Ecliptek E1125AMETC-24.000M-CL175 Specification control drawing Datasheet

Marketing Bulletin
DATE:
May 6, 2005
TO:
All Sales Personnel
FROM:
Mark Stoner
RE:
E11 (OS/03) Termination
To all concerned parties,
This bulletin is to notify all customers of the discontinuation of the following Ecliptek
series effective May 1st, 2005:
Series
E11
Description
5V 14 pin DIP ECL Oscillator
Recommended Replacement
None
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of
product termination. New orders will not be accepted after August 1st, 2005, with
delivery to conclude by November 1st 2005.
If there are any questions pertaining to this bulletin, please fell free to contact me.
Thank you again for your cooperation.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234
STANDARD SPECIFICATIONS
Frequency Range:
Frequency Tolerance/Stability:
00
45
25
Operating Temperature Range
Blank
ET
Storage Temperature Range
Supply Voltage (VEE )
Input Current
Output Voltage Logic High
Output Voltage Logic Low
Rise/Fall Time
Duty Cycle
Load Drive Capability
Aging @ 25°C
6.000MHz to 155.520MHz
(All Values Inclusive of Operating Temp. Range, Supply Voltage, and Load)
±100ppm Max.
±50ppm Max.
±25ppm Max. (0°C to +70°C only), (less than or equal to 125.000MHz only)
OBSOLETE
0°C to +70°C
-40°C to +85°C
-55°C to +125°C
-5.2Vdc ±5% (AA, AB, and AM); +5.2Vdc ±5% (AC)
140mA Maximum
-1.0Vdc Min./-0.7Vdc Max. (AA, AB, and AM); 4.0Vdc Min./4.5Vdc M ax. (AC)
-1.95Vdc Min./-1.60Vdc Max. (AA, AB, and AM); 3.00Vdc Min./3.42Vdc Max. (AC)
2nSec Maximum (Measured at 20% to 80% of waveform)
50% ±10% (Measured at 50% of waveform)
50 Ohms into -2.0Vdc (AA, AB, and AM); 50 Ohms into +3.0Vdc (AC)
±5ppm/year Maximum
ENVIRONMENTAL & MECHANICAL
Fine Leak Test:
Gross Leak Test:
Mechanical Shock:
Vibration:
Lead Integrity:
MIL-STD-883, Method
MIL-STD-883, Method
MIL-STD-202, Method
MIL-STD-883, Method
MIL-STD-883, Method
Solderability:
Temperature Cycling:
Resistance to Soldering Heat:
Resistance to Solvents:
1014, Condition A
1014, Condition C
213, Condition C
2007, Condition A
2004
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
PIN CONFIGURATIONS
PIN
1
7
8
14
AA
Ground/Case
-5.2V
Output
Ground
AB
No Connect or Complementary Output
-5.2V
Output
Ground/Case
AC
No Connect or Complementary Output
Ground/Case
Output
+5.2Vdc
AM
No Connect or Complementary Output
Ground/Case
Output
-5.2Vdc
PART NUMBERING GUIDE
E11 00 AM ET C - 24.000M - CL175
Configuration Options
CLXXX = Cut Leads (MAL01-101-000)
G = Gull Wing (MAL01-001-000)
Frequency
Pin 1 Connection
Blank = No Connect
C = Complementary Output
15.240
±0.203
1
0.9 MAX
7
7.620
±0.203
Operating Temperature Range
Blank = 0°C to +70°C
ET = -40°C to +85°C
Pin Configuration
AA, AB, AC, or AM
Per Pin Configuration Table Above
Frequency Tolerance/Stability
00 = ±100ppm Maximum, 45 = ±50ppm Maximum
25 = ±25ppm Maximum
∅0.457
±0.1 (X4)
8
14
5.08
MAX
13.2
MAX
5.08
MIN
MARKING GUIDE
20.8 MAX
(Line #1) ECLIPTEK
ALL DIMENSIONS
IN MILLIMETERS
(Line #2) E11 AM C
Pin 1 Connection
Blank = No Connect
C = Complementary Output
Pin Configuration Per Pin Configuration Table Above
(Line #3) XXX.XXXM
Frequency
(Line #4) XX Y ZZ
ECLIPTEK
E11AMC
XXX.XXXM
XXYZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Code (TEN02-001-000)
SPECIFICATION CONTROL DRAWING
Drawing Number
CSC01-010-000
Title
FULL SIZE ECL OSCILLATOR
Revision
Effectivity Date
E
8675
NOTE: Pin 1 shall be marked with a black dot. Marking shall
conform to conditions listed in TQC41-001-000.
08-27-03
ECN Number
Approved By
PAGE 1 OF 2
Date Released By
Date
Similar pages