MPD E205I E200i sery Datasheet

E200I
Series
High Isolation, 2W
Ultra-Miniature, SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
Parameter
Conditions
5 VDC Input
Min.
4.5
Typ.
5.0
Max.
5.5
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
48 VDC Input
44.0
48.0
52.0
• 2W Output Power
• Ultra-Miniature SIP Case
Input Voltage Range
• 3,000 VDC Isolation
• >2 MHour MTBF
• 18 Standard Models
• Industry Standard Pin-Out
Reverse Polarity Input Current
Input Filter
VDC
0.3
A
Max.
±3.0
Units
%
Internal Capacitor
Output
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation (Note 1)
Conditions
Min.
Typ.
For Vin Change of 1%
±1.2
%
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
Output Power Protection
100
mV P - P
±0.02
%/ºC
Max.
Units
VDC
120
Temperature Coefficient
RoHS Compliant
Units
%
±0.01
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Isolation Voltage
Conditions
Isolation Resistance
Isolation Capacitance
60 Seconds
Min.
3,000
1,000 VDC
1,000
100 kHz, 1V
Switching Frequency
Typ.
MΩ
60
pF
125
kHz
Environmental
Parameter
Operating Temperature Range
Conditions
Ambient
Operating Temperature Range
-55
Cooling
MicroPower Direct
Physical
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Size
Case Material
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
MTBF
Typ.
+25
Case
Storage Temperature Range
Humidity
Min.
-40
Max.
+85
Units
ºC
+90
ºC
+125
ºC
95
%
Free Air Convection
RH, Non-condensing
0.46 x 0.29 x 0.40 Inches (11.68 x 7.5 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
Weight
0.06 Oz (1.8g)
Reliability Specifications
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
2.0
Typ.
Max.
Units
MHours
Conditions
Min.
-0.7
Typ.
Max.
9.0
Units
5 VDC Input
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
48 VDC Input
-0.7
55.0
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
VDC
1.5 mm From Case For 10 Sec
260
ºC
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
E201I
Input
Output
Load
Voltage (VDC)
Current (mA)
Voltage Current
Current Regulation
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (% Max)
5
4.5 - 5.5
372
38
3.3
400.0
40.0
12
Efficiency
(%, Typ)
71
Fuse Rating
Slow-Blow
(mA)
1,000
E202I
5
4.5 - 5.5
533
38
5.0
400.0
40.0
12
75
1,000
E203I
5
4.5 - 5.5
500
38
9.0
222.0
22.0
8
79
1,000
E204I
5
4.5 - 5.5
500
38
12.0
167.0
16.0
8
80
1,000
E205I
5
4.5 - 5.5
500
38
15.0
133.0
13.0
8
80
1,000
E211I
12
10.8 - 13.2
150
30
3.3
400.0
40.0
8
73
500
E212I
12
10.8 - 13.2
200
30
5.0
400.0
40.0
8
77
500
E213I
12
10.8 - 13.2
211
30
9.0
222.0
22.0
8
79
500
E214I
12
10.8 - 13.2
199
25
12.0
167.0
16.0
8
84
500
E215I
12
10.8 - 13.2
208
25
15.0
133.0
13.0
8
80
500
E222I
24
21.6 - 26.4
107
12
5.0
400.0
40.0
8
78
200
E223I
24
21.6 - 26.4
102
12
9.0
222.0
22.0
8
82
200
E224I
24
21.6 - 26.4
104
12
12.0
167.0
16.0
8
80
200
E225I
24
21.6 - 26.4
102
12
15.0
133.0
13.0
8
82
200
E232I
48
44.0 - 52.0
53
6
5.0
400.0
40.0
8
78
100
E233I
48
44.0 - 52.0
52
6
9.0
222.0
22.0
8
80
100
E234I
48
44.0 - 52.0
53
6
12.0
167.0
16.0
8
78
100
E235I
48
44.0 - 52.0
52
6
15.0
133.0
13.0
8
80
100
Notes:
1. Output load regulation is specified for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33
µF ceramic capacitor be placed from the +Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units. However, they may
not meet all specifications.
4. The 5V, 12V and 24V input units do not require external components to
operate, but the use of a low ESR capacitor (approximately 10 µF, ESR
<1.0Ω at 100 kHz) mounted close to the converter input pins is recommended.
For 48 VDC input units, an input capacitor should always be used. Dependent upon the application, a value between 4.7 µF and 47 µF should be
sufficient.
5. Out put capacitive load capability of these units is 33 µF max. Exceeding
this may cause start up problems.
5. It is recommended that a fuse be used on the input of a power supply
for protection. See the table above for the correct rating.
Pin Connections
Pin
Description
1
-Vin
2
+Vin
3
-Vout
4
+Vout
Derating Curve
Mechanical Dimensions
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation
on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages