Ecliptek E32W2F3C1D-155.520M Oscillator Datasheet

Marketing Bulletin
DATE:
August 25th, 2005
TO:
All Sales Personnel
FROM:
Mark Stoner
RE:
Product Termination
To all concerned parties,
This bulletin is to notify all customers of the discontinuation of the following Ecliptek
series effective August 25th, 2005:
Series
E31W2
E32W2
Description
5V 6 pad SMD LVPECL VCXO
3.3V 6 pad SMD LVPECL VCXO
Recommended Replacement
E32D1
E32D1
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of
product termination. New orders will not be accepted after November 25th, 2005, with
delivery to conclude by February 25th 2006.
If there are any questions pertaining to this bulletin, please fell free to contact me.
Thank you again for your cooperation.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234
E31W2 Series
E31W2
• PECL Output VCXO
• 5.0V supply voltage
• 6 pad PCB SMD package
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
OBSOLETE
H 5.5
L 14.8
W 9.8
OSCILLATOR
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
5.0VDC ±5%
Input Current
100mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Additional Output / Logic Control
No Connect and Single Output
Enable/Disable and Single Output
No Connect and Complementary Output or
Enable/Disable and Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
Absolute Pull Range (APR)
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum
1 pSec Maximum
Load, and Aging @25°C over 10 years
Linearity
20%, 15%, or 10% Maximum
Control Voltage (VC): Test Conditions for APR
2.5VDC ±2.0VDC
Control Voltage Range (VCR)
0.0VDC to VCC
Center Control Voltage
2.5VDC
Transfer Function
Positive Transfer Characteristic
Input Impedance
50kOhms Typical
Modulation Bandwidth
10kHz Minimum
at -3dB with Control Voltage of +2.5VDC
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E31J2
6-PCB
5.0V
OS80
01/03
800-ECLIPTEK www.ecliptek.com for latest revision
196
Specifications subject to change without notice.
OBSOLETE
PART NUMBERING GUIDE
E31W2 F 3 A 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR = Tape and Reel (Standard)
FREQUENCY
ADDITIONAL OUTPUT/LOGIC CONTROL
A=No Connect and Single Output
B=Enable/Disable and Single Output
C=No Connect and Complementary Output
D=Enable/Disable and Complementary Output
APR
3=±50ppm Minimum
LINEARITY
A=20%
B=15%
C=10%
DUTY CYCLE
1=50 ±10(%), 2=50 ±5(%)
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
SIDE VIEW
TOP VIEW
FRONT VIEW
Pin 1: Voltage Control
Pin 4: Output
Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect
Pin 3: Case Ground
Pin 6: Supply Voltage
Tolerances = ±0.1
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Characteristic
Specification
Line 1: ECLIPTEK
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Line 2: XX.XXX M
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E31W2
6-PCB
5.0V
OS80
01/03
800-ECLIPTEK www.ecliptek.com for latest revision
197
Specifications subject to change without notice.
E32W2 Series
E32W2
• PECL Output VCXO
• 3.3V supply voltage
• 6 pad PCB SMD package
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
OBSOLETE
H 5.5
L 14.8
W 9.8
OSCILLATOR
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
3.3VDC ±5%
Input Current
75mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Additional Output / Logic Control
No Connect and Single Output
Enable/Disable and Single Output
No Connect and Complementary Output or
Enable/Disable and Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
Absolute Pull Range (APR)
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum
1 pSec Maximum
Load, and Aging @25°C over 10 years
Linearity
20%, 15%, or 10% Maximum
Control Voltage (VC): Test Conditions for APR
1.65VDC ±1.35VDC
Control Voltage Range (VCR)
0.0VDC to VCC
Center Control Voltage
1.65VDC
Transfer Function
Positive Transfer Characteristic
Input Impedance
50kOhms Typical
Modulation Bandwidth
MANUFACTURER
CATEGORY
ECLIPTEK CORP.
OSCILLATOR
10kHz Minimum
at -3dB with Control Voltage of +1.65VDC
SERIES
E32W2
800-ECLIPTEK www.ecliptek.com for latest revision
PACKAGE
VOLTAGE
CLASS
REV.DATE
6-PCB
3.3V
OS79
01/03
198
Specifications subject to change without notice.
OBSOLETE
PART NUMBERING GUIDE
E32W2 F 3 A 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR = Tape and Reel (Standard)
FREQUENCY
ADDITIONAL OUTPUT/LOGIC CONTROL
A=No Connect and Single Output
B=Enable/Disable and Single Output
C=No Connect and Complementary Output
D=Enable/Disable and Complementary Output
APR
3=±50ppm Minimum
LINEARITY
A=20%
B=15%
C=10%
DUTY CYCLE
1=50 ±10(%), 2=50 ±5(%)
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
SIDE VIEW
TOP VIEW
FRONT VIEW
Pin 1: Voltage Control
Pin 4: Output
Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect
Pin 3: Case Ground
Pin 6: Supply Voltage
Tolerances = ±0.1
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Characteristic
Specification
Line 1: ECLIPTEK
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Line 2: XX.XXX M
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
ECLIPTEK CORP.
OSCILLATOR
E32W2
6-PCB
3.3V
OS79
800-ECLIPTEK www.ecliptek.com for latest revision
REV.DATE
01/03
199 Specifications subject to change without notice.
Similar pages