
Reserved
Reserved
Reserved
PCF_INT_
CTL
Reserved
ED_ERR_
COUNT
Reserved
Reserved
LP_DIS
Reserved
LQ_THR_
SEL
Bit 6
Reserved
Reserved
Reserved
PCF_INT_
CTL
Reserved
ED_ERR_
COUNT
Reserved
MII_CLOC
K_EN
LINK_10
FORCE_
CNFG[1]
LED_
TDR_PEA
K_TIME
TDR_STO
P
Reserved
FREQ_OF
FSET
Reserved
VAR_DAT
A
Reserved
Reserved
LQ_THR_
DATA
Reserved
LQ_THR_
DATA
FREQ_LO
_WARN
Reserved
VAR_DAT
A
Reserved
TDRTDRTHR_TIME THR_TIME
TDR_PEA
K_TIME
TDR_STO
P
TDR_MIN_
MODE
FREQ_OF
FSET
CABLE_LE CABLE_LE
N
N
FC_LO_W FREQ_HI_
ARN
WARN
Reserved
VAR_DAT
A
Reserved
TDR_THR
_MET
TDR_PEA
K
TDR_STA
RT
TDR_WID
TH
SEL_FC
Reserved
Bit 7
BP_STRE
TCH
LINK DIAGNOSTICS REGISTERS - PAGE 2
Reserved
Reserved
Reserved
Reserved
Reserved
ED_BURS
T_DIS
BC_WRIT
E
TX_CHAN RX_CHAN SEND_TD
NEL
NEL
R
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ED_AUTO ED_AUTO
_UP
_DOWN
Reserved
LQM_ENA RESTART
BLE
_ON_FC
Reserved
VAR_DAT
A
VAR_RDY
Reserved
Reserved
TDR_STA
RT
TDR_ENA
BLE
SAMPLE_
FREQ
Reserved
Reserved
Reserved
Reserved
PCF_STS
_ERR
Reserved
ED_EN
Reserved
BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR BIST_ERR
OR_COU OR_COU OR_COU OR_COU OR_COU OR_COUN OR_COUN OR_COUN
NT
NT
NT
NT
NT
T
T
T
Reserved
MDIX_EN
Bit 5
Reserved
CDPATTE
N_10
POLARITY
ADDR
PHY
Bit 4
Reserved
MDIO_PUL
L_EN
AUTOPOL_
DIS
ADDR
PHY
Bit 3
Reserved
CABLE_LE
N
Reserved
Reserved
Reserved
PCF_BUF
Reserved
CABLE_LE
N
Reserved
Reserved
Reserved
PCF_BUF
HEARTBEA
T_DIS
ADDR
PHY
Bit 1
JABBER_
DIS
ADDR
PHY
Bit 0
CABLE_LE
N
Reserved
Reserved
Reserved
PCF_BUF
Reserved
ED_DATA_
COUNT
Reserved
CABLE_LE
N
Reserved
Reserved
Reserved
PCF_BUF
Reserved
ED_DATA_
COUNT
CLK_OUT_
DIS
CABLE_L
EN
Reserved
Reserved
Reserved
PCF_EN
Reserved
ED_DATA
_COUNT
Reserved
PATT_GAP CDPATTSE CDPATTS
_10M
L
EL
10BT_SCA
LE_MSB
ADDR
PHY
Bit 2
TDRTHR_TIME
TDRTHR_TIME
Reserved
LQ_THR_D
ATA
DBLW_HI_
WARN
Reserved
VAR_DATA
VAR_TIME
R
TDRTHR_TIME
VAR_TIME
R
TDRTHR_TIME
Reserved
LQ_THR_D
ATA
DBLW_LO_
WARN
Reserved
Reserved
LQ_THR_D
ATA
DAGC_HI_
WARN
Reserved
Reserved
LQ_THR_D
ATA
DAGC_LO_
WARN
Reserved
VAR_HI_W
ARN
LQ_THR_D
ATA
C1_HI_WA
RN
Reserved
VAR_DATA VAR_DATA VAR_DATA VAR_DATA
LOAD_VAR LOAD_VAR VAR_FREE
_HI
_LO
ZE
TDRTHR_TIME
Reserved
LQ_THR_
DATA
C1_LO_W
ARN
Reserved
VAR_DAT
A
VAR_ENA
BLE
TDRTHR_TIM
E
TDR_PEAK TDR_PEAK TDR_PEAK TDR_PEAK TDR_PEAK TDR_PEA
_TIME
_TIME
_TIME
_TIME
_TIME
K_TIME
TDR_STOP TDR_STOP TDR_STOP TDR_STOP TDR_STOP TDR_STO
P
RX_THRES RX_THRES RX_THRES RX_THRES RX_THRES RX_THRE
HOLD
HOLD
HOLD
HOLD
HOLD
SHOLD
FREQ_OFF FREQ_OFF FREQ_OFF FREQ_OFF FREQ_OFF FREQ_OF
SET
SET
SET
SET
SET
FSET
CABLE_LE
N
Reserved
Reserved
Reserved
PCF_BC_DI
S
Reserved
ED_ERR_C ED_ERR_C ED_DATA_
OUNT
OUNT
COUNT
Reserved
BIST_CON
T
FORCE_PO
L COR
CNFG[0]
LED_
DP83630
www.national.com
1Fh
14h
15h
16h
17h
18h
PTP Event Data
Register
Timestamp
PTP Trigger
Configuration
Register
PTP Event
Configuration
Register
PTP Transmit
Configuration
Register 0
PTP Transmit
Configuration
Register 1
PHY Status Frame
Configuration
Register 0
19h
1Fh
PTP Event Data
Register Status
PTP Receive
Configuration
Register 0
1Eh
PTP Event Status
Register
Reserved
TRIG_PUL
SE
PTP_EVN
T_TS
E7_RISE
Reserved
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
PTP_RXC
FG0
PSF_CFG
0
DOMAIN_
EN
Reserved
PTP_TXCF BYTE0_M
G1
ASK
PTP_TXCF SYNC_1S
G0
TEP
PTP_EVN
T
PTP_TRIG
PTP_EDA
TA
PTP_EDA
TA
PTP_ESTS
PTP_RXT
S
Reserved
Reserved
PTP_Rate
_Lo
TRIG_IF_
LATE
PTP_EVN
T_TS
E6_RISE
Reserved
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
Reserved
Reserved
BYTE0_M
ASK
Reserved
Reserved
Reserved
TRIG_DIS
TRIG_EN
RD_CKSU
M
PTP_Rate
_Hi
PTP_Rate
_Lo
TRIG4_AC
TIVE
EVENT_R
DY
RD_CKSU
M
PTP_Rate
_Hi
PTP_Rate
_Lo
TRIG3_ER
ROR
Reserved
BYTE0_M
ASK
RESERVE
D_1
RD_CKSU
M
PTP_Rate
_Hi
PTP_Rate
_Lo
TRIG3_AC
TIVE
Reserved
PTP_EVN
T_TS
E5_DET
PTP_EVN
T_TS
E4_RISE
PTP_EVN
T_TS
E4_DET
PTP_EVN
T_TS
E3_RISE
TRIG_GPI
O
TRIG_GPI
O
TRIG_GPI
O
MIN_PRE
BYTE0_M
ASK
CHK_1ST
EP
MIN_PRE
BYTE0_M
ASK
TX_IPV6_
EN
Reserved
Reserved
PSF_ENDI
AN
RX_IPV6_
EN
PSF_IPV4
BYTE0_DA BYTE0_DA
TA
TA
IP1588_EN TX_L2_EN
RX_SLAV IP1588_EN IP1588_EN IP1588_EN RX_L2_EN
E
MIN_PRE
BYTE0_M
ASK
CRC_1ST
EP
Reserved
TRIG_TOG
GLE
PTP_EVN
T_TS
E3_DET
EVNTS_MI EVNTS_MI EVNTS_MI EVNT_TS_ EVNT_TS_
SSED
SSED
SSED
LEN
LEN
PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T PTP_RX_T
S
S
S
S
S
PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T PTP_TX_T
S
S
S
S
S
WR_CKSU WR_CKSU WR_CKSU WR_CKSU WR_CKSU
M
M
M
M
M
RD_CKSU
M
PTP_Rate
_Hi
PTP_Rate
_Lo
TRIG4_ER
ROR
TRIG_DO
NE
EVNT_GP EVNT_GPI EVNT_GPI EVNT_GPI
IO
O
O
O
TRIG_GPI
O
Reserved
Bit 6
TRIG_REA TRIG_LOA
D
D
Reserved
Bit 7
PTP 1588 CONFIGURATION REGISTERS - PAGE 5
PTP_EVN
T_TS
E5_RISE
Reserved
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
MAC_SRC MAC_SRC
_ADD
_ADD
BYTE0_M
ASK
Reserved
Reserved
TRIG_NO
TIFY
PTP_EVN
T_TS
E6_DET
Reserved
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
USER_IP_ USER_IP_
SEL
EN
Reserved
BYTE0_M
ASK
DR_INSE
RT
EVNT_RIS EVNT_FA
E
LL
TRIG_PE
R
PTP_EVN
T_TS
E7_DET
Reserved
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
RD_CKSU
M
Reserved
PTP_Rate
_Lo
1Dh
Reserved
PTP_Rate
_Lo
PTP Receive
TimeStamp
Register
PTP_TXTS
PTP_TMP
_RATE
PTP_Rate
_Lo
RD_CKSU RD_CKSU RD_CKSU RD_CKSU RD_CKSU
M
M
M
M
M
PTP_RAT
E_DIR
PTP_Rate
_Lo
1Ch
RXTS_RD
Y
PTP Transmit
TimeStamp
Register
PTP_WRC
KSUM
PTP_RDC
KSUM
PTP_RAT
EH
PTP_Rate
_Lo
Bit 8
TIME_DAT TIME_DAT TIME_DAT TIME_DAT TIME_DAT
A
A
A
A
A
1Bh
TXTS_RD
Y
TIME_DA
TA
PTP Page 4 Write
Checksum
Reserved
TIME_DA
TA
1Ah
Reserved
Reserved
PTP Page 4 Read
Checksum
Reserved
TIME_DA
TA
Bit 9
PTP 1588 BASE REGISTERS - PAGE 4
TRIG_SEL TRIG_SEL TRIG_SEL
Reserved
Bit 10
RESERVED REGISTERS - PAGE 3
19h
Reserved
TIME_DA
TA
Reserved
Reserved
Bit 11
PTP Rate High
Register
PTP_STS
TIME_DA
TA
Reserved
Reserved
Bit 12
PTP_RAT
EL
16h
PTP Status
Register
PTP_TDR
Reserved
Reserved
Bit 13
18h
15h
PTP Time Data
Register
PTP_CTL
Reserved
Bit 14
PTP Rate Low
Register
14h
PTP Control
Register
Reserved
Bit 15
PTP_TSTS TRIG7_ER TRIG7_AC TRIG6_ER TRIG6_AC TRIG5_ER TRIG5_AC
ROR
TIVE
ROR
TIVE
ROR
TIVE
14h-1Fh
RESERVED
Tag
PTP Trigger Status 17h
Register
Addr
Register Name
RX_IPV4_E
N
PSF_PCF_
RD
BYTE0_DA
TA
TX_IPV4_E
N
Reserved
Reserved
PTP_EVNT
_TS
E2_RISE
EVNT_RF
PTP_RX_T
S
PTP_TX_T
S
WR_CKSU
M
RD_CKSU
M
PTP_Rate_
Hi
PTP_Rate_
Lo
TRIG2_ER
ROR
Reserved
TIME_DAT
A
PTP_RD_C
LK
Reserved
Bit 5
RX_PTP_V
ER
PSF_ERR_
EN
BYTE0_DA
TA
TX_PTP_V
ER
Reserved
Reserved
PTP_EVNT
_TS
E2_DET
EVNT_NU
M
PTP_RX_T
S
PTP_TX_T
S
WR_CKSU
M
RD_CKSU
M
PTP_Rate_
Hi
PTP_Rate_
Lo
TRIG2_AC
TIVE
Reserved
TIME_DAT
A
PTP_LOAD
_CLK
Reserved
Bit 4
Reserved
Bit 1
Reserved
Bit 0
PTP_EVNT
_TS
E1_DET
EVNT_NU
M
PTP_RX_T
S
PTP_TX_T
S
WR_CKSU
M
RD_CKSU
M
PTP_Rate_
Hi
PTP_Rate_
Lo
TRIG1_AC
TIVE
RXTS_IE
TIME_DAT
A
PTP_RX_
TS
PTP_TX_
TS
WR_CKS
UM
RD_CKS
UM
PTP_Rate
_Hi
PTP_Rate
_Lo
TRIG0_A
CTIVE
EVENT_I
E
TIME_DA
TA
PTP_EVNT
_TS
E0_RISE
PTP_EVN
T_TS
E0_DET
MULT_EVN EVENT_D
T
ET
PTP_RX_T
S
PTP_TX_T
S
WR_CKSU
M
RD_CKSU
M
PTP_Rate_
Hi
PTP_Rate_
Lo
TRIG0_ER
ROR
TRIG_IE
TIME_DAT
A
PTP_ENAB PTP_DISAB PTP_RES
LE
LE
ET
Reserved
Bit 2
RX_PTP_V
ER
PSF_TXTS
_EN
BYTE0_DA
TA
TX_PTP_V
ER
EVNT_SEL
BYTE0_DA
TA
TX_PTP_V
ER
EVNT_SEL
BYTE0_D
ATA
TX_TS_E
N
EVNT_W
R
RX_PTP_V
ER
RX_PTP_V
ER
RX_TS_E
N
PSF_RXTS PSF_TRIG_ PSF_EVN
_EN
EN
T_EN
BYTE0_DA
TA
TX_PTP_V
ER
EVNT_SEL
TRIG_CSEL TRIG_CSE TRIG_CSEL TRIG_WR
L
PTP_EVNT
_TS
E1_RISE
EVNT_NUM
PTP_RX_T
S
PTP_TX_T
S
WR_CKSU
M
RD_CKSU
M
PTP_Rate_
Hi
PTP_Rate_
Lo
TRIG1_ER
ROR
TXTS_IE
TIME_DAT
A
PTP_STEP
_CLK
Reserved
Bit 3
DP83630
43
www.national.com
44
Bit 15
1Fh
PTP Receive Hash
Register
PTP_RXH
ASH
PTP_GPIO
MON
1Eh
Bit 14
BYTE0_M
ASK
Bit 13
BYTE0_M
ASK
Bit 12
BYTE0_M
ASK
Bit 11
BYTE0_M
ASK
Bit 10
BYTE0_M
ASK
PTPRESE
RVED
PTP_CLK
OUT SEL
Reserved
PTP_TR_
DURL
TS_SEC_
EN
TS_MIN_I
FG
PTPRESE
RVED
PTP_CLK
OUT
SPEEDSE
L
Reserved
PTP_TR_
DURL
TS_SEC_
LEN
TS_MIN_I
FG
PTPRESE
RVED
Reserved
Reserved
PTP_TR_
DURL
TS_SEC_
LEN
TS_MIN_I
FG
VERSION
PTP
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PTP_ETY
PE
Reserved
Reserved
Reserved
PTP_ETY
PE
CLK_SRC
Reserved
Reserved
IP_CHKS
UM
Reserved
Reserved
Reserved
PTP_ETY
PE
Reserved
Reserved
Reserved
IP_CHKS
UM
RX_HASH
_EN
Reserved
Reserved
PTP_ETY
PE
Reserved
Reserved
Reserved
IP_CHKS
UM
PTP_RX_
HASH
PTP_GPI
O_IN
Reserved
PTP_ETY
PE
Reserved
Reserved
Reserved
IP_CHKS
UM
IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY
TE3
TE3
TE3
TE3
TE3
IP_CHKS
UM
RXTS_NS
_OFF
TS_APPE
ND
IP_ADDR_
DATA
Bit 8
RXTS_NS
_OFF
TS_INSER
T
IP_ADDR_
DATA
BYTE0_M
ASK
Bit 7
Bit 6
RXTS_NS
_OFF
PTP_DOM
AIN
IP_ADDR_
DATA
Reserved
RXTS_NS
_OFF
IP_SA_BY
TE3
IP_SA_BY
TE1
VERSION
PTP
Reserved
IP_SA_BY
TE3
IP_SA_BY
TE1
VERSION
PTP
Reserved
IP_SA_BY
TE2
IP_SA_BY
TE0
IP_SA_BY
TE2
IP_SA_BY
TE0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TX_SFD_
GPIO
CLK_SRC
_PER
Reserved
TX_SFD_
GPIO
Reserved
Reserved
PTP_DOMA
IN
IP_ADDR_
DATA
Bit 2
PTP_DOM
AIN
IP_ADDR_
DATA
BYTE0_DA
TA
Bit 1
PTP_DOMA
IN
IP_ADDR_
DATA
BYTE0_DA
TA
PTP_TR_D
URH
PTP_TR_D
URL
PTP_TR_D
URH
PTP_TR_D
URL
PTP_TR_D
URH
PTP_TR_D
URL
PTP_TR_D
URH
PTP_TR_D
URL
PTP_OFF
SET
PTP_OFF
SET
PTP_RX_
HASH
PTP_RX_
HASH
PTP_RX_
HASH
PTP_RX_
HASH
PTP_RX_
HASH
Bit 0
PTP_TR_
DURH
PTP_TR_
DURL
RXTS_SE
C_OFF
PTP_DO
MAIN
IP_ADDR
_DATA
BYTE0_D
ATA
PTP_OFFS
ET
PTP_ETYP
E
CLK_SRC_
PER
Reserved
TX_SFD_G
PIO
IP_CHKSU
M
PTP_OFFS
ET
PTP_ETYP
E
CLK_SRC_
PER
Reserved
TX_SFD_G
PIO
IP_CHKSU
M
IP_CHKSU
M
IP_CHKSU
M
PTP_OFFS
ET
PTP_ETYP
E
CLK_SRC_
PER
PTP_INT_G
PIO
PTP_OFFS
ET
PTP_ETYP
E
CLK_SRC_
PER
PTP_INT_
GPIO
PTP_RX_H
ASH
PTP_RX_H
ASH
PTP_RX_H
ASH
PTP_RX_H
ASH
RX_SFD_
GPIO
IP_CHKS
UM
PTP_OFFS
ET
PTP_ETYP
E
CLK_SRC_
PER
PTP_RX_H
ASH
PTP_RX_
HASH
PTP_GPI
O_IN
PTP_OFF
SET
PTP_ETY
PE
CLK_SRC
_PER
PTP_INT_G PTP_INT_
PIO
GPIO
RX_SFD_G RX_SFD_G RX_SFD_G
PIO
PIO
PIO
IP_CHKSU
M
IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BY
E2
E2
E2
E2
E2
TE2
IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BYT IP_SA_BY
E0
E0
E0
E0
E0
TE0
MESSAG
ETYPE
PTP_CLKDI PTP_CLKD PTP_CLKDI PTP_CLKD PTP_CLKDI PTP_CLK
V
IV
V
IV
V
DIV
PTP_TR_D
URH
PTP_TR_D
URL
RXTS_SEC RXTS_SEC RXTS_SEC RXTS_SEC RXTS_SEC
_OFF
_OFF
_OFF
_OFF
_OFF
PTP_DOM
AIN
IP_ADDR_
DATA
Bit 3
BYTE0_DA
TA
PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO PTP_GPIO_ PTP_GPIO PTP_GPIO_ PTP_GPIO PTP_GPIO_
_IN
_IN
_IN
_IN
_IN
IN
_IN
IN
_IN
IN
Reserved
PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP PTP_ETYP
E
E
E
E
E
Reserved
Reserved
Reserved
IP_ADDR_
DATA
Bit 4
BYTE0_DA
TA
TRANSPO TRANSPO TRANSPOR TRANSPO MESSAGET MESSAGE MESSAGET
RTSPECIF RTSPECIF TSPECIFIC RTSPECIFI
YPE
TYPE
YPE
IC
IC
C
PTP_CLK
DIV
PTP_CLK
DIV
PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D
URH
URH
URH
URH
IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU IP_CHKSU
M
M
M
M
M
IP_SA_BY
TE3
IP_SA_BY
TE1
VERSION
PTP
Reserved
Bit 5
BYTE0_DA
TA
PTP_DOM PTP_DOMA
AIN
IN
IP_ADDR_
DATA
BYTE0_DA BYTE0_DA
TA
TA
PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D PTP_TR_D
URL
URL
URL
URL
URL
RXTS_NS
_OFF
Bit 9
BYTE0_M
ASK
PTP 1588 CONFIGURATION REGISTERS - PAGE 6
Reserved
PTP_TR_
DURL
RXTS_NS
_OFF
ACC_UDP ACC_CRC
IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY IP_SA_BY
TE1
TE1
TE1
TE1
TE1
PTPRESE
RVED
PTP_CLK
OUT EN
Reserved
PTP_TR_
DURL
IPV4_UDP
_MOD
TS_MIN_I
FG
IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_ IP_ADDR_
DATA
DATA
DATA
DATA
DATA
DATA
BYTE0_M
ASK
PTP_CLKS CLK_SRC
RC
PTP GPIO Monitor
Register
1Bh
PTP Clock Source
Register
PTP_INTC
TL
PTP_OFF
1Ah
PTP Interrupt
Control Register
PTP_SFD
CFG
1Dh
19h
PTP SFD
Congiguration
Register
PSF_CFG
4
PTP Offset
Register
18h
Status Frame
Configuration
Register 4
PSF_CFG
3
PTP_ETR
17h
Status Frame
Configuration
Register 3
PSF_CFG
2
PTP Ethernet Type 1Ch
Register
16h
Status Frame
Configuration
Register 2
PSF_CFG
1
15h
PTP_TRDL
PHY Status Frame
Configuration
Register 1
1Eh
PTP Temporary
Rate Duration Low
Register
PTP_RXC
FG4
PTP_COC
1Dh
PTP Receive
Configuration
Register 4
PTP_RXC
FG3
14h
1Ch
PTP Receive
Configuration
Register 3
PTP_RXC
FG2
PTP Clock Output
Control Register
1Bh
PTP Receive
Configuration
Register 2
PTP_RXC
FG1
Tag
PTP_TRD
H
1Ah
PTP Receive
Configuration
Register 1
PTP Temporary
1Fh
Rate Duration High
Register
Addr
Register Name
DP83630
DP83630
14.1 REGISTER DEFINITION
In the register definitions under the ‘Default’ heading, the following definitions hold true:
— RW = Read Write access
— SC = Register sets on event occurrence and Self-Clears when event ends
— RW/SC = ReadWrite access/Self Clearing bit
— RO = Read Only access
— COR = Clear On Read
— RO/COR = Read Only, Clear On Read
— RO/P = Read Only, Permanently set to a default value
— LL = Latched Low and held until read, based upon the occurrence of the corresponding event
— LH = Latched High and held until read, based upon the occurrence of the corresponding event
45
www.national.com
DP83630
14.1.1 Basic Mode Control Register (BMCR)
TABLE 14. Basic Mode Control Register (BMCR), address 0x00
Bit
Bit Name
Default
15
RESET
0, RW/SC
14
LOOPBACK
0, RW
13
SPEED SELECTION
Strap, RW
Speed Select:
When auto-negotiation is disabled writing to this bit allows the port speed to be
selected.
1 = 100 Mb/s.
0 = 10 Mb/s.
12
AUTO-NEGOTIATION
ENABLE
Strap, RW
Auto-Negotiation Enable:
Strap controls initial value at reset.
If FX is enabled (FX_EN = 1), then this bit will be reset to 0.
1 = Auto-Negotiation Enabled - bits 8 and 13 of this register are ignored when this bit
is set.
0 = Auto-Negotiation Disabled - bits 8 and 13 determine the port speed and duplex
mode.
11
POWER DOWN
0, RW
Power Down:
1 = Power down.
0 = Normal operation.
Setting this bit powers down the PHY. Only the register block is enabled during a
power down condition. This bit is ORd with the input from the PWRDOWN_INT pin.
When the active low PWRDOWN_INT pin is asserted, this bit will be set.
10
ISOLATE
0, RW
Isolate:
1 = Isolates the Port from the MII with the exception of the serial management.
0 = Normal operation.
9
RESTART
AUTO-NEGOTIATION
0, RW/SC
Restart Auto-Negotiation:
1 = Restart Auto-Negotiation. Re-initiates the Auto-Negotiation process. If AutoNegotiation is disabled (bit 12 = 0), this bit is ignored. This bit is self-clearing and will
return a value of 1 until Auto-Negotiation is initiated, whereupon it will self-clear.
Operation of the Auto-Negotiation process is not affected by the management entity
clearing this bit.
0 = Normal operation.
8
DUPLEX MODE
Strap, RW
Duplex Mode:
When auto-negotiation is disabled writing to this bit allows the port Duplex capability
to be selected.
1 = Full Duplex operation.
0 = Half Duplex operation.
7
COLLISION TEST
0, RW
Collision Test:
1 = Collision test enabled.
0 = Normal operation.
When set, this bit will cause the COL signal to be asserted in response to the assertion
of TX_EN within 512-bit times. The COL signal will be de-asserted within 4-bit times
in response to the de-assertion of TX_EN.
www.national.com
Description
Reset:
1 = Initiate software Reset / Reset in Process.
0 = Normal operation.
This bit, which is self-clearing, returns a value of one until the reset process is
complete. The configuration is re-strapped.
Loopback:
1 = Loopback enabled.
0 = Normal operation.
The loopback function enables MII transmit data to be routed to the MII receive data
path.
Setting this bit may cause the descrambler to lose synchronization and produce a 500
µs “dead time” before any valid data will appear at the MII receive outputs.
46
Bit Name
Default
DP83630
Bit
Description
6
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
5
UNIDIRECTIONAL
ENABLE
0, RW
Unidirectional Enable:
1 = Allow 100 Mb transmit activity independent of link status.
0 = Require link up for 100 Mb/s transmit activity.
This bit has no effect in 10 Mb/s mode..
4:0
RESERVED
0 0000, RO
RESERVED: Write ignored, read as 0.
47
www.national.com
DP83630
14.1.2 Basic Mode Status Register (BMSR)
TABLE 15. Basic Mode Status Register (BMSR), address 0x01
Bit
Bit Name
Default
Description
15
100BASE-T4
0, RO/P
100BASE-T4 Capable:
0 = Device not able to perform 100BASE-T4 mode.
14
100BASE-TX
FULL DUPLEX
1, RO/P
100BASE-TX Full Duplex Capable:
1 = Device able to perform 100BASE-TX in full duplex mode.
13
100BASE-TX
HALF DUPLEX
1, RO/P
100BASE-TX Half Duplex Capable:
1 = Device able to perform 100BASE-TX in half duplex mode.
12
10BASE-T
FULL DUPLEX
1, RO/P
10BASE-T Full Duplex Capable:
1 = Device able to perform 10BASE-T in full duplex mode.
11
10BASE-T
HALF DUPLEX
1, RO/P
10BASE-T Half Duplex Capable:
1 = Device able to perform 10BASE-T in half duplex mode.
10:8
RESERVED
000, RO
RESERVED: Write as 0, read as 0.
7
UNIDIRECTIONAL
ABILITY
1, RO/P
Unidirectional Ability:
1 = Device able to transmit in 100 Mb/s mode independent of link status.
6
MF PREAMBLE
SUPPRESSION
1, RO/P
Preamble Suppression Capable:
1 = Device able to perform management transaction with preamble suppressed, 32-bits
of preamble needed only once after reset, invalid opcode or invalid turnaround.
0 = Normal management operation.
5
AUTO-NEGOTIATION
COMPLETE
0, RO
4
REMOTE FAULT
0, RO/LH
3
AUTO-NEGOTIATION
ABILITY
1, RO/P
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation.
0 = Device is not able to perform Auto-Negotiation.
2
LINK STATUS
0, RO/LL
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
The criteria for link validity is implementation specific. The occurrence of a link failure
condition will causes the Link Status bit to clear. Once cleared, this bit may only be set
by establishing a good link condition and a read via the management interface.
1
JABBER DETECT
0, RO/LH
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
1 = Jabber condition detected.
0 = No Jabber.
This bit is implemented with a latching function, such that the occurrence of a jabber
condition causes it to set until it is cleared by a read to this register by the management
interface or by a reset.
0
EXTENDED
CAPABILITY
1, RO/P
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete.
0 = Auto-Negotiation process not complete.
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far
End Fault Indication or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected.
Extended Capability:
1 = Extended register capabilities.
0 = Basic register set capabilities only.
The PHY Identifier Registers #1 and #2 together form a unique identifier for the DP83630. The Identifier consists of a concatenation
of the Organizationally Unique Identifier (OUI), the vendor's model number and the model revision number. A PHY may return a
value of zero in each of the 32 bits of the PHY Identifier if desired. The PHY Identifier is intended to support network management.
National's IEEE assigned OUI is 080017h.
www.national.com
48
DP83630
14.1.3 PHY Identifier Register #1 (PHYIDR1)
TABLE 16. PHY Identifier Register #1 (PHYIDR1), address 0x02
Bit
Bit Name
15:0
OUI_MSB
Default
Description
0010 0000 0000 0000, OUI Most Significant Bits: Bits 3 to 18 of the OUI (080017h) are stored in bits 15
RO/P
to 0 of this register. The most significant two bits of the OUI are ignored (the IEEE
standard refers to these as bits 1 and 2).
14.1.4 PHY Identifier Register #2 (PHYIDR2)
TABLE 17. PHY Identifier Register #2 (PHYIDR2), address 0x03
Bit
Bit Name
Default
15:10
OUI_LSB
0101 11, RO/P
OUI Least Significant Bits:
Bits 19 to 24 of the OUI (080017h) are mapped from bits 15 to 10 of this register
respectively.
Description
9:4
VNDR_MDL
00 1110, RO/P
Vendor Model Number:
The six bits of vendor model number are mapped from bits 9 to 4 (most significant bit
to bit 9).
3:0
MDL_REV
0001, RO/P
Model Revision Number:
Four bits of the vendor model revision number are mapped from bits 3 to 0 (most
significant bit to bit 3). This field will be incremented for all major device changes.
49
www.national.com
DP83630
14.1.5 Auto-Negotiation Advertisement Register (ANAR)
This register contains the advertised abilities of this device as they will be transmitted to its link partner during Auto-Negotiation.
Any writes to this register prior to completion of Auto-Negotiation (as indicated in the Basic Mode Status Register (address 01h)
Auto-Negotiation Complete bit, BMSR[5]) should be followed by a renegotiation. This will ensure that the new values are properly
used in the Auto-Negotiation.
TABLE 18. Auto-Negotiation Advertisement Register (ANAR), address 0x04
Bit
Bit Name
Default
15
NP
0, RW
14
RESERVED
0, RO/P
13
RF
0, RW
Remote Fault:
1 = Advertises that this device has detected a Remote Fault.
0 = No Remote Fault detected.
12
RESERVED
0, RW
RESERVED for Future IEEE use: Write as 0, Read as 0
11
ASM_DIR
0, RW
Asymmetric PAUSE Support for Full Duplex Links:
The ASM_DIR bit indicates that asymmetric PAUSE is supported.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables
28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control
sublayer and the pause function as specified in clause 31 and annex 31B of 802.3u.
0 = No MAC based full duplex flow control.
10
PAUSE
0, RW
PAUSE Support for Full Duplex Links:
The PAUSE bit indicates that the device is capable of providing the symmetric PAUSE
functions as defined in Annex 31B.
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables
28B-2 and 28B-3, respectively. Pause resolution status is reported in PHYCR[13:12].
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control
sublayer and the pause function as specified in clause 31 and annex 31B of 802.3u.
0 = No MAC based full duplex flow control.
9
T4
0, RO/P
8
TX_FD
Strap, RW
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the local device.
0 = 100BASE-TX Full Duplex not supported.
7
TX
Strap, RW
100BASE-TX Support:
1 = 100BASE-TX is supported by the local device.
0 = 100BASE-TX not supported.
6
10_FD
Strap, RW
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the local device.
0 = 10BASE-T Full Duplex not supported.
5
10
Strap, RW
10BASE-T Support:
1 = 10BASE-T is supported by the local device.
0 = 10BASE-T not supported.
4:0
SELECTOR
0 0001, RW
www.national.com
Description
Next Page Indication:
0 = Next Page Transfer not desired.
1 = Next Page Transfer desired.
RESERVED by IEEE: Writes ignored, Read as 0.
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the local device.
0 = 100BASE-T4 not supported.
Protocol Selection Bits:
These bits contain the binary encoded protocol selector supported by this port.
<00001> indicates that this device supports IEEE 802.3u.
50
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The content changes after
the successful auto-negotiation if Next-pages are supported.
TABLE 19. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 0x05
Bit
Bit Name
Default
15
NP
0, RO
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer.
1 = Link Partner desires Next Page Transfer.
Description
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control this bit based on the
incoming FLP bursts.
13
RF
0, RO
Remote Fault:
1 = Remote Fault indicated by Link Partner.
0 = No Remote Fault indicated by Link Partner.
12
RESERVED
0, RO
RESERVED for Future IEEE use: Write as 0, read as 0.
11
ASM_DIR
0, RO
ASYMMETRIC PAUSE:
1 = Asymmetric pause is supported by the Link Partner.
0 = Asymmetric pause is not supported by the Link Partner.
10
PAUSE
0, RO
PAUSE:
1 = Pause function is supported by the Link Partner.
0 = Pause function is not supported by the Link Partner.
9
T4
0, RO
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the Link Partner.
0 = 100BASE-T4 not supported by the Link Partner.
8
TX_FD
0, RO
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the Link Partner.
0 = 100BASE-TX Full Duplex not supported by the Link Partner.
7
TX
0, RO
100BASE-TX Support:
1 = 100BASE-TX is supported by the Link Partner.
0 = 100BASE-TX not supported by the Link Partner.
6
10_FD
0, RO
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the Link Partner.
0 = 10BASE-T Full Duplex not supported by the Link Partner.
5
10
0, RO
10BASE-T Support:
1 = 10BASE-T is supported by the Link Partner.
0 = 10BASE-T not supported by the Link Partner.
4:0
SELECTOR
0 0000, RO
Protocol Selection Bits:
Link Partner's binary encoded protocol selector.
51
www.national.com
DP83630
14.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
DP83630
14.1.7 Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page)
TABLE 20. Auto-Negotiation Link Partner Ability Register (ANLPAR) (Next Page), address 0x05
Bit
Bit Name
Default
Description
15
NP
0, RO
Next Page Indication:
1 = Link Partner desires Next Page Transfer.
0 = Link Partner does not desire Next Page Transfer.
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word.
0 = Not acknowledged.
The Auto-Negotiation state machine will automatically control this bit based on the
incoming FLP bursts. Software should not attempt to write to this bit.
13
MP
0, RO
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RO
Acknowledge 2:
1 = Link Partner does have the ability to comply to next page message.
0 = Link Partner does not have the ability to comply to next page message.
11
TOGGLE
0, RO
Toggle:
1 = Previous value of the transmitted Link Code word equalled 0.
0 = Previous value of the transmitted Link Code word equalled 1.
10:0
CODE
000 0000 0000, RO Code:
This field represents the code field of the next page transmission. If the MP bit is
set (bit 13 of this register), then the code shall be interpreted as a Message Page,
as defined in IEEE 802.3u Annex 28C of Clause 28. Otherwise, the code shall be
interpreted as an Unformatted Page, and the interpretation is application specific.
14.1.8 Auto-Negotiate Expansion Register (ANER)
This register contains additional Local Device and Link Partner status information.
TABLE 21. Auto-Negotiate Expansion Register (ANER), address 0x06
Bit
Bit Name
15:5
RESERVED
4
PDF
0, RO
Parallel Detection Fault:
1 = A fault has been detected via the Parallel Detection function.
0 = A fault has not been detected.
3
LP_NP_ABLE
0, RO
Link Partner Next Page Able:
1 = Link Partner does support Next Page.
0 = Link Partner does not support Next Page.
2
NP_ABLE
1, RO/P
1
PAGE_RX
0, RO/COR
0
LP_AN_ABLE
0, RO
www.national.com
Default
Description
0000 0000 000, RO RESERVED: Writes ignored, Read as 0.
Next Page Able:
1 = Indicates local device is able to send additional Next Pages.
Link Code Word Page Received:
1 = Link Code Word has been received, cleared on a read.
0 = Link Code Word has not been received.
Link Partner Auto-Negotiation Able:
1 = Indicates that the Link Partner supports Auto-Negotiation.
0 = Indicates that the Link Partner does not support Auto-Negotiation.
52
DP83630
14.1.9 Auto-Negotiation Next Page Transmit Register (ANNPTR)
This register contains the next page information sent by this device to its Link Partner during Auto-Negotiation.
TABLE 22. Auto-Negotiation Next Page Transmit Register (ANNPTR), address 0x07
Bit
Bit Name
Default
Description
15
NP
0, RW
Next Page Indication:
0 = No other Next Page Transfer desired.
1 = Another Next Page desired.
14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
13
MP
1, RW
Message Page:
1 = Message Page.
0 = Unformatted Page.
12
ACK2
0, RW
Acknowledge2:
1 = Will comply with message.
0 = Cannot comply with message.
Acknowledge2 is used by the next page function to indicate that Local Device
has the ability to comply with the message received.
11
TOG_TX
0, RO
Toggle:
1 = Value of toggle bit in previously transmitted Link Code Word was 0.
0 = Value of toggle bit in previously transmitted Link Code Word was 1.
Toggle is used by the Arbitration function within Auto-Negotiation to ensure
synchronization with the Link Partner during Next Page exchange. This bit shall
always take the opposite value of the Toggle bit in the previously exchanged
Link Code Word.
10:0
CODE
000 0000 0001, RW
Code:
This field represents the code field of the next page transmission. If the MP bit
is set (bit 13 of this register), then the code shall be interpreted as a "Message
Page”, as defined in Annex 28C of IEEE 802.3u. Otherwise, the code shall be
interpreted as an "Unformatted Page”, and the interpretation is application
specific.
The default value of the CODE represents a Null Page as defined in Annex 28C
of IEEE 802.3u.
53
www.national.com
DP83630
14.1.10 PHY Status Register (PHYSTS)
This register provides a single location within the register set for quick access to commonly accessed information.
TABLE 23. PHY Status Register (PHYSTS), address 0x10
Bit
Bit Name
Default
15
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
14
MDIX MODE
0, RO
MDIX mode as reported by the Auto-Negotiation logic:
This bit will be affected by the settings of the MDIX_EN and FORCE_MDIX
bits in the PHYCR register. When MDIX is enabled, but not forced, this bit will
update dynamically as the Auto-MDIX algorithm swaps between MDI and
MDIX configurations.
1 = MDI pairs swapped
(Receive on TPTD pair, Transmit on TPRD pair)
0 = MDI pairs normal
(Receive on TPRD pair, Transmit on TPTD pair)
13
RECEIVE ERROR
LATCH
0, RO/LH
Receive Error Latch:
This bit will be cleared upon a read of the RECR register.
1 = Receive error event has occurred since last read of RXERCNT (address
15h, Page 0).
0 = No receive error event has occurred.
12
POLARITY STATUS
0, RO
Polarity Status:
This bit is a duplication of bit 4 in the 10BTSCR register. This bit will be cleared
upon a read of the 10BTSCR register, but not upon a read of the PHYSTS
register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
11
FALSE CARRIER
SENSE LATCH
0, RO/LH
False Carrier Sense Latch:
This bit will be cleared upon a read of the FCSR register.
1 = False Carrier event has occurred since last read of FCSCR (address 14h).
0 = No False Carrier event has occurred.
10
SIGNAL DETECT
0, RO/LL
100Base-TX qualified Signal Detect from PMA:
This is the SD that goes into the link monitor. It is the AND of raw SD and
descrambler lock, when address 16h, bit 8 (page 0) is set. When bit 8 of
address 16h is cleared, it will be equivalent to the raw SD from the PMD.
9
DESCRAMBLER LOCK
0, RO/LL
100Base-TX Descrambler Lock from PMD.
8
PAGE RECEIVED
0, RO
Link Code Word Page Received:
This is a duplicate of the Page Received bit in the ANER register, but this bit
will not be cleared upon a read of the PHYSTS register.
1 = A new Link Code Word Page has been received. Cleared on read of the
ANER (address 06h, bit 1).
0 = Link Code Word Page has not been received.
7
MII INTERRUPT
0, RO
MII Interrupt Pending:
1 = Indicates that an internal interrupt is pending. Interrupt source can be
determined by reading the MISR Register (12h). Reading the MISR will clear
the Interrupt.
0 = No interrupt pending.
6
REMOTE FAULT
0, RO
Remote Fault:
1 = Remote Fault condition detected (cleared on read of BMSR (address 01h)
register or by reset). Fault criteria: notification from Link Partner of Remote
Fault via Auto-Negotiation.
0 = No remote fault condition detected.
www.national.com
Description
54
Bit Name
Default
Description
5
JABBER DETECT
0, RO
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
This bit is a duplicate of the Jabber Detect bit in the BMSR register, except
that it is not cleared upon a read of the PHYSTS register.
1 = Jabber condition detected.
0 = No Jabber.
4
AUTO-NEG COMPLETE
0, RO
Auto-Negotiation Complete:
1 = Auto-Negotiation complete.
0 = Auto-Negotiation not complete.
3
LOOPBACK STATUS
0, RO
Loopback:
1 = Loopback enabled.
0 = Normal operation.
2
DUPLEX STATUS
0, RO
Duplex:
This bit indicates duplex status and is determined from Auto-Negotiation or
Forced Modes.
1 = Full duplex mode.
0 = Half duplex mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and
there is a valid link or if Auto-Negotiation is disabled and there is a valid link.
1
SPEED STATUS
0, RO
Speed10:
This bit indicates the status of the speed and is determined from AutoNegotiation or Forced Modes.
1 = 10 Mb/s mode.
0 = 100 Mb/s mode.
Note: This bit is only valid if Auto-Negotiation is enabled and complete and
there is a valid link or if Auto-Negotiation is disabled and there is a valid link.
0
LINK STATUS
0, RO
Link Status:
This bit is a duplicate of the Link Status bit in the BMSR register, except that
it will not be cleared upon a read of the PHYSTS register.
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
55
www.national.com
DP83630
Bit
DP83630
14.1.11 MII Interrupt Control Register (MICR)
This register implements the MII Interrupt PHY Specific Control register. Sources for interrupt generation include: Link Quality
Monitor, Energy Detect State Change, Link State Change, Speed Status Change, Duplex Status Change, Auto-Negotiation Complete or any of the counters becoming half-full. The individual interrupt events must be enabled by setting bits in the MII Interrupt
Status and Event Control Register (MISR).
TABLE 24. MII Interrupt Control Register (MICR), address 0x11
Bit
Bit Name
15:4
RESERVED
3
PTP_INT_SEL
0, RW
PTP Interrupt Select:
Maps PTP Interrupt to the MISR register in place of the Duplex Interrupt. The
Duplex Interrupt will be combined with the Speed Interrupt.
1 = Map PTP Interrupt to MISR[11] , Speed/Duplex Interrupt to MISR[12]
0 = Map Duplex Interrupt to MISR[11], Speed Interrupt to MISR[12]
2
TINT
0, RW
Test Interrupt:
Forces the PHY to generate an interrupt to facilitate interrupt testing. Interrupts
will continue to be generated as long as this bit remains set.
1 = Generate an interrupt.
0 = Do not generate interrupt.
1
INTEN
0, RW
Interrupt Enable:
Enable interrupt dependent on the event enables in the MISR register.
1 = Enable event based interrupts.
0 = Disable event based interrupts.
0
INT_OE
0, RW
Interrupt Output Enable:
Enable interrupt events to signal via the PWRDOWN/INTN pin by configuring the
PWRDOWN/INTN pin as an output.
1 = PWRDOWN/INTN is an Interrupt Output.
0 = PWRDOWN/INTN is a Power Down Input.
www.national.com
Default
Description
0000 0000 0000, RO RESERVED: Writes ignored, read as 0.
56
This register contains event status and enables for the interrupt function. If an event has occurred since the last read of this register,
the corresponding status bit will be set. If the corresponding enable bit in the register is set, an interrupt will be generated if the
event occurs. The MICR register controls must also be set to allow interrupts. The status indications in this register will be set even
if the interrupt is not enabled.
TABLE 25. MII Interrupt Status and Event Control Register (MISR), address 0x12
Bit
Bit Name
Default
15
LQ_INT
0, RO/COR
Link Quality Interrupt:
1 = Link Quality interrupt is pending and is cleared by the current read.
0 = No Link Quality interrupt pending.
Description
14
ED_INT
0, RO/COR
Energy Detect Interrupt:
1 = Energy detect interrupt is pending and is cleared by the current read.
0 = No energy detect interrupt pending.
13
LINK_INT
0, RO/COR
Change of Link Status Interrupt:
1 = Change of link status interrupt is pending and is cleared by the current read.
0 = No change of link status interrupt pending.
12
SPD_INT
or
SPD_DUP_INT
0, RO/COR
Change of Speed Status Interrupt:
Change of speed status interrupt. This function is selected if MICR[3] is set to 0.
1 = Speed status change interrupt is pending and is cleared by the current read.
0 = No speed status change interrupt pending.
Change of Speed/Duplex Interrupt:
Change of speed or duplex status interrupt. This function is selected if MICR[3]
is set to 1.
1 = Speed/duplex status change interrupt is pending and is cleared by the current
read.
0 = No speed/duplex status change interrupt pending.
11
DUP_INT
or
PTP_INT
0, RO/COR
Change of Duplex Status Interrupt:
Change of duplex status interrupt. This function is selected if MICR[3] is set to 0.
1 = Duplex status change interrupt is pending and is cleared by the current read.
0 = No duplex status change interrupt pending.
PTP Interrupt:
PTP interrupt. This function is selected if MICR[3] is set to 1. PTP interrupt status
should be read from the PTP_STS register. This interrupt will not be rearmed until
the PTP_STS register indicates no further PTP status is available.
1 = PTP interrupt is pending and is cleared by the current read.
0 = No PTP interrupt pending.
10
ANC_INT
0, RO/COR
Auto-Negotiation Complete Interrupt:
1 = Auto-negotiation complete interrupt is pending and is cleared by the current
read.
0 = No Auto-negotiation complete interrupt pending.
9
FHF_INT
or
CTR_INT
0, RO/COR
False Carrier Counter Half-Full Interrupt:
False carrier counter half-full interrupt. This function is selected if the PHYCR2
[8:7] are both 0.
1 = False carrier counter half-full interrupt is pending and is cleared by the current
read.
0 = No false carrier counter half-full interrupt pending.
CTR Interrupt:
False carrier or Receive Error counter half-full interrupt. This function is selected
if either of PHYCR2[8:7] are set.
1 = False carrier or receive error counter half-full interrupt is pending and is
cleared by the current read.
0 = No false carrier or receive error counter half-full interrupt pending.
57
www.national.com
DP83630
14.1.12 MII Interrupt Status and Event Control Register (MISR)
DP83630
Bit
Bit Name
Default
Description
8
RHF_INT
or
PCF_INT
0, RO/COR
Receive Error Counter half-full interrupt:
Receive error counter half-full interrupt. This function is selected if the PHYCR2
[8:7] are both 0.
1 = Receive error counter half-full interrupt is pending and is cleared by the current
read.
0 = No receive error carrier counter half-full interrupt pending.
PCF Interrupt:
PHY Control Frame interrupt. This function is selected if either of PHYCR2[8:7]
are set.
1 = PHY Control Frame interrupt is pending and is cleared by the current read.
0 = No PHY Control Frame interrupt pending.
7
LQ_INT_EN
0, RW
Enable Interrupt on Link Quality Monitor event.
6
ED_INT_EN
0, RW
Enable Interrupt on energy detect event.
5
LINK_INT_EN
0, RW
Enable Interrupt on change of link status.
4
SPD_INT_EN
0, RW
Enable Interrupt on change of speed status.
3
DUP_INT_EN
or
PTP_INT_EN
0, RW
Duplex Interrupt:
Enable Interrupt on change of duplex status. This function is selected if MICR[3]
is set to 0.
PTP Interrupt:
PTP interrupt. This function is selected if MICR[3] is set to 1.
2
ANC_INT_EN
0, RW
Enable Interrupt on auto-negotiation complete event.
1
FHF_INT_EN
or
CTR_INT_EN
0, RW
FHF Interrupt:
Enable Interrupt on False Carrier Counter Register halffull event. This function is
selected if the PHYCR2[8:7] are both 0.
CTR Interrupt:
Enable interrupt on either Receive Error Counter Register half-full event or False
Carrier Counter Register half-full event. This function is selected if either of
PCFCR[7:6] are set.
0
RHF_INT_EN
or
PCF_INT_EN
0, RW
RHF Interrupt:
Enable Interrupt on Receive Error Counter Register halffull event. This function
is selected if the PHYCR2[8:7] are both 0.
PCF Interrupt:
Enable Interrupt on a PHY Control Frame event. This function is selected if either
of PCFCR[7:6] are set.
www.national.com
58
DP83630
14.1.13 Page Select Register (PAGESEL)
This register is used to enable access to the Link Diagnostics Registers.
TABLE 26. Page Select Register (PAGESEL), address 0x13
Bit
Bit Name
Default
15:3
RESERVED
0000 0000 0000 0,
RO
2:0
PAGE_SEL
000, RW
Description
RESERVED: Writes ignored, read as 0
Page_Sel Bits:
Selects between paged registers for address 14h to 1Fh.
0 = Extended Registers Page 0
1 = RESERVED
2 = Link Diagnostics Registers Page 2
3 = RESERVED
4 = PTP 1588 Base Registers Page 4
5 = PTP 1588 Config Registers Page 5
6 = PTP 1588 Config Registers Page 6
14.2 EXTENDED REGISTERS - PAGE 0
14.2.1 False Carrier Sense Counter Register (FCSCR)
This counter provides information required to implement the “False Carriers” attribute within the MAU managed object class of
Clause 30 of the IEEE 802.3u specification.
TABLE 27. False Carrier Sense Counter Register (FCSCR), address 0x14
Bit
Bit Name
15:8
RESERVED
7:0
FCSCNT[7:0]
Default
0000 0000, RO
Description
RESERVED: Writes ignored, read as 0
0000 0000, RO/COR False Carrier Event Counter:
This 8-bit counter increments on every false carrier event. This counter sticks
when it reaches its maximum count (FFh).
14.2.2 Receiver Error Counter Register (RECR)
This counter provides information required to implement the “Symbol Error During Carrier” attribute within the PHY managed object
class of Clause 30 of the IEEE 802.3u specification.
TABLE 28. Receiver Error Counter Register (RECR), address 0x15
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
7:0
RXERCNT[7:0]
Description
RESERVED: Writes ignored, read as 0.
0000 0000, RO/COR RX_ER Counter:
When a valid carrier is present and there is at least one occurrence of an invalid
data symbol, this 8-bit counter increments for each receive error detected. This
event can increment only once per valid carrier event. If a collision is present, the
attribute will not increment. The counter sticks when it reaches its maximum count.
59
www.national.com
DP83630
14.2.3 100 Mb/s PCS Configuration and Status Register (PCSR)
This register contains control and status information for the 100BASE Physical Coding Sublayer.
TABLE 29. 100 Mb/s PCS Configuration and Status Register (PCSR), address 0x16
Bit
Bit Name
Default
Description
15
AUTO_CROSSOV
ER
0, RW
14:12
RESERVED
000, RW
11
FREE_CLK
0, RW
Receive Clock:
1 = RX_CLK is free-running.
0 = RX_CLK phase adjusted based on alignment.
10
TQ_EN
0, RW
100 Mb/s True Quiet Mode Enable:
1 = Transmit True Quiet Mode.
0 = Normal Transmit Mode.
9
SD FORCE PMA
0, RW
Signal Detect Force PMA:
1 = Forces Signal Detection in PMA.
0 = Normal SD operation.
8
SD_OPTION
1, RW
Signal Detect Option:
1 = Default operation. Link will be asserted following detection of valid signal level
and Descrambler Lock. Link will be maintained as long as signal level is valid. A
loss of Descrambler Lock will not cause Link Status to drop.
0 = Modified signal detect algorithm. Link will be asserted following detection of
valid signal level and Descrambler Lock. Link will be maintained as long as signal
level is valid and Descrambler remains locked.
7
DESC_TIME
0, RW
Descrambler Timeout:
Increase the descrambler timeout. When set, this allows the device to receive
larger packets (>9k bytes) without loss of synchronization.
1 = 2 ms.
0 = 722 µs (per ANSI X3.263: 1995 (TP-PMD) 7.2.3.3e).
6
FX_EN
Strap, RW
FX Fiber Mode Enable:
This bit is set when the FX_EN strap option is selected for the respective port.
Write PHYCR2[9], SOFT_RESET, after enabling or disabling Fiber Mode via
register access to ensure correct configuration.
1 = Enables FX operation.
0 = Disables FX operation.
5
FORCE_100_OK
0, RW
Force 100 Mb/s Good Link:
OR’ed with MAC_FORCE_LINK_100 signal.
1 = Forces 100 Mb/s Good Link.
0 = Normal 100 Mb/s operation.
4
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
3
FEFI_EN
Strap, RW
2
NRZI_BYPASS
0, RW
Auto-Crossover in Forced Mode:
1 = Auto-Crossover in Forced Mode Enabled
Allows the device to toggle between MDIX and MDI channels when forced to 10M
or 100M mode. This function is mutually exclusive with the Auto-Negotiation
Enable bit, BMCR[12], and with the Auto-MDIX Enable bit, PHYCR[15]. These
bits should not be set when enabling Auto-crossover.
0 = Normal operation
www.national.com
RESERVED: Must be 0.
Far End Fault Indication Mode Enable:
This bit is set when the FX_EN strap option is selected for the respective port.
1 = FEFI Mode Enabled.
0 = FEFI Mode Disabled.
NRZI Bypass Enable:
1 = NRZI Bypass Enabled.
0 = NRZI Bypass Disabled.
60
Bit Name
Default
Description
1
SCRAM
BYPASS
Strap, RW
Scrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected. In the FX mode, the
scrambler is bypassed.
1 = Scrambler Bypass Enabled.
0 = Scrambler Bypass Disabled.
0
DESCRAM
BYPASS
Strap, RW
Descrambler Bypass Enable:
This bit is set when the FX_EN strap option is selected. In the FX mode, the
descrambler is bypassed.
1 = Descrambler Bypass Enabled.
0 = Descrambler Bypass Disabled.
61
www.national.com
DP83630
Bit
DP83630
14.2.4 RMII and Bypass Register (RBR)
This register configures the RMII/MII Interface Mode of operation. This register controls selecting MII, RMII, or Single Clock MII
mode for Receive or Transmit. In addition, several additional bits are included to allow datapath selection for Transmit and Receive
in multiport applications.
TABLE 30. RMII and Bypass Register (RBR), address 0x17
Bit
Bit Name
Default
Description
15
RESERVED
0, RW
14
RMII_MASTER
Strap, RW
RMII Master Mode:
Setting this bit allows the core to use a 25 MHz input reference clock and generate
its own 50 MHz RMII reference clock. The generated RMII reference clock will
also be used by the attached MAC.
1 = RMII Master Mode (25 MHz input reference)
0 = RMII Slave Mode (50 MHz input reference)
Note: Due to clock muxing and divider operation, this bit should normally only be
reconfigured via the strap option.
13
DIS_TX_OPT
0, RW
Disable RMII TX Latency Optimization:
Normally the RMII Transmitter will minimize the transmit latency by realigning the
transmit clock with the reference clock phase at the start of a packet transmission.
Setting this bit will disable phase realignment and ensure that IDLE bits will
always be sent in multiples of the symbol size. This will result in a larger
uncertainty in RMII transmit latency.
12:9
RESERVED
0000, RW
8
PMD_LOOP
0, RW
PMD Loopback:
0 = Normal Operation.
1 = Remote (PMD) Loopback.
Setting this bit will cause the device to Loopback data received from the Physical
Layer. The loopback is done prior to the MII or RMII interface. Data received at
the internal MII or RMII interface will be applied to the transmitter. This mode
should only be used if RMII mode or Single Clock MII mode is enabled.
7
SCMII_RX
0, RW
Single Clock RX MII Mode:
0 = Standard MII mode.
1 = Single Clock RX MII Mode.
Setting this bit will cause the device to generate receive data (RX_DV, RX_ER,
RXD[3:0]) synchronous to the X1 Reference clock. RX_CLK is not used in this
mode. This mode uses the RMII elasticity buffer to tolerate variations in clock
frequencies. This bit cannot be set if RMII_MODE is set to a 1.
6
SCMII_TX
0, RW
Single Clock TX MII Mode:
0 = Standard MII mode.
1 = Single Clock TX MII Mode.
Setting this bit will cause the device to sample transmit data (TX_EN, TXD[3:0])
synchronous to the X1 Reference clock. TX_CLK is not used in this mode. This
bit cannot be set if RMII_MODE is set to a 1.
5
RMII_MODE
Strap, RW
4
RMII_REV1_0
0, RW
Reduced MII Revision 1.0:
This bit modifies how CRS_DV is generated.
0 = (RMII revision 1.2) CRS_DV will toggle at the end of a packet to indicate
deassertion of CRS.
1 = (RMII revision 1.0) CRS_DV will remain asserted until final data is transferred.
CRS_DV will not toggle at the end of a packet.
3
RX_OVF_STS
0, RO
RX FIFO Over Flow Status:
0 = Normal.
1 = Overflow detected.
www.national.com
RESERVED: Must be 0.
RESERVED: Must be 0.
Reduced MII Mode:
0 = Standard MII Mode.
1 = Reduced MII Mode.
62
Bit Name
Default
2
RX_UNF_STS
0, RO
1:0
ELAST_BUF[1:0]
01, RW
DP83630
Bit
Description
RX FIFO Under Flow Status:
0 = Normal.
1 = Underflow detected.
Receive Elasticity Buffer:
This field controls the Receive Elasticity Buffer which allows for frequency
variation tolerance between the 50 MHz RMII clock and the recovered data. See
Section 10.2 REDUCED MII INTERFACEfor more information on Elasticity Buffer
settings in RMII mode. See Section Section 10.3 SINGLE CLOCK MII MODEfor
more information on Elasticity Buffer settings in SCMII mode.
14.2.5 LED Direct Control Register (LEDCR)
This register provides the ability to directly control any or all LED outputs. It does not provide read access to LEDs. In addition, it
provides control for the Activity source and blinking LED frequency.
TABLE 31. LED Direct Control Register (LEDCR), address 0x18
Bit
Bit Name
Default
15:12
RESERVED
0000, RO
Description
11
DIS_SPDLED
0, RW
1 = Disable LED_SPEED output
0 = Enable LED_SPEED output
10
DIS_LNKLED
0, RW
1 = Disable LED_LINK output
0 = Enable LED_LINK output
9
DIS_ACTLED
0, RW
1 = Disable LED_ACT output
0 = Enable LED_ACT output
8
LEDACT_RX
0, RW
1 = Activity is only indicated for Receive traffic
0 = Activity is indicated for Transmit or Receive traffic
7:6
BLINK_FREQ
00, RW
LED Blink Frequency:
These bits control the blink frequency of the LED_LINK output when blinking on
activity is enabled.
0 = 6 Hz
1 = 12 Hz
2 = 24 Hz
3 = 48 Hz
5
DRV_SPDLED
0, RW
1 = Drive value of SPDLED bit onto LED_SPEED output
0 = Normal operation
4
DRV_LNKLED
0, RW
1 = Drive value of LNKLED bit onto LED_LINK output
0 = Normal operation
3
DRV_ACTLED
0, RW
1 = Drive value of ACTLED bit onto LED_ACT output
0 = Normal operation
2
SPDLED
0, RW
Value to force on LED_SPEED output
1
LNKLED
0, RW
Value to force on LED_LINK output
0
ACTLED
0, RW
Value to force on LED_ACT output
RESERVED: Writes ignored, read as 0.
63
www.national.com
DP83630
14.2.6 PHY Control Register (PHYCR)
This register provides control for PHY functions such as MDIX, BIST, LED configuration, and PHY address. It also provides Pause
Negotiation status.
TABLE 32. PHY Control Register (PHYCR), address 0x19
Bit
Bit Name
Default
15
MDIX_EN
1, RW
Auto-MDIX Enable:
1 = Enable Auto-neg Auto-MDIX capability.
0 = Disable Auto-neg Auto-MDIX capability.
14
FORCE_MDIX
0, RW
Force MDIX:
1 = Force MDI pairs to cross.
(Receive on TD pair, Transmit on RD pair)
0 = Normal operation.
13
PAUSE_RX
0, RO
Pause Receive Negotiated:
Indicates that pause receive should be enabled in the MAC. Based on ANAR
[11:10] and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3,
“Pause Resolution”, only if the Auto-Negotiated Highest Common Denominator
is a full duplex technology.
12
PAUSE_TX
0, RO
Pause Transmit Negotiated:
Indicates that pause transmit should be enabled in the MAC. Based on ANAR
[11:10] and ANLPAR[11:10] settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3,
Pause Resolution, only if the Auto-Negotiated Highest Common Denominator is
a full duplex technology.
11
BIST_FE
0, RW/SC
10
PSR_15
0, RW
9
BIST_STATUS
0, LL/RO
8
BIST_START
0, RW
BIST Start:
Writes:
1 = BIST start. Writing 1 to this bit enables transmission of BIST packets and
enables the receive BIST engine to start looking for packet traffic.
0 = BIST stop. Stop the BIST. Writing 0 to this bit also clears the BIST_STATUS
bit.
Reads:
1 = BIST active. This bit reads 1 after the transmit BIST engine has been enabled
and the receive BIST engine has detected packet traffic.
0 = BIST inactive. This bit will read 0 if the BIST is disabled or if the BIST is enabled
but no receive traffic has been detected.
7
BP_STRETCH
0, RW
Bypass LED Stretching:
This will bypass the LED stretching and the LEDs will reflect the internal value.
1 = Bypass LED stretching.
0 = Normal operation.
www.national.com
Description
BIST Force Error:
1 = Force BIST Error.
0 = Normal operation.
This bit forces a single error, and is self clearing.
BIST Sequence select:
1 = PSR15 selected.
0 = PSR9 selected.
BIST Test Status:
1 = BIST pass.
0 = BIST fail. Latched, cleared when a BIST failure occurs or BIST is stopped.
For a count number of BIST errors, see the BIST Error Count in the CDCTRL1
register.
64
Bit Name
Default
6
5
LED_CNFG[1]
LED_CNFG[0]
0, RW
Strap, RW
DP83630
Bit
Description
LED Configuration
LED_CNFG[1]
LED_CNFG[0]
Mode Description
Don't care
1
Mode 1
0
0
Mode 2
1
0
Mode 3
In Mode 1, LEDs are configured as follows:
LED_LINK = ON for Good Link, OFF for No Link
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Activity, OFF for No Activity
In Mode 2, LEDs are configured as follows:
LED_LINK = ON for Good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Collision, OFF for No Collision
In Mode 3, LEDs are configured as follows:
LED_LINK = ON for Good Link, BLINK for Activity
LED_SPEED = ON in 100 Mb/s, OFF in 10 Mb/s
LED_ACT = ON for Full Duplex, OFF for Half Duplex
4:0
PHYADDR[4:0]
Strap, RW
PHY Address: PHY address for port.
Note: The local PHY address cannot be changed via a broadcast write - writing
to PHY address 0x1F register 0x19 will not change the PHYADDR bits.
65
www.national.com
DP83630
14.2.7 10Base-T Status/Control Register (10BTSCR)
This register is used for control and status for 10BASE-T device operation.
TABLE 33. 10Base-T Status/Control Register (10BTSCR), address 0x1A
Bit
Bit Name
Default
Description
15
RESERVED
0, RO
14:12
RESERVED
000, RW
RESERVED: Must be zero.
11:9
SQUELCH
100, RW
Squelch Configuration:
Used to set the Squelch 'ON' threshold for the receiver.
Default Squelch 'ON' is 330mV peak.
8
LOOPBACK_10_DIS
0, RW
10Base-T Loopback Disable:
This bit is OR’ed with bit 14 (Loopback) in the BMCR.
1 = 10BT Loopback is disabled
0 = 10BT Loopback is enabled
7
LP_DIS
0, RW
Normal Link Pulse Disable:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
1 = Transmission of NLPs is disabled.
0 = Transmission of NLPs is enabled.
6
FORCE_LINK_10
0, RW
Force 10 Mb Good Link:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
1 = Forced Good 10 Mb Link.
0 = Normal Link Status.
5
FORCE_POL COR
0, RW
Force 10 Mb Polarity Correction:
1 = Force inverted polarity
0 = Normal polarity
4
POLARITY
0, RO/LH
3
AUTOPOL_DIS
0, RW
Auto Polarity Detection & Correction Disable:
1 = Polarity Correction disabled
0 = Polarity Correction enabled
2
10BT_SCALE - MSB
1, RW
10BT Scale Configuration Most Significant Bit
Used in conjunction with bit 10 of SD_CNFG register to set the silence ’OFF’
threshold for the receiver.
1
HEARTBEAT_DIS
0, RW
Heartbeat Disable:
This bit only has influence in half-duplex 10 Mb mode.
1 = Heartbeat function disabled.
0 = Heartbeat function enabled.
When the device is operating at 100 Mb or configured for full duplex
operation, this bit will be ignored - the heartbeat function is disabled.
0
JABBER_DIS
0, RW
Jabber Disable:
This bit is only applicable in 10BASE-T.
1 = Jabber function disabled.
0 = Jabber function enabled.
www.national.com
RESERVED: Writes ignored, read as 0.
10 Mb Polarity Status:
This bit is a duplication of bit 12 in the PHYSTS register. Both bits will be
cleared upon a read of either register.
1 = Inverted Polarity detected.
0 = Correct Polarity detected.
66
This register controls test modes for the 10BASE-T Common Driver. In addition it contains extended control and status for the
packet BIST function.
TABLE 34. CD Test and BIST Extensions Register (CDCTRL1), address 0x1B
Bit
Bit Name
Default
Description
15:8
BIST_ERROR_COUNT
0000 0000, RO
BIST ERROR Counter:
Counts number of errored data nibbles during Packet BIST. This value
will reset when Packet BIST is restarted. The counter sticks when it
reaches its maximum count of FFh.
7
RESERVED
0, RW
RESERVED: Must be 0.
6
MII_CLOCK_EN
0, RW
Enables MII Clocks TX_CLK and RX_CLK independent of MAC
interface mode selected; for example, normally TX_CLK and RX_CLK
are disabled in RMII Slave mode.
1 = Enable TX_CLK and RX_CLK
0 = Default operation
5
BIST_CONT
0, RW
Packet BIST Continuous Mode:
Allows continuous pseudorandom data transmission without any break
in transmission. This can be used for transmit VOD testing. This is used
in conjunction with the BIST controls in the PHYCR Register (19h). For
10 Mb operation, jabber function must be disabled, bit 0 of the
10BTSCR (1Ah), JABBER_DIS = 1.
4
CDPATTEN_10
0, RW
CD Pattern Enable for 10 Mb:
1 = Enabled.
0 = Disabled.
3
MDIO_PULL_EN
0, RW
Enable Internal MDIO Pullup:
1 = Internal MDIO pullup enabled
0 = Internal MDIO pullup disabled
This bit is only reset on hard reset. This bit should not be set in systems
that share the management interfaces among several ASICs.
2
PATT_GAP_10M
0, RW
Defines gap between data or NLP test sequences:
1 = 15 µs.
0 = 10 µs.
1:0
CDPATTSEL[1:0]
00, RW
CD Pattern Select[1:0]:
If CDPATTEN_10 = 1:
00 = Data, EOP0 sequence.
01 = Data, EOP1 sequence.
10 = NLPs.
11 = Constant Manchester 1s (10 MHz sine wave) for harmonic
distortion testing.
67
www.national.com
DP83630
14.2.8 CD Test and BIST Extensions Register (CDCTRL1)
DP83630
14.2.9 PHY Control Register 2 (PHYCR2)
This register provides additional general control.
TABLE 35. PHY Control Register 2 (PHYCR2), address 0x1C
Bit
Bit Name
Default
15:14
RESERVED
00, RO
RESERVED: Writes ignored, read as 0.
13
SYNC_ENET EN
0, RW
Synchronous Ethernet Enable:
When this bit is 1 and the device is in 100 Mb/s mode, and the MAC
interface is either MII or RMII Master, enables fully synchronous
communication relative to the recovered receive clock. The transmitter
is synchronized to the receiver.
When this bit is 0 or the device settings do not match the above
conditions, the transmitter is synchronous to the local reference clock.
12
CLK_OUT RXCLK
0, RW
Enable RX_CLK on CLK_OUT:
When this bit is 1 and the device is in 100 Mb/s mode, the 25 MHz
recovered receive clock (RX_CLK) is driven on CLK_OUT in addition
to RX_CLK. When this bit is 0 or the device is in 10 Mb/s mode,
CLK_OUT reflects the Reference clock.
11
BC_WRITE
0, RW
Broadcast Write Enable:
1 = Enables the Serial Management Interface to accept register writes
to PHY Address of 0x1F independent of the local PHY Address value.
0 = Normal operation
10
PHYTER_COMP
0, RW
Phyter Compatibility Mode:
1 = Enables Phyter (DP83848) Compatible pinout. Reorders the RX MII
pins and Autonegotiation straps to match the DP83848. Also enables
the CLK_OUT output.
0 = Normal operation
9
SOFT_RESET
0, RW/SC
8:2
RESERVED
0 0000 00, RO
1
CLK_OUT_DIS
Strap, RW
0
RESERVED
0, RW
www.national.com
Description
Soft Reset:
Resets the entire device minus the registers - all configuration is
preserved.
1 = Reset, self-clearing.
RESERVED: Writes ignored, read as 0.
Disable CLK_OUT Output:
Disables the CLK_OUT output pin.
RESERVED: Must be zero.
68
DP83630
14.2.10 Energy Detect Control (EDCR)
This register provides control and status for the Energy Detect function.
TABLE 36. Energy Detect Control (EDCR), address 0x1D
Bit
Bit Name
Default
Description
15
ED_EN
0, RW
Energy Detect Enable:
Allow Energy Detect Mode.
14
ED_AUTO_UP
1, RW
Energy Detect Automatic Power Up:
Automatically begin power up sequence when Energy Detect Data
Threshold value (EDCR[3:0]) is reached. Alternatively, the device could
be powered up manually using the ED_MAN bit (ECDR[12]).
13
ED_AUTO_DOWN
1, RW
Energy Detect Automatic Power Down:
Automatically begin power down sequence when no energy is detected.
Alternatively, the device could be powered down using the ED_MAN bit
(EDCR[12]).
12
ED_MAN
0, RW/SC
Energy Detect Manual Power Up/Down:
Begin power up/down sequence when this bit is asserted. When set,
the Energy Detect algorithm will initiate a change of Energy Detect state
regardless of threshold (error or data) and timer values. In managed
applications, this bit can be set after clearing the Energy Detect interrupt
to control the timing of changing the power state.
11
ED_BURST_DIS
0, RW
Energy Detect Burst Disable:
Disable bursting of energy detect data pulses. By default, Energy Detect
(ED) transmits a burst of 4 ED data pulses each time the CD is powered
up. When bursting is disabled, only a single ED data pulse will be sent
each time the CD is powered up.
10
ED_PWR_STATE
0, RO
Energy Detect Power State:
Indicates current Energy Detect Power state. When set, Energy Detect
is in the powered up state. When cleared, Energy Detect is in the
powered down state. This bit is invalid when Energy Detect is not
enabled.
9
ED_ERR_MET
0, RO/COR
Energy Detect Error Threshold Met:
No action is automatically taken upon receipt of error events. This bit is
informational only and would be cleared on a read.
8
ED_DATA_MET
0, RO/COR
Energy Detect Data Threshold Met:
The number of data events that occurred met or surpassed the Energy
Detect Data Threshold. This bit is cleared on a read.
7:4
ED_ERR_COUNT
0001, RW
Energy Detect Error Threshold:
Threshold to determine the number of energy detect error events that
should cause the device to take action. Intended to allow averaging of
noise that may be on the line. Counter will reset after approximately 2
seconds without any energy detect data events.
3:0
ED_DATA_COUNT
0001, RW
Energy Detect Data Threshold:
Threshold to determine the number of energy detect events that should
cause the device to take actions. Intended to allow averaging of noise
that may be on the line. Counter will reset after approximately 2 seconds
without any energy detect data events.
69
www.national.com
DP83630
14.2.11 PHY Control Frames Configuration Register (PCFCR)
This register provides configuration for the PHY Control Frame mechanism for register access.
TABLE 37. PHY Control Frames Configuration Register (PCFCR), address 0x1F
Bit
Bit Name
Default
Description
15
PCF_STS_ERR
0, RO/COR
PHY Control Frame Error Detected:
Indicates an error was detected in a PCF Frame since the last read of
this register. This bit will be cleared on read.
14
PCF_STS_OK
0, RO/COR
PHY Control Frame OK:
Indicates a PCF Frame has completed without error since the last read
of this register. This bit will be cleared on read.
13:9
RESERVED
00 000, RO
Reserved: Writes ignored, read as 0
8
PCF_DA_SEL
0, RW
Select MAC Destination Address for PHY Control Frames:
0 : Use MAC Address [08 00 17 0B 6B 0F]
1 : Use MAC Address [08 00 17 00 00 00]
The device will also recognize packets with the above address with the
Multicast bit set (i.e. 09 00 17 ...).
7:6
PCF_INT_CTL
00, RW
PHY Control Frame Interrupt Control:
Setting either of these bits enables control and status of the PCF
Interrupt through the MISR Register (taking the place of the RHF
Interrupt).
00 = PCF Interrupts Disabled
x1 = Interrupt on PCF Frame OK
1x = Interrupt on PCF Frame Error
5
PCF_BC_DIS
0, RW
PHY Control Frame Broadcast Disable:
By default, the device will accept broadcast PHY Control Frames which
have a PHY Address field of 0x1F. If this bit is set to a 1, the PHY Control
Frame must have a PHY Address field that exactly matches the device
PHY Address.
4:1
PCF_BUF
0 000, RW
PHY Control Frame Buffer Size:
Determines the buffer size for transmit to allow PHY Control Frame
detection. All packets will be delayed as they pass through this buffer.
If set to 0, packets will not be delayed and PHY Control frames will be
truncated after the Destination Address field.
0
PCF_EN
Strap, RW
PHY Control Frame Enable:
Enables Register writes using PHY Control Frames.
www.national.com
70
DP83630
14.3 TEST REGISTERS - PAGE 1
Page 1 Test Registers are accessible by setting bits [2:0] = 001 of PAGESEL (13h).
14.3.1 Signal Detect Configuration (SD_CNFG), Page 1
This register contains Signal Detect configuration control as well as some test controls to speed up Auto-neg testing.
TABLE 38. Signal Detect Configuration (SD_CNFG), address 0x1E
Bit
Bit Name
Default
15
RESERVED
1, RW
RESERVED: Write as 1, read as 1.
Description
14:12
RESERVED
000, RW
RESERVED: Write as 0, read as 0.
11
RESERVED
0, RO
10:9
RESERVED
00, RW
RESERVED: Write as 0, read as 0.
8
SD_TIME
0, RW
Signal Detect Time
Setting this bit to a 1 enables a fast detection of loss of Signal Detect.
This will result in a fast loss of Link indication. Approximate times to
detect signal detect deassertion are:
1 = 1 µs
0 = 250 µs
7:0
RESERVED
0000 0000, RW
RESERVED: Write ignored, read as 0.
RESERVED: Write as 0, read as 0.
71
www.national.com
DP83630
14.4 LINK DIAGNOSTICS REGISTERS - PAGE 2
Page 2 Link Diagnostics Registers are accessible by setting bits [2:0] = 010 of PAGESEL (13h).
14.4.1 100 Mb Length Detect Register (LEN100_DET), Page 2
This register contains linked cable length estimation in 100 Mb operation. The cable length is an estimation of the effective cable
length based on the characteristics of the recovered signal. The cable length is valid only during 100 Mb operation with a valid Link
status indication.
TABLE 39. 100 Mb Length Detect Register (LEN100_DET), address 0x14
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
RESERVED: Writes ignored, read as 0.
Description
7:0
CABLE_LEN
1111 1111, RO
Cable Length Estimate:
Indicates an estimate of effective cable length in meters. A value of
FFh indicates cable length cannot be determined.
14.4.2 100 Mb Frequency Offset Indication Register (FREQ100), Page 2
This register returns an indication of clock frequency offset relative to the link partner. Two values can be read, the long term
Frequency Offset, or a short term Frequency Control value. The Frequency Control value includes short term phase correction.
The variance between the Frequency Control value and the Frequency Offset can be used as an indication of the amount of jitter
in the system.
TABLE 40. 100 Mb Frequency Offset Indication Register (FREQ100), address 0x15
Bit
Bit Name
Default
Description
15
SAMPLE_FREQ
0, WO
Sample Frequency Offset:
If SEL_FC is set to a 0, then setting this bit to a 1 will poll the DSP for
the long-term Frequency Offset value. The value will be available in
the FREQ_OFFSET bits of this register.
If SEL_FC is set to a 1, then setting this bit to a 1 will poll the DSP for
the current Frequency Control value. The value will be available in the
FREQ_OFFSET bits of this register.
This register bit will always read back as 0.
14:9
RESERVED
000 000, RO
8
SEL_FC
0, RW
Select Frequency Control:
Setting this bit to a 1 will select the current Frequency Control value
instead of the Frequency Offset. This value contains Frequency Offset
plus the short term phase correction and can be used to indicate
amount of jitter in the system. The value will be available in the
FREQ_OFFSET bits of this register.
7:0
FREQ_OFFSET
0000 0000, RO
Frequency Offset:
Frequency offset value loaded from the DSP following assertion of the
SAMPLE_FREQ control bit. The Frequency Offset or Frequency
Control value is a twos-complement signed value in units of
approximately 5.1562 ppm. The range is as follows:
0x7F = +655 ppm
0x00 = 0 ppm
0x80 = -660 ppm
www.national.com
RESERVED: Writes ignored, read as 0.
72
This register contains control for the Time Domain Reflectometry (TDR) cable diagnostics. The TDR cable diagnostics sends pulses
down the cable and captures reflection data to be used to estimate cable length and detect certain cabling faults.
TABLE 41. TDR Control Register (TDR_CTRL), address 0x16
Bit
Bit Name
Default
Description
15
TDR_ENABLE
0, RW
TDR Enable:
Enable TDR mode. This forces the powerup state to the correct operating
condition for sending and receiving TDR pulses.
14
TDR_100Mb
0, RW
TDR 100Mb:
Sets the TDR controller to use the 100 Mb Transmitter. This allows for
sending pulse widths in multiples of 8ns. Pulses in 100 Mb mode will
alternate between positive pulses and negative pulses.
Default operation uses the 10 Mb Link Pulse generator. Pulses may
include just the 50 ns pre-emphasis portion of the pulse or the 100 ns full
link pulse (as controlled by setting TDR Width).
13
TX_CHANNEL
0, RW
Transmit Channel Select:
Select transmit channel for sending pulses. The pulse can be sent on the
Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
12
RX_CHANNEL
0, RW
Receive Channel Select:
Select receive channel for detecting pulses. The pulse can be monitored
on the Transmit or Receive pair.
0 : Transmit channel
1 : Receive channel
11
SEND_TDR
0, RW/SC
Send TDR Pulse:
Setting this bit will send a TDR pulse and enable the monitor circuit to
capture the response. This bit will automatically clear when the capture
is complete.
10:8
TDR_WIDTH
000, RW
TDR Pulse Width:
Pulse width in clocks for the transmitted pulse. In 100 Mb mode, pulses
are in 8 ns increments. In 10 Mb mode, pulses are in 50 ns increments,
but only 50 ns or 100 ns pulses can be sent. Sending a pulse of 0 width
will not transmit a pulse, but allows for baseline testing.
7
TDR_MIN_MODE
0, RW
Min/Max Mode control:
This bit controls direction of the pulse to be detected. Default looks for a
positive peak. Threshold and peak values will be interpreted
appropriately based on this bit.
0 : Max Mode, detect positive peak
1 : Min Mode, detect negative peak
RESERVED: Must be zero.
6
RESERVED
0, RW
5:0
RX_THRESHOLD
10 0000, RW
RX Threshold:
This value provides a threshold for measurement to the start of a peak.
If Min Mode is set to 0, data must be greater than this value to trigger a
capture. If Min Mode is 1, data must be less than this value to trigger a
capture. Data ranges from 0x00 to 0x3F, with 0x20 as the midpoint.
Positive data is greater than 0x20, negative data is less than 0x20.
73
www.national.com
DP83630
14.4.3 TDR Control Register (TDR_CTRL), Page 2
DP83630
14.4.4 TDR Window Register (TDR_WIN), Page 2
This register contains sample window control for the Time Domain Reflectometry (TDR) cable diagnostics. The two values contained in this register specify the beginning and end times for the window to monitor the response to the transmitted pulse. Time
values are in 8 ns increments. This provides a method to search for multiple responses and also to screen out the initial outgoing
pulse.
TABLE 42. TDR Window Register (TDR_WIN), address 0x17
Bit
Bit Name
Default
15:8
TDR_START
0000 0000, RW
TDR Start Window:
Specifies start time for monitoring TDR response.
Description
7:0
TDR_STOP
0000 0000, RW
TDR Stop Window:
Specifies stop time for monitoring TDR response. The Stop Window
should be set to a value greater than or equal to the Start Window.
14.4.5 TDR Peak Register (TDR_PEAK), Page 2
This register contains the results of the TDR Peak Detection. Results are valid if the TDR_CTRL[11] is clear following sending the
TDR pulse.
TABLE 43. TDR Peak Register (TDR_PEAK), address 0x18
Bit
Bit Name
Default
15:14
RESERVED
00, RO
13:8
TDR_PEAK
00 0000, RO
7:0
TDR_PEAK_TIME
0000 0000, RO
Description
RESERVED: Writes ignored, read as 0.
TDR Peak Value:
This register contains the peak value measured during the TDR sample
window. If Min Mode control (TDR_CTRL[7]) is 0, this contains the
maximum detected value. If Min Mode control is 1, this contains the
minimum detected value.
TDR Peak Time:
Specifies the time for the first occurrence of the peak value.
14.4.6 TDR Threshold Register (TDR_THR), Page 2
This register contains the results of the TDR Threshold Detection. Results are valid if the TDR_CTRL[11] is clear following sending
the TDR pulse.
TABLE 44. TDR Threshold Register (TDR_THR), address 0x19
Bit
Bit Name
Default
15:9
RESERVED
0000 000, RO
8
TDR_THR_MET
0, RO
TDR Threshold Met:
This bit indicates the TDR threshold was met during the sample window. A
value of 0 indicates the threshold was not met.
7:0
TDR_THR_TIME
0000 0000, RO
TDR Threshold Time:
Specifies the time for the first data that met the TDR threshold. This field is
only valid if the threshold was met.
www.national.com
Description
RESERVED: Writes ignored, read as 0.
74
The Variance Control and Data Registers provide control and status for the Cable Signal Quality Estimation function. The Cable
Signal Quality Estimation allows a simple method of determining an approximate Signal-to-Noise Ratio for the 100 Mb receiver.
This register contains the programmable controls and status bits for the variance computation, which can be used to make a simple
Signal-to-Noise Ratio estimation.
TABLE 45. Variance Control Register (VAR_CTRL), address 0x1A
Bit
Bit Name
Default
15
VAR_RDY
0, RO
Description
14:4
RESERVED
3
VAR_FREEZE
0, RW
Freeze Variance Registers:
Freeze VAR_DATA register.
This bit is ensures that VAR_DATA register is frozen for software reads. This bit
is automatically cleared after two consecutive reads of VAR_DATA.
2:1
VAR_TIMER
00, RW
Variance Computation Timer (in ms):
Selects the Variance computation timer period. After a new value is written,
computation is automatically restarted. New variance register values are loaded
after the timer elapses.
Var_Timer = 0 => 2 ms timer (default)
Var_Timer = 1 => 4 ms timer
Var_Timer = 2 => 6 ms timer
Var_Timer = 3 => 8 ms timer
Time units are actually 217 cycles of an 8 ns clock, or 1.048576 ms.
0
VAR_ENABLE
0, RW
Variance Enable:
Enable Variance computation. Off by default.
Variance Data Ready Status:
Indicates new data is available in the Variance data register. This bit will be
automatically cleared after two consecutive reads of VAR_DATA.
000 0000 0000, RO RESERVED: Writes ignored, read as 0.
14.4.8 Variance Data Register (VAR_DATA), Page 2
This register contains the 32-bit Variance Sum. The contents of the data are valid only when VAR_RDY is asserted in the
VAR_CTRL register. Upon detection of VAR_RDY asserted, software should set the VAR_FREEZE bit in the VAR_CTRL register
to prevent loading of a new value into the VAR_DATA register. Since the Variance Data value is 32-bits, two reads of this register
are required to get the full value.
TABLE 46. Variance Data Register (VAR_DATA), address 0x1B
Bit
Bit Name
Default
Description
15:0
VAR_DATA
0000 0000 0000
0000, RO
Variance Data:
Two reads are required to return the full 32-bit Variance Sum value. Following
setting the VAR_FREEZE control, the first read of this register will return the low
16 bits of the Variance data. A second read will return the high 16 bits of Variance
data.
75
www.national.com
DP83630
14.4.7 Variance Control Register (VAR_CTRL), Page 2
DP83630
14.4.9 Link Quality Monitor Register (LQMR), Page 2
This register contains the controls for the Link Quality Monitor function. The Link Quality Monitor provides a mechanism for programming a set of thresholds for DSP parameters. If the thresholds are violated, an interrupt will be asserted if enabled in the
MISR. Monitor control and status are available in this register, while the LQDR register controls read/write access to threshold
values and current parameter values. Reading the LQMR register clears warning bits and re-arms the interrupt generation. In
addition, this register provides a mechanims for allowing automatic reset of the 100 Mb link based on the Link Quality Monitor
status.
TABLE 47. Link Quality Monitor Register (LQMR), address 0x1D
Bit
Bit Name
Default
15
LQM_ENABLE
0, RW
Link Quality Monitor Enable:
Enables the Link Quality Monitor. The enable is qualified by having a valid 100
Mb link. In addition, the individual thresholds can be disabled by setting to the
maximum or minimum values.
14
RESTART_ON_FC
0, RW
Restart on Frequency Control Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the
threshold violation will also result in a drop in Link status.
13
RESTART_ON
_FREQ
0, RW
Restart on Frequency Offset Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Offset Threshold violation. If the SD_Option bit, PCSR[8], is set to 0,
the threshold violation will also result in a drop in Link status.
12
RESTART_ON
_DBLW
0, RW
Restart on DBLW Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a DBLW
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
11
RESTART_ON
_DAGC
0, RW
Restart on DAGC Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a DAGC
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
10
RESTART_ON_C1
0, RW
Restart on C1 Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a C1
Threshold violation. If the SD_Option bit, PCSR[8], is set to 0, the threshold
violation will also result in a drop in Link status.
9
FC_HI_WARN
0, RO/COR
Frequency Control High Warning:
This bit indicates the Frequency Control High Threshold was exceeded. This
register bit will be cleared on read.
8
FC_LO_WARN
0, RO/COR
Frequency Control Low Warning:
This bit indicates the Frequency Control Low Threshold was exceeded. This
register bit will be cleared on read.
7
FREQ_HI_WARN
0, RO/COR
Frequency Offset High Warning:
This bit indicates the Frequency Offset High Threshold was exceeded. This
register bit will be cleared on read.
6
FREQ_LO_WARN
0, RO/COR
Frequency Offset Low Warning:
This bit indicates the Frequency Offset Low Threshold was exceeded. This
register bit will be cleared on read.
5
DBLW_HI_WARN
0, RO/COR
DBLW High Warning:
This bit indicates the DBLW High Threshold was exceeded. This register bit will
be cleared on read.
4
DBLW_LO_WARN
0, RO/COR
DBLW Low Warning:
This bit indicates the DBLW Low Threshold was exceeded. This register bit will
be cleared on read.
3
DAGC_HI_WARN
0, RO/COR
DAGC High Warning:
This bit indicates the DAGC High Threshold was exceeded. This register bit will
be cleared on read.
www.national.com
Description
76
Bit Name
Default
Description
2
DAGC_LO_WARN
0, RO/COR
DAGC Low Warning:
This bit indicates the DAGC Low Threshold was exceeded. This register bit will
be cleared on read.
1
C1_HI_WARN
0, RO/COR
C1 High Warning:
This bit indicates the DEQ C1 High Threshold was exceeded. This register bit will
be cleared on read.
0
C1_LO_WARN
0, RO/COR
C1 Low Warning:
This bit indicates the DEQ C1 Low Threshold was exceeded. This register bit will
be cleared on read.
77
www.national.com
DP83630
Bit
DP83630
14.4.10 Link Quality Data Register (LQDR), Page 2
This register provides read/write control of thresholds for the 100 Mb Link Quality Monitor function. The register also provides a
mechanism for reading current adapted parameter values. Threshold values may not be written if the device is powered-down.
TABLE 48. Link Quality Data Register (LQDR), address 0x1E
Bit
Bit Name
Default
15:14
RESERVED
00, RO
RESERVED: Writes ignored, read as 0.
13
SAMPLE_PARAM
0, RW
Sample DSP Parameter:
Setting this bit to a 1 enables reading of current parameter values and initiates
sampling of the parameter value. The parameter to be read is selected by the
LQ_PARAM_SEL bits.
12
WRITE_LQ_THR
0, RW
Write Link Quality Threshold:
Setting this bit will cause a write to the Threshold register selected by
LQ_PARAM_SEL and LQ_THR_SEL. The data written is contained in
LQ_THR_DATA. This bit will always read back as 0.
11:9
LQ_PARAM_SEL
000, RW
Link Quality Parameter Select:
This 3-bit field selects the Link Quality Parameter. This field is used for sampling
current parameter values as well as for reads/writes to Threshold values. The
following encodings are available:
000: DEQ_C1
001: DAGC
010: DBLW
011: Frequency Offset
100: Frequency Control
101: Variance most significant bits 31:16
8
LQ_THR_SEL
0, RW
Link Quality Threshold Select:
This bit selects the Link Quality Threshold to be read or written. A 0 selects the
Low threshold, while a 1 selects the high threshold. When combined with the
LQ_PARAM_SEL field, the following encodings are available
{LQ_PARAM_SEL, LQ_THR_SEL}:
000,0: DEQ_C1 Low
000,1: DEQ_C1 High
001,0: DAGC Low
001,1: DAGC High
010,0: DBLW Low
010,1: DBLW High
011,0: Frequency Offset Low
011,1: Frequency Offset High
100,0: Frequency Control Low
100,1: Frequency Control High
101,0: Variance High bits 7:0 (Variance bits 23:16)
101,1: Variance High bits 15:8 (Variance bits 31:24)
7:0
LQ_THR_DATA
1000 0000, RW
Link Quality Threshold Data:
The operation of this field is dependent on the value of the SAMPLE_PARAM
bit.
If SAMPLE_PARAM = 0:
On a write, this value contains the data to be written to the selected Link Quality
Threshold register.
On a read, this value contains the current data in the selected Link Quality
Threshold register.
If SAMPLE_PARAM = 1:
On a read, this value contains the sampled parameter value. This value will
remain unchanged until a new read sequence is started.
www.national.com
Description
78
This register contains additional controls for the Link Quality Monitor function. The Link Quality Monitor provides a mechanism for
programming a set of thresholds for DSP parameters. If the thresholds are violated, an interrupt will be asserted if enabled in the
MISR. Monitor control and status are available in this register, while the LQDR register controls read/write access to threshold
values and current parameter values. Reading of LQMR2 register clears its warning bits but does NOT re-arm the interrupt generation; LQMR must be read to re-arm interrupt generation. In addition, this register provides a mechanism for allowing automatic
reset of the 100 Mb link based on the Link Quality Monitor variance status.
TABLE 49. Link Quality Monitor Register 2 (LQMR2), address 0x1F
Bit
Bit Name
Default
15:11
RESERVED
0000 0, RO
10
RESTART_ON_VAR
0, RW
9:2
RESERVED
00 0000 00, RO
1
VAR_HI_WARN
0, RO/COR
0
RESERVED
0, RO
Description
Reserved: Writes ignored, Read as 0
Restart on Variance Warning:
Allow automatic reset of DSP and restart of 100 Mb Adaption on detecting a
Frequency Offset Threshold violation. If the SD_Option bit, PCSR[8], is set to 0,
the threshold violation will also result in a drop in Link status.
Reserved: Writes ignored, Read as 0
Variance High Warning:
This bit indicates the Variance High Threshold was exceeded. This register bit will
be cleared on read.
Reserved: Writes ignored, Read as 0
79
www.national.com
DP83630
14.4.11 Link Quality Monitor Register 2 (LQMR2), Page 2
DP83630
14.5 PTP 1588 BASE REGISTERS - PAGE 4
Page 4 PTP 1588 Base Registers are accessible by setting bits [2:0] = 100 of PAGESEL (13h).
14.5.1 PTP Control Register (PTP_CTL), Page 4
This register provides basic control of the PTP 1588 operation.
TABLE 50. PTP Control Register (PTP_CTL), address 0x14
Bit
Bit Name
Default
15:13
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
12:10
TRIG_SEL
000, RW
PTP Trigger Select:
This field selects the Trigger for loading control information or for enabling the
Trigger.
9
TRIG_DIS
0, RW/SC
Disable PTP Trigger:
Setting this bit will disable the selected Trigger. This bit does not indicate Disable
status for Triggers. The PTP Trigger Status Register should be used to determine
Trigger Status. This bit is self-clearing and will always read back as 0.
Disabling a Trigger will not disconnect it from a GPIO pin. The Trigger value will
still be driven to the GPIO if the Trigger is assigned to a GPIO.
8
TRIG_EN
0, RW/SC
Enable PTP Trigger:
Setting this bit will enable the selected Trigger. This bit does not indicate Enable
status for Triggers. The PTP Trigger Status Register should be used to determine
Trigger Status. This bit is self-clearing and will always read back as 0.
7
TRIG_READ
0, RW/SC
Read PTP Trigger:
Setting this bit will begin the Trigger Read process. The Trigger is selected based
on the setting of the TRIG_SEL bits in this register. Upon setting this bit,
subsequent reads of the PTP_TDR will return the Trigger Control values. Fields
are read in the same order as written.
6
TRIG_LOAD
0, RW/SC
Load PTP Trigger:
Setting this bit will disable the selected Trigger and begin the Trigger load process.
The Trigger is selected based on the setting of the TRIG_SEL bits in this register.
Upon setting this bit, subsequent writes to the PTP_TDR will set the Trigger
Control fields for the selected Trigger. The Trigger Load is completed once all
fields have been written, or the TRIG_EN bit has been set in this register. This bit
is self-clearing and will read back as 0 when the Trigger Load is completed either
by writing all Trigger Control fields, or by setting the Trigger Enable.
5
PTP_RD_CLK
0, RW/SC
Read PTP Clock:
Setting this bit will cause the device to sample the PTP Clock time value. The time
value will be made available for reading through the PTP_TDR register. This bit
is self-clearing and will always read back as 0.
4
PTP_LOAD_CLK
0, RW/SC
Load PTP Clock:
Setting this bit will cause the device to load the PTP Clock time value from data
previously written to the PTP_TDR register. This bit is self-clearing and will always
read back as 0.
3
PTP_STEP_CLK
0, RW/SC
Step PTP Clock:
Setting this bit will cause the device to add a value to the PTP Clock. The value
to be added is the value previously written to the PTP_TDR register. This bit is
selfclearing and will always read back as 0.
2
PTP_ENABLE
0, RW
Enable PTP Clock:
Setting this bit will enable the PTP Clock. Reading this bit will return the current
enabled value. Writing a 0 to this bit will have no effect.
www.national.com
Description
80
Bit Name
Default
Description
1
PTP_DISABLE
0, RW/SC
Disable PTP Clock:
Setting this bit will disable the PTP Clock. Writing a 0 to this bit will have no effect.
This bit is self-clearing and will always read back as 0.
0
PTP_RESET
0, RW
Reset PTP Clock:
Setting this bit will reset the PTP Clock and associated logic. In addition, the 1588
registers will be reset, with the exception of the PTP_COC and PTP_CLKSRC
registers. Unlike other bits in this register, this bit is not self-clearing and must be
written to 0 to release the clock and logic from reset.
81
www.national.com
DP83630
Bit
DP83630
14.5.2 PTP Time Data Register (PTP_TDR), Page 4
This register provides a mechanism for reading and writing the 1588 Time and Trigger Control values. The function of this register
is determined by controls in the PTP_CTL register.
TABLE 51. PTP Time Data Register (PTP_TDR), address 0x15
Bit
Bit Name
Default
Description
15:0
TIME_DATA
XXXX XXXX XXXX
XXXX, RO
XXXX XXXX XXXX
XXXX, WO
Time Data:
On Reads, successively returns 16-bit values of the Clock time or Trigger Control
information as selected by controls in the PTP Control Register. Additional reads
beyond the avaliable fields will always return 0.
On Writes, successively stores the 16-bit values of Clock time or Trigger Control
Information as selected by controls in the PTP Control Register.
14.5.3 PTP Status Register (PTP_STS), Page 4
This register provides basic status and interrupt control for the PTP 1588 operation.
TABLE 52. PTP Status Register (PTP_STS), address 0x16
Bit
Bit Name
Default
15:12
RESERVED
0000, RO
11
TXTS_RDY
0, RO
Transmit Timestamp Ready:
A Transmit Timestamp is available for an outbound PTP Message. This bit will be
cleared upon read of the Transmit Timestamp if no other timestamps are ready.
10
RXTS_RDY
0, RO
Receive Timestamp Ready:
A Receive Timestamp is available for an inbound PTP Message. This bit will be
cleared upon read of the Receive Timestamp if no other timestamps are ready.
9
TRIG_DONE
0, RO/COR
PTP Trigger Done:
A PTP Trigger has occured. This bit will be cleared upon read. This bit will only
be set if Trigger Notification is turned on for the Trigger through the Trigger
Configuration Registers.
8
EVENT_RDY
0, RO
PTP Event Timestamp Ready:
A PTP Event Timestamp is available. This bit will be cleared upon read of the PTP
Event Status Register if no other event timestamps are ready.
7:4
RESERVED
0000, RO
3
TXTS_IE
0, RW
Transmit Timestamp Interrupt Enable:
Enable Interrupt on Transmit Timestamp Ready.
2
RXTS_IE
0, RW
Receive Timestamp Interrupt Enable:
Enable Interrupt on Receive Timestamp Ready.
1
TRIG_IE
0, RW
Trigger Interrupt Enable:
Enable Interrupt on Trigger Completion.
0
EVENT_IE
0, RW
Event Interrupt Enable:
Enable Interrupt on Event Timestamp Ready.
www.national.com
Description
Reserved: Writes ignored, Read as 0
Reserved: Writes ignored, Read as 0
82
This register provides status of the PTP 1588 Triggers. The bits in this register indicate the current status of each of the Trigger
modules. The error bits will be set if the associated notification enable (TRIGN_NOTIFY) is set in the PTP Trigger Configuration
Registers.
TABLE 53. PTP Trigger Status Register (PTP_TSTS), address 0x17
Bit
Bit Name
Default
Description
15
TRIG7_ERROR
0, RO/SC
Trigger 7 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
14
TRIG7_ACTIVE
0, RO/SC
Trigger 7 Active:
This bit indicates the Trigger is enabled and has not completed.
13
TRIG6_ERROR
0, RO/SC
Trigger 6 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
12
TRIG6_ACTIVE
0, RO/SC
Trigger 6 Active:
This bit indicates the Trigger is enabled and has not completed.
11
TRIG5_ERROR
0, RO/SC
Trigger 5 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
10
TRIG5_ACTIVE
0, RO/SC
Trigger 5 Active:
This bit indicates the Trigger is enabled and has not completed.
9
TRIG4_ERROR
0, RO/SC
Trigger 4 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
8
TRIG4_ACTIVE
0, RO/SC
Trigger 4 Active:
This bit indicates the Trigger is enabled and has not completed.
7
TRIG3_ERROR
0, RO/SC
Trigger 3 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
6
TRIG3_ACTIVE
0, RO/SC
Trigger 3 Active:
This bit indicates the Trigger is enabled and has not completed.
5
TRIG2_ERROR
0, RO/SC
Trigger 2 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
4
TRIG2_ACTIVE
0, RO/SC
Trigger 2 Active:
This bit indicates the Trigger is enabled and has not completed.
3
TRIG1_ERROR
0, RO/SC
Trigger 1 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
2
TRIG1_ACTIVE
0, RO/SC
Trigger 1 Active:
This bit indicates the Trigger is enabled and has not completed.
1
TRIG0_ERROR
0, RO/SC
Trigger 0 Error:
This bit indicates the Trigger was improperly programmed to trigger at a time prior
to the current time. This bit will be cleared when the Trigger is disabled and/ or
re-armed.
0
TRIG0_ACTIVE
0, RO/SC
Trigger 0 Active:
This bit indicates the Trigger is enabled and has not completed.
83
www.national.com
DP83630
14.5.4 PTP Trigger Status Register (PTP_TSTS), Page 4
DP83630
14.5.5 PTP Rate Low Register (PTP_RATEL), Page 4
This register contains the low 16-bits of the PTP Rate control. The PTP Rate Control indicates a positive or negative adjustment
to the reference clock period in units of 2-32 ns. On each reference clock cycle, the PTP Clock will be adjusted by adding
REF_CLK_PERIOD +/- PTP_RATE. The PTP Rate should be written as PTP_RATEH, followed by PTP_RATEL. The rate will take
effect on the write to the PTP_RATEL register.
TABLE 54. PTP Rate Low Register (PTP_RATEL), address 0x18
Bit
Bit Name
Default
Description
15:0
PTP_RATE_LO
0000 0000 0000
0000, RW
PTP Rate Low 16-bits:
Writing to this register will set the low 16-bits of the Rate Control value. The Rate
Control value is in units of 2-32 ns. Upon writing to this register, the full Rate Control
value will be loaded to the device.
www.national.com
84
This register contains the upper bits of the PTP Rate control. In addition, it contains a direction control to indicate whether the
device is operating faster or slower than the reference clock frequency. When setting the PTP Rate, this register should be written
first, followed by a write to the PTP_RATEL register. The rate will take effect on the write to the PTP_RATEL register.
TABLE 55. PTP Rate High Register (PTP_RATEH), address 0x19
Bit
Bit Name
Default
Description
15
PTP_RATE_DIR
0, RW
PTP Rate Direction:
The setting of this bit controls whether the device will operate at a higher or lower
frequency than the reference clock.
0 : Higher Frequency. The PTP_RATE value will be added to the clock on every
cycle.
1 : Lower Frequency. The PTP_RATE value will be subtracted from the clock on
every cycle.
14
PTP_TMP_RATE
0, RW
PTP Temporary Rate:
Setting this bit will cause the rate to be applied to the clock for the duration set in
the PTP Temporary Rate Duration Register (PTP_TRD).
1 : Temporary Rate
0 : Normal Rate
13:10
RESERVED
9:0
PTP_RATE_HI
00 00, RO
Reserved: Writes ignored, Read as 0
00 0000 0000, RW PTP Rate High 10-bits:
Writing to this register will set the high 10-bits of the Rate Control value. The Rate
Control value is in units of 2-32 ns.
14.5.7 PTP Read Checksum (PTP_RDCKSUM), Page 4
This register keeps a running one’s complement checksum of 16-bit read data values for valid Page 4 read accesses. Clear the
checksum on a read to this register; read data from this register is not accumulated in the read checksum since the register is
cleared on read. However, read data from the write checksum register is accumulated to allow cross checking. Checksums are
not accumulated for PHY Control Frame register accesses, but are cleared on management or PHY Control Frame reads.
TABLE 56. PTP Read Checksum (PTP_RDCKSUM), address 0x1A
Bit
Bit Name
15:0
RD_CKSUM
Default
Description
XXXX XXXX XXXX PTP Page 4 Read Checksum.
XXXX, RO/ COR
14.5.8 PTP Write Checksum (PTP_WRCKSUM), Page 4
This register keeps a running one’s complement checksum of 16-bit write data values for Page 4 write accesses. Clear the checksum on a read. Write data to this register or the read checksum register ARE accumulated in the write checksum to allow cross
checking. Read data from this register is accumulated in the read checksum to allow cross checking. Checksums are not accumulated for PHY Control Frame register accesses, but are cleared on management or PHY Control Frame reads.
TABLE 57. PTP Write Checksum (PTP_WRCKSUM), address 0x1B
Bit
Bit Name
15:0
WR_CKSUM
Default
Description
XXXX XXXX XXXX PTP Page 4 Write Checksum.
XXXX, RO/ COR
85
www.national.com
DP83630
14.5.6 PTP Rate High Register (PTP_RATEH), Page 4
DP83630
14.5.9 PTP Transmit Timestamp Register (PTP_TXTS), Page 4
This register provides a mechanism for reading the Transmit Timestamp. The fields are read in the following order:
•
•
•
•
Timestamp_ns [15:0]
Overflow_cnt[1:0], Timestamp_ns[29:16]
Timestamp_sec[15:0]
Timestamp_sec[31:16]
The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit Timestamp queue. The overflow
counter will stick at a value of three if additional timestamps were missed.
TABLE 58. PTP Transmit Timestamp Register (PTP_TXTS), address 0x1C
Bit
Bit Name
Default
15:0
PTP_TX_TS
0000 0000 0000
0000, RO
Description
PTP Transmit Timestamp:
Reading this register will return the Transmit Timestamp in four 16-bit reads.
14.5.10 PTP Receive Timestamp Register (PTP_RXTS), Page 4
This register provides a mechanism for reading the Receive Timestamp and identification information. The fields are read in the
following order:
•
•
•
•
•
•
Timestamp_ns [15:0]
Overflow_cnt[1:0], Timestamp_ns[29:16]
Timestamp_sec[15:0]
Timestamp_sec[31:16]
sequenceId[15:0]
messageType[3:0], source_hash[11:0]
The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit Timestamp queue. The overflow
counter will stick at a value of three if additional timestamps were missed.
TABLE 59. PTP Receive Timestamp Register (PTP_RXTS), address 0x1D
Bit
Bit Name
Default
15:0
PTP_RX_TS
0000 0000 0000
0000, RO
www.national.com
Description
PTP Receive Timestamp:
Reading this register will return the Receive Timestamp in four 16-bit reads.
86
This register provides Status for the Event Timestamp unit. Reading this register provides status for the next Event Timestamp
contained in the Event Data Register. If this register is 0, no Event Timestamp is available in the Event Data Register. Reading
this register will automatically move to the next Event in the queue.
TABLE 60. PTP Event Status Register (PTP_ESTS), address 0x1E
Bit
Bit Name
Default
Description
15:11
RESERVED
0000 0, RO
Reserved: Writes ignored, Read as 0
10:8
EVNTS_MISSED
000, RO/SC
Event Missed:
Indicates number of events have been missed prior to this timestamp for the
EVNT_NUM indicated. This count value will stick at 7 if more than 7 events are
missed.
7:6
EVNT_TS_LEN
00, RO/SC
Event Timestamp Length:
Indicates length of the Timestamp field in 16-bit words minus 1. Although all fields
are available, this indicates how many of the fields contain data different from the
previous Event Timestamp. This allows software to avoid reading more significant
fields if they have not changed since the previous timestamp. This field is valid
for both single and multiple events. The following shows the number of least
significant fields which have new data for each setting of TS_LENGTH:
00 : One 16-bit field is new (Timestamp_ns[15:0])
01 : Two 16-bit fields are new
10 : Three 16-bit fields are new
11 : All four 16-bit fields are new
5
EVNT_RF
0, RO/SC
Event Rise/Fall direction:
Indicates whether the event is a rise or falling event. If the MULT_EVNT bit is set
to 1, this bit indicates the Rise/Fall direction for the event indicated by
EVNT_NUM.
0 = Falling edge detected
1 = Rising edge detected
4:2
EVNT_NUM
000, RO/SC
Event Number:
Indicates Event Timestamp Unit which detected an event. If the MULT_EVNT bit
is set to 0, this indicates the lowest event number captured. If events have been
missed prior to this timestamp, it indicates the lowest event number captured
which had at least one missed event.
1
MULT_EVNT
0, RO/SC
Multiple Event Detect:
Indicates multiple events were detected at the same time. If multiple events are
detected, an extended event status field is available as the first data read from
the Event Data Register.
0 = Single event detected
1 = Multiple events detected
0
EVENT_DET
0, RO/SC
PTP Event Detected:
Indicates an Event has been detected by one of the Event Timestamp Units.
87
www.national.com
DP83630
14.5.11 PTP Event Status Register (PTP_ESTS), Page 4
DP83630
14.5.12 PTP Event Data Register (PTP_EDATA), Page 4
This register provides a mechanism for reading the Event Timestamp and extended event status. If present, the extended event
status is read prior to reading the Event Timestamp. Presence of the Extended Event Status field is indicated by the MULT_EVNT
bit in the PTP Event Status Register. The timestamp consists of four 16-bit fields. This register contains a valid timestamp if the
PTP_ESTS register indicates an Event Timestamp is available. Not all fields have to be read for each timestamp. For example, if
the EVNT_TS_LEN indicates the seconds field has not changed from the previous event, software may skip that read. Reading
the PTP_ESTS register will cause the device to move to the next available timestamp.
The fields are read in the following order:
•
•
•
•
•
Extended Event Status[15:0] (only available if PTP_ESTS indicates detection of multiple events)
Timestamp_ns [15:0]
Timestamp_ns[29:16] (upper 2 bits are always 0)
Timestamp_sec[15:0]
Timestamp_sec[31:16]
For Extended Event Status, the following definition is used for the PTP Event Data Register:
TABLE 61. PTP Event Data Register (PTP_EDATA), address 0x1F
Bit
Bit Name
Default
15
E7_RISE
0, RO/SC
Rise/Fall edge direction for Event 7:
Indicates direction of Event 7
0 = Fall
1 = Rise
14
E7_DET
0, RO/SC
Event 7 detected:
Indicates Event 7 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
13
E6_RISE
0, RO/SC
Rise/Fall edge direction for Event 6:
Indicates direction of Event 6
0 = Fall
1 = Rise
12
E6_DET
0, RO/SC
Event 6 detected:
Indicates Event 6 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
11
E5_RISE
0, RO/SC
Rise/Fall edge direction for Event 5:
Indicates direction of Event 5
0 = Fall
1 = Rise
10
E5_DET
0, RO/SC
Event 5 detected:
Indicates Event 5 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
9
E4_RISE
0, RO/SC
Rise/Fall edge direction for Event 4:
Indicates direction of Event 4
0 = Fall
1 = Rise
8
E4_DET
0, RO/SC
Event 4 detected:
Indicates Event 4 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
7
E3_RISE
0, RO/SC
Rise/Fall edge direction for Event 3:
Indicates direction of Event 3
0 = Fall
1 = Rise
6
E3_DET
0, RO/SC
Event 3 detected:
Indicates Event 3 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
5
E2_RISE
0, RO/SC
Rise/Fall edge direction for Event 2:
Indicates direction of Event 2
0 = Fall
1 = Rise
www.national.com
Description
88
Bit Name
Default
Description
4
E2_DET
0, RO/SC
Event 2 detected:
Indicates Event 2 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
3
E1_RISE
0, RO/SC
Rise/Fall edge direction for Event 1:
Indicates direction of Event 1
0 = Fall
1 = Rise
2
E1_DET
0, RO/SC
Event 1 detected:
Indicates Event 1 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
1
E0_RISE
0, RO/SC
Rise/Fall edge direction for Event 0:
Indicates direction of Event 0
0 = Fall
1 = Rise
0
E0_DET
0, RO/SC
Event 0 detected:
Indicates Event 0 detected a rising or falling edge at the time contained in the
PTP_EDATA register timestamp.
For timestamp fields, the following definition is used for the PTP Event Data Register:
TABLE 62. PTP Event Data Register (PTP_EDATA), address 0x1F
Bit
Bit Name
15:0
PTP_EVNT_TS
Default
Description
XXXX XXXX XXXX PTP Event Timestamp:
XXXX, RO
Reading this register will return 16 bits of the Event Timestamp.
89
www.national.com
DP83630
Bit
DP83630
14.6 PTP 1588 CONFIGURATION REGISTERS - PAGE 5
Page 5 PTP 1588 Configuration Registers are accessible by setting bits [2:0] = 101 of PAGESEL (13h).
14.6.1 PTP Trigger Configuration Register (PTP_TRIG), Page 5
This register provides basic configuration for IEEE 1588 Triggers. To write configuration to a Trigger, set the TRIG_WR bit along
with the TRIG_SEL and other control information. To read configuration from a Trigger, set the TRIG_SEL encoding to the Trigger
desired, and set the TRIG_WR bit to 0. The subsequent read of the PTP_TRIG register will return the configuration information.
TABLE 63. PTP Trigger Configuration Register (PTP_TRIG), address 0x14
Bit
Bit Name
Default
Description
15
TRIG_PULSE
0, RW
Trigger Pulse:
Setting this bit will cause the Trigger to generate a Pulse rather than a single rising
or falling edge.
14
TRIG_PER
0, RW
Trigger Periodic:
Setting this bit will cause the Trigger to generate a periodic signal. If this bit is 0,
the Trigger will generate a single Pulse or Edge depending on the Trigger Control
settings.
13
TRIG_IF_LATE
0, RW
Trigger-if-late Control:
Setting this bit will allow an immediate Trigger in the event the Trigger is
programmed to a time value which is less than the current time. This provides a
mechanism for generating an immediate trigger or to immediately begin
generating a periodic signal. For a periodic signal, no notification be generated if
this bit is set and a Late Trigger occurs.
12
TRIG_NOTIFY
0, RW
Trigger Notification Enable:
Setting this bit will enable Trigger status to be reported on completion of a Trigger
or on an error detection due to late trigger. If Trigger interrupts are enabled, the
notification will also result in an interrupt being generated.
11:8
TRIG_GPIO
0000, RW
7
TRIG_TOGGLE
0, RW
Trigger GPIO Connection:
Setting this field to a non-zero value will connect the Trigger to the associated
GPIO pin. Valid settings for this field are 1 thru 12.
Trigger Toggle Mode Enable:
Setting this bit will put the trigger into toggle mode. In toggle mode, the initial value
will be ignored and the trigger output will be toggled at the trigger time.
6:4
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
3:1
TRIG_CSEL
000, RW
Trigger Configuration Select:
This field selects the Trigger for configuration read or write.
0
TRIG_WR
0, RW/SC
Trigger Configuration Write:
Setting this bit will generate a Configuration Write to the selected Trigger. This bit
will always read back as 0.
www.national.com
90
This register provides basic configuration for IEEE 1588 Events. To write configuration to an Event Timestamp Unit, set the
EVNT_WR bit along with the EVNT_SEL and other control information. To read configuration from an Event Timestamp Unit, set
the EVNT_SEL encoding to the Event desired, and set the EVNT_WR bit to 0. The subsequent read of the PTP_EVNT register
will return the configuration information.
TABLE 64. PTP Event Configuration Register (PTP_EVNT), address 0x15
Bit
Bit Name
Default
15
RESERVED
0, RO
Reserved: Writes ignored, Read as 0
Description
14
EVNT_RISE
0, RW
Event Rise Detect Enable:
Enable Detection of Rising edge on Event input.
13
EVNT_FALL
0, RW
Event Fall Detect Enable:
Enable Detection of Falling edge on Event input.
12
EVNT_SINGLE
0, RW
Single Event Capture: Setting this bit to a 1 will enable single event capture
operation. The EVNT_RISE and EVNT_FALL enables will be cleared upon a valid
event timestamp capture.
11:8
EVNT_GPIO
0000, RW
Event GPIO Connection:
Setting this field to a non-zero value will connect the Event to the associated GPIO
pin. Valid settings for this field are 1 thru 12.
7:4
RESERVED
0000, RO
Reserved: Writes ignored, Read as 0
3:1
EVNT_SEL
000, RW
Event Select:
This field selects the Event Timestamp Unit for configuration read or write.
0
EVNT_WR
0, RW
Event Configuration Write:
Setting this bit will generate a Configuration Write to the selected Event
Timestamp Unit.
91
www.national.com
DP83630
14.6.2 PTP Event Configuration Register (PTP_EVNT), Page 5
DP83630
14.6.3 PTP Transmit Configuration Register 0 (PTP_TXCFG0), Page 5
This register provides configuration for IEEE 1588 Transmit Timestamp operation.
TABLE 65. PTP Transmit Configuration Register 0 (PTP_TXCFG0), address 0x16
Bit
Bit Name
Default
Description
15
SYNC_1STEP
0, RW
Sync Message One-Step Enable:
Enable automatic insertion of timestamp into transmit Sync Messages. Device will
automatically parse message and insert the timestamp in the correct location.
UPD checksum and CRC fields will be regenerated.
14
RESERVED
0, RO
Reserved: Writes ignored, Read as 0
13
DR_INSERT
0, RW
Insert Delay_Req Timestamp in Delay_Resp:
If this bit is set to a 1, the device insert the timestamp for transmitted Delay_Req
messages into inbound Delay_Resp messages. The most recent timestamp will
be used for any inbound Delay_Resp message. The receive timestamp insertion
logic must be enabled through the PTP Receive Configuration Registers.
12
NTP_TS_EN
0, RW
Enable Timestamping of NTP Packets:
If this bit is set to 0, the device will check the UDP protocol field for a PTP Event
message (value 319). If this bit is set to 1, the device will check the UDP protocol
field for an NTP message (value 123). This setting applies to the transmit and
receive packet parsing engines.
11
IGNORE_2STEP
0, RW
Ignore Two_Step flag for One-Step operation:
If this bit is set to a 0, the device will not insert a timestamp if the Two_Step bit is
set in the flags field of the PTP header. If this bit is set to 1, the device will insert
a timestamp independent of the setting of the Two_Step flag.
10
CRC_1STEP
0, RW
Disable checking of CRC for One-Step operation:
If this bit is set to a 0, the device will force a CRC error for One-Step operation if
the incoming frame has a CRC error. If this bit is set to a 1, the device will send
the One- Step frame with a valid CRC, even if the incoming CRC is invalid.
9
CHK_1STEP
0, RW
Enable UDP Checksum correction for One-Step Operation:
Enables correction of the UDP checksum for messages which include insertion
of the timestamp. The checksum is corrected by modifying the last two bytes of
the UDP data. The last two bytes must be transmitted by the MAC as 0’s. This
control must be set for proper IPv6/UDP One-Step operation. This control will
have no effect for Layer2 Ethernet messages.
8
IP1588_EN
0, RW
Enable IEEE 1588 defined IP address filter:
Enable filtering of UDP/IP Event messages using the IANA assigned IP
Destination addresses. If this bit is set to 1, packets with IP Destination addresses
which do not match the IANA assigned addresses will not be timestamped. This
field affects operation for both IPv4 and IPv6. If this field is set to 0, IP destination
addresses will be ignored.
7
TX_L2_EN
0, RW
Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6
TX_IPV6_EN
0, RW
IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5
TX_IPV4_EN
0, RW
IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1
TX_PTP_VER
0 000, RW
0
TX_TS_EN
0, RW
www.national.com
PTP Version:
Enable Timestamp capture for a specific version of the IEEE 1588 specification.
This field may be programmed to any value between 1 and 15 and allows support
for future versions of the IEEE 1588 specification. A value of 0 will disable version
checking (not recommended).
Transmit Timestamp Enable:
Enable Timestamp capture for Transmit.
92
This register provides data and mask fields to filter the first byte in a PTP Message. This function will be disabled if all the mask
bits are set to 0.
TABLE 66. PTP Transmit Configuration Register 1 (PTP_TXCFG1), address 0x17
Bit
Bit Name
Default
Description
15:8
BYTE0_MASK
0000 0000, RW
Byte0 Data:
Bit mask to be used for matching Byte0 of the PTP Message. A one in any bit
enables matching for the associated data bit. If no matching is required, all bits of
the mask should be set to 0.
7:0
BYTE0_DATA
0000 0000, RW
Byte0 Mask:
Data to be used for matching Byte0 of the PTP Message.
14.6.5 PHY Status Frame Configuration Register 0 (PSF_CFG0), Page 5
This register provides configuration for the PHY Status Frame function.
TABLE 67. PHY Status Frame Configuration Register 0 (PSF_CFG0), address 0x18
Bit
Bit Name
Default
Description
15:13
RESERVED
000, RO
Reserved: Writes ignored, Read as 0
12:11
MAC_SRC_ADD
0 0, RW
PHY Status Frame Mac Source Address:
Selects source address as follows:
00 : Use Mac Address [08 00 17 0B 6B 0F]
01 : Use Mac Address [08 00 17 00 00 00]
10 : Use Mac Multicast Dest Address
11 : Use Mac Address [00 00 00 00 00 00]
10:8
MIN_PRE
000, RW
PHY Status Frame Minimum Preamble:
Determines the minimum preamble bytes required for sending packets on the MII
interface. It is recommended that this be set to the smallest value the MAC will
tolerate.
7
PSF_ENDIAN
0, RW
PHY Status Frame Endian Control:
For each 16-bit field in a Status Message, the data will normally be presented in
network byte order (Most significant byte first). If this bit is set to a 1, the byte data
fields will be reversed so that the least significant byte is first.
6
PSF_IPV4
0, RW
PHY Status Frame IPv4 Enable:
This bit controls the type of packet used for PHY Status Frames.
0 = Layer2 Ethernet packets
1 = IPv4 packets.
5
PSF_PCF_RD
0, RW
PHY Control Frame Read PHY Status Frame Enable:
Enable PHY Status Frame delivery of PHY Control Frame read data. Data read
via a PHY Control Frame will be returned in a PHY Status Frame.
4
PSF_ERR_EN
0, RW
PSF Error PHY Status Frame Enable:
Enable PHY Status Frame delivery of PHY Status Frame Errors. This bit will not
independently enable PHY Status Frame operation. One of the other enable bits
must be set for PHY Status Frames to be generated.
3
PSF_TXTS_EN
0, RW
Transmit Timestamp PHY Status Frame Enable:
Enable PHY Status Frame delivery of Transmit Timestamps.
2
PSF_RXTS_EN
0, RW
Receive Timestamp PHY Status Frame Enable:
Enable PHY Status Frame delivery of Receive Timestamps.
1
PSF_TRIG_EN
0, RW
Trigger PHY Status Frame Enable:
Enable PHY Status Frame delivery of Trigger Status.
0
PSF_EVNT_EN
0, RW
Event PHY Status Frame Enable:
Enable PHY Status Frame delivery of Event Timestamps.
93
www.national.com
DP83630
14.6.4 PTP Transmit Configuration Register 1 (PTP_TXCFG1), Page 5
DP83630
14.6.6 PTP Receive Configuration Register 0 (PTP_RXCFG0), Page 5,
This register provides configuration for IEEE 1588 Receive Timestamp operation.
TABLE 68. PTP Receive Configuration Register 0 (PTP_RXCFG0), address 0x19
Bit
Bit Name
Default
Description
15
DOMAIN_EN
0, RW
Domain Match Enable:
If set to 1, the Receive Timestamp unit will require the Domain field to match the
value programmed in the PTP_DOMAIN field of the PTP_RXCFG3 register. If set
to 0, the Receive Timestamp will ignore the PTP_DOMAIN field.
14
ALT_MAST_DIS
0, RW
Alternate Master Timestamp Disable:
Disables timestamp generation if the Alternate_Master flag is set:
1 = Do not generate timestamp if Alternate_Master = 1
0 = Ignore Alternate_Master flag
13
USER_IP_SEL
0, RW
IP Address data select:
Selects portion of IP address accessible through the PTP_RXCFG2 register:
0 = Most Significant Octets
1 = Least Significant Octets
12
USER_IP_EN
0, RW
Enable User-programmed IP address filter:
Enable detection of UDP/IP Event messages using a programmable IP
addresses. The IP Address is set using the PTP_RXCFG2 register.
11
RX_SLAVE
0, RW
Receive Slave Only:
By default, the Receive Timestamp Unit will provide Timestamps for event
messages meeting other requirements. Setting this bit to a 1 will prevent
Delay_Req messages from being Timestamped by requiring that the Control Field
(offset 32 in the PTP message) be set to a value other than 1.
10:8
IP1588_EN
000, RW
Enable IEEE 1588 defined IP address filters:
Enable detection of UDP/IP Event messages using the IANA assigned IP
Destination addresses. This field affects operation for both IPv4 and IPv6. A
Timestamp is captured for the PTP message if the IP destination address matches
the following:
IP1588_EN[0]: Dest IP address = 224.0.1.129
IP1588_EN[1]: Dest IP address = 224.0.1.130-132
IP1588_EN[2]: Dest IP address = 224.0.0.107
7
RX_L2_EN
0, RW
Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6
RX_IPV6_EN
0, RW
IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5
RX_IPV4_EN
0, RW
IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1
RX_PTP_VER
0 000, RW
0
RX_TS_EN
0, RW
www.national.com
PTP Version:
Enable Timestamp capture for a specific version of the IEEE 1588 specification.
This field may be programmed to any value between 1 and 15 and allows support
for future versions of the IEEE 1588 specification. A value of 0 will disable version
checking (not recommended).
Receive Timestamp Enable:
Enable Timestamp capture for Receive.
94
This register provides data and mask fields to filter the first byte in a PTP Message. This function will be disabled if all the mask
bits are set to 0.
TABLE 69. PTP Receive Configuration Register 1 (PTP_RXCFG1), address 0x1A
Bit
Bit Name
Default
Description
15:8
BYTE0_MASK
0000 0000, RW
Byte0 Data:
Bit mask to be used for matching Byte0 of the Receive PTP Message. A one in
any bit enables matching for the associated data bit. If no matching is required,
all bits of the mask should be set to 0.
7:0
BYTE0_DATA
0000 0000, RW
Byte0 Mask:
Data to be used for matching Byte0 of the Receive PTP Message.
14.6.8 PTP Receive Configuration Register 2 (PTP_RXCFG2), Page 5
This register provides for programming an IP address to be used for filtering packets to detect PTP Event Messages. Since the
IPv4 address is 32-bits, to write an IP address, software must write two 16-bit values. The USER_IP_SEL bit in the PTP_RXCFG0
register selects which octects of the IP address are accessible through this register. For example, to write an IP address of
224.0.1.129, software should do the following:
1.
2.
3.
4.
Set USER_IP_SEL bit in PTP_RXCFG0 register to 0
Write 0xE000 (224.00) to PTP_RXCFG2
Set USER_IP_SEL bit in the PTP_RXCFG0 register to 1
Write 0x0181 (01.129) to PTP_RXCFG2
Reading this registerwill return the IP address field selected by USER_IP_SEL.
TABLE 70. PTP Receive Configuration Register 2 (PTP_RXCFG2), address 0x1B
Bit
Bit Name
Default
Description
15:0
IP_ADDR_DATA
0000 0000 0000
0000, RW
Receive IP Address Data:
16-bits of the IP Address field to be read or written. The USER_IP_SEL bit in the
PTP_RXCFG0 Register selects the portion of the IP address is to be read or
written.
95
www.national.com
DP83630
14.6.7 PTP Receive Configuration Register 1 (PTP_RXCFG1), Page 5
DP83630
14.6.9 PTP Receive Configuration Register 3 (PTP_RXCFG3), Page 5
This register provides extended configuration for IEEE 1588 Receive Timestamp operation.
TABLE 71. PTP Receive Configuration Register 3 (PTP_RXCFG3), address 0x1C
Bit
Bit Name
Default
Description
15:12
TS_MIN_IFG
1100, RW
Minimum Inter-frame Gap:
When a Timestamp is appended to a PTP Message, the length of the packet may
get extended. This could reduce the Inter-frame Gap (IFG) between packets by
as much as 8 byte times (640 ns at 100 Mb). This field sets a minimum on the
IFG between packets in number of byte times. If the IFG is set larger than the
actual IFG, preamble bytes of the subsequent packet will get dropped. This value
should be set to the lowest possible value that the attached MAC can support.
11
ACC_UDP
0, RW
Record Timestamp if UDP Checksum Error:
By default, Timestamps will be discarded for packets with UDP Checksum errors.
If this bit is set, then the Timestamp will be made available in the normal manner.
10
ACC_CRC
0, RW
Record Timestamp if CRC Error:
By default, Timestamps will be discarded for packets with CRC errors. If this bit
is set, then the Timestamp will be made available in the normal manner.
9
TS_APPEND
0, RW
Append Timestamp for L2:
For Layer 2 encapsulated PTP messages, if this bit is set, always append the
Timestamp to end of the PTP message rather than inserted in unused message
fields. This bit will be ignored if TS_INSERT is 0.
8
TS_INSERT
0, RW
Enable Timestamp Insertion:
Enables Timestamp insertion into a packet containing a PTP Event Message. If
this bit is set, the Timestamp will not be available through the PTP Receive
Timestamp Register.
7:0
PTP_DOMAIN
0000 0000, RW
PTP Domain:
Value of the PTP Message domainNumber field. If PTP_RXCFG0:DOMAIN_EN
is set to 1, the Receive Timestamp unit will only capture a Timestamp if the
domainNumber in the receive PTP message matches the value in this field. If the
DOMAIN_EN bit is set to 0, the domainNumber field will be ignored.
www.national.com
96
DP83630
14.6.10 PTP Receive Configuration Register 4 (PTP_RXCFG4), Page 5
This register provides extended configuration for IEEE 1588 Receive Timestamp operation.
TABLE 72. PTP Receive Configuration Register 4 (PTP_RXCFG4), address 0x1D
Bit
Bit Name
Default
Description
15
IPV4_UDP_MOD
0, RW
Enable IPV4 UDP Modification:
When timestamp insertion is enabled, this bit controls how UDP checksums are
handled for IPV4 PTP event messages.
If set to a 0, the device will clear the UDP checksum. If a UDP checksum error is
detected the device will force a CRC error.
If set to a 1, the device will not clear the UDP checksum. Instead it will generate
a 2-byte value to correct the UDP checksum and append this immediately
following the PTP message. If an incoming UDP checksum error is detected, the
device will cause a UDP checksum error in the modified field. This function should
only be used if the incoming packets contain two extra bytes of UDP data following
the PTP message. This should not be enabled for systems using version 1 of the
IEEE 1588 specification.
14
TS_SEC_EN
0, RW
Enable Timestamp Seconds:
Setting this bit to a 1 enables inserting a seconds field when Timestamp Insertion
is enabled. If set to 0, only the nanoseconds portion of the Timestamp will be
inserted in the packet. This bit will be ignored if TS_INSERT is 0.
13:12
TS_SEC_LEN
00, RW
Inserted Timestamp Seconds Length:
This field indicates the length of the Seconds field to be inserted in the PTP
message. This field will be ignored if TS_INSERT is 0 or if TS_SEC_EN is 0. The
mapping is as follows:
00 : Least Significant Byte only of Seconds field
01 : Two Least Significant Bytes of Seconds field
10 : Three Least Significant Bytes of Seconds field
11 : All four Bytes of Seconds field
11:6
RXTS_NS_OFF
0000 00, RW
Receive Timestamp Nanoseconds offset:
This field provides an offset to the Nanoseconds field when inserting a Timestamp
into a received PTP message. If TS_APPEND is set to 1, the offset indicates an
offset from the end of the PTP message. If TS_APPEND is set to 0, the offset
indicates the byte offset from the beginning of the PTP message. This field will
be ignored if TS_INSERT is 0.
5:0
RXTS_SEC_OFF
00 0000, RW
Receive Timestamp Seconds offset:
This field provides an offset to the Seconds field when inserting a Timestamp into
a received PTP message. If TS_APPEND is set to 1, the offset indicates an offset
from the end of the inserted Nanoseconds field. If TS_APPEND is set to 0, the
offset indicates the byte offset from the beginning of the PTP message. This field
will be ignored if TS_INSERT is 0.
14.6.11 PTP Temporary Rate Duration Low Register (PTP_TRDL), Page 5
This register contains the low 16 bits of the duration in clock cycles to use the Temporary Rate as programmed in the PTP_RATEH
and PTP_RATEL registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL register, this register should be
programmed before setting the Temporary Rate. This register does not need to be reprogrammed for each use of the Temporary
Rate registers.
TABLE 73. PTP Temporary Rate Duration Low Register (PTP_TRDL), address 0x1E
Bit
Bit Name
Default
Description
15:0
PTP_TR_DURL
0000 0000 0000
0000, RW
PTP Temporary Rate Duration Low 16 bits:
This register sets the duration for the Temporary Rate in number of clock cycles.
The actual Time duration is dependent on the value of the Temporary Rate.
97
www.national.com
DP83630
14.6.12 PTP Temporary Rate Duration High Register (PTP_TRDH), Page 5
This register contains the high 10 bits of the duration in clock cycles to use the Temporary Rate as programmed in the PTP_RATEH
and PTP_RATEL registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL register, this register should be
programmed before setting the Temporary Rate. This register does not need to be reprogrammed for each use of the Temporary
Rate registers.
TABLE 74. PTP Temporary Rate Duration High Register (PTP_TRDH), address 0x1F
Bit
Bit Name
Default
15:10
RESERVED
0000 00, RO
9:0
PTP_TR_DURH
Description
Reserved: Writes ignored, Read as 0
00 0000 0000, RW PTP Temporary Rate Duration High 10 bits:
This register sets the duration for the Temporary Rate in number of clock cycles.
The actual Time duration is dependent on the value of the Temporary Rate.
14.7 PTP 1588 CONFIGURATION REGISTERS - PAGE 6
Page 6 PTP 1588 Configuration Registers are accessible by setting bits [2:0] = 110 of PAGESEL (13h).
14.7.1 PTP Clock Output Control Register (PTP_COC), Page 6
This register provides configuration for the PTP clock-synchronized output divide-by-N clock.
TABLE 75. PTP Clock Output Control Register (PTP_COC), address 0x14
Bit
Bit Name
Default
15
PTP_CLKOUT EN
1, RW
PTP Clock Output Enable:
1 = Enable PTP divide-by-N clock output.
0 = Disable PTP divide-by-N clock output.
14
PTP_CLKOUT SEL
0, RW
PTP Clock Output Source Select:
1 = Select the Phase Generation Module (PGM) as the root clock for generating
the divide-by-N output.
0 = Select the Frequency-Controlled Oscillator (FCO) as the root clock for
generating the divide-by-N output.
For additional information related to the PTP clock output selection, refer to
application note AN–1729.
13
PTP_CLKOUT
SPEEDSEL
0, RW
PTP Clock Output I/O Speed Select:
1 = Enable faster rise/fall time for the divide-by-N clock output pin.
0 = Enable normal rise/fall time for the divide-by-N clock output pin.
12:8
RESERVED
0 0000, RO
7:0
PTP_CLKDIV
0000 1010, RW
www.national.com
Description
Reserved: Writes ignored, Read as 0
PTP Clock Divide-by Value:
This field sets the divide-by value for the output clock. The output clock is divided
from an internal 250 MHz clock. Valid values range from 2 to 255 (0x02 to 0xFF),
giving a nominal output frequency range of 125 MHz down to 980.4 kHz. Divideby values of 0 and 1 are not valid and will stop the output clock.
98
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this register is used as the
first 16-bits of the PTP Header data for the PHY Status Frame.
TABLE 76. PHY Status Frame Configuration Register 1 (PSF_CFG1), address 0x15
Bit
Bit Name
Default
Description
15:12
PTPRESERVED
0000, RW
PTP v2 reserved field:
This field contains the reserved 4-bit field (at offset 1) to be sent in status packets
from the PHY to the local MAC using the MII receive data interface.
11:8
VERSIONPTP
0000, RW
PTP v2 versionPTP field:
This field contains the versionPTP field to be sent in status packets from the PHY
to the local MAC using the MII receive data interface.
7:4
TRANSPORTSPECIFIC
0000, RW
PTP v2 Header transportSpecific field:
This field contains the MESSAGETYPE field to be sent in status packets from the
PHY to the local MAC using the MII receive data interface.
3:0
MESSAGETYPE
0000, RW
PTP v2 messageType field:
This field contains the MESSAGETYPE field to be sent in status packets from the
PHY to the local MAC using the MII receive data interface.
14.7.3 PHY Status Frame Configuration Register 2 (PSF_CFG2), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this register is used as the
first 16-bits of the IP Source address for an IPv4 PHY Status Frame.
TABLE 77. PHY Status Frame Configuration Register 2 (PSF_CFG2), address 0x16
Bit
Bit Name
Default
15:8
IP_SA_BYTE1
0000 0000, RW
Second byte of IP source address:
This field contains the second byte of the IP source address.
Description
7:0
IP_SA_BYTE0
0000 0000, RW
First byte of IP source address:
This field contains the most significant byte of the IP source address.
14.7.4 PHY Status Frame Configuration Register 3 (PSF_CFG3), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this register is used as the
second 16-bits of the IP Source address for an IPv4 PHY Status Frame.
TABLE 78. PHY Status Frame Configuration Register 3 (PSF_CFG3), address 0x17
Bit
Bit Name
Default
Description
15:8
IP_SA_BYTE3
0000 0000, RW
Fourth byte of IP source address:
This field contains the fourth byte of the IP source address.
7:0
IP_SA_BYTE2
0000 0000, RW
Third byte of IP source address:
This field contains the third byte of the IP source address.
14.7.5 PHY Status Frame Configuration Register 4 (PSF_CFG4), Page 6
This register provides configuration for the PHY Status Frame function. Specifically, the 16-bit value in this register is used to assist
in computation of the IP checksum for an IPv4 PHY Status Frame.
TABLE 79. PHY Status Frame Configuration Register 4 (PTP_PKTSTS4), address 0x18
Bit
Bit Name
Default
Description
15:0
IP_CHKSUM
0000 0000 0000
0000, RW
IP Checksum:
This field contains a precomputed value ones-complement addition of all fixed
values in the IP Header. The device will add the Total Length and Identification
values to generate the final checksum.
99
www.national.com
DP83630
14.7.2 PHY Status Frame Configuration Register 1 (PSF_CFG1), Page 6
DP83630
14.7.6 PTP SFD Configuration Register (PTP_SFDCFG), Page 6
This register provides configuration to enable outputting the RX and TX Start-of-Frame (SFD) signals on GPIO pins. Note that
GPIO assignments are not exclusive.
TABLE 80. PTP SFD Configuration Register (PTP_SFDCFG), address 0x19
Bit
Bit Name
Default
15:8
RESERVED
0000 0000, RO
Description
7:4
TX_SFD_GPIO
0000, RW
TX SFD GPIO Select:
This field controls the GPIO output to which the TX SFD signal is assigned. Valid
values are 0 (disabled) or 1-12.
3:0
RX_SFD_GPIO
0000, RW
RX SFD GPIO Select:
This field controls the GPIO output to which the RX SFD signal is assigned. Valid
values are 0 (disabled) or 1-12.
Reserved: Writes ignored, Read as 0
14.7.7 PTP Interrupt Control Register (PTP_INTCTL), Page 6
This register provides configuration for the IEEE 1588 interrupt function, allowing the PTP Interrupt to use any of the GPIO pins.
TABLE 81. PTP Interrupt Control Register (PTP_INTCTL), address 0x1A
Bit
Bit Name
Default
15:4
RESERVED
0000 0000 0000,
RO
3:0
PTP_INT_GPIO
0000, RW
Description
Reserved: Writes ignored, Read as 0
PTP Interrupt GPIO Select:
To enable interrupts on a GPIO pin, this field should be set to the GPIO number.
Setting this field to 0 will disable interrupts via the GPIO pins.
14.7.8 PTP Clock Source Register (PTP_CLKSRC), Page 6
This register provides configuration for the reference clock source driving the IEEE 1588 logic. The source clock period is also
used by the 1588 clock nanoseconds adder to add the proper value every reference clock cycle.
TABLE 82. PTP Clock Source Register (PTP_CLKSRC), address 0x1B
Bit
Bit Name
Default
15:14
CLK_SRC
00, RW
Description
13:7
RESERVED
00 0000 0, RO
Reserved: Writes ignored, Read as 0
6:0
CLK_SRC_PER
000 0000, RW
PTP Clock Source Period:
This field configures the PTP clock source period in nanoseconds. Values less
than 8 are invalid and cannot be written; attempting to write a value less than 8
will cause CLK_SRC_PER to be 8. When the clock source selection is the Divideby-N from the internal PGM, bits 6:3 are used as the N value; bits 2:0 are ignored
in this mode.
PTP Clock Source Select:
Selects among three possible sources for the PTP reference clock:
00 : 125 MHz from internal PGM (default)
01 : Divide-by-N from 125 MHz internal PGM
1x : External reference clock
14.7.9 PTP Ethernet Type Register (PTP_ETR), Page 6
This register provides the Ethernet Type (Ethertype) field for PTP transport over Ethernet (Layer2).
TABLE 83. PTP Ethernet Type Register (PTP_ETR), address 0x1C
Bit
Bit Name
Default
15:0
PTP_ETYPE
1111 0111 1000
1000, RW
www.national.com
Description
PTP Ethernet Type:
This field contains the Ethernet Type field used to detect PTP messages
transported over Ethernet layer 2.
100
DP83630
14.7.10 PTP Offset Register (PTP_OFF), Page 6
This register provides the byte offset to the PTP message in a Layer2 Ethernet frame.
TABLE 84. PTP Offset Register (PTP_OFF), address 0x1D
Bit
Bit Name
Default
Description
15:8
RESERVED
0000 0000, RO
Reserved: Writes ignored, Read as 0
7:0
PTP_OFFSET
0000 0000, RO
PTP Offset:
This field contains the offset in bytes to the PTP Message from the preceding
header. For Layer2, this is the offset from the Ethernet Type Field. For UDP/IP, it
is the offset from the end of the UDP Header.
14.7.11 PTP GPIO Monitor Register (PTP_GPIOMON), Page 6
This register provides read-only access to the current values on GPIO inputs.
TABLE 85. PTP GPIO Monitor Register (PTP_GPIOMON), address 0x1E
Bit
Bit Name
Default
15:12
RESERVED
0000, RO
11:0
PTP_GPIO_IN
0000 0000 0000,
RO
Description
Reserved: Writes ignored, Read as 0
PTP GPIO Inputs:
This field reflects the current values seen on the GPIO inputs. GPIOs 12 through
1 are mapped to bits 11:0 in order.
14.7.12 PTP Receive Hash Register (PTP_RXHASH), Page 6
This register provides configuration for the source identity hash filter of the PTP receive packet parser. If enabled, the receive parse
logic will deliver a receive timestamp only if the hash function on the ten octet sourcePortIdentity field correctly matches the
programmed value. The source identity hash filter does not affect timestamp insertion.
TABLE 86. PTP Receive Hash Register (PTP_RXHASH), address 0x1F
Bit
Bit Name
Default
15:13
RESERVED
000, RO
12
RX_HASH_EN
0, RW
11:0
PTP_RX_HASH
0000 0000 0000,
RW
Description
Reserved: Writes ignored, Read as 0
Receive Hash Enable:
Enables filtering of PTP messages based on the hash function on the ten octet
sourcePortIdentity field.
Receive Hash:
This field contains the expected source identity hash value for incoming PTP
event messages.
101
www.national.com
DP83630
15.0 Absolute Maximum Ratings (Note
16.0 Recommended Operating
Conditions
4)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (VCC)
DC Input Voltage (VIN)
DC Output Voltage (VOUT)
Storage Temperature (TSTG )
Maximum Case
Temperature for TA = 85 °C
Maximum Die Temperature
(Tj)
ESD Rating
(RZAP = 1.5k, CZAP = 120 pF)
Analog Supply Voltage (VCC)
I/O Supply Voltage (VI/O)
3.3 Volts ± 0.3V
3.3 Volts ± 10%
or
2.5 Volts ± 5%
Industrial Temperature (TI)
-40 to 85 °C
Power Dissipation (PD) with VI/O = 3.3 V
290 mW
Power Dissipation (PD) with VI/O = 2.5 V
260 mW
-0.5 V to 4.2 V
-0.5V to VCC + 0.5V
-0.5V to VCC + 0.5V
-65°C to 150°C
95 °C
17.0 Thermal Characteristic
150 °C
Theta Junction to Case (Tjc)
Theta Junction to Ambient (Tja)
degrees Celsius/Watt - No Airflow
@ 1.0 W
8.0 kV
For soldering specifications: see product folder at
www.national.com
and
www.national.com/ms/MS/MSSOLDERING.pdf
Max
TBD
TBD
Units
°C / W
°C / W
Note 4: Absolute maximum ratings are those values beyond which the
safety of the device cannot be guaranteed. They are not meant to imply that
the device should be operated at these limits.
18.0 AC and DC Specifications
18.1 DC SPECIFICATIONS
Pin
Types
Symbol
Parameter
VIH
I
I/O
Input High Voltage
VIL
I
I/O
Input Low Voltage
IIH
I
I/O
IIL
Conditions
Min
Typ
Max
2.0
Units
V
VI/O = 3.3 V
0.8
V
VI/O = 2.5 V
0.7
V
Input High Current
VIN = VI/O
10
µA
I
I/O
Input Low Current
VIN = GND
10
µA
VOL
O
I/O
Output Low Voltage
IOL = 4 mA
0.4
V
VOH
O
I/O
Output High Voltage
IOH = -4 mA
IOZ
O
I/O
TRI-STATE Output Leakage
Current
VOUT = VI/O or GND
VI/O - 0.5
V
-10
1.05
V
±2
%
PMD
100M Transmit Voltage
Output Pair
VTPTDsym
PMD
100M Transmit Voltage
Output Pair Symmetry
VTPTD_10
PMD
10M Transmit Voltage
Output Pair
2.2
2.5
2.8
V
VFXTD_100
PMD
FX 100M Transmit Voltage
Output Pair
0.3
0.5
0.93
V
COUT1
I
CMOS Input Capacitance
8
O
CMOS Output Capacitance
8
SDTHon
PMD Input 100BASE-TX Signal detect
Pair
turn-on threshold
SDTHoff
PMD Input Signal detect turn-off threshold
Pair
www.national.com
1
µA
VTPTD_100
CIN1
0.95
10
pF
pF
1000
200
102
mV diff pk-pk
mV diff pk-pk
VTH
Idd100
Idd10
Idd
Pin
Types
Parameter
Conditions
PMD Input 10BASE-T Receive Threshold
Pair
Supply
Supply
Supply
100BASE-TX (Full Duplex)
10BASE-T (Full Duplex)
Power Down Mode
Min
Typ
300
Max
Units
585
mV
VCC = 3.3 V, VI/O = 3.3 V,
IOUT = 0 mA (Note 5)
88
mA
VCC = 3.3 V, VI/O = 2.5 V,
IOUT = 0 mA (Note 5)
84
mA
VCC = 3.3 V, VI/O = 3.3 V,
IOUT = 0 mA (Note 5)
105
mA
VCC = 3.3 V, VI/O = 2.5 V,
IOUT = 0 mA (Note 5)
103
mA
CLK_OUT disabled
10
mA
Note 5: For Idd measurements, outputs are not loaded
103
www.national.com
DP83630
Symbol
DP83630
18.2 AC SPECIFICATIONS
18.2.1 Power Up Timing
30136220
Notes
Min
T2.1.1
Parameter
Post Power Up Stabilization time
prior to MDC preamble for register
accesses
Description
MDIO is pulled high for 32-bit serial
management initialization.
167
Typ
ms
T2.1.2
Hardware Configuration Latch-in
Time from power up
Hardware Configuration Pins are
described in the Pin Description
section.
167
ms
T2.1.3
Hardware Configuration pins
transition to output drivers
50
Note: In RMII Slave Mode, the minimum Post Power up Stabilization and Hardware Configuration Latch-in times are 84 ms.
www.national.com
104
Max
Units
ns
DP83630
18.2.2 Reset Timing
30136221
Parameter
Description
Notes
Min
Typ
Max
Units
T2.2.1
Post RESET Stabilization time prior to MDIO is pulled high for 32-bit serial
MDC preamble for register accesses management initialization
3
µs
T2.2.2
Hardware Configuration Latch-in Time Hardware Configuration Pins are
from the Deassertion of RESET (either described in the Pin Description
soft or hard)
section
3
µs
T2.2.3
Hardware Configuration pins transition
to output drivers
50
ns
T2.2.4
RESET pulse width
X1 Clock must be stable for at min.
of 1 µs during RESET pulse low
time.
1
µs
Note: It is important to choose pull-up and/or pull-down resistors for each of the hardware configuration pins that provide fast RC time constants in order to latchin the proper value prior to the pin transitioning to an output driver.
105
www.national.com
DP83630
18.2.3 MII Serial Management Timing
30136222
Parameter
Description
Notes
Min
Typ
Max
Units
20
ns
T2.3.1
MDC to MDIO (Output) Delay Time
0
T2.3.2
MDIO (Input) to MDC Setup Time
10
ns
T2.3.3
MDIO (Input) to MDC Hold Time
10
ns
T2.3.4
MDC Frequency
2.5
25
MHz
18.2.4 100 Mb/s MII Transmit Timing
30136223
Parameter
Description
Notes
Min
Typ
Max
Units
20
24
ns
T2.4.1
TX_CLK High/Low Time
100 Mb/s Normal mode
16
T2.4.2
TXD[3:0], TX_EN Data Setup to
TX_CLK
100 Mb/s Normal mode
10
ns
T2.4.3
TXD[3:0], TX_EN Data Hold from
TX_CLK
100 Mb/s Normal mode
0
ns
www.national.com
106
DP83630
18.2.5 100 Mb/s MII Receive Timing
30136224
Min
Typ
Max
Units
T2.5.1
Parameter
RX_CLK High/Low Time
Description
100 Mb/s Normal mode
Notes
16
20
24
ns
T2.5.2
RX_CLK to RXD[3:0], RX_DV, RX_ER 100 Mb/s Normal mode
Delay
10
30
ns
Note: RX_CLK may be held low or high for a longer period of time during transition between reference and recovered clocks. Minimum high and low times will
not be violated.
18.2.6 100BASE-TX and 100BASE-FX MII Transmit Packet Latency Timing
30136225
Parameter
T2.6.1
Description
TX_CLK to PMD Output Pair Latency
Notes
100BASE-TX and 100BASE-FX modes
IEEE 1588 One-Step Operation enabled
Min
Typ
5
9
Max
Units
bits
bits
Note: For Normal mode, latency is determined by measuring the time from the first rising edge of TX_CLK occurring after the assertion of TX_EN to the first bit
of the “J” code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100 Mb/s mode.
Note: Enabling PHY Control Frames will add latency equal to 8 bits times the PCF_BUF_SIZE setting. For example if PCF_BUF_SIZE is set to 15, then the
additional delay will be 15*8 = 120 bits.
107
www.national.com
DP83630
18.2.7 100BASE-TX and 100BASE-FX MII Transmit Packet Deassertion Timing
30136226
Parameter
T2.7.1
Description
Notes
Min
TX_CLK to PMD Output Pair Deassertion 100BASE-TX and 100BASE-FX modes
Typ
Max
5
Units
bits
Note: Deassertion is determined by measuring the time from the first rising edge of TX_CLK occurring after the deassertion of TX_EN to the first bit of the “T”
code group as output from the PMD Output Pair. 1 bit time = 10 ns in 100 Mb/s mode.
18.2.8 100BASE-TX Transmit Timing (tR/F & Jitter)
30136227
Parameter
T2.8.1
T2.8.2
Description
Notes
Min
Typ
Max
Units
3
4
5
ns
100 Mb/s tR and tF Mismatch
500
ps
100 Mb/s PMD Output Pair Transmit Jitter
1.4
ns
100 Mb/s PMD Output Pair tR and tF
Note: Normal Mismatch is the difference between the maximum and minimum of all rise and fall times
Note: Rise and fall times taken at 10% and 90% of the +1 or -1 amplitude
www.national.com
108
DP83630
18.2.9 100BASE-TX and 100BASE-FX MII Receive Packet Latency Timing
30136228
Description
Notes
T2.9.1
Parameter
Carrier Sense ON Delay
100BASE-TX mode
100BASE-FX mode
Min
Typ
20
10
Max
Units
bits
T2.9.2
Receive Data Latency
100BASE-TX mode
100BASE-FX mode
24
14
bits
Note: Carrier Sense On Delay is determined by measuring the time from the first bit of the “J” code group to the assertion of Carrier Sense.
Note: 1 bit time = 10 ns in 100 Mb/s mode.
Note: Enabling IEEE 1588 Receive Timestamp insertion will increase the Receive Data Latency by 40 bit times.
Note: Enabling PHY Status Frames will introduce variability in Receive Data Latency due to insertion of PHY Status Frames into the receive datapath.
18.2.10 100BASE-TX and 100BASE-FX MII Receive Packet Deassertion Timing
30136229
Parameter
T2.10.1
Description
Carrier Sense OFF Delay
Notes
100BASE-TX mode
100BASE-FX mode
Min
Typ
Max
24
14
Units
bits
Note: Carrier Sense Off Delay is determined by measuring the time from the first bit of the “T” code group to the deassertion of Carrier Sense.
Note: 1 bit time = 10 ns in 100 Mb/s mode.
109
www.national.com
DP83630
18.2.11 10 Mb/s MII Transmit Timing
30136230
Parameter
Description
Notes
Min
Typ
Max
Units
200
210
ns
T2.11.1
TX_CLK High/Low Time
10 Mb/s MII mode
190
T2.11.2
TXD[3:0], TX_EN Data Setup to
TX_CLK falling edge
10 Mb/s MII mode
25
ns
T2.11.3
TXD[3:0], TX_EN Data Hold from
TX_CLK rising edge
10 Mb/s MII mode
0
ns
Note: An attached Mac should drive the transmit signals using the positive edge of TX_CLK. As shown above, the MII signals are sampled on the falling edge
of TX_CLK.
18.2.12 10 Mb/s MII Receive Timing
30136231
Parameter
Description
Notes
Min
Typ
Max
Units
160
200
240
ns
T2.12.1
RX_CLK High/Low Time
T2.12.2
RXD[3:0], RX_DV transition delay
from RX_CLK rising edge
10 Mb/s MII mode
100
ns
T2.12.3
RX_CLK rising edge delay from RXD 10 Mb/s MII mode
[3:0], RX_DV valid data
100
ns
Note: RX_CLK may be held low for a longer period of time during transition between reference and recovered clocks. Minimum high and low times will not be
violated.
www.national.com
110
DP83630
18.2.13 10BASE-T MII Transmit Timing (Start of Packet)
30136234
Parameter
T2.13.1
Description
Transmit Output Delay from the
Falling Edge of TX_CLK
Notes
Min
10 Mb/s MII mode
Typ
Max
3.5
Units
bits
Note: 1 bit time = 100 ns in 10 Mb/s.
18.2.14 10BASE-T MII Transmit Timing (End of Packet)
30136235
Min
Typ
T2.14.1
Parameter
End of Packet High Time
(with '0' ending bit)
Description
Notes
250
300
ns
T2.14.2
End of Packet High Time
(with '1' ending bit)
250
300
ns
111
Max
Units
www.national.com
DP83630
18.2.15 10BASE-T MII Receive Timing (Start of Packet)
30136236
Parameter
Description
T2.15.1
Carrier Sense Turn On Delay (PMD
Input Pair to CRS)
T2.15.2
RX_DV Latency
T2.15.3
Receive Data Latency
Notes
Min
Typ
Max
Units
630
1000
ns
Measurement shown from SFD
10
bits
8
bits
Note: 10BASE-T RX_DV Latency is measured from first bit of preamble on the wire to the assertion of RX_DV
Note: 1 bit time = 100 ns in 10 Mb/s mode.
18.2.16 10BASE-T MII Receive Timing (End of Packet)
30136237
Parameter
T2.16.1
Description
Notes
Carrier Sense Turn Off Delay
www.national.com
112
Min
Typ
Max
Units
1.0
µs
DP83630
18.2.17 10 Mb/s Heartbeat Timing
30136238
Parameter
Description
Notes
Min
Typ
Max
Units
T2.17.1
CD Heartbeat Delay
All 10 Mb/s modes
1200
ns
T2.17.2
CD Heartbeat Duration
All 10 Mb/s modes
1000
ns
18.2.18 10 Mb/s Jabber Timing
30136239
Parameter
Description
Notes
Min
Typ
Max
Units
T2.18.1
Jabber Activation Time
85
ms
T2.18.2
Jabber Deactivation Time
500
ms
113
www.national.com
DP83630
18.2.19 10BASE-T Normal Link Pulse Timing
30136240
Parameter
Description
Notes
Min
Typ
Max
Units
T2.19.1
Pulse Width
100
ns
T2.19.2
Pulse Period
16
ms
Note: These specifications represent transmit timings.
18.2.20 Auto-Negotiation Fast Link Pulse (FLP) Timing
30136241
Parameter
Description
Notes
Min
Typ
Max
Units
T2.20.1
Clock, Data Pulse Width
100
ns
T2.20.2
Clock Pulse to Clock Pulse
Period
125
µs
T2.20.3
Clock Pulse to Data Pulse
Period
62
µs
T2.20.4
Burst Width
2
ms
T2.20.5
FLP Burst to FLP Burst Period
16
ms
Data = 1
Note: These specifications represent transmit timings.
www.national.com
114
DP83630
18.2.21 100BASE-TX Signal Detect Timing
30136242
Parameter
Description
T2.21.1
SD Internal Turn-on Time
T2.21.2
SD Internal Turn-off Time
Notes
Min
Default operation
Fast link-loss indication
enabled
Typ
250
1.3
Max
Units
1
ms
300
µs
µs
Note: The signal amplitude on PMD Input Pair must be TP-PMD compliant.
Note: Fast Link-loss detect is enabled by setting the SD_CNFG[8] register bit to a 1.
18.2.22 100 Mb/s Internal Loopback Timing
30136243
Parameter
T2.22.1
Description
TX_EN to RX_DV Loopback
Notes
100 Mb/s internal loopback mode
Min
Typ
Max
Units
240
ns
Note: Due to the nature of the descrambler function, all 100BASE-TX Loopback modes will cause an initial “dead-time” of up to 550 µs during which time no data
will be present at the receive MII outputs. The 100BASE-TX timing specified is based on device delays after the initial 550µs “dead-time”.
Note: Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
115
www.national.com
DP83630
18.2.23 10 Mb/s Internal Loopback Timing
30136244
Parameter
Description
T2.23.1
TX_EN to RX_DV Loopback
Notes
Min
Typ
10 Mb/s internal loopback mode
Max
Units
2
µs
Note: Measurement is made from the first falling edge of TX_CLK after assertion of TX_EN.
18.2.24 RMII Transmit Timing (Slave Mode)
30136245
Parameter
Description
Notes
Min
50 MHz Reference Clock
Typ
Units
T2.24.1
X1 Clock Period
T2.24.2
TXD[1:0], TX_EN, Data Setup to X1 rising edge
4
ns
T2.24.3
TXD[1:0], TX_EN, Data Hold from X1 rising edge
2
ns
T2.24.4
X1 Clock to PMD Output Pair Latency (100 Mb) 100BASE-TX or 100BASE-FX
Note: Latency measurement is made from the X1 rising edge to the first bit of symbol.
www.national.com
116
20
Max
11
ns
bits
DP83630
18.2.25 RMII Transmit Timing (Master Mode)
30136254
Parameter
Description
Notes
Min
50 MHz Reference Clock
Typ
Units
RX_CLK, TX_CLK, CLK_OUT Period
T2.25.2
TXD[1:0], TX_EN Data Setup to RX_CLK,
TX_CLK, CLK_OUT rising edge
4
ns
T2.25.3
TXD[1:0], TX_EN Data Hold from RX_CLK,
TX_CLK, CLK_OUT rising edge
2
ns
T2.25.4
RX_CLK, TX_CLK, CLK_OUT to PMD Output
Pair Latency
From RX_CLK rising edge to
first bit of symbol
20
Max
T2.25.1
11
ns
bits
Note: Latency measurement is made from the RX_CLK rising edge to the first bit of symbol.
117
www.national.com
DP83630
18.2.26 RMII Receive Timing (Slave Mode)
30136255
Parameter
Description
Notes
Min
50 MHz Reference Clock
Typ
Max
20
Units
T2.26.1
X1 Clock Period
T2.26.2
RXD[1:0], CRS_DV, and RX_ER
output delay from X1 rising edge
T2.26.3
CRS ON delay
100BASE-TX mode
100BASE-FX mode
18.5
9
bits
T2.26.4
CRS OFF delay
100BASE-TX mode
100BASE-FX mode
27
17
bits
T2.26.5
RXD[1:0] and RX_ER latency
100BASE-TX mode
100BASE-FX mode
38
27
bits
2
ns
14
ns
Note: Per the RMII Specification, output delays assume a 25 pF load.
Note: CRS_DV is asserted asynchronously in order to minimize latency of control signals through the PHY. CRS_DV may toggle synchronously at the end of
the packet to indicate CRS de-assertion.
Note: CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to initial assertion of CRS_DV.
Note: CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to initial de-assertion of CRS_DV.
Note: Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set to the default value
(01).
Note: Enabling IEEE 1588 Receive Timestamp insertion will increase the Receive Data Latency by 40 bit times.
Note: Enabling PHY Status Frames will introduce variability in Receive Data Latency due to insertion of PHY Status Frames into the receive datapath.
www.national.com
118
DP83630
18.2.27 RMII Receive Timing (Master Mode)
30136246
Parameter
Description
Notes
Min
50 MHz Reference Clock
Typ
Max
20
Units
T2.27.1
RX_CLK, TX_CLK, CLK_OUT
Clock Period
T2.27.2
RXD[1:0], CRS_DV, RX_DV and
RX_ER output delay from
RX_CLK, TX_CLK, CLK_OUT
rising edge
T2.27.3
CRS ON delay
100BASE-TX mode
100BASE-FX mode
18.5
9
bits
T2.27.4
CRS OFF delay
100BASE-TX mode
100BASE-FX mode
27
17
bits
T2.27.5
RXD[1:0] and RX_ER latency
100BASE-TX mode
100BASE-FX mode
38
27
bits
2
ns
14
ns
Note: Per the RMII Specification, output delays assume a 25 pF load.
Note: CRS_DV is asserted asynchronously in order to minimize latency of control signals through the PHY. CRS_DV may toggle synchronously at the end of
the packet to indicate CRS de-assertion.
Note: CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to initial assertion of CRS_DV.
Note: CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to initial de-assertion of CRS_DV.
Note: Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set to the default value
(01).
119
www.national.com
DP83630
18.2.28 RX_CLK Timing (RMII Master Mode)
30136256
Parameter
Description
Notes
Min
Typ
Max
Units
T2.28.1
RX_CLK High Time
12
ns
T2.28.2
RX_CLK Low Time
8
ns
T2.28.3
RX_CLK Period
20
ns
Note: The High Time and Low Time will add up to 20 ns.
18.2.29 CLK_OUT Timing (RMII Slave Mode)
30136257
Parameter
Description
T2.29.1
CLK_OUT High/Low Time
T2.29.2
CLK_OUT propagation delay
www.national.com
Notes
Min
Typ
Max
10
Relative to X1
ns
8
120
Units
ns
DP83630
18.2.30 Single Clock MII (SCMII) Transmit Timing
30136247
Parameter
Description
Notes
Min
T2.30.1
X1 Clock Period
25 MHz Reference Clock
T2.30.2
TXD[3:0], TX_EN Data Setup
To X1 rising edge
4
T2.30.3
TXD[3:0], TX_EN Data Hold
From X1 rising edge
2
T2.30.4
X1 Clock to PMD Output Pair
Latency (100 Mb)
100BASE-TX or 100BASE-FX
Typ
40
Max
Units
ns
ns
ns
13
bits
Note: Latency measurement is made from the X1 rising edge to the first bit of symbol.
121
www.national.com
DP83630
18.2.31 Single Clock MII (SCMII) Receive Timing
30136248
Parameter
Description
Notes
Min
25 MHz Reference Clock
Typ
Max
40
Units
T2.31.1
X1 Clock Period
T2.31.2
RXD[3:0], RX_DV and RX_ER output delay From X1 rising edge
T2.31.3
CRS ON delay
100BASE-TX mode
100BASE-FX mode
19
9
bits
T2.31.4
CRS OFF delay
100BASE-TX mode
100BASE-FX mode
26
16
bits
T2.31.5
RXD[3:0] and RX_ER latency
100BASE-TX mode
100BASE-FX mode
56
46
bits
2
ns
18
ns
Note: Output delays assume a 25 pF load.
Note: CRS is asserted and de-asserted asynchronously relative to the reference clock.
Note: CRS ON delay is measured from the first bit of the JK symbol on the PMD Input Pair to assertion of CRS_DV.
Note: CRS OFF delay is measured from the first bit of the TR symbol on the PMD Input Pair to de-assertion of CRS_DV.
Note: Receive Latency is measured from the first bit of the symbol pair on the PMD Input Pair. Typical values are with the Elasticity Buffer set to the default value
(01).
www.national.com
122
DP83630
18.2.32 100 Mb/s X1 to TX_CLK Timing
30136258
Parameter
T2.32.1
Description
X1 to TX_CLK delay
Notes
100 Mb/s Normal mode
Min
Typ
0
Max
Units
5
ns
Note: X1 to TX_CLK timing is provided to support devices that use X1 instead of TX_CLK as the reference for transmit MII data.
123
www.national.com
DP83630
19.0 Physical Dimensions inches (millimeters) unless otherwise noted
48-Lead LLP Plastic Quad Package, LLP
NS Package Number SQA48A
20.0 Ordering Information
www.national.com
Order Number
Package Marking
Supplied As
DP83630SQ
DP83630SQ
Reel of 1000
DP83630SQE
DP83630SQ
Reel of 250
DP83630SQX
DP83630SQ
Reel of 2500
124
DP83630
125
www.national.com
DP83630 Precision PHYTER - IEEE 1588 Precision Time Protocol Transceiver
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages