TI1 DP83815DVNG 10/100 mb/s integrated pci ethernet media access controller and physical layer (macphyter) Datasheet

DP83815
DP83815 10/100 Mb/s Integrated PCI Ethernet Media Access Controller and
Physical Layer (MacPhyter)
Literature Number: SNLS059E
DP83815
10/100 Mb/s Integrated PCI Ethernet Media Access
Controller and Physical Layer (MacPhyter™)
DP83815 is a single-chip 10/100 Mb/s Ethernet Controller
for the PCI bus. It is targeted at low-cost, high volume PC
mother boards, adapter cards, and embedded systems.
The DP83815 fully implements the V2.2 33 MHz PCI bus
interface for host communications with power management
support. Packet descriptors and data are transferred via
bus-mastering, reducing the burden on the host CPU. The
DP83815 can support full duplex 10/100 Mb/s transmission
and reception, with minimum interframe gap.
Features
ol
e
The DP83815 device is an integration of an enhanced
version of the National Semiconductor PCI MAC/BIU
(Media Access Controller/Bus Interface Unit) and a 3.3V
CMOS physical layer interface.
— Virtual LAN (VLAN) and long frame support
— Support for IEEE 802.3x Full duplex flow control
— Extremely flexible Rx packet filtration including: single
address perfect filter with MSb masking, broadcast, 512
entry multicast/unicast hash table, deep packet pattern
matching for up to 4 unique patterns
— Statistics gathered for support of RFC 1213 (MIB II),
RFC 1398 (Ether-like MIB), IEEE 802.3 LME, reducing
CPU overhead for management
— Internal 2 KB Transmit and 2 KB Receive data FIFOs
— Serial EEPROM port with auto-load of configuration data
from EEPROM at power-on
— Flash/PROM interface for remote boot support
— Fully integrated IEEE 802.3/802.3u 3.3V CMOS physical
layer
— IEEE 802.3 10BASE-T transceiver with integrated filters
— IEEE 802.3u 100BASE-TX transceiver
— Fully integrated ANSI X3.263 compliant TP-PMD
physical sublayer with adaptive equalization and
Baseline Wander compensation
— IEEE 802.3u Auto-Negotiation - advertised features
configurable via EEPROM
— Full Duplex support for 10 and 100 Mb/s data rates
— Single 25 MHz reference clock
— 144-pin LQFP and 160-pin LBGA packages
— Low power 3.3V CMOS design with typical consumption
of 561 mW operating, 380 mW during WOL mode, 33
mW sleep mode
— IEEE 802.3u MII for connecting alternative external
Physical Layer Devices
te
General Description
O
bs
— IEEE 802.3 Compliant, PCI V2.2 MAC/BIU supports
traditional data rates of 10 Mb/s Ethernet and 100 Mb/s
Fast Ethernet (via internal phy)
— Bus master - burst sizes of up to 128 dwords (512 bytes)
— BIU compliant with PC 97 and PC 98 Hardware Design
Guides, PC 99 Hardware Design Guide draft, ACPI v1.0,
PCI Power Management Specification v1.1, OnNow
Device Class Power Management Reference
Specification - Network Device Class v1.0a
— Wake on LAN (WOL) support compliant with PC98,
PC99, SecureOn, and OnNow, including directed
packets, Magic Packet, VLAN packets, ARP packets,
pattern match packets, and Phy status change
— Clkrun function for PCI Mobile Design Guide
System Diagram
PCI Bus
10/100 Twisted Pair
DP83815
Isolation
BIOS ROM EEPROM
(optional) (optional)
Magic Packet is a trademark of Advanced Micro Devices, Inc.
© 2005 National Semiconductor Corporation
www.national.com
DP83815 10/100 Mb/s Integrated PCI Ethernet Media Access Controller and Physical Layer (MacPhyter™)
September 2005
3.12.2 MII Serial Management . . . . . . . . . . . . . . . . . . . . 29
1.0 Connection Diagram . . . . . . . . . . . . . . . . . . 4
3.12.3 MII Serial Management Access . . . . . . . . . . . . . 30
1.1 144 LQFP Package (VNG) . . . . . . . . . . . . 4
3.12.4 Serial Management Access Protocol . . . . . . . . . 30
1.2 160 pin LBGA Package (UJB) . . . . . . . . . . 5
3.12.5 Nibble-wide MII Data Interface . . . . . . . . . . . . . . 30
2.0 Pin Description . . . . . . . . . . . . . . . . . . . . . . 6
3.12.6 Collision Detection . . . . . . . . . . . . . . . . . . . . . . . 31
3.0 Functional Description . . . . . . . . . . . . . . . 13
3.12.7 Carrier Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.1 MAC/BIU . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.0 Register Set . . . . . . . . . . . . . . . . . . . . . . . . 32
3.1.1 PCI Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Configuration Registers . . . . . . . . . . . . . . 32
3.1.2 Tx MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.3 Rx MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Buffer Management . . . . . . . . . . . . . . . . . 15
3.2.1
3.2.2
3.2.3
3.2.4
Interface Definitions . . . . . . . . . . . . . . . . . 16
3.3.1
3.3.2
3.3.3
3.3.4
3.4
Physical Layer . . . . . . . . . . . . . . . . . . . . . 18
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.5
3.6
3.7
3.8
3.9
PCI System Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Boot PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Auto-Negotiation Register Control . . . . . . . . . . . . . 18
Auto-Negotiation Parallel Detection . . . . . . . . . . . . 18
Auto-Negotiation Restart . . . . . . . . . . . . . . . . . . . . 19
Enabling Auto-Negotiation via Software . . . . . . . . 19
Auto-Negotiation Complete Time . . . . . . . . . . . . . . 19
LED Interfaces . . . . . . . . . . . . . . . . . . . . .
Half Duplex vs. Full Duplex . . . . . . . . . . .
Phy Loopback . . . . . . . . . . . . . . . . . . . . .
Status Information . . . . . . . . . . . . . . . . . .
100BASE-TX TRANSMITTER . . . . . . . . .
4.2
19
20
20
20
20
Code-group Encoding and Injection . . . . . . . . . . . 21
Scrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
NRZ to NRZI Encoder . . . . . . . . . . . . . . . . . . . . . . 22
Binary to MLT-3 Convertor / Common Driver . . . . 22
bs
3.9.1
3.9.2
3.9.3
3.9.4
te
3.3
Tx Buffer Manager . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rx Buffer Manager . . . . . . . . . . . . . . . . . . . . . . . . . 15
Packet Recognition . . . . . . . . . . . . . . . . . . . . . . . . 15
MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.10 100BASE-TX Receiver . . . . . . . . . . . . . . 23
O
3.10.1 Input and Base Line Wander Compensation . . . . 23
3.10.2 Signal Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.10.3 Digital Adaptive Equalization . . . . . . . . . . . . . . . . 25
3.10.4 Line Quality Monitor . . . . . . . . . . . . . . . . . . . . . . . 26
3.10.5 MLT-3 to NRZI Decoder . . . . . . . . . . . . . . . . . . . . 26
3.10.6 Clock Recovery Module . . . . . . . . . . . . . . . . . . . . 27
3.10.7 NRZI to NRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.8 Serial to Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.9 De-scrambler . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.10 Code-group Alignment . . . . . . . . . . . . . . . . . . . . 27
3.10.11 4B/5B Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.12 100BASE-TX Link Integrity Monitor . . . . . . . . . . 27
3.10.13 Bad SSD Detection . . . . . . . . . . . . . . . . . . . . . . 27
3.11 10BASE-T Transceiver Module . . . . . . . . 28
3.11.1 Operational Modes . . . . . . . . . . . . . . . . . . . . . . . . 28
3.11.2 Smart Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.11.3 Collision Detection . . . . . . . . . . . . . . . . . . . . . . . . 28
3.11.4 Normal Link Pulse Detection/Generation . . . . . . . 28
3.11.5 Jabber Function . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.11.6 Automatic Link Polarity Detection . . . . . . . . . . . . . 29
3.11.7 10BASE-T Internal Loopback . . . . . . . . . . . . . . . . 29
3.11.8 Transmit and Receive Filtering . . . . . . . . . . . . . . . 29
3.11.9 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.11.10 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.11.11 Far End Fault Indication . . . . . . . . . . . . . . . . . . . 29
4.3
32
33
34
35
35
36
36
37
37
38
38
39
Operational Registers . . . . . . . . . . . . . . . 40
4.2.1 Command Register . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Configuration and Media Status Register . . . . . . .
4.2.3 EEPROM Access Register . . . . . . . . . . . . . . . . . .
4.2.4 EEPROM Map . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5 PCI Test Control Register . . . . . . . . . . . . . . . . . . .
4.2.6 Interrupt Status Register . . . . . . . . . . . . . . . . . . . .
4.2.7 Interrupt Mask Register . . . . . . . . . . . . . . . . . . . .
4.2.8 Interrupt Enable Register . . . . . . . . . . . . . . . . . . .
4.2.9 Transmit Descriptor Pointer Register . . . . . . . . . .
4.2.10 Transmit Configuration Register . . . . . . . . . . . . .
4.2.11 Receive Descriptor Pointer Register . . . . . . . . . .
4.2.12 Receive Configuration Register . . . . . . . . . . . . .
4.2.13 CLKRUN Control/Status Register . . . . . . . . . . . .
4.2.14 Wake Command/Status Register . . . . . . . . . . . .
4.2.15 Pause Control/Status Register . . . . . . . . . . . . . .
4.2.16 Receive Filter/Match Control Register . . . . . . . .
4.2.17 Receive Filter/Match Data Register . . . . . . . . . .
4.2.18 Receive Filter Logic . . . . . . . . . . . . . . . . . . . . . .
4.2.19 Boot ROM Address Register . . . . . . . . . . . . . . . .
4.2.20 Boot ROM Data Register . . . . . . . . . . . . . . . . . .
4.2.21 Silicon Revision Register . . . . . . . . . . . . . . . . . .
4.2.22 Management Information Base Control Register
4.2.23 Management Information Base Registers . . . . . .
ol
e
3.2
4.1.1 Configuration Identification Register . . . . . . . . . . .
4.1.2 Configuration Command and Status Register . . .
4.1.3 Configuration Revision ID Register . . . . . . . . . . .
4.1.4 Configuration Latency Timer Register . . . . . . . . .
4.1.5 Configuration I/O Base Address Register . . . . . . .
4.1.6 Configuration Memory Address Register . . . . . . .
4.1.7 Configuration Subsystem Identification Register .
4.1.8 Boot ROM Configuration Register . . . . . . . . . . . .
4.1.9 Capabilities Pointer Register . . . . . . . . . . . . . . . .
4.1.10 Configuration Interrupt Select Register . . . . . . . .
4.1.11 Power Management Capabilities Register . . . . .
4.1.12 Power Management Control and Status Register
41
42
44
44
45
46
47
49
49
50
51
52
53
55
57
58
59
60
64
64
64
65
66
Internal PHY Registers . . . . . . . . . . . . . . . 67
4.3.1 Basic Mode Control Register . . . . . . . . . . . . . . . .
4.3.2 Basic Mode Status Register . . . . . . . . . . . . . . . . .
4.3.3 PHY Identifier Register #1 . . . . . . . . . . . . . . . . . .
4.3.4 PHY Identifier Register #2 . . . . . . . . . . . . . . . . . .
4.3.5 Auto-Negotiation Advertisement Register . . . . . .
4.3.6 Auto-Negotiation Link Partner Ability Register . . .
4.3.7 Auto-Negotiate Expansion Register . . . . . . . . . . .
4.3.8 Auto-Negotiation Next Page Transmit Register . .
4.3.9 PHY Status Register . . . . . . . . . . . . . . . . . . . . . . .
4.3.10 MII Interrupt Control Register . . . . . . . . . . . . . . .
4.3.11 MII Interrupt Status and Misc. Control Register .
4.3.12 False Carrier Sense Counter Register . . . . . . . .
4.3.13 Receiver Error Counter Register . . . . . . . . . . . . .
4.3.14 100 Mb/s PCS Configuration and Status Register
4.3.15 PHY Control Register . . . . . . . . . . . . . . . . . . . . .
4.3.16 10BASE-T Status/Control Register . . . . . . . . . . .
67
68
69
69
69
70
71
71
72
74
74
75
75
75
76
77
4.4 Recommended Registers Configuration . 78
5.0 Buffer Management . . . . . . . . . . . . . . . . . . 79
3.12 802.3u MII . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.12.1 MII Access Configuration . . . . . . . . . . . . . . . . . . . 29
5.1.1 Descriptor Format . . . . . . . . . . . . . . . . . . . . . . . . . 79
2
www.national.com
DP83815
Table of Contents
5.2
6.6
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . 91
6.6.1 Entering Sleep Mode . . . . . . . . . . . . . . . . . . . . . . 91
6.6.2 Exiting Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . 91
Transmit Architecture . . . . . . . . . . . . . . . 83
6.7 Pin Configuration for Power Management 91
7.0 DC and AC Specifications . . . . . . . . . . . . . 92
5.3 Receive Architecture . . . . . . . . . . . . . . . . 86
7.1 DC Specifications . . . . . . . . . . . . . . . . . . . 92
5.3.1 Receive State Machine . . . . . . . . . . . . . . . . . . . . . 86
7.2 AC Specifications . . . . . . . . . . . . . . . . . . . 93
5.3.2 Receive Data Flow . . . . . . . . . . . . . . . . . . . . . . . . . 88
7.2.1 PCI Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.0 Power Management and Wake-On-LAN. . 89
7.2.2 X1 Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 89
7.2.3 Power On Reset (PCI Active) . . . . . . . . . . . . . . . . 94
6.2 Definitions (for this document only) . . . . . 89
7.2.4 Non Power On Reset . . . . . . . . . . . . . . . . . . . . . . 94
7.2.5 POR PCI Inactive . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.3 Packet Filtering . . . . . . . . . . . . . . . . . . . . 89
7.2.6 PCI Bus Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.4 Power Management . . . . . . . . . . . . . . . . 89
5.2.1 Transmit State Machine . . . . . . . . . . . . . . . . . . . . . 83
5.2.2 Transmit Data Flow . . . . . . . . . . . . . . . . . . . . . . . . 85
6.5
7.2.7 EEPROM Auto-Load . . . . . . . . . . . . . . . . . . . . .
7.2.8 Boot PROM/FLASH . . . . . . . . . . . . . . . . . . . . . .
7.2.9 100BASE-TX Transmit . . . . . . . . . . . . . . . . . . .
7.2.10 10BASE-T Transmit End of Packet . . . . . . . . .
7.2.11 10 Mb/s Jabber Timing . . . . . . . . . . . . . . . . . .
7.2.12 10BASE-T Normal Link Pulse . . . . . . . . . . . . .
7.2.13 Auto-Negotiation Fast Link Pulse (FLP) . . . . . .
7.2.14 Media Independent Interface (MII) . . . . . . . . . .
D0 State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
D1 State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
D2 State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
D3hot State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
D3cold State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Wake-On-LAN (WOL) Mode . . . . . . . . . . 90
6.5.1 Entering WOL Mode . . . . . . . . . . . . . . . . . . . . . . . 90
6.5.2 Wake Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
te
6.4.1
6.4.2
6.4.3
6.4.4
6.4.5
101
102
103
104
104
105
105
106
List of Figures
DP83815 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAC/BIU Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP Physical Layer Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED Loading Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100BASE-TX Transmit Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Binary to MLT-3 conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100 M/bs Receive Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100BASE-TX BLW Event Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EIA/TIA Attenuation vs. Frequency for 0, 50, 100, 130 & 150 meters of CAT V cable . . . . . . .
MLT-3 Signal Measured at AII after 0 meters of CAT V cable. . . . . . . . . . . . . . . . . . . . . . . . . .
MLT-3 Signal Measured at AII after 50 meters of CAT V cable. . . . . . . . . . . . . . . . . . . . . . . . .
MLT-3 Signal Measured at AII after 100 meters of CAT V cable. . . . . . . . . . . . . . . . . . . . . . . .
10BASE-T Twisted Pair Smart Squelch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical MDC/MDIO Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical MDC/MDIO Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pattern Buffer Memory - 180h words (word = 18bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hash Table Memory - 40h bytes addressed on word boundaries . . . . . . . . . . . . . . . . . . . . . . .
Single Descriptor Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Descriptor Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List and Ring Descriptor Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3-1
Table 3-2
Table 4-1
Table 4-2
Table 4-3
Table 5-1
Table 5-2
Table 5-3
Table 5-4
Table 5-5
Table 5-6
Table 6-1
Table 6-2
4B5B Code-Group Encoding/Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Typical MDIO Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Configuration Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Operational Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
MIB Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
DP83815 Descriptor Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
cmdsts Common Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Transmit Status Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Receive Status Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Transmit State Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Receive State Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Power Management Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
PM Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
O
bs
ol
e
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Figure 3-9
Figure 3-10
Figure 3-11
Figure 3-12
Figure 3-13
Figure 3-14
Figure 3-15
Figure 3-16
Figure 4-1
Figure 4-2
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Figure 5-6
Figure 5-7
13
14
16
17
19
21
22
24
25
26
26
26
26
28
30
31
61
63
81
82
82
83
84
86
88
List of Tables
3
www.national.com
DP83815
6.5.3 Exiting WOL Mode . . . . . . . . . . . . . . . . . . . . . . . . 91
5.1.2 Single Descriptor Packets . . . . . . . . . . . . . . . . . . . 81
5.1.3 Multiple Descriptor Packets . . . . . . . . . . . . . . . . . . 82
5.1.4 Descriptor Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
DP83815
1.0 Connection Diagram
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
FXVDD
FXVSS
NC
PHYVDD2
PHYVSS2
TXCLK
TXEN
CRS
COL/MA16
VDDIO3
VSSIO3
TXD3/MA15
TXD2/MA14
TXD1/MA13
TXD0/MA12
PHYVDD1
PHYVSS1
VDDIO2
X2
X1
VSSIO2
RXDV/MA11
RXER/MA10
RXOE
RXD3/MA9
RXD2/MA8
RXD1/MA7
VDDIO1
VSSIO1
RXD0/MA6
RXCLK
MDC
MDIO
MA5
MA4/EECLK
MA3/EEDI
1.1 144 LQFP Package (VNG)
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
MA2/LED100N
MA1/LED10N
MA0/LEDACTN
MD7
MD6
MD5
MD4/EEDO
VDDIO5
VSSIO5
MD3
MD2
MD1/CFGDISN
MD0
MWRN
MRDN
MCSN
EESEL
RESERVED
SUBGND3
MACVDD2
MACVSS2
PWRGOOD
3VAUX
AD0
AD1
AD2
AD3
PCIVDD5
AD4
AD5
PCIVSS5
AD6
AD7
CBEN0
AD8
AD9
te
Pin1
Identification
ol
e
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
DP83815
AD25
AD24
CBEN3
IDSEL
PCIVSS2
AD23
AD22
PCIVDD2
AD21
AD20
AD19
VSSIO4
VDDIO4
AD18
AD17
AD16
CBEN2
PCIVSS3
FRAMEN
IRDYN
TRDYN
PCIVDD3
DEVSELN
STOPN
PERRN
SERRN
PAR
CBEN1
AD15
AD14
PCIVSS4
AD13
AD12
AD11
PCIVDD4
AD10
O
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
bs
SUBGND1
RXAVSS1
RXAVDD1
VREF
RESERVED
NC
NC
RXAVSS2
TPRDM
TPRDP
RXAVDD2
NC
SUBGND2
RESERVED
TXDVSS
TXIOVSS1
TPTDM
TPTDP
TXIOVSS2
TXDVDD
MACVSS1
MACVDD1
PMEN/CLKRUNN
PCICLK
INTAN
RSTN
GNTN
REQN
PCIVSS1
AD31
AD30
AD29
PCIVDD1
AD28
AD27
AD26
Order Number DP83815DVNG
See NS Package Number VNG144A
4
www.national.com
DP83815
1.0 Connection Diagram (Continued)
14
13
12
11
10
9
8
7
6
5
4
3
1
Pin A1
Identification
(Marked on Top)
2
1.2 160 pin LBGA Package (UJB)
A
B
te
C
D
E
G
H
J
K
L
M
bs
N
ol
e
F
O
P
Top View
Order Number DP83815DUJB
See NS Package Number UJB160A
5
www.national.com
DP83815
2.0 Pin Description
PCI Bus Interface
CBEN[3-0]
LBGA Pin
No(s)
66, 67, 68, 70,
71, 72, 73, 74,
78, 79, 81, 82,
83, 86, 87, 88,
101, 102, 104,
105, 106, 108,
109, 110, 112,
113, 115, 116,
118, 119, 120,
121
K3, K2, K4,
L3, L2, M1,
N3, P3, L4
N5, M5, L5,
N6, L6, N7,
P7, N10, L10,
M11, N11,
P12, N12,
M13, M14,
L12, L14,
K13, K14,
K11, J13, J14,
J12
I/O
Address and Data: Multiplexed address and data bus. As a bus
master, the DP83815 will drive address during the first bus phase.
During subsequent phases, the DP83815 will either read or write
data expecting the target to increment its address pointer. As a bus
target, the DP83815 will decode each address on the bus and
respond if it is the target being addressed.
75, 89, 100,
111
N4, L7, M10,
L13
I/O
Bus Command/Byte Enable: During the address phase these
signals define the “bus command” or the type of bus transaction that
will take place. During the data phase these pins indicate which byte
lanes contain valid data. CBEN[0] applies to byte 0 (bits 7-0) and
CBEN[3] applies to byte 3 (bits 31-24) in the Little Endian Mode. In
Big Endian Mode, CBEN[3] applies to byte 0 (bits 31-24) and
CBEN[0] applies to byte 3 (bits 7-0).
60
DEVSELN
95
FRAMEN
91
63
O
GNTN
Description
H4
I
Clock: This PCI Bus clock provides timing for all bus phases. The
rising edge defines the start of each phase. The clock frequency
ranges from 0 to 33 MHz.
P9
I/O
Device Select: As a bus master, the DP83815 samples this signal to
insure that the destination address for the data transfer is recognized
by a PCI target. As a target, the DP83815 asserts this signal low
when it recognizes its address after FRAMEN is asserted.
M7
I/O
Frame: As a bus master, this signal is asserted low to indicate the
beginning and duration of a bus transaction. Data transfer takes
place when this signal is asserted. It is de-asserted before the
transaction is in its final phase. As a target, the device monitors this
signal before decoding the address to check if the current transaction
is addressed to it.
bs
PCICLK
Dir
te
AD[31-0]
LQFP Pin
No(s)
ol
e
Symbol
J2
I
Grant: This signal is asserted low to indicate to the DP83815 that it
has been granted ownership of the bus by the central arbiter. This
input is used when the DP83815 is acting as a bus master.
IDSEL
76
M4
I
Initialization Device Select: This pin is sampled by the DP83815 to
identify when configuration read and write accesses are intended for
it.
INTAN
61
J1
O
Interrupt A: This signal is asserted low when an interrupt condition
occurs as defined in the Interrupt Status Register, Interrupt Mask,
and Interrupt Enable registers.
IRDYN
92
P8
I/O
Initiator Ready: As a bus master, this signal will be asserted low
when the DP83815 is ready to complete the current data phase
transaction. This signal is used in conjunction with the TRYDN
signal. Data transaction takes place at the rising edge of PCICLK
when both IRDYN and TRDYN are asserted low. As a target, this
signal indicates that the master has put the data on the bus.
PAR
99
P10
I/O
Parity: This signal indicates even parity across AD[31-0] and
CBEN[3-0] including the PAR pin. As a master, PAR is asserted
during address and write data phases. As a target, PAR is asserted
during read data phases.
6
www.national.com
DP83815
2.0 Pin Description (Continued)
PCI Bus Interface
LBGA Pin
No(s)
Dir
Description
PERRN
97
N9
I/O
Parity Error: The DP83815 as a master or target will assert this
signal low to indicate a parity error on any incoming data (except for
special cycles). As a bus master, it will monitor this signal on all write
operations (except for special cycles).
REQN
64
J4
O
Request: The DP83815 will assert this signal low to request
ownership of the bus from the central arbiter.
RSTN
62
J3
I
Reset: When this signal is asserted all PCI bus outputs of DP83815
will be tri-stated and the device will be put into a known state.
SERRN
98
L9
I/O
System Error: This signal is asserted low by DP83815 during
address parity errors and system errors if enabled.
STOPN
96
M9
I/O
Stop: This signal is asserted low by the target device to request the
master device to stop the current transaction.
TRDYN
93
N8
I/O
Target Ready: As a master, this signal indicates that the target is
ready for the data during write operation and with the data during
read operation. As a target, this signal will be asserted low when the
(target) device is ready to complete the current data phase
transaction. This signal is used in conjunction with the IRDYN signal.
Data transaction takes place at the rising edge of PCICLK when both
IRDYN and TRDYN are asserted low.
PMEN/
59
ol
e
CLKRUNN
te
LQFP Pin
No(s)
Symbol
H2
I/O
Power Management Event/Clock Run Function: This pin is a dual
function pin. The function of this pin is determined by the
CLKRUN_EN bit 0 of the CLKRUN Control and Status register
(CCSR). Default operation of this pin is PMEN.
Power Management Event: This signal is asserted low by DP83815
to indicate that a power management event has occurred. For pin
connection please refer to Section 6.7.
3VAUX
bs
Clock Run Function: In this mode, this pin is used to indicate when
the PCICLK will be stopped.
122
J11
I
PCI Auxiliary Voltage Sense: This pin is used to sense the
presence of a 3.3V auxiliary supply in order to define the PME
Support available. For pin connection please refer to Section 6.7.
This pin has an internal weak pull down.
123
O
PWRGOOD
H13
I
PCI bus power good: Connected to PCI bus 3.3V power (not
3.3Vaux), this pin is used to sense the presence of PCI bus power.
This pin has an internal weak pull down.
7
www.national.com
DP83815
2.0 Pin Description (Continued)
Media Independent Interface (MII)
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
COL
28
C5
I
Collision Detect: The COL signal is asserted high asynchronously
by the external PMD upon detection of a collision on the medium. It
will remain asserted as long as the collision condition persists.
CRS
29
B5
I
Carrier Sense: This signal is asserted high asynchronously by the
external PMD upon detection of a non-idle medium.
MDC
5
A11
O
Management Data Clock: Clock signal with a maximum rate of 2.5
MHz used to transfer management data for the external PMD on the
MDIO pin.
MDIO
4
C11
I/O
Management Data I/O: Bidirectional signal used to transfer
management information for the external PMD. (See Section 3.12.4
for details on connections when MII is used.)
RXCLK
6
D11
I
Receive Clock: A continuous clock, sourced by an external PMD
device, that is recovered from the incoming data. During 100 Mb/s
operation RXCLK is 25 MHz and during 10 Mb/s this is 2.5 MHz.
12, 11, 10, 7
A9, B9, D10,
B10
I
Receive Data: Sourced from an external PMD, that contains data
aligned on nibble boundaries and are driven synchronous to RXCLK.
RXD[3] is the most significant bit and RXD[0] is the least significant
bit.
O
BIOS ROM Address: During external BIOS ROM access, these
signals become part of the ROM address.
I
Receive Data Valid: Indicates that the external PMD is presenting
recovered and decoded nibbles on the RXD signals, and that RXCLK
is synchronous to the recovered data in 100 Mb/s operation. This
signal will encompass the frame, starting with the Start-of-Frame
delimiter (JK) and excluding any End-of-Frame delimiter (TR).
15
B8
bs
RXDV/MA11
te
RXD3/MA9,
RXD2/MA8,
RXD1/MA7,
RXD0/MA6
Description
ol
e
Symbol
O
RXER/MA10
14
D9
I
O
O
BIOS ROM Address: During external BIOS ROM access, this signal
becomes part of the ROM address.
Receive Error: Asserted high synchronously by the external PMD
whenever it detects a media error and RXDV is asserted in 100 Mb/s
operation.
BIOS ROM Address: During external BIOS ROM access, this signal
becomes part of the ROM address.
RXOE
13
C9
O
Receive Output Enable: Used to disable an external PMD while the
BIOS ROM is being accessed.
TXCLK
31
A4
I
Transmit Clock: A continuous clock that is sourced by the external
PMD. During 100 Mb/s operation this is 25 MHz +/- 100 ppm. During
10 Mb/s operation this clock is 2.5 MHz +/- 100 ppm.
25, 24, 23, 22
B6, C6, A6,
D7
O
Transmit Data: Signals which are driven synchronous to the TXCLK
for transmission to the external PMD. TXD[3] is the most significant
bit and TXD[0] is the least significant bit.
TXD3/MA15,
TXD2/MA14,
TXD1/MA13,
TXD0/MA12
O
TXEN
30
D5
O
BIOS ROM Address: During external BIOS ROM access, these
signals become part of the ROM address.
Transmit Enable: This signal is synchronous to TXCLK and
provides precise framing for data carried on TXD[3-0] for the external
PMD. It is asserted when TXD[3-0] contains valid data to be
transmitted.
Note: MII is normally tri-stated, unless enabled by CFG:EXT_PHY. See Section 4.2.2.
8
www.national.com
DP83815
2.0 Pin Description (Continued)
100BASE-TX/10BASE-T Interface
Symbol
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
Description
TPTDP, TPTDM
54, 53
G1, F1
A-O
Transmit Data: Differential common output driver. This differential
common output is configurable to either 10BASE-T or 100BASE-TX
signaling:
10BASE-T: Transmission of Manchester encoded 10BASE-T packet
data as well as Link Pulses (including Fast Link Pulses for AutoNegotiation purposes).
100BASE-TX: Transmission of ANSI X3T12 compliant MLT-3 data.
TPRDP,
TPRDM
46, 45
D1, C1
te
The DP83815 will automatically configure this common output driver
for the proper signal type as a result of either forced configuration or
Auto-Negotiation.
A-I
Receive Data: Differential common input buffer. This differential
common input can be configured to accept either 100BASE-TX or
10BASE-T signaling:
10BASE-T: Reception of Manchester encoded 10BASE-T packet
data as well as normal Link Pulses and Fast Link Pulses for AutoNegotiation purposes.
ol
e
100BASE-TX: Reception of ANSI X3T12 compliant scrambled MLT-3
data.
The DP83815 will automatically configure this common input buffer
to accept the proper signal type as a result of either forced
configuration or Auto-Negotiation.
bs
BIOS ROM/Flash Interface
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
129
G13
O
BIOS ROM/Flash Chip Select: During a BIOS ROM/Flash
access, this signal is used to select the ROM device.
MD7, MD6, MD5,
MD4/EEDO, MD3,
MD2,
MD1/CFGDISN,
MD0
141, 140, 139,
138, 135, 134,
133, 132
D13, D12,
D14, E11,
E14, F11,
F13, F12
I/O
BIOS ROM/Flash Data Bus: During a BIOS ROM/Flash access
these signals are used to transfer data to or from the ROM/Flash
device.
MA5,
MA4/EECLK,
MA3/EEDI,
MA2/LED100LNK,
MA1/LED10LNK,
MA0/LEDACT
3, 2, 1, 144,
143, 142
B11, A12,
B12, C13,
C12, C14
O
BIOS ROM/Flash Address: During a BIOS ROM/Flash access,
these signals are used to drive the ROM/Flash address.
MWRN
131
F14
O
BIOS ROM/Flash Write: During a BIOS ROM/Flash access, this
signal is used to enable data to be written to the Flash device.
MRDN
130
G11
O
BIOS ROM/Flash Read: During a BIOS ROM/Flash access, this
signal is used to enable data to be read from the Flash device.
Symbol
O
MCSN
Description
MD[5:0] pins have internal weak pull ups.
MD6 and MD7 pins have internal weak pull downs.
Note: DP83815 supports NM27LV010 for the BIOS ROM interface device.
9
www.national.com
DP83815
2.0 Pin Description (Continued)
Clock Interface
LBGA Pin
No(s)
Dir
Description
X1
17
D8
I
Crystal/Oscillator Input: This pin is the primary clock reference
input for the DP83815 and must be connected to a 25 MHz 0.005%
(50ppm) clock source. The DP83815 device supports either an
external crystal resonator connected across pins X1 and X2, or an
external CMOS-level oscillator source connected to pin X1 only.
X2
18
C7
O
Crystal Output: This pin is used in conjunction with the X1 pin to
connect to an external 25 MHz crystal resonator device. This pin
must be left unconnected if an external CMOS oscillator clock source
is utilized. For more information see the definition for pin X1.
Symbol
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
LEDACTN/MA0
142
C14
O
TX/RX Activity: This pin is an output indicating transmit/receive
activity. This pin is driven low to indicate active transmission or
reception, and can be used to drive a low current LED (<6 mA). The
activity event is stretched to a min duration of approximately 50 ms.
LED100N/MA2
144
C13
O
100 Mb/s Link: This pin is an output indicating the 100 Mb/s Link
status. This pin is driven low to indicate Good Link status for 100
Mb/s operation, and can be used to drive a low current LED (<6 mA).
LED10N/MA1
143
C12
O
10 Mb/s Link: This pin is an output indicating the 10 Mb/s Link
status. This pin is driven low to indicate Good Link status for 10 Mb/s
operation, and can be used to drive a low current LED (<6 mA).
Description
bs
ol
e
LED Interface
te
LQFP Pin
No(s)
Symbol
Serial EEPROM Interface
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
128
G14
O
EEPROM Chip Select: This signal is used to enable an external
EEPROM device.
EECLK/MA4
2
A12
O
EEPROM Clock: During an EEPROM access (EESEL asserted),
this pin is an output used to drive the serial clock to an external
EEPROM device.
EEDI/MA3
1
B12
O
EEPROM Data In: During an EEPROM access (EESEL asserted),
this pin is an output used to drive opcode, address, and data to an
external serial EEPROM device.
EEDO/MD4
138
E11
I
EEPROM Data Out: During an EEPROM access (EESEL asserted),
this pin is an input used to retrieve EEPROM serial read data.
Symbol
O
EESEL
Description
This pin has an internal weak pull up.
MD1/CFGDISN
133
F13
I/O
Configuration Disable: When pulled low at power-on time, disables
load of configuration data from the EEPROM. Use 1 KΩ to ground to
disable configuration load.
Note: DP83815 supports FM93C46 for the EEPROM device.
10
www.national.com
DP83815
2.0 Pin Description (Continued)
External Reference Interface
Symbol
VREF
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
Description
40
A2
I
Bandgap Reference: External current reference resistor for internal
Phy bandgap circuitry. The value of this resistor is 9.31 KΩ 1% metal
film (100 ppm/oC) which must be connected from the VREF pin to
analog ground.
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
Description
34, 42, 43, 48
A1, A13, A14,
B3, B13, B14,
D4, F3, F4,
G2, M2, M3,
N1, N2, N13,
N14, P1, P2,
P13, P14
NC
41, 50, 127
D2, E3, H12
These pins are reserved and cannot be connected to any external
logic or net.
O
bs
Reserved
No Connect
ol
e
Symbol
te
No Connects
11
www.national.com
DP83815
2.0 Pin Description (Continued)
Supply Pins
LQFP Pin
No(s)
LBGA Pin
No(s)
Dir
SUBGND1,
SUBGND2,
SUBGND3
37, 49, 126
B2, E1, G12
S
Substrate GND
RXAVDD1,
RXAVDD2
39, 47
C2, E2
S
RX Analog VDD - connect to isolated Aux 3.3V supply VDD
RXAVSS1,
RXAVSS2
38, 44
B1, D3
S
RX Analog GND
TXIOVSS1,
TXIOVSS2
52, 55
F2, G4
S
TX Output driver VSS
TXDVDD
56
H3
S
TX Digital VDD - connect to Aux 3.3V supply VDD
TXDVSS
51
E4
S
TX Digital VSS
MACVDD1,
MACVDD2
58,125
H1, H11
S
Mac/BIU digital core VDD - connect to Aux 3.3V supply VDD
MACVSS1,
MACVSS2
57, 124
G3, H14
S
Mac/BIU digital core VSS
PCIVDD1,
PCIVDD2,
PCIVDD3,
PCIVDD4,
PCIVDD5
69, 80, 94,
107, 117
L1, P5, L8,
M12, K12
S
PCI IO VDD - connect to PCI bus 3.3V VDD
PCIVSS1,
PCIVSS2,
PCIVSS3,
PCIVSS4,
PCIVSS5
65, 77, 90,
103, 114
K1, P4, M8,
P11, L11
S
PCI IO VSS
VDDIO2,
VDDIO4
19, 85
C8, M6
S
Misc. IO VDD - connect to Aux 3.3V supply VDD
VDDIO1,
VDDIO3,
VDDIO5
9, 27, 137
C10, A5, E13
S
Misc. IO VDD - connect to Aux 3.3V supply VDD
ol
e
te
Description
O
bs
Symbol
VSSIO2,
VSSIO4
16, 84
A8, P6
S
Misc. IO VSS
VSSIO1,
VSSIO3,
VSSIO5
8, 26, 136
A10, D6, E12
S
Misc. IO VSS
PHYVDD1,
PHYVDD2
21, 33
B7, B4
S
Phy digital core VDD - connect to Aux 3.3V supply VDD
PHYVSS1,
PHYVSS2
20,32
A7, C4
S
Phy digital core VSS
FSVDD
36
C3
S
Frequency Synthesizer VDD - connect to isolated Aux 3.3V supply
VDD
FSVSS
35
A3
S
Frequency Synthesizer VSS
12
www.national.com
DP83815 consists of a MAC/BIU (Media Access
Controller/Bus Interface Unit), a physical layer interface,
SRAM, and miscellaneous support logic. The MAC/BIU
includes the PCI bus, BIOS ROM and EEPROM interfaces,
TPRDP/M
and an 802.3 MAC. The physical layer interface used is a
single-port version of the 3.3V DsPhyter. Internal memory
consists of one - 0.5 KB and two - 2 KB SRAM blocks.
Test data in
Interface
Logic
ol
e
SRAM
RXFilter
.5 KB
MII RX
MII TX
MII Mgt
BIOS ROM Cntl
BIOS ROM Data
EEPROM/LEDs
BROM/EE
MII TX
MII RX
MII Mgt
Rx Addr
Rx wr data
Tx wr data
Tx Addr
bs
Rx rd data
SRAM
TX-2 KB
Tx rd data
TPTDP/M
te
RAM
BIST
Logic
Test data out
SRAM
RX-2 KB
MII TX
25 MHz Clk
MII RX
MII Mgt
3V DSP Physical Layer
PCI CLK
PCI CNTL
MAC/BIU
O
PCI AD
DP83815
Figure 3-1 DP83815 Functional Block Diagram
13
www.national.com
DP83815
3.0 Functional Description
DP83815
3.0 Functional Description (Continued)
32
15
32
Data FIFO
4
32
Tx Buffer Manager
32
32
PCI Bus
Interface
32
Data FIFO
4
Rx MAC
te
PCI Bus
32
Rx Buffer Manager
MIB
ol
e
32
32
Rx Filter
Pkt Recog
Logic
16
SRAM
Physical Layer Interface
Tx MAC
bs
MAC/BIU
O
93C46
Serial
EEPROM
Boot ROM/
Flash
Figure 3-2 MAC/BIU Functional Block Diagram
3.1 MAC/BIU
The MAC/BIU is a derivative design from the DP83810
(Euphrates). The original MAC/BIU design has been
optimized to improve logic efficiency and enhanced to add
features consistent with current market needs and
specification compliance. The MAC/BIU design blocks are
discussed in this section.
control, serial EEPROM access with auto configuration
load, interrupt control, power management control with
support for PME or CLKRUN function.
3.1.1.1 Byte Ordering
The DP83815 can be configured to order the bytes of data
on the AD[31:0] bus to conform to little endian or big
3.1.1 PCI Bus Interface
endian ordering through the use of the Configuration
This block implements PCI v2.2 bus protocols, and Register, bit 0 (CFG:BEM). By default, the device is in little
configuration space. Supports bus master reads and writes endian ordering. Byte ordering only affects data FIFOs.
to CPU memory, and CPU access to on-chip register Register information remains bit aligned (i.e. AD[31] maps
space. Additional functions provided include: configuration to bit 31 in any register space, AD[0] maps to bit 0, etc.).
Subject to change without notice.
14
Rev O
www.national.com
3.2 Buffer Management
Little Endian (CFG:BEM=0): The byte orientation for
receive and transmit data in system memory is as follows:
31
24 23
16 15
8 7
The buffer management scheme used on the DP83815
allows quick, simple and efficient use of the frame buffer
memory. Frames are saved in similar formats for both
transmit and receive. The buffer management scheme also
uses separate buffers and descriptors for packet
information. This allows effective transfers of data from the
receive buffer to the transmit buffer by simply transferring
the descriptor from the receive queue to the transmit
queue.
0
Byte 3
Byte 2
Byte 1
Byte 0
MSB
C/BE[3]
C/BE[2]
C/BE[1]
LSB
C/BE[0]
Big Endian (CFG:BEM=1): The byte orientation for
receive and transmit data in system memory is as follows:
24 23
16 15
8 7
Byte 0
Byte 1
Byte 2
LSB
C/BE[3]
C/BE[2]
C/BE[1]
0
te
31
The format of the descriptors allows the packets to be
saved in a number of configurations. A packet can be
stored in memory with a single descriptor per single packet,
or multiple descriptors per single packet. This flexibility
allows the user to configure the DP83815 to maximize
efficiency. Architecture of the specific system’s buffer
memory, as well as the nature of network traffic, will
determine the most suitable configuration of packet
descriptors and fragments. Refer to the Buffer
Management Section (Section 5.0) for more information.
Byte 3
MSB
C/BE[0]
3.2.1 Tx Buffer Manager
bs
ol
e
This block DMAs packet data from PCI memory space and
places it in the 2 KB transmit FIFO, and pulls data from the
FIFO to send to the Tx MAC. Multiple packets (4) may be
present in the FIFO, allowing packets to be transmitted with
3.1.1.2 PCI Bus Interrupt Control
minimum interframe gap. The way in which the FIFO is
PCI bus interrupts for the DP83815 are asynchronously
emptied and filled is controlled by the FIFO threshold
performed by asserting pin INTAN. This pin is an open
values in the TXCFG register: FLTH (Tx Fill Threshold) and
drain output. The source of the interrupt can be determined
DRTH (Tx Drain Threshold). These values determine how
by reading the Interrupt Status Register (ISR). One or more
full or empty the FIFO must be before the device requests
bits in the ISR will be set, denoting all currently pending
the bus. Additionally, once the DP83815 requests the bus,
interrupts. Caution: Reading of the ISR clears ALL bits.
it will attempt to empty or fill the FIFO as allowed by the
Masking of specified interrupts can be accomplished by
MXDMA setting in the TXCFG register.
using the Interrupt Mask Register (IMR).
3.1.1.3 Timer
O
The Latency Timer described in CFGLAT:LAT defines the
minimum number of bus clocks that the device will hold the
bus. Once the device gains control of the bus and issues
FRAMEN, the Latency Timer will begin counting down. If
GNTN is de-asserted before the DP83815 has finished
with the bus, the device will maintain ownership of the bus
until the timer reaches zero (or has finished the bus
transfer). The timer is an 8-bit counter.
3.1.2 Tx MAC
This block implements the transmit portion of 802.3 Media
Access Control. The Tx MAC retrieves packet data from
the Tx Buffer Manager and sends it out through the
transmit portion. Additionally, the Tx MAC provides MIB
control information for transmit packets.
3.1.3 Rx MAC
This block implements the receive portion of 802.3 Media
Access Control. The Rx MAC retrieves packet data from
the receive portion and sends it to the Rx Buffer Manager.
Additionally, the Rx MAC provides MIB control information
and packet address data for the Rx Filter.
Subject to change without notice.
3.2.2 Rx Buffer Manager
This block retrieves packet data from the Rx MAC and
places it in the 2 KB receive data FIFO, and pulls data from
the FIFO for DMA to PCI memory space. The Rx Buffer
Manager maintains a status FIFO, allowing up to 4 packets
to reside in the FIFO at once. Similar to the transmit FIFO,
the receive FIFO is controlled by the FIFO threshold value
in the RXCFG register: DRTH (Rx Drain Threshold). This
value determines the number of long words written into the
FIFO from the MAC unit before a DMA request for system
memory access occurs. Once the DP83815 gets the bus, it
will continue to transfer the long words from the FIFO until
the data in the FIFO is less than one long word, or has
reached the end of the packet, or the max DMA burst size
is reached (RXCFG:MXDMA).
3.2.3 Packet Recognition
The Receive packet filter and recognition logic allows
software to control which packets are accepted based on
destination address and packet type. Address recognition
logic includes support for broadcast, multicast hash, and
unicast addresses. The packet recognition logic includes
support for WOL, Pause, and programmable pattern
recognition.
15
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
3.3.2 Boot PROM
The standard 802.3 Ethernet packet consists of the
following fields: Preamble (PA), Start of Frame Delimiter
(SFD), Destination Address (DA), Source Address (SA),
Length (LEN), Data and Frame Check Sequence (FCS). All
fields are fixed length except for the data field. During
reception, the PA, SFD and FCS are stripped. During
transmission, the DP83815 generates and appends the
PA, SFD and FCS.
PA
SFD DA
60b
4b
6B
SA
LEN
Data
FCS
6B
2B
46B-1500B
4B
The BIOS ROM interface allows the DP83815 to read from
and write data to an external ROM/Flash device.
3.3.3 EEPROM
Figure 3-3 Ethernet Packet Format
3.3.4 Clock
3.2.4 MIB
3.3.1 PCI System Bus
The clock interface provides the 25 MHz clock reference
input for the DP83815 IC. The X1 and X2 pin capacitances
are 4.5 + 1.0pF. The X1 input signal amplitude should be
approximately 1V. This interface supports operation from a
25 MHz, 50 ppm CMOS oscillator, or a 25 MHz, 50 ppm,
parallel, 20 pF load, < 40 Ω ESR crystal resonator. A 20pF
crystal resonator would require C1 and C2 load capacitors
of 27-33pF each.
ol
e
The MIB block contains counters to track certain media
events required by the management specifications RFC
1213 (MIB II), RFC 1398 (Ether-like MIB), and IEEE 802.3
LME. The counters provided are for events which are either
difficult or impossible to be intercepted directly by software.
Not all counters are implemented, however required
counters can be calculated from the counters provided.
3.3 Interface Definitions
te
Note: B = Bytes
b = bits
The DP83815 supports the attachment of an external
EEPROM. The EEPROM interface provides the ability for
the DP83815 to read from and write data to an external
serial EEPROM device. The DP83815 will auto-load values
from the EEPROM to certain fields in PCI configuration
space and operational space and perform a checksum to
verify that the data is valid. Values in the external EEPROM
allow default fields in PCI configuration space and I/O
space to be overridden following a hardware reset. If the
EEPROM is not present, the DP83815 initialization uses
default values for the appropriate Configuration and
Operational Registers. Software can read and write to the
EEPROM using “bit-bang” accesses via the EEPROM
Access Register (MEAR).
O
bs
This interface allows direct connection of the DP83815 to a
33 MHz PCI system bus. The DP83815 supports zero wait
state data transfers with burst sizes up to 128 dwords. The
DP83815 conforms to 3.3V AC/DC specifications, but has
5V tolerant inputs.
Subject to change without notice.
16
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
DP83815
3.0 Functional Description (Continued)
POWER ON
CONFIGURATION
PINS
TX_DATA
TX_DATA
TXCLK
TRANSMIT CHANNELS &
STATE MACHINES
4B/5B
ENCODER
SCRAMBLER
PARALLEL TO
SERIAL
NRZ TO NRZI
ENCODER
MII
10 MB/S
RXCLK
RECEIVE CHANNELS &
STATE MACHINES
REGISTERS
PHY ADDRESS
NRZ TO
MANCHESTER
ENCODER
100 MB/S
4B/5B
DECODER
LINK PULSE
GENERATOR
CODE GROUP
ALIGNMENT
PCS CONTROL
DESCRAMBLER
10BASE-T
SERIAL TO
PARALLEL
100BASE-X
TRANSMIT
FILTER
FAR-END-FAULT
STATE MACHINE
10/100 COMMON
OUTPUT DRIVER
NRZI TO NRZ
DECODER
CLOCK
RECOVERY
LINK PULSE
DETECTOR
CLOCK
RECOVERY
RECEIVE
FILTER
MLT-3 TO
BINARY
DECODER
AUTO-NEGOTIATION
STATE MACHINE
O
10 MB/S
MANCHESTER
TO NRZ
DECODER
AUTO
NEGOTIATION
BASIC MODE
CONTROL
bs
BINARY TO
MLT-3
ENCODER
RXCLK
ol
e
100 MB/S
RX_DATA
RX_DATA
te
RXCLK
RXD(3:0)
RXDV
RXER
RXEN
CRS
COL
MDC
MDIO
TXEN
TXER
TXCLK
TXD(3:0)
SERIAL
MANAGEMENT
NCLK_50M
MAC INTERFACE
ADAPTIVE
EQ
AND
BLW
COMP.
SMART
SQUELCH
10/100 COMMON
INPUT BUFFER
CLOCK
GENERATION
LED
DRIVERS
TD±
LEDS
RD±
(ALSO FX_RD±)
SYSTEM CLOCK
REFERENCE
Figure 3-4 DSP Physical Layer Block Diagram
Subject to change without notice.
17
Rev O
www.national.com
3.4 Physical Layer
operation when the Auto-Negotiation Enable bit (bit 12) is
set.
The DP83815 has a full featured physical layer device with
integrated PMD sub-layers to support both 10BASE-T and
100BASE-TX Ethernet protocols. The physical layer is
designed for easy implementation of 10/100 Mb/s Ethernet
home or office solutions. It interfaces directly to twisted pair
media via an external transformer. The physical layer
utilizes on chip Digital Signal Processing (DSP) technology
and digital PLLs for robust performance under all operating
conditions, enhanced noise immunity, and lower external
component count when compared to analog solutions.
The Basic Mode Status Register (BMSR) indicates the set
of available abilities for technology types, Auto-Negotiation
ability, and Extended Register Capability. These bits are
permanently set to indicate the full functionality of the
DP83815 (only the 100BASE-T4 bit is not set since the
DP83815 does not support that function).
The BMSR also provides status on:
— Auto-Negotiation complete (bit 5)
The Auto-Negotiation function provides a mechanism for — Link Partner advertising that a remote fault has occurred
(bit 4)
exchanging configuration information between two ends of
a link segment and automatically selecting the highest — Valid link has been established (bit 2)
performance mode of operation supported by both devices. — Support for Management Frame Preamble suppression
Fast Link Pulse (FLP) Bursts provide the signalling used to
(bit 6)
communicate Auto-Negotiation abilities between two
The Auto-Negotiation Advertisement Register (ANAR)
devices at each end of a link segment. For further detail
indicates the Auto-Negotiation abilities to be advertised by
regarding Auto-Negotiation, refer to Clause 28 of the IEEE
the DP83815. All available abilities are transmitted by
802.3u specification. The DP83815 supports four different
default, but any ability can be suppressed by writing to the
Ethernet protocols (10 Mb/s Half Duplex, 10 Mb/s Full
ANAR. Updating the ANAR to suppress an ability is one
Duplex, 100 Mb/s Half Duplex, and 100 Mb/s Full Duplex),
way for a management agent to change (force) the
so the inclusion of Auto-Negotiation ensures that the
technology that is used.
highest performance protocol will be selected based on the
advertised ability of the Link Partner. The Auto-Negotiation The Auto-Negotiation Link Partner Ability Register
function within the DP83815 is controlled by internal (ANLPAR) is used to receive the base link code word as
register access. Auto-Negotiation will be set at power- well as all next page code words during the negotiation.
up/reset, and also when a link status (up/valid) change Furthermore, the ANLPAR will be updated to either 0081h
or 0021h for parallel detection to either 100 Mb/s or 10
occurs.
Mb/s respectively.
3.4.2 Auto-Negotiation Register Control
The Auto-Negotiation Expansion Register (ANER)
When Auto-Negotiation is enabled, the DP83815 transmits
indicates additional Auto-Negotiation status. The ANER
the abilities programmed into the Auto-Negotiation
provides status on:
Advertisement register (ANAR) via FLP Bursts. Any
combination of 10 Mb/s, 100 Mb/s, Half-Duplex, and Full — Parallel Detect Fault occurrence (bit 4)
Duplex modes may be selected. The default setting of bits — Link Partner support of the Next Page function (bit 3)
[8:5] in the ANAR and bit 12 in the BMCR register are
— DP83815 support of the Next Page function (bit 2). The
determined at power-up.
DP83815 supports the Next Page function.
The BMCR provides software with a mechanism to control — Current page being exchanged by Auto-Negotiation has
the operation of the DP83815. Bits 1 & 2 of the PHYSTS
been received (bit1)
register are only valid if Auto-Negotiation is disabled or
—
Link
Partner support of Auto-Negotiation (bit 0)
after Auto-Negotiation is complete. The Auto-Negotiation
protocol compares the contents of the ANLPAR and ANAR 3.4.3 Auto-Negotiation Parallel Detection
registers and uses the results to automatically configure to
The DP83815 supports the Parallel Detection function as
the highest performance protocol common to the local and
defined in the IEEE 802.3u specification. Parallel Detection
far-end port. The results of Auto-Negotiation may be
requires both the 10 Mb/s and 100 Mb/s receivers to
accessed in register C0h (PHYSTS), bit 4: Automonitor the receive signal and report link status to the
Negotiation Complete, bit 2: Duplex Status and bit 1:
Auto-Negotiation function. Auto-Negotiation uses this
Speed Status.
information to configure the correct technology in the event
Auto-Negotiation Priority Resolution:
that the Link Partner does not support Auto-Negotiation yet
is transmitting link signals that the 100BASE-TX or
— (1) 100BASE-TX Full Duplex (Highest Priority)
10BASE-T PMAs (Physical Medium Attachments)
— (2) 100BASE-TX Half Duplex
recognize as valid link signals.
— (3) 10BASE-T Full Duplex
If the DP83815 completes Auto-Negotiation as a result of
— (4) 10BASE-T Half Duplex (Lowest Priority)
Parallel Detection, bits 5 and 7 within the ANLPAR register
The Basic Mode Control Register (BMCR) provides control will be updated to reflect the mode of operation present in
for enabling, disabling, and restarting the Auto-Negotiation the Link Partner. Note that bits 4:0 of the ANLPAR will also
process. When Auto-Negotiation is disabled the Speed be set to 00001 based on a successful parallel detection to
Selection bit in the BCMR (bit 13) controls switching indicate a valid 802.3 selector field. Software may
between 10 Mb/s or 100 Mb/s operation, and the Duplex determine that negotiation completed via Parallel Detection
Mode bit (bit 8) controls switching between full duplex by reading the ANER (98h) register with bit 0, Link Partner
operation and half duplex operation. The Speed Selection Auto-Negotiation Able bit, being reset to a zero, once the
and Duplex Mode bits have no effect on the mode of Auto-Negotiation Complete bit, bit 5 of the BMSR (84h)
O
bs
ol
e
te
3.4.1 Auto-Negotiation
Subject to change without notice.
18
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
The LED100N pin indicates a good link at 100 Mb/s data
rate. The standard CMOS driver goes low when this
occurs. In 100BASE-T mode, link is established as a result
of input receive amplitude compliant with TP-PMD
specifications which will result in internal generation of
signal detect. This signal will assert after the internal Signal
Detect has remained asserted for a minimum of 500 us.
The signal will de-assert immediately following the deassertion of the internal signal detect.
register is set to a one. If configured for parallel detect
mode, and any condition other than a single good link
occurs, then the parallel detect fault bit will set to a one, bit
4 of the ANER register (98h).
3.4.4 Auto-Negotiation Restart
Once Auto-Negotiation has completed, it may be restarted
at any time by setting bit 9 (Restart Auto-Negotiation) of the
BMCR to one. If the mode configured by a successful AutoNegotiation loses a valid link, then the Auto-Negotiation
process will resume and attempt to determine the
configuration for the link. This function ensures that a valid
configuration is maintained if the cable becomes
disconnected.
LED100N
LEDACTN
ol
e
It is important to note that if the DP83815 has been
initialized upon power-up as a non-auto-negotiating device
(forced technology), and it is then required that AutoNegotiation or re-Auto-Negotiation be initiated via software,
bit 12 (Auto-Negotiation Enable) of the Basic Mode Control
Register must first be cleared and then set for any AutoNegotiation function to take effect.
LED10N
3.4.5 Enabling Auto-Negotiation via Software
te
The LED10N pin indicates a good link at 10 Mb/s data rate.
The standard CMOS driver goes low when this occurs. 10
Mb/s Link is established as a result of the reception of at
least seven consecutive normal Link Pulses or the
reception of a valid 10BASE-T packet. This will cause the
A renegotiation request from any entity, such as a assertion of this signal. the signal will de-assert in
management agent, will cause the DP83815 to halt any accordance with the Link Loss Timer as specified in IEEE
transmit data and link pulse activity until the 802.3.
break_link_timer expires (~1500 ms). Consequently, the
Link Partner will go into link fail and normal Auto- The DP83815 LED pins are capable of 6 mA. Connection
Negotiation resumes. The DP83815 will resume Auto- of these LED pins should ensure this is not overloaded.
Negotiation after the break_link_timer has expired by Using 2 mA LED devices the connection for the LEDs
could be as shown in Figure 3-5.
issuing FLP (Fast Link Pulse) bursts.
453 Ω
453 Ω
Parallel detection and Auto-Negotiation take approximately
2-3 seconds to complete. In addition, Auto-Negotiation with
next page should take approximately 2-3 seconds to
complete, depending on the number of next pages sent.
453 Ω
3.4.6 Auto-Negotiation Complete Time
bs
Refer to Clause 28 of the IEEE 802.3u standard for a full
description of the individual timers related to AutoNegotiation.
VDD
3.5 LED Interfaces
Figure 3-5 LED Loading Example
O
The DP83815 has parallel outputs to indicate the status of
Activity (Transmit or Receive), 100 Mb/s Link, and 10 Mb/s
Link.
The LEDACTN pin indicates the presence of transmit or
receive activity. The standard CMOS driver goes low when
RX or TX activity is detected in either 10 Mb/s or 100 Mb/s
operation.
Subject to change without notice.
19
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
3.6 Half Duplex vs. Full Duplex
In 100BASE-TX Loopback mode the data is routed through
the PCS and PMA layers into the PMD sublayer before it is
The DP83815 supports both half and full duplex operation
looped back. Therefore, in addition to serving as a board
at both 10 Mb/s and 100 Mb/s speeds.
diagnostic, this mode serves as quick functional verification
Half-duplex is the standard, traditional mode of operation of the device.
which relies on the CSMA/CD protocol to handle collisions
Note: A Mac Loopback can be performed via setting bit 29
and network access. In Half-Duplex mode, CRS responds
(Mac Loopback) in the Tx Configuration Register.
to both transmit and receive activity in order to maintain
3.8 Status Information
compliance with IEEE 802.3 specification.
There are 3 pins that are available to convey status
information to the user through LEDs to indicate the speed
(10 Mb/s or 100 Mb/s) link status and receive or transmit
activity.
Since the DP83815 is designed to support simultaneous
transmit and receive activity it is capable of supporting fullduplex switched applications with a throughput of up to 200
Mb/s per port when operating in 100BASE-TX mode.
Because the CSMA/CD protocol does not apply to fullduplex operation, the DP83815 disables its own internal
collision sensing and reporting functions.
te
100BASE-T Link is established as a result of an input
receive amplitude compliant with TP-PMD specifications
which will result in internal generation of Signal Detect.
LED100N will assert after the internal Signal Detect has
remained asserted for a minimum of 500 µs. LED100N will
de-assert immediately following the de-assertion of the
internal Signal Detect.
ol
e
It is important to understand that while full Auto-Negotiation
with the use of Fast Link Pulse code words can interpret
and configure to support full-duplex, parallel detection can
not recognize the difference between full and half-duplex
from a fixed 10 Mb/s or 100 Mb/s link partner over twisted
pair. Therefore, as specified in 802.3u, if a far-end link
partner is transmitting forced full duplex 100BASE-TX for
example, the parallel detection state machine in the
receiving station would be unable to detect the full duplex
capability of the far-end link partner and would negotiate to
a half duplex 100BASE-TX configuration (same scenario
for 10 Mb/s).
10 Mb/s Link is established as a result of the reception of at
least seven consecutive Normal Link Pulses or the
reception of a valid 10BASE-T packet. LED10N will deassert in accordance with the Link Loss Timer specified in
IEEE 802.3.
For full duplex operation, the following register bits must
also be set:
bs
— TXCFG:CSI (Carrier Sense Ignore)
— TXCFG:HBI (HeartBeat Ignore)
— RXCFG:ATX (Accept Transmit Packets)
Additionally, the Auto-Negotiation Select bits in the
Configuration register must show full duplex support:
— CFG:ANEG_SEL
Activity LED status indicates Receive or Transmit activity.
3.9 100BASE-TX TRANSMITTER
The 100BASE-TX transmitter consists of several functional
blocks which convert synchronous 4-bit nibble data, to a
scrambled MLT-3 125 Mb/s serial data stream. Because
the 100BASE-TX TP-PMD is integrated, the differential
output pins, TD±, can be directly routed to the magnetics.
The block diagram in Figure 3-6 provides an overview of
each functional block within the 100BASE-TX transmit
section.
The Transmitter section consists of the following functional
blocks:
O
— Code-group Encoder and Injection block (bypass option)
— Scrambler block (bypass option)
3.7 Phy Loopback
The DP83815 includes a Phy Loopback Test mode for — NRZ to NRZI encoder block
easy board diagnostics. The Loopback mode is selected — Binary to MLT-3 converter / Common Driver
through bit 14 (Loopback) of the Basic Mode Control The bypass option for the functional blocks within the
Register (BMCR). Writing 1 to this bit enables transmit data 100BASE-TX transmitter provides flexibility for applications
to be routed to the receive path early in the physical layer such as 100 Mb/s repeaters where data conversion is not
cell. Loopback status may be checked in bit 3 of the PHY always required. The DP83815 implements the 100BASEStatus Register (C0h). While in Loopback mode the data TX transmit state machine diagram as specified in the
will not be transmitted onto the media. This is true for either IEEE 802.3u Standard, Clause 24.
10 Mb/s as well as 100 Mb/s data.
Subject to change without notice.
20
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
DP83815
3.0 Functional Description (Continued)
TXCLK
TXD(3:0)/TXER
FROM CGM
4B5B CODEGROUP ENABLER
MUX
BP_4B5B
te
5B PARALLEL
TO SERIAL
SCRAMBLER
MUX
ol
e
BP_SCR
MUX
NRZ TO NRZI
ENCODER
O
bs
100BASE-TX
LOOPBACK
BINARY
TO MLT-3/
COMMON
DRIVER
TD +/-
Figure 3-6 100BASE-TX Transmit Block Diagram
3.9.1 Code-group Encoding and Injection
3.9.2 Scrambler
The code-group encoder converts 4-bit (4B) nibble data
generated by the MAC into 5-bit (5B) code-groups for
transmission. This conversion is required to allow control
data to be combined with packet data code-groups. Refer
to Table 3-1 for 4B to 5B code-group mapping details.
The scrambler is required to control the radiated emissions
at the media connector and on the twisted pair cable (for
100BASE-TX applications). By scrambling the data, the
total energy launched onto the cable is randomly
distributed over a wide frequency range. Without the
scrambler, energy levels at the PMD and on the cable
could peak beyond FCC limitations at frequencies related
to repeating 5B sequences (i.e., continuous transmission
of IDLEs).
The code-group encoder substitutes the first 8-bits of the
MAC preamble with a J/K code-group pair (11000 10001)
upon transmission. The code-group encoder continues to
replace subsequent 4B preamble and data nibbles with
corresponding 5B code-groups. At the end of the transmit
packet, upon the de-assertion of Transmit Enable signal
from the MAC, the code-group encoder injects the T/R
code-group pair (01101 00111) indicating the end of frame.
After the T/R code-group pair, the code-group encoder
continuously injects IDLEs into the transmit data stream
until the next transmit packet is detected (re-assertion of
Transmit Enable).
Subject to change without notice.
The scrambler is configured as a closed loop linear
feedback shift register (LFSR) with an 11-bit polynomial.
The output of the closed loop LFSR is X-ORd with the
serial NRZ data from the code-group encoder. The result is
a scrambled data stream with sufficient randomization to
decrease radiated emissions at certain frequencies by as
much as 20 dB.
21
Rev O
www.national.com
3.9.3 NRZ to NRZI Encoder
3.9.4 Binary to MLT-3 Convertor / Common Driver
After the transmit data stream has been serialized and
scrambled, the data must be NRZI encoded in order to
comply with the TP-PMD standard for 100BASE-TX
transmission over Category-5 un-shielded twisted pair
cable. There is no ability to bypass this block within the
DP83815.
The Binary to MLT-3 conversion is accomplished by
converting the serial binary data stream output from the
NRZI encoder into two binary data streams with alternately
phased logic one events. These two binary streams are
then fed to the twisted pair output driver which converts the
voltage to current and alternately drives either side of the
transmit transformer primary winding, resulting in a minimal
current (20 mA max) MLT-3 signal. Refer to Figure 3-7
binary_in
binary_plus
Q
D
binary_minus
te
differential MLT-3
Q
binary_plus
binary_in
COMMON
DRIVER
MLT-3
ol
e
binary_minus
Figure 3-7 Binary to MLT-3 conversion
Table 3-1 4B5B Code-Group Encoding/Decoding
O
bs
Name
PCS 5B Code-group
DATA CODES
0
11110
1
01001
2
10100
3
10101
4
01010
5
01011
6
01110
7
01111
8
10010
9
10011
A
10110
B
10111
C
11010
D
11011
E
11100
F
11101
IDLE AND CONTROL CODES
H
00100
I
11111
J
11000
K
10001
T
01101
R
00111
Subject to change without notice.
22
Description/4B Value
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
HALT code-group - Error code
Inter-Packet IDLE - 0000
First Start of Packet - 0101
Second Start of Packet - 0101
First End of Packet - 0000
Second End of Packet - 0000
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
DP83815
3.0 Functional Description (Continued)
Table 3-1 4B5B Code-Group Encoding/Decoding
PCS 5B Code-group
Description/4B Value
00000
00001
00010
00011
00101
00110
01000
01100
10000
11001
The 100BASE-TX MLT-3 signal sourced by the TD±
common driver output pins is slew rate controlled. This
should be considered when selecting AC coupling
magnetics to ensure TP-PMD Standard compliant
transition times (3 ns < Tr < 5 ns).
3.10.1 Input and Base Line Wander Compensation
Unlike the DP83223V Twister, the DP83815 requires no
external attenuation circuitry at its receive inputs, RD+/−. It
accepts TP-PMD compliant waveforms directly, requiring
only a 100Ω termination plus a simple 1:1 transformer.
The DP83815 is completely ANSI TP-PMD compliant and
includes Base Line Wander (BLW) compensation. The
BLW compensation block can successfully recover the TPPMD defined “killer” pattern and pass it to the digital
adaptive equalization block.
ol
e
The 100BASE-TX transmit TP-PMD function within the
DP83815 is capable of sourcing only MLT-3 encoded data.
Binary output from the TD± outputs is not possible in 100
Mb/s mode.
te
Name
INVALID CODES
V
V
V
V
V
V
V
V
V
V
3.10 100BASE-TX Receiver
bs
The 100BASE-TX receiver consists of several functional
blocks which convert the scrambled MLT-3 125 Mb/s serial
data stream to synchronous 4-bit nibble data that is
provided to the MAC. Because the 100BASE-TX TP-PMD
is integrated, the differential input pins, RD±, can be
directly routed from the AC coupling magnetics.
See Figure 3-8 for a block diagram of the 100BASE-TX
receive function. This provides an overview of each
functional block within the 100BASE-TX receive section.
The Receive section consists of the following functional
blocks:
O
— ADC
— Input and BLW Compensation
— Signal Detect
— Digital Adaptive Equalization
— MLT-3 to Binary Decoder
— Clock Recovery Module
— NRZI to NRZ Decoder
— Serial to Parallel
— De-scrambler (bypass option)
— Code Group Alignment
— 4B/5B Decoder (bypass option)
— Link Integrity Monitor
— Bad SSD Detection
The bypass option for the functional blocks within the
100BASE-TX receiver provides flexibility for applications
such as 100 Mb/s repeaters where data conversion is not
always required.
Subject to change without notice.
BLW can generally be defined as the change in the
average DC content, over time, of an AC coupled digital
transmission over a given transmission medium. (i.e.
copper wire).
BLW results from the interaction between the low
frequency components of a transmitted bit stream and the
frequency response of the AC coupling component(s)
within the transmission system. If the low frequency
content of the digital bit stream goes below the low
frequency pole of the AC coupling transformers then the
droop characteristics of the transformers will dominate
resulting in potentially serious BLW.
The digital oscilloscope plot provided in Figure 3-9
illustrates the severity of the BLW event that can
theoretically be generated during 100BASE-TX packet
transmission. This event consists of approximately 800 mV
of DC offset for a period of 120 us. Left uncompensated,
events such as this can cause packet loss.
3.10.2 Signal Detect
The signal detect function of the DP83815 is incorporated
to meet the specifications mandated by the ANSI FDDI TPPMD Standard as well as the IEEE 802.3 100BASE-TX
Standard for both voltage thresholds and timing
parameters.
Note that the reception of normal 10BASE-T link pulses
and fast link pulses per IEEE 802.3u Auto-Negotiation by
the 100BASE-TX receiver do not cause the DP83815 to
assert signal detect.
23
Rev O
www.national.com
SD
RXD(3:0)/RXER
RXCLK
BP_RX
MUX
MUX
BP_4B5B
4B/5B DECODER
LINK INTEGRITY
MONITOR
te
SERIAL TO
PARALLEL
RX_DATA VALID
CODE GROUP
ALIGNMENT
ol
e
SSD DETECT
MUX
BP_SCR
DESCRAMBLER
CLOCK
CLOCK
NRZI TO NRZ
DECODER
bs
RECOVERY
MODULE
O
MLT-3 TO BINARY
DECODER
DIGITAL
ADAPTIVE
EQUALIZATION
AGC
SIGNAL
DETECT
INPUT BLW
COMPENSATION
ADC
RD +/-
Figure 3-8 100 M/bs Receive Block Diagram
Subject to change without notice.
24
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
DP83815
ol
e
te
3.0 Functional Description (Continued)
Figure 3-9 100BASE-TX BLW Event Diagram
it is sensitive to transformer mismatch, resistor variation
and process induced offset. The DP83223V also required
When transmitting data at high speeds over copper twisted
an external attenuation network to help match the incoming
pair cable, frequency dependent attenuation becomes a
signal amplitude to the internal reference.
concern. In high-speed twisted pair signalling, the
frequency content of the transmitted signal can vary greatly The Digital Equalizer removes ISI (Inter Symbol
during normal operation based primarily on the Interference) from the receive data stream by continuously
randomness of the scrambled data stream. This variation adapting to provide a filter with the inverse frequency
in signal attenuation caused by frequency variations must response of the channel. When used in conjunction with a
be compensated for to ensure the integrity of the gain stage, this enables the receive 'eye pattern' to be
opened sufficiently to allow very reliable data recovery.
transmission.
bs
3.10.3 Digital Adaptive Equalization
Traditionally 'adaptive' equalizers selected 1 of N filters in
an attempt to match the cables characteristics. This
approach will typically leave holes at certain cable lengths,
where the performance of the equalizer is not optimized.
The DP83815 equalizer is truly adaptive.
The DP83815 utilizes an extremely robust equalization
scheme referred to herein as ‘Digital Adaptive
Equalization’. Traditional designs use a pseudo adaptive
equalization scheme that determines the approximate
cable length by monitoring signal attenuation at certain
frequencies. This attenuation value was compared to the
internal receive input reference voltage. This comparison
would indicate the amount of equalization to use. Although
this scheme is used successfully on the DP83223V twister,
Figure 3-11 represents a scrambled IDLE transmitted over
zero meters of cable as measured at the AII (Active Input
Interface) of the receiver. Figure 3-12 and Figure 3-13
represent the signal degradation over 50 and 100 meters
of category V cable respectively, also measured at the AII.
These plots show the extreme degradation of signal
integrity and indicate the requirement for a robust adaptive
equalizer.
O
In order to ensure quality transmission when employing
MLT-3 encoding, the compensation must be able to adapt
to various cable lengths and cable types depending on the
installed environment. The selection of long cable lengths
for a given implementation, requires significant
compensation which will over-compensate for shorter, less
attenuating lengths. Conversely, the selection of short or
intermediate cable lengths requiring less compensation will
cause serious under-compensation for longer length
cables. Therefore, the compensation or equalization must
be adaptive to ensure proper conditioning of the received
signal independent of the cable length.
Subject to change without notice.
The curves given in Figure 3-10 illustrate attenuation at
certain frequencies for given cable lengths. This is derived
from the worst case frequency vs. attenuation figures as
specified in the EIA/TIA Bulletin TSB-36. These curves
indicate the significant variations in signal attenuation that
must be compensated for by the receive adaptive
equalization circuit.
25
Rev O
www.national.com
DP83815
te
3.0 Functional Description (Continued)
2ns/div
ol
e
Figure 3-12 MLT-3 Signal Measured at AII after 50
meters of CAT V cable
O
bs
Figure 3-10 EIA/TIA Attenuation vs. Frequency for 0, 50,
100, 130 & 150 meters of CAT V cable
2ns/div
2ns/div
Figure 3-11 MLT-3 Signal Measured at AII after 0 meters
of CAT V cable
Figure 3-13 MLT-3 Signal Measured at AII after 100
meters of CAT V cable
3.10.4 Line Quality Monitor
It is possible to determine the amount of Equalization being
used by accessing certain test registers with the DSP
engine. This provides a crude indication of connected
cable length. This function allows for a quick and simple
verification of the line quality in that any significant
deviation from an expected register value (based on a
known cable length) would indicate that the signal quality
has deviated from the expected nominal case.
Subject to change without notice.
3.10.5 MLT-3 to NRZI Decoder
The DP83815 decodes the MLT-3 information from the
Digital Adaptive Equalizer block to binary NRZI data.
26
Rev O
www.national.com
recognize sufficient unscrambled IDLE code-groups within
the 722 µs period, the entire de-scrambler will be forced
out of the current state of synchronization and reset in
order to re-acquire synchronization.
3.10.6 Clock Recovery Module
The Clock Recovery Module (CRM) accepts 125 Mb/s
MLT3 data from the equalizer. The DPLL locks onto the
125 Mb/s data stream and extracts a 125 MHz recovered
clock. The extracted and synchronized clock and data are
used as required by the synchronous receive operations as
generally depicted in Figure 3-8.
3.10.10 Code-group Alignment
The CRM is implemented using an advanced all digital
Phase Locked Loop (PLL) architecture that replaces
sensitive analog circuitry. Using digital PLL circuitry allows
the DP83815 to be manufactured and specified to tighter
tolerances.
The code-group alignment module operates on unaligned
5-bit data from the de-scrambler (or, if the de-scrambler is
bypassed, directly from the NRZI/NRZ decoder) and
converts it into 5B code-group data (5 bits). Code-group
alignment occurs after the J/K code-group pair is detected.
Once the J/K code-group pair (11000 10001) is detected,
subsequent data is aligned on a fixed boundary.
3.10.7 NRZI to NRZ
3.10.11 4B/5B Decoder
ol
e
te
The code-group decoder functions as a look up table that
translates incoming 5B code-groups into 4B nibbles. The
code-group decoder first detects the J/K code-group pair
preceded by IDLE code-groups and replaces the J/K with
MAC preamble. Specifically, the J/K 10-bit code-group pair
is replaced by the nibble pair (0101 0101). All subsequent
3.10.8 Serial to Parallel
5B code-groups are converted to the corresponding 4B
The 100BASE-TX receiver includes a Serial to Parallel nibbles for the duration of the entire packet. This
converter which supplies 5-bit wide data symbols to the conversion ceases upon the detection of the T/R codePCS Rx state machine.
group pair denoting the End of Stream Delimiter (ESD) or
with the reception of a minimum of two IDLE code-groups.
3.10.9 De-scrambler
In a typical application, the NRZI to NRZ decoder is
required in order to present NRZ formatted data to the descrambler (or to the code-group alignment block, if the descrambler is bypassed, or directly to the PCS, if the
receiver is bypassed).
A serial de-scrambler is used to de-scramble the received
NRZ data. The de-scrambler has to generate an identical
data scrambling sequence (N) in order to recover the
original unscrambled data (UD) from the scrambled data
(SD) as represented in the equations:
SD = ( UD ⊕ N )
UD = ( SD ⊕ N )
bs
Synchronization of the de-scrambler to the original
scrambling sequence (N) is achieved based on the
knowledge that the incoming scrambled data stream
consists of scrambled IDLE data. After the de-scrambler
has recognized 12 consecutive IDLE code-groups, where
an unscrambled IDLE code-group in 5B NRZ is equal to
five consecutive ones (11111), it will synchronize to the
receive data stream and generate unscrambled data in the
form of unaligned 5B code-groups.
O
In order to maintain synchronization, the de-scrambler
must continuously monitor the validity of the unscrambled
data that it generates. To ensure this, a line state monitor
and a hold timer are used to constantly monitor the
synchronization status. Upon synchronization of the descrambler the hold timer starts a 722 µs countdown. Upon
detection of sufficient IDLE code-groups (58 bit times)
within the 722 µs period, the hold timer will reset and begin
a new countdown. This monitoring operation will continue
indefinitely given a properly operating network connection
with good signal integrity. If the line state monitor does not
Subject to change without notice.
3.10.12 100BASE-TX Link Integrity Monitor
The 100 Base-TX Link monitor ensures that a valid and
stable link is established before enabling both the Transmit
and Receive PCS layer.
Signal detect must be valid for 395 µs to allow the link
monitor to enter the 'Link Up' state, and enable the transmit
and receive functions.
Signal detect can be forced active by setting Bit 1 of the
PCSR.
Signal detect can be optionally ANDed with the descrambler locked indication by setting bit 8 of the PCSR.
When this option is enabled, then De-scrambler 'locked' is
required to enter the Link Up state, but only Signal detect is
required to maintain the link in the link Up state.
3.10.13 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition
from consecutive idle code-groups to non-idle code-groups
which is not prefixed by the code-group pair J/K.
If this condition is detected, the DP83815 will assert RXER
and present RXD[3:0] = 1110 to the MAC for the cycles that
correspond to received 5B code-groups until at least two
IDLE code groups are detected. In addition, the False
Carrier Event Counter will be incremented by one.
Once at least two IDLE code groups are detected, the error
is reported to the MAC.
27
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
3.11 10BASE-T Transceiver Module
The squelch circuitry employs a combination of amplitude
and timing measurements (as specified in the IEEE 802.3
The 10BASE-T Transceiver Module is IEEE 802.3
10BASE-T standard) to determine the validity of data on
compliant. It includes the receiver, transmitter, collision,
the twisted pair inputs (refer to Figure 3-14).
heartbeat, loopback, jabber, and link integrity functions, as
defined in the standard. An external filter is not required on The signal at the start of packet is checked by the smart
the 10BASE-T interface since this is integrated inside the squelch and any pulses not exceeding the squelch level
DP83815. This section focuses on the general 10BASE-T (either positive or negative, depending upon polarity) will
be rejected. Once this first squelch level is overcome
system level operation.
correctly, the opposite squelch level must then be
3.11.1 Operational Modes
exceeded within 150 ns. Finally the signal must again
The DP83815 has two basic 10BASE-T operational exceed the original squelch level within a 150 ns to ensure
modes:
that the input waveform will not be rejected. This checking
— Half Duplex mode - functions as a standard IEEE 802.3 procedure results in the loss of typically three preamble bits
at the beginning of each packet.
10BASE-T transceiver supporting the CSMA/CD
protocol.
— Full Duplex mode - capable of simultaneously
transmitting and receiving without reporting a collision.
The DP83815's 10 Mb/s ENDEC is designed to encode
and decode simultaneously.
3.11.2 Smart Squelch
Valid data is considered to be present until the squelch
level has not been generated for a time longer than 150 ns,
indicating the End of Packet. Once good data has been
detected the squelch levels are reduced to minimize the
effect of noise causing premature End of Packet detection.
ol
e
The smart squelch is responsible for determining when
valid data is present on the differential receive inputs
(RD±). The DP83815 implements an intelligent receive
squelch to ensure that impulse noise on the receive inputs
will not be mistaken for a valid signal. Smart squelch
operation is independent of the 10BASE-T operational
mode.
te
Only after all these conditions have been satisfied will a
control signal be generated to indicate to the remainder of
the circuitry that valid data is present. At this time, the
smart squelch circuitry is reset.
<150 ns
>150 ns
<150 ns
VSQ+
bs
VSQ+(reduced)
VSQ-(reduced)
VSQ-
end of packet
start of packet
O
Figure 3-14 10BASE-T Twisted Pair Smart Squelch Operation
3.11.4 Normal Link Pulse Detection/Generation
3.11.3 Collision Detection
When in Half Duplex, a 10BASE-T collision
when the receive and transmit channels
simultaneously. Collisions are reported to
Collisions are also reported when a jabber
detected.
is detected
are active
the MAC.
condition is
The link pulse generator produces pulses as defined in the
IEEE 802.3 10BASE-T standard. Each link pulse is
nominally 100 ns in duration and transmitted every 16 ms
in the absence of transmit data.
Link pulses are used to check the integrity of the
connection with the remote end. If valid link pulses are not
received, the link detector disables the 10BASE-T twisted
When heartbeat is enabled, approximately 1 µs after the pair transmitter, receiver and collision detection functions.
the
link
integrity
function
is
disabled
transmission of each packet, a Signal Quality Error (SQE) When
signal of approximately 10 bit times is generated to indicate (FORCE_LINK_10 of the TBTSCR register), good link is
forced and the 10BASE-T transceiver will operate
successful transmission.
The SQE test is inhibited when the physical layer is set in regardless of the presence of link pulses.
If the ENDEC is receiving when a collision is detected it is
reported immediately (through the COL signal).
full duplex mode. SQE can also be inhibited by setting the
HEARTBEAT_DIS bit in the TBTSCR register.
Subject to change without notice.
28
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
clock signals and data. The differential input must be
externally terminated with a differential 100Ω termination
network to accommodate UTP cable. The internal
impedance of RD± (typically 1.1Kohms) is in parallel with
two 54.9 resistors to approximate the 100Ω termination.
3.11.5 Jabber Function
The jabber function monitors the DP83815's output and
disables the transmitter if it attempts to transmit a packet of
longer than legal size. A jabber timer monitors the
transmitter and disables the transmission if the transmitter
is active for approximately 20-30 ms.
The decoder detects the end of a frame when no more midbit transitions are detected.
Once disabled by the jabber function, the transmitter stays
disabled for the entire time that the ENDEC module's
internal transmit enable is asserted. This signal has to be
de-asserted for approximately 400-600 ms (the “unjab”
time) before the jabber function re-enables the transmit
outputs.
3.11.11 Far End Fault Indication
Auto-Negotiation provides a mechanism for transferring
information from the Local Station to the Link Partner that a
remote fault has occurred for 100BASE-TX.
A remote fault is an error in the link that one station can
detect while the other cannot. An example of this is a
disconnected fiber at a station’s transmitter. This station will
be receiving valid data and detect that the link is good via
the Link Integrity Monitor, but will not be able to detect that
its transmission is not propagating to the other station.
The Jabber function is only meaningful in 10BASE-T mode.
3.11.6 Automatic Link Polarity Detection
bs
ol
e
te
The
DP83815's
10BASE-T
transceiver
module
incorporates an automatic link polarity detection circuit.
When seven consecutive link pulses or three consecutive
receive packets with inverted End-of-Packet pulses are If three or more FEFI IDLE patterns are detected by the
DP83815, then bit 4 of the Basic Mode Status register is
received, bad polarity is reported.
set to one until read by management, additionally bit 7 of
A polarity reversal can be caused by a wiring error at either
the PHY Status register is also set.
end of the cable, usually at the Main Distribution Frame
The first FEFI IDLE pattern may contain more than 84 ones
(MDF) or patch panel in the wiring closet.
as the pattern may have started during a normal IDLE
The bad polarity condition is latched. The DP83815's
transmission which is actually quite likely to occur.
10BASE-T transceiver module corrects for this error
However, since FEFI is a repeating pattern, this will not
internally and will continue to decode received data
cause a problem with the FEFI function. It should be noted
correctly. This eliminates the need to correct the wiring
that receipt of the FEFI IDLE pattern will not cause a
error immediately.
Carrier Sense error to be reported.
3.11.7 10BASE-T Internal Loopback
If the FEFI function has been disabled via FEFI_EN (bit 3)
When the LOOPBACK bit in the BMCR register is set, of the PCSR Configuration register, then the DP83815 will
10BASE-T transmit data is looped back in the ENDEC to not send the FEFI IDLE pattern.
the receive channel. The transmit drivers and receive input
circuitry are disabled in transceiver loopback mode, 3.12 802.3u MII
isolating the transceiver from the network.
The DP83815 incorporates the Media Independent
Loopback is used for diagnostic testing of the data path Interface (MII) as specified in Clause 22 of the IEEE 802.3u
through the transceiver without transmitting on the network standard. This interface may be used to connect PHY
or being interrupted by receive traffic. This loopback devices. This section describes the MII configuration steps
function causes the data to loopback just prior to the as well as the serial MII management interface and nibble
10BASE-T output driver buffers such that the entire wide MII data interface.
transceiver path is tested.
3.12.1 MII Access Configuration
3.11.8 Transmit and Receive Filtering
The DP83815 must be specifically configured for
accessing the MII. This is done by first connecting pin 133
(MD1/CFGDISN) to GND through a 1KΩ resistor. Then
setting bit 12 (EXT_PHY) of the CFG register (offset 04h)
to 1. See Section 4.2.2. When this bit is set, the internal
Phy is automatically disabled, as reported by bit 9
(PHY_DIS) of the CFG register. The MII must then be reset
before the external PHY can be detected.
O
External 10BASE-T filters are not required when using the
DP83815, as the required signal conditioning is integrated
into the device.
Only isolation/step-up transformers and impedance
matching resistors are required for the 10BASE-T transmit
and receive interface. The internal transmit filtering
ensures that all the harmonics in the transmit signal are
attenuated by at least 30 dB.
3.11.9 Transmitter
The encoder begins operation when the transmit enable
input to the physical layer is asserted and converts NRZ
data to pre-emphasized Manchester data for the
transceiver. For the duration of assertion, the serialized
transmit data is encoded for the transmit-driver pair (TD±).
The last transition is always positive; it occurs at the center
of the bit cell if the last bit is a one, or at the end of the bit
cell if the last bit is a zero.
3.11.10 Receiver
The decoder consists of a differential receiver and a PLL to
separate a Manchester encoded data stream into internal
Subject to change without notice.
If external MII is not selected as described then the internal
Phy is used and the MII pins of the MacPhyter can be left
unconnected.
3.12.2 MII Serial Management
The MII serial management interface allows for the
configuration and control of PHY registers, gathering of
status, error information, and the determination of the type
and capabilities of the attached PHY(s).
The MII serial management specification defines a set of
thirty-two 16-bit status and control registers that are
accessible through the management interface pins MDC
and MDIO. A description of the serial management
interface access and access protocol follows.
29
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
3.12.3 MII Serial Management Access
3.12.4 Serial Management Access Protocol
Management access to the PHY(s) is done via
Management Data Clock (MDC) and Management Data
Input/Output (MDIO). MDC has a maximum clock rate of 25
MHz and no minimum rate. The MDIO line is bi-directional
and may be shared by up to 32 devices. The internal PHY
counts as one of these 32 devices.
The serial control interface clock (MDC) has a maximum
clock rate of 25 MHz and no minimum rate. The MDIO line
is bi-directional and may be shared by up to 32 devices.
The MDIO frame format is shown in Table 3-2.
ol
e
te
If external PHY devices may be attached and removed
from the MII there should be a 15 KΩ pull-down resistor on
The internal PHY has the advantage of having direct the MDIO signal. If the PHY will always be connected then
register access but can also be controlled exactly like a there should be a 1.5 kΩ pull-up resistor which, during
IDLE and turnaround, will pull MDIO high. In order to
PHY, with a default address of 1Fh, connected to the MII.
Access and control of the MDC and MDIO pins is done via initialize the MDIO interface, the DP83815 sends a
the MII/EEPROM Access Register (MEAR). The clock sequence of 32 contiguous logic ones on MDIO provides
(MDC) is created by alternating writes of 0 then 1 to the the PHY(s) with a sequence that can be used to establish
MDC bit (bit 6). Control of data direction is done by the synchronization. This preamble may be generated either
MDDIR bit (bit 5). Data is either recorded or written by the by driving MDIO high for 32 consecutive MDC clock cycles,
MDIO bit (bit 4). Setting the MDDIR bit to a 1 allows the or by simply allowing the MDIO pull-up resistor to pull the
DP83815 to drive the MDIO pin. Setting the MDDIR bit to a MDIO pin high during which time 32 MDC clock cycles are
0 allows the MDIO bit to reflect the value of the MDIO pin. provided. In addition 32 MDC clock cycles should be used
to re-sync the device if an invalid start, opcode, or
See Section 4.2.3
turnaround bit is detected.
This bit-bang access of the MDC and MDIO pins thus
requires 64 accesses to the MEAR register to complete a
single PHY register transaction. Since a PHY device is
typically self configuring and adaptive this serial
management access is usually only required at
initialization time and therefore is not time critical.
Table 3-2 Typical MDIO Frame Format
MII Management
Serial Protocol
<idle><start><op code><device addr><reg addr><turnaround><data><idle>
Read Operation
<idle><01><10><AAAAA><RRRRR><Z0><xxxx xxxx xxxx xxxx><idle>
Write Operation
<idle><01><01><AAAAA><RRRRR><10><xxxx xxxx xxxx xxxx><idle>
bs
The Start code is indicated by a <01> pattern. This assures
the MDIO line transitions from the default idle line state.
Turnaround is defined as an idle bit time inserted between
the Register Address field and the Data field. To avoid
contention during a read transaction, no device shall
actively drive the MDIO signal during the first bit of
Turnaround. The addressed PHY drives the MDIO with a
zero for the second bit of turnaround and follows this with
the required data. Figure 3-15 shows the timing
relationship between MDC and the MDIO as
driven/received by the DP83815 and a PHY for a typical
register read access.
O
MDC
MDIO
Z
Z
(STA)
Z
MDIO
Z
(PHY)
Z
Idle
0 1 1 0 0 1 1 0 0 0 0 0 0 0
Start
Opcode
(Read)
PHY Address
(PHYAD = 0Ch)
Z
Register Address
(00h = BMCR)
0 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0
Idle
Register Data
TA
Z
Figure 3-15 Typical MDC/MDIO Read Operation
For write transactions, the DP83815 writes data to the
addressed PHY thus eliminating the requirement for MDIO
Turnaround. The Turnaround time is filled by the DP83815
by inserting <10>. Figure 3-16 shows the timing
relationship for a typical MII register write access.
Subject to change without notice.
3.12.5 Nibble-wide MII Data Interface
Clause 22 of the IEEE 802.3u specification defines the
Media Independent Interface. This interface include
separate dedicated receive and transmit busses. These
two data buses, along with various control and indication
signals, allow for the simultaneous exchange of data
between the DP83815 and PHY(s).
30
Rev O
www.national.com
DP83815
3.0 Functional Description (Continued)
DP83815
3.0 Functional Description (Continued)
MDC
MDIO
Z
Z
(STA)
Z
Idle
0 1 0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Start
Opcode
(Write)
PHY Address
(PHYAD = 0Ch)
Register Address
(00h = BMCR)
TA
Z
Idle
Register Data
Figure 3-16 Typical MDC/MDIO Write Operation
The transmit interface consists of a nibble wide data bus
TXD[3:0], a transmit enable control signal TXEN, and a
transmit clock TXCLK which runs at 2.5 MHz or 25 MHz.
have been received while in the collision state. This
prevents a collision being reported incorrectly due to noise
on the network. The COL signal remains set for the
duration of the collision.
If a collision occurs during a receive operation, it is
immediately reported by the COL signal.
te
The receive interface consists of a nibble wide data bus
RXD[3:0], a receive error signal RXER, a receive data valid
flag RXDV, and a receive clock RXCLK for synchronous
transfer of the data. The receive clock can operate at 2.5
MHz to support 10 Mb/s operation modes or at 25 MHz to
support 100 Mb/s operational modes.
When heartbeat is enabled (only applicable to 10 Mb/s
operation), approximately 1µs after the transmission of
each packet, a Signal Quality Error (SQE) signal of
approximately 10 bit times is generated (internally) to
indicate successful transmission. SQE is reported as a
pulse on the COL signal of the MII.
O
bs
ol
e
Additionally, the MII includes the carrier sense signal CRS,
as well as a collision detect signal COL. The CRS signal
asserts to indicate the reception of data from the network
or as a function of transmit data in Half Duplex mode. The 3.12.7 Carrier Sense
COL signal asserts as an indication of a collision which can
occur during half-duplex operation when both a transmit Carrier Sense (CRS) is asserted due to receive activity,
once valid data is detected, during 10 Mb/s operation.
and receive operation occur simultaneously.
During 100 Mb/s operation CRS is asserted when a valid
3.12.6 Collision Detection
link (SD) and two non-contiguous zeros are detected.
For Half Duplex, a 10BASE-T or 100BASE-TX collision is For 10 or 100 Mb/s Half Duplex operation, CRS is asserted
detected when the receive and transmit channels are during either packet transmission or reception.
active simultaneously. Collisions are reported by the COL
For 10 or 100 Mb/s Full Duplex operation, CRS is asserted
signal on the MII.
only due to receive activity.
If the PHY is transmitting in 10 Mb/s mode when a collision
is detected, the collision is not reported until seven bits CRS is de-asserted following an end of packet.
Subject to change without notice.
31
Rev O
www.national.com
4.1 Configuration Registers
The DP83815 implements a PCI version 2.2 configuration register space. This allows a PCI BIOS to "soft" configure the
DP83815. Software Reset has no effect on configuration registers. Hardware Reset returns all configuration registers to
their hardware reset state. For all unused registers, writes are ignored, and reads return 0.
Table 4-1 Configuration Register Map
Tag
00h
CFGID
Configuration Identification Register
RO
04h
CFGCS
Configuration Command and Status Register
R/W
08h
CFGRID
Configuration Revision ID Register
RO
0Ch
CFGLAT
Configuration Latency Timer Register
RO
10h
CFGIOA
Configuration IO Base Address Register
R/W
14h
CFGMA
Configuration Memory Address Register
R/W
18h-28h
Description
Access
te
Offset
Reserved (reads return zero)
2Ch
CFGSID
Configuration Subsystem Identification Register
RO
30h
CFGROM Boot ROM configuration register
R/W
34h
CAPPTR
RO
Capabilities Pointer Register
Reserved (reads return zero)
3Ch
40h
44h
CFGINT
Configuration Interrupt Select Register
R/W
PMCAP
Power Management Capabilities Register
RO
PMCSR
Power Management Control and Status Register
R/W
Reserved (reads return zero)
bs
48-FFh
ol
e
38h
4.1.1 Configuration Identification Register
This register identifies the DP83815 Controller to PCI system software.
Tag: CFGID
Hard Reset: 0020100Bh
Access: Read Only
Soft Reset: Unchanged
O
Offset: 00h
Size: 32 bits
Bit
Bit Name
31-16
DEVID
Description
Device ID
This field is read-only and is set to the device ID assigned by National Semiconductor to the DP83815,
which is 0020h.
15-0
VENID
Vendor ID
This field is read-only and is set to a value of 100Bh which is National Semiconductor's PCI Vendor ID.
32
www.national.com
DP83815
4.0 Register Set
4.1.2 Configuration Command and Status Register
The CFGCS register has two parts. The upper 16-bits (31-16) are devoted to device status. A status bit is reset whenever
the register is written, and the corresponding bit location is a 1. The lower 16-bits (15-0) are devoted to command and are
used to configure and control the device.
Tag: CFGCS
Offset: 04h
Bit
Bit Name
31
DPERR
Size: 32 bits
Access: Read Write
Hard Reset: 02900000h
Soft Reset: Unchanged
Description
Detected Parity Error
Refer to the description in the PCI V2.2 specification.
30
SSERR
Signaled SERR
29
RMABT
Received Master Abort
te
Refer to the description in the PCI V2.2 specification.
Refer to the description in the PCI V2.2 specification.
28
RTABT
Received Target Abort
Refer to the description in the PCI V2.2 specification.
27
STABT
Sent Target Abort
26-25
DSTIM
ol
e
Refer to the description in the PCI V2.2 specification.
DEVSELN Timing
This field will always be set to 01 indicating that DP83815 supports “medium” DEVSELN timing.
24
DPD
Data Parity Detected
Refer to the description in the PCI V2.2 specification.
23
FBB
Fast Back-to-Back Capable
DP83815 will set this bit to 1.
22-21
unused
20
bs
(reads return 0)
NCPEN
New Capabilities Enable
When set, this bit indicates that the Capabilities Pointer contains a valid value and new capabilities such
as power management are supported. When clear, new capabilities (CAPPTR, PMCAP, PMCS) are
disabled. The value in this register will either be loaded from the EEPROM or, if the EEPROM is
disabled, from a strap option at reset.
19-16
Unused
O
(reads return 0)
15-10
Unused
(reads return 0)
9
FBBEN
Fast Back-to-Back Enable
Set to 1 by the PCI BIOS to enable the DP83815 to do Fast Back-to-Back transfers (FBB transfers as a
master is not implemented in the current revision).
8
SERREN
SERRN Enable
When SERREN and PERRSP are set, DP83815 will generate SERRN during target cycles when an
address parity error is detected from the system. Also, when SERREN and PERRSP are set and
CFG:PESEL is reset, master cycles detecting data parity errors will generate SERRN.
7
Unused
(reads return 0)
33
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
6
PERRSP
Description
Parity Error Response
When set, DP83815 will assert PERRN on the detection of a data parity error when acting as the target,
and will sample PERRN when acting as the initiator. Also, setting PERRSP allows SERREN to enable
the assertion of SERRN. When reset, all address and data parity errors are ignored and neither SERRN
nor PERRN are asserted.
5-3
Unused
(reads return 0)
2
BMEN
Bus Master Enable
When set, DP83815 is allowed to act as a PCI bus master. When reset, DP83815 is prohibited from
acting as a PCI bus master.
1
MSEN
Memory Space Address
0
I/OSEN
I/O Space Access
te
When set, DP83815 responds to memory space accesses. When reset, DP83815 ignores memory
space accesses.
When set, DP83815 responds to I/O space accesses. When reset, DP83815 ignores I/O space
accesses.
ol
e
4.1.3 Configuration Revision ID Register
This register stores the silicon revision number, revision number of software interface specification and lets the
configuration software know that it is an Ethernet controller in the class of network controllers.
Tag: CFGRID
Offset: 08h
Bit Name
31-24
BASECL
Hard Reset: 02000000h
Access: Read Only
Soft Reset: Unchanged
Description
Base Class
bs
Bit
Size: 32 bits
Returns 02h which specifies a network controller.
23-16
SUBCL
Sub Class
Returns 00h which specifies an Ethernet controller.
15-8
PROGIF
Programming IF
Returns 00h which specifies the first release of the DP83815 Software Interface Specification.
REVID
Silicon Revision
O
7-0
Returns 00h which specifies the silicon revision.
34
www.national.com
4.1.4 Configuration Latency Timer Register
This register gives status and controls such miscellaneous functions as BIST, Latency timer and Cache line size.
Tag: CFGLAT
Offset: 0Ch
Bit
Bit Name
31
BISTCAP
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: Unchanged
Description
BIST Capable
Reads will always return 0.
30
BISTEN
BIST Enable
Reads will return a 0, writes are ignored.
29-16
Reserved
15-8
LAT
Latency Timer
te
Reads will return a 0, writes are ignored.
Set by software to the number of PCI clocks that DP83815 may hold the PCI bus.
7-0
CLS
Cache Line Size
ol
e
Ignored by DP83815.
DP83815 Bus Master Operations:
Independent of cache line size, the DP83815 will use the following PCI commands for bus mastered transfers:
0110 - Mem Read
for all read cycles,
0111 - Mem Write
for all write cycles.
bs
4.1.5 Configuration I/O Base Address Register
This register specifies the Base I/O address which is required to build an address map during configuration. It also
specifies the number of bytes required as well as an indication that it can be mapped into I/O space.
Tag: CFGIOA
Size: 32 bits
Access: Read Write
O
Offset: 10h
Bit
Bit Name
31-8
IOBASE
Hard Reset: 00000001h
Soft Reset: Unchanged
Description
Base I/O Address
This is set by software to the base I/O address for the Operational Register Map.
7-2
IOSIZE
Size indication
Read back as 0. This allows the PCI bridge to determine that the DP83815 requires 256 bytes of I/O
space.
1
Unused
(reads return 0).
0
IOIND
I/O Space Indicator
Set to 1 by DP83815 to indicate that DP83815 is capable of being mapped into I/O space. Read Only.
35
www.national.com
DP83815
4.0 Register Set (Continued)
4.1.6 Configuration Memory Address Register
This register specifies the Base Memory address which is required to build an address map during configuration. It also
specifies the number of bytes required as well as an indication that it can be mapped into memory space.
Tag: CFGMA
Offset: 14h
Bit
Bit Name
31-12
MEMBASE
11-4
MEMSIZE
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: unchanged
Description
Memory Base Address
This is set by software to the base address for the Operational Register Map.
Memory Size
3
MEMPF
Prefetchable
Set to 0 by DP83815. Read Only.
2-1
MEMLOC
Location Selection
te
These bits return 0, which indicates that the DP83815 requires 4096 bytes of Memory Space (the
minimum recommended allocation).
Set to 00 by DP83815. This indicates that the base register is 32-bits wide and can be placed anywhere
in the 32-bit memory space. Read Only.
MEMIND
Memory Space Indicator
ol
e
0
Set to 0 by DP83815 to indicate that DP83815 is capable of being mapped into memory space. Read
Only.
4.1.7 Configuration Subsystem Identification Register
The CFGSID allows system software to distinguish between different subsystems based on the same PCI silicon. The
values in this register can be loaded from the EEPROM if configuration is enabled.
Offset: 2Ch
Bit
Size: 32 bits
Hard Reset: 00000000h
Access: Read Only
Soft Reset: unchanged
bs
Tag: CFGSID
31-16
Bit Name
SDEVID
Description
Subsystem Device ID
O
Set to 0 by DP83815.
15-0
SVENID
Subsystem Vendor ID
Set to 0 by DP83815.
36
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
4.1.8 Boot ROM Configuration Register
Tag: CFGROM
Offset: 30h
Bit
Bit Name
31-16
ROMBASE
15-11
ROMSIZE
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: unchanged
Description
ROM Base Address
Set to the base address for the boot ROM.
ROM Size
Set to 0 indicating a requirement for 64K bytes of Boot ROM space. Read only.
10-1
unused
(reads return 0)
ROMEN
ROM Enable
te
0
ol
e
This is used by the PCI BIOS to enable accesses to boot ROM. This allows the DP83815 to share the
address decode logic between the boot ROM and itself. The BIOS will copy the contents of the boot
ROM to system RAM before executing it. Set to 1 enables the address decode for boot ROM disabling
access to operational target registers.
4.1.9 Capabilities Pointer Register
This register stores the capabilities linked list offset into the PCI configuration space.
Tag: CAPPTR
Offset: 34h
31-8
Bit Name
Hard Reset: 00000040h
Access: Read Only
Soft Reset: unchanged
Description
bs
Bit
Size: 32 bits
unused
(reads return 0)
7-0
CLOFS
Capabilities List Offset
O
Offset into PCI configuration space for the location of the first item in the Capabilities Linked List, set to
40h to point to the PMCAP register.
37
www.national.com
4.1.10 Configuration Interrupt Select Register
This register stores the interrupt line number as identified by the POST software that is connected to the interrupt
controller as well as DP83815 desired settings for maximum latency and minimum grant. Max latency and Min latency
can be loaded from the EEPROM.
Tag: CFGINT
Offset: 3Ch
Bit
Bit Name
31-24
MXLAT
Size: 32 bits
Access: Read Write
Hard Reset: 340b0100h
Soft Reset: unchanged
Description
Maximum Latency
The DP83815 desired setting for Max Latency. The DP83815 will initialize this field to 52d (13 µsec). The
value in this register can be loaded from the EEPROM.
23-16
MNGNT
Minimum Grant
15-8
IPIN
Interrupt Pin
te
The DP83815 desired setting for Minimum Grant. The DP83815 will initialize this field to 11d (2.75 usec).
The value in this register can be loaded from the EEPROM.
Read Only, always return 0000 0001 (INTA).
7-0
ILINE
Interrupt Line
ol
e
Set to which line on the interrupt controller that the DP83815's interrupt pin is connected to.
4.1.11 Power Management Capabilities Register
This register provides information on the capabilities of the functions related to power management. This register also
contains a pointer to the next item in the capabilities list and the capability ID for Power Management. This register is only
visible if CFGCS[4] is set.
Tag: PMCAP
Bit
Access: Read Only
bs
Offset: 40h
Size: 32 bits
31-27
Bit Name
PMES
Hard Reset: FF820001
Soft Reset: unchanged
Description
PME Support
O
This 5 bit field indicates the power states in which DP83815 may assert PMEN. A 1 indicates PMEN
is enabled for that state, a 0 indicates PMEN is inhibited in that state.
XXXX1 - PMEN can be asserted from state D0
XXX1X - PMEN can be asserted from state D1
XX1XX - PMEN can be asserted from state D2
X1XXX - PMEN can be asserted from state D3hot
1XXXX - PMEN can be asserted from state D3cold
The DP83815 will only report PME support for D3cold if auxiliary power is detected on the 3VAUX
pin, in addition this value can be loaded from the EEPROM when in the D3cold state.
26
D2S
25
D1S
D2 Support
This bit is set to a 1 when the DP83815 supports the D2 state.
D1 Support
This bit is set to a 1 when the DP83815 supports the D1 state.
38
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
24-22
Description
AUX_CURRENT Aux_Current
This 3 bit field reports the 3.3Vaux auxiliary current requirements for the PCI function.
If PMEN generation from D3cold is not supported by the function(PMCAP[31]), this field returns a
value of "000b" when read.
21
DSI
Bit
3.3Vaux
24 23 22
Max. Current Required
110
320 mA
000
0 (self powered)
Device Specific Initialization
20
Reserved
(reads return 0)
19
PMEC
PME Clock
te
This bit is set to 1 to indicate to the system that initialization of the DP83815 device is required
(beyond the standard PCI configuration header) before the generic class device driver is able to use
it. A 1 indicates that DP83815 requires a DSI sequence following transition to the D0 uninitialized
state. This bit can be loaded from the EEPROM.
Returns 0 to indicate PCI clock not needed for PMEN.
18-16
PMV
Power Management Version
15-8
NLIPTR
ol
e
This bit field indicates compliance to a specific PM specification rev level. Currently set to 010b.
Next List Item Pointer
Offset into PCI configuration space for the location of the next item in the Capabilities Linked List.
Returns 00h as no other capabilities are offered.
7-0
CAPID
Capability ID
Always returns 01h for Power Management ID.
4.1.12 Power Management Control and Status Register
bs
This register contains PM control and status information.
Tag: PMCSR
Offset: 44h
Bit
Size: 32 bits
Access: Read Write
Bit Name
Soft Reset: unchanged
Description
Reserved
(reads return 0)
O
31-24
Hard Reset: 00000000h
23-16
BSE
15
PMESTS
Bridge Support Extensions
unused (reads return 0)
PME Status
Sticky bit which represents the state of the PME logic, regardless of the state of the PMEEN bit.
14-9
8
Reserved
(reads return 0)
PMEEN
PME Enable
When set to 1, this bit enables the assertion of the PME function on the PMEN pin. When 0, the PMEN
pin is forced to be inactive. This value can be loaded from the EEPROM.
7-2
1-0
Unused
(reads return 0)
PSTATE
Power State
This 2 bit field is used to determine the current power state of DP83815, and to set a new power state.
00 - D0
10 - D2
01 - D1
11 - D3hot/cold
39
www.national.com
4.2 Operational Registers
The DP83815 provides the following set of operational registers mapped into PCI memory space or I/O space. Writes to
reserved register locations are ignored. Reads to reserved register locations return undefined values.
Table 4-2 Operational Register Map
Offset
Tag
Description
Access
MAC/BIU Registers
00h
CR
04h
CFG
Command Register
R/W
Configuration Register
08h
R/W
MEAR
EEPROM Access Register
R/W
0Ch
PTSCR
PCI Test Control Register
R/W
10h
ISR
Interrupt Status Register
RO
14h
IMR
Interrupt Mask Register
R/W
18h
IER
Interrupt Enable Register
R/W
Reserved
20h
TXDP
24h
TXCFG
28-2Ch
RXDP
34h
RXCFG
3Ch
40h
44h
48h
4Ch
50h
54h
58h
5Ch
R/W
Receive Descriptor Pointer Register
R/W
Receive Configuration Register
R/W
Reserved
CCSR
CLKRUN Control/Status Register
R/W
WCSR
Wake on LAN Control/Status Register
R/W
Pause Control/Status Register
R/W
RFCR
Receive Filter/Match Control Register
R/W
RFDR
Receive Filter/Match Data Register
R/W
BRAR
Boot ROM Address
R/W
BRDR
Boot ROM Data
R/W
PCR
SRR
MIBC
MIB
Silicon Revision Register
RO
Management Information Base Control Register
R/W
Management Information Base Data Registers
RO
bs
60-78h
R/W
Transmit Configuration Register
ol
e
38
Transmit Descriptor Pointer Register
Reserved
30h
te
1Ch
7Ch
Reserved
Internal Phy Registers
BMCR
Basic Mode Control Register
R/W
84h
BMSR
Basic Mode Status Register
RO
88h
PHYIDR1
PHY Identifier Register #1
RO
8Ch
PHYIDR2
PHY Identifier Register #2
RO
90h
ANAR
Auto-Negotiation Advertisement Register
R/W
94h
ANLPAR
Auto-Negotiation Link Partner Ability Register
R/W
98h
ANER
Auto-Negotiation Expansion Register
R/W
9Ch
ANNPTR
Auto-Negotiation Next Page TX
R/W
A0-BCh
Reserved
Reserved
C0h
PHYSTS
PHY Status Register
RO
C4h
MICR
MII Interrupt Control Register
RW
MII Interrupt Status Register
RW
O
80h
C8h
MISR
CCh
Reserved
D0h
FCSCR
False Carrier Sense Counter Register
R/W
D4h
RECR
Receive Error Counter Register
R/W
D8h
PCSR
100 Mb/s PCS Configuration and Status Register
R/W
DCh-E0h
Reserved
Reserved
Reserved
E4h
PHYCR
PHY Control Register
R/W
E8h
TBTSCR
10Base-T Status/Control Register
R/W
ECh-FCh
Reserved
Reserved
40
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.1 Command Register
This register is used for issuing commands to DP83815. These commands are issued by setting the corresponding bits
for the function. A global software reset along with individual reset and enable/disable for transmitter and receiver are
provided here.
Tag: CR
Offset: 0000h
Bit
Access: Read Write
Bit Name
31-9
8
Size: 32 bits
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
unused
RST
Reset
7
SWI
Software Interrupt
te
Set to 1 to force the DP83815 to a soft reset state which disables the transmitter and receiver,
reinitializes the FIFOs, and resets all affected registers to their soft reset state. This operation implies
both a TXR and a RXR. This bit will read back a 1 during the reset operation, and be cleared to 0 by the
hardware when the reset operation is complete. EEPROM configuration information is not loaded here.
Setting this bit to a 1 forces the DP83815 to generate a hardware interrupt. This interrupt is mask-able
via the IMR.
5
unused
RXR
Receiver Reset
ol
e
6
When set to a 1, this bit causes the current packet reception to be aborted, the receive data and status
FIFOs to be flushed, and the receive state machine to enter the idle state (RXE goes to 0). This is a
write-only bit and is always read back as 0.
4
TXR
Transmit Reset
When set to a 1, this bit causes the current transmission to be aborted, the transmit data and status
FIFOs to be flushed, and the transmit state machine to enter the idle state (TXE goes to 0). This is a
write-only bit and is always read back as 0.
3
RXD
Receiver Disable
2
bs
Disable the receive state machine after any current packets in progress. When this operation has been
completed the RXE bit will be cleared to 0. This is a write-only bit and is always read back as 0. The
driver should not set both RXD and RXE in the same write, the RXE will be ignored, and RXD will have
precedence.
RXE
Receiver Enable
When set to a 1, and the receive state machine is idle, then the receive machine becomes active. This bit
will read back as a 1 whenever the receive state machine is active. After initial power-up, software must
insure that the receiver has completely reset before setting this bit (See ISR:RXRCMP).
TXD
Transmit Disable
O
1
When set to a 1, halts the transmitter after the completion of the current packet. This is a write-only bit
and is always read back as 0. The driver should not set both TXD and TXE in the same write, the TXE
will be ignored, and TXD will have precedence.
0
TXE
Transmit Enable
When set to a 1, and the transmit state machine is idle, then the transmit state machine becomes active.
This bit will read back as a 1 whenever the transmit state machine is active. After initial power-up,
software must insure that the transmitter has completely reset before setting this bit (See ISR:TXRCMP).
41
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.2 Configuration and Media Status Register
This register allows configuration of a variety of device and phy options, and provides phy status information.
Tag: CFG
Size: 32 bits
Offset: 0004h
Bit
Bit Name
31
LNKSTS
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
Link Status
Link status of the internal phy. Asserted when link is good. RO
30
SPEED100
Speed 100 Mb/s
Speed 100 Mb/s indicator for internal phy. Asserted when speed is set or has negotiated to 100 Mb/s.
De-asserted when speed has been set or negotiated to 10 Mb/s. RO
29
FDUP
Full Duplex
28
POL
10 Mb/s Polarity Indication
te
Full Duplex indicator for internal phy. Asserted when duplex mode is set or has negotiated to FULL. Deasserted when duplex mode has been set or negotiated to HALF. RO
Twisted pair polarity indicator for internal phy. Asserted when operating and 10 Mb/s and the polarity has
been detected as reversed. De-asserted when polarity is normal or phy is operating at 100 Mb/s. RO
ANEG_DN
Auto-negotiation Done
ol
e
27
Auto-negotiation done indicator from internal phy. Asserted when auto-negotiation process has
completed or is not active. RO
26-24
23-18
unused
PHY_CFG
Phy Configuration
Miscellaneous internal phy Power-On-Reset configuration control bits.
17
PINT_ACEN Phy Interrupt Auto Clear Enable
16
bs
When set to a 1, this bit allows the phy interrupt source to be automatically cleared whenever the ISR is
read. When this bit is 0, the phy interrupt source must be manually cleared via access of the phy
registers. R/W
PAUSE_ADV Pause Advertise
This bit is loaded from EEPROM at power-up and is used to configure the internal phy to advertise the
capability of 802.3x pause during auto-negotiation. Setting this bit to 1 will cause the pause function to be
advertised if the phy has also been configured to advertise full duplex capability (See ANEG_SEL).
15-13
ANEG_SEL
Auto-negotiation Select
O
These bits are loaded from EEPROM at power-up and are used to define the default state of the internal
phy auto-negotiation logic. R/W These bits are encoded as follows:
12
EXT_PHY
000
Auto-negotiation disabled, force 10 Mb/s half duplex
010
Auto-negotiation disabled, force 100 Mb/s half duplex
100
Auto-negotiation disabled, force 10 Mb/s full duplex
110
Auto-negotiation disabled, force 100 Mb/s full duplex
001
Auto-negotiation enabled, advertise 10 Mb/s half & full duplex
011
Auto-negotiation enabled, advertise 10/100 Mb/s half duplex
101
Auto-negotiation enabled, advertise 100 Mb/s half & full duplex
111
Auto-negotiation enabled, advertise 10/100 Mb/s half & full duplex
External Phy Support
Act as a stand-alone MAC. When set, this bit enables the MII and disables the internal Phy (sets bit 9).
R/W
11
Reserved
42
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
10
PHY_RST
Description
Reset internal Phy
Asserts reset to internal phy. Can be used to cause phy to reload options from the CFG register. This bit
does not self clear when set. R/W
9
PHY_DIS
Disable internal Phy
When set to a 1, this bit forces the internal phy to its low-power state. R/W
8
EUPHCOMP DP83810 Descriptor Compatibility
When set, DP83815 will use DP83810 compatible (but single fragment) descriptor format. Descriptors
are four 32-bit words in length, but the fragment count field is ignored. When clear, DP83815 will only
fetch 3 32-bit words in descriptor fetches with the third word being the fragment pointer. R/W
7
REQALG
PCI Bus Request Algorithm
Selects mode for making requests for the PCI bus. When set to 0 (default), DP83815 will use an
aggressive Request scheme. When set to a 1, DP83815 will use a more conservative scheme. R/W
6
SB
Single Back-off
5
POW
Program Out of Window Timer
te
Setting this bit to 1 forces the transmitter back-off state machine to always back-off for a single 802.3 slot
time instead of following the 802.3 random back-off algorithm. A 0 (default) allows normal transmitter
back-off operation. R/W
4
EXD
ol
e
This bit controls when the Out of Window collision timer begins counting its 512 bit slot time. A 0 causes
the timer to start after the SFD is received. A 1 causes the timer to start after the first bit of the preamble
is received. R/W
Excessive Deferral Timer disable
Setting this bit to 1 will inhibit transmit errors due to excessive deferral. This will inhibit the setting of the
ED status, and the logging of the TxExcessiveDeferral MIB counter. R/W
3
PESEL
Parity Error Detection Action
This bit controls the assertion of SERR when a data parity error is detected while the DP83815 is acting
as the bus master. When set, parity errors will not result in the assertion of SERR. When reset, parity
errors will result in the assertion of SERR, indicating a system error. This bit should be set to a one by
software if the driver can handle recovery from and reporting of data parity errors. R/W
BROM_DIS
Disable Boot ROM interface
bs
2
When set to 1, this bit inhibits the operation of the Boot ROM interface logic. R/W
1
Reserved
(reads return 0)
0
BEM
Big Endian Mode
O
When set, DP83815 will perform bus-mastered data transfers in “big endian” mode. Note that access to
register space is unaffected by the setting of this bit. R/W
43
www.national.com
4.2.3 EEPROM Access Register
The EEPROM Access Register provides an interface for software access to the NMC9306 style EEPROM The default
values given assume that the EEDO line has a pullup resistor to VDD.
Tag: MEAR
Size: 32 bits
Offset: 0008h
Bit
6
Access: Read Write
Bit Name
31-7
Hard Reset: 00000002h
Soft Reset: 00000002h
Description
unused
MDC
MII Management Clock
Controls the value of the MDC pin. When set, the MDC pin is 1; when clear the MDC pin is 0. R/W
5
MDDIR
MII Management Direction
4
MDIO
3
EESEL
2
EECLK
1
EEDO
MII Management Data
te
Controls the direction of the MDIO pin. When set, DP83815 drives the MDIO pin. When clear MDIO bit
reflects the current state of the MDIO pin. R/W
Software access to the MDIO pin (see MDDIR above). R/W
EEPROM Chip Select
Controls the value of the EESEL pin. When set, the EESEL pin is 1; when clear the EESEL pin is 0. R/W
ol
e
EEPROM Serial Clock
Controls the value of the EECLK pin. When set, the EECLK pin is 1; when clear the EECLK pin is 0. R/W
EEPROM Data Out
Returns the current state of the EEDO pin. When set, the EEDO pin is 1; when clear the EEDO pin is 0.
RO
0
EEDI
EEPROM Data In
bs
Controls the value of the EEDI pin. R/W
4.2.4 EEPROM Map
EEPROM
Address
Configuration/Operation Register Bits
Default Value
(16 bits)
CFGSID[0:15]
0001h
CFGSID[16:31]
0400h
0002h
CFGINT[24:31],CFGINT[16:23]
2CD0h
0003h
CFGCS[20],PMCAP[31],PMCAP[21],PMCSR[8],
CFG[13:16],CFG[18:23],CR[2], SOPAS[0]
CF82h
0004h
SOPAS[1:16]
0000h
0005h
SOPAS[17:32]
0000h
0006h
SOPAS[33:47],PMATCH[0]
000Nh
0007h
PMATCH[1:16]
NNNNh
0008h
PMATCH[17:32]
NNNNh
0009h
PMATCH[33:47],WCSR[0]
NNNNh
000Ah
WCSR[1:4],WCSR[9:10],RFCR[20],RFCR[22],
RFCR[27:31],000b (3 bits)
A098h
000Bh
checksum value
XX55
O
0000h
D008h
In the above table:
N denotes the value is dependent on the ethernet MAC ID Number.
X denotes the value is dependent on the checksum value.
44
www.national.com
DP83815
4.0 Register Set (Continued)
PMATCH[47:0] can be accessed via the combination of the RFCR (offset 0048h) and RFDR (offset 004Ch) registers.
PMATCH holds the Ethernet address info. See Section 3.3.3.
The lower 8 bits of the checksum value should be 55h. For the upper 8 bits, add the top 8 data bits to the lower 8 data bits
for each address. Sum the resultant 8 bit values for all addresses and then add 55h. Take the 2’s complement of the final
sum. This 2’s complement number should be the upper 8 bits of the checksum value in the last address.
As an example, consider an EEPROM with two addresses. EEPROM address 0000h contains the data 1234h. EEPROM
address 0001h contains the data 5678h.
12h + 34h = 46h
56h + 78h = CEh
46h + CEh + 55h = 69h
4.2.5 PCI Test Control Register
Tag: PTSCR
Offset: 000Ch
Bit Name
Size: 32 bits
Hard Reset: 00000000h
Access: Read Write
Soft Reset: 00000000h
Description
ol
e
Bit
31-13
te
The 2’s complement of 69h is 97h so the checksum value entered into EEPROM address 0002h would be 9755h.
unused
12
Reserved
Must be written as a 0.
11
10
Reserved
RBIST_RST
SRAM BIST Reset
Setting this bit to 1 allows the SRAM BIST engine to be reset. R/W
9-8
Reserved
bs
Must be written as 0.
7
RBIST_EN
SRAM BIST Enable
Setting this bit to 1 starts the SRAM BIST engine. R/W
6
RBIST_DONE
SRAM BIST Done
This bit is set to one when the BIST has completed its current test. It is cleared when either the BIST
is active or disabled. RO
RBIST_RXFAIL
RX FIFO BIST Fail
O
5
This bit is set to 1 if the SRAM BIST detects a failure in the RX FIFO SRAM. RO
4
RBIST_TXFAIL
TX FIFO Fail
This bit is set to 1 if the SRAM BIST detects a failure in the TX FIFO SRAM. RO
3
RBIST_RXFFAIL
RX Filter RAM BIST Fail
This bit is set to 1 if the SRAM BIST detects a failure in the RX Filter SRAM. RO
2
EELOAD_EN
Enable EEPROM Load
This bit is set to a 1 to manually initiate a load of configuration information from EEPROM. A 1 is
returned while the configuration load from EEPROM is active (approx. 1500 us). R/W
1
EEBIST_EN
Enable EEPROM BIST
This bit is set to a 1 to initiate EEPROM BIST, which verifies the EEPROM data and checksum
without reloading configuration values to the device. A 1 is returned while the EEPROM BIST is
active. R/W
0
EEBIST_FAIL
EE BIST Fail indication
This bit is set to a 1 upon completion of the EEPROM BIST (EEBIST_EN returns 0) if the BIST logic
encountered an invalid checksum. RO
45
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.6 Interrupt Status Register
This register indicates the source of an interrupt when the INTA pin goes active. Enabling the corresponding bits in the
Interrupt Mask Register (IMR) allows bits in this register to produce an interrupt. When an interrupt is active, one or more
bits in this register are set to a “1”. The Interrupt Status Register reflects all current pending interrupts, regardless of the
state of the corresponding mask bit in the IMR. Reading the ISR clears all interrupts. Writing to the ISR has no effect.
Bit
Tag: ISR
Size: 32 bits
Hard Reset: 03008000h
Offset: 0010h
Access: Read Only
Soft Reset: 03008000h
Bit Name
31-26
Description
Reserved
25
TXRCMP
24
RXRCMP
23
DPERR
Transmit Reset Complete
te
Indicates that a requested transmit reset operation is complete.
Receive Reset Complete
Indicates that a requested receive reset operation is complete.
Detected Parity Error
22
SSERR
ol
e
This bit is set whenever CFGCS:DPERR is set, but cleared (like all other ISR bits) when the ISR register
is read.
Signaled System Error
The DP83815 signaled a system error on the PCI bus.
21
RMABT
Received Master Abort
The DP83815 received a master abort generated as a result of target not responding.
20
RTABT
Received Target Abort
The DP83815 received a target abort on the PCI bus.
19-17
16
unused
RXSOVR
Rx Status FIFO Overrun
bs
Set when an overrun condition occurs on the Rx Status FIFO.
15
HIBERR
High Bits Error Set
A logical OR of bits 25-16.
14
PHY
Phy interrupt
Set to 1 when internal phy generates an interrupt.
13
PME
Power Management Event
O
Set when WOL conditioned detected.
12
SWI
11
MIB
Software Interrupt
Set whenever the SWI bit in the CR register is set.
MIB Service
Set when one of the enabled management statistics has reached its interrupt threshold. (See
Section 4.2.23)
10
TXURN
Tx Underrun
Set when a transmit data FIFO underrun condition occurs.
9
TXIDLE
Tx Idle
This event is signaled when the transmit state machine enters the idle state from a non-idle state. This
will happen whenever the state machine encounters an "end-of-list" condition (NULL link field or a
descriptor with OWN clear).
8
TXERR
Tx Packet Error
This event is signaled after the last transmit descriptor in a failed transmission attempt has been updated
with valid status.
46
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
7
TXDESC
Description
Tx Descriptor
This event is signaled after a transmit descriptor when the INTR bit in the CMDSTS field has been
updated.
6
TXOK
Tx Packet OK
This event is signaled after the last transmit descriptor in a successful transmission attempt has been
updated with valid status.
5
RXORN
4
RXIDLE
Rx Overrun
Set when a receive data FIFO overrun condition occurs.
Rx Idle
This event is signaled when the receive state machine enters the idle state from a running state. This will
happen whenever the state machine encounters an "end-of-list" condition (NULL link field or a descriptor
with OWN set).
3
RXEARLY
Rx Early Threshold
2
RXERR
Rx Packet Error
te
Indicates that the initial Rx Drain Threshold has been met by the incoming packet, and the transfer of the
number of bytes specified by the DRTH field in the RXCFG register has been completed by the receive
DMA engine. This interrupt condition will occur only once per packet.
This event is signaled after the last receive descriptor in a failed packet reception has been updated with
valid status.
RXDESC
Rx Descriptor
ol
e
1
This event is signaled after a receive descriptor with the INTR bit set in the CMDSTS field has been
updated.
0
RXOK
Rx OK
Set by the receive state machine following the update of the last receive descriptor in a good packet.
4.2.7 Interrupt Mask Register
bs
This register masks the interrupts that can be generated from the ISR. Writing a “1” to the bit enables the corresponding
interrupt. During a hardware reset, all mask bits are cleared. Setting a mask bit allows the corresponding bit in the ISR to
cause an interrupt. ISR bits are always set to 1, however, if the condition is present, regardless of the state of the
corresponding mask bit.
Tag: IMR
Access: Read Write
O
Offset: 0014h
Size: 32 bits
Bit
Bit Name
31-26
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
unused
25
TXRCMP
24
RXRCMP
23
DPERR
22
SSERR
21
RMABT
Transmit Reset Complete
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Receive Reset Complete
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Detected Parity Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Signaled System Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Received Master Abort
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
47
www.national.com
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
20
RTABT
Description
Received Target Abort
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
19-17
16
unused
RXSOVR
Rx Status FIFO Overrun
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
15
HIERR
High Bits Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
14
PHY
Phy interrupt
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
13
PME
Power Management Event
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
12
SWI
Software Interrupt
11
MIB
MIB Service
te
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
10
TXURN
Tx Underrun
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
TXIDLE
Tx Idle
ol
e
9
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
8
TXERR
Tx Packet Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
7
TXDESC
Tx Descriptor
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
6
TXOK
Tx Packet OK
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
RXORN
Rx Overrun
bs
5
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
4
RXIDLE
Rx Idle
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
3
RXEARLY
Rx Early Threshold
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
RXERR
Rx Packet Error
O
2
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
1
RXDESC
Rx Descriptor
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
0
RXOK
Rx OK
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
48
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.8 Interrupt Enable Register
The Interrupt Enable Register controls the hardware INTR signal.
Tag: IER
Offset: 0018h
Bit
Access: Read Write
Bit Name
31-1
0
Size: 32 bits
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
unused
IE
Interrupt Enable
4.2.9 Transmit Descriptor Pointer Register
This register points to the current Transmit Descriptor.
Offset: 0020h
Bit
Bit Name
31-2
TXDP
Size: 32 bits
Hard Reset: 00000000h
ol
e
Tag: TXDP
te
When set to 1, the hardware INTR signal is enabled. When set to 0, the hardware INTR signal will be
masked, and no interrupts will be generated. The setting of this bit has no effect on the ISR or IMR. This
provides the ability to disable the hardware interrupt to the host with a single access (eliminating the
need for a read-modify-write cycle).
Access: Read Write
Soft Reset: 00000000h
Description
Transmit Descriptor Pointer
unused
O
1-0
bs
The current value of the transmit descriptor pointer. When the transmit state machine is idle, software
must set TXDP to the address of a completed transmit descriptor. While the transmit state machine is
active, TXDP will follow the state machine as it advances through a linked list of active descriptors. If the
link field of the current transmit descriptor is NULL (signifying the end of the list), TXDP will not advance,
but will remain on the current descriptor. Any subsequent writes to the TXE bit of the CR register will
cause the transmit state machine to reread the link field of the current descriptor to check for new
descriptors that may have been appended to the end of the list. Transmit descriptors must be aligned on
an even 32-bit boundary in host memory (A1-A0 must be 0).
49
www.national.com
4.2.10 Transmit Configuration Register
This register defines the Transmit Configuration for DP83815. It controls such functions as Loopback, Heartbeat, Auto
Transmit Padding, programmable Interframe Gap, Fill & Drain Thresholds, and maximum DMA burst size.
Tag: TXCFG
Offset: 0024h
Bit
Bit Name
31
CSI
Size: 32 bits
Access: Read Write
Hard Reset: 00000102h
Soft Reset: 00000102h
Description
Carrier Sense Ignore
Setting this bit to 1 causes the transmitter to ignore carrier sense activity, which inhibits reporting of CRS
status to the transmit status register. When this bit is 0 (default), the transmitter will monitor the CRS
signal during transmission and reflect valid status in the transmit status register and MIB counter block.
This bit must be set to enable full-duplex operation.
HBI
HeartBeat Ignore
te
30
Setting this bit to 1 causes the transmitter to ignore the heartbeat (CD) pulse which follows the packet
transmission and inhibits logging of TXSQEErrors in the MIB counter block. When this bit is set to 0
(default), the transmitter will monitor the heartbeat pulse and log TXSQEErrors to the MIB counter block.
This bit must be set to enable full-duplex operation
29
MLB
MAC Loopback
28
ATP
ol
e
Setting this bit to a 1 places the DP83815 MAC into a loopback state which routes all transmit traffic to
the receiver, and disables the transmit and receive interfaces of the MII. A 0 in this bit allows normal MAC
operation. The transmitter and receiver must be disabled before enabling the loopback mode. (Packets
received during MLB mode will reflect loopback status in the receive descriptor’s cmdsts.LBP field.)
Automatic Transmit Padding
Setting this bit to 1 causes the MAC to automatically pad small (runt) transmit packets to the Ethernet
minimum size of 64 bytes. This allows driver software to transfer only actual packet data. Setting this bit
to 0 disables the automatic padding function, forcing software to control runt padding.
27-26
IFG
Interframe Gap Time
bs
This field allows the user to adjust the interframe gap time below the standard 9.6µs @10 Mb/s and
960ns @100 Mb/s. The time can be programmed from 9.6µs to 8.4µs @10 Mb/s and 960ns to 840ns
@100 Mb/s. Note that any value other than zero may violate the IEEE 802.3 standard. The formula for
the interframe gap is:
9.6µs - 0.4(IFG[1:0]) µs @10 Mb/s and
960ns - 40(IFG[1:0])ns @100 Mb/s
25-24
Reserved
writes are ignored, reads return 00.
ECRETRY
Excessive Collision Retry Enable
O
23
This bit enables automatic retries of excessive collisions. If set, the transmitter will retry the packet up to
4 excessive collision counts, for a total of 64 attempts. If the packet still does not complete successfully,
then the transmission will be aborted after the 64th attempt. If this bit is not set, then the transmit will be
aborted after the 16th attempt. Note that setting this bit will change how collisions are reported in the
status field of the transmit descriptor.
50
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
22-20
MXDMA
Description
Max DMA Burst Size per Tx DMA Burst
This field sets the maximum size of transmit DMA data bursts according to the following table:
000 = 128 32-bit words (512 bytes)
001 = 1 32-bit word (4 bytes)
010 = 2 32-bit words (8 bytes)
011 = 4 32-bit words (16 bytes)
100 = 8 32-bit words (32 bytes)
101 = 16 32-bit words (64 bytes)
110 = 32 32-bit words (128 bytes)
111 = 64 32-bit words (256 bytes)
NOTE: The MXDMA setting value MUST not be greater than the TXCFG:FLTH (Tx Fill Threshold) value.
19-14
unused
FLTH
Tx Fill Threshold
te
13-8
Specifies the fill threshold in units of 32 bytes. When the number of available bytes in the transmit FIFO
reaches this level, the transmit bus master state machine will be allowed to request the PCI bus for
transmit packet fragment reads. A value of 0 in this field will produce unexpected results and must not be
used.
ol
e
Note: The FLTH value should be greater than the TXCFG:MXDMA value, but less than (txFIFOsize TXCFG:DRTH). In order to prevent FIFO pointer overlap internal to the device, the sum of the FLTH and
TXCFG:DRTH values should not exceed 2016 Bytes.
7-6
5-0
unused
DRTH
Tx Drain Threshold
Specifies the drain threshold in units of 32 bytes. When the number of bytes in the FIFO reaches this
level (or the FIFO contains at least one complete packet) the MAC transmit state machine will begin the
transmission of a packet.
bs
NOTE: In order to prevent a deadlock condition from occurring, the DRTH value should always be less
than (txFIFOsize - TXCFG:FLTH). A value of 0 in this field will produce unexpected results and must not
be used. Also, in order to prevent FIFO pointer overlap internal to the device, the sum of the DRTH and
TXCFG:FLTH values should not exceed 2016 Bytes.
4.2.11 Receive Descriptor Pointer Register
This register points to the current Receive Descriptor.
Tag: RXDP
O
Offset: 0030h
Bit
Bit Name
31-2
RXDP
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
Receive Descriptor Pointer
The current value of the receive descriptor pointer. When the receive state machine is idle, software must
set RXDP to the address of an available receive descriptor. While the receive state machine is active,
RXDP will follow the state machine as it advances through a linked list of available descriptors. If the link
field of the current receive descriptor is NULL (signifying the end of the list), RXDP will not advance, but
will remain on the current descriptor. Any subsequent writes to the RXE bit of the CR register will cause
the receive state machine to reread the link field of the current descriptor to check for new descriptors
that may have been appended to the end of the list. Software should not write to this register unless the
receive state machine is idle. Receive descriptors must be aligned on 32-bit boundaries (A1-A0 must be
zero). A 0 written to RXDP followed by a subsequent write to RXE will cause the receiver to enter silent
RX mode, for use during WOL. In this mode packets will be received and buffered in FIFO, but no DMA
to system memory will occur. The packet data may be recovered from the FIFO by writing a valid
descriptor address to RXDP and then strobing RXE.
1-0
unused
51
www.national.com
4.2.12 Receive Configuration Register
This register is used to set the receive configuration for DP83815. Receive properties such as accepting error packets,
runt packets, setting the receive drain threshold etc. are controlled here.
Tag: RXCFG
Offset: 0034h
Bit
Bit Name
31
AEP
Size: 32 bits
Access: Read Write
Hard Reset: 00000002h
Soft Reset: 00000002h
Description
Accept Errored Packets
When set to 1, all packets with CRC, alignment, and/or collision errors will be accepted. When set to 0,
all packets with CRC, alignment, and/or collision errors will be rejected if possible. Note that depending
on the type of error, some packets may be received with errors, regardless of the setting of AEP. These
errors will be indicated in the CMDSTS field of the last descriptor in the packet.
ARP
Accept Runt Packets
te
30
When set to 1, all packets under 64 bytes in length without errors are accepted. When this bit is 0, all
packets less than 64 bytes in length will be rejected if possible.
29
unused
28
ATX
Accept Transmit Packets
27
ALP
ol
e
When set to 1, data received simultaneously to a local transmission (such as during a PMD loopback or
full duplex operation) will be accepted as valid received data. Additionally, when set to 1, the receiver will
ignore collision activity. When set to 0 (default), all data receive simultaneous to a local transmit will be
rejected. This bit must be set to 1 for PMD loopback and full duplex operation.
Accept Long Packets
When set to 1, all packets > 1518 bytes in length and <= 2046 bytes will be treated as normal receive
packets, and will not be tagged as long or error packets. All packets > 2046 bytes in length will be
truncated at 2046 bytes and either rejected from the FIFO, or tagged as long packets. Care must be
taken when accepting long packets to ensure that buffers provided are of adequate length. When ALP is
set to 0, packets larger than 1518 bytes (CRC inclusive) will be truncated at 1514 bytes, and rejected if
possible.
unused
bs
26
25-23
unused
Writes are ignored, reads return 000b.
22-20
MXDMA
Max DMA Burst Size per Rx DMA Burst
This field sets the maximum size of receive DMA data bursts according to the following table:
000 = 128 32-bit words (512 bytes)
O
001 = 1 32-bit word (4 bytes)
010 = 2 32-bit words (8 bytes)
011 = 4 32-bit words (16 bytes)
100 = 8 32-bit words (32 bytes)
101 = 16 32-bit words (64 bytes)
110 = 32 32-bit words (128 bytes)
111 = 64 32-bit words (256 bytes)
19-6
unused
52
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
5-1
DRTH
Description
Rx Drain Threshold
Specifies the drain threshold in units of 8 bytes. When the number of bytes in the receive FIFO reaches
this value (times 8), or the FIFO contains a complete packet, the receive bus master state machine will
begin the transfer of data from the FIFO to host memory. Care must be taken when setting DRTH to a
value lower than the number of bytes needed to determine if packet should be accepted or rejected. In
this case, the packet might be rejected after the bus master operation to begin transferring the packet
into memory has begun. When this occurs, neither the OK bit or any error status bit in the descriptor’s
cmdsts will be set. A value of 0 is illegal, and the results are undefined.
This value is also used to compare with the accumulated packet length for early receive indication. When
the accumulated packet length meets or exceeds the DRTH value, the RXEARLY interrupt condition is
generated.
Reserved
4.2.13 CLKRUN Control/Status Register
te
0
This register mirrors the read/write control of the PMESTS and PMEEN from the PCI Configuration register PMCSR and
controls whether the chip is in the CLKRUNN or PMEN mode.
Tag: CCSR
Bit
Bit Name
31-16
Access: Read Write
Hard Reset: 00000000h
Soft Reset: unchanged
ol
e
Offset: 003Ch
Size: 32 bits
Description
reserved
(reads return 0)
15
PMESTS
PME Status
Sticky bit which represents the state of the PME/CLKRUN logic, regardless of the state of the PMEEN bit.
Mirrored from PCI configuration register PMCSR. Writing a 1 to this bit clears it.
reserved
bs
14-9
(reads return 0)
8
PMEEN
PME Enable
When set to 1, this bit enables the assertion of the PMEN/CLKRUNN pin. When 0, the PMEN/CLKRUNN
pin is forced to be inactive. This value can be loaded from the EEPROM. Mirrored from PCI configuration
register PMCSR.
7-1
unused
O
(reads return 0)
0
CLKRUN_EN Clkrun Enable
When set to 1, this bit enables the CLKRUNN functionality of the PMEN/CLKRUNN pin. When 0, normal
PMEN functionality is active.
53
www.national.com
Situation 1 is a “clock continue” event and can occur if the
DP83815 has not completed a pending packet transmit or
receive. Situation 2 is a “clock start” event and can occur if
the DP83815 has been programmed to a WOL state and it
receives a wake packet, or the PCI clock has simply been
stopped and the receiver has data ready to DMA. In either
of these situations, the DP83815 asserts CLKRUNN until it
detects two rising edges of the PCI clock; it then releases
In the DP83815, CLKRUNN shares a pin with PMEN (pin assertion of CLKRUNN. At this point, the central resource
59). This means the chip cannot be simultaneously PCI is driving CLKRUNN low, and cannot drive it high again
Power Management and PCI Mobile Design Guide- until at least four rising edges of the PCI clock have
compliant; however, it is unlikely that a system would use occurred since the initial CLKRUNN assertion by the
both of these functions simultaneously. The function of the DP83815. Also in either situation, the DP83815 must have
PMEN/CLKRUNN pin is selected with the CLKRUN_EN bit detected CLKRUNN de-asserted for two consecutive rising
edges of the PCI clock before it is allowed to assert
of CCSR.
CLKRUNN.
4.2.13.1 CLKRUNN Function
CLKRUNN is a dual-function optional signal. It is used by
the central PCI clock resource to indicate clock status (i.e.
PCI clock running normally or slowed/stopped), and it is
used by PCI devices to request that the central resource
restart the PCI clock or keep it running normally.
te
CCSR bits 15 and 8 (PMESTS and PMEEN) are mirrored
from PCI configuration space to allow them to be accessed NOTES:
by software. The functionality of these bits is the same as * If a clock start or continue event has completed but a PCI
in the PCI configuration register PMCSR.
interrupt has not been serviced yet, the CLKRUN logic will
not prevent the system from stopping the PCI clock.
ol
e
As an output, CLKRUNN is open-drain like PMEN, i.e. it * If PMEEN is not set, the DP83815 cannot assert
can only drive low. CLKRUNN is an input unless one of the CLKRUNN to request a clock start or continue. In this case,
if the system is going to stop the PCI clock, software must
following two conditions occurs:
shut down the internal PHY to prevent receive errors.
1. the system drives CLKRUNN high but the DP83815 is
not ready for the PCI clock to be stopped or
O
bs
2. the PCI clock is stopped or slowed (CLKRUNN is pulled
high by the system) and the DP83815 requires the use of
the PCI bus.
* If another CLKRUN-enabled device in the system
encounters a clock start or continue event, the cycle of
assertions and de-assertions of CLKRUNN will cause the
DP83815 clock mux to switch the clock to the RX block
back and forth between the PCI clock and the X1 clock
until the event completes.
Subject to change without notice.
54
Rev O
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.14 Wake Command/Status Register
The WCSR register is used to configure/control and monitor the DP83815 Wake On LAN logic. The Wake On LAN logic
is used to monitor the incoming packet stream while in a low-power state, and provide a wake event to the system if the
desired packet type, contents, or Link change are detected.
Tag: WCSR
Offset: 0040h
Bit
Bit Name
31
MPR
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
Magic Packet Received
Set to 1 if a Magic Packet has been detected and the WKMAG bit is set. RO, cleared on read.
30
PATM3
Pattern 3 match
29
PATM2
Pattern 2 match
te
Associated bit set to 1 if a pattern 3 match is detected and the WKPAT3 bit is set. RO, cleared on read.
Associated bit set to 1 if a pattern 2 match is detected and the WKPAT2 bit is set. RO, cleared on read.
28
PATM1
Pattern 1 match
Associated bit set to 1 if a pattern 1 match is detected and the WKPAT1 bit is set. RO, cleared on read.
27
PATM0
Pattern 0 match
26
ARPR
ol
e
Associated bit set to 1 if a pattern 0 match is detected and the WKPAT0 bit is set. RO, cleared on read.
ARP Received
Set to 1 if an ARP packet has been detected and the WKARP bit is set. RO, cleared on read.
25
BCASTR
Broadcast Received
Set to 1 if a broadcast packet has been detected and the WKBCP bit is set. RO, cleared on read.
24
MCASTR
Multicast Received
Set to 1 if a multicast packet has been detected and the WKMCP bit is set. RO, cleared on read.
23
UCASTR
Unicast Received
22
bs
Set to 1 if a unicast packet has been detected the WKUCP bit is set. RO, cleared on read.
PHYINT
Phy Interrupt
Set to 1 if a Phy interrupt was detected and the WKPHY bit is set. RO, cleared on read.
21
Reserved
Reserved
RO, cleared on read.
20
SOHACK
SecureOn Hack Attempt
O
Set to 1 if the MPSOE and WKMAG bits are set, and a Magic Packet is receive with an invalid
SecureOn password value. RO, Cleared on read.
19-11
unused
returns 0
10
MPSOE
9
WKMAG
8
WKPAT3
7
WKPAT2
6
WKPAT1
Magic Packet SecureOn Enable
Enable Magic Packet SecureOn feature. Only applicable when bit 9 is set. R/W
Wake on Magic Packet
Enable wake on Magic Packet detection. R/W
Wake on Pattern 3 match
Enable wake on match of pattern 3. R/W
Wake on Pattern 2 match
Enable wake on match of pattern 2. R/W
Wake on Pattern 1 match
Enable wake on match of pattern 1. R/W
55
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
5
WKPAT0
4
WKARP
3
WKBCP
2
WKMCP
1
WKUCP
0
WKPHY
Description
Wake on Pattern 0 match
Enable wake on match of pattern 0. R/W
Wake on ARP
Enable wake on ARP packet detection. R/W
Wake on Broadcast
Enable wake on broadcast packet detection. R/W
Wake on Multicast
Enable wake on multicast packet detection. R/W
Wake on Unicast
Enable wake on unicast packet detection. R/W
Wake on Phy Interrupt
4.2.14.1 Wake on LAN
host memory for processing. Note that the wake packet is
retained for processing - this is a feature of the DP83815.
In addition to the above Wake on LAN features, DP83815
also provides Wake on Pattern Matching, Wake on DA
match and Wake on Magic Packet.
ol
e
The Wake on LAN logic provides several mechanisms for
bringing the DP83815 out of a low-power state. Wake on
ARP, Wake on Broadcast, Wake on Multicast Hash and
Wake on Phy Interrupt are enabled by setting the
corresponding bit in the Wake Command/Status Register,
WCSR. Before the hardware is programmed to a low
power state, the software must write a null receive
descriptor pointer to the Receive Descriptor Pointer
Register (RXDP) to ensure wake packets will be buffered in
the RX fifo. Please refer to the description of the RXDP
register for this procedure.
te
Enable wake on Phy Interrupt. The Phy interrupt can be programmed for Link Change and a variety of
other Physical Layer events. R/W
Wake on Pattern Matching
O
bs
Wake on Pattern Matching is an extension of the Pattern
Matching feature provided by the Receive Filter Logic.
When one or more of the Wake on Pattern Match bits are
set in the WCSR, a packet will generate a wake event if it
matches the associated pattern buffer. The pattern count
When a qualifying packet is received, the Wake on LAN and the pattern buffer memory are accessed in the same
logic generates a Wake event and pulses the PMEN PCI way as in Pattern Matching for packet acceptance. The
signal to request a Power Management state change. The minimum pattern count is 2 bytes and the maximum pattern
software must then bring the hardware out of low power count is 64 bytes for patterns 0 and 1, and 128 bytes for
mode and, if the Power Management state was D3hot, patterns 2 and 3. Packets are compared on a byte by byte
reinitialize Configuration Register space. A Wake interrupt basis and bytes may be masked in pattern memory, thus
can also be generated which alerts the software that a allowing for don’t cares. Refer to Section 4.2.18 Receive
Wake event has occurred and a packet was received. The Filter Logic for programming examples.
software must then write a valid receive descriptor pointer
to RXDP. The incoming packet can then be transferred into
Subject to change without notice.
56
Rev O
www.national.com
4.2.15 Pause Control/Status Register
The PCR register is used to control and monitor the DP83815 Pause Frame reception logic. The Pause Frame reception
Logic is used to accept 802.3x Pause Frames, extract the pause length value, and initiate a TX MAC pause interval of
the specified number of slot times.
Tag: PCR
Offset: 0044h
Bit
Bit Name
31
PSEN
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
Pause Enable
Manually enables reception of 802.3x pause frames This bit is ORed with the PSNEG bit to enable pause
reception. If pause reception has been enabled via PSEN bit (PSEN=1), setting this bit to 0 will cause
any active pause interval to be terminated. R/W
PS_MCAST
Pause on Multicast
te
30
When set to 1, this bit enables reception of 802.3x pause frames which use the 802.3x designated
multicast address in the DA (01-80-C2-00-00-01). When this mode is enabled, the RX filter logic
performs a perfect match on the above multicast address. No other address filtration modes (including
multicast hash) are required for pause frame reception. R/W
29
PS_DA
Pause on DA
28-24
ol
e
When set to 1, this bit enables reception of a pause frame based on a DA match with either the perfect
match register, or one of the pattern match buffers. R/W
unused
returns 0
23
PS_ACT
Pause Active
This bit is set to a 1 when the TX MAC logic is actively timing a pause interval. RO
22
PS_RCVD
Pause Frame Received
This bit is set to a 1 when a pause frame has been received. This bit will remain set until the TX MAC has
completed the pause interval. RO
PSNEG
Pause Negotiated
bs
21
Status bit indicating that the 802.3x pause function has been enabled via auto-negotiation. This bit will
only be set if DP83815 advertises pause capable by setting bit 16 in the CFG register. RO
20-17
unused
returns 0
16
MLD_EN
Manual Load Enable
O
Setting this bit to a 1 will cause the value of bits 15-0 to be written to the pause count register. This write
operation causes pause count interval will be manually initiated. This bit is not sticky, and reads will
always return 0. WO
15-0
PAUSE_CNT Pause Counter Value
READ: These bits represent the current real-time value of the TX MAC pause counter register.
WRITE: If no pause count interval is in progress (PS_RCVD=0, PS_ACT=0), and MLD_EN=1 this value
is written to the pause count register, and causes pause count interval will be manually initiated.
57
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.16 Receive Filter/Match Control Register
The RFCR register is used to control and configure the DP83815 Receive Filter Control logic. The Receive Filter Control
Logic is used to configure destination address filtering of incoming packets.
Tag: RFCR
Offset: 0048h
Bit
Bit Name
31
RFEN
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
Rx Filter Enable
When this bit is set to 1, the Rx Filter is enabled to qualify incoming packets. When set to a 0, receive
packet filtering is disabled (i.e. all receive packets are rejected). This bit must be 0 for the other bits in this
register to be configured.
30
AAB
Accept All Broadcast
29
AAM
Accept All Multicast
te
When set to a 1, this bit causes all broadcast address packets to be accepted. When set to 0, no
broadcast address packets will be accepted.
When set to a 1, this bit causes all multicast address packets to be accepted. When set to 0, multicast
destination addresses must have the appropriate bit set in the multicast hash table mask in order for the
packet to be accepted.
AAU
Accept All Unicast
ol
e
28
When set to a 1, this bit causes all unicast address packets to be accepted. When set to 0, the
destination address must match the node address value specified through some other means in order for
the packet to be accepted.
27
APM
Accept on Perfect Match
When set to 1, this bit allows the perfect match register to be used to compare against the DA for packet
acceptance. When this bit is 0, the perfect match register contents will not be used for DA comparison.
26-23
APAT
Accept on Pattern Match
22
bs
When one or more of these bits is set to 1, a packet will be accepted if the first n bytes (n is the value
defined in the associated pattern count register) match the associated pattern buffer memory contents.
When a bit is set to 0, the associated pattern buffer will not be used for packet acceptance.
AARP
Accept ARP Packets
When set to 1, this bit allows all ARP packets (packets with a TYPE/LEN field set to 806h) to be
accepted, regardless of the DA value. When set to 0, ARP packets are treated as normal packets and
must meet other DA match criteria for acceptance.
21
MHEN
Multicast Hash Enable
O
When set to 1, this bit allows hash table comparison for multicast addresses, i.e. a hash table hit for a
multicast addressed packet will be accepted. When set to 0, multicast hash hits will not be used for
packet acceptance.
20
UHEN
Unicast Hash Enable
When set to 1, this bit allows hash table comparison for unicast addresses, i.e. a hash table hit for a
unicast addressed packet will be accepted. When set to 0, unicast hash hits will not be used for packet
acceptance.
19
ULM
U/L bit Mask
When set to 1, this bit will cause the U/L bit (2nd MSb) of the DA to be ignored during comparison with
the perfect match register.
18-10
Unused
returns 0
58
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
9-0
RFADDR
Description
Receive Filter Extended Register Address
Selects which internal receive filter register is accessible via RFDR:
Perfect Match Register (PMATCH)
000h - PMATCH octets 1-0
002h - PMATCH octets 3-2
004h - PMATCH octets 5-4
Pattern Count Registers (PCOUNT)
006h - PCOUNT1, PCOUNT0
008h - PCOUNT3, PCOUNT2
SecureOn Password Register (SOPAS)
Filter Memory
te
00Ah - SOPAS octets 1-0
00Ch - SOPAS octets 3-2
00Eh - SOPAS octets 5-4
200h-3FE - Rx filter memory (Hash table/pattern buffers)
4.2.17 Receive Filter/Match Data Register
.
ol
e
The RFDR register is used for reading from and writing to the internal receive filter registers, the pattern buffer memory,
and the hash table memory.
Tag: RFDR
Offset: 004Ch
Bit
Bit Name
31-18
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: 00000000h
Description
unused
BMASK
15-0
RFDATA
Byte mask
bs
17-16
Used as byte mask values for pattern match template data.
O
Receive Filter Data
59
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.18 Receive Filter Logic
Accept on Pattern Match
The Receive Filter Logic supports a variety of techniques
for qualifying incoming packets. The most basic filtering
options include Accept All Broadcast, Accept All Multicast
and Accept All Unicast packets. These options are enabled
by setting the corresponding bit in the Receive Filter
Control Register, RFCR. Accept on Perfect Match, Accept
on Pattern Match, Accept on Multicast Hash and Accept on
Unicast Hash are more robust in their filtering capabilities,
but require additional programming of the Receive Filter
registers and the internal filter RAM.
The Receive Filter Logic provides access to 4 separate
internal RAM-based pattern buffers to be used as
additional perfect match address registers. Pattern buffers
0 and 1 are 64 bytes deep, allowing perfect match on the
first 64 bytes of a packet, and pattern buffers 2 and 3 are
128 bytes deep, allowing perfect match on the first 128
bytes of a packet.
ol
e
te
When one or more of the Pattern Match enable bits are set
in the RFCR, a packet will be accepted if it matches the
Accept on Perfect Match
associated pattern buffer. As indicated above, the pattern
When enabled, the Perfect Match Register is used to buffers are 64 and 128 bytes deep organized as 32 or 64
compare against the DA for packet acceptance. The words, where a word is 18 bits. Bits 17 and 18 of a
Perfect Match Register is a 6-byte register accessed respective word are mask bits for byte 0 and byte 1 of the
indirectly through the RFCR. The address of the internal 16-bit data word (bits 15:0). An incoming packet is
receive filter register to be accessed is programmed compared to each enabled pattern buffer on a byte by byte
through bits 8:0 of the RFCR. The Receive Filter Data basis for a specified count. Masking a pattern byte results
Register, RFDR, is used for reading/writing the actual data. in a byte match regardless of its value (a don’t care). A
count value must be programmed for each pattern buffer to
RX Filter Address: 000h - Perfect Match octets 1-0
be used for comparison. The minimum valid count is 2 (2
002h - Perfect Match octets 3-2
bytes) and the maximum valid count is 32 for pattern
004h - Perfect Match octets 5-4
buffers 0 and 1, and 64 for pattern buffers 2 and 3. The
Octet 0 of the Perfect Match Register corresponds to the pattern count registers are internal receive filter registers
first octet of the packet as it appears on the wire. Octet 5 accessed through the RFCR and the RFDR The Receive
corresponds to the last octet of the DA as it appears on the Filter memory is also accessed through the RFCR and the
wire.
RFDR. A memory map of the internal pattern RAM is
The following steps are required to program the RFCR to shown in Figure 4-1.
accept packets on a perfect match of the DA.
Example: Destination Address of 08-00-17-07-28-55
perfect match register, octets 1-0
write address, octets 1-0
perfect match register, octets 3-2
write address, octets 3-2
perfect match register, octets 5-4
write address, octets 5-4
($RFEN|$APM)
enable filtering, perfect match
O
bs
iow l $RFCR (0000)
iow l $RFDR (0008)
iow l $RFCR (0002)
iow l $RFDR (0717)
iow l $RFCR (0004)
iow l $RFDR (5528)
iow l $RFDR
Subject to change without notice.
60
Rev O
www.national.com
DP83815
Mask Bit
Byte0
Mask Bit
Byte1
4.0 Register Set (Continued)
3FE
Pattern2Word7F
byte1
byte0
3FC
Pattern3Word7E
byte1
byte0
3FA
Pattern2Word7E
byte1
byte0
3F8
....................
byte1
byte0
306
te
Pattern3Word1
....................
byte0
....................
byte1
....................
Pattern3Word7F
Pattern2Word1
Pattern3Word0
Pattern2Word0
byte0
304
byte1
byte0
302
byte1
byte0
300
byte1
byte0
2FE
ol
e
Pattern1Word3F
byte1
Pattern1Word3E
byte1
byte0
2FA
Pattern0Word3E
byte1
byte0
2F8
....................
2FC
....................
byte0
....................
byte1
....................
Pattern0Word3F
byte1
byte0
286
Pattern0Word1
byte1
byte0
284
Pattern1Word0
byte1
byte0
282
Pattern0Word0
byte1
byte0
280
bs
Pattern1Word1
17
16
15
8 7
0
O
Bit#
Figure 4-1 Pattern Buffer Memory - 180h words (word = 18bits)
61
www.national.com
DP83815
4.0 Register Set (Continued)
Example: Pattern match on the following destination addresses:
02-00-03-01-04-02
12-10-13-11-14-12
22-20-23-21-24-22
32-30-33-31-34-32
set $PATBUF01 = 280
set $PATBUF23 = 300
# write counts
iow l $RFCR (0006)
iow l $RFDR (0406)
iow l $RFCR (0008)
iow l $RFDR (0406)
# pattern count registers 1, 0
# count 1 = 4, count 0= 6
# pattern count registers 3, 2
# count 3 = 4, count 2 = 6
O
bs
ol
e
te
# write data pattern into buffer 0
iow l $RFCR ($PATBUF01)
iow l $RFDR (0002)
iow l $RFCR ($PATBUF01 + 4)
iow l $RFDR (0103)
iow l $RFCR ($PATBUF01 + 8)
iow l $RFDR (0204)
# write data pattern into buffer 1
iow l $RFCR ($PATBUF01 + 2)
iow l $RFDR (1012)
iow l $RFCR ($PATBUF01 + 6)
iow l $RFDR (1113)
iow l $RFCR ($PATBUF01 + a)
iow l $RFDR (1214)
# write data pattern into buffer 2
iow l $RFCR ($PATBUF23)
iow l $RFDR (2022)
iow l $RFCR ($PATBUF23 + 4)
iow l $RFDR (2123)
iow l $RFCR ($PATBUF23 + 8)
iow l $RFDR (2224)
# write data pattern into buffer 3
iow l $RFCR ($PATBUF23 +2)
iow l $RFDR (3032)
iow l $RFCR ($PATBUF23 + 6)
iow l $RFDR (3133)
iow l $RFCR ($PATBUF23 + a)
iow l $RFDR (3234)
#enable receive filter on all patterns
iow l $RFCR ($RFEN|$APAT0|$APAT1|$APAT2|$APAT3)
Example of how to mask out a byte in a pattern:
# write data pattern into buffer 0
iow l $RFCR ($PATBUF01)
iow l $RFDR (10002)
iow l $RFCR ($PATBUF01 + 4)
iow l $RFDR (20103)
iow l $RFCR ($PATBUF01 + 8)
iow l $RFDR (30204)
#mask byte 0 (value = 02)
#mask byte 1 (value = 01)
#mask byte 0 and 1
62
www.national.com
Accept on Multicast or Unicast Hash
Hash Table memory. The upper 4 bits represent the word
address and the lower 5 bits select the bit within the word.
If the corresponding bit is set, then the packet is accepted,
otherwise the packet is rejected. The hash table memory is
accessed through the RFCR and the RFDR. Refer to
Figure 4-2 for a memory map. Below is example code for
setting/clearing a bit in the hash table.
Unused
Unused
Multicast and Unicast addresses may be further qualified
by use of the receive filter hash functions. An internal 512
bit (64 byte) RAM-based hash table is used to perform
imperfect filtering of multicast or unicast packets. By
enabling either Multicast Hashing or Unicast Hashing in the
RFCR, the receive filter logic will use the 9 least significant
bits of the destination addresses’ CRC as an index into the
X
byte63
byte62
23E
X
X
byte61
byte60
23C
X
X
byte5
byte4
204
X
X
byte3
byte2
202
ol
e
..............
te
X
X
Bit#
X
byte1
byte0
8 7
17 16 15
200
0
Figure 4-2 Hash Table Memory - 40h bytes addressed on word boundaries
set HASH_TABLE = 200
# compute the CRC of the destination address
bs
crc $DA
set index = ($crc >> 3)
set bit = ($crc & 01f)
# lower 5 bits select which bit in 32 bit word
# write word address into RFCR
iow l $RFCR ($HASH_TABLE + $index)
# use 16 bit register interface into 32bit RAM
O
# select bit to set/clear
if ($bit > f) set bit = ($bit - 010h)
set hash_bit = (0001 << $bit)
# read indexed word from table
ior l $RFDR
if ($SetBit) then
set hash_word = ($rc | $hash_bit)
iow l $RFDR ($hash_word)
else
set hash_bit = (~$hash_bit)
set hash_word = ($rc & $hash_bit)
iow l $RFDR ($hash_word)‘
endif
iow l $RFCR ($RFEN|$MHEN|$UHEN)# enable multicast and/or unicast
# address hashing
Subject to change without notice.
63
Rev O
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
4.2.19 Boot ROM Address Register
The BRAR is used to setup the address for an access to an external ROM/FLASH device.
Tag: BRAR
Offset: 0050h
Bit
Bit Name
31
AUTOINC
Size: 32 bits
Access: Read Write
Hard Reset: FFFFFFFFh
Soft Reset: unchanged
Description
Auto-Increment
When set, the contents of ADDR will auto increment with every 32-bit access to the BRDR register.
30-16
15-0
unused
ADDR
Boot ROM Address
te
16-bit address used to access the external Boot ROM.
4.2.20 Boot ROM Data Register
The BRDR is used to read and write ROM/FLASH data from the data from/to an external ROM/FLASH device.
Offset: 0054h
Bit
Bit Name
31-0
DATA
Size: 32 bits
Hard Reset: undefined
ol
e
Tag: BRDR
Access: Read Write
Soft Reset: undefined
Description
Boot ROM Data
bs
Access port to external Boot ROM. Software can use BRAR and BRDR to read (and write if FLASH
memory is used) the external Boot ROM. All accesses must be 32-bits wide and aligned on 32-bit
boundaries.
4.2.21 Silicon Revision Register
Size: 32 bits
Access: Read Only
O
Tag: SRR
Offset: 0058h
Bit
Bit Name
31-16
Hard Reset: as defined
Soft Reset: unchanged
Description
unused
(reads return 0)
15-0
Rev
Revision Level
SRR register value for the DP83815 silicon.
DP83815CVNG
00000302h
DP83815DVNG/UJB 00000403h
64
www.national.com
4.2.22 Management Information Base Control Register
The MIBC register is used to control access to the statistics block and the warning bits and to control the collection of
management information statistics.
Tag: MIBC
Offset: 005ch
Bit
Access: Read Write
Bit Name
31-4
3
Size: 32 bits
Hard Reset: 00000002h
Soft Reset: 00000002h
Description
unused
MIBS
MIB Counter Strobe
Writing a 1 to this bit location causes the counters in all enabled blocks to increment by 1, providing a
single-step test function. The MIBS bit is always read back as 0. This bit is used for test purposes
only and should be set to 0 for normal counter operation.
ACLR
Clear all counters
te
2
When set to a 1, this bit forces all counters to be reset to 0. This bit is always read back as 0.
1
FRZ
Freeze all counters
When set to a 1, this bit forces count values to be frozen such that a read of the statistic block will
represent management statistics at a given instant in time. When set to 0, the counters will increment
normally and may be read individually while counting. While frozen events will not be recorded.
WRN
Warning Test Indicator
ol
e
0
O
bs
This field is read only. This bit is set to 1 when statistic counters have reached their respective overflow
warning condition. WRN will be cleared after one or more of the statistic counters have been cleared.
65
www.national.com
DP83815
4.0 Register Set (Continued)
4.2.23 Management Information Base Registers
"software" counters must be updated. Sizes for specific
hardware statistic counters were chosen such that the
count values will not roll over in less than 15 ms if
incremented at the theoretical maximum rates described in
the above specifications. However, given that the
theoretical maximum counter rates do not represent
realistic network traffic and events, the actual rollover rates
for the hardware counters are more likely to be on the
order of several seconds. The hardware counters are
updated automatically by the MAC on the occurrence of
each event.
The counters provide a set of statistics compliant with the
following management specifications: MIB II, Ether-like
MIB, and IEEE MIB. The values provided are accessed
through the various registers as shown below. All MIB
counters are cleared to 0 when read.
Due to cost and space limitations, the counter bit widths
provided in the DP83815 MIB are less than the bit widths
called for in the above specifications. It is assumed that
management agent software will maintain a set of fully
compliant statistic values ("software" counters), utilizing the
hardware counters to reduce the frequency at which these
Table 4-3 MIB Registers
Offset
Tag
Size
warning
(MS bits)
0060h
RXErroredPkts
16
8
Packets received with errors. This counter is incremented for each
packet received with errors. This count includes packets which are
automatically rejected from the FIFO due to both wire errors and
FIFO overruns.
0064h
RXFCSErrors
8
4
Packets received with frame check sequence errors. This counter is
incremented for each packet received with a Frame Check
Sequence error (bad CRC).
ol
e
te
Description
Note: For the MII interface, an FCS error is defined as a resulting
invalid CRC after CRS goes invalid and an even number of bytes
have been received.
0068h
RXMsdPktErrors
8
4
Packets missed due to FIFO overruns. This counter is incremented
for each receive aborted due to data or status FIFO overruns
(insufficient buffer space).
006Ch
RXFAErrors
8
4
Packets received with frame alignment errors. This counter is
incremented for each packet received with a Frame Check
Sequence error (bad CRC).
RXSymbolErrors
O
0070h
bs
Note: For the MII interface, an FAE error is defined as a resulting
invalid CRC on the last full octet, and an odd number of nibbles have
been received (Dribble nibble condition with a bad CRC).
8
4
Packets received with one or more symbol errors. This counter is
incremented for each packet received with one or more symbol
errors detected.
Note: For the MII interface, a symbol error is indicated by the RXER
signal becoming active for one or more clocks while the RXDV signal
is active (during valid data reception).
0074h
RXFrameTooLong
4
2
Packets received with length greater than 1518 bytes (too long
packets). This counter is incremented for each packet received with
greater than the 802.3 standard maximum length of 1518 bytes.
0078h
TXSQEErrors
4
2
Loss of collision heartbeat during transmission. This counter is
incremented when the collision heartbeat pulse is not detected by
the PMD after a transmission.
Subject to change without notice.
66
Rev O
www.national.com
DP83815
4.0 Register Set (Continued)
4.3 Internal PHY Registers
The Internal Phy Registers are only 16 bits wide. Bits [31:16] are not used. In the following register definitions under the
‘Default’ heading, the following definitions hold true:
—
—
—
—
—
—
—
RW=Read Write access
RO=Read Only access
LL=Latched Low and held until read, based upon the occurrence of the corresponding event
LH=Latched High and held until read, based upon the occurrence of the corresponding event
SC=Register sets on event occurrence and Self-Clears when event ends
P=Register bit is Permanently set to a default value
COR=Clear On Read
4.3.1 Basic Mode Control Register
Offset: 0080h
Size: 16 bits
Hard Reset: XX00h
te
Tag: BMCR
Access: Read Write
Bit
Bit Name
15
Reset
14
Loopback
Loopback: Default: 0
1 = Loopback enabled
0 = Normal operation
The loopback function enables MII transmit data to be routed to the MII receive data path.
Setting this bit may cause the de-scrambler to lose synchronization and produce a 500 µs “dead time”
before any valid data will appear at the MII receive outputs.
13
Speed
Selection
Speed Select: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
When auto-negotiation is disabled writing to this bit allows the port speed to be selected.
1 = 100 Mb/s
0 = 10 Mb/s
AutoNegotiation
Enable
Power Down
ol
e
Auto-Negotiation Enable: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
1 = Auto-Negotiation Enabled - bits 8 and 13 of this register are ignored when this bit is set.
0 = Auto-Negotiation Disabled - bits 8 and 13 determine the port speed and duplex mode.
Power Down: Default: 0
1 = Power down
0 = Normal operation
Setting this bit powers down the port.
O
11
bs
12
Description
Reset: Default: 0, RW/SC
1 = Initiate software Reset / Reset in Process
0 = Normal operation
This bit, which is self-clearing, returns a value of one until the reset process is complete. The configuration
is re-strapped.
10
Isolate
Isolate: Default: 0
1 = Isolates the port from the MII with the exception of the serial management.
0 = Normal operation
9
Restart Auto- Restart Auto-Negotiation: Default: 0, RW/SC
Negotiation 1 = Restart Auto-Negotiation
0 = Normal operation
When this bit is set, it re-initiates the Auto-Negotiation process. If Auto-Negotiation is disabled (bit 12 =
0), this bit is ignored. This bit is self-clearing and will remain a value of 1 until Auto-Negotiation is initiated,
whereupon it will self-clear. Operation of the Auto-Negotiation process is not affected by the management
entity clearing this bit.
8
Duplex Mode Duplex Mode: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
When auto-negotiation is disabled writing to this bit allows the port Duplex capability to be selected.
1 = Full Duplex operation
0 = Half Duplex operation
67
www.national.com
DP83815
4.0 Register Set (Continued)
Bit
7
6:0
Bit Name
Description
Collision Test Collision Test: Default: 0
1 = Collision test enabled
0 = Normal operation
When set, this bit will cause the COL signal to be asserted in response to the assertion of TXEN within
512-bit times. The COL signal will be de-asserted within 4-bit times in response to the de-assertion of
TXEN.
Reserved
Reserved: Default: 0, RO
4.3.2 Basic Mode Status Register
Tag: BMSR
Offset: 0084h
Access: Read Only
Bit Name
Description
100BASE-T4 100BASE-T4 Capable: Default: 0
0 = Device not able to perform 100BASE-T4 mode.
14
100BASE-TX 100BASE-TX Full Duplex Capable: Default: 1
Full Duplex 1 = Device able to perform 100BASE-TX in full duplex mode
13
100BASE-TX 100BASE-TX Half Duplex Capable: Default: 1
Half Duplex 1 = Device able to perform 100BASE-TX in half duplex mode.
ol
e
15
12
10BASE-T
Full Duplex
10BASE-T Full Duplex Capable: Default: 1
1 = Device able to perform 10BASE-T in full duplex mode
11
10BASE-T
Half Duplex
10BASE-T Half Duplex Capable: Default: 1
1 = Device able to perform 10BASE-T in half duplex mode
10:7
Reserved
6
Preamble
Suppression
Preamble suppression Capable: Default: 1
1 = Device able to perform management transaction with preamble suppressed, 32-bits of preamble
needed only once after reset, invalid opcode or invalid turnaround.
0 = Normal management operation
AutoNegotiation
Complete
Auto-Negotiation Complete: Default: 0
1 = Auto-Negotiation process complete
0 = Auto-Negotiation process not complete
Remote Fault Remote Fault: Default: 0/L(H)
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far End Fault Indication
or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected
O
4
Reserved: Write as 0, read as 0
bs
5
Hard Reset: 7849h
te
Bit
Size: 16 bits
3
AutoNegotiation
Ability
Auto Configuration Ability: Default: 1
1 = Device is able to perform Auto-Negotiation
0 = Device is not able to perform Auto-Negotiation
2
Link Status
Link Status: Default: 0/L(L)
1 = Valid link established (for either 10 or 100 Mb/s operation)
0 = Link not established
The criteria for link validity is implementation specific. The occurrence of a link failure condition will cause
the Link Status bit to clear. Once cleared, this bit may only be set by establishing a good link condition
and a read via the management interface.
1
0
Jabber Detect Jabber Detect: Default: 0/LH
1 = Jabber condition detected
0 = No Jabber
This bit is implemented with a latching function, such that the occurrence of a jabber condition causes it
to set until it is cleared by a read to this register by the management interface or by a reset.
This bit only has meaning in 10 Mb/s mode.
Extended
Capability
Extended Capability: Default: 1
1 = Extended register capabilities
0 = Basic register set capabilities only
68
www.national.com
DP83815
4.0 Register Set (Continued)
4.3.3 PHY Identifier Register #1
The PHY Identifier Registers #1 and #2 together form a unique identifier for the PHY section of this device. The Identifier
consists of a concatenation of the Organizationally Unique Identifier (OUI), the vendor's model number and the model
revision number. A PHY may return a value of zero in each of the 32 bits of the PHY Identifier if desired. The PHY
Identifier is intended to support network management. National Semiconductor's IEEE assigned OUI is 080017h.
Tag: PHYIDR1
Offset: 0088h
Size: 16 bits
Hard Reset: 2000h
Access: Read Only
Bit Name
Description
OUI_MSB
OUI Most Significant Bits: Default: <0010 0000 0000 0000>
Bits 3 to 18 of the OUI (080017h) are stored in bits 15 to 0 of this register. The most significant two bits of
the OUI are ignored (the IEEE standard refers to these as bits 1 and 2).
te
Bit
15:0
4.3.4 PHY Identifier Register #2
Tag: PHYIDR2
Size: 16 bits
Hard Reset: 5C21h
Access: Read Only
ol
e
Offset: 008Ch
Bit
Bit Name
15:10
OUI_LSB
OUI Least Significant Bits: Default: <01 0111>
Bits 19 to 24 of the OUI (080017h) are mapped to bits 15 to 10 of this register respectively.
Description
9:4
VNDR_MDL
Vendor Model Number: Default: <00 0010>
The six bits of vendor model number are mapped to bits 9 to 4 (most significant bit to bit 9).
3:0
MDL_REV
bs
Model Revision Number: Default: <0001>
Four bits of the vendor model revision number are mapped to bits 3 to 0 (most significant bit to bit 3). This
field will be incremented for all major device changes.
4.3.5 Auto-Negotiation Advertisement Register
This register contains the advertised abilities of this device as they will be transmitted to its link partner during AutoNegotiation.
O
Tag: ANAR
Offset: 0090h
Bit
Bit Name
15
NP
14
Reserved
13
RF
12:11
Reserved
10
PAUSE
Size: 16 bits
Hard Reset: 05E1h
Access: Read Write
Description
Next Page Indication: Default: 0
0 = Next Page Transfer not desired
1 = Next Page Transfer desired
Reserved by IEEE: Writes ignored, Read as 0
Remote Fault: Default: 0
1 = Advertises that this device has detected a Remote Fault
0 = No Remote Fault detected
Reserved for Future IEEE use: Write as 0, Read as 0
PAUSE: Default: dependent on the setting of the PAUSE_ADV in the CFG register
1 = Advertise that the DTE (MAC) has implemented both the optional MAC control sublayer and the pause
function as specified in clause 31 and annex 31B of 802.3u.
0 = No MAC based full duplex flow control
69
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
9
T4
8
TX_FD
7
TX
6
10_FD
5
10
4:0
Selector
Description
100BASE-T4 Support: Default: 0/ RO
1= 100BASE-T4 is supported by the local device
0 = 100BASE-T4 not supported
100BASE-TX Full Duplex Support: Default: dependent on setting of the ANEG_SEL in the CFG register
1 = 100BASE-TX Full Duplex is supported by the local device
0 = 100BASE-TX Full Duplex not supported
100BASE-TX Support: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
1 = 100BASE-TX is supported by the local device
0 = 100BASE-TX not supported
10BASE-T Full Duplex Support: Default: dependent on setting of the ANEG_SEL in the CFG register
1 = 10BASE-T Full Duplex is supported by the local device
0 = 10BASE-T Full Duplex not supported
te
10BASE-T Support: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
1 = 10BASE-T is supported by the local device
0 = 10BASE-T not supported
Protocol Selection Bits: Default: <00001>
These bits contain the binary encoded protocol selector supported by this port. <00001> indicates that
this device supports IEEE 802.3u.
ol
e
4.3.6 Auto-Negotiation Link Partner Ability Register
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The content
changes after the successful auto-negotiation if Next-pages are supported.
Tag: ANLPAR
Offset: 0094h
15
Access: Read Only
NP
Description
ACK
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer
1 = Link Partner desires Next Page Transfer
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word
0 = Not acknowledged
The Device's Auto-Negotiation state machine will automatically control this bit based on the incoming FLP
bursts.
O
14
Bit Name
Hard Reset: 0000h
bs
Bit
Size: 16 bits
13
RF
12:10
Reserved
9
T4
8
TX_FD
7
TX
6
10_FD
Remote Fault:
1 = Remote Fault indicated by Link Partner
0 = No Remote Fault indicated by Link Partner
Reserved for Future IEEE use: Write as 0, read as 0
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the Link Partner
0 = 100BASE-T4 not supported by the Link Partner
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the Link Partner
0 = 100BASE-TX Full Duplex not supported by the Link Partner
100BASE-TX Support:
1 = 100BASE-TX is supported by the Link Partner
0 = 100BASE-TX not supported by the Link Partner
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the Link Partner
0 = 10BASE-T Full Duplex not supported by the Link Partner
70
www.national.com
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
5
10
10BASE-T Support:
1 = 10BASE-T is supported by the Link Partner
0 = 10BASE-T not supported by the Link Partner
Description
4:0
Selector
Protocol Selection Bits:
Link Partners’s binary encoded protocol selector.
4.3.7 Auto-Negotiate Expansion Register
This register contains additional Local Device and Link Partner status information.
Tag: ANER
Bit
Bit Name
15:5
Reserved
4
PDF
Access: Read Only
Description
Reserved: Writes ignored, Read as 0.
Parallel Detection Fault:
1 = A fault has been detected via the Parallel Detection function
0 = A fault has not been detected
ol
e
3
LP_NP_ABLE Link Partner Next Page Able:
1 = Link Partner does support Next Page
0 = Link Partner does not support Next Page
2
NP_ABLE
Next Page Able:
1 = Indicates local device is able to send additional “Next Pages”
1
PAGE_RX
Link Code Word Page Received: RO/COR
1 =Link Code Word has been received, cleared on a read
0 = Link Code Word has not been received
LP_AN_ABLE Link Partner Auto-Negotiation Able:
1 = Indicates that the Link Partner supports Auto-Negotiation
0 = Indicates that the Link Partner does not support Auto-Negotiation
bs
0
Hard Reset: 0004h
te
Offset: 0098h
Size: 16 bits
4.3.8 Auto-Negotiation Next Page Transmit Register
O
This register contains the next page information sent by this device to its Link Partner during Auto-Negotiation.
Tag: ANNPTR
Offset: 009Ch
Bit
Bit Name
15
NP
14
Reserved
13
MP
Size: 16 bits
Hard Reset: 2001h
Access: Read Write
Description
Next Page Indication: Default: 0
0 = No other Next Page Transfer desired
1 = Another Next Page desired
Reserved: Writes ignored, read as 0
Message Page: Default: 1
1 = Message Page
0 = Un-formatted Page
71
www.national.com
Bit
Bit Name
12
ACK2
Acknowledge2: Default: 0
1 = Will comply with message
0 = Cannot comply with message
Acknowledge2 is used by the next page function to indicate that Local Device has the ability to comply
with the message received.
Description
11
TOG_TX
Toggle: Default: 0, RO
1 = Value of toggle bit in previously transmitted Link Code Word was 0
0 = Value of toggle bit in previously transmitted Link Code Word was 1
Toggle is used by the Arbitration function within Auto-Negotiation to ensure synchronization with the Link
Partner during Next Page exchange. This bit shall always take the opposite value of the Toggle bit in the
previously exchanged Link Code Word.
10:0
CODE
te
Code Field: Default: <000 0000 0001>
This field represents the code field of the next page transmission. If the MP bit is set (bit 13 of this
register), then the code shall be interpreted as a "Message Page”, as defined in annex 28C of IEEE
802.3u. Otherwise, the code shall be interpreted as an "Un-formatted Page”, and the interpretation is
application specific.
The default value of the CODE represents a Null Page as defined in Annex 28C of IEEE 802.3u.
4.3.9 PHY Status Register
ol
e
This register provides a single location within the register set for quick access to commonly accessed information.
Tag: PHYSTS
Offset: 00C0h
Bit
Bit Name
15:14
Reserved
12
Description
Reserved: Write ignored, read as 0.
Receive Error Receive Error Latch:
Latch
This bit will be cleared upon a read of the RECR register.
1 = Receive error event has occurred since last read of RXERCNT (address 0xD4)
0 = No receive error event has occurred
Polarity
Status
False Carrier
Sense Latch
Polarity Status:
This bit is a duplication of bit 4 in the TBTSCR register. This bit will be cleared upon a read of the TBTSCR
register, but not upon a read of the PHYSTS register.
1 = Inverted Polarity detected
0 = Correct Polarity detected
False Carrier Sense Latch: Default: 0, RO/LH
This bit will be cleared upon a read of the FCSR register.
1 = False Carrier event has occurred since last read of FCSCR (address 0xD0)
0 = No False Carrier event has occurred
O
11
Hard Reset: 0000h
bs
13
Size: 16 bits
Access: Read Only
10
Signal Detect Signal Detect: Default: 0, RO/LL
100BASE-TX unconditional Signal Detect from PMD.
9
De-scrambler De-scrambler Lock: Default: 0, RO/LL
Lock
100BASE-TX De-scrambler Lock from PMD.
8
Page
Received
7
MII Interrupt
Link Code Word Page Received:
This is a duplicate of the Page Received bit in the ANER register, but this bit will not be cleared upon a
read of the PHYSTS register.
1 = A new Link Code Word Page has been received. Cleared on read of the ANER (address 0x06, bit 1)
0 = Link Code Word Page has not been received
MII Interrupt Pending: Default: 0, RO/LH
1 = Indicates that an internal interrupt is pending, cleared by the current read
0 = No interrupt pending
72
www.national.com
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
Description
6
Remote Fault Remote Fault:
1 = Remote Fault condition detected (cleared on read of BMSR (address 0x84h) register or by reset).
Fault criteria: notification from Link Partner of Remote Fault via Auto-Negotiation
0 = No remote fault condition detected
5
Jabber Detect Jabber Detect: This bit only has meaning in 10 Mb/s mode
This bit is a duplicate of the Jabber Detect bit in the BMSR register, except that it is not cleared upon a
read of the PHYSTS register.
1 = Jabber condition detected
0 = No Jabber
4
Auto-Neg.
Complete
Auto-Negotiation Complete:
1 = Auto-Negotiation complete
0 = Auto-Negotiation not complete
3
Loopback
Status
Loopback:
1 = Loopback enabled
0 = Normal operation
Duplex Status Duplex:
This bit indicates duplex status and is determined from Auto-Negotiation or Forced Modes.
1 = Full duplex mode
0 = Half duplex mode
Note: This bit is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if AutoNegotiation is disabled and there is a valid link.
1
Speed Status Speed10:
This bit indicates the status of the speed and is determined from Auto-Negotiation or Forced Modes.
1 = 10 Mb/s mode
0 = 100 Mb/s mode
Note: This bit is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if AutoNegotiation is disabled and there is a valid link.
ol
e
Link Status
Link Status:
This bit is a duplicate of the Link Status bit in the BMSR register, except that it will not be cleared upon a
read of the PHYSTS register.
1 = Valid link established (for either 10 or 100 Mb/s operation)
0 = Link not established
O
bs
0
te
2
73
www.national.com
DP83815
4.0 Register Set (Continued)
4.3.10 MII Interrupt Control Register
This register implements the MII Interrupt PHY Specific Control register. Sources for interrupt generation include: Link
State Change, Jabber Event, Remote Fault, Auto-Negotiation Complete or any of the counters becoming half-full. Note
that the TINT bit operates independently of the INTEN bit. In other words, INTEN does not need to be active to generate
the test interrupt.
Tag: MICR
Offset: 00C4h
Bit
Bit Name
15:2
Reserved
1
INTEN
0
TINT
Size: 16 bits
Hard Reset: 0000h
Access: Read Write
Description
Reserved: Writes ignored, Read as 0
Interrupt Enable:
1 = Enable event based interrupts
0 = Disable event based interrupts
ol
e
te
Test Interrupt:
Forces the PHY to generate an interrupt at the end of each management read to facilitate interrupt testing.
1 = Generate an interrupt
0 = Do not generate interrupt
4.3.11 MII Interrupt Status and Misc. Control Register
This register implements the MII Interrupt PHY Control and Status information. These Interrupts are PHY based events.
When any of these events occur and its respective bit is not masked, and MICR:INTEN is enabled, the interrupt will be
signalled in ISR:PHY.
Tag: MISR
Bit
15
14
Bit Name
MINT
Hard Reset: 0000h
Access: Read Write
bs
Offset: 00C8h
Size: 16 bits
Description
MII Interrupt Pending: Default: 0, RO/COR
1 = Indicates that an interrupt is pending and is cleared by the current read.
0 = no interrupt pending
MSK_LINK
Mask Link: When this bit is 0, the change of link status event will cause the interrupt to be seen by the ISR.
MSK_JAB
Mask Jabber: When this bit is 0, the Jabber event will cause the interrupt to be seen by the ISR.
MSK_RF
Mask Remote Fault: When this bit is 0, the Remote Fault event will cause the interrupt to be seen by the
ISR.
11
MSK_ANC
Mask Auto-Neg. Complete: When this bit is 0, the Auto-negotiation complete event will cause the interrupt to be seen by the ISR.
10
MSK_FHF
Mask False Carrier Half Full: When this bit is 0, the False Carrier Counter Register half-full event will
cause the interrupt to be seen by the ISR.
9
MSK_RHF
Mask Rx Error Half Full: When this bit is 0, the Receive Error Counter Register half-full event will cause
the interrupt to be seen by the ISR.
8:0
Reserved
Reserved: Default: 0, RO
13
O
12
74
www.national.com
DP83815
4.0 Register Set (Continued)
4.3.12 False Carrier Sense Counter Register
This counter provides information required to implement the “FalseCarriers” attribute within the MAU managed object
class of Clause 30 of the IEEE 802.3u specification.
Tag: FCSCR
Offset: 00D0h
Bit
Size: 16 bits
Access: Read Write
Bit Name
15:8
Description
Reserved
Reserved: Writes ignored, Read as 0
FCSCNT[7:0] False Carrier Event Counter: Default: 0, RW/COR
This 8-bit counter increments on every false carrier event. This counter sticks when it reaches its max
count (FFh).
te
7:0
Hard Reset: 0000h
4.3.13 Receiver Error Counter Register
This counter provides information required to implement the “SymbolErrorDuringCarrier” attribute within the PHY
managed object class of Clause 30 of the IEEE 802.3u specification.
Offset: 00D4h
Bit
15:8
Reserved
Hard Reset: 0000h
Access: Read Write
Description
Reserved: Writes ignored, Read as 0
RXERCNT[7:0] RXER Counter: Default: 0, RW / COR
This 8-bit counter increments for each receive error detected. when a valid carrier is present and there
is at least one occurrence of an invalid data symbol. This event can increment only once per valid
carrier event. If a collision is present, the attribute will not increment. The counter sticks when it
reaches its max count.
bs
7:0
Bit Name
Size: 16 bits
ol
e
Tag: RECR
4.3.14 100 Mb/s PCS Configuration and Status Register
Tag: PCSR
Bit
Hard Reset: 0100h
Access: Read Write
O
Offset: 00D8h
Size: 16 bits
Bit Name
Description
15:13
Reserved
Reserved: Writes ignored, Read as 0
12
BYP_4B5B
Bypass 4B/5B Encoding:
1 = 4B5B encoder functions bypassed
0 = Normal 4B5B operation
11
FREE_CLK
Receive Clock:
1 = RX_CK is free-running
0 = RX_CK phase adjusted based on alignment
10
TQ_EN
9
SD_FORCE_B
100 Mb/s True Quiet Mode Enable:
1 = Transmit True Quiet Mode
0 = Normal Transmit Mode
Signal Detect Force:
1 = Forces Signal Detection
0 = Normal SD operation
75
www.national.com
DP83815
4.0 Register Set (Continued)
DP83815
4.0 Register Set (Continued)
Bit
Bit Name
8
SD_OPTION
7:6
Reserved
Reserved: Read as 0
FORCE_100_OK Force 100 Mb/s Good Link:
OR’ed with MAC_FORCE_LINK_100 signal.
1 = Forces 100 Mb/s Good Link
0 = Normal 100 Mb/s operation
4:3
Reserved
Reserved: Read as 0
2
NRZI_BYPASS
1:0
Reserved
NRZI Bypass Enable:
1 = NRZI Bypass Enabled
0 = NRZI Bypass Disabled
Reserved: Read as 0
4.3.15 PHY Control Register
Tag: PHYCR
Size: 16 bits
Access: Read Write
Bit
Bit Name
15:12
Reserved
Reserved
11
PSR_15
BIST Sequence select: Selects length of LFSR used in BIST
1 = PSR15 selected
0 = PSR9 selected
10
BIST_STATUS
BIST Test Status: Default: 0, LL/RO
1 = BIST pass
0 = BIST fail. Latched, cleared by write to BIST start bit.
BIST_START
BIST Start: BIST runs continuously until stopped. Minimum time to run should be 1 ms.
1 = BIST start
0 = BIST stop
BP_STRETCH
Bypass LED Stretching:
This will bypass the LED stretching and the LEDs will reflect the internal value.
1 = Bypass LED stretching
0 = Normal operation
O
8
Description
bs
9
Hard Reset: 003Fh
ol
e
Offset: 00E4h
te
5
Description
Signal Detect Option:
1 = Enhanced signal detect algorithm
0 = Reduced signal detect algorithm
7
PAUSE_STS
6:5
Reserved
4:0
PHYADDR[4:0]
Pause Compare Status: Default: 0, RO
0 = Local Device and the Link Partner are not Pause capable
1 = Local Device and the Link Partner are both Pause capable
Reserved
PHY Address: Default: <11111b>, RW
PHY address for the port.
76
www.national.com
DP83815
4.0 Register Set (Continued)
4.3.16 10BASE-T Status/Control Register
Tag: TBTSCR
Offset: 00E8h
Bit
15:9
8
Size: 16 bits
Hard Reset: 0004h
Access: Read Write
Bit Name
Description
Unused
LOOPBACK_10_DIS 10BASE-T Loopback Disable:
This bit is OR’ed with bit 14 (Loopback) in the BMCR.
1 = 10 Mb/s Loopback is enabled
0 = 10 Mb/s Loopback is disabled
LP_DIS
Normal Link Pulse Disable:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
1 = Transmission of NLPs is disabled
0 = Transmission of NLPs is enabled
6
FORCE_LINK_10
Force 10 Mb/s Good Link:
This bit is OR’ed with the MAC_FORCE_LINK_10 signal.
1 = Forced Good 10 Mb/s Link
0 = Normal Link Status
5
FORCE_POL_COR
4
POLARITY
3
AUTOPOL_DIS
1
ol
e
Reserved
HEARTBEAT_DIS
JABBER_DIS
O
0
Force 10 Mb/s Polarity Correction:
1 = Force inverted polarity
0 = Normal polarity
10 Mb/s Polarity Status: RO/LH
This bit is a duplication of bit 12 in the PHYSTS register. Both bits will be cleared upon a read of
either register.
1 = Inverted Polarity detected
0 = Correct Polarity detected
Auto Polarity Detection & Correction Disable:
1 = Polarity Sense & Correction disabled
0 = Polarity Sense & Correction enabled
bs
2
te
7
Reserved
This bit must be written as a one.
Heartbeat Disable: This bit only has influence in half-duplex 10 Mb/s mode.
1 = Heartbeat function disabled
0 = Heartbeat function enabled
When the device is operating at 100 Mb/s or configured for full duplex, this bit will be ignored - the
heartbeat function is disabled.
Jabber Disable:
Applicable only in 10BASE-T Full Duplex.
1 = Jabber function disabled
0 = Jabber function enabled
77
www.national.com
DP83815
4.0 Register Set (Continued)
4.4 Recommended Registers Configuration
For optimum performance of the DP83815, version noted
as DP83815CVNG (SRR = 302h), the listed register
modifications must be followed in sequence. The table
below contains the register’s offset address value. The
register address consists of: I/O Base Address + Offset
Address. All values are given in hex.
Register Tag
Offset Address
Register
Value
1.
00CCh
PGSEL
0001h
2.
00E4h
PMDCSR
189Ch
3.
00FCh
TSTDAT
0000h
4.
00F4h
DSPCFG
5040h
5.
00F8h
SDCFG
008Ch
O
bs
ol
e
All other registers can remain at their default values, or
desired configuration settings.
te
Register
Subject to change without notice.
78
Rev O
www.national.com
5.1 Overview
The buffer management scheme used on the DP83815
allows quick, simple and efficient use of the frame buffer
memory. Frames are saved in similar formats for both
transmit and receive. The buffer management scheme also
uses separate buffers and descriptors for packet
information. This allows effective transfers of data from the
receive buffer to the transmit buffer by simply transferring
the descriptor from the receive queue to the transmit
queue.
The buffer management design has the following goals:
te
— simplicity,
— efficient use of the PCI bus (the overhead of the buffer
management technique is minimal),
— low CPU utilization,
— flexibility.
The format of the descriptors allows the packets to be Descriptors may be either per-packet or per-packetsaved in a number of configurations. A packet can be fragment. Each descriptor may describe one packet
stored in memory with a single descriptor and a single fragment. Receive and transmit descriptors are
packet fragment, or multiple descriptors each with a single symmetrical.
fragment. This flexibility allows the user to configure the 5.1.1 Descriptor Format
DP83815 to maximize efficiency. Architecture of the
specific system’s buffer memory, as well as the nature of DP83815 uses a symmetrical format for transmit and
network traffic, will determine the most suitable receive descriptors. In bridging and switching applications
this symmetry allows software to forward packets by simply
configuration of packet descriptors and fragments.
moving the list of descriptors that describe a single
received packet from the receive list of one MAC to the
transmit list of another. Descriptors must be aligned on an
even long word (32-bit) boundary.
Table 5-1 DP83815 Descriptor Format
Tag
0000h
link
0004h
cmdsts
0008h
bufptr
Description
ol
e
Offset
32-bit "link" field to the next descriptor in the linked list. Bits 1-0 must be 0, as
descriptors must be aligned on 32-bit boundaries.
32-bit Command/Status Field (bit-encoded).
32-bit pointer to the first fragment or buffer. In transmit descriptors, the buffer can
begin on any byte boundary. In receive descriptors, the buffer must be aligned on a
32-bit boundary.
bs
The original DP83810A Descriptor format supported
multiple fragments per descriptor. DP83815 only supports
a single fragment per descriptor. By default, DP83815 will
use the descriptor format shown above. By setting
CFG:EUPHCOMP, software may force compatibility with
the previous DP83810A Descriptor format (although still
only single fragment descriptors are supported). When
CFG:EUPHCOMP is set, then bufptr is at offset 0Ch, and
the 32-bit bufcnt field at offset 08h is ignored.
Some of the bit definitions in the cmdsts field are common
to both receive and transmit descriptors:
Table 5-2 cmdsts Common Bit Definitions
Bit
Tag
Description
Usage
OWN
Descriptor Ownership
Set to 1 by the data producer of the descriptor to transfer
ownership to the data consumer of the descriptor. Set to 0 by the
data consumer of the descriptor to return ownership to the data
producer of the descriptor. For transmit descriptors, the driver is
the data producer, and the DP83815 is the data consumer. For
receive descriptors, the DP83815 is the data producer, and the
driver is the data consumer.
30
MORE
More descriptors
Set to 1 to indicate that this is NOT the last descriptor in a packet
(there are MORE to follow). When 0, this descriptor is the last
descriptor in a packet. Completion status bits are only valid when
this bit is zero.
29
INTR
Interrupt
Set to 1 by software to request a “descriptor interrupt" when
DP83815 transfers the ownership of this descriptor back to
software.
28
SUPCRC
Suppress CRC /
Include CRC
In transmit descriptors, this indicates that CRC should not be
appended by the MAC. On receives, this bit is always set, as the
CRC is always copied to the end of the buffer by the hardware.
O
31
INCCRC
79
www.national.com
DP83815
5.0 Buffer Management
27
OK
26-16
---
Packet OK
The usage of these bits differ in receive and transmit descriptors.
See below for details.
15-12
11-0
In the last descriptor in a packet, this bit indicates that the packet
was either sent or received successfully.
(reserved)
SIZE
Descriptor Byte Count
Set to the size in bytes of the data.
Table 5-3 Transmit Status Bit Definitions
Tag
Description
Usage
26
TXA
Transmit Abort
Transmission of this packet was aborted.
25
TFU
Transmit FIFO
Underrun
Transmit FIFO was exhausted during the transmission of this
packet.
24
CRS
Carrier Sense Lost
Carrier was lost during the transmission of this packet. This
condition is not reported if TXCFG:CSI is set.
23
TD
Transmit Deferred
Transmission of this packet was deferred.
22
ED
Excessive Deferral
The length of deferral during the transmission of this packet was
excessive (> 3.2 ms), indicating transmission failure.
21
OWC
Out of Window
Collision
The MAC encountered an "out of window" collision during the
transmission of this packet.
20
EC
Excessive Collisions
The number of collisions during the transmission of this packet
was excessive, indicating transmission failure.
ol
e
te
Bit
If TXCFG register ECRETRY=0, this bit is set after 16 collisions.
If TXCFG register ECRETRY=1, this bit is set after 4 Excessive
Collision events (64 collisions).
19-16
CCNT
Collision Count
If TXCFG register ECRETRY=0, this field indicates the number of
collisions encountered during the transmission of this packet.
bs
If TXCFG register ECRETRY=1,
CCNT[3:2] = Excessive Collisions (0-3)
CCNT[1] = Multiple Collisions
O
CCNT[0] = Single Collision
Note that Excessive Collisions indicate 16 attempts failed, while
multiple and single collisions indicate collisions in addition to any
excessive collisions. For example a collision count of 33 includes
2 Excessive Collisions and will also set the Single Collision bit.
80
www.national.com
DP83815
5.0 Buffer Management (Continued)
DP83815
5.0 Buffer Management (Continued)
Table 5-4 Receive Status Bit Definitions
Bit
Tag
26
RXA
Receive Aborted
Description
Set to 1 by DP83815 when the receive was aborted, the value of
this bit always equals RXO. Exists for backward compatibility.
Usage
25
RXO
Receive Overrun
Set to 1 by DP83815 to indicate that a receive overrun condition
occurred. RXA will also be set.
24-23
DEST
Destination Class
When the receive filter is enabled, these bits will indicate the
destination address class as follows:
00 - Packet was rejected
01 - Destination is a Unicast address
10 - Destination is a Multicast address
11 - Destination is a Broadcast address
te
If the Receive Filter is enabled, 00 indicates that the packet was
rejected. Normally packets that are rejected do not cause any bus
activity, nor do they consume receive descriptors. However, this
condition could occur if the packet is rejected by the Receive Filter
later in the packet than the receive drain threshold
(RXCFG:DRTH).
Note: The DEST bits may not represent a correct DA class for runt
packets received with less than 6 bytes.
LONG
Too Long Packet
Received
If RXCFG:ALP=0, this flag indicates that the size of the receive
packet exceeded 1518 bytes.
ol
e
22
If RXCFG:ALP=1, this flag indicates that the size of the receive
packet exceeded 2046 bytes.
21
RUNT
20
ISE
19
CRCE
18
FAE
Frame Alignment Error The packet did not contain an integral number of octets.
17
LBP
Loopback Packet
Invalid Symbol Error
(100 Mb/s only) An invalid symbol was encountered during the
reception of this packet.
CRC Error
The CRC appended to the end of this packet was invalid.
The packet is the result of a loopback transmission.
bs
16
Runt Packet Received The size of the receive packet was less than 64 bytes (inc. CRC).
COL
Collision Activity
The receive packet had a collision during reception.
5.1.2 Single Descriptor Packets
To represent a packet in a single descriptor, the MORE bit in the cmdsts field is set to 0.
O
single descriptor / single fragment
link
64
0
ptr
MAC hdr
netwk hdr
data
Figure 5-1 Single Descriptor Packets
81
www.national.com
5.1.3 Multiple Descriptor Packets
5.1.4 Descriptor Lists
A single packet may also cross descriptor boundaries. This
is indicated by setting the MORE bit in all descriptors
except the last one in the packet. Ethernet applications
(bridges, switches, routers, etc.) can optimize memory
utilization by using a single small buffer per receive
descriptor, and allowing the DP83815 hardware to use the
minimum number of buffers necessary to store an
incoming packet.
Descriptors are organized in linked lists using the link field.
The system designer may also choose to implement a
"ring" of descriptors by linking the last descriptor in the list
back to the first. A list of descriptors may represent any
number of packets or packet fragments.
multiple descriptor / single fragment
link
link
14
1
link
20
1
ptr
MAC hdr
netwk hdr
30
ptr
te
ptr
0
data
ol
e
Figure 5-2 Multiple Descriptor Packets
Descriptors Organized in a Ring
addr 10100
addr 10180
10180
addr 101C0
101C0
bs
10140
addr 10140
10100
Descriptors Organized in a Linked List
addr 10100
O
10140
Subject to change without notice.
addr 10140
10180
addr 10180
addr 101C0
101C0
00000
Figure 5-3 List and Ring Descriptor Organization
82
Rev O
www.national.com
DP83815
5.0 Buffer Management (Continued)
DP83815
5.0 Buffer Management (Continued)
5.2 Transmit Architecture
The following figure illustrates the transmit architecture of the DP83815 10/100 Ethernet Controller.
Software/Memory
Hardware
Current Tx Desc Ptr
Transmit Descriptor
TxHead
link
cmdsts
ptr
Tx Desc Cache
link
cmdsts
ptr
Packet
te
Tx Data FIFO
Tx DMA
Figure 5-4 Transmit Architecture
5.2.1 Transmit State Machine
ol
e
When the CR:TXE bit is set to 1 (regardless of the current state), and the DP83815 transmitter is idle, then DP83815 will
read the contents of the current transmit descriptor into the TxDescCache. The DP83815’s TxDescCache can hold a
single fragment pointer/count combination.
The transmit state machine has the following states:
The transmit state machine is idle.
txDescRefr
Waiting for the "refresh" transfer of the link field of a completed descriptor from the PCI bus.
txDescRead
Waiting for the transfer of a complete descriptor from the PCI bus into the
TxDescriptorCache.
txFifoBlock
Waiting for free space in the TxDataFIFO to reach TxFillThreshold.
txFragRead
Waiting for the transfer of a fragment (or portion of a fragment) from the PCI bus to the
TxDataFIFO.
txDescWrite
Waiting for the completion of the write of the cmdsts field of an intermediate transmit
descriptor (cmdsts.MORE == 1) to host memory.
txAdvance
(transitory state) Examine the link field of the current descriptor and advance to the next
descriptor if link is not NULL.
bs
txIdle
O
The transmit state machine manipulates the following internal data spaces:
TXDP
A 32-bit register that points to the current transmit descriptor.
CTDD
An internal bit flag that is set when the current transmit descriptor has been completed, and
ownership has been returned to the driver. It is cleared whenever TXDP is loaded with a
new value (either by the state machine, or the driver).
TxDescCache
An internal data space equal to the size of the maximum transmit descriptor supported.
descCnt
Count of bytes remaining in the current descriptor.
fragPtr
Pointer to the next unread byte in the current fragment.
txFifoCnt
Current amount of data in the txDataFifo in bytes.
txFifoAvail
Current amount of free space in the txDataFifo in bytes (size of the txDataFifo - txFifoCnt).
Inputs to the transmit state machine include the following events:
CR:TXE
Driver asserts the TXE bit in the command register (similar to SONIC).
XferDone
Completion of a PCI bus transfer request.
FifoAvail
TxFifoAvail is greater than TxFillThreshold.
Subject to change without notice.
83
Rev O
www.national.com
DP83815
5.0 Buffer Management (Continued)
Table 5-5 Transmit State Tables
State
Event
Next State
txIdle
CR:TXE && !CTDD
txDescRead
Start a burst transfer at address TXDP and a length
derived from TXCFG.
CR:TXE && CTDD
txDescRefr
Start a burst transfer to refresh the link field of the current
descriptor.
txDescRefr
XferDone
txAdvance
txDescRead
XferDone && OWN
txFIFOblock
XferDone && !OWN
txIdle
FifoAvail
txFragRead
txFIFOblock
Actions
Set ISR:TXIDLE.
Start a burst transfer into the TxDataFIFO from fragPtr.
The length will be the minimum of txFifoAvail and
descCnt.
Decrement descCnt accordingly.
txDescWrite
(descCnt == 0) &&
!MORE
txAdvance
txFragRead
XferDone
txFIFOblock
txDescWrite
XferDone
txAdvance
txAdvance
link != NULL
txDescRead
link == NULL
txIdle
Start a burst transfer to write the status back to the
descriptor, clearing the OWN bit.
te
(descCnt == 0) &&
MORE
Write the value of TXDP to the txDataFIFO as a handle.
ol
e
TXDP <- txDescCache.link. Clear CTDD. Start a burst
transfer at address TXDP with a length derived from
TXCFG.
Set CTDD. Set ISR:TXIDLE. Clear CR:TXE.
CR:TXE && CTDD
CR:TXE && !CTDD
bs
txDescRefr
XferDone
txIdle
XferDone && !OWN
link = NULL
O
link != NULL
txAdvance
txDescRead
descCnt == 0 && !(cmdsts & MORE)
XferDone && OWN
XferDone
FifoAvail
txDescWrite
txFifoBlock
descCnt == 0 && (cmdsts & MORE)
txFragRead
XferDone
Figure 5-5 Transmit State Diagram
84
www.national.com
5.2.2 Transmit Data Flow
O
bs
ol
e
1. The device driver receives packets from an upper
layer.
2. An available DP83815 transmit descriptor is
allocated. The fragment information is copied from
the NOS specific data structure(s) to the DP83815
transmit descriptor.
3. The driver adds this descriptor to it’s internal list of
transmit descriptors awaiting transmission.
4. If the internal list was empty (this descriptor
represents the only outstanding transmit packet),
then the driver must set the TXDP register to the
address of this descriptor, else the driver will append
this descriptor to the end of the list.
5. The driver sets the TXE bit in the CR register to insure
that the transmit state machine is active.
6. If idle, the transmit state machine reads the descriptor
into the TxDescriptorCache.
7. The state machine then moves through the fragment
described within the descriptor, filling the TxDataFifo
with data. The hardware handles all aspects of byte
alignment; no alignment is assumed. Fragments
may start and/or end on any byte address. The
transmit state machine uses the fragment pointer
and the SIZE field from the cmdsts field of the current
descriptor to keep the TxDataFifo full. It also uses the
MORE bit and the SIZE field from the cmdsts field of
the current descriptor to know when packet
boundaries occur.
8. When a packet has completed transmission
(successful or unsuccessful), the state machine
updates the upper half of the cmdsts field of the
current descriptor in main memory, relinquishing
ownership, and indicating the packet completion
status. This update is done by a bus master
transaction that transfers only the upper 2 bytes to
the descriptor being updated. If more than one
descriptor was used to describe the packet, then
completion status is updated only in the last
descriptor. Intermediate descriptors only have the
OWN bits modified.
9. If the link field of the descriptor is non-zero, the state
machine advances to the next descriptor and
continues.
10. If the link field is NULL, the transmit state machine
suspends, waiting for the TXE bit in the CR register
to be set. If the TXDP register is written to, the CTDD
flag will be cleared. When the TXE bit is set, the state
machine will examine CTDD. If CTDD is set, the
state machine will "refresh" the link field of the
current descriptor. It will then follow the link field to
any new descriptors that have been added to the end
of the list. If CTDD is clear (implying that TXDP has
been written to), the state machine will start by
reading in the descriptor pointed to by TXDP.
te
In the DP83815 transmit architecture, packet transmission
involves the following steps:
Subject to change without notice.
85
Rev O
www.national.com
DP83815
5.0 Buffer Management (Continued)
5.3 Receive Architecture
packets. When the amount of receive data in the
RxDataFIFO is more than the RxDrainThreshold, or the
RxDataFIFO contains a complete packet, then the state
machine begins filling received buffers in host memory.
The receive architecture is as "symmetrical" to the transmit
architecture as possible. The receive buffer manager
prefetches receive descriptors to prepare for incoming
Software/Memory
Hardware
Receive Descriptor List
link
cmdsts
ptr
link
cmdsts
ptr
RxHead
link
cmdsts
ptr
link
cmdsts
ptr
Rx Descriptor Cache
Rx Data FIFO
te
Rx DMA
Figure 5-6 Receive Architecture
5.3.1 Receive State Machine
read an entire descriptor in a single burst, and reduces the
number of bus accesses required for fragment information
to 1. The DP83815 Rx Descriptor Cache holds a single
buffer pointer/count combination.
ol
e
When the RXE bit is set to 1 in the CR register (regardless
of the current state), and the DP83815 receive state
machine is idle, then DP83815 will read the contents of the
descriptor referenced by RXDP into the Rx Descriptor
Cache. The Rx Descriptor Cache allows the DP83815 to
The receive state machine has the following states:
The receive state machine is idle.
rxDescRefr
Waiting for the "refresh" transfer of the link field of a completed descriptor from the PCI bus.
rxDescRead
Waiting for the transfer of a descriptor from the PCI bus into the RxDescCache.
rxFifoBlock
Waiting for the amount of data in the RxDataFifo to reach the RxDrainThreshold or to represent a
complete packet.
rxFragWrite
Waiting for the transfer of data from the RxDataFIFO via the PCI bus to host memory.
rxDescWrite
Waiting for the completion of the write of the cmdsts field of a receive descriptor.
bs
rxIdle
The receive state machine manipulates the following internal data spaces:
RXDP
An internal bit flag that is set when the current receive descriptor has been completed, and ownership
has been returned to the driver. It is cleared whenever RXDP is loaded with a new value (either by the
state machine, or the driver).
O
CRDD
A 32-bit register that points to the current receive descriptor.
RxDescCache An internal data space equal to the size of the maximum receive descriptor supported.
descCnt
Count of bytes available for storing receive data in all fragments described by the current descriptor.
fragPtr
Pointer to the next unwritten byte in the current fragment.
rxPktCnt
Number of packets in the rxDataFifo. Incremented by the MAC (the fill side of the FIFO). Decremented
by the receive state machine as packets are processed.
rxPktBytes
Number of bytes in the current packet being drained from the rxDataFifo, that are in fact currently in the
rxDataFifo (Note: packets larger than FIFO size, this number will never be greater than the FIFO size).
Inputs to the receive state machine include the following events:
CR:RXE
The RXE bit in the Command Register has been set.
XferDone
completion of a PCI bus transfer request.
FifoReady
(rxPktCnt > 0) or (rxPktBytes > rxDrainThreshold)... in other words, if we have a complete packet in the
FIFO (regardless of size), or the number of bytes that we do have is greater than the rxDrainThreshold,
then we are ready to begin draining the rxDataFifo.
Subject to change without notice.
86
Rev O
www.national.com
DP83815
5.0 Buffer Management (Continued)
DP83815
5.0 Buffer Management (Continued)
Table 5-6 Receive State Tables
State
Event
Next State
rxIdle
CR:RXE && !CRDD
rxDescRead
Start a burst transfer at address RXDP and a length
derived from RXCFG.
CR:RXE && CRDD
rxDescRefr
Start a burst transfer to refresh the link field of the current
descriptor.
rxDescRefr
XferDone
rxAdvance
rxDescRead
XferDone && !OWN
rxFIFOblock
XferDone && OWN
rxIdle
FifoReady
rxFragWrite
Start a burst transfer from the RxDataFIFO to host
memory at fragPtr. The length will be the minimum of
rxPktBytes and descCnt. Decrement descCnt
accordingly.
(descCnt == 0) &&
(rxPktBytes > 0)
rxDescWrite
Start a burst transfer to write the status back to the
descriptor, setting the OWN bit, and setting the MORE
bit. We'll continue the packet in the next descriptor.
rxPktBytes == 0
rxDescWrite
rxFragWrite
XferDone
rxFIFOblock
rxDescWrite
XferDone
rxAdvance
rxAdvance
link!= NULL
rxDescRead
link == NULL
rxIdle
te
Set ISR:RXIDLE.
ol
e
Start a transfer to write the cmdsts back to the descriptor,
setting the OWN bit and clearing the MORE bit, and
filling in the final receive status (CRC, FAE, SIZE, etc.).
RXDP <- rxDescCache.link. Clear CRDD. Start a burst
transfer at address RXDP with a length derived from
RXCFG:MXDMA.
Set CRDD. Set ISR:RXIDLE.
O
bs
rxFIFOblock
Actions
87
www.national.com
DP83815
5.0 Buffer Management (Continued)
CR:RXE && CRDD
rxDescRefr
CR:RXE && !CRDD
XferDone
rxIdle
XferDone && OWN
link = NULL
link != NULL
rxDescRead
te
rxAdvance
XferDone && !OWN
XferDone
ol
e
rxPktBytes == 0
FifoReady
rxDescWrite
rxFifoBlock
(descCnt == 0) && (rxPktBytes > 0)
rxFragWrite
XferDone
Figure 5-7 Receive State Diagram
bs
5.3.2 Receive Data Flow
O
With a bus mastering architecture, some number of buffers
and descriptors for received packets must be pre-allocated
when the DP83815 is initialized. The number allocated will
directly affect the system's tolerance to interrupt latency.
The more buffers that you pre-allocate, the longer the
system will survive an incoming burst without losing
receive packets, if receive descriptor processing is delayed
or preempted. Buffers sizes should be allocated in 32 byte
multiples.
1. Prior to packet reception, receive buffers must be
described in a receive descriptor list (or ring, if
preferred). In each descriptor, the driver assigns
ownership to the hardware by clearing the OWN bit.
Receive descriptors may describe a single buffer.
2. The address of the first descriptor in this list is then
written to the RXDP register. As packets arrive, they
are placed in available buffers. A single packet may
occupy one or more receive descriptors, as required
by the application.The device reads in the first
descriptor into the RxDescCache.
Subject to change without notice.
3. As data arrives in the RxDataFIFO, the receive buffer
management state machine places the data in the
receive buffer described by the descriptor. This
continues until either the end of packet is reached, or
the descriptor byte count for this descriptor is
reached.
4. If end of packet was reached, the status in the
descriptor (in main memory) is updated by setting the
OWN bit and clearing the MORE bit, by updating the
receive status bits as indicated by the MAC, and by
updating the SIZE field. The status bits in cmdsts are
only valid in the last descriptor of a packet (with the
MORE bit clear). Also for the last descriptor of a
packet, the SIZE field will be updated to reflect the
actual amount of data written to the buffer (which
may be less the full buffer size allocated by the
descriptor).
If the receive buffer management state machine runs out of
descriptors while receiving a packet, data will buffer in the
receive FIFO. If the FIFO overflows, the driver will be
interrupted with an RxOVR error.
88
Rev O
www.national.com
6.1 Introduction
• Magic Packet: “A specific packet of information sent
to remotely wake up a sleeping or powered off PC on
a network, it is handled in the LAN controller. The
Magic Packet must contain a specific data sequence which can be located anywhere within the
packet but must be preceded by a synchronization
stream. The packet must also meet the basic requirements for the LAN technology chosen (e.g. ethernet
frame). The specific data sequence consists of 16 duplications of the MAC address of the machine to be
awakened. The synchronization stream is defined as
6 bytes of FFh.”
• ACPI-compatible operating system - An operating
system that takes advantage of the PCI Power Management interface. These include Windows 98 (when
installed with ACPI), Windows 2000, and Windows
ME (when installed with ACPI).
The DP83815 supports Wake-On-LAN (WOL) and the PCI
Power Management Specification version 1.1. These
features allow the device to enter a power saving mode,
and to signal the system to return to a normal operating
state when a wake event occurs. This section describes
the power management operation on the DP83815.
6.2 Definitions (for this document only)
te
6.3 Packet Filtering
When the PME Enable bit is set to 1, incoming packets are
filtered based on settings in the Receive Filter Control
Register (RFCR - offset 48h in operational registers) and
the Wake Command/Status Register (WCSR - offset 40h in
operational registers). In other words, a packet must pass
both filters to be accepted. This is a desirable feature in
WOL mode since it prevents non-wake packets from filling
the receive FIFO. However, it is not desirable in normal
operating mode since it will not allow non-wake packets
from being received. Therefore, the driver should ensure
that the PME Enable bit is set to 0 for normal operation.
ol
e
• Power Management - a PCI specification that defines
power-saving states of PCI devices and systems. A
spec-compliant device implements two PCI Configuration registers to control and report status for its
Power Management function.
• Wake event - An event that causes a PCI device in
Power Management mode to signal the system.
• PME Enable (PMEEN) - bit 8 of the Power Management Control/Status Register (PMCSR - offset 44h in
the PCI configuration space). Setting this bit to 1 allows the device to assert the PMEN pin when it detects a wake event.
• Sleep mode - A device is in sleep mode if it is programmed to a Power Management state other than
the fully operational state and is not allowed to signal
a wake event to the system. In this mode, the PME
Enable bit is 0.
• Wake-On-LAN mode - A device is in Wake-On-LAN
(WOL) mode if it is programmed to a Power Management state other than the fully operational state and is
allowed to signal a wake event to the system. In this
mode, the PME Enable bit is 1.
• PMEN (pin59) - this pin is similar in function to a system interrupt (INTAN pin). When asserted, it signals
the system that a wake event has occurred.
• PME Status - bit 15 of PMCSR. When 1, indicates the
device detected a wake event. If PME Enable is also
set to 1, the device will assert PMEN whenever PME
Status is 1. Software writes a 1 to this bit to clear it.
bs
6.4 Power Management
The Power Management Specification presents a low-level
hardware interface to PCI devices for the purpose of
saving power. The DP83815 supports power states D0,
D1, D2, D3hot, and D3cold as defined in the PCI Power
Management Specification. These states provide
increasing power reduction in the order they are listed.
Table 6-1 lists the different Power Management modes and
the methods of power reduction in DP83815 devices.
Table 6-1 Power Management Modes
PME Enable
(PMEEN)
O
Power State
Wake
Conditions
Power Management
Mode
PCICLK
Physical Layer
Cell
D0
(SW sets to 0)
Unconfigured
Normal
On
On
D1
Don’t Care
Don’t Care
WOL
On
On
D2
Don’t Care
Don’t Care
WOL
May be Off
On
D3hot
Off
Don’t Care
Sleep
May be Off
Off
D3hot
Don’t Care
Unconfigured
Sleep
May be Off
Off
D3hot
On
Configured
WOL
May be Off
On
D3cold
Off
Don’t Care
Sleep
Off
Off
D3cold
Don’t Care
Unconfigured
Sleep
Off
Off
D3cold
On
Configured
WOL
Off
On
89
www.national.com
DP83815
6.0 Power Management and Wake-On-LAN
6.4.1 D0 State
6.5.1 Entering WOL Mode
The D0 state is the normal operational state of the device.
The PME Enable bit should be set to 0 to prevent packet
filtering based on the settings in the Wake Control/Status
Register (WCSR). It is also advisable to turn off all WOL
conditions in WCSR to prevent unnecessary PME
interrupts.
The following steps are required to place the DP83815 into
WOL mode:
1. Disable the receiver by writing a 1 to the Receiver Disable bit 3 (RXD) in the Command Register (CR - offset
00h in operational registers).
2. Write 0 to the Receive Descriptor Pointer Register
(RXDP - offset 30h in operational registers) to reset
the receive pointer.
3. Enable the receiver (now in “silent receive” mode) by
writing a 1 to the Receiver Enable bit 2 in the Command Register (CR:RXE).
4. Configure the Receive Filter Control Register (RFCR)
to enable the receive filter (RFCR:RFEN - bit 31) and
accept the desired type of wakeup packets. Note that
the Receive Filter Enable bit must be set to 1 for Wake
on PHY Interrupt as well.
5. If Wake on PHY Interrupt is desired, additionally configure registers MICR (offset C4h in operational registers) and MISR (offset C8h in operational registers).
6. Configure the Wake Command/Status Register
(WCSR) with the desired type of wake events. An
ACPI-compatible operating system should notify the
driver of these events.
7. Write a 1 to PME Enable, and set the desired Power
State in PMCSR. These can be done in one operation,
or PME Enable can be written first. An ACPI-compatible operating system should handle this step.
8. If the Power Management state is D3cold, the system
will assert PCI reset, stop the PCI clock, and remove
power from the PCI bus.
The following two examples show the corresponding
register settings for Wake on Magic Packet mode and
Wake on PHY Interrupt mode respectively:
The D1 state is the least power-saving Power Management
state, and might not be used by the operating system. The
device will only respond to PCI configuration transactions
and therefore will not transmit data. The only bus activity
the device can initiate is the assertion of the PMEN pin
(assuming the PME Enable bit is set to 1); no DMA activity
or interrupts will occur. The device will continue to receive
packets up to the limit of the receive FIFO size. Upon
returning to the D0 state, the system must re-enable I/O
and memory space in the device and turn on bus master
capability.
6.4.3 D2 State
6.4.4 D3hot State
ol
e
The D2 state has the same features as the D1 state, and
the system may turn off the PCI clock, further reducing
power. The device will continue to receive packets up to
the limit of the receive FIFO size. Like the D1 state, the D2
state might not be used by the operating system.
te
6.4.2 D1 State
bs
The D3hot state is often known as the Standby state. If the
PME Enable bit is 0, or WOL is unconfigured, the device
saves power by turning off the Physical Layer Cell (PHY).
The system may turn off the PCI clock. In order to receive
packets in the D3hot state, both WOL mode and PME
Enable must be turned on. Like the D2 and D1 states, the
device will respond to PCI configuration transactions as
long as the PCI clock is running.
When the device exits the D3hot state, all PCI
configuration registers except for the PME Enable and
PME Status bits are reset to their default values. This
means the operating system must reinitialize the device’s
PCI configuration registers with valid base addresses, etc.
If PME Enable or WOL mode were not turned on, the
device must be fully reinitialized.
Entering Wake on Magic Packet mode:
O
CR = 00000008h (disable the receiver)
RXDP = 00000000h (reset the receive pointer)
CR = 00000004h (enable the receiver)
RFCR = F0000000h (enables the receive filter and
allows Broadcast, Multicast and Unicast packets to be
received - a Magic Packet could be any of those.)
6.4.5 D3cold State
The D3cold state is the highest power-saving state; it is 5. WCSR = 00000200h (sets the Wake on Magic
Packet bit)
often known as the Hibernate state. The PCI bus is turned
off, as is the PCI clock. If the PME Enable bit or WOL is 6. PMCSR = 00008103h (clears the PME status bit 15,
sets the PME Enable bit 8 and sets the Power State
turned off, the PHY is turned off. This allows the device to
consume the least amount of power. The device must be
bits [1:0] to D3hot)
fully reinitialized after exiting this mode.
Entering Wake on PHY Interrupt mode:
6.5 Wake-On-LAN (WOL) Mode
Wake-On-LAN Mode is a system-level function that allows
a network device to alert the system that a wake event has
occurred. It works in conjunction with the PCI Power
Management states detailed in the previous section. The
DP83815 supports several wake events including, but not
limited to, Wake on PHY Interrupt (i.e. link change), Wake
on Magic Packet, and Wake on Pattern Match. The
supported wake events appear in the device’s Wake
Command/Status Register (WCSR).
Subject to change without notice.
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
8.
90
CR = 00000008h (disable the receiver)
RXDP = 00000000h (reset the receive pointer)
CR = 00000004h (enable the receiver)
RFCR = 80000000h (enables the receive filter)
MICR = 00000002h (sets the Interrupt Enable bit 1)
MISR = 00000000h (unmasks the change of link status event)
WCSR = 00000001h (sets the Wake on PHY interrupt
bit)
PMCSR = 00008103h (clears the PME status bit 15,
sets the PME Enable bit 8 and sets the Power State
bits [1:0] to D3hot)
Rev O
www.national.com
DP83815
6.0 Power Management and Wake-On-LAN (Continued)
6.5.2 Wake Events
6.6 Sleep Mode
If the device detects a wake event while in WOL mode, it
will assert the PMEN pin low to signal the system that a
wake event has occurred. The system should then bring
the device out of WOL mode as described below.
Sleep Mode is a system-level function that allows a device
to be placed in a lower power mode than WOL mode. In
sleep mode, the device will not be able to detect wake
events or signal the system that it needs service.
6.5.3 Exiting WOL Mode
6.6.1 Entering Sleep Mode
The following steps are required to bring the device out of
WOL mode (with or without an accompanying wake event):
The following steps are required to enter Sleep Mode:
1.
1.
2.
3.
te
4.
5.
Disable the receiver by writing a 1 to the Receiver Disable bit in the Command Register (CR:RXD).
Write 0 to the Receive Descriptor Pointer Register
(RXDP)
Force the receiver to reread the descriptor pointer by
writing a 1 to the Receiver Enable bit in the Command
Register (CR:RXE).
Do not configure any wake events in WCSR.
Write a 0 to PME Enable, and set the desired Power
State in PMCSR. These can be done in one operation.
An ACPI-compatible operating system should handle
this step.
If the Power Management state is D3cold, the system
will assert PCI reset, stop the PCI clock, and remove
power from the PCI bus.
6.
O
bs
ol
e
If the Power Management state is D3cold, the system
will assert PCI reset, restore PCI bus power, and
restart the PCI clock. This will also return the Power
State to D0. The PCI configuration registers (i.e. base
addresses, bus master enable, etc.) must be reinitialized.
2. Write a 0 to Power State bits [0:1] in the PMCSR (in
case the WOL Power State was not D3hot or D3cold)
and PME Enable. These can be done in one operation, or Power State can be written first. Turning off
PME Enable will cause the device to de-assert the
PMEN pin, if it was asserted.
3. If the WOL Power State was D3hot or D3cold, reinitialize the PCI configuration registers (i.e. base
addresses, bus master enable, etc.). An ACPI-compatible operating system should handle this step. Note
that operational registers will not be accessible until
this step is completed.
4. If a wake event occurred, read the WCSR to determine what the event was.
5. Write a 1 to PME Status. This will clear any wake
event in the device. An ACPI-compatible operating
system will perform this write to the PMCSR; a driver
can perform this write using the Clockrun Control/Status Register (CCSR).
6. If the wake event was a PHY interrupt from an internal
PHY, clear the event in the PHY registers. Refer to the
MISR in Section 4.3.11.
7. Clear all bits in WCSR.
8. Disable the receiver by writing a 1 to the Receiver Disable bit in the Command Register (CR:RXD).
9. Reconfigure RFCR as appropriate for normal operation.
10. Write a valid receive descriptor pointer to the Receive
Descriptor Pointer Register (RXDP)
11. Enable the receiver by writing a 1 to the Receiver
Enable bit in the Command Register (CR:RXE). If the
wake event was a packet, this will now be emptied
from the receive FIFO via DMA.
6.6.2 Exiting Sleep Mode
The following steps are required to bring the DP83815 out
of Sleep Mode:
1.
2.
3.
4.
5.
6.
If the Power Management state is D3cold, the system
will assert PCI reset, restore PCI bus power, and
restart the PCI clock. This will also return the Power
State to D0. The PCI configuration registers (i.e. base
addresses, bus master enable, etc.) must be reinitialized.
Write a 0 to Power State bits [0:1] in the PMCSR (in
case the sleep Power State was not D3hot or D3cold).
If the sleep Power State was D3hot or D3cold, reinitialize the PCI configuration registers (i.e. base
addresses, bus master enable, etc.). An ACPI-compatible operating system should handle this step. Note
that operational registers will not be accessible until
this step is completed.
Disable the receiver by writing a 1 to the Receiver Disable bit in the Command Register (CR:RXD).
Write a valid receive descriptor pointer to the Receive
Descriptor Pointer Register (RXDP)
Enable the receiver by writing a 1 to the Receiver
Enable bit in the Command Register (CR:RXE).
6.7 Pin Configuration for Power Management
Refer to Table 6-2 for proper pin connection for power
management configuration:
Table 6-2 PM Pin Configuration
Pin Name
PMEN
3VAUX
PWRGOOD
Pin No. Power Mgt No Power Mgt
59
*PME#
3.3V
122
*3.3Vaux
GND
123
3.3V
3.3V
Note 3: *Refer to Demo Board schematics for additional information.
Subject to change without notice.
91
Rev O
www.national.com
DP83815
6.0 Power Management and Wake-On-LAN (Continued)
Absolute Maximum Ratings
Supply Voltage (VDD)
-0.5 V to 3.6 V
3.3 V PCI signaling, 5.0 V tolerant
DC Input Voltage (VIN)
-0.5 V to 7.0 V
DC Output Voltage (VOUT)
For LBGA Package:
θja (@0 cfm, 1 Watt)
Recommended Operating Conditions
Supply voltage (VDD)
-0.5 V to VDD + 0.5 V
Storage Temperature Range (TSTG)
220 °C
ESD Rating
2.0 KV
te
9.5 °C/W
7.1 DC Specifications
o
o
TA = 0 C to 70 C, VDD = 3.3 V ±0.3V, unless otherwise specified
Symbol
95 °C
Note: Absolute maximum ratings are values beyond which
operation is not recommended or guaranteed. Extended
exposure beyond these limits may affect device reliability.
They are not meant to imply that the device should be
operated at these limits.
44.5 °C/W
θjc (@1 Watt)
150 °C
Max. Case Temperature
(RZAP = 1.5kΩ, CZAP = 120 pF)
For LQFP Package:
θja (@0 cfm, 1 Watt)
0 to 70 °C
Max. Junction Temperature
743 mW
Body Temp. (TB) (Soldering, 10 sec)
3.3 Volts + 0.3V
Ambient Temperature (TA)
-65 °C to 150 °C
Power Dissipation (PD)
45 °C/W
Parameter
Conditions
Minimum High Level Output Voltage IOH = -6 mA
VOL
Maximum Low Level Output Voltage IOL = 6 mA,
Typ
Max
2.4
ol
e
VOH
Min
0.4
Units
V
V
IOL = 4 mA for LEDxxx,
PMEN/CLKRUNN
Minimum High Level Input Voltage
VIL
Maximum Low Level Input Voltage
IIN
Input Current
Nominal VDD
VIN = VDD or GND
bs
VIH
2.0
V
0.8
V
-10
10
µA
-10
10
µA
IOZ
TRI-STATE Output Leakage Current VOUT = VDD or GND
IDD
Operating Supply Current
IOUT = 0 mA, FREQ = FMAX
170
225
mA
WOL standby
See note1 below.
115
200
mA
10
20
mA
Sleep mode
Differential Input Resistance
O
RINdiff
RD+/−
1.1
kΩ
VTPTD_100
100 Mb/s Transmit Voltage
TD+/−
VTPTDsym
100 Mb/s Transmit Voltage
Symmetry
TD+/−
VTPTD_10
10 Mb/s Transmit Voltage
TD+/−
CIN
CMOS Input Capacitance
8
pF
CMOS Output Capacitance
8
pF
COUT
0.95
1.05
±2
2.2
SDTHon
100BASE-TX Signal detect turn-on
threshold
RD+/−
SDTHoff
100BASE-TX Signal detect turn-off
threshold
RD+/−
200
10BASE-T Receive Threshold
RD+/−
300
VTH1
1
2.5
V
%
2.8
1000
V
mV diff
pk-pk
mV diff
pk-pk
585
mV
Note1: IDD for WOL Standby Typ: typical is measured using a wake enabled D3Hot state. IDD for WOL Standby Max: maximum is measured using a wake
enabled D1 state.
92
www.national.com
DP83815
7.0 DC and AC Specifications
DP83815
7.0 DC and AC Specifications (Continued)
7.2 AC Specifications
7.2.1 PCI Clock Timing
T3
T1
PCICLK
Parameter
PCICLK Low Time
7.2.1.2
PCICLK High Time
7.2.1.3
PCICLK Cycle Time
7.2.2 X1 Clock Timing
Max
Units
12
ns
12
ns
30
∞
ns
ol
e
7.2.1.1
Min
te
Number
T2
T3
T1
T2
bs
X1
Number
Parameter
Min
Max
Units
X1 Low Time
16
ns
7.2.2.2
X1 High Time
16
ns
O
7.2.2.1
7.2.2.3
X1 Cycle Time
40
93
40
ns
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.3 Power On Reset (PCI Active)
Power Stable
T1
RSTN
T2
1st PCI Cycle
PCICLK
Number
Parameter
te
Reset Complete
Min
RSTN Active Duration from PCICLK
stable
7.2.3.2
Reset Disable to 1st PCI Cycle
1
Units
ms
ol
e
7.2.3.1
Max
EE Enabled
1500
us
EE Disabled
1
us
Note 1: Minimum reset complete time is a function of the PCI, transmit, and receive clock frequencies.
Note 2: Minimum access after reset is dependent on PCI clock frequency. Accesses to DP83815 during this period will be ignored.
Note 3: EE is disabled for non power on reset.
7.2.4 Non Power On Reset
bs
Output
T1
O
RSTN
Number
7.2.4.1
Parameter
1st PCI Cycle
Min
RSTN to Output Float
Max
Units
40
ns
Note 4: Minimum reset complete time is a function of the PCI, transmit, and receive clock frequencies.
94
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.5 POR PCI Inactive
VDD
T1
EESEL
T2
TPRD
7.2.5.1
Parameter
VDD stable to EE access
Min
Max
Units
te
Number
T3
60
us
2000
us
VDD indicates the digital supply (AUX
power plane, except PCI bus power.)
Guaranteed by design.
EE Configuration load duration
7.2.5.3
EE Cfg. load complete to RX ready:
ol
e
7.2.5.2
600
- Auto-Neg or 10 Mb
TBD
us
O
bs
- 100 Mb
95
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.6 PCI Bus Cycles
The following table parameters apply to ALL the PCI Bus Cycle Timing Diagrams contained in this section.
Number
Parameter
Min
Max
Units
7.2.6.1
Input Setup Time
7
ns
7.2.6.2
Input Hold Time
0
ns
7.2.6.3
Output Valid Delay
2
7.2.6.4
Output Float Delay (toff time)
7.2.6.5
Output Valid Delay for REQN - point to point
2
7.2.6.6
Input Setup Time for GNTN - point to point
10
AD[31:0]
T1 T2
Addr
T1 T2
C/BEN[3:0]
Cmd
T1
IRDYN
12
ns
ns
Data
T2
T1
BE
T2
T1
TRDYN
T3
T3
T1 T2
O
DEVSELN
ns
T4
T3
T3
bs
IDSEL
T2
28
ol
e
PCICLK
T2
ns
te
PCI Configuration Read
FRAMEN T1
11
T4
T3
T3
PAR
T4
T1
T4
T1
T2
PERRN
96
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
PCI Configuration Write
PCICLK
FRAMEN
AD[31:0]
T1
T1
T1
C/BEN[3:0]
T1
T2
T2
T2 T1
Addr
Data
T2 T1
Cmd
T2
T2
BE
IDSEL
T2
T4
te
T1
IRDYN
T3
TRDYN
T4
T3
DEVSELN
T1 T2
T2
ol
e
PAR
T4
T3
PERRN
PCI Bus Master Read
T4
bs
PCICLK
FRAMEN
T3
C/BEN[3:0]
T3
Cmd
O
AD[31:0]
T3
Addr
IRDYN
T3
T4
T1
T3
T1 T2
Data
T4
BE
T3
T3
T4
T2
T1
TRDYN
T1
T2
DEVSELN
T4
T3
T2
T1
PAR
T3
PERRN
97
T3
T4
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
PCI Bus Master Write
PCICLK
T3
T3
T3
Data
T4
AD[31:0]
T3
Addr
T3
Cmd
T3
T4
C/BEN[3:0]
FRAMEN
T4
BE
T3
T3
IRDYN
T2
T1
DEVSELN
T3
T3
T2
T4
ol
e
PAR
te
T1
TRDYN
T4
T1
PERRN
PCI Target Read
bs
PCICLK
FRAMEN T1
Addr
T1 T2
IRDYN
TRDYN
DEVSELN
T2
T4
T4
T3
T3
Data
T1
Cmd
O
C/BEN[3:0]
T4
T2
T1 T2
AD[31:0]
T2
T2
BE
T2
T1
T3
T3
T1 T2
T4
T4
T3
T3
PAR
T1
T4
T1
PERRN
98
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
PCI Target Write
PCICLK
FRAMEN
AD[31:0]
T1
T2
T1
T2
Addr
T1
C/BEN[3:0]
T2
T1
Data
T2 T1
Cmd
BE
T2
T1
IRDYN
T4
te
T3
TRDYN
T4
T3
DEVSELN
T1 T2
T2
ol
e
PAR
T3
PERRN
PCI Bus Master Burst Read
PCICLK
T3
bs
T3
FRAMEN
T3
Addr
C/BEN[3:0]
T3
Cmd
O
AD[31:0]
IRDYN
T4
T1
Data
T3
Data
BE
T3
T4
T4
T2
Data
T4
T4
T3
T2
T1
TRDYN
T1
T2
DEVSELN
T4
T3
T2
T1
PAR
T3
PERRN
99
T4
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
PCI Bus Master Burst Write
PCICLK
T3
T3
AD[31:0]
T3
Addr
T3
Data
C/BEN[3:0]
T3
Cmd
T3
T4
Data
Data
T4
BE
T3
T3
IRDYN
T1
T2
DEVSELN
T3
T4
ol
e
T3
T4
T2
T1
TRDYN
PAR
T4
te
FRAMEN
T1
PERRN
bs
PCI Bus Arbitration
T2
PCICLK
T5
T5
REQN
T6
T2
O
GNTN
100
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.7 EEPROM Auto-Load
T1
EECLK
T2
EESEL
T3
T4
EEDO
T6
EEDI
te
T5
Refer to FM93C46 data sheet
Number
Parameter
EECLK Cycle Time
7.2.7.2
Max
Units
4
us
EECLK Delay from EESEL Valid
1
us
7.2.7.3
EECLK Low to EESEL Invalid
2
us
7.2.7.4
EECLK to EEDO Valid
7.2.7.5
EEDI Setup Time to EECLK
2
us
7.2.7.6
EEDI Hold Time from EECLK
2
us
2
us
O
bs
ol
e
7.2.7.1
Min
101
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.8 Boot PROM/FLASH
T14
T13
T15
T16
MCSN
T5
T17
MRDN
T2
T3
T9
T4
MA[15:0]
T1
T6
te
MD[7:0]
T12
T8
T11
T10
ol
e
MWRN
T7
Number
Parameter
Min
Typ
7.2.8.1
Data Setup Time to MRDN Invalid
7.2.8.2
Address Setup Time to MRDN Valid
30
ns
7.2.8.3
Address Hold Time from MRDN Invalid
0
ns
7.2.8.4
Address Invalid from MWRN Valid
180
ns
7.2.8.5
MRDN Pulse Width
180
ns
bs
20
Units
ns
Data Hold Time from MRDN Invalid
7.2.8.7
Data Invalid from MWRN Invalid
60
ns
7.2.8.8
Data Valid to MWRN Valid
30
ns
7.2.8.9
Address Setup Time to MWRN Valid
30
ns
7.2.8.10
MRDN Invalid to MWRN Valid
7.2.8.11
MWRN Pulse Width
150
ns
7.2.8.12
Address/MRDN Cycle Time
210
ns
7.2.8.13
MCSN Valid to MRDN Valid
30
ns
7.2.8.14
MCSN Invalid to MRDN Invalid
0
ns
7.2.8.15
MCSN Valid to MWRN Valid
30
ns
7.2.8.16
MWRN Invalid to MCSN Invalid
30
ns
7.2.8.17
MCSN Valid to address Valid
0
ns
O
7.2.8.6
0
ns
150
ns
Note 5: T10 is guaranteed by design.
Note 6: Timings are based on a 30ns PCI clock period.
102
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.9 100BASE-TX Transmit
TPTD+/−
+1 FALL
+1 RISE
-1 FALL
-1 RISE
T2
Parameter
7.2.9.1
Description
100 Mb/s TPTD+/− Rise and
Fall Times
Notes
see Test Conditions section
bs
100 Mb/s Rise/Fall Mismatch
7.2.9.2
T1
T1
ol
e
TPTD+/−
eye pattern
T1
te
T1
100 Mb/s TPTD+/−
Transmit Jitter
Min
Typ
Max
Units
3
4
6
ns
500
ps
1.4
ns
Note: Normal Mismatch is the difference between the maximum and minimum of all rise and fall times.
Note: Rise and fall times taken at 10% and 90% of the +1 or -1 amplitude.
Note: Carrier Sense On Delay is determined by measuring the time from the first bit of the “J” code group to the assertion of Carrier Sense.
Note: 1 bit time = 10 ns in 100 Mb/s mode.
O
Note: The Ideal window recognition region is ± 4 ns.
103
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.10 10BASE-T Transmit End of Packet
0
0
1
1
T1
TPTD+/-
T2
TPTD+/-
7.2.10.1
Description
Notes
End of Packet High Time
(with ‘0’ ending bit)
7.2.10.2
Min
Typ
Max
te
Parameter
End of Packet High Time
10 Mb/s
300
ns
10 Mb/s
250
ns
ol
e
(with ‘1’ ending bit)
Units
7.2.11 10 Mb/s Jabber Timing
TXE(Internal)
T3
T2
bs
TPTD+/−
COL(Internal)
Parameter
O
7.2.11.1
Description
Jabber Activation Time
7.2.11.2
Jabber Deactivation Time
Notes
Min
Typ
Max
Units
10 Mb/s
85
ms
10 Mb/s
500
ms
104
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.12 10BASE-T Normal Link Pulse
T2
T1
Description
7.2.12.1
Pulse Width
7.2.12.2
Pulse Period
Notes
Note: These specifications represent both transmit and receive timings
Typ
Max
Units
100
ns
16
ms
ol
e
7.2.13 Auto-Negotiation Fast Link Pulse (FLP)
Min
te
Parameter
T2
T3
T1
Fast Link Pulse(s)
data
pulse
bs
clock
pulse
clock
pulse
T5
O
T4
Parameter
FLP Burst
FLP Burst
Description
Notes
Min
Typ
Max
Units
7.2.13.1
Clock, Data Pulse Width
100
ns
7.2.13.2
Clock Pulse to Clock Pulse
Period
125
µs
7.2.13.3
Clock Pulse to Data Pulse
Period
62.5
µs
7.2.13.4
Burst Width
2
ms
7.2.13.5
FLP Burst to FLP Burst Period
16
ms
Data = 1
Note: These specifications represent both transmit and receive timings
105
www.national.com
DP83815
7.0 DC and AC Specifications (Continued)
7.2.14 Media Independent Interface (MII)
MDC
T1
MDIO(output)
T2
T3
MDIO(input)
RXCLK
T4
T5
T6
T7
RXDV,RXER
TXCLK
te
RXD[3:0]
TXD[3:0]
ol
e
T8
T9
TXEN
Min
Max
Units
7.2.14.1
MDC to MDIO Valid
Parameter
0
300
ns
7.2.14.2
MDIO to MDC Setup
10
10
ns
7.2.14.3
MDIO from MDC Hold
10
ns
7.2.14.4
RXD to RXCLK Setup
10
ns
7.2.14.5
RXD from RXCLK Hold
10
ns
O
bs
Number
7.2.14.6
RXDV, RXER to RXCLK Setup
10
ns
7.2.14.7
RXDV, RXER from RXCLK Hold
10
ns
7.2.14.8
TXCLK to TXD Valid
0
25
ns
7.2.14.9
TXCLK to TXEN Valid
0
25
ns
106
www.national.com
DP83815
ol
e
te
PHYSICAL DIMENSIONS inches (millimeters) unless otherwise noted
bs
Order Number: DP83815DVNG
O
NS Package Number: VNG144A
107
www.national.com
te
ol
e
Order Number: DP83815DUJB
bs
NS Package Number: UJB160A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
O
DP83815 10/100 Mb/s Integrated PCI Ethernet Media Access Controller and Physical Layer (MacPhyter™)
PHYSICAL DIMENSIONS inches (millimeters) unless otherwise noted (continued)
1. Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body, or (b) support
or sustain life, and whose failure to perform, when properly used
in accordance with instructions for use provided in the labeling,
can be reasonably expected to result in a significant injury to the
user.
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no “Banned
Substances” as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
www.national.com
Francais Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages