TI DS90CR211MTDX

DS90CR211,DS90CR212
DS90CR211/DS90CR212 21-Bit Channel Link
Literature Number: SNLS112A
DS90CR211/DS90CR212
21-Bit Channel Link
General Description
The DS90CR211 transmitter converts 21 bits of CMOS/TTL
data into three LVDS (Low Voltage Differential Signaling)
data streams. A phase-locked transmit clock is transmitted in
parallel with the data streams over a fourth LVDS link. Every
cycle of the transmit clock 21 bits of input data are sampled
and transmitted. The DS90CR212 receiver converts the
LVDS data streams back into 21 bits of CMOS/TTL data. At
a transmit clock frequency of 40 MHz, 21 bits of TTL data are
transmitted at a rate of 280 Mbps per LVDS data channel.
Using a 40 MHz clock, the data throughput is 840
Mbit/s(105 Mbyte/s).
The multiplexing of the data lines provides a substantial
cable reduction. Long distance parallel single-ended buses
typically require a ground wire per active signal (and have
very limited noise rejection capability). Thus, for a 21-bit wide
data bus and one clock, up to 44 conductors are required.
With the Channel Link chipset as few as 9 conductors (3
data pairs, 1 clock pair and a minimum of one ground) are
needed. This provides a 80% reduction in required cable
width, providing a system cost savings, reduces connector
physical size, and reduces shielding requirements due to the
cables smaller form factor.
The 21 CMOS/TTL inputs can support a variety of signal
combinations. For example, 5 4-bit nibbles plus 1 control, or
2 9-bit (byte + parity) and 3 control.
Features
n
n
n
n
n
n
n
n
Narrow bus reduces cable size and cost
± 1V Common mode range (ground shifting)
290 mV swing LVDS data transmission
840 Mbit/s data throughput
Low swing differential current mode drivers reduce EMI
Rising edge data strobe
Power down mode
Offered in low profile 48-lead TSSOP package
Block Diagrams
DS90CR211
DS90CR212
DS012637-27
Order Number DS90CR211MTD
See NS Package Number MTD48
DS012637-1
Order Number DS90CR212MTD
See NS Package Number MTD48
TRI-STATE ® is a registered trademark of National Semiconductor Corporation.
© 2000 National Semiconductor Corporation
DS012637
www.national.com
DS90CR211/DS90CR212 21-Bit Channel Link
July 1997
DS90CR211/DS90CR212
Connection Diagrams
DS90CR211
DS90CR212
DS012637-2
DS012637-3
Typical Application
DS012637-19
www.national.com
2
MTD48 (TSSOP) Package:
DS90CR211
1.98W
DS90CR212
1.89W
Package Derating:
DS90CR211
16 mW/˚C above +25˚C
DS90CR212
15 mW/˚C above +25˚C
This device does not meet 2000V ESD rating (Note 4) .
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (VCC)
−0.3V to +6V
CMOS/TTL Input Voltage
−0.3V to (VCC + 0.3V)
CMOS/TTL Ouput Voltage
−0.3V to (VCC + 0.3V)
LVDS Receiver Input Voltage
−0.3V to (VCC + 0.3V)
LVDS Driver Output Voltage
−0.3V to (VCC + 0.3V)
LVDS Output
Short Circuit Duration
continuous
Junction Temperature
+150˚C
Storage Temperature Range
−65˚C to +150˚C
Lead Temperature
(Soldering, 4 sec.)
+260˚C
Maximum Power Dissipation @ +25˚C
Recommended Operating
Conditions
Supply Voltage (VCC)
Operating Free Air Temperature (TA)
Receiver Input Range
Supply Noise Voltage (VCC)
Min
4.5
−10
0
Max
5.5
+70
2.4
100
Units
V
˚C
V
mVPP
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Conditions
Min
Typ
Max
Units
VCC
V
0.8
V
0.1
0.3
V
CMOS/TTL DC SPECIFICATIONS
VIH
High Level Input Voltage
2.0
VIL
Low Level Input Voltage
VOH
High Level Output Voltage
IOH = −0.4 mA
VOL
Low Level Output Voltage
IOL = 2 mA
VCL
Input Clamp Voltage
ICL = −18 mA
−0.79
−1.5
V
IIN
Input Current
VIN = VCC, GND, 2.5V or 0.4V
± 5.1
± 10
µA
IOS
Output Short Circuit Current
VOUT = 0V
−120
mA
GND
3.8
4.9
V
LVDS DRIVER DC SPEClFlCATIONS
VOD
Differential Output Voltage
∆VOD
Change in VOD between
RL = 100Ω
250
290
450
mV
35
mV
Complementary Output States
VCM
Common Mode Voltage
∆VCM
Change in VCM between
IOS
Output Short Circuit Current
IOZ
TRI-STATE ®
1.1
1.25
1.375
V
35
mV
−2.9
−5
mA
±1
± 10
µA
+100
mV
Complementary Output States
Output
Current
VOUT = 0V, RL = 100Ω
Power Down = 0V, VOUT = 0V or VCC
LVDS RECEIVER DC SPECIFlCATIONS
VTH
Differential Input High Threshold
VTL
Differential Input Low Threshold
IIN
Input Current
VCM = +1.2V
−100
VIN = +2.4V
mV
< ±1
< ±1
± 10
± 10
µA
f = 32.5 MHz
34
51
mA
f = 37.5 MHz
36
53
mA
1
25
µA
f = 32.5 MHz
55
75
mA
f = 37.5 MHz
60
80
mA
VCC = 5.5V
VIN = 0V
µA
TRANSMITTER SUPPLY CURRENT
ICCTW
Transmitter Supply Current,
Worst Case
RL = 100Ω, CL = 5 pF,
Worst Case Pattern
(Figure 1, Figure 2)
ICCTZ
Transmitter Supply Current,
Power Down
Power Down = Low
RECEIVER SUPPLY CURRENT
ICCRW
Receiver Supply Current,
Worst Case
CL = 8 pF,
Worst Case Pattern
(Figure 1, Figure 3)
3
www.national.com
DS90CR211/DS90CR212
Absolute Maximum Ratings (Note 1)
DS90CR211/DS90CR212
Electrical Characteristics
(Continued)
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Conditions
Min
Typ
Max
Units
1
10
µA
RECEIVER SUPPLY CURRENT
ICCRZ
Receiver Supply Current,
Power Down
Power Down = Low
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.
Note 2: Typical values are given for VCC = 5.0V and TA = +25˚C.
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise specified (except VOD and ∆VOD).
Note 4: ESD Rating:
HBM (1.5 kΩ, 100 pF)
PLL V CC ≥ 1000V
All other pins ≥ 2000V
EIAJ (0Ω, 200 pF) ≥ 150V
Transmitter Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Min
Typ
Max
Units
ns
LLHT
LVDS Low-to-High Transition Time (Figure 2)
0.75
1.5
LHLT
LVDS High-to-Low Transition Time (Figure 2)
0.75
1.5
ns
TCIT
TxCLK IN Transition Time (Figure 4)
8
ns
TCCS
TxOUT Channel-to-Channel Skew (Note 5) (Figure 5)
350
ps
TPPos0
Transmitter Output Pulse Position for Bit0 (Figure 16)
−200
150
350
ps
TPPos1
Transmitter Output Pulse Position for Bit1
6.3
7.2
7.5
ns
TPPos2
Transmitter Output Pulse Position for Bit2
12.8
13.6
14.6
ns
TPPos3
Transmitter Output Pulse Position for Bit3
20
20.8
21.5
ns
TPPos4
Transmitter Output Pulse Position for Bit4
27.2
28
28.5
ns
TPPos5
Transmitter Output Pulse Position for Bit5
34.5
35.2
35.6
ns
TPPos6
Transmitter Output Pulse Position for Bit6
42.2
42.6
42.9
ns
TPPos0
Transmitter Output Pulse Position for Bit0 (Figure 16)
−100
100
300
ps
TPPos1
Transmitter Output Pulse Position for Bit1
2.9
3.3
3.9
ns
TPPos2
Transmitter Output Pulse Position for Bit2
6.1
6.6
7.1
ns
TPPos3
Transmitter Output Pulse Position for Bit3
9.7
10.2
10.7
ns
TPPos4
Transmitter Output Pulse Position for Bit4
13
13.5
14.1
ns
TPPos5
Transmitter Output Pulse Position for Bit5
17
17.4
17.8
ns
TPPos6
Transmitter Output Pulse Position for Bit6
20.3
20.8
21.4
ns
f = 20 MHz
f = 40 MHz
TCIP
TxCLK IN Period (Figure 6)
25
T
50
ns
TCIH
TxCLK IN High Time (Figure 6)
0.35T
0.5T
0.65T
ns
TCIL
TxCLK IN Low Time (Figure 6)
0.35T
0.5T
0.65T
ns
TSTC
TxIN Setup to TxCLK IN (Figure 6)
f = 20 MHz
14
f = 40 MHz
8
ns
ns
THTC
TxIN Hold to TxCLK IN (Figure 6)
TCCD
TxCLK IN to TxCLK OUT Delay @ 25˚C, VCC = 5.0V (Figure 8)
9.7
ns
TPLLS
Transmitter Phase Lock Loop Set (Figure 10)
10
ms
TPDD
Transmitter Powerdown Delay (Figure 14)
100
ns
2.5
Note 5: This limit based on bench characterization.
www.national.com
4
5
2
ns
Over recommended operating supply and temperature ranges unless otherwise specified
Typ
Max
Units
CLHT
Symbol
CMOS/TTL Low-to-High Transition Time (Figure 3)
Parameter
Min
3.5
6.5
ns
CHLT
CMOS/TTL High-to-Low Transition Time (Figure 3)
2.7
6.5
ns
T
50
ns
RCOP
RxCLK OUT Period (Figure 7)
RSKM
Receiver Skew Margin (Note 6)
f = 20 MHz
1.1
ns
VCC = 5V, TA = 25˚C (Figure 17)
f = 40 MHz
700
ps
RCOH
RxCLK OUT High Time (Figure 7)
f = 20 MHz
19
ns
f = 40 MHz
6
ns
RCOL
RxCLK OUT Low Time (Figure 7)
f = 20 MHz
21.5
ns
f = 40 MHz
10.5
ns
f = 20 MHz
14
ns
f = 40 MHz
4.5
ns
f = 20 MHz
16
ns
f = 40 MHz
6.5
ns
RSRC
RHRC
25
RxCLK Setup to RxCLK OUT (Figure 7)
RxCLK Hold to RxCLK OUT (Figure 7)
RCCD
RxCLK IN to RxCLK OUT Delay @ 25˚C, VCC = 5.0V (Figure 9)
11.9
ns
RPLLS
Receiver Phase Lock Loop Set (Figure 11)
10
ms
RPDD
Receiver Powerdown Delay (Figure 15)
1
µs
7.6
Note 6: Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account for transmitter output skew(TCCS)
and the setup and hold time (internal data sampling window), allowing LVDS cable skew dependent on type/length and source clock(TxCLK IN) jitter.
RSKM ≥ cable skew (type, length) + source clock jitter (cycle to cycle).
AC Timing Diagrams
DS012637-4
FIGURE 1. “WORST CASE” Test Pattern
DS012637-5
DS012637-6
FIGURE 2. DS90CR211 (Transmitter) LVDS Output Load and Transition Timing
DS012637-7
DS012637-8
FIGURE 3. DS90CR212 (Receiver) CMOS/TTL Output Load and Transition Timing
5
www.national.com
DS90CR211/DS90CR212
Receiver Switching Characteristics
DS90CR211/DS90CR212
AC Timing Diagrams
(Continued)
DS012637-9
FIGURE 4. DS90CR211 (Transmitter) Input Clock Transition Time
DS012637-10
Measurements at Vdiff = 0V
TCCS measured between earliest and latest initial LVDS edges.
TxCLK OUT Differential Low → High Edge
FIGURE 5. DS90CR211 (Transmitter) Channel-to-Channel Skew and Pulse Width
DS012637-11
FIGURE 6. DS90CR211 Setup/Hold and High/Low Times
DS012637-12
FIGURE 7. DS90CR212 Setup/Hold and High/Low Times
www.national.com
6
DS90CR211/DS90CR212
AC Timing Diagrams
(Continued)
DS012637-13
FIGURE 8. DS90CR211 (Transmitter) Clock In to Clock Out Delay
DS012637-14
FIGURE 9. DS90CR212 (Receiver) Clock In to Clock Out Delay
DS012637-15
FIGURE 10. DS90CR211 (Transmitter) Phase Lock Loop Set Time
DS012637-16
FIGURE 11. DS90CR212 (Receiver) Phase Lock Loop Set Time
7
www.national.com
DS90CR211/DS90CR212
AC Timing Diagrams
(Continued)
DS012637-17
FIGURE 12. Seven Bits of LVDS in One Clock Cycle
DS012637-18
FIGURE 13. 21 Parallel TTL Data Inputs Mapped to LVDS Outputs (DS90CR211)
DS012637-23
FIGURE 14. Transmitter Powerdown Delay
DS012637-24
FIGURE 15. Receiver Powerdown Delay
www.national.com
8
DS90CR211/DS90CR212
AC Timing Diagrams
(Continued)
DS012637-25
FIGURE 16. Transmitter LVDS Output Pulse Position Measurement
DS012637-26
SW — Setup and Hold Time (Internal data sampling window)
TCCS — Transmitter Output Skew
RSKM ≥ Cable Skew (type, length) + Source Clock Jitter (cycle to cycle)
Cable Skew — Typically 10 ps–40 ps per foot
FIGURE 17. Receiver LVDS Input Skew Margin
DS90CR211 Pin Description—Channel Link Transmitter (Tx)
Pin Name
I/O
No.
Description
TxIN
I
21
TTL Level inputs
TxOUT+
O
3
Positive LVDS differential data output
TxOUT−
O
3
Negative LVDS differential data output
TxCLK IN
I
1
TTL level clock input. The rising edge acts as data strobe
TxCLK OUT+
O
1
Positive LVDS differential clock output
TxCLK OUT−
O
1
Negative LVDS differential clock output
PWR DOWN
I
1
TTL level input. Assertion (low input) TRI-STATES the outputs, ensuring low current at power down
VCC
I
4
Power supply pins for TTL inputs
GND
I
5
Ground pins for TTL inputs
9
www.national.com
DS90CR211/DS90CR212
DS90CR211 Pin Description—Channel Link Transmitter (Tx)
Pin Name
PLL VCC
I/O
No.
I
1
(Continued)
Description
Power supply pin for PLL
PLL GND
I
2
Ground pins for PLL
LVDS VCC
I
1
Power supply pin for LVDS outputs
LVDS GND
I
3
Ground pins for LVDS outputs
DS90CR212 Pin Description—Channel Link Receiver (Rx)
Pin Name
RxIN+
I/O
No.
I
3
Positive LVDS differential data inputs
Description
Negative LVDS differential data inputs
RxIN−
I
3
RxOUT
O
21
TTL level outputs
RxCLK IN+
I
1
Positive LVDS differential clock input
RxCLK IN−
I
1
Negative LVDS differential clock input
RxCLK OUT
O
1
TTL level clock output. The rising edge acts as data strobe
PWR DOWN
I
1
TTL level input. Assertion (low input) maintains the receiver outputs in the previous state
VCC
I
4
Power supply pins for TTL outputs
GND
I
5
Ground pins for TTL outputs
PLL VCC
I
1
Power supply for PLL
PLL GND
I
2
Ground pin for PLL
LVDS VCC
I
1
Power supply pin for LVDS inputs
LVDS GND
I
3
Ground pins for LVDS inputs
In addition to the four or five cable pairs that carry data and
clock, it is recommended to provide at least one additional
conductor (or pair) which connects ground between the
transmitter and receiver. This low impedance ground provides a common mode return path for the two devices. Some
of the more commonly used cable types for point-to-point applications include flat ribbon, flex, twisted pair and
Twin-Coax. All are available in a variety of configurations and
options. Flat ribbon cable, flex and twisted pair generally perform well in short point-to-point applications while Twin-Coax
is good for short and long applications. When using ribbon
cable, it is recommended to place a ground line between
each differential pair to act as a barrier to noise coupling between adjacent pairs. For Twin-Coax cable applications, it is
recommended to utilize a shield on each cable pair. All extended point-to-point applications should also employ an
overall shield surrounding all cable pairs regardless of the
cable type. This overall shield results in improved transmission parameters such as faster attainable speeds, longer
distances between transmitter and receiver and reduced
problems associated with EMS or EMI.
The high-speed transport of LVDS signals has been demonstrated on several types of cables with excellent results.
However, the best overall performance has been seen when
using Twin-Coax cable. Twin-Coax has very low cable skew
and EMI due to its construction and double shielding. All of
the design considerations discussed here and listed in the
supplemental application notes provide the subsystem communications designer with many useful guidelines. It is recommended that the designer assess the tradeoffs of each
application thoroughly to arrive at a reliable and economical
cable solution.
BOARD LAYOUT: To obtain the maximum benefit from the
noise and EMI reductions of LVDS, attention should be paid
Applications Information
The Channel Link devices are intended to be used in a wide
variety of data transmission applications. Depending upon
the application the interconnecting media may vary. For example, for lower data rate (clock rate) and shorter cable
lengths ( < 2m), the media electrical performance is less critical. For higher speed/long distance applications the media’s
performance becomes more critical. Certain cable constructions provide tighter skew (matched electrical length between the conductors and pairs). Twin-coax for example, has
been demonstrated at distances as great as 10 meters and
with the maximum data transfer of 1.12 Gbit/s. Additional applications information can be found in the following National
Interface Application Notes:
AN = ####
Topic
AN-1035
PCB Design Guidelines for LVDS and
Link Devices
AN-806
Transmission Line Theory
AN-905
Transmission Line Calculations and
Differential Impedance
AN-916
Cable Information
CABLES: A cable interface between the transmitter and receiver needs to support the differential LVDS pairs. The
21-bit CHANNEL LINK chipset (DS90CR211/212) requires
four pairs of signal wires and the 28-bit CHANNEL LINK
chipset (DS90CR281/282) requires five pairs of signal wires.
The ideal cable/connector interface would have a constant
100Ω differential impedance throughout the path. It is also
recommended that cable skew remain below 350 ps ( @ 40
MHz clock rate) to maintain a sufficient data sampling window at the receiver.
www.national.com
10
the other line of the differential pair. Care should be taken to
ensure that the differential trace impedance match the differential impedance of the selected physical media (this impedance should also match the value of the termination resistor
that is connected across the differential pair at the receiver’s
input). Finally, the location of the CHANNEL LINK TxOUT/
RxIN pins should be as close as possible to the board edge
so as to eliminate excessive pcb runs. All of these considerations will limit reflections and crosstalk which adversely effect high frequency performance and EMI.
(Continued)
to the layout of differential lines. Lines of a differential pair
should always be adjacent to eliminate noise interference
from other signals and take full advantage of the noise canceling of the differential signals. The board designer should
also try to maintain equal length on signal traces for a given
differential pair. As with any high speed design, the impedance discontinuities should be limited (reduce the numbers
of vias and no 90 degree angles on traces). Any discontinuities which do occur on one signal line should be mirrored in
DS012637-20
FIGURE 18. LVDS Serialized Link Termination
UNUSED INPUTS: All unused inputs at the TxW inputs of
the transmitter must be tied to ground. All unused outputs at
the RxOUT outputs of the receiver must then be left floating.
TERMINATION: Use of current mode drivers requires a terminating resistor across the receiver inputs. The CHANNEL
LINK chipset will normally require a single 100Ω resistor between the true and complement lines on each differential
pair of the receiver input. The actual value of the termination
resistor should be selected to match the differential mode
characteristic impedance (90Ω to 120Ω typical) of the cable.
Figure 18 shows an example. No additional pull-up or
pull-down resistors are necessary as with some other differential technologies such as PECL. Surface mount resistors
are recommended to avoid the additional inductance that accompanies leaded resistors. These resistors should be
placed as close as possible to the receiver input pins to reduce stubs and effectively terminate the differential lines.
DECOUPLING CAPACITORS: Bypassing capacitors are
needed to reduce the impact of switching noise which could
limit performance. For a conservative approach three
parallel-connected decoupling capacitors (Multi-Layered Ceramic type in surface mount form factor) between each VCC
and the ground plane(s) are recommended. The three capacitor values are 0.1 µF, 0.01µF and 0.001 µF. An example
is shown in Figure 19. The designer should employ wide
traces for power and ground and ensure each capacitor has
its own via to the ground plane. If board space is limiting the
number of bypass capacitors, the PLL VCC should receive
the most filtering/bypassing. Next would be the LVDS VCC
pins and finally the logic VCC pins.
DS012637-21
FIGURE 19. CHANNEL LINK
Decoupling Configuration
CLOCK JITTER: The CHANNEL LINK devices employ a
PLL to generate and recover the clock transmitted across the
LVDS interface. The width of each bit in the serialized LVDS
data stream is one-seventh the clock period. For example, a
40 MHz clock has a period of 25 ns which results in a data bit
width of 3.57 ns. Differential skew (∆t within one differential
pair), interconnect skew (∆t of one differential pair to another) and clock jitter will all reduce the available window for
sampling the LVDS serial data streams. Care must be taken
to ensure that the clock input to the transmitter be a clean
low noise signal. Individual bypassing of each VCC to ground
will minimize the noise passed on to the PLL, thus creating a
low jitter LVDS clock. These measures provide more margin
for channel-to-channel skew and interconnect skew as a part
of the overall jitter/skew budget.
11
www.national.com
DS90CR211/DS90CR212
Applications Information
DS90CR211/DS90CR212
Applications Information
(Continued)
DS012637-22
FIGURE 20. Single-Ended and Differential Waveforms
COMMON MODE vs. DIFFERENTIAL MODE NOISE MARGIN: The typical signal swing for LVDS is 300 mV centered
at +1.2V. The CHANNEL LINK receiver supports a 100 mV
threshold therefore providing approximately 200 mV of differential noise margin. Common mode protection is of more importance to the system’s operation due to the differential
data transmission. LVDS supports an input voltage range of
Ground to +2.4V. This allows for a ± 1.0V shifting of the center point due to ground potential differences and common
mode noise.
POWER SEQUENCING AND POWERDOWN MODE: Outputs of the CHANNEL LINK transmitter remain in
TRI-STATE ® until the power supply reaches 3V. Clock and
data outputs will begin to toggle 10 ms after VCChas reached
www.national.com
4.5V and the Powerdown pin is above 2V. Either device may
be placed into a powerdown mode at any time by asserting
the Powerdown pin (active low). Total power dissipation for
each device will decrease to 5 µW (typical).
The CHANNEL LINK chipset is designed to protect itself
from accidental loss of power to either the transmitter or receiver. If power to the transmit board is lost, the receiver
clocks (input and output) stop. The data outputs (RxOUT) retain the states they were in when the clocks stopped. When
the receiver board loses power, the receiver inputs are
shorted to V CC through an internal diode. Current is limited
(5 mA per input) by the fixed current mode drivers, thus
avoiding the potential for latchup when powering the device.
12
DS90CR211/DS90CR212 21-Bit Channel Link
Physical Dimensions
inches (millimeters) unless otherwise noted
48-Lead Molded Thin Shrink Small Outline Package, JEDEC
Order Number DS90CR211MTD or DS90CR212MTD
NS Package Number MTD48
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated