Dallas DS1225AB-85 64k nonvolatile sram Datasheet

DS1225AB/AD
64k Nonvolatile SRAM
www.dalsemi.com
FEATURES
PIN ASSIGNMENT
10 years minimum data retention in the
absence of external power
Data is automatically protected during power
loss
Directly replaces 8k x 8 volatile static RAM
or EEPROM
Unlimited write cycles
Low-power CMOS
JEDEC standard 28-pin DIP package
Read and write access times as fast as 70 ns
Lithium energy source is electrically
disconnected to retain freshness until power
is applied for the first time
Full ±10% VCC operating range (DS1225AD)
Optional ±5% VCC operating range
(DS1225AB)
Optional industrial temperature range of
-40°C to +85°C, designated IND
28
27
26
25
24
23
22
21
20
19
18
17
VCC
WE
NC
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ1
1
2
3
4
5
6
7
8
9
10
11
12
DQ2
13
16
DQ4
GND
14
15
DQ3
NC
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ5
28-Pin ENCAPSULATED PACKAGE
720-mil EXTENDED
PIN DESCRIPTION
A0-A12
DQ0-DQ7
CE
WE
OE
VCC
GND
NC
- Address Inputs
- Data In/Data Out
- Chip Enable
- Write Enable
- Output Enable
- Power (+5V)
- Ground
- No Connect
DESCRIPTION
The DS1225AB and DS1225AD are 65,536-bit, fully static, nonvolatile SRAMs organized as 8192 words
by 8 bits. Each NV SRAM has a self-contained lithium energy source and control circuitry which
constantly monitors VCC for an out-of-tolerance condition. When such a condition occurs, the lithium
energy source is automatically switched on and write protection is unconditionally enabled to prevent
data corruption. The NV SRAMs can be used in place of existing 8k x 8 SRAMs directly conforming to
the popular bytewide 28-pin DIP standard. The devices also match the pinout of the 2764 EPROM and
the 2864 EEPROM, allowing direct substitution while enhancing performance. There is no limit on the
number of write cycles that can be executed and no additional support circuitry is required for
microprocessor interfacing.
1 of 10
111899
DS1225AB/AD
READ MODE
The DS1225AB and DS1225AD execute a read cycle whenever WE (Write Enable) is inactive (high) and
CE (Chip Enable) and OE (Output Enable) are active (low). The unique address specified by the 13
address inputs (A0 -A12) defines which of the 8192 bytes of data is to be accessed. Valid data will be
available to the eight data output drivers within tACC (Access Time) after the last address input signal is
stable, providing that CE and OE access times are also satisfied. If CE and OE access times are not
satisfied, then data access must be measured from the later-occurring signal and the limiting parameter is
either tCO for CE or tOE for OE rather than address access.
WRITE MODE
The DS1225AB and DS1225AD execute a write cycle whenever the WE and CE signals are active
(low) after address inputs are stable. The later-occurring falling edge of CE or WE will determine the
start of the write cycle. The write cycle is terminated by the earlier rising edge of CE or WE . All address
inputs must be kept valid throughout the write cycle. WE must return to the high state for a minimum
recovery time (tWR ) before another cycle can be initiated. The OE control signal should be kept inactive
(high) during write cycles to avoid bus contention. However, if the output drivers are enabled ( CE and
OE active) then WE will disable the outputs in tODW from its falling edge.
DATA RETENTION MODE
The DS1225AB provides full functional capability for VCC greater than 4.75 volts and write protects by
4.5 volts. The DS1225AD provides full-functional capability for VCC greater than 4.5 volts and write
protects by 4.25 volts. Data is maintained in the absence of VCC without any additional support circuitry.
The nonvolatile static RAMs constantly monitor VCC. Should the supply voltage decay, the NV SRAMs
automatically write protect themselves, all inputs become “don’t care,” and all outputs become highimpedance. As VCC falls below approximately 3.0 volts, the power switching circuit connects the lithium
energy source to RAM to retain data. During power-up, when VCC rises above approximately 3.0 volts,
the power switching circuit connects external VCC to RAM and disconnects the lithium energy source.
Normal RAM operation can resume after VCC exceeds 4.75 volts for the DS1225AB and 4.5 volts for the
DS1225AD.
FRESHNESS SEAL
Each DS1225 is shipped from Dallas Semiconductor with the lithium energy source disconnected,
guaranteeing full energy capacity. When VCC is first applied at a level of greater than VTP , the lithium
energy source is enabled for battery backup operation.
2 of 10
DS1225AB/AD
ABSOLUTE MAXIMUM RATINGS*
Voltage on Any Pin Relative to Ground
Operating Temperature
Storage Temperature
Soldering Temperature
∗
-0.3V to +7.0V
0°C to 70°C; -40°C to +85°C for IND parts
-40°C to +70°C; -40°C to +85°C for IND parts
260°C for 10 seconds
This is a stress rating only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER
DS1225AB Power Supply Voltage
DS1225AD Power Supply Voltage
Logic 1
Logic 0
SYMBOL
VCC
VCC
VIH
VIL
MIN
4.75
4.50
2.2
0.0
TYP
5.0
5.0
MAX
5.25
5.5
VCC
+0.8
SYMBOL
IIL
MIN
-1.0
IIO
-1.0
IOH
IOL
ICCS1
ICCS2
-1.0
2.0
TYP
MAX
+1.0
UNITS
µA
+1.0
µA
10.0
5.0
mA
mA
mA
mA
ICC01
75
mA
ICC01
85
mA
5.0
3.0
VTP
4.50
4.62
4.75
V
VTP
4.25
4.37
4.5
V
SYMBOL
CIN
CI/O
MIN
TYP
5
5
MAX
10
10
UNITS
pF
pF
CAPACITANCE
PARAMETER
Input Capacitance
Input/Output Capacitance
UNITS
V
V
V
V
NOTES
(VCC =5V ± 5% for DS1225AB)
(TA: See Note 10)
(VCC =5V ± 10% for DS1225AD)
DC ELECTRICAL CHARACTERISTICS
PARAMETER
Input Leakage Current
I/O Leakage Current
CE > VIH< VCC
Output Current @ 2.4V
Output Current @ 0.4V
Standby Current CE =2.2V
Standby Current CE =VCC -0.5V
Operating Current tCYC=200 ns
(Commercial)
Operating Current tCYC=200 ns
(Industrial)
Write Protection Voltage
(DS1225AB)
Write Protection Voltage
(DS1225AD)
(TA: See Note 10)
NOTES
(TA =25°C)
3 of 10
NOTES
DS1225AB/AD
(VCC =5V ± 5% for DS1225AB)
(TA: See Note 10)
(VCC =5V ± 10% for DS1225AD)
AC ELECTRICAL CHARACTERISTICS
PARAMETER
Read Cycle Time
Access Time
OE to Output Valid
CE to Output Valid
OE or CE to Output Active
Output High Z from Deselection
Output Hold from Address
Change
Write Cycle Time
Write Pulse Width
Address Setup Time
Write Recovery Time
Output High Z from WE
Output Active from WE
Data Setup Time
Data Hold Time
SYMBOL
tRC
tACC
tOE
tCO
tCOE
tOD
tOH
tWC
tWP
tAW
tWR1
tWR2
tODW
tOEW
tDS
tDH1
tDH2
DS1225AB-70
DS1225AD-70
MIN MAX
70
70
35
70
5
25
5
70
55
0
0
10
DS1220AB-85
DS1220AD-85
MIN MAX
85
85
45
85
5
30
4 of 10
NOTES
ns
ns
ns
ns
ns
ns
5
5
5
ns
85
65
0
0
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
25
5
30
0
10
UNITS
30
5
35
0
10
3
12
13
5
5
4
12
13
DS1225AB/AD
AC ELECTRICAL CHARACTERISTICS (cont’d)
PARAMETER
Read Cycle Time
Access Time
OE to Output Valid
CE to Output Valid
OE or CE to Output Active
Output High Z from Deselection
Output Hold from Address
Change
Write Cycle Time
Write Pulse Width
Address Setup Time
Write Recovery Time
Output High Z from WE
Output Active from WE
Data Setup Time
Data Hold Time
SYMBOL
tRC
tACC
tOE
tCO
tCOE
tOD
tOH
tWC
tWP
tAW
tWR1
tWR2
tODW
tOEW
tDS
tDH1
tDH2
DS1225AB- 150
DS1225AD- 150
MIN
150
MAX
DS1220AB-200
DS1220AD-200
MIN
200
150
70
150
5
200
100
200
5
35
5
150
100
0
0
10
35
5 of 10
NOTES
ns
ns
ns
ns
ns
ns
5
5
5
ns
200
100
0
0
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
35
5
60
0
10
UNITS
MAX
35
5
80
0
10
3
12
13
5
5
4
12
13
DS1225AB/AD
READ CYCLE
SEE NOTE 1
WRITE CYCLE 1
SEE NOTES 2, 3, 4, 6, 7, 8 AND 12
WRITE CYCLE 2
SEE NOTES 2, 3, 4, 6, 7, 8 AND 13
6 of 10
DS1225AB/AD
POWER-DOWN/POWER-UP CONDITION
SEE NOTE 11
POWER-DOWN/POWER-UP TIMING
PARAMETER
CE at VIH before Power-Down
VCC slew from VTP to 0V
VCC slew from 0V to VTP
CE at VIH after Power-Up
(TA : See Note 10)
SYMBOL MIN TYP MAX
0
tPD
300
tF
300
tR
2
125
tREC
UNITS
µs
µs
µs
ms
NOTES
11
(TA = 25°C)
PARAMETER
Expected Data Retention Time
SYMBOL MIN TYP MAX
tDR
10
UNITS
years
NOTES
9
WARNING:
Under no circumstance are negative undershoots, of any amplitude, allowed when device is in battery
backup mode.
7 of 10
DS1225AB/AD
NOTES:
1. WE is high for a read cycle.
2. OE = VIH or VIL. If OE = VIH during write cycle, the output buffers remain in a high-impedance
state.
3. tWP is specified as the logical AND of CE and WE . tWP is measured from the latter of CE or WE
going low to the earlier of CE or WE going high.
4. tDS are measured from the earlier of CE or WE going high.
5. These parameters are sampled with a 5 pF load and are not 100% tested.
6. If the CE low transition occurs simultaneously with or later than the WE low transition, the output
buffers remain in a high-impedance state during this period.
7. If the CE high transition occurs prior to or simultaneously with the WE high transition, the output
buffers remain in a high-impedance state during this period.
8. If WE is low or the WE low transition occurs prior to or simultaneously with the CE low transition,
the output buffers remain in a high-impedance state during this period.
9. Each DS1225AB and each DS1225AD has a built-in switch that disconnects the lithium source until
VCC is first applied by the user. The expected tDR is defined as accumulative time in the absence of
VCC starting from the time power is first applied by the user.
10. All AC and DC electrical characteristics are valid over the full operating temperature range. For
commercial products, this range is 0°C to 70°C. For industrial products (IND), this range is -40°C to
+85°C.
11. In a power down condition the voltage on any pin may not exceed the voltage on VCC .
12. tWR1 , tDH1 are measured from WE going high.
13. tWR2 , tDH2 are measured from CE going high.
14. DS1225AB and DS1225AD modules are recognized by Underwriters Laboratory (U.L.) under file
E99151.
DC TEST CONDITIONS
AC TEST CONDITIONS
Outputs Open
All Voltages Are Referenced to Ground
Output Load: 100 pF + 1TTL Gate
Input Pulse Levels: 0 - 3.0V
Timing Measurement Reference Levels
Input: 1.5V
Output: 1.5V
Input Pulse Rise and Fall Times: 5ns
8 of 10
DS1225AB/AD
ORDERING INFORMATION
9 of 10
DS1225AB/AD
DS1225AB/AD NONVOLATILE SRAM, 28-PIN, 720-MIL EXTENDED MODULE
PKG
DIM
A IN.
MM
B IN.
MM
C IN.
MM
D IN.
MM
E IN.
MM
F IN.
MM
G IN.
MM
H IN
MM
J IN.
MM
K IN.
MM
10 of 10
28-PIN
MIN
MAX
1.520
1.540
38.61
39.12
0.695
0.720
17.65
18.29
0.395
0.415
10.03
10.54
0.100
0.130
2.54
3.30
0.017
0.030
0.43
0.76
0.120
0.160
3.05
4.06
0.090
0.110
2.29
2.79
0.590
0.630
14.99
16.00
0.008
0.012
0.20
0.30
0.015
0.021
0.38
0.53
Similar pages