HP E3642A Programmable dc power supply Datasheet

Agilent
E3640A – E3649A
Programmable DC Power Supplies
Data Sheet
Reliable Power, Repeatable Results
‡
Single and dual outputs
‡
Dual range output
‡
30 W to 100 W output power
‡
Front and rear output terminals
‡
Over-voltage protection
‡
Remote Sensing
‡
GPIB and RS-232 standard
‡
Save and recall functions
Great Performance,
Outstanding Price
With the output power of 30 to
100 W, the Agilent E364xA Series
programmable DC power supplies
provide great performance at a great
price. All ten models deliver clean
power, excellent regulation, fast
transient response and built-in GPIB
and RS-232 interfaces. They are
designed to meet the needs of R&D
design verification, production testing,
QA verifications, and other demanding
applications with Agilent
Technologies’s quality and reliability.
Steady Output
With 0.01 percent load and line
regulation, Agilent E364xA power
supplies are able to maintain a steady
output when power line and load
changes occur. They also specify
normal mode voltage noise and low
common mode current noise. The
low normal mode noise specification
assures clean power for precision
circuitry applications, and the low
common mode current provides
isolation from power line current
injection. Agilent E364xA power
supplies specify less than 90 msec
of voltage settling time at any output
load condition.
Remote Interface
Agilent E364xA power supplies
support any PC with a GPIB (IEEE-488)
card or RS-232 interface. Every model
ships standard with both GPIB and
RS-232. The easy-to-use SCPI
(Standard Commands for
Programmable Instruments) allow fast
and simple programming procedures.
Besides, the user manual provides
sufficient information on programming
for all end users, from beginners to
veterans.
Broad Support
VXI plug and play software drivers are
available for Agilent VEE, National
Instruments LabViewTM and
LabWindowsTM. With these drivers,
integration of the E364xA into your
system can never be any easier. The
drivers are supported under Microsoft®
Windows 98® and NT®.
Front Panel Operation
An easy-to-use rotary knob and selfguiding keypads allow you to set the
output at your desired resolution
without any effort. Also, both voltage
and current levels can be set to a
maximum resolution of 10 mV/1 mA
from the front panel. In addition, you
can store and recall for up to five
complete power supply setups using
the internal non-volatile memory.
2
The output on/off button sets the
output to zero. If you own a dual
output model, you can view two
voltages or currents that are displayed
simultaneously.
Versatile Power
Agilent E364xA power supplies give
you the flexibility to select from dual
output ranges. Output load is
protected against overvoltage, which
can be easily monitored and adjusted
from the front panel and remote
interface. Remote sensing is available
in the rear terminal to eliminate errors
caused by voltage drops on the load
leads. These power supplies offer new
versatile binding posts on the front
panel and screw-type terminals on the
rear panel. New front panel binding
posts allow you to use safety test
leads as well as conventional banana
clips and stripped wires. An optional
rackmount kit is available. The Agilent
E364xA Series employs a cooling
fan with automatic speed control to
reduce the acoustic noise.
LabView and LabWindows are
registered trademarks of National
Instruments.
Microsoft Windows 98 and Windows NT
are US registered trademerks of Microsoft
Corporation.
Set the overvoltage
protection and enable
the overvoltage
protection circuit
Rotary knob for quick
and analog-like control
of voltage and current
Highly visible vacuum
flourescent display
Tough handle for easy
carriage and unit
prop-up
Selectable dual range
provides flexibility
and convenience
Store and recall up to
five different operating
statuses in nonvolatile storage
locations
Electronic calibration from the front panel
Versatile binding posts
offer flexibility to use
safety test leads, banana
plugs or stripped wires
1 year warranty
protects your
investment
Cooling fan with
automatic speed
control for low
acoustic noise
Built-in GPIB and
RS-232 interfaces
Rear output and
sensing terminals
3
Agilent E3640A – E3649A Programmable DC Power Supply Specifications
Model Number
E3640A
E3641A
E3642A
1
1
0 to 8 V/3 A or
0 to 20 V/1.5 A
0 to 35 V/0.8 A or
0 to 60 V/0.5 A
5.3 kg
5.2 kg
Maximum Power
E3644A
1
1
1
1
0 to 8 V/5 A or
0 to 20 V/2.5 A
0 to 35 V/1.4 A or
0 to 60 V/0.8 A
0 to 8 V/8 A or
0 to 20 V/4 A
0 to 35 V/2.2 A or
0 to 60 V/1.3 A
6.3 kg
6.2 kg
6.6 kg
6.7 kg
30 W
# of Outputs
DC Output Rating
(@ 0 ºC to 40 ºC)
E3643A
Net Weight
50 W
Dimensions (without bumper)
E3645A
80 W
212.6 mm W x 88.5 mm H x 348.3 mm D
Model Number
E3646A
Maximum Power
E3647A
E3648A
60 W
# of Outputs
DC Output Rating
(@ 0 ºC to 40 ºC)
Net Weight
E3649A
100 W
2
2
2
2
Two
0 to 8 V/3 A or
0 to 20 V/1.5 A
Two
0 to 35 V/0.8 A or
0 to 60 V/0.5 A
Two
0 to 8 V/5 A or
0 to 20 V/2.5 A
Two
0 to 35 V/1.4 A or
0 to 60 V/0.8 A
8.0 kg
9.2 kg
9.1 kg
8.2 kg
Dimensions (without bumper)
212.8 mm W x 133.0 mm H x 348.3 mm D
Load and Line Regulation ± (% of output + offset)
Voltage
< 0.01% + 3 mV
Current
< 0.01% + 250 μA
Ripple and Noise (20 Hz to 20 MHz)
Normal Mode Voltage
< 5 mVpp/0.5 mVrms for 8 V/20 V models
< 8 mVpp/1 mVrms for 35 V/60 V models
Normal Mode Current
< 4 mArms
Common Mode Current
< 1.5 μArms
Accuracy1 12 Months (@ 25 ºC ± 5 ºC), ± (% output + offset)
Programming
Voltage
< 0.05% + 10 mV (< 0.1% + 25 mV for output 2 of E3646/47/48/49 A)
Current
< 0.2% + 10 mA
Readback (over GPIB and with respect to actual output)
Voltage
< 0.05% + 5 mV (< 0.1% + 25 mV for output 2 of E3646/47/48/49 A)
Current
< 0.15% + 5 mA (< 0.15% + 10 mA for output 2 of E3646/47/48/49 A)
Meter2 (over front panel with respect to actual output)
Voltage
< 0.05% + 2 counts (<0.1% + 4 counts for output 2)
Current
< 0.15% + 5 mA (<0.15% + 10 mA for output 2)
Resolution
Program
< 5 mV/1 mA
Readback
< 2 mV/1 mA
Meter
Transient Response
10 mV/1 mA
Less than 50 μsec for output to recover to within 15 mV following a change in output current from full load to half
load or vice versa.
Settling Time3
OVP
Accuracy,
± (% output + offset)
Activation Time4
< 90 msec
< 0.5% + 0.5 V
< 1.5 msec, OVP ¥3 V/< 10 msec, OVP < 3 V
1
Accuracy specifications are valid after a 1-hour warm-up with no load and calibration at 25 ºC.
Meter accuracy specification is at minimum 10 mV decimal limited by front panel resolution.
3
Maximum time required for the output voltage to change from 1% to 99% or vice versa following the receipt of VOLTage or APPLy command via direct
GPIB or RS-232 interface.
4
Average time for output to start and drop after an OVP condition occurred.
2
4
Temperature Coefficient per ºC ± (% output + offset)
Voltage
< 0.01% + 3 mV (< 0.02% + 5 mV for output 2 of E3646/47/48/49A)
Current
< 0.02% + 3 mA
Stability, constant load & temperature ± (% output + offset), 8 hrs
Voltage
< 0.02% + 2 mV
Current
< 0.1% + 1 mA
Remote Sensing
Max. voltage drop in each load lead
AC Input
(47 Hz – 63 Hz)
Warranty
Product Regulation
1V
100 Vac ± 10% (Opt 0E9)/115 Vac ± 10% (Std)/230 Vac ± 10% (0E3)
One year for E364xA series power supplies
Three months for standard shipped accessories
Designed to comply with UL3111-1; certified to CSA 22.2 No. 1010.1;
conforms to IEC 1010-1; complies with EMC directive 89/336/EEC (Group 1, Class A)
Ordering Information
Rackmount Kits*
Agilent E364xA Series Power Supplies
E3640A 30-Watt Single Power Supply
E3641A 30-Watt Single Power Supply
E3642A 50-Watt Single Power Supply
E3643A 50-Watt Single Power Supply
E3644A 80-Watt Single Power Supply
E3645A 80-Watt Single Power Supply
E3646A 60-Watt Dual Power Supply
E3647A 60-Watt Dual Power Supply
E3648A 100-Watt Dual Power Supply
E3649A 100-Watt Dual Power Supply
Agilent E3640A/41A/42A/43A/44A/45A
To rackmount two instruments side-by-side
Lock-link Kit (P/N 5061-9694)
Flange Kit (P/N 5063-9212)
To rackmount one or two instruments in a
sliding support shelf
Support Shelf (P/N 5063-9255)
Slide Kit (P/N 1494-0015) required for
support shelf
For a single instrument, also order
Filter Panel (P/N 5002-3999)
Standard Shipped Accessories
Agilent E3646A/47A/48A/49A
To rackmount two instruments side-by-side
Lock-link Kit (P/N 5061-9694)
Flange Kit (P/N 5063-9214)
To rackmount two instruments in a sliding
support shelf
Support Shelf (P/N 5063-9256)
Slide Kit (P/N 1494-0015)
User’s & Service guide, Product
Reference CD, AC power cord
Power Options
Opt. 0E3 230 Vac ± 10%
Opt. 0EM 115 Vac ± 10%
Opt. 0E9 100 Vac ± 10%
Other Options
* Rackmounting with 1CM or lock-link/
flange kit requires
Agilent or customer support rails
Agilent Support Rails-E3663AC
Opt. 1CM Rackmount kit*
– Single Output (P/N 5063-9240)
– Dual Output (P/N 5063-9243)
Opt. 0L2 Extra Manual
Opt. UK6 Commercial calibration with
test result data
E3600A-100 Test lead kit
5
www.agilent.com
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the products and applications you select.
Agilent Direct
www.agilent.com/find/agilentdirect
Quickly choose and use your test
equipment solutions with confidence.
Bhjmfou
Pqfo
Remove all doubt
Our repair and calibration services
will get your equipment back to you,
performing like new, when promised. You will get full value out of
your Agilent equipment throughout its lifetime. Your equipment
will be serviced by Agilent-trained
technicians using the latest factory
calibration procedures, automated
repair diagnostics and genuine parts.
You will always have the utmost
confidence in your measurements.
www.agilent.com/find/open
Agilent Open simplifies the process of connecting and
programming test systems to help engineers design,
validate and manufacture electronic products. Agilent
offers open connectivity for a broad range of systemready instruments, open industry software, PC-standard
I/O and global support, which are combined to more
easily integrate test system development.
is the US registered trademark
of the LXI Consortium.
Agilent offers a wide range of additional expert test and measurement services for your equipment,
including initial start-up assistance
onsite education and training, as
well as design, system integration,
and project management.
For more information on repair and
calibration services, go to
www.agilent.com/find/removealldoubt
Product specifications and descriptions
in this document subject to change
without notice.
For more information on Agilent Technologies’
products, applications or services, please
contact your local Agilent office. The complete list is available at:
www.agilent.com/find/contactus
Phone or Fax
Americas
Canada
Latin America
United States
(877) 894-4414
305 269 7500
(800) 829-4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Thailand
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
1 800 226 008
Europe & Middle East
Austria
Belgium
Denmark
Finland
France
01 36027 71571
32 (0) 2 404 93 40
45 70 13 15 15
358 (0) 10 855 2100
0825 010 700*
*0.125 /minute
07031 464 6333
Germany
1890 924 204
Ireland
972-3-9288-504/544
Israel
39 02 92 60 8484
Italy
31 (0) 20 547 2111
Netherlands
34 (91) 631 3300
Spain
0200-88 22 55
Sweden
0800 80 53 53
Switzerland
44 (0) 118 9276201
United Kingdom
Other European Countries:
www.agilent.com/find/contactus
Revised: October 6, 2008
© Agilent Technologies, Inc. 2009
Printed in USA, July 29, 2009
5968-7355EN
Similar pages