FTDI DS FT311D The ft311d is a full speed usb host specifically targeted at providing access to peripheral hardware from an android platform with a usb device port. Datasheet

DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Future Technology Devices
International Ltd.
FT311D
(USB Android Host IC)
The FT311D is a Full Speed USB host
specifically targeted at providing
access to peripheral hardware from an
Android platform with a USB device
port. The device will bridge the USB
port to six user selectable interface
types and has the following advanced
features:

Interface options selectable via 3 mode select
pins.
Suitable for use on any Android platform
supporting Android Open Accessory Mode
(Typically
3.1
onwards,
however
some
platforms may port Open Accessory Mode to
version 2.3.4)

12MHz oscillator using external crystal.

7 GPIO lines interface option

Integrated power-on-reset circuit.

Basic UART interface with RXD, TXD, RTS, CTS
pins option.

+3V3 Single Supply Operation with 5V tolerant
inputs.

TX_ACTIVE signal for controlling transceivers
on RS485 interfaces.

USB 2.0 Full Speed compatible.

4 PWM channels option.

Extended operating temperature range; -40⁰C
to 85⁰C.

I2C master interface option.


SPI Slave interface option supporting modes 0,
1, 2 and 3 with MSB/LSB options
Available in compact Pb-free 32 Pin LQFP and
QFN packages (both RoHS compliant).

SPI Master interface option supporting modes
0, 1, 2 and 3 with MSB/LSB options.

USB error indicator pin

Single chip USB to selectable interface.

Entire USB protocol handled on the chip. No
USB specific firmware programming required.

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced
in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology
Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your
statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary
information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by
the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow
G41 1HH United Kingdom. Scotland Registered Company Number: SC136640
Copyright © 2012 Future Technology Devices International Limited
1
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
1
Typical Applications

Connecting Android phones to USB accessories

Home automation via Android devices

Connecting Android tablets to USB accessories

Data logging from USB accessories

Controlling instrumentation from Android
devices.

Connecting serial printing devices to Android
devices
1.1 Part Numbers
Part Number
Package
FT311D-32Q1C-x
32 Pin QFN
FT311D-32L1C-x
32 Pin LQFP
Note: Packing codes for x is:
- R: Taped and Reel, QFN 3,000pcs per reel, LQFP 1500 pcs per reel.
- (no suffix): Tray packing, 260pcs per tray QFN, 250 pcs per tray LQFP
For example: FT311D-32Q1C-R is 3,000pcs QFN taped and reel packing
1.2 USB Compliant
At the time of writing this datasheet, the FT311D was still to complete USB compliancy testing.
Copyright © 2012 Future Technology Devices International Limited
2
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
2
FT311D Block Diagram
UART
PWMs
USB Host
USBDM
SPI Master
SPI Slave
Input / Output Multiplexer
USB
Transceiver
Peripheral Bus
USBDP
GPIOS
I2C MASTER
CNFG0
CNFG1
CNFG2
Figure 2.1 FT311D Block Diagram
For a description of each function please refer to Section 4.
Copyright © 2012 Future Technology Devices International Limited
3
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Table of Contents
1
Typical Applications ...................................................................... 2
1.1
Part Numbers...................................................................................... 2
1.2
USB Compliant .................................................................................... 2
2
FT311D Block Diagram ................................................................. 3
3
Device Pin Out and Signal Description .......................................... 6
3.1
Package Symbol.................................................................................. 6
3.1.1
3.2
Interface Selection ............................................................................. 8
3.2.1
4
Package PinOut Description ........................................................................................... 6
Interface pinout ........................................................................................................... 8
Function Description................................................................... 10
4.1
Key Features ..................................................................................... 10
4.2
Functional Block Descriptions ........................................................... 10
4.2.1
Peripheral Interface Modules ....................................................................................... 10
4.2.2
USB Transceivers ....................................................................................................... 10
4.2.3
USB Host .................................................................................................................. 10
4.3
I/O Peripherals Signal Names .......................................................... 10
4.4
Default Mode Strings ........................................................................ 11
5
Peripheral Interfaces ................................................................. 12
5.1
General Purpose Input Output .......................................................... 12
5.2
UART Interface ................................................................................. 12
5.2.1
UART Mode Signal Descriptions ................................................................................... 13
5.3
Pulse Width Modulation .................................................................... 13
5.4
I2C.................................................................................................... 13
5.5
Serial Peripheral Interface – SPI Modes ........................................... 14
5.5.1
SPI Clock Phase Modes ............................................................................................... 14
5.5.2
Serial Peripheral Interface – Slave ............................................................................... 16
5.5.3
Serial Peripheral Interface – SPI Master ........................................................................ 16
6
USB Error Detection.................................................................... 19
7
Absolute Maximum Ratings ........................................................ 20
7.1
DC Characteristics............................................................................. 20
7.2
ESD and Latch-up Specifications ....................................................... 22
8
Application Examples ................................................................. 23
8.1
USB to GPIO Converter ..................................................................... 23
8.2
USB to UART Converter ..................................................................... 24
8.3
USB to PWM Converter ..................................................................... 25
8.4
USB to I2C (Master) Converter .......................................................... 26
Copyright © 2012 Future Technology Devices International Limited
4
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.5
USB to SPI (Slave) Converter ........................................................... 27
8.6
USB to SPI (Master) Converter ......................................................... 28
9
Package Parameters ................................................................... 29
9.1
FT311D Package Markings ............................................................... 29
9.1.1
QFN-32 .................................................................................................................... 29
9.1.2
LQFP-32 ................................................................................................................... 30
9.2
9.2.1
QFN-32 Package Dimensions ....................................................................................... 31
9.2.2
LQFP-32 Package Dimensions ...................................................................................... 32
9.3
10
FT311D Package Dimensions ............................................................ 31
Solder Reflow Profile ........................................................................ 33
Contact Information ................................................................... 35
Appendix A – References ........................................................................... 36
Useful utilities and examples firmware...................................................... 36
Appendix B - List of Figures and Tables ..................................................... 37
Appendix C - Revision History .................................................................... 39
Copyright © 2012 Future Technology Devices International Limited
5
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
3
Device Pin Out and Signal Description
3.1 Package Symbol
Figure 3.1 QFN Schematic Symbol
Note the pinout is the same for the QFN and LQFP packages.
3.1.1 Package PinOut Description
Note: # denotes an active low signal.
Pin No.
Name
Type
2
3.3V
VREGIN
POWER
Input
3
1.8V VCC
PLL IN
POWER
13, 22, 28
VCCIO
7
VREGOUT
1,6,16,19,27
GND
Input
POWER
Input
POWER
Output
POWER
Input
Description
3V3 supply to IC internal 1V8 regulator
1V8 supply to IC core
3V3 supply for the IO cells
1V8 output. May be used as input source for pin 3.
0V Ground input.
Table 3.1 Power and Ground
Copyright © 2012 Future Technology Devices International Limited
6
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Pin No.
Name
Type
17
USBDP
INPUT/OUTPUT
USB Data Signal Plus.
18
USBDM
INPUT/OUTPUT
USB Data Signal Minus.
4
XTIN
INPUT
5
XTOUT
OUTPUT
8
TEST1
INPUT
For internal use. Pull to GND
9
TEST2
INPUT
For factory use. Pull to 3V3.
10
RESET#
INPUT
Reset input (active low).
20, 21
NC
-
11
TEST0
OUTPUT
12
CNFG0
14
CNFG1
Description
Input to 12MHz Oscillator Cell. Connect 12MHz
crystal across pins 4 and 5.
Output from 12MHz Oscillator Cell. Connect 12MHz
crystal across pins 4 and 5.
No connect pins. Leave unterminated.
Active low signal that may be used to control a
switch for enabling power to the USB port pin 1
(VBUS).
INPUT
Configuration pin 0 used to select between
GPIO,UART,PWM,I2C and SPI.
Pull to Ground = Logic „0‟(No external resistor
needed)
Leave Open = Logic „1‟ (Internal Pull up is present)
INPUT
Configuration pin 1 used to select between
GPIO,UART,PWM,I2C and SPI.
Pull to Ground = Logic „0‟(No external resistor
needed)
Leave Open = Logic „1‟ (Internal Pull up is present)
Configuration pin 2 used to select between
GPIO,UART,PWM,I2C and SPI.
Pull to Ground = Logic „0‟(No external resistor
needed)
Leave Open = Logic „1‟ (Internal Pull up is present)
15
CNFG2
INPUT
32
USB_ERROR#
OUTPUT
Output signal to indicate a problem with the USB
connection
Table 3.2 Common Function pins
Pin
No.
Name
Type
23
IOBUS0
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
24
IOBUS1
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
25
IOBUS2
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
26
IOBUS3
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
Description
Copyright © 2012 Future Technology Devices International Limited
7
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
29
IOBUS4
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
30
IOBUS5
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
31
IOBUS6
INPUT/OUTPUT
I/O signal. Function depends on CNFG pin setting. See table 3.4
Table 3.3 Interface Pins
Notes:
1. When used in Input Mode, the input pins are pulled to VCCIO via internal 75kΩ (approx.) resistors.
3.2 Interface Selection
The FT311D has multiple interfaces available for connecting to external devices. The resources available
are GPIO, UART, PWM, I2C(Master), SPI(Slave) and SPI(Master). The selection of what interface the user
requires is configured using the CNFG0, CNFG1 and CNFG2 input pins as per table 3.4.
CNFG2
CNFG1
CNFG0
Mode
GND
GND
GND
GPIO
GND
GND
Leave
Open
UART
GND
Leave
Open
GND
PWM
GND
Leave
Open
Leave
Open
I2C (Master)
Leave
Open
GND
GND
SPI (Slave)
Leave
Open
GND
Leave
Open
SPI (Master)
Table 3.4 CBUS Configuration Control
Note 1: When left open the pin is a logic 1.
Note 2: Mode “110” is a factory test mode and should not be used.
Note 3: Mode “111” will default to GPIO mode.
3.2.1 Interface pinout
The actual pinout for each interface type is detailed in table 3.5
Pin No
Pin
Name
GPIO
UART
PWM
I2C
(Master)
SPI
(Slave)
SPI
(Master)
23
IOBUS0
GPIO0
UART_TXD
PWM0
I2C_CLK
-
-
24
IOBUS1
GPIO1
UART_RXD
PWM1
I2C_DATA
-
-
25
IOBUS2
GPIO2
UART_RTS
#
PWM2
-
-
-
26
IOBUS3
GPIO3
UART_CTS
#
PWM3
-
SPI_S_SS0
SPI_M_SS0
Copyright © 2012 Future Technology Devices International Limited
8
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Pin No
Pin
Name
GPIO
29
IOBUS4
GPIO4
30
IOBUS5
GPIO5
31
IOBUS6
GPIO6
PWM
I2C
(Master)
SPI
(Slave)
SPI
(Master)
-
-
SPI_S_CLK
SPI_M_CLK
-
-
-
SPI_S_MOSI
SPI_M_MOSI
-
-
-
SPI_S_MISO
SPI_M_MISO
UART
UART_TX
_ACTIVE
Table 3.5 I/O Configuration
Copyright © 2012 Future Technology Devices International Limited
9
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
4
Function Description
FT311D is FTDIs Android Accessory Mode integrated circuit device or Android Host. The FT311D behaves
like a bridge between an Android device and the various I/O available. Selection of various modes is
performed using CNFGx pins.
4.1 Key Features
Easy to use Android accessory IC translating the Device port of the android tablet into either GPIO, UART,
PWM, I2C Master, SPI Slave or SPI Master capabilities
4.2 Functional Block Descriptions
The following paragraphs describe each function within FT311D. Please refer to the block diagram shown
in Figure 2.1.
4.2.1 Peripheral Interface Modules
FT311D has six peripheral interface modules available for selection. Full descriptions of each module are
described in Section 5.

GPIO - General purpose I/O pins

UART

PWM

I2C Master

SPI Slave

SPI Master
4.2.2 USB Transceivers
USB transceiver cells provide the physical USB device interface supporting USB 1.1 and USB 2.0
standards. Low-speed and full-speed USB data rates are supported. The output driver provides +3.3V
level slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB
DATA IN, SE0 and USB Reset condition detection. These cells also include integrated internal pull-down
resistors as required for host mode.
4.2.3 USB Host
These blocks handle the parallel-to-serial and serial-to-parallel conversion of the USB physical layer. This
includes bit stuffing, CRC generation.
4.3 I/O Peripherals Signal Names
Peripheral
Signal Name
Outputs
Inputs
Description
GPIO
gpio
7
7
General purpose I/O
Transmit asynchronous data output
UART
PWM
I2C
SPI Slave
uart_txd
1
0
uart_rts#
1
0
Request to send control output
uart_rxd
0
1
Receive asynchronous data input
uart_cts#
0
1
Clear to send control input
uart_tx_active
0
1
UART active signal (typically used with RS485)
pwm
4
0
Pulse width modulation
I2c_scl
0
1
I2C bus serial clock line - slave
I2c_sda
1
1
I2C bus serial data line - slave
spi_s_clk
0
1
SPI clock input
Copyright © 2012 Future Technology Devices International Limited
10
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
SPI
Master
spi_s_ss#
0
1
SPI slave select input
spi_s_mosi
1
1
SPI master out serial in
spi_s_miso
1
0
SPI master in slave out
spi_m_clk
1
0
SPI clock input – master
spi_m_mosi
1
1
Master out slave in - master
spi_m_miso
0
1
Master in slave out - master
spi_m_ss_0#
1
0
Active low slave select 0 from master to slave 0
Table 4.1 I/O Peripherals Signal Names
Note: # is used to indicate an active low signal.
4.4 Default Mode Strings
When the USB port is connected to the Android USB port, the Android platform will determine which
application to load based on the strings read from the FT311D. These strings are configurable with a
Windows utility: FT311Cofiguration.exe available for download from the FTDI website at:
http://www.ftdichip.com/Android/FT311Configuration.zip
Default values for the strings are set in the device as per Table 4.2
Descriptor String
Default Value
Manufacturer
FTDI
Model (depends on GPIO Mode selection):
GPIO
FTDIGPIODemo
UART
FTDIUARTDemo
PWM
FTDIPWMDemo
I2C
FTDII2CDemo
SPI Slave
FTDISPISlaveDemo
SPI Master
FTDISPIMasterDemo
Version
1.0
Serial
VinculumAccessory1
Description URL
http://www.ftdichip.com
Table 4.2 Default Descriptor Strings
Copyright © 2012 Future Technology Devices International Limited
11
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
5
Peripheral Interfaces
In addition to the USB Host, FT311D contains the following peripheral interfaces:

General Purpose Input Output (GPIO)

Universal Asynchronous Receiver Transmitter (UART)

Four Pulse Width Modulation blocks (PWM)

I2C Master

Serial Peripheral Interface (SPI) Slave

Serial Peripheral Interface (SPI) Master
Note:
Only one interface may be selected at any time.
The modes are selected by setting the CNFGx pins.
The following sections describe each peripheral in detail.
5.1 General Purpose Input Output
FT311D provides up to 7 configurable Input/Output pins. All pins are independently configurable to be
either inputs or outputs.
5.2 UART Interface
When the peripheral interface is configured in UART mode, the interface implements a standard
asynchronous serial UART port with flow control, for example RS232/422/485. The UART can support
baud rates from 300 baud to 6 Mbaud.
Data transfer uses NRZ (Non-Return to Zero) data format consisting of 1 start bit, 7 or 8 data bits, an
optional parity bit, and one or two stop bits. When transmitting the data bits, the least significant bit is
transmitted first. Transmit and receive waveforms are illustrated in Figure 5-1 and Figure 5-2:
Figure 5-1 UART Receive Waveform
Figure 5-2 UART Transmit Waveform
Baud rate (default =9600 baud), flow control settings (default = RTS/CTS), number of data bits
(default=8), parity (default is no parity) and number of stop bits (default=1) are all configurable from the
Android application. Please refer to
http://www.ftdichip.com/Support/Documents/ProgramGuides.htm/FT311_Android_Programmers_Guide.p
df for further details.
uart_tx_active is transmit enable, this output may be used in RS485 designs to control the transmit of
the line driver.
Copyright © 2012 Future Technology Devices International Limited
12
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
5.2.1 UART Mode Signal Descriptions
The UART signals are fixed on the I/O pins. Table 5.1 UART Interface, details the pins for each of the
UART signals.
Pin No
Name
Type
Description
uart_txd
Output
Transmit asynchronous data output
uart_rxd
Input
Receive asynchronous data input
uart_rts#
Output
Request to send control output
26
uart_cts#
Input
Clear to send control input
29
uart_tx_active
output
Transmit enable (typically used for
RS485 designs)
23
24
25
Table 5.1 UART Interface
5.3 Pulse Width Modulation
FT311D provides 4 Pulse Width Modulation (PWM) outputs. These can be used to generate PWM signals
which can be used to control motors, DC/DC converters, AC/DC supplies, etc. Further information is
available in an Application Note AN_140 - Vinculum-II PWM Example.
The features of the PWM module are as follows:
-
4 PWM outputs
-
Variable frequency
-
Variable duty cycle
5.4 I2C
I2C (Inter Integrated Circuit) is a multi-master serial bus invented by Philips. I2C uses two bi-directional
open-drain wires called serial data (SDA) and serial clock (SCL). Common I²C bus speeds are the 100
kbit/s standard mode (SM), 400 kbit/s fast mode (FM), 1 Mbit/s Fast mode plus (FM+), and 3.4 Mbit/s
High Speed mode (HS)
An I2C bus node can operate either as a master or a slave:

Master node
– issues the clock and addresses slaves

Slave node
– receives the clock line and address.
FT311D provides an I2C master interface for connection to other I2C Slave interfaces up to 125kbit/s.
The master is initially in master transmit mode by sending a start bit followed by the 7-bit address of the
slave it wishes to communicate with, which is finally followed by a single bit representing whether to
write(0) to, or read(1) from the slave.
Copyright © 2012 Future Technology Devices International Limited
13
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
If the slave exists on the bus then it will respond with an ACK bit (active low for acknowledged) for that
address. The master then continues in either transmit or receive mode (according to the read/write bit it
sent), and the slave continues in its complementary mode (receive or transmit, respectively).
The address and the data bytes are sent most significant bit first. The start bit is indicated by a high-tolow transition of SDA with SCL high; the stop bit is indicated by a low-to-high transition of SDA with SCL
high.
If the master has to write to the slave then it repeatedly sends a byte with the slave sending an ACK bit.
(In this situation, the master is in master transmit mode and the slave is in slave receive mode.)
If the master has to read from the slave then it repeatedly receives a byte from the slave, the master
sending an ACK bit after every byte but the last one. (In this situation, the master is in master receive
mode and the slave is in slave transmit mode.)
The master then ends transmission with a stop bit, or it may send another START bit if it wishes to retain
control of the bus for another transfer (a "combined message").
I²C defines three basic types of message, each of which begins with a START and ends with a STOP:

Single message where a master writes data to a slave;

Single message where a master reads data from a slave;

Combined messages, where a master issues at least two reads and/or writes to one or more
slaves
In a combined message, each read or write begins with a START and the slave address. After the first
START, these are also called repeated START bits; repeated START bits are not preceded by STOP bits,
which is how slaves know the next transfer is part of the same message.
Please refer to the I2C specification for more information on the protocol.
5.5 Serial Peripheral Interface – SPI Modes
The Serial Peripheral Interface Bus is an industry standard communications interface. Devices
communicate in Master / Slave mode, with the Master initiating the data transfer.
FT311D has one master module and one slave module. Both the SPI master and slave module has four
signals – clock, slave select, MOSI (master out – slave in) and MISO (master in – slave out). Table 5.2
lists how the signals are named in each module.
Module
SPI Slave
SPI
Master
Table 5.2
Signal Name
Type
Description
spi_s_clk
Input
Clock input
spi_s_ss#
Input
Active low slave select input
spi_s_mosi
Input
Master out serial in
spi_s_miso
Output
Master in slave out
spi_m_clk
Output
Clock output – master
spi_m_mosi
Output
Master out slave in - master
spi_m_miso
Input
Master in slave out - master
spi_m_ss_0#
Output
Active low slave select 0 from master to slave 0
SPI Signal Names
The SPI slave protocol by default does not support any form of handshaking. It is simply transferring 8
bit data.
5.5.1 SPI Clock Phase Modes
SPI interface has 4 unique modes of clock phase (CPHA) and clock polarity (CPOL), known
as Mode 0, Mode 1, Mode 2 and Mode 3. Table 5.3 summarizes these modes and available interface and
Figure 5-3 is the function timing diagram.
For CPOL = 0, the base (inactive) level of SCLK is 0.
Copyright © 2012 Future Technology Devices International Limited
14
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
In this mode:
• When CPHA = 0, data is clocked in on the rising edge of SCLK, and data is clocked out on
the falling edge of SCLK.
• When CPHA = 1, data is clocked in on the falling edge of SCLK, and data is clocked out on
the rising edge of SCLK
For CPOL =1, the base (inactive) level of SCLK is 1.
In this mode:
• When CPHA = 0, data is clocked in on the falling edge of SCLK, and data is clocked out on
the rising edge of SCLK
• When CPHA =1, data is clocked in on the rising edge of SCLK, and data is clocked out on
the falling edge of SCLK.
Mode
CPOL
CPHA
0
0
0
1
0
1
2
1
0
3
1
1
Table 5.3
- Clock Phase/Polarity Modes
Figure 5-3 - SPI CPOL CPHA Function
Copyright © 2012 Future Technology Devices International Limited
15
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
5.5.2 Serial Peripheral Interface – Slave
CLK
SS#
External - SPI Master
MOSI
FT311 - SPI Slave
MISO
Figure 5-4 SPI Slave block diagram
FT311D has an SPI Slave module that uses four wire interfaces: MOSI, MISO, CLK and SS#. An SPI
transfer can only be initiated by the SPI Master and begins with the slave select signal being asserted.
This is followed by a data byte being clocked out with the master supplying CLK. The master always
supplies the first byte, which is called a command byte. After this the desired number of data bytes are
transferred before the transaction is terminated by the master de-asserting slave select. An SPI Master is
able to abort a transfer at any time by de-asserting its SS# output. This will cause the Slave to end its
current transfer and return to idle state.
5.5.2.1 SPI Slave Signal Descriptions
Pin No
Name
Type
Description
29
spi_s0_clk
Input
Slave clock input
30
spi_s0_mosi
Input
Master Out Slave In
31
Synchronous data from master to slave
Master In Slave Out
spi_s0_miso
Output
Synchronous data from slave to master
26
spi_s0_ss#
Input
Slave select
Table 5.4 Data and Control Bus Signal Mode Options - SPI Slave Interface
5.5.3 Serial Peripheral Interface – SPI Master
CLK
SS#
FT311 - SPI Master
MOSI
External - SPI Slave
MISO
Figure 5-5 SPI Master block diagram
The SPI Master interface is used to interface to applications such as Real time clocks and audio codecs.
The SPI Master provides the following features:
Copyright © 2012 Future Technology Devices International Limited
16
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305

Synchronous serial data link.

Full and half duplex data transmission.

Serial clock with programmable frequency, polarity and phase.

One slave select output.
5.5.3.1 SPI Master Signal Descriptions.
Table 5.5 shows the SPI master signals and the pins
Pin No
Name
Type
Description
29
spi_m_clk
Output
SPI master clock input
30
spi_m_mosi
Output
31
spi_m_miso
26
spi_m_ss_0#
Master Out Slave In
Synchronous data from master to slave
Master In Slave Out
Input
Synchronous data from slave to master
Active low slave select 0 from master to
Output
slave
Table 5.5 SPI Master Signal Names
The main purpose of the SPI Master block is to transfer data between an external SPI interface and the
FT311D.
An SPI master interface transfer can only be initiated by the SPI Master and begins with the slave select
signal being asserted. This is followed by a data byte being clocked out with the master supplying SCLK.
The master typically supplies the first byte, which is called a command byte. After this the desired
number of data bytes are transferred before the transaction is terminated by the master de-asserting
slave select. However the FT311D is simply a data pipe and no command is required by the FT311D itself.
Any command protocol would be defined by the Android application.
The SPI Master will transmit on MOSI as well as receive on MISO during every data stage.
Figure 5-6 Typical SPI Master Timing and Table 5.6 SPI Master Timing show an example of this.
Copyright © 2012 Future Technology Devices International Limited
17
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Figure 5-6 Typical SPI Master Timing
Time
Description
Minimum
Typical
Maximum
t1
SCLK period
39.68
41.67
t2
SCLK high period
19.84
20.84
21.93
ns
t3
SCLK low period
19.84
20.84
21.93
ns
t4
SCLK driving edge to
MOSI/SS
-1.5
t5
MISO setup time to sample
SCLK edge
t6
MISO hold time from sample
SCLK edge
ns
3
6.5
0
Unit
ns
ns
ns
Table 5.6 SPI Master Timing
Copyright © 2012 Future Technology Devices International Limited
18
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
6
USB Error Detection
Pin 32 (IOBUS7) of the device is provided to indicate a problem has occurred with the USB connection.
Typical errors include USB Device Not Supported, which would occur if the USB port was connected to a
non-Android class device port e.g. the FT311D is not designed to host memory sticks or printers etc. USB
Device Not Responding and Hub not supported would be reported also if connected to a hub. The signal
states are as follows:
Pin state
Definition
Logic 0
Device connected to USB and functional
Logic 1
Device not connected
One 50ms logic 0 pulse
Device not responding. This pulse occurs at plug-in
and then the signal returns to logic 1. This then
repeats at a 1 second interval.
Two 50ms logic 0 pulses
Device not supported. These pulses occur at plugin and then the signal returns to logic 1. This then
repeats at a 1 second interval.
Three 50ms logic 0 pulses
Hub not supported. These pulses occur at plug-in
and then the signal returns to logic 1. This then
repeats at a 1 second interval.
Table 6.1 Error Detection
Copyright © 2012 Future Technology Devices International Limited
19
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
7
Absolute Maximum Ratings
The absolute maximum ratings for FT311D are shown in Table 7.1. These are in accordance with the
Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the
device.
Parameter
Value
Unit
Storage Temperature
-65°C to 150°C
Degrees C
168 Hours
Floor Life (Out of Bag) At Factory Ambient
(IPC/JEDEC J-STD-033A MSL Level 3
( 30°C / 60% Relative Humidity)
Hours
Compliant)*
Degrees
Ambient Temperature (Power Applied)
-40°C to 85°C
Vcc Supply Voltage
0 to +3.63
V
VCC_IO
0 to +3.63
V
VCC_PLL_IN
0 to + 1.98
V
DC Input Voltage - USBDP and USBDM
-0.5 to +(Vcc +0.5)
V
-0.5 to +5.00
V
DC Input Voltage - All other Inputs
-0.5 to +(Vcc +0.5)
V
DC Output Current - Outputs
4
mA
4
mA
DC Input Voltage - High Impedance
Bidirectional
DC Output Current - Low Impedance
Bidirectional
Table 7.1
*
C.
Absolute Maximum Ratings
If devices are stored out of the packaging beyond this time limit the devices should be baked
before use. The devices should be ramped up to a temperature of 125°C and baked for up to 17
hours.
7.1 DC Characteristics
DC Characteristics (Ambient Temperature -40˚C to +125˚C)
Parameter
Vcc1
Description
VCC Operating Supply
Voltage
Minimum
Typical
Maximum
Units
2.97
3.3
3.63
V
Copyright © 2012 Future Technology Devices International Limited
Conditions
20
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Vcc2
VCC_PLL
VCCIO Operating Supply
Voltage
VCC_PLL Operating
Supply Voltage
2.97
3.3
3.63
V
1.62
1.8
1.98
V
Operating Supply Current
Icc1
25
mA
128
µA
48MHz
Icc2
Operating Supply Current
Normal
Operation
USB Suspend
Table 7.2 Operating Voltage and Current
Parameter
Description
Minimum
Voh
Output Voltage High
2.4
Vol
Output Voltage Low
Vin
Typical
Maximum
0.4
Input Switching
1.5
Threshold
Units
Conditions
V
I source = 8mA
V
I sink = 8mA
V
Table 7.3 I/O Pin Characteristics
Parameter
UVoh
UVol
UVse
UCom
UVdif
UDrvZ
Description
I/O Pins Static Output
( High)
Minimum
Typical
2.8
0.3
V
0.8
2.0
V
0.8
2.5
V
( Low )
Threshold
Differential Common
Mode
Differential Input
Sensitivity
Driver Output
Impedance
Units
0.2
3
Conditions
V
I/O Pins Static Output
Single Ended Rx
Maximum
V
6
9
Ohms
Table 7.4 USB I/O Pin (USBDP, USBDM) Characteristics
Copyright © 2012 Future Technology Devices International Limited
21
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Parameter
Description
Minimum
Typical
Maximum
Units
1.62
1.8
1.98
V
1.62
1.8
1.98
V
-40
25
125
°C
-10
±1
10
µA
-10
±1
10
µA
Power supply of internal
VCCK
core cells and I/O to core
interface
VCC18IO
Power supply of 1.8V
OSC pad
Operating junction
TJ
temperature
Iin
Input leakage current
Ioz
Tri-state output leakage
current
Conditions
1.8V power
supply
1.8V power
supply
Iin = VCC18IO or
0V
Table 7.5 Crystal Oscillator 1.8 Volts DC Characteristics
7.2 ESD and Latch-up Specifications
Description
Specification
Human Body Mode (HBM)
± 2000V
Machine mode (MM)
± 200V
Charged Device Mode (CDM)
± 500V
Latch-up
> ± 200mA
Table 7.6 ESD and Latch-up Specifications
Copyright © 2012 Future Technology Devices International Limited
22
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8
Application Examples
The following sections illustrate possible applications of the FT311D.
8.1 USB to GPIO Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
0.1uF
3V3
Ferrite
Bead
1
VCC
VBUSCTRL#
470R
470R
470R
470R
VCCIO
5V_SW
IOBUS0
RESET#
27R
2
USBDM
IOBUS1
3
USBDP
27R
4
IOBUS2
5
47pF
47pF
IOBUS3
SHIELD
FT311D
100nF
IOBUS4
CNFG2
GND
CNFG1
IOBUS5
CNFG0
GND
GND
IOBUS6
1V8 PLL VCC IN
IOBUS7
3V3
GN
D
AG
ND
VREGOUT
GND
100nF
+
4.7uF
100nF
GND
GND
Figure 8.1 Application Example showing USB to GPIO Converter
This example shows the CNFGx pins set for mode 000 – GPIO.
IOBUS0-3 are configured as outputs by the Android application to control the LEDs.
IOBUS4-6 pins are configured as inputs to allow the buttons to control actions in the Android application.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
23
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.2 USB to UART Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
Ferrite
Bead
1
VCC
VBUSCTRL#
VCCIO
5V_SW
0.1uF
UART_TXD
IOBUS0
RESET#
27R
2
USBDM
IOBUS1
3
UART_RXD
USBDP
27R
4
IOBUS2
5
47pF
47pF
IOBUS3
SHIELD
FT311D
100nF
CNFG1
UART_CTS#
UART_TX_ACTIVE
IOBUS5
CNFG0
GND
MCU/FPGA
IOBUS4
CNFG2
GND
UART_RTS#
GND
IOBUS6
1V8 PLL VCC IN
10k
IOBUS7
3V3
3V3
100nF
+
4.7uF
GN
D
AG
ND
VREGOUT
100nF
GND
GND
Figure 8.2 Application Example showing USB to UART Converter
This example shows the CNFGx pins set for mode 001 - UART.
The UART signals are at 3V3 level and may be used to drive directly into a FPGA or MCU with a 3V3
interface, or could be level shifted with an RS232, RS422 or RS485 transceiver. The UART_TX_ACTIVE
signal is used mostly with RS485 transceivers to enable the transmit drivers.
The unused pins may be left unterminated.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
24
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.3 USB to PWM Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
Ferrite
Bead
1
VCC
VBUSCTRL#
VCCIO
5V_SW
PWM_0
IOBUS0
RESET#
27R
2
0.1uF
MOTOR
CONTROLLER
3V3
USBDM
3
IOBUS1
PWM_1
IOBUS2
PWM_2
USBDP
27R
4
5
47pF
47pF
IOBUS3
SHIELD
470R
PWM_3
FT311D
100nF
IOBUS4
CNFG2
GND
CNFG1
IOBUS5
CNFG0
GND
IOBUS7
10k
3V3
+
4.7uF
GN
D
AG
ND
VREGOUT
3V3
100nF
IOBUS6
1V8 PLL VCC IN
GND
100nF
GND
GND
Figure 8.3 Application Example showing USB to PWM Converter
This example shows the CNFGx pins set for mode 010 – Pulse Width Modulation (PWM).
PWM channel 0 has been wired to a motor controller. This is typical of applications with robotic arms or
moving machinery.
PWM channel 3 has been connected to an LED. This allows the LED to either flash or by altering the PWM
switching frequency the controller can act as a “dimmer switch” to the LED.
The unused channels may be left unterminated.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
25
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.4 USB to I2C (Master) Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
0.1uF
3V3
10k
Ferrite
Bead
1
VCC
VCCIO
5V_SW
10k
VBUSCTRL#
I2C_CLK
IOBUS0
RESET#
27R
2
USBDM
I2C_DATA
IOBUS1
3
I2C Peripheral
e.g. Memory,
RTC, CODECs
USBDP
27R
4
IOBUS2
5
47pF
47pF
IOBUS3
SHIELD
FT311D
100nF
IOBUS4
CNFG2
GND
CNFG1
IOBUS5
CNFG0
GND
IOBUS7
10k
3V3
+
4.7uF
GN
D
AG
ND
VREGOUT
3V3
100nF
IOBUS6
1V8 PLL VCC IN
GND
100nF
GND
GND
Figure 8.4 Application Example showing USB to I2C (Master) Converter
This example shows the CNFGx pins set for mode 011 – I2C (Master).
Only two signal lines are required for I2C interfacing. The clock is an output from the FT311D while the
data line is bi-directional.
Examples of I2C peripherals include EEPROMs, Real time Clocks (RTC) and audio or video codecs.
The unused pins may be left unterminated.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
26
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.5 USB to SPI (Slave) Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
Ferrite
Bead
1
VCC
0.1uF
VBUSCTRL#
VCCIO
5V_SW
IOBUS0
RESET#
27R
2
USBDM
IOBUS1
3
USBDP
27R
4
3V3
IOBUS2
5
47pF
10k
47pF
IOBUS3
SHIELD
FT311D
100nF
SPI_S_CLK
IOBUS4
CNFG2
GND
SPI_S_SS#
SPI_S_MOSI
CNFG1
IOBUS5
CNFG0
GND
SPI MASTER
e.g. MCU,
FPGA
SPI_S_MISO
IOBUS6
1V8 PLL VCC IN
GND
IOBUS7
3V3
100nF
+
4.7uF
GN
D
AG
ND
VREGOUT
100nF
GND
GND
Figure 8.5 Application Example showing USB to SPI (Slave) Converter
This example shows the CNFGx pins set for mode 100 – SPI (Slave).
The external SPI Master controls the slave select line and the clock to the FT311D.
SPI_S_MOSI is the FT311D data input line which may be Most or Least Significant Bit first.
SPI_S_MISO is the FT311D data output line which may be Most or Least Significant Bit first.
Example SPI masters include MCU‟s and FPGA‟s
The unused pins may be left unterminated.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
27
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
8.6 USB to SPI (Master) Converter
P Channel Power
MOSFET
5V_SW
Switched 5V Power to
USB
5V
3V3
REGULATOR
0.1uF
3V3
Ferrite
Bead
1
VCC
0.1uF
VBUSCTRL#
VCCIO
5V_SW
IOBUS0
RESET#
27R
2
USBDM
IOBUS1
3
USBDP
27R
4
3V3
IOBUS2
10k
IOBUS3
5
47pF
47pF
SHIELD
FT311D
100nF
SPI_M_CLK
IOBUS4
CNFG2
GND
SPI_M_SS#
SPI_M_MOSI
CNFG1
IOBUS5
CNFG0
GND
SPI SLAVE
e.g. EEPROM,
RTC, CODECs
SPI_M_MISO
IOBUS6
1V8 PLL VCC IN
GND
IOBUS7
3V3
100nF
+
4.7uF
GN
D
AG
ND
VREGOUT
100nF
GND
GND
Figure 8.6 Application Example showing USB to SPI (Master) Converter
This example shows the CNFGx pins set for mode 101 – SPI (Master).
The FT311D SPI Master controls the slave select line and the clock to the external SPI slave.
SPI_M_MOSI is the FT311D data output line which may be Most or Least Significant Bit first.
SPI_M_MISO is the FT311D data input line which may be Most or Least Significant Bit first.
Example SPI Slave devices include memory, RTC, and codec devices.
The unused pins may be left unterminated.
Power to the USB port is enabled by the VBUSCTRL# signal
Copyright © 2012 Future Technology Devices International Limited
28
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
9
Package Parameters
FT311D is available in RoHS Compliant packages, QFN package (32QFN) and an LQFP package (32LQFP).
The packages are lead (Pb) free and use a „green‟ compound. The package is fully compliant with
European Union directive 2002/95/EC.
The mechanical drawings of the packages are shown in sections 9.2- all dimensions are in millimetres.
The solder reflow profile for all packages can be viewed in Section 9.3.
9.1 FT311D Package Markings
9.1.1 QFN-32
An example of the markings on the QFN package are shown in Figure 9-1. The FTDI part number is too
long for the 32 QFN package so in this case the last two digits are wrapped down onto the date code line.
FTDI
II
XXXXXXXX
FT311D-32Q
1C YYWW
32
Line 1 – FTDI Logo
Line 2 – Wafer Lot Number
Line 3 – FTDI Part Number
Line 4 – Revision and Date
Code
1
Figure 9-1 QFN Package Markings
1C should be printed on line 4, then a space and then the Date Code.
1. YYWW = Date Code, where YY is year and WW is week number
2. Marking alignment should be centre justified
3. Laser Marking should be used
4. All marking dimensions should be marked proportionally. Marking font should be using
Unisem standard font (Roman Simplex)
Copyright © 2012 Future Technology Devices International Limited
29
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
9.1.2 LQFP-32
An example of the markings on the LQFP package are shown in Figure 9-2.
FTD
I
XXXXXXXXXX
FT311D-L 1C
YYWW
32
Line 1 – FTDI Logo
Line 2 – Wafer Lot Number
Line 3 – FTDI Part Number
Line 4 – Date Code
1
Figure 9-2 LQFP Package Markings
Notes:
1. YYWW = Date Code, where YY is year and WW is week number
2. Marking alignment should be centre justified
3. Laser Marking should be used
4. All marking dimensions should be marked proportionally. Marking font should be using Unisem
standard font (Roman Simplex)
Copyright © 2012 Future Technology Devices International Limited
30
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
9.2 FT311D Package Dimensions
9.2.1 QFN-32 Package Dimensions
FTDl
XXXXXXXX
FT311D-32Q
1C YYWW
1
1
Figure 9-3 QFN-32 Package Dimensions
Note: Dimensions are in mm
Copyright © 2012 Future Technology Devices International Limited
31
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Note: The centre pad should be connected to the GND plane for improved thermal conduction and noise
immunity.
9.2.2
LQFP-32 Package Dimensions
FTDl
XXXXXXXX
FT311D-32L
1C YYWW
PIN #32
PIN #1
Figure 9-4 LQFP-32 Package Dimensions
Note: Dimensions are in mm
Copyright © 2012 Future Technology Devices International Limited
32
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
9.3 Solder Reflow Profile
Figure 9-5 All packages Reflow Solder Profile
Copyright © 2012 Future Technology Devices International Limited
33
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Pb Free Solder Process
SnPb Eutectic and Pb free (non
(green material)
green material) Solder Process
3°C / second Max.
3°C / Second Max.
Profile Feature
Average Ramp Up Rate (Ts to Tp)
Preheat
- Temperature Min (Ts Min.)
150°C
100°C
- Temperature Max (Ts Max.)
200°C
150°C
- Time (ts Min to ts Max)
60 to 120 seconds
60 to 120 seconds
217°C
183°C
60 to 150 seconds
60 to 150 seconds
260°C
see Figure 9-5
30 to 40 seconds
20 to 40 seconds
Ramp Down Rate
6°C / second Max.
6°C / second Max.
Time for T= 25°C to Peak Temperature, Tp
8 minutes Max.
6 minutes Max.
Volume mm3 < 350
Volume mm3 >=350
< 2.5 mm
235 +5/-0 deg C
220 +5/-0 deg C
≥ 2.5 mm
220 +5/-0 deg C
220 +5/-0 deg C
Time Maintained Above Critical Temperature
TL:
- Temperature (TL)
- Time (tL)
Peak Temperature (Tp)
Time within 5°C of actual Peak Temperature
(tp)
Table 9.1
Reflow Profile Parameter Values
SnPb Eutectic and Pb free (non green material)
Package Thickness
Pb Free (green material) = 260 +5/-0 deg C
Table 9.2
Package Reflow Peak Temperature
Copyright © 2012 Future Technology Devices International Limited
34
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
10 Contact Information
Head Office – Glasgow, UK
Future Technology Devices International Limited
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Branch Office – Taipei, Taiwan
Future Technology Devices International Limited
(Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan, R.O.C.
Tel: +886 (0) 2 8791 3570
Fax: +886 (0) 2 8791 3576
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Branch Office – Hillsboro, Oregon, USA
Future Technology Devices International Limited (USA)
7235 NW Evergreen Parkway, Suite 600
Hillsboro, OR 97123-5803
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-Mail (Sales)
E-Mail (Support)
E-Mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Branch Office – Shanghai, China
Room 1103, No. 666 West Huaihai Road,
Shanghai, 200052
China
Tel: +86 21 62351596
Fax: +86 21 62351595
E-mail (Sales)
[email protected]
[email protected]
E-mail (Support)
E-mail (General Enquiries)
[email protected]
Copyright © 2012 Future Technology Devices International Limited
35
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Appendix A – References
Useful Application Notes
http://www.ftdichip.com/Documents/White_Papers/WP_001_Connecting_Peripherals_to_an_Android_Plat
form.pdf
http://www.ftdichip.com/Support/Documents/ProgramGuides.htm/FT311_Android_Programmers_Guide.p
df
Useful utilities and examples firmware
http://www.ftdichip.com/Android/FT311Configuration.zip
http://www.ftdichip.com/Android/SampleApps.zip
Copyright © 2012 Future Technology Devices International Limited
36
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Appendix B - List of Figures and Tables
List of Figures
Figure 2.1 FT311D Block Diagram ................................................................................................... 3
Figure 3.1 QFN Schematic Symbol .................................................................................................. 6
Figure 5-1 UART Receive Waveform .............................................................................................. 12
Figure 5-2 UART Transmit Waveform ............................................................................................ 12
Figure 5-4 - SPI CPOL CPHA Function ............................................................................................ 15
Figure 5-5 SPI Slave block diagram............................................................................................... 16
Figure 5-6 SPI Master block diagram ............................................................................................. 16
Figure 5-7 Typical SPI Master Timing ............................................................................................ 18
Figure 7.1 Application Example showing USB to GPIO Converter ....................................................... 23
Figure 8.2 Application Example showing USB to UART Converter ...................................................... 24
Figure 8.3 Application Example showing USB to PWM Converter ....................................................... 25
Figure 8.4 Application Example showing USB to I2C (Master) Converter ............................................. 26
Figure 8.5 Application Example showing USB to SPI (Slave) Converter .............................................. 27
Figure 8.6 Application Example showing USB to SPI (Master) Converter ............................................ 28
Figure 9-1 QFN Package Markings ................................................................................................. 29
Figure 9-2 LQFP Package Markings ................................................................................................ 30
Figure 9-4 LQFP-32 Package Dimensions ....................................................................................... 32
Figure 9-5 All packages Reflow Solder Profile ................................................................................. 33
List of Tables
Table 3.1 Power and Ground .......................................................................................................... 6
Table 3.2 Common Function pins .................................................................................................... 7
Table 3.3 Interface Pins ................................................................................................................. 8
Table 3.4 CBUS Configuration Control ............................................................................................. 8
Table 3.5 I/O Configuration ............................................................................................................ 9
Table 4.1 I/O Peripherals Signal Names ......................................................................................... 11
Table 4.2 Default Descriptor Strings .............................................................................................. 11
Table 5.1 UART Interface ............................................................................................................ 13
Table 5.2
SPI Signal Names ....................................................................................................... 14
Table 5.3
- Clock Phase/Polarity Modes ....................................................................................... 15
Table 5.4 Data and Control Bus Signal Mode Options - SPI Slave Interface ...................................... 16
Table 5.5 SPI Master Signal Names ............................................................................................... 17
Table 5.6 SPI Master Timing........................................................................................................ 18
Table 6.1 Error Detection ............................................................................................................ 19
Table 7.1
Absolute Maximum Ratings .......................................................................................... 20
Table 7.2 Operating Voltage and Current ....................................................................................... 21
Table 7.3 I/O Pin Characteristics ................................................................................................... 21
Table 7.4 USB I/O Pin (USBDP, USBDM) Characteristics .................................................................. 21
Table 7.5 Crystal Oscillator 1.8 Volts DC Characteristics .................................................................. 22
Table 7.6 ESD and Latch-up Specifications .................................................................................... 22
Copyright © 2012 Future Technology Devices International Limited
37
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Table 9.1
Reflow Profile Parameter Values ................................................................................... 34
Table 9.2
Package Reflow Peak Temperature ................................................................................ 34
Copyright © 2012 Future Technology Devices International Limited
38
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Appendix C - Revision History
Document Title:
USB Android Host IC FT311D
Document Reference No.:
FT_000660
Clearance No.:
FTDI# 305
Product Page:
http://www.ftdichip.com/FTProducts.htm
Document Feedback:
Send Feedback
Version 1.0
Initial Release
July 2012
Copyright © 2012 Future Technology Devices International Limited
39
DS_FT311D USB ANDROID HOST IC Datasheet
Version 1.0
Document No.: FT_000660 Clearance No.: FTDI# 305
Copyright © 2012 Future Technology Devices International Limited
40
Similar pages