NAIS DSBT2-S-DC3V 4,000 v breakdown voltage ds relay Datasheet

TESTING
DS-BT
RELAYS
4,000 V BREAKDOWN
VOLTAGE DS RELAYS
FEATURES
20.65
.813
10.65
.419
•4,000 V breakdown voltage
•Reinforced insulation between coil and contacts
•Surge voltage withstand: 1500 V FCC Parts 68
10.5
.413
mm inch
SPECIFICATIONS
Contact
Characteristics
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Contact material
Nominal switching capacity
Max.
switching power
Rating
(resistive Max. switching voltage
load)
Max. switching current
Min. switching capacity**1
Electrical
life (min.
ope.)
Mechanical (at 180 cpm)
2 Form C
2 Form D
50 mΩ
Gold-clad silver
2 A 30 V DC
1 A 30 V DC
60 W, 125 VA 30 W, 62.5 VA
220 V DC, 250 V AC
2A
1A
10 µA 10 mV DC
2×107
106
2×105
Electrical (at 20 cpm)
**1 This value can change due to the switching frequency, environmental
conditions, and desired reliability level, therefore it is recommended to
check this with the actual load.
Coil
Arrangement
Nominal operating power
2 Form C
360 mW
2 Form D
540 mW
Remarks
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as "Initial breakdown voltage" section
*2 Detection current: 10mA
*3 Excluding contact bounce time
*4 Half-wave pulse of sine wave: 11ms, detection time: 10µs
*5 Half-wave pulse of sine wave: 6ms
*6 Detection time: 10µs
*7 Refer to 5. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT (Page 61)
TYPICAL APPLICATIONS
Modem
Facsimile
Telecommunication equipment
Arrangement
Max. operating speed
Initial insulation resistance*1
Initial
breakdown
voltage*2
2 Form C
2 Form D
60 cpm at rated load
Between open contacts
Between contacts and coil
Between contacts sets
FCC surge voltage between open
contacts
Operate time*3 (at nominal voltage)
Release time (without diode)*3
(at nominal voltage)
Temperature rise
Functional*4
Vibration
resistance
Destruction*5
Functional*6
Destruction
Conditions for oper- Ambient
ation, transport and temp.
storage*7
(Not freezing and
Humidity
condensing at low
temperature)
Unit weight
Shock
resistance
Min. 100 MΩ (at 500 V DC)
750 Vrms
500 Vrms
for 1 min.
for 1 min.
4,000 Vrms for 1 min.
750 V
500 V
1,500 V
Approx. 3 ms
Approx. 2 ms
Max. 65°C
10 to 55 Hz
at double amplitude of 3.3 mm
10 to 55 Hz
at double amplitude of 5 mm
Min. 294 m/s2 (30 G)
Min. 980 m/s2 (100 G)
–40°C to +70°C
–40°C to +60°C
–40°F to +158°F –40°F to +140°F
5 to 85%R.H.
Approx. 4.0 g 0.14 oz
ORDERING INFORMATION
DSBT
Contact
arrangement
2
M
Sensitivity
2D
DC3V
MBB function
S: 360 mW
Nil: BBM (Form C)
(2 Form C only)
2D: 2MBB
M: 540 mW
(2 Form D)
(2 Form D only)
Note: Standard packing; Carton: 25 pcs. Case 1,000 pcs.
2: 2 Form C or
2 Form D
192
Coil voltage
DC 1.5, 3, 5,
6, 9, 12, 24 V
DS-BT
TYPES AND COIL DATA (at 20°C 68°F)
1) 2 Form C type
Operating
function
Coil voltage,
V DC
Part No.
DSBT2-S-DC1.5V
DSBT2-S-DC3V
DSBT2-S-DC5V
Single side
DSBT2-S-DC6V
stable
DSBT2-S-DC9V
DSBT2-S-DC12V
DSBT2-S-DC24V
1.5
3
5
6
9
12
24
Pick-up
voltage,
V DC (max.)
1.125
2.25
3.75
4.5
6.75
9
18
Drop-out
voltage,
V DC (min.)
0.15
0.3
0.5
0.6
0.9
1.2
2.4
Nominal operating
current,
mA (±10%)
240
120
72
60
40
30
15
Coil
resistance,
Ω (±10%)
6.25
25
69.4
100
225
400
1,600
Nominal
operating
power, mW
Pick-up
voltage,
V DC (max.)
1.125
2.25
3.75
4.5
6.75
9
18
Drop-out
voltage,
V DC (min.)
0.15
0.3
0.5
0.6
0.9
1.2
2.4
Nominal operating
current,
mA (±10%)
360
180
108
90
60
45
22.5
Coil
resistance,
Ω (±10%)
4.2
16.7
46.3
66.7
150
266.7
1,066.7
Nominal
operating
power, mW
360
Max. allowable
voltage, V DC
(at 50°C 122°F)
1.95
3.9
6.5
7.8
11.7
15.6
31.2
2) 2 Form D type
Operating
function
Coil voltage,
V DC
Part No.
DSBT2-M-2D-DC1.5V
DSBT2-M-2D-DC3V
DSBT2-M-2D-DC5V
Single side
DSBT2-M-2D-DC6V
stable
DSBT2-M-2D-DC9V
DSBT2-M-2D-DC12V
DSBT2-M-2D-DC24V
1.5
3
5
6
9
12
24
540
Max. allowable
voltage, V DC
(at 50°C 122°F)
1.8
3.6
6
7.2
10.8
14.4
28.8
Note: Standard packing Tube: 25 pcs. Case: 1,000 pcs.
DIMENSIONS
mm inch
PC board pattern (Bottom view)
10.65
.419
20.65
.813
8-0.9 dia.
8-.035 dia.
10.50
.413
9.9
.390
0.30
.012
7.62
.300
0.6
.024
3.4
.134
0.3
.012
5.08
.200
5.08
.200
7.62
.300
0.6
.024
2
.079
5.6
.220
7.82
.308
7.62
.300
7.82
.308
5.08 5.08
.200 .200
0.35
.014
7.62
.300
Tolerance: ±0.1 ± .004
Schematic (Bottom view)
9 11 13
16
N.O. N.C. COM –
General tolerance: ±0.3 ± .012
N.O. N.C. COM +
8 6 4
1
REFERENCE DATA
Change of pick-up and drop-out voltage
4
Pick-up voltage
3
Max.
–
x
Min.
Drop-out voltage
2
Max.
–
x
1
0
Change of contact resistance
Contact resistance, mΩ
Tested sample: DSBT2-S-DC5V, 10 pcs.
Coil applied voltage: 5 V DC
Operating frequency: 30 cpm
Pick-up/drop-out voltage, V DC
1. Mechanical life test
N.C. contact
N.O. contact
100
Max.
Max.
–
x
–
x
Min.
Min.
10
Min.
0
10
100
1000
No. of operations, × 104
0
0
10
100
1000
No. of operations, × 104
193
DS-BT
2. Electrical life test (resistive)
N.O.:
No.11–13
N.C.:
No. 4–6
30 V DC
Pick-up voltage
Max.
–
x
Min.
6
5
4
3
Drop-out voltage
Contact resistance, mΩ
Circuit
100
7
Pick-up/drop-out voltage, V DC
Tested sample: DSBT2-S-DC12V, 6 pcs.
Condition: 2 A 30 V DC resistive load, 30 cpm
Max.
–
x
Min.
2
N.C. contact
N.O. contact
Max.
–
x
Max.
–
x
Min.
Min.
10
1
0
5
0
10
15
20
No. of operations, × 104
3. Coil temperature rise
4. Operate and release time characteristics
Tested sample: DSBT2-S-DC12V, 5 pcs.
Measured portion: Inside the coil
Tested sample: DSBT2-S-DC5V, 10 pcs.
Ambient temperature: 23°C 73°F
Coil
70
6
N.O. contact
2A
1A
0A
60
T1
Coil
T1: Operate time
T2: Operate bounce
time
N.C. contact
40
T3
30
T4
3
0
Without diode (T3)
Release time, ms
Measured terminals: 9-13
5
4
3
2
0.5
Measured terminals: 4-8
80
100
120
Coil applied voltage, %V
Without diode (T4)
6
0
4
1
400
600
800
Coil power, mW
1.5
1.0
5
2
T3: Release time
T4: Release bounce
time
Release bounce time, ms
200
Without diode (T2)
Operate bounce time, ms
T2
50
0
10
15
20
No. of operations, × 104
Without diode (T1)
Operate time, ms
Coil temperature rise, °C
80
5
1.5
Measured terminals: 4-6
1.0
0.5
Measured terminals: 11-13
1
0
80
100
120
Coil applied voltage, %V
80
100
120
Coil applied voltage, %V
0
80
100
120
Coil applied voltage, %V
5. Distribution of pick-up and drop-out voltage
6. Distribution of breakdown voltage
Tested sample: DSBT2-S-DC5V, 50 pcs.
Pick-up voltage
(between contacts and coil)
Tested sample: DSBT2-S-DC5V, 100 pcs.
Drop-out voltage
10
20
Mean: AC 5169 V
Max.: AC 5800 V
Min.: AC 4700 V
30
Quantity
20
40
Specified value: More than 0.50 V DC
–– 1.65 V DC
Mean value (x):
Max.: 2.23 V DC
Min.: 0.78 V DC
Quantity
Quantity
Specified value: Less than 3.75 V DC
– 3.22 V DC
Mean value (x):
Max.: 3.69 V DC
Min.: 2.65 V DC
20
10
10
2.0
2.5
3.0
3.5
4.0
4.5
Pick-up voltage, V
5.0
0
0.5
1.0
1.5
2.0
2.5
Drop-out voltage, V
3.0
0
AC 4000
AC 5000
AC 6000
Breakdown voltage, V AC
For Cautions for Use, see Relay Technical Information
194
9/1/2000
All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Similar pages