NSC DS92LV2411SQX 5-50mhz 24-bit channel link ii serializer and deserializer Datasheet

DS92LV2411/DS92LV2412
May 25, 2010
5-50MHz 24-Bit Channel Link II Serializer and Deserializer
General Description
Features
The DS92LV2411 (Serializer) / DS92LV2412 (Deserializer)
chipset translates a parallel 24–bit LVCMOS data interface
into a single high-speed CML serial interface with embedded
clock information. This single serial stream eliminates skew
issues between clock and data, reduces connector size and
interconnect cost for transferring a 24-bit, or less, bus over
FR-4 printed circuit board backplanes, differential or coax cables.
In addition to the 24-bit data bus interface, the
DS92LV2411/12 also features a 3-bit control bus for slow
speed signals. This allows implementing video and display
applications with up to 24–bits per pixel (RGB888), or embedding audio information with compressed video formats.
Programmable transmit de-emphasis, receive equalization,
on-chip scrambling and DC balancing enables long distance
transmission over lossy cables and backplanes. The
DS92LV2412 automatically locks to incoming data without an
external reference clock or special sync patterns, providing
easy “plug-and-go” or “hot plug” operation. EMI is minimized
by the use of low voltage differential signaling, receiver drive
strength control, and spread spectrum clocking capability.
The DS92LV2411/12 chipset is programmable though an I2C
interface as well as through pins. A built-in AT-SPEED BIST
feature validates link integrity and may be used for system
diagnostics.
The DS92LV2411 is offered in a 48-pin LLP and the
DS92LV2412 is offered in a 60-pin LLP package. Both devices operate over the full industrial temperature range of -40°
C to +85°C.
■
■
■
■
■
■
■
■
■
24–bit data, 3–bit control, 5 – 50 MHz clock
Application payloads up to 1.2 Gbps
AC coupled interconnects: STP up to 10 m or coax 20+ m
1.8V or 3.3V compatible LVCMOS I/O interface
Integrated terminations on Ser and Des
AT-SPEED BIST mode and reporting pin
Configurable by pins or I2C compatible serial control bus
Power down mode minimizes power dissipation
>8 kV HBM ESD Rating
SERIALIZER — DS92LV2411
■ Supports Spread Spectrum Clocking (SSC) on inputs
■ Data scrambler for reduced EMI
■ DC-balance encoder for AC coupling
■ Selectable output VOD and adjustable de-emphasis
DESERIALIZER — DS92LV2412
■ Random data lock; no reference clock required
■ Adjustable input receiver equalization
■ LOCK (real time link status) reporting pin
■ Selectable Spread Spectrum Clock Generation (SSCG)
and output slew rate control (OS) to reduce EMI
Applications
■
■
■
■
■
■
Embedded Video and Display
Medical Imaging
Factory Automation
Office Automation — Printer, Scanner
Security and Video Surveillance
General purpose data communication
Applications Diagram
30065327
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2010 National Semiconductor Corporation
300653
www.national.com
DS92LV2411/DS92LV2412 5-50MHz 24-Bit Channel Link II Serializer and Deserializer
PRELIMINARY
DS92LV2411/DS92LV2412
Block Diagrams
30065328
30065329
Ordering Information
NSID
Package Description
Quantity
SPEC
Package ID
DS92LV2411SQ
48–pin LLP, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch
TBD
NOPB
SQA48A
DS92LV2411SQX
48–pin LLP, 7.0 X 7.0 X 0.8 mm, 0.5 mm pitch
1000
NOPB
SQA48A
DS92LV2412SQ
60–pin LLP, 9.0 X 9.0 X 0.8 mm, 0.5 mm pitch
TBD
NOPB
SQA60B
DS92LV2412SQX
60–pin LLP, 9.0 X 9.0 X 0.8 mm, 0.5 mm pitch
1000
NOPB
SQA60B
www.national.com
2
DS92LV2411/DS92LV2412
DS92LV2411 Pin Diagram
30065319
Serializer - DS92LV2411 — Top View
3
www.national.com
DS92LV2411/DS92LV2412
DS92LV2411 Serializer Pin Descriptions
Pin Name
Pin #
I/O, Type
Description
LVCMOS Parallel Interface
DI[7:0]
34, 33, 32, 29, I, LVCMOS Parallel Interface Data Input Pins
28, 27, 26, 25 w/ pull-down For 8–bit RED Display: DI7 = R7 – MSB, DI0 = R0 – LSB.
DI[15:8]
42, 41, 40, 39, I, LVCMOS Parallel Interface Data Input Pins
38, 37, 36, 35 w/ pull-down For 8–bit GREEN Display: DI15 = G7 – MSB, DI8 = G0 – LSB.
DI[23:16]
2, 1, 48, 47,
I, LVCMOS Parallel Interface Data Input Pins
46, 45, 44, 43 w/ pull-down For 8–bit BLUE Display: DI23 = B7 – MSB, DI16 = B0 – LSB.
CI1
5
I, LVCMOS Control Signal Input
w/ pull-down For Display/Video Application:
CI1 = Data Enable Input
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum
transition pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
CI2
3
I, LVCMOS Control Signal Input
w/ pull-down For Display/Video Application:
CI2 = Horizontal Sync Input
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum
transition pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
CI3
4
I, LVCMOS Control Signal Input
w/ pull-down For Display/Video Application:
CI3 = Vertical Sync Input
CI3 is limited to 1 transition per 130 clock cycles. Thus, the minimum pulse width allowed
is 130 clock cycle wide.
CLKIN
10
I, LVCMOS Clock Input
w/ pull-down Latch/data strobe edge set by RFB pin.
Control and Configuration
PDB
21
I, LVCMOS Power-down Mode Input
w/ pull-down PDB = 1, Ser is enabled (normal operation).
Refer to ”Power Up Requirements and PDB Pin” in the Applications Information Section.
PDB = 0, Ser is powered down
When the Ser is in the power-down state, the driver outputs (DOUT+/-) are both logic high,
the PLL is shutdown, IDD is minimized. Control Registers are RESET.
VODSEL
24
I, LVCMOS Differential Driver Output Voltage Select
w/ pull-down VODSEL = 1, CML VOD is ±420 mV, 840 mVp-p (typ) — long cable / De-Emph applications
VODSEL = 0, CML VOD is ±280 mV, 560 mVp-p (typ) — short cable (no De-emph), low
power mode.
This is can also be control by I2C register.
De-Emph
23
RFB
11
www.national.com
I, Analog
w/ pull-up
De-Emphasis Control
De-Emph = open (float) - disabled
To enable De-emphasis, tie a resistor from this pin to GND or control via register.
See Table 3.
This can also be controlled by I2C register access.
I, LVCMOS Clock Input Latch/Data Strobe Edge Select
w/ pull-down RFB = 1, parallel interface data and control signals are latched on the rising clock edge.
RFB = 0, parallel interface data and control signals are latched on the falling clock edge.
This can also be controlled by I2C register access.
4
Pin #
CONFIG
[1:0]
13, 12
I/O, Type
Description
I, LVCMOS 00: Control Signal Filter DISABLED
w/ pull-down 01: Control Signal Filter ENABLED
10: Reverse compatibility mode to interface with the DS90UR124 or DS99R124Q
11: Reverse compatibility mode to interface with the DS90C124
ID[x]
6
I, Analog
I2C Serial Control Bus Device ID Address Select — Optional
Resistor to Ground and 10 kΩ pull-up to 1.8V rail. See Table 10.
SCL
8
I, LVCMOS
SDA
9
I/O, LVCMOS I2C Serial Control Bus Data Input / Output - Optional
Open Drain SDA requires an external pull-up resistor VDDIO.
BISTEN
31
I, LVCMOS BIST Mode — Optional
w/ pull-down BISTEN = 0, BIST is disabled (normal operation)
BISTEN = 1, BIST is enabled
RES[2:0]
18, 16, 15
I2C Serial Control Bus Clock Input - Optional
SCL requires an external pull-up resistor to VDDIO.
I, LVCMOS Reserved - tie LOW
w/ pull-down
Channel-Link II — CML Serial Interface
DOUT+
20
O, CML
Non–Inverting Output.
The output must be AC Coupled with a 0.1 µF capacitor.
DOUT-
19
O, CML
Inverting Output.
The output must be AC Coupled with a 0.1 µF capacitor.
Power and Ground
VDDL
7
Power
Logic Power, 1.8 V ±5%
VDDP
14
Power
PLL Power, 1.8 V ±5%
VDDHS
17
Power
TX High Speed Logic Power, 1.8 V ±5%
VDDTX
22
Power
Output Driver Power, 1.8 V ±5%
VDDIO
30
Power
LVCMOS I/O Power, 1.8 V ±5% OR 3.3 V ±10%
DAP
Ground
DAP is the large metal contact at the bottom side, located at the center of the LLP
package. Connect to the ground plane (GND) with at least 9 vias.
GND
NOTE: 1= HIGH, 0 L= LOW
The VDD (VDDn and VDDIO) supply ramp should be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms then a capacitor
on the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage.
5
www.national.com
DS92LV2411/DS92LV2412
Pin Name
DS92LV2411/DS92LV2412
DS92LV2412 Pin Diagram
30065320
Deserializer - DS92LV2412 — Top View
www.national.com
6
Pin Name
Pin #
I/O, Type
Description
LVCMOS Parallel Interface
DO[7:0]
33, 34, 35,
36, 37, 39,
40, 41
I, STRAP, Parallel Interface Data Output Pins
O, LVCMOS For 8–bit RED Display: DO7 = R7 – MSB, DO0 = R0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
DO[15:8]
20, 21, 22,
23, 25, 26,
27, 28
I, STRAP, Parallel Interface Data Output Pins
O, LVCMOS For 8–bit GREEN Display: DO15 = G7 – MSB, DO8 = G0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
DO[23:16]
9, 10, 11,
12, 14, 17,
18, 19
I, STRAP, Parallel Interface Data Input Pins
O, LVCMOS For 8–bit BLUE Display: DO23 = B7 – MSB, DO16 = B0 – LSB.
In power-down (PDB = 0), outputs are controlled by the OSS_SEL (See Table 7). These
pins are inputs during power-up (See STRAP Inputs).
CO1
6
O, LVCMOS Control Signal Output
For Display/Video Application:
CO1 = Data Enable Output
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CO2
8
O, LVCMOS Control Signal Output
For Display/Video Application:
CO2 = Horizontal Sync Output
Control signal pulse width must be 3 clocks or longer to be transmitted when the Control
Signal Filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition
pulse when the Control Signal Filter is disabled (CONFIG[1:0] = 00).
The signal is limited to 2 transitions per 130 clocks regardless of the Control Signal Filter
setting.
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CO3
7
O, LVCMOS Control Signal Output
For Display/Video Application:
CO3 = Vertical Sync Output
CO3 is different than CO1 and CO2 because it is limited to 1 transition per 130 clock cycles.
Thus, the minimum pulse width allowed is 130 clock cycle wide.
The CONFIG[1:0] pins have no affect on CO3 signal
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7).
CLKOUT
5
O, LVCMOS Pixel Clock Output
In power-down (PDB = 0), output is controlled by the OSS_SEL pin (See Table 7). Data
strobe edge set by RFB.
LOCK
32
O, LVCMOS LOCK Status Output
LOCK = 1, PLL is Locked, outputs are active LOCK = 0, PLL is unlocked, DO[23:0], CO1,
CO2, CO3 and CLKOUT output states are controlled by OSS_SEL (See Table 7). May be
used as Link Status or to flag when Video Data is active (ON/OFF).
PASS
42
O, LVCMOS PASS Output (BIST Mode)
PASS = 1, error free transmission
PASS = 0, one or more errors were detected in the received payload
Route to test point for monitoring, or leave open if unused.
Control and Configuration — STRAP PINS
For a High State, use a 10 kΩ pull up to VDDIO; for a Low State, the IO includes an internal pull down. The STRAP pins are read upon
power-up and set device configuration. Pin Number listed along with shared data output name in square brackets.
7
www.national.com
DS92LV2411/DS92LV2412
DS92LV2412 Deserializer Pin Descriptions
DS92LV2411/DS92LV2412
Pin Name
Pin #
I/O, Type
Description
CONFIG[1:0]
10 [DO22],
9 [DO23]
STRAP
00: Control Signal Filter DISABLED
I, LVCMOS 01: Control Signal Filter ENABLED
w/ pull-down 10: Reverse compatibility mode to interface with the DS90UR241 or DS99R241
11: Reverse compatibility mode to interface with the DS90C241
LF_MODE
12 [DO20]
STRAP
SSCG Low Frequency Mode
I, LVCMOS Only required when SSCG is enabled, otherwise LF_MODE condition is a DON’T CARE
w/ pull-down (X).
LF_MODE = 1, SSCG in low frequency mode (CLK = 5-20 MHz)
LF_MODE = 0, SSCG in high frequency mode (CLK = 20-50 MHz)
This can also be controlled by I2C register access.
OS_CLKOUT
11 [DO21]
STRAP
Output CLKOUT Slew Select
I, LVCMOS OS_CLKOUT = 1, Increased CLKOUT slew rate
w/ pull-down OS_CLKOUT = 0, Normal CLKOUT slew rate (default)
This can also be controlled by I2C register access.
OS_DATA
14 [DO19]
STRAP
Output DO[23:0], CO1, CO2, CO3 Slew Select
I, LVCMOS OS_DATA = 1, Increased DO slew rate
w/ pull-down OS_DATA = 0, Normal DO slew rate (default)
This can also be controlled by I2C register access.
OP_LOW
42 [PASS]
STRAP
Outputs held LOW when LOCK = 1
I, LVCMOS NOTE: Do not use any other strap options with this strap function enabled
w/ pull-down OP_LOW = 1: all outputs are held LOW during power up until released by programming
OP_LOW release/set register HIGH.
NOTE: Before the device is powered up, the outputs are in TRI-STATE™
See Figure 24 and Figure 25
OP_LOW = 0: all outputs toggle normally as soon as LOCK goes HIGH (default)
This can also be controlled by I2C register access.
OSS_SEL
17 [DO18]
STRAP
Output Sleep State Select
I, LVCMOS OSS_SEL is used in conjunction with PDB to determine the state of the outputs in Power
w/ pull-down Down (Sleep). (See Table 7).
NOTE: OSS_SEL STRAP CANNOT BE USED IF OP_LOW = 1
This can also be controlled by I2C register access.
RFB
18 [DO17]
STRAP
Clock Output Strobe Edge Select
I, LVCMOS RFB = 1, parallel interface data and control signals are strobed on the rising clock edge.
w/ pull-down RFB = 0, parallel interface data and control signals are strobed on the falling clock edge.
This can also be controlled by I2C register access.
EQ[3:0]
20 [DO15],
STRAP
Receiver Input Equalization
21 [DO14], I, LVCMOS (See Table 4).
22 [DO13], w/ pull-down This can also be controlled by I2C register access.
23 [DO12]
OSC_SEL[2:0] 26 [DO10],
STRAP
Oscillator Selectl
27 [DO9],
I, LVCMOS (See Table 8 and Table 9).
28 [DO8] w/ pull-down This can also be controlled by I2C register access.
SSC[3:0]
MAP_SEL[1:0]
34 [DO6],
35 [DO5],
36 [DO4],
37 [DO3]
40[D],
41 [D]
STRAP
Spread Spectrum Clock Generation (SSCG) Range Select
I, LVCMOS (See Table 5 and Table 6).
w/ pull-down This can also be controlled by I2C register access.
STRAP
Bit mapping reverse compatibility / DS90UR241 Options
I, LVCMOS Pin or Register Control
w/ pull-down Default setting is b'00.
Control and Configuration
PDB
www.national.com
59
I, LVCMOS Power Down Mode Input
w/ pull-down PDB = 1, Des is enabled (normal operation).
Refer to “Power Up Requirements and PDB Pin” in the Applications Information Section.
PDB = 0, Des is in power-down.
When the Des is in the power-down state, the LVCMOS output state is determined by Table
7. Control Registers are RESET.
8
Pin #
I/O, Type
Description
ID[x]
56
I, Analog
I2C Serial Control Bus Device ID Address Select — Optional
Resistor to Ground and 10 kΩ pull-up to 1.8V rail. (See Table 10).
SCL
3
I, LVCMOS
I2C Serial Control Bus Clock Input - Optional
SCL requires an external pull-up resistor to VDDIO.
SDA
2
I/O,
LVCMOS
Open Drain
I2C Serial Control Bus Data Input / Output - Optional
SDA requires an external pull-up resistor to VDDIO.
BISTEN
44
I, LVCMOS BIST Enable Input — Optional
w/ pull-down BISTEN = 0, BIST is disabled (normal operation)
BISTEN = 1, BIST is enabled
RES
47
I, LVCMOS Reserved - tie LOW
w/ pull-down
NC
1, 15, 16,
30, 31, 45,
46, 60
DS92LV2411/DS92LV2412
Pin Name
Not Connected
Leave pin open (float)
Channel-Link II — CML Serial Interface
I, CML
True Input. The input must be AC Coupled with a 0.1 μF capacitor.
50
I, CML
Inverting Input. The input must be AC Coupled with a 0.1 μF capacitor.
51
I, Analog
Common-Mode Filter
VCM center-tap is a virtual ground which may be ac-coupled to ground to increase receiver
common mode noise immunity. Recommended value is 4.7 μF or higher.
ROUT+
52
O, CML
True Output — Receive Signal after the Equalizer
NC if not used or connect to test point for monitor. Requires I2C control to enable.
ROUT-
53
O, CML
Inverting Output — Receive Signal after the Equalizer
NC if not used or connect to test point for monitor. Requires I2C control to enable.
VDDL
29
Power
Logic Power, 1.8 V ±5%
VDDIR
48
Power
Input Power, 1.8 V ±5%
VDDR
43, 55
Power
RX High Speed Logic Power, 1.8 V ±5%
VDDSC
4, 58
Power
SSCG Power, 1.8 V ±5%
VDDPR
57
Power
PLL Power, 1.8 V ±5%
RIN+
49
RINCMF
Power and Ground
VDDCMLO
VDDIO
GND
54
Power
RX High Speed Logic Power, 1.8 V ±5%
13, 24, 38
Power
LVCMOS I/O Power, 1.8 V ±5% OR 3.3 V ±10% (VDDIO)
DAP
Ground
DAP is the large metal contact at the bottom side, located at the center of the LLP package.
Connected to the ground plane (GND) with at least 9 vias.
NOTE: 1 = HIGH, 0 = LOW
The VDD (VDDn and VDDIO) supply ramp should be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms then a capacitor
on the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage.
9
www.national.com
DS92LV2411/DS92LV2412
θJA
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage – VDDn (1.8V)
Supply Voltage – VDDIO
LVCMOS I/O Voltage
Receiver Input Voltage
Driver Output Voltage
Junction Temperature
Storage Temperature
48L LLP Package
Maximum Power Dissipation
Capacity at 25°C
Derate above 25°C
θJC
60L LLP Package
Maximum Power Dissipation
Capacity at 25°C
Derate above 25°C
4.5 °C/W
≥±8 kV
Recommended Operating
Conditions
−0.3V to +2.5V
−0.3V to +4.0V
−0.3V to +(VDDIO + 0.3V)
−0.3V to (VDD + 0.3V)
−0.3V to (VDD + 0.3V)
+150°C
−65°C to +150°C
θJA
24.2 °C/W
θJC
ESD Rating (HBM)
Supply Voltage (VDDn)
LVCMOS Supply
Voltage (VDDIO)
OR
LVCMOS Supply
Voltage (VDDIO)
Operating Free Air
Temperature (TA)
Clock Frequency
Supply Noise (Note 10)
215 mW
1/ θJA mW / °C
28.5 °C/W
2.8 °C/W
Min
1.71
1.71
Nom
1.8
1.8
Max
1.89
1.89
Units
V
V
3.0
3.3
3.6
V
−40
5
+25
+85
50
100
°C
MHz
mVP-P
TBD W
TBD mW / °C
Serializer DC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified. (Note 2, Note 3, Note 4)
Symbol
Parameter
Conditions
Pin/Freq.
Min
Typ
Max
Units
2.2
VDDIO
V
0.65*
VDDIO
VDDIO
V
GND
0.8
V
GND
0.35*
VDDIO
V
LVCMOS INPUT DC SPECIFICATIONS
VDDIO = 3.0 to 3.6V
VIH
High Level Input Voltage
VDDIO = 1.71 to 1.89V
VDDIO = 3.0 to 3.6V
VIL
IIN
Low Level Input Voltage
Input Current
VDDIO = 1.71 to 1.89V
VIN = 0V or VDDIO
VDDIO = 3.0
to 3.6V
DI[23:0],
CI1,CI2,CI3,
CLKIN, PDB,
VODSEL,
RFB,
BISTEN,
CONFIG[1:0]
−15
±1
+15
μA
VDDIO = 1.7
to 1.89V
−15
±1
+15
μA
VODSEL = 0
±205
±280
±355
VODSEL = 1
±320
±420
±520
CML DRIVER DC SPECIFICATIONS
VOD
Differential Output Voltage
VODp-p
Differential Output Voltage
(DOUT+) – (DOUT-)
ΔVOD
Output Voltage Unbalance
RL = 100Ω,
De-emph = disabled,
Figure 2
VODSEL = 0
560
mVp-p
VODSEL = 1
840
mVp-p
RL = 100Ω, De-emph = disabled,
VODSEL = L
1
DOUT+,
VODSEL = 0 DOUTVODSEL = 1
VOS
Offset Voltage – Single-ended RL = 100Ω,
At TP A & B, Figure 1
De-emph = disabled
ΔVOS
Offset Voltage Unbalance
Single-ended
At TP A & B, Figure 1
RL = 100Ω, De-emph = disabled
IOS
Output Short Circuit Current
DOUT+/- = 0V,
De-emph = disabled
RTO
Internal Output Termination
Reistor
www.national.com
mV
VODSEL = 0
DOUT+,
DOUT-
10
80
50
mV
1.65
V
1.575
V
1
mV
−36
mA
100
120
Ω
Parameter
Conditions
Pin/Freq.
Min
Typ
Max
Units
Checker Board
VDD= 1.89V All VDD pins
Pattern,
VDDIO= 1.89V
De-emph = 3kΩ,
VDDIO
VODSEL = H, Figure 9 VDDIO = 3.6V
75
85
mA
3
5
mA
11
15
mA
Checker Board
VDD= 1.89V All VDD pins
Pattern,
VDDIO= 1.89V
De-emph = 6kΩ,
VDDIO
VODSEL = L, Figure 9 VDDIO = 3.6V
65
75
mA
3
5
mA
11
15
mA
VDD= 1.89V All VDD pins
PDB = 0V , (All other
V
= 1.89V
LVCMOS Inputs = 0V) DDIO
VDDIO
VDDIO = 3.6V
40
1000
µA
SUPPLY CURRENT
IDDT1
IDDIOT1
IDDT2
Serializer
Supply Current
(includes load current)
RL = 100 Ω, CLKIN = 50 MHz
IDDIOT2
IDDZ
IDDIOZ
Serializer
Supply Current Power-down
5
10
µA
10
20
µA
Typ
Max
Units
2.0
VDDIO
V
GND
0.8
V
+15
μA
Deserializer DC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Pin/Freq.
Min
3.3 V I/O LVCMOS DC SPECIFICATIONS – VDDIO = 3.0 to 3.6V
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
IIN
Input Current
PDB,
BISTEN
VIN = 0V or VDDIO
VOH
High Level Output Voltage
IOH = −0.5 mA, RDS = L
VOL
Low Level Output Voltage
IOL = +0.5 mA, RDS = L
Output Short Circuit Current
IOS
Output Short Circuit Current
IOZ
TRI-STATE® Output Current
VOUT = 0V, RDS = L
DO[23:0],
CO1, CO2,
CO3,
CLKOUT,
LOCK, PASS
−15
±1
VDDIO0.2
VDDIO
GND
CLKOUT
VOUT = 0V, RDS = H
VOUT = 0V, RDS = L
Outputs
VOUT = 0V, RDS = H
PDB = 0V, OSS_SEL = 0V,
VOUT = 0V or VDDIO
Outputs
V
0.2
V
TBD
mA
TBD
mA
TBD
mA
TBD
mA
−10
+10
µA
0.65*
VDDIO
VDDIO
V
GND
0.35*
VDDIO
V
+15
μA
1.8 V I/O LVCMOS DC SPECIFICATIONS – VDDIO = 1.71 to 1.89V
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
IIN
Input Current
PDB,
BISTEN
VIN = 0V or VDDIO
VOH
High Level Output Voltage
IOH = −0.5 mA, RDS = L
VOL
Low Level Output Voltage
IOL = +0.5 mA, RDS = L
Output Short Circuit Current
IOS
Output Short Circuit Current
IOZ
TRI-STATE Output Current
VOUT = 0V, RDS = L
DO[23:0],
CO1, CO2,
CO3,
CLKOUT,
LOCK, PASS
−15
±1
VDDIO
- 0.2
VDDIO
GND
CLKOUT
VOUT = 0V, RDS = H
VOUT = 0V, RDS = L
Outputs
VOUT = 0V, RDS = H
PDB = 0V, OSS_SEL = 0V,
VOUT = 0V or VDDIO
11
Outputs
-10
V
0.2
V
TBD
mA
TBD
mA
TBD
mA
TBD
mA
+10
µA
www.national.com
DS92LV2411/DS92LV2412
Symbol
DS92LV2411/DS92LV2412
Symbol
Parameter
Conditions
Pin/Freq.
Min
Typ
Max
Units
CML RECEIVER DC SPECIFICATIONS
VTH
VTL
Differential Input Threshold
High Voltage
Differential Input Threshold
Low Voltage
VCM
Common Mode Voltage,
Internal VBIAS
IIN
Input Current
RTI
Internal Input Termination
Resistor
+50
mV
−50
mV
VCM = +1.2V (Internal VBIAS)
RIN+, RIN1.2
V
TBD
-10
+10
µA
TBD
-10
+10
µA
RIN+,
RIN-
80
100
120
Ω
LOOP THROUGH CML DRIVER OUTPUT DC SPECIFICATIONS – EQ TEST PORT
VOD
Differential Output Voltage
VOS
Offset Voltage
Single-ended
RL = 100Ω
ROUT+/-
RL = 100Ω
TBD
mV
TBD
V
SUPPLY CURRENT
IDD1
IDDIO1
IDD2
Deserializer
Supply Current
(includes load current)
CLKOUT = 50 MHz
IDDIO2
IDDZ
IDDIOZ
Deserializer Supply Current
Power Down
VDD= 1.89V
Checker Board
Pattern, RDS = H,
CL = 4pF, Figure 9
VDDIO=1.89V
VDDIO = 3.6V
VDD= 1.89V
All VDD pins
VDDIO
All VDD pins
Random Pattern, RDS
VDDIO =1.89V
= H, CL = 4pF
VDDIO
VDDIO = 3.6V
PDB = 0V, All other
LVCMOS Inputs = 0V
VDD= 1.89V
VDDIO=1.89V
VDDIO = 3.6V
All VDD pins
TBD
TBD
mA
TBD
TBD
mA
TBD
TBD
mA
TBD
mA
TBD
mA
TBD
mA
TBD
TBD
µA
TBD
TBD
µA
100
TBD
µA
Min
Typ
Max
Units
VDDIO
Recommended Serializer Timing for CLKIN
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
tTCP
Transmit Input CLKIN Period
20
T
200
ns
tTCIH
Transmit Input CLKIN High
Time
5 MHz to 50 MHz, Figure 4
0.4T
0.5T
0.6T
ns
tTCIL
Transmit Input CLKIN Low Time
0.4T
0.5T
0.6T
ns
tCLKT
CLKIN Input Transition Time
SSCIN
CLKIN Input – Spread
Spectrum at 50 MHz
2.4
ns
fmod
0.5
35
kHz
fdev
±2
%
Max
Units
Serializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
tLHT
tHLT
tDIS
Parameter
Ser Output Low-to-High
Transition Time, Figure 3
Ser Output High-to-Low
Transition Time, Figure 3
Input Data - Setup Time,
Figure 4
www.national.com
Conditions
Min
Typ
RL = 100Ω, De-emphasis = disabled,
VODSEL = 0
200
ps
RL = 100Ω, De-emphasis = disabled,
VODSEL = 1
200
ps
RL = 100Ω, De-emphasis = disabled,
VODSEL = 0
200
ps
RL = 100Ω, De-emphasis = disabled,
VODSEL = 1
200
ps
DI[23:0], CI1, CI2, CI3 to CLKIN
12
2
ns
Parameter
tDIH
Input Data - Hold Time,
Figure 4
tXZD
Ser Ouput Active to OFF Delay,
Figure 6
tPLD
Serializer PLL Lock Time,
Figure 5
tSD
Conditions
Min
CLKIN to DI[23:0], CI1, CI2, CI3
Typ
Max
2
Units
ns
8
15
ns
RL = 100Ω
1.4
10
ms
Serializer Delay - Latency,
Figure 7
RL = 100Ω
144*T
145
ns
tDJIT
Ser Output Total Jitter,
Figure 8
RL = 100Ω, De-Emph = disabled,
RANDOM pattern
λSTXBW
δSTX
TBD
UI
Serializer Jitter Transfer
Function -3 dB Bandwidth
TBD
kHz
Serializer Jitter Transfer
Function Peaking
TBD
dB
Deserializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
tRCP
CLK Output Period
tRDC
CLK Output Duty Cycle
tCLH
LVCMOS
Low-to-High
Transition Time, Figure 10
tCHL
tROS
tROH
LVCMOS
High-to-Low
Transition Time, Figure 10
Conditions
Pin/Freq.
Typ
Max
Units
13.3
T
100
ns
45
50
55
%
2.5
3.5
ns
VDDIO = 1.71 to 1.89V
CL = 8 pF, OS_CLKOUT/
DATA = H
1.5
2.5
ns
VDDIO = 3.0 to 3.6V
CL = 8 pF, OS_CLKOUT/
DATA = L
2.5
3.5
ns
VDDIO = 3.0 to 3.6V
CL = 8 pF, OS_CLKOUT/
DATA = H
1.5
2.5
ns
2.5
3.5
ns
VDDIO = 1.71 to 1.89V
CL = 8 pF, OS_CLKOUT/
DATA = H
1.5
2.5
ns
VDDIO = 3.0 to 3.6V
CL = 8 pF), OS_CLKOUT/
DATA = L
2.5
3.5
ns
VDDIO = 3.0 to 3.6V
CL = 8 pF, OS_CLKOUT/
DATA = H
1.5
2.5
ns
tRCP = tTCP
CLKOUT
VDDIO = 1.71 to 1.89V,
CL = 8 pF, OS_CLKOUT/
DATA = L
VDDIO = 1.71 to 1.89V
CL = 8 pF, OS_CLKOUT/
DATA = L
CLKOUT
CLKOUT
Data Valid before CLKOUT –
Set Up Time, Figure 14
VDDIO = 1.71 to 1.89V or
VDDIO = 3.0 to 3.6V
CL = 8 pF (lumped load)
RFB =
DO[23:0], CO1, CO2,
CO3
Data Valid after CLKOUT –
Hold Time, Figure 14
VDDIO = 1.71 to 1.89V or
VDDIO = 3.0 to 3.6V
CL = 8 pF (lumped load)
DO[23:0], CO1, CO2,
CO3
13
Min
0.3
0.5
UI
0.4
0.5
UI
www.national.com
DS92LV2411/DS92LV2412
Symbol
DS92LV2411/DS92LV2412
Symbol
tXZR
tDDLT
Parameter
Conditions
Pin/Freq.
Active to OFF Delay, Figure 12 OSS_SEL = 0
Deserializer Lock Time,
Figure 13
Min
Typ
DO[23:0], CO1, CO2,
CO3, LOCK, PASS,
CLKOUT
SSC[3:0] = OFF,
(Note 6)
CLKOUT = 5to 50MHz
SSC[3:0] = ON,
(Note 6)
tDD
Des Delay - Latency, Figure 11
tDPJ
Des Period Jitter
CLKOUT = 5 to 50 MHz
140*T
SSC[3:0] = OFF,
(Note 8)
CLKOUT = 5 to 50 MHz
TBD
CLKOUT = 5 to 50 MHz
tDCCJ
Des Cycle-to-Cycle Jitter
SSC[3:0] = OFF,
(Note 9)
tRJIT
Des Input Jitter Tolerance,
Figure 16
EQ = OFF
CLKOUT = 5 to 50 MHz
Max
Units
TBD
ns
10
ms
10
ms
TBD
ns
±1
ns
UI
TBD
CLKOUT = 5to 50 MHz
UI
±300
ps
0.5
TBD
UI
TBD
10
ns
BIST Mode
tPASS
BIST PASS Valid Time,
BISTEN = 1, Figure 17
SSCG Mode
fDEV
fMOD
Spread Spectrum
Clocking Deviation
Frequency
CLKOUT = 5 to 50 MHz,
SSC[3:0] = ON
±0.5
±2
%
Spread Spectrum
Clocking Modulation
Frequency
CLKOUT = 5 to 50 MHz,
SSC[3:0] = ON
8
100
kHz
Max
Units
100
kHz
Recommended Timing for the Serial Control Bus
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
fSCL
SCL Clock Frequency
Standard Mode
tLOW
SCL Low Period
Standard Mode
4.7
us
Fast Mode
1.3
us
Standard Mode
4.0
us
tHIGH
SCL High Period
Fast Mode
0.6
us
tHD;STA
Hold time for a start or a
repeated start condition,
Figure 18
Standard Mode
4.0
us
0.6
us
Set Up time for a start or a
repeated start condition,
Figure 18
Standard Mode
4.7
us
0.6
us
Data Hold Time,
Figure 18
Standard Mode
0
3.45
us
Fast Mode
0
0.9
us
Data Set Up Time,
Figure 18
Standard Mode
250
ns
Fast Mode
100
ns
tSU;STO
Set Up Time for STOP
Condition, Figure 18
Standard Mode
4.0
us
Fast Mode
0.6
us
tBUF
Bus Free Time
Between STOP and START,
Figure 18
Standard Mode
4.7
us
1.3
us
SCL & SDA Rise Time,
Figure 18
Standard Mode
1000
ns
Fast Mode
300
ns
SCL & SDA Fall Time,
Figure 18
Standard Mode
300
ns
Fast mode
300
ns
tSU:STA
tHD;DAT
tSU;DAT
tr
tf
www.national.com
Fast Mode
Fast Mode
Fast Mode
14
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
VIH
Input High Level
SDA and SCL
2.2
VIL
Input Low Level Voltage
SDA and SCL
GND
VHY
Input Hysteresis
Typ
Max
Units
VDD 3.3V
V
0.8
>50
VOL
SDA, IOL = 3mA
Iin
SDA or SCL, Vin = VDDIO or GND
V
mV
0
0.4
V
-15
+15
µA
SDA, RPU = X, Cb ≤ 400pF
tR
SDA RiseTime – READ
40
ns
tF
SDA Fall Time – READ
25
ns
tSU;DAT
Set Up Time — READ
520
ns
tHD;DAT
Hold Up Time — READ
55
ns
tSP
Input Filter
Cin
Input Capacitance
SDA or SCL
50
ns
<5
pF
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability
and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in
the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the
device should not be operated beyond such conditions.
Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 3: Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at the time of
product characterization and are not guaranteed.
Note 4: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, ΔVOD,
VTH and VTL which are differential voltages.
Note 5: When the Serializer output is at TRI-STATE the Deserializer will lose PLL lock. Resynchronization / Relock must occur before data transfer require tPLD
Note 6: tPLD and tDDLT is the time required by the serializer and deserializer to obtain lock when exiting power-down state with an active clock.
Note 7: UI – Unit Interval is equivalent to one serialized data bit width (1UI = 1 / 28*CLK). The UI scales with clock frequency.
Note 8: tDPJ is the maximum amount the period is allowed to deviate over many samples.
Note 9: tDCCJ is the maximum amount of jitter between adjacent clock cycles.
Note 10: Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC coupled to the VDDn (1.8V) supply with amplitude = 100
mVp-p measured at the device VDDn pins. Bit error rate testing of input to the Ser and output of the Des with 10 meter cable shows no error when the noise
frequency on the Ser is less than 750 kHz. The Des on the other hand shows no error when the noise frequency is less than 400 kHz.
Note 11: Specification is guaranteed by characterization and is not tested in production.
Note 12: Specification is guaranteed by design and is not tested in production.
15
www.national.com
DS92LV2411/DS92LV2412
DC and AC Serial Control Bus Characteristics
DS92LV2411/DS92LV2412
AC Timing Diagrams and Test Circuits
30065346
FIGURE 1. Serializer Test Circuit
30065330
FIGURE 2. Serializer Output Waveforms
30065347
FIGURE 3. Serializer Output Transition Times
30065331
FIGURE 4. Serializer Input CLKIN Waveform and Set and Hold Times
www.national.com
16
DS92LV2411/DS92LV2412
30065348
FIGURE 5. Serializer Lock Time
30065349
FIGURE 6. Serializer Disable Time
30065310
FIGURE 7. Serializer Latency Delay
17
www.national.com
DS92LV2411/DS92LV2412
30065350
FIGURE 8. Serializer Output Jitter
30065332
FIGURE 9. Checkerboard Data Pattern
30065305
FIGURE 10. Deserializer LVCMOS Transition Times
30065311
FIGURE 11. Deserializer Delay – Latency
www.national.com
18
DS92LV2411/DS92LV2412
30065313
FIGURE 12. Deserializer Disable Time (OSS_SEL = 0)
30065314
FIGURE 13. Deserializer PLL Lock Times and PDB TRI-STATE™ Delay
30065335
FIGURE 14. Deserializer Output Data Valid (Setup and Hold) Times with SSCG = Off
19
www.national.com
DS92LV2411/DS92LV2412
30065334
FIGURE 15. Deserializer Output Data Valid (Setup and Hold) Times with SSCG = On
30065316
FIGURE 16. Receiver Input Jitter Tolerance
30065352
FIGURE 17. BIST PASS Waveform
www.national.com
20
DS92LV2411/DS92LV2412
30065336
FIGURE 18. Serial Control Bus Timing Diagram
21
www.national.com
DS92LV2411/DS92LV2412
Functional Description
DS92LV2412 Des Modes
The DS92LV2411 / DS92LV2412 chipset transmits and receives 24-bits of data and 3 control signals over a single serial
CML pair operating at 140 Mbps to 1.4 Gbps. The serial
stream also contains an embedded clock, video control signals and the DC-balance information which enhances signal
quality and supports AC coupling.
The Des can attain lock to a data stream without the use of a
separate reference clock source, which greatly simplifies system complexity and overall cost. The Des also synchronizes
to the Ser regardless of the data pattern, delivering true automatic “plug and lock” performance. It can lock to the incoming serial stream without the need of special training patterns
or sync characters. The Des recovers the clock and data by
extracting the embedded clock information, validating and
then deserializing the incoming data stream providing a parallel LVCMOS video bus to the display or ASIC/FPGA.
The DS92LV2411 / DS92LV2412 chipset can operate in 24bit color depth (with DE, HS, VS encoded within the serial data
stream). In 18–bit color applications, the three video control
signals maybe sent encoded within the serial bit stream (restrictions apply) along with six additional general purpose
signals.
Block Diagrams for the chipset are shown at the beginning of
this datasheet.
CONFIG1 CONFIG0 MODE
SER DEVICE
L
L
Normal Mode,
Control Signal
Filter disabled
DS92LV2411,
DS92LV2411,
DS92LV0421,
DS92LV0411
L
H
Normal Mode,
Control Signal
Filter enabled
DS92LV2411,
DS92LV2411,
DS92LV0421,
DS92LV0411
H
L
Reverse
Compatibility
Mode
DS90UR241
H
H
Reverse
Compatibility
Mode
DS90C241
VIDEO CONTROL SIGNAL FILTER — SER & DES
When operating the devices in Normal Mode, the Control Signals have the following restrictions:
• Normal Mode with Control Signal Filter Enabled: Control
Signal 1 and Control Signal 2 — Only 2 transitions per 130
clock cycles are transmitted, the transition pulse must be
3 parallel clocks or longer.
• Normal Mode with Control Signal Filter Disabled: Control
Signal 1 and Control Signal 2 — Only 2 transitions per 130
clock cycles are transmitted, no restriction on minimum
transition pulse.
• Control Signal 3 — Only 1 transition per 130 clock cycles
is transmitted , minimum pulse width is 130 clock cycles.
Control Signals are defined as low frequency signals with limited transition. Glitches of a control signal can cause a visual
error in display applications. This feature allows for the
chipset to validate and filter out any high frequency noise on
the control signals. See Figure.
Data Transfer
The DS92LV2411 / DS92LV2412 chipset will transmit and
receive a pixel of data in the following format: C1 and C0 represent the embedded clock in the serial stream. C1 is always
HIGH and C0 is always LOW. The remaining 26 bit spaces
contain the scrambled, encoded and DC-Balanced serial data.
SER & DES OPERATING MODES AND REVERSE
COMPATIBILITY (CONFIG[1:0])
The DS92LV2411 / DS92LV2412 chipset is compatible with
other single serial lane Channel Link II or FPD-Link II devices.
Configuraiton modes are provided for reverse compatibility
with the DS90C241 / DS90C124 and also the DS90UR241 /
DS90UR124 by setting the respective mode with the CONFIG
[1:0] pins on the Ser or Des as shown in Table and Table. This
selection also determines whether the Control Signal Filter
feature is enabled or disabled in the Normal mode. These
configuration modes are selectable the control pins only.
SERIALIZER Functional Description
The Ser converts a wide parallel input bus to a single serial
output data stream, and also acts as a signal generator for
the chipset Built In Self Test (BIST) mode. The device can be
configured via external pins or through the optional serial
control bus. The Ser features enhance signal quality on the
link by supporting: a selectable VOD level, a selectable deemphasis signal conditioning and also the Channel Link II
data coding that provides randomization, scrambling, and DC
Balanacing of the data. The Ser includes multiple features to
reduce EMI associated with display data transmission. This
includes the randomization and scrambling of the data and
also the system spread spectrum clock support. The Ser features power saving features with a sleep mode, auto stop
clock feature, and optional LVCMOS (1.8 V) parallel bus compatibility.
See also the Functional Description of the chipset's serial
control bus and BIST modes.
TABLE 1. DS92LV2411 Ser Modes
CONFIG1 CONFIG0 MODE
DES DEVICE
L
L
Normal Mode,
Control Signal
Filter disabled
DS92LV2412,
DS92LV2412,
DS92LV0422,
DS92LV0412
L
H
Normal Mode,
Control Signal
Filter enabled
DS92LV2412,
DS92LV2412,
DS92LV0422,
DS92LV0412
H
L
Reverse
Compatibility
Mode
DS90UR124,
DS99R124
Reverse
Compatibility
Mode
DS90C124
H
H
www.national.com
EMI Reduction Features
Data Randomization & Scrambling
Channel Link II Ser / Des feature a 3 step encoding process
which enables the use of AC coupled interconnects and also
helps to manage EMI. The serializer first passes the parallel
data through a scrambler which randomizes the data. The
randomized data is then DC balanced. The DC balanced and
22
DS92LV2411/DS92LV2412
randomized data then goes through a bit shuffling circuit and
is transmitted out on the serial line. This encoding process
helps to prevent static data patterns on the serial stream. The
resulting frequency content of the serial stream ranges from
the parallel clock frequency to the nyquist rate. For example,
if the Ser / Des chip set is operating at a parallel clock frequency of 50 MHz, the resulting frequency content of serial
stream ranges from 50 MHz to 700 MHz ( 50 MHz *28 bits =
1.4 Gbps / 2 = 700 MHz ).
Ser — Spread Spectrum Compatibility
The Ser CLKIN is capable of tracking spread spectrum clocking (SSC) from a host source. The CLKIN will accept spread
spectrum tracking up to 35 kHz modulation and ±0.5, ±1 or
±2% deviations (center spread). The maximum conditions for
the CLKIN input are: a modulation frequency of 35 kHz and
amplitude deviations of ±2% (4% total).
30065360
FIGURE 19. De-Emph vs. R value
Integrated Signal Conditioning Features — Ser
Ser — VOD Select (VODSEL)
The Ser differential output voltage may be increased by setting the VODSEL pin High. When VODSEL is Low, the VOD
is at the standard (default) level. When VODSEL is High, the
VOD is increased in level. The increased VOD is useful in
extremely high noise environments and also on extra long
cable length applications. When using de-emphasis it is recommended to set VODSEL = H to avoid excessive signal
attenuation especially with the larger de-emphasis settings.
This feature may be controlled by the external pin or by register.
Power Saving Features
Ser — Power Down Feature (PDB)
The Ser has a PDB input pin to ENABLE or POWER DOWN
the device. This pin is controlled by the host and is used to
save power, disabling the link when the it is not needed. In
the POWER DOWN mode, the high-speed driver outputs are
both pulled to VDD and present a 0V VOD state. Note – in
POWER DOWN, the optional Serial Bus Control Registers
are RESET.
Ser — Stop Clock Feature
The Ser will enter a low power SLEEP state when the CLKIN
is stopped. A STOP condition is detected when the input clock
frequency is less than 3 MHz. The clock should be held at a
static Low or high state. When the CLKIN starts again, the Ser
will then lock to the valid input clock and then transmits the
serial data to the Des. Note – in STOP CLOCK SLEEP, the
optional Serial Bus Control Registers values are RETAINED.
TABLE 2. Differential Output Voltage
Input
Effect
VODSEL
VOD
mV
VOD
mVp-p
H
±420
840
L
±280
560
Ser — De-Emphasis (De-Emph)
The De-Emph pin controls the amount of de-emphasis beginning one full bit time after a logic transition that the Ser
drives. This is useful to counteract loading effects of long or
lossy cables. This pin should be left open for standard switching currents (no de-emphasis) or if controlled by register. Deemphasis is selected by connecting a resistor on this pin to
ground, with R value between 0.5 kΩ to 1 MΩ, or by register
setting. When using De-Emphasis it is recommended to set
VODSEL = H.
1.8V or 3.3V VDDIO Operation
The Ser parallel bus and Serial Bus Interface can operate with
1.8 V or 3.3 V levels (VDDIO) for host compatibility. The 1.8 V
levels will offer lower noise (EMI) and also a system power
savings.
Ser — Pixel Clock Edge Select (RFB)
The RFB pin determines the edge that the data is latched on.
If RFB is High, input data is latched on the Rising edge of the
CLKIN. If RFB is Low, input data is latched on the Falling edge
of the CLKIN. Ser and Des maybe set differently. This feature
may be controlled by the external pin or by register.
TABLE 3. De-Emphasis Resistor Value
Resistor Value (kΩ)
De-Emphasis Setting
Open
Disabled
0.6
- 12 dB
1.0
- 9 dB
2.0
- 6 dB
5.0
- 3 dB
Optional Serial Bus Control
Please see the following section on the optional Serial Bus
Control Interface.
Optional BIST Mode
Please see the following section on the chipset BIST mode
for details.
DESERIALIZER Functional Description
The Des converts a single input serial data stream to a wide
parallel output bus, and also provides a signal check for the
chipset Built In Self Test (BIST) mode. The device can be
configured via external pins and strap pins or through the optional serial control bus. The Des features enhance signal
23
www.national.com
DS92LV2411/DS92LV2412
quality on the link with an integrated equalizer on the serial
input and Channel Link II data encoding which provides randomization, scrambling, and DC balanacing of the data. The
Des includes multiple features to reduce EMI associated with
data transmission. This includes the randomization and
scrambling of the data, the output spread spectrum clock
generation (SSCG) support and output clock and data slew
rate select. The Des features power saving features with a
power down mode, and optional LVCMOS (1.8 V) interface
compatibility.
EMI Reduction Features
Integrated Signal Conditioning Features — Des
Des — Output Slew Rate Select (OS_CLKOUT/OS_DATA)
The parallel data outputs and clock outputs of the deserializer
feature selectable output slew rates. The slew rate of the
CLKOUT pin is controlled by the strap pin or register
OS_CLKOUT, while the data outputs (DO[23:0] and CO[3:1])
are controlled by the strap pin or register OS_DATA. When
OS_CLKOUT/DATA = HIGH, the maxium slew rate is selected. When the OS_CLKOUT/DATA = LOW, the minimum slew
rate is selected. Use the higher slew rate when driving longer
traces or a heavier capacitive load.
Des — Input Equalizer Gain (EQ)
The Des can enable receiver input equalization of the serial
stream to increase the eye opening to the Des input. Note this
function cannot be seen at the RxIN+/- input but can be observed at the serial test port (ROUT+/-) enabled via the Serial
Bus control registers. The equalization feature may be controlled by the external pin or by register.
Des — Common Mode Filter Pin (CMF) — Optional
The Des provides access to the center tap of the internal termination. A capacitor may be placed on this pin for additional
common-mode filtering of the differential pair. This can be
useful in high noise environments for additional noise rejection capability. A 4.7 µF capacitor may be connected to this
pin to Ground.
TABLE 4. Receiver Equalization Configuration Table
Des — SSCG Generation — Optional
The Des provides an internally generated spread spectrum
clock (SSCG) to modulate its outputs. Both clock and data
outputs are modulated. This will aid to lower system EMI.
Output SSCG deviations to ±2% (4% total) at up to 100 kHz
modulations is available. See Table 5. This feature may be
controlled by external STRAP pins or by register.
INPUTS
EQ3
EQ2
L
L
L
L
H
Effect
EQ1
EQ0
L
L
H
~1.5 dB
L
H
H
~3 dB
H
L
H
~4.5 dB
H
H
H
~6 dB
L
L
H
~7.5 dB
H
L
H
H
~9 dB
H
H
L
H
~10.5 dB
H
H
H
H
~12 dB
X
X
L
OFF*
X
* Default Setting is EQ = Off
TABLE 5. SSCG Configuration (LF_MODE = L) — Des Output
SSC[3:0] Inputs
LF_MODE = L (20 - 50 MHz)
Result
SSC3
SSC2
SSC1
SSC0
fdev (%)
fmod (kHz)
L
L
L
L
L
L
L
NA
Disable
H
±0.5
L
L
H
L
±1.0
L
L
H
H
±1.5
L
H
L
L
±2.0
L
H
L
H
±0.5
L
H
H
L
±1.0
L
H
H
H
±1.5
H
L
L
L
±2.0
H
L
L
H
±0.5
H
L
H
L
±1.0
H
L
H
H
±1.5
H
H
L
L
±2.0
H
H
L
H
±0.5
H
H
H
L
±1.0
H
H
H
H
±1.5
www.national.com
24
CLK/2168
CLK/1300
CLK/868
CLK/650
SSC[3:0] Inputs
LH_MODE = H (5 - 20 MHz)
Result
SSC3
SSC2
SSC1
SSC0
fdev (%)
fmod (kHz)
L
L
L
L
L
L
L
NA
Disable
H
±0.5
L
L
H
L
±1.0
L
L
H
H
±1.5
L
H
L
L
±2.0
L
H
L
H
±0.5
L
H
H
L
±1.0
L
H
H
H
±1.5
H
L
L
L
±2.0
H
L
L
H
±0.5
H
L
H
L
±1.0
H
L
H
H
±1.5
H
H
L
L
±2.0
H
H
L
H
±0.5
H
H
H
L
±1.0
H
H
H
H
±1.5
CLK/620
CLK/370
CLK/258
CLK/192
tus. Note – in POWER DOWN, the optional Serial Bus Control
Registers are RESET.
Des — Stop Stream SLEEP Feature
The Des will enter a low power SLEEP state when the input
serial stream is stopped. A STOP condition is detected when
the embedded clock bits are not present. When the serial
stream starts again, the Des will then lock to the incoming
signal and recover the data. Note – in STOP STREAM
SLEEP, the optional Serial Bus Control Registers values are
RETAINED.
30065333
Des — CLOCK-DATA RECOVERY STATUS FLAG (LOCK)
and OUTPUT STATE SELECT (OSS_SEL)
When PDB is driven HIGH, the CDR PLL begins locking to
the serial input and LOCK goes from TRI-STATE to LOW
(depending on the value of the OSS_SEL setting). After the
DS92LV2412 completes its lock sequence to the input serial
data, the LOCK output is driven HIGH, indicating valid data
and clock recovered from the serial input is available on the
parallel bus and clock outputs. The CLKOUT output is held at
its current state at the change from OSC_CLK (if this is enabled via OSC_SEL) to the recovered clock (or vice versa).
If there is a loss of clock from the input serial stream, LOCK
is driven Low and the state of the outputs are based on the
OSS_SEL setting (STRAP PIN configuration or register).
FIGURE 20. SSCG Waveform
1.8V or 3.3V VDDIO Operation
The Des parallel bus and Serial Bus Interface can operate
with 1.8 V or 3.3 V levels (VDDIO) for target host compatibility.
The 1.8 V levels will offer a lower noise (EMI) and also a system power savings.
Power Saving Features
Des — PowerDown Feature (PDB)
The Des has a PDB input pin to ENABLE or POWER DOWN
the device. This pin can be controlled by the system to save
power, disabling the Des when the display is not needed. An
auto detect mode is also available. In this mode, the PDB pin
is tied High and the Des will enter POWER DOWN when the
serial stream stops. When the serial stream starts up again,
the Des will lock to the input stream and assert the LOCK pin
and output valid data. In POWER DOWN mode, the Data and
CLKOUT output states are determined by the OSS_SEL sta-
Des — Oscillator Output — Optional
The Des provides an optional clock output when the input
clock (serial stream) has been lost. This is based on an internal oscillator. The frequency of the oscillator may be selected.
This feature may be controlled by the external pin or by register. See Table 8 and Table 9.
25
www.national.com
DS92LV2411/DS92LV2412
TABLE 6. SSCG Configuration (LF_MODE = H) — Des Output
DS92LV2411/DS92LV2412
TABLE 7. OSS_SEL and PDB Configuration — Des Outputs
INPUTS
Serial
Input
PDB
X
X
Static
Static
Active
OUTPUTS
OSS_SEL
CLKOUT
DO[23:0], CO1,
CO2, CO3
LOCK
PASS
L
L
Z
Z
Z
Z
L
H
L
L
L
H
H
L
Z
Z
L
H
H
H
L
L
L
H
H
X
Active
Active
H
H
TABLE 8. OSC (Oscillator) Mode — Des Output
INPUTS
OUTPUTS
Embedded CLK
CLKOUT
DO[23:0]/CO1/CO2/CO3
LOCK
PASS
NOTE *
OSC
Output
L
L
H
Present
Toggling
Active
H
H
* NOTE — Absent and OSC_SEL ≠ 000
30065340
FIGURE 21. Des Outputs with Output State Select Low (OSS_SEL = L)
www.national.com
26
DS92LV2411/DS92LV2412
30065353
FIGURE 22. Des Outputs with Output State Select High (OSS_SEL = H)
27
www.national.com
DS92LV2411/DS92LV2412
TABLE 9. OSC_SEL (Oscillator) Configuration
OSC_SEL[2:0] INPUTS
CLKOUT Oscillator Frequency
OSC_SEL2
OSC_SEL1
OSC_SEL0
L
L
L
Off – Feature Disabled – Default
L
L
H
50 MHz ±40%
L
H
L
25 MHz ±40%
L
H
H
16.7 MHz ±40%
H
L
L
12.5 MHz ±40%
H
L
H
10 MHz ±40%
H
H
L
8.3 MHz ±40%
H
H
H
6.3 MHz ±40%
30065354
FIGURE 23. Des Outputs with Output State High and CLK Output Oscillator Option Enabled
Other features should be selected through the I2C
register interface.
2. The OSS_SEL feature is not available when OP_LOW is
enabled.
Outputs DO[23:0], CO[3:1] and CLKOUT are in TRI-STATE™
before PDB toggles HIGH because the OP-LOW strap value
has not been recognized until the DS92LV2412 powers up.
Figure 24 shows the user controlled release of the OP_LOW
and automatic reset of OP_LOW set on the falling edge of
LOCK. Figure 25 shows the user controlled release of
OP_LOW and manual reset of OP_LOW set. Note manual
reset of OP_LOW can only occur when LOCK is HIGH.
Des — OP_LOW — Optional
The OP_LOW feature is used to hold the LVCMOS outputs,
except for the LOCK output, at a LOW state. When the
OP_LOW feature is enabled, the LVCMOS outputs will be
held at logic LOW while LOCK = LOW. The user must toggle
the OP_LOW Set/Reset register bit to release the outputs to
the normal toggling state. Note that the release of the outputs
can only occur when LOCK is HIGH. The OP_LOW strap option is assigned to the PASS pin, at pin location 42.
Restrictions on other straps:
1. Other strap options should not be used in order to keep
the data and clock outputs at a true logic LOW state.
www.national.com
28
DS92LV2411/DS92LV2412
30065365
FIGURE 24. OP_LOW Auto Set
30065366
FIGURE 25. OP_LOW Manual Set/Reset
downstream devices. The Des output does not need to use
the same edge as the Ser input. This feature may be controlled by the external pin or by register.
Des — Clock Edge Select (RFB)
The RFB pin determines the edge that the data is strobed on.
If RFB is High, output data is strobed on the Rising edge of
the CLKOUT. If RFB is Low, data is strobed on the Falling
edge of the CLKOUT. This allows for inter-operability with
29
www.national.com
DS92LV2411/DS92LV2412
the incoming serial payloads for errors. If an error in the payload (1 to 24) is detected, the PASS pin will switch low for one
half of the clock period. During the BIST test, the PASS output
can be monitored and counted to determine the payload error
rate.
Step 3: To Stop the BIST mode, the Des BISTEN pin is set
Low. The Des stops checking the data and the final test result
is held on the PASS pin. If the test ran error free, the PASS
output will be High. If there was one or more errors detected,
the PASS output will be Low. The PASS output state is held
until a new BIST is run, the device is RESET, or Powered
Down. The BIST duration is user controlled by the duration of
the BISTEN signal.
Step 4: To return the link to normal operation, the Ser BISTEN
input is set Low. The Link returns to normal operation.
Figure 27 shows the waveform diagram of a typical BIST test
for two cases. Case 1 is error free, and Case 2 shows one
with multiple errors. In most cases it is difficult to generate
errors due to the robustness of the link (differential data transmission etc.), thus they may be introduced by greatly extending the cable length, faulting the interconnect, reducing signal
condition enhancements (De-Emphasis, VODSEL, or Rx
Equalization).
Des — Control Signal Filter — Optional
The deserializer provides an optional Control Signal (C3, C2,
C1) filter that monitors the three control signals and eliminates
any pulses or glitches that are 1 or 2 parallel clock periods
wide. Control signals must be 3 parallel clock periods wide (in
its HIGH or LOW state, regardless of which state is active).
This is set by the CONFIG[1:0] strap option or by I2C register
control.
Des — SSCG Low Frequency Optimization (LF_Mode)
Text to come. This feature may be controlled by the external
pin or by Register.
Des — Strap Input Pins
Configuration of the device maybe done via configuration input pins and the STRAP input pins, or via the Serial Control
Bus. The STRAP input pins share select parallel bus output
pins. They are used to load in configuration values during the
initial power up sequence of the device. Only a pull-up on the
pin is required when a HIGH is desired. By default the pad
has an internal pull down, and will bias Low by itself. The recommended value of the pull up is 10 kΩ to VDDIO; open (NC)
for Low, no pull-down is required (internal pull-down). If using
the Serial Control Bus, no pull ups are required.
Optional Serial Bus Control
Please see the following section on the optional Serial Bus
Control Interface.
Optional BIST Mode
Please see the following section on the chipset BIST mode
for details.
Built In Self Test (BIST)
An optional At-Speed Built In Self Test (BIST) feature supports the testing of the high-speed serial link. This is useful in
the prototype stage, equipment production, in-system test
and also for system diagnostics. In the BIST mode only a input
clock is required along with control to the Ser and Des BISTEN input pins. The Ser outputs a test pattern (PRBS7) and
drives the link at speed. The Des detects the PRBS7 pattern
and monitors it for errors. A PASS output pin toggles to flag
any payloads that are received with 1 to 24 errors. Upon completion of the test, the result of the test is held on the PASS
output until reset (new BIST test or Power Down). A high on
PASS indicates NO ERRORS were detected. A Low on PASS
indicates one or more errors were detected. The duration of
the test is controlled by the pulse width applied to the Des
BISTEN pin.
Inter-operability is supported between this Channel Link II device and all Channel Link II generations (Gen 1/2/3) — see
respective datasheets for details on entering BIST mode and
control.
Sample BIST Sequence
See Figure 26 for the BIST mode flow diagram.
Step 1: Place the DS92LV2411 Ser in BIST Mode by setting
Ser BISTEN = H. For the DS92LV2411 Ser or DS99R421
Channel Link II Ser BIST Mode is enabled via the BISTEN
pin. A CLKIN is required for BIST. When the Des detects the
BIST mode pattern and command (DCA and DCB code) the
data and control signal outputs are shut off.
Step 2: Place the DS92LV2412 Des in BIST mode by setting
the BISTEN = H. The Des is now in the BIST mode and checks
www.national.com
30065343
FIGURE 26. BIST Mode Flow Diagram
BER Calculations
It is possible to calculate the approximate Bit Error Rate
(BER). The following is required:
• Clock Frequency (MHz)
• BIST Duration (seconds)
• BIST test Result (PASS)
The BER is less than or equal to one over the product of 24
times the CLK rate times the test duration. If we assume a 50
MHz clock, a 10 minute (600 second) test, and a PASS, the
BERT is ≤ 1.39 X 10E-12
The BIST mode runs a check on the data payload bits. The
LOCK pin also provides a link status. It the recovery of the C0
and C1 bits does not reconstruct the expected clock signal,
the LOCK pin will switch Low. The combination of the LOCK
and At-Speed BIST PASS pin provides a powerful tool for
system evaluation and performance monitoring.
30
DS92LV2411/DS92LV2412
30065364
FIGURE 27. BIST Waveforms
31
www.national.com
DS92LV2411/DS92LV2412
To communicate with a remote device, the host controller
(master) sends the slave address and listens for a response
from the slave. This response is referred to as an acknowledge bit (ACK). If a slave on the bus is addressed correctly,
it Acknowledges (ACKs) the master by driving the SDA bus
low. If the address doesn't match a device's slave address, it
Not-acknowledges (NACKs) the master by letting SDA be
pulled High. ACKs also occur on the bus when data is being
transmitted. When the master is writing data, the slave ACKs
after every data byte is successfully received. When the master is reading data, the master ACKs after every data byte is
received to let the slave know it wants to receive another data
byte. When the master wants to stop reading, it NACKs after
the last data byte and creates a stop condition on the bus. All
communication on the bus begins with either a Start condition
or a Repeated Start condition. All communication on the bus
ends with a Stop condition. A READ is shown in Figure 30
and a WRITE is shown in Figure 31.
If the Serial Bus is not required, the three pins may be left
open (NC).
Optional Serial Bus Control
The Ser and Des may also be configured by the use of a serial
control bus that is I2C protocol compatible. By default, the I2C
reg_0x00'h is set to 00'h and all configuration is set by control/
strap pins. A write of 01'h to reg_0x00'h will enable/allow configuration by registers; this will override the control/strap pins.
Multiple devices may share the serial control bus since multiple addresses are supported. See Figure 28.
The serial bus is comprised of three pins. The SCL is a Serial
Bus Clock Input. The SDA is the Serial Bus Data Input / Output signal. Both SCL and SDA signals require an external pull
up resistor to VDDIO. For most applications a 4.7 k pull up resistor to VDDIO may be used. The resistor value may be
adjusted for capacitive loading and data rate requirements.
The signals are either pulled High, or driven Low.
TABLE 10. ID[x] Resistor Value – DS92LV2411 Ser
Resistor
RID kΩ
30065341
FIGURE 28. Serial Control Bus Connection
Address
7'b
Address
8'b
0 appended
(WRITE)
0.47
7b' 110 1001 (h'69)
8b' 1101 0010 (h'D2)
2.7
7b' 110 1010 (h'6A)
8b' 1101 0100 (h'D4)
8.2
7b' 110 1011 (h'6B)
8b' 1101 0110 (h'D6)
Open
7b' 110 1110 (h'6E)
8b' 1101 1100 (h'DC)
TABLE 11. ID[x] Resistor Value – DS92LV2412 Des
The third pin is the ID[X] pin. This pin sets one of five possible
device addresses. Three different connections are possible.
The pin may be tied to ground. The pin may be pulled to
VDD (1.8V, NOT VDDIO)) with a 10 kΩ resistor. Or a 10 kΩ pull
up resistor (to VDD 1.8V, NOT VDDIO)) and a pull down resistor
of the recommended value to set other three possible addresses may be used. See Table 10 for the Ser and Table
11 for the Des.
The Serial Bus protocol is controlled by START, START-Repeated, and STOP phases. A START occurs when SCL
transitions Low while SDA is High. A STOP occurs when SDA
transition High while SCL is also HIGH. See Figure 29
30065351
FIGURE 29. START and STOP Conditions
www.national.com
32
Resistor
RID kΩ
Address
7'b
Address
8'b
0 appended
(WRITE)
0.47
7b' 111 0001 (h'71)
8b' 1110 0010 (h'E2)
2.7
7b' 111 0010 (h'72)
8b' 1110 0100 (h'E4)
8.2
7b' 111 0011 (h'73)
8b' 1110 0110 (h'E6)
Open
7b' 111 0110 (h'76)
8b' 1110 1100 (h'EC)
DS92LV2411/DS92LV2412
30065338
FIGURE 30. Serial Control Bus — READ
30065339
FIGURE 31. Serial Control Bus — WRITE
TABLE 12. SERIALIZER — Serial Bus Control Registers
ADD ADD Register Name
(dec) (hex)
0
1
2
0
1
2
Ser Config 1
Device ID
De-Emphasis
Control
Bit(s)
R/W
Defa Function
ult
(bin)
7
R/W
0
Reserved
Reserved
6
R/W
0
Reserved
Reserved
5
R/W
0
RFB
0: Data latched on Falling edge of CLKIN
1: Data latched on Rising edge of CLKIN
4
R/W
0
VODSEL
0: Low
1: High
3:2
R/W
00
CONFIG
00: Control Signal Filter Disabled
01: Control Signal Filter Enabled
10: Reserved
11: Reserved
1
R/W
0
SLEEP
Note – not the same function as PowerDown (PDB)
0: normal mode
1: Sleep Mode – Register settings retained.
0
R/W
0
REG
0: Configurations set from control pins
1: Configuration set from registers (except I2C_ID)
7
R/W
0
REG ID
0: Address from ID[X] Pin
1: Address from Register
6:0
R/W
1101 ID[X]
000
Serial Bus Device ID, Four IDs are:
7b '1101 001 (h'69)
7b '1101 010 (h'6A)
7b '1101 011 (h'6B)
7b '1101 110 (h'6E)
All other addresses are Reserved.
7:5
R/W
000
De-E Setting
000: set by external Resistor
001: -1 dB
010: -2 dB
011: -3.3 dB
100: -5 dB
101: -6.7 dB
110: -9 dB
111: -12 dB
4
R/W
0
De-E EN
0: De-Emphasis Enabled
1: De-Emphasis Disabled
3:0
R/W
000
Reserved
Reserved
33
Description
www.national.com
DS92LV2411/DS92LV2412
TABLE 13. DESERIALIZER — Serial Bus Control Registers
ADD ADD Register Name
(dec) (hex)
0
1
2
0
1
2
www.national.com
Des Config 1
Slave ID
Des Features 1
Bit(s)
R/W
Defa Function
ult
(bin)
Description
7
R/W
0
LF_MODE
0: 20 to 50 MHz SSCG Operation
1: 5 to 20 MHz SSCG Operation
6
R/W
0
OS_CLKOUT
0: Normal CLKOUT Slew Rate
1: Increased CLKOUT Slew Rate
5
R/W
0
OS_DATA
0: Normal DATA Slew Rate
1: Increased DATA Slew Rate
4
R/W
0
RFB
0: Data strobed on Falling edge of CLKOUT
1: Data strobed on Rising edge of CLKOUT
3:2
R/W
00
CONFIG
00: Normal Mode, Control Signal Filter Disabled
01: Normal Mode, Control Signal Filter Enabled
10: Reserved
11: Reserved
1
R/W
0
SLEEP
Note – not the same function as PowerDown (PDB)
0: Normal Mode
1: Sleep Mode – Register settings retained.
0
R/W
0
REG Control
0: Configurations set from control pins / STRAP pins
1: Configurations set from registers (except I2C_ID)
7
R/W
0
6:0
R/W
7
R/W
0
OP_LOW
0: Set outputs state LOW (except LOCK)
1: Release output LOW state, outputs toggling
normally
Note: This register only workds during LOCK = 1
6
R/W
0
OSS_SEL
Output Sleep State Select
0: CLKOUT, DO[23:0], CO1, CO2, CO3 = Tri-State,
LOCK = Normal, PASS = H
1: CLKOUT, DO[23:0], CO1, CO2, CO3 = L, LOCK =
Normal, PASS = H
5:4
R/W
00
Reserved
Reserved
3
R/W
0
OP_LOW Strap
Bypass
0: Strap will determine whether OP_LOW feature is
ON or OFF
1: Turns OFF OP_LOW feature
2:0
R/W
00
OSC_SEL
000: disable
001: 50 MHz ±40%
010: 25 MHz ±40%
011: 16.7 MHz ±40%
100: 12.5 MHz ±40%
101: 10 MHz ±40%
110: 8.3 MHz ±40%
111: 6.3 MHz ±40%
0: Address from ID[X] Pin
1: Address from Register
1110 ID[X]
000
Serial Bus Device ID, Four IDs are:
7b '1110 001 (h'71)
7b '1110 010 (h'72)
7b '1110 011 (h'73)
7b '1110 110 (h'76)
All other addresses are Reserved.
34
3
4
3
4
Des Features 2
ROUT Config
Bit(s)
R/W
Defa Function
ult
(bin)
Description
7:5
R/W
000
EQ Gain
000: ~1.625 dB
001: ~3.25 dB
010: ~4.87 dB
011: ~6.5 dB
100: ~8.125 dB
101: ~9.75 dB
110: ~11.375 dB
111: ~13 dB
4
R/W
0
EQ Enable
0: EQ = disable
1: EQ = enable
3:0
R/W
7
R/W
6:0
R/W
0000 SSC
0
DS92LV2411/DS92LV2412
ADD ADD Register Name
(dec) (hex)
IF LF_MODE = 0, then:
000: SSCG disable
0001: fdev = ±0.5%, fmod = CLK/2168
0010: fdev = ±1.0%, fmod = CLK/2168
0011: fdev = ±1.5%, fmod = CLK/2168
0100: fdev = ±2.0%, fmod = CLK/2168
0101: fdev = ±0.5%, fmod = CLK/1300
0110: fdev = ±1.0%, fmod = CLK/1300
0111: fdev = ±1.5%, fmod = CLK/1300
1000: fdev = ±2.0%, fmod = CLK/1300
1001: fdev = ±0.5%, fmod = CLK/868
1010: fdev = ±1.0%, fmod = CLK/868
1011: fdev = ±1.5%, fmod = CLK/868
1100: fdev = ±2.0%, fmod = CLK/868
1101: fdev = ±0.5%, fmod = CLK/650
1110: fdev = ±1.0%, fmod = CLK/650
1111: fdev = ±1.5%, fmod = CLK/650
IF LF_MODE = 1, then:
000: SSCG disable
0001: fdev = ±0.5%, fmod = CLK/620
0010: fdev = ±1.0%, fmod = CLK/620
0011: fdev = ±1.5%, fmod = CLK/620
0100: fdev = ±2.0%, fmod = CLK/620
0101: fdev = ±0.5%, fmod = CLK/370
0110: fdev = ±1.0%, fmod = CLK/370
0111: fdev = ±1.5%, fmod = CLK/370
1000: fdev = ±2.0%, fmod = CLK/370
1001: fdev = ±0.5%, fmod = CLK/258
1010: fdev = ±1.0%, fmod = CLK/258
1011: fdev = ±1.5%, fmod = CLK/258
1100: fdev = ±2.0%, fmod = CLK/258
1101: fdev = ±0.5%, fmod = CLK/192
1110: fdev = ±1.0%, fmod = CLK/192
1111: fdev = ±1.5%, fmod = CLK/192
Repeater Enable 0: Output ROUT+/- = disable
1: Output ROUT+/- = enable
0000 Reserved
000
35
Reserved
www.national.com
DS92LV2411/DS92LV2412
TYPICAL APPLICATION CONNECTION
Figure 32 shows a typical connection diagram of the
DS92LV2411 Ser in pin control mode for a 24-bit application.
The CML outputs require 0.1 µF AC coupling capacitors to the
line. The line driver includes internal termination. Bypass capacitors are placed near the power supply pins. At a minimum,
four 0.1 µF capacitors and a 4.7 µF capacitor should be used
for local device bypassing. System GPO (General Purpose
Output) signals control the PDB and BISTEN pins. In this application the RFB pin is tied Low to latch data on the falling
edge of the CLKIN. In this example the cable is long, therefore
the VODSEL pin is tied High and a De-Emphasis value is selected by the resistor R1. The interface to the host is with 1.8
V LVCMOS levels, thus the VDDIO pin is connected also to
the 1.8V rail. The optional Serial Bus control is not used in this
example, thus the SCL, SDA and ID[x] pins are left open. A
delay cap is placed on the PDB signal to delay the enabling
of the device until power is stable.
Applications Information
DISPLAY APPLICATION
The DS92LV2411/DS92LV2412 chipset is intended for interface between a host (graphics processor) and a Display. It
supports an 24-bit color depth (RGB888). In a RGB888 application, 24 color bits (D[23:0), Pixel Clock (CLKIN) and three
control bits (C1, C2, C3) are supported across the serial link
with CLK rates from 5 to 50 MHz. The chipset may also be
used in 18-bit color applications. In this application three to
six general purpose signals may also be sent from host to
display.
The Des is expected to be located close to its target device.
The interconnect between the Des and the target device is
typically in the 1 to 3 inch separation range. The input capacitance of the target device is expected to be in the 5 to 10 pF
range. Care should be taken on the CLK output trace as this
signal is edge sensitive and strobes the data. It is also assumed that the fanout of the Des is one. If additional loads
need to be driven, a logic buffer or mux device is recommended.
30065344
FIGURE 32. DS92LV2411 Typical Connection Diagram — Pin Control
www.national.com
36
STRAP pull-up on DO23. The receiver input equalizer is also
enabled and set to provide 7.5 dB of gain, this is accomplished
with EQ[3:0] set to 1001'b with STRAP pull ups on DO12 and
DO15. To reduce parallel bus EMI, the SSCG feature is enabled and set to fmod = CLK/2168 and ±1% with SSC[3:0] set
to 0010'b and a STRAP pull-up on DO4. The desired features
are set with the use of the four pull up resistors.
The interface to the target display is with 3.3V LVCMOS levels, thus the VDDIO pin is connected to the 3.3 V rail. The
optional Serial Bus Control is not used in this example, thus
the SCL, SDA and ID[x] pins are left open. A delay cap is
placed on the PDB signal to delay the enabling of the device
until power is stable.
30065345
FIGURE 33. DS92LV2412 Typical Connection Diagram — Pin Control
37
www.national.com
DS92LV2411/DS92LV2412
Figure 33 shows a typical connection diagram of the
DS92LV2412 Des in pin/strap control mode for a 24-bit application. The CML inputs utilize 0.1 µF coupling capacitors to
the line and the receiver provides internal termination. Bypass
capacitors are placed near the power supply pins. At a minimum, seven 0.1 µF capacitors and two 4.7 µF capacitors
should be used for local device bypassing. System GPO
(General Purpose Output) signals control the PDB and the
BISTEN pins. In this application the RFB pin is tied Low to
strobe the data on the falling edge of the CLKOUT.
Since the device in the Pin/STRAP mode, four 10 kΩ pull up
resistors are used on the parallel output bus to select the desired device features. CFEN is set to 1 for Normal Mode with
Control Signal Filter enabled, this is accomplished with the
DS92LV2411/DS92LV2412
quency switching noise. It is recommended to connect power
and ground pins directly to the power and ground planes with
bypass capacitors connected to the plane with via on both
ends of the capacitor. Connecting power or ground pins to an
external bypass capacitor will increase the inductance of the
path.
A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces
the parasitic inductance of the capacitor. The user must pay
attention to the resonance frequency of these external bypass
capacitors, usually in the range of 20-30 MHz. To provide effective bypassing, multiple capacitors are often used to
achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common
practice to use two vias from power and ground pins to the
planes, reducing the impedance at high frequency.
Some devices provide separate power and ground pins for
different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit.
Separate planes on the PCB are typically not required. Pin
Description tables typically provide guidance on which circuit
blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to
sensitive circuits such as PLLs.
Use at least a four layer board with a power and ground plane.
Locate LVCMOS signals away from the CML lines to prevent
coupling from the LVCMOS lines to the CML lines. Closelycoupled differential lines of 100 Ohms are typically recommended for differential interconnect. The closely coupled
lines help to ensure that coupled noise will appear as common-mode and thus is rejected by the receivers. The tightly
coupled lines will also radiate less.
Information on the LLP style package is provided in National
Application Note: AN-1187.
Power Up Requirements and PDB Pin
The VDD (VDDn and VDDIO) supply ramp should be faster than
1.5 ms with a monotonic rise. If slower then 1.5 ms then a
capacitor on the PDB pin is needed to ensure PDB arrives
after all the VDD have settled to the recommended operating
voltage. When PDB pin is pulled to VDDIO, it is recommended
to use a 10 kΩ pull-up and a 22 uF cap to GND to delay the
PDB input signal.
TRANSMISSION MEDIA
The Ser/Des chip set is intended to be used in a point-to-point
configuration, through a PCB trace, through twisted pair cable
or through 50Ω coaxial cables. The Ser and Des provide internal terminations providing a clean signaling environment.
The interconnect for the differential serial interface should
present a differential impedance of 100Ω. Use cables and
connectors that have matched differential impedance to minimize impedance discontinuities. Shielded or un-shielded cables may be used depending upon the noise environment and
application requirements.
For 50Ω coaxial cable serial interfaces, any unused input or
output pin must be terminated with an 0.1 µF AC coupling
capacitor and a 50Ω resistor to ground. The PCB traces and
serial interconnect should have a single ended impedance of
50Ω.
LIVE LINK INSERTION
The Ser and Des devices support live pluggable applications.
The automatic receiver lock to random data “plug & go” hot
insertion capability allows the DS92LV2412 to attain lock to
the active data stream during a live insertion event.
PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS
Circuit board layout and stack-up for the Ser/Des devices
should be designed to provide low-noise power feed to the
device. Good layout practice will also separate high frequency
or high-level inputs and outputs to minimize unwanted stray
noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2
to 4 mils) for power / ground sandwiches. This arrangement
provides plane capacitance for the PCB power system with
low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement
of external bypass capacitors less critical. External bypass
capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of
0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF
to 10 uF range. Voltage rating of the tantalum capacitors
should be at least 5X the power supply voltage being used.
Surface mount capacitors are recommended due to their
smaller parasitics. When using multiple capacitors per supply
pin, locate the smaller value closer to the pin. A large bulk
capacitor is recommend at the point of power entry. This is
typically in the 50uF to 100uF range and will smooth low fre-
www.national.com
SERIAL INTERCONNECT GUIDELINES
See AN-1108 and AN-905 for full details.
• Use 100Ω coupled differential pairs
• Use the S/2S/3S rule in spacings
– S = space between the pair
– 2S = space between pairs
– 3S = space to LVCMOS signal
• Minimize the number of Vias
• Use differential connectors when operating above
500Mbps line speed
• Maintain balance of the traces
• Minimize skew within the pair
• Terminate as close to the TX outputs and RX inputs as
possible
Additional general guidance can be found in the LVDS
Owner’s Manual - available in PDF format from the National
web site at: www.national.com/lvds
38
DS92LV2411/DS92LV2412
Physical Dimensions inches (millimeters) unless otherwise noted
48–pin LLP Package (7.0 mm x 7.0 mm x 0.8 mm, 0.5 mm pitch)
NS Package Number SQA48A
60–pin LLP Package (9.0 mm x 9.0 mm x 0.8 mm, 0.5 mm pitch)
NS Package Number SQA60B
39
www.national.com
DS92LV2411/DS92LV2412 5-50MHz 24-Bit Channel Link II Serializer and Deserializer
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]