Elpida EBE11UD8ABDA 1gb ddr2 sdram so-dimm Datasheet

PRELIMINARY DATA SHEET
1GB DDR2 SDRAM SO-DIMM
EBE11UD8ABDA (128M words × 64 bits, 2 Ranks)
Features
The EBE11UD8ABDA is 128M words × 64 bits, 2 ranks
DDR2 SDRAM Small Outline Dual In-line Memory
Module, mounting 16 pieces of 512M bits DDR2
SDRAM with sFBGA stacking technology. Read and
write operations are performed at the cross points of
the CK and the /CK. This high-speed data transfer is
realized by the 4 bits prefetch-pipelined architecture.
Data strobe (DQS and /DQS) both for read and write
are available for high speed and reliable data bus
design. By setting extended mode register, the on-chip
Delay Locked Loop (DLL) can be set enable or disable.
This module provides high density mounting without
utilizing surface mount technology.
Decoupling
capacitors are mounted beside each SDRAM on the
module board.
• 200-pin socket type small outline dual in line memory
module (SO-DIMM)
 PCB height: 30.0mm
 Lead pitch: 0.6mm
 Lead-free
• 1.8V power supply
• Data rate: 533Mbps/400Mbps (max.)
• 1.8V (SSTL_18 compatible) I/O
• Double-data-rate architecture: two data transfers per
clock cycle
• Bi-directional, differential data strobe (DQS and
/DQS) is transmitted/received with data, to be used in
capturing data at the receiver
• DQS is edge aligned with data for READs: centeraligned with data for WRITEs
• Differential clock inputs (CK and /CK)
• DLL aligns DQ and DQS transitions with CK
transitions
• Commands entered on each positive CK edge: data
and data mask referenced to both edges of DQS
• Four internal banks for concurrent operation
(Component)
• Data mask (DM) for write data
• Burst lengths: 4, 8
• /CAS Latency (CL): 3, 4, 5
• Auto precharge operation for each burst access
• Auto refresh and self refresh modes
• 7.8µs average periodic refresh interval
• Posted CAS by programmable additive latency for
better command and data bus efficiency
• Off-Chip-Driver Impedance Adjustment and On-DieTermination for better signal quality
• /DQS can be disabled for single-ended Data Strobe
operation.
L
EO
Description
Note: Do not push the components or drop the
modules in order to avoid mechanical defects,
which may result in electrical defects.
t
uc
od
Pr
This Product became EOL in October, 2006.
Document No. E0469E11 (Ver. 1.1)
Date Published February 2004 (K) Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2004
EBE11UD8ABDA
Ordering Information
Data rate
Mbps (max.)
Part number
Component
JEDEC speed bin
(CL-tRCD-tRP)
EBE11UD8ABDA-5C-E 533
DDR2-533 (4-4-4)
EBE11UD8ABDA-4A-E
400
DDR2-400 (3-3-3)
EBE11UD8ABDA-4C-E 400
DDR2-400 (4-4-4)
Package
200-pin SO-DIMM
(lead-free)
Contact
pad
Mounted devices
Gold
512M bits DDR2 SDRAM*
1
Note: 1. Please refer to 512Mb DDR2 datasheet (E0323E) for electrical characteristics.
Pin Configurations
Front side
EO
1 pin
39 pin 41 pin
199 pin
2 pin
40 pin 42 pin
200 pin
Back side
Front side
Back side
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
1
VREF
51
DQS2
2
VSS
52
DM2
3
VSS
53
VSS
4
DQ4
54
VSS
5
DQ0
55
DQ18
6
DQ5
56
DQ22
7
DQ1
57
DQ19
8
VSS
58
DQ23
9
VSS
59
VSS
10
DM0
60
VSS
11
/DQS0
61
DQ24
12
VSS
62
DQ28
13
DQS0
63
DQ25
14
DQ6
64
DQ29
15
VSS
65
VSS
16
DQ7
66
VSS
17
DQ2
67
DM3
18
VSS
68
/DQS3
19
DQ3
69
NC
20
DQ12
70
DQS3
21
VSS
71
VSS
23
DQ8
73
DQ26
25
DQ9
75
DQ27
27
VSS
77
VSS
29
/DQS1
79
CKE0
31
DQS1
81
VDD
33
VSS
83
NC
35
DQ10
85
NC
37
DQ11
87
VDD
39
VSS
89
41
VSS
91
43
DQ16
93
45
DQ17
47
VSS
49
/DQS2
99
L
Pin No.
od
Pr
22
DQ13
72
VSS
24
VSS
74
DQ30
26
DM1
76
DQ31
VSS
78
VSS
30
CK0
80
CKE1
32
/CK0
82
VDD
34
VSS
84
NC
36
DQ14
86
NC
38
DQ15
88
VDD
A12
40
VSS
90
A11
A9
42
VSS
92
A7
A8
44
DQ20
94
A6
95
VDD
46
DQ21
96
97
A5
48
VSS
98
A3
50
NC
100
2
VDD
t
Preliminary Data Sheet E0469E11 (Ver. 1.1)
uc
28
A4
A2
EBE11UD8ABDA
Front side
Back side
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
101
A1
151
DQ42
102
A0
152
DQ46
103
VDD
153
DQ43
104
VDD
154
DQ47
105
A10/AP
155
VSS
106
BA1
156
VSS
107
BA0
157
DQ48
108
/RAS
158
DQ52
109
/WE
159
DQ49
110
/CS0
160
DQ53
111
VDD
161
VSS
112
VDD
162
VSS
113
/CAS
163
NC
114
ODT0
164
CK1
/CS1
165
VSS
116
A13
166
/CK1
117
VDD
167
/DQS6
118
VDD
168
VSS
169
DQS6
120
NC
170
DM6
EO
115
119
ODT1
VSS
171
VSS
122
VSS
172
VSS
123
DQ32
173
DQ50
124
DQ36
174
DQ54
125
DQ33
175
DQ51
126
DQ37
176
DQ55
127
VSS
177
VSS
128
VSS
178
VSS
129
/DQS4
179
DQ56
130
DM4
180
DQ60
131
DQS4
181
DQ57
132
VSS
182
DQ61
133
VSS
183
VSS
134
DQ38
184
VSS
135
DQ34
DM7
136
DQ39
186
/DQS7
L
121
185
137
DQ35
187
VSS
138
VSS
188
DQS7
139
VSS
189
DQ58
140
DQ44
190
VSS
141
DQ40
191
DQ59
142
DQ45
192
DQ62
143
DQ41
193
145
VSS
195
147
DM5
197
149
VSS
199
144
VSS
194
DQ63
146
/DQS5
196
VSS
SCL
148
DQS5
198
SA0
VDDSPD
150
VSS
200
SA1
t
uc
od
Pr
VSS
SDA
Preliminary Data Sheet E0469E11 (Ver. 1.1)
3
EBE11UD8ABDA
Pin Description
Pin name
Function
A0 to A13
Address input
Row address
Column address
A10 (AP)
Auto precharge
BA0, BA1
Bank select address
DQ0 to DQ63
Data input/output
/RAS
Row address strobe command
A0 to A13
A0 to A9
Column address strobe command
/WE
Write enable
/CS0, /CS1
Chip select
CKE0, CKE1
Clock enable
CK0, CK1
Clock input
/CK0, /CK1
Differential clock input
EO
/CAS
DQS0 to DQS7, /DQS0 to /DQS7
Input and output data strobe
DM0 to DM7
Input mask
SCL
Clock input for serial PD
SDA
Data input/output for serial PD
VDD
VDDSPD
VREF
L
SA0, SA1
VSS
NC
Power for internal circuit
Power for serial EEPROM
Input reference voltage
Ground
Pr
ODT0, ODT1
Serial address input
ODT control
No connection
t
uc
od
Preliminary Data Sheet E0469E11 (Ver. 1.1)
4
EBE11UD8ABDA
Serial PD Matrix
Byte No.
0
1
Function described
Number of bytes utilized by module
manufacturer
Total number of bytes in serial PD
device
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Hex value
Comments
1
0
0
0
0
0
0
0
80H
128 bytes
0
0
0
0
1
0
0
0
08H
256 bytes
Memory type
0
0
0
0
1
0
0
0
08H
DDR2 SDRAM
3
Number of row address
0
0
0
0
1
1
1
0
0EH
14
4
Number of column address
0
0
0
0
1
0
1
0
0AH
10
5
Number of DIMM ranks
0
1
1
0
0
0
0
1
61H
2
6
Module data width
0
1
0
0
0
0
0
0
40H
64
7
Module data width continuation
0
0
0
0
0
0
0
0
00H
0
8
Voltage interface level of this assembly 0
0
0
0
0
1
0
1
05H
SSTL 1.8V
9
DDR SDRAM cycle time, CL = 5
-5C
0
0
1
1
1
1
0
1
3DH
3.75ns*
0
1
0
1
0
0
0
0
50H
5.0ns*
1
0
1
0
1
0
0
0
0
50H
0.5ns*
1
0
1
1
0
0
0
0
0
60H
0.6ns*
1
EO
2
-4A, -4C
10
SDRAM access from clock (tAC)
-5C
-4A, -4C
DIMM configuration type
0
0
0
0
0
0
0
0
00H
None.
12
Refresh rate/type
1
0
0
0
0
0
1
0
82H
7.8µs
L
11
13
Primary SDRAM width
0
0
0
0
1
0
0
0
08H
×8
14
Error checking SDRAM width
0
0
0
0
0
0
0
0
00H
None.
Reserved
0
0
0
0
0
0
0
0
00H
0
0
0
0
0
1
1
0
0
0CH
4,8
15
16
18
Pr
17
SDRAM device attributes:
Burst length supported
SDRAM device attributes: Number of
banks on SDRAM device
SDRAM device attributes:
/CAS latency
0
0
0
0
0
1
0
0
04H
4
0
0
1
1
1
0
0
0
38H
3, 4, 5
0
0
0
0
0
0
0
0
00H
0
1
Reserved
20
DIMM type information
0
0
0
0
0
0
1
0
02H
SO-DIMM
21
SDRAM module attributes
0
0
0
0
0
0
0
0
00H
Normal
22
SDRAM device attributes: General
0
0
1
1
0
0
0
0
30H
VDD ± 0.1V
23
Minimum clock cycle time at CL = 4
-5C
0
0
1
1
1
1
0
1
3DH
3.75ns*
0
1
0
1
0
0
0
0
50H
5.0ns*
1
Maximum data access time (tAC) from
clock at CL = 4
0
-5C
1
0
1
0
0
0
0
50H
0.5ns*
1
-4A, -4C
24
25
1
1
0
0
0
0
1
0
1
0
0
1
1
1
1
1
1
Maximum data access time (tAC) from
clock at CL = 3
0
-5C, -4A
1
1
0
0
0
1
1
1
1
1
Minimum clock cycle time at CL = 3
-5C, -4A
-4C
26
-4C
1
Preliminary Data Sheet E0469E11 (Ver. 1.1)
5
0
0
60H
0.6ns*
1
0
0
50H
5.0ns*
1
1
1
FFH
Undefined*
0
0
60H
0.6ns*
1
1
FFH
Undefined*
1
1
1
t
0
1
uc
-4A, -4C
od
19
EBE11UD8ABDA
Byte No.
Function described
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Hex value
Comments
27
Minimum row precharge time (tRP)
-5C, -4A
0
0
1
1
1
1
0
0
3CH
15ns
0
1
0
1
0
0
0
0
50H
20ns
0
0
0
1
1
1
1
0
1EH
7.5ns
0
0
1
1
1
1
0
0
3CH
15ns
-4C
28
29
Minimum row active to row active
delay (tRRD)
Minimum /RAS to /CAS delay (tRCD)
-5C, -4A
-4C
30
31
1
0
1
0
0
0
0
50H
20ns
0
0
1
0
1
1
0
1
2DH
45ns
Module rank density
1
0
0
0
0
0
0
0
80H
512M bytes
Address and command setup time
before clock (tIS)
-5C
0
0
1
0
0
1
0
1
25H
0.25ns*
1
0
0
1
1
0
1
0
1
35H
0.35ns*
1
Address and command hold time after
clock (tIH)
0
-5C
0
1
1
1
0
0
0
38H
0.38ns*
1
0
1
0
0
1
0
0
0
48H
0.48ns*
1
0
0
0
1
0
0
0
0
10H
0.10ns*
1
0
0
0
1
0
1
0
1
15H
0.15ns*
1
0
0
1
0
0
0
1
1
23H
0.23ns*
1
0
0
1
0
1
0
0
0
28H
0.28ns*
1
EO
0
Minimum active to precharge time
(tRAS)
32
-4A, -4C
33
-4A, -4C
34
L
Data input setup time before clock
(tDS)
-5C
-4A, -4C
35
Data input hold time after clock (tDH)
-5C
-4A, -4C
1
Write recovery time (tWR)
0
0
1
1
1
1
0
0
3CH
15ns*
37
Internal write to read command delay
(tWTR)
-5C
0
0
0
1
1
1
1
0
1EH
7.5ns*
0
0
1
0
1
0
0
0
28H
10ns*
-4A , -4C
Pr
36
1
1
Internal read to precharge command
delay (tRTP)
0
0
0
1
1
1
1
0
1EH
7.5ns*
39
Memory analysis probe characteristics 0
0
0
0
0
0
0
0
00H
TBD
40
Extention of Byte 41 and 42
0
0
0
0
0
0
0
0
00H
Undefined
41
Active command period (tRC)
-5C, -4A
0
0
1
1
1
1
0
0
3CH
60ns*
1
0
1
0
0
0
0
0
1
41H
65ns*
1
1
0
1
0
0
1
69H
105ns*
0
0
0
0
0
0
80H
8ns*
-4C
Auto refresh to active/
Auto refresh command cycle (tRFC)
0
1
43
SDRAM tCK cycle max. (tCK max.)
1
0
44
Dout to DQS skew
-5C
0
0
0
1
1
1
0
0
1
0
0
0
0
0
1
0
1
0
0
0
1
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
-4A, -4C
45
Data hold skew (tQHS)
-5C
-4A, -4C
46
PLL relock time
47 to 61
Preliminary Data Sheet E0469E11 (Ver. 1.1)
6
1
1
1
0
1EH
0.30ns*
1
1
1
23H
0.35ns*
1
0
0
28H
0.40ns*
1
0
1
2DH
0.45ns*
1
0
0
00H
Undefined
0
0
00H
t
42
1
uc
od
38
EBE11UD8ABDA
Byte No.
Function described
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Hex value
Comments
62
SPD Revision
0
0
0
1
0
0
0
0
10H
Rev. 1.0
63
Checksum for bytes 0 to 62
-5C
1
1
1
0
0
0
1
0
E2H
-4A
0
1
1
0
0
1
1
0
66H
-4C
1
1
1
0
0
0
0
1
E1H
64 to 65
Manufacturer’s JEDEC ID code
0
1
1
1
1
1
1
1
7FH
Continuation
code
66
Manufacturer’s JEDEC ID code
1
1
1
1
1
1
1
0
FEH
Elpida Memory
67 to 71
Manufacturer’s JEDEC ID code
0
0
0
0
0
0
0
0
00H
72
Manufacturing location
×
×
×
×
×
×
×
×
××
(ASCII-8bit
code)
EO
Module part number
0
1
0
0
0
1
0
1
45H
E
74
Module part number
0
1
0
0
0
0
1
0
42H
B
75
Module part number
0
1
0
0
0
1
0
1
45H
E
76
Module part number
0
0
1
1
0
0
0
1
31H
1
77
Module part number
0
0
1
1
0
0
0
1
31H
1
78
Module part number
0
1
0
1
0
1
0
1
55H
U
79
Module part number
0
1
0
0
0
1
0
0
44H
D
80
Module part number
0
0
1
1
1
0
0
0
38H
8
81
Module part number
0
1
0
0
0
0
0
1
41H
A
L
73
Module part number
0
1
0
0
0
0
1
0
42H
B
83
Module part number
0
1
0
0
0
1
0
0
44H
D
84
Module part number
0
1
0
0
0
0
0
1
41H
A
85
Module part number
0
0
1
0
1
1
0
1
2DH
—
86
Module part number
-5C
0
0
1
1
0
1
0
1
35H
5
0
0
1
1
0
1
0
0
34H
4
87
Module part number
-4A
0
1
0
0
0
0
0
1
41H
A
0
1
0
0
0
0
1
1
43H
C
0
0
-4A, -4C
-5C, -4C
Module part number
89
Module part number
0
1
90
Module part number
0
0
Revision code
0
0
92
Revision code
0
0
93
Manufacturing date
×
×
94
Manufacturing date
×
×
95 to 98
Module serial number
99 to 127
Manufacture specific data
1
0
1
1
0
1
2DH
—
0
0
0
1
0
1
45H
E
1
0
0
0
0
0
20H
(Space)
1
1
0
0
0
0
30H
Initial
1
0
0
0
0
0
20H
(Space)
×
×
×
×
×
×
××
×
×
×
×
Year code
(BCD)
Week code
(BCD)
uc
91
od
88
Pr
82
×
×
××
Note: These specifications are defined based on component specification, not module.
t
Preliminary Data Sheet E0469E11 (Ver. 1.1)
7
EBE11UD8ABDA
Block Diagram
CKE1
ODT1
/CS1
CKE0
ODT0
/CS0
/DQS0
DQS0
DM0
RS2
RS2
RS2
RS2
RS2
RS2
RS1
/DQS /CS ODT CKE
RS1
RS1
DQS
DQS
DM
DM
EO
8
RS1
DQ0 to DQ7
/DQS1
DQS1
DM1
RS1
RS1
RS1
RS1
8
DQ8 to DQ15
DQS2
DM2
RS1
RS1
8
DQ16 to DQ23
DQS3
DM3
RS1
RS1
RS1
RS1
8
DQ24 to DQ31
A0 to A13
/RAS
/CAS
/WE
/DQS /CS ODT CKE
/DQS5
DQS
DQS5
DM
DM
D1
DQ0
to DQ7
DQ0
to DQ7
D9
DQS
DQS
DQS6
DM
DM
D10
DQ0
to DQ7
RS1
/DQS /CS ODT CKE
/DQS7
DQS
DQS7
D3
DQ0
to DQ7
DM7
D11
RS1
RS3
RS1
RS1
RS1
8
DQ56 to DQ63
RS3
RS3
/DQS /CS ODT CKE
/DQS /CS ODT CKE
DQS
DQS
DQ0
to DQ7
CK0
9.1pF
8 loads
9.1pF
8 loads
DQ0
to DQ7
D13
/DQS /CS ODT CKE
DQS
DM
D6
D14
DQ0
to DQ7
DQ0
to DQ7
/DQS /CS ODT CKE
/DQS /CS ODT CKE
DQS
DQS
DM
DQ0
to DQ7
D7
DQ0
to DQ7
D15
Serial PD
SCL
SCL
SA0
A0
SA1
A1
/CK0
DM
DQS
A0 to A13: SDRAMs (D0 to D15)
/WE: SDRAMs (D0 to D15)
D5
/DQS /CS ODT CKE
/RAS: SDRAMs (D0 to D15)
/CAS: SDRAMs (D0 to D15)
RS3
D12
DQ0
to DQ7
DM
RS1
DM
DQ0
to DQ7
BA0 to BA1: SDRAMs (D0 to D15)
RS3
D4
DM
DQ48 to DQ55
DQS
DM
RS1
RS1
8
DQS
DM
RS1
DM6
/DQS /CS ODT CKE
DQ0
to DQ7
RS1
DQ40 to DQ47
/DQS6
DQ0
to DQ7
RS1
8
/DQS /CS ODT CKE
D2
RS1
RS1
DM5
/DQS /CS ODT CKE
DQS
DM
DQ32 to DQ39
DQS
/DQS /CS ODT CKE
od
BA0 to BA1
8
/DQS /CS ODT CKE
DM
RS1
DM4
Pr
/DQS3
RS1
DQS4
DQ0
to DQ7
/DQS /CS ODT CKE
RS1
RS1
D8
L
/DQS2
DQ0
to DQ7
D0
RS1
/DQS4
/DQS /CS ODT CKE
A2
SDA
SDA
U0
WP
Notes :
1. DQ wiring may be changed within a byte.
uc
CK1
2. DQ, DQS, /DQS, ODT, DM, CKE, /CS relationships
/CK1
must be meintained as shown.
VDDSPD
SPD
VREF
SDRAMs (D0 to D15)
VDD
SDRAMs (D0 to D15, VDD and VDDQ)
VSS
SDRAMs (D0 to D15, SPD)
* D0 to D15 : 512M bits DDR2 SDRAM
t
U0 : 2k bits EEPROM
Rs1 : 22Ω
Rs2 : 3.0Ω
Rs3 : 10.0Ω
Preliminary Data Sheet E0469E11 (Ver. 1.1)
8
EBE11UD8ABDA
Electrical Specifications
• All voltages are referenced to VSS (GND).
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
VT
–0.5 to +2.3
V
Supply voltage relative to VSS
VDD
–0.5 to +2.3
V
Short circuit output current
IOS
50
mA
Power dissipation
PD
8
W
Operating case temperature
TC
0 to +85
°C
Storage temperature
Tstg
–55 to +100
°C
Note
1
EO
Note: DDR2 SDRAM component specification.
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
DC Operating Conditions (TC = 0 to +85°C) (DDR2 SDRAM Component Specification)
Parameter
Symbol
min.
typ.
max.
Unit
Notes
Supply voltage
VDD, VDDQ
4
1.8
1.9
V
0
0
0
V
VDDSPD
1.7
—
3.6
V
L
1.7
VSS
VREF
0.49 × VDDQ
0.50 × VDDQ 0.51 × VDDQ
V
1, 2
Termination voltage
VTT
VREF − 0.04
VREF
VREF + 0.04
V
3
DC input logic high
VIH (DC)
VREF + 0.125

VDDQ + 0.3V
V
DC input low
VIL (DC)
−0.3

VREF – 0.125
V
AC input logic high
VIH (AC)
VREF + 0.250


V
AC input low
VIL (AC)


VREF − 0.250
V
Pr
Input reference voltage
t
uc
od
Notes: 1. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically
the value of VREF is expected to be about 0.5 × VDDQ of the transmitting device and VREF are expected
to track variations in VDDQ.
2. Peak to peak AC noise on VREF may not exceed ±2% VREF (DC).
3. VTT of transmitting device must track VREF of receiving device.
4. VDDQ must be equal to VDD.
Preliminary Data Sheet E0469E11 (Ver. 1.1)
9
EBE11UD8ABDA
DC Characteristics 1 (TC = 0 to +85°C, VDD = 1.8V ± 0.1V)
Parameter
Symbol
Grade
max.
Unit
-5C
-4A, -4C
960
824
mA
-5C
-4A, -4C
1400
1240
mA
Operating current
IDD1
(ACT-READ-PRE)
(Another rank is in IDD2P)
-5C
-4A, -4C
1080
944
mA
Operating current
IDD1
(ACT-READ-PRE)
(Another rank is in IDD3N)
-5C
-4A, -4C
1520
1360
mA
-5C
160
-4A, -4C
128
-5C
400
-4A, -4C
320
Operating current
IDD0
(ACT-PRE)
(Another rank is in IDD2P)
Operating current
IDD0
(ACT-PRE)
(Another rank is in IDD3N)
EO
Precharge power-down
standby current
Precharge quiet standby
current
IDD2P
IDD2Q
L
-5C
Idle standby current
-4A, -4C
one bank; IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD); tRCD = tRCD (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data pattern is same as IDD4W
mA
mA
all banks idle;
tCK = tCK (IDD);
CKE is H, /CS is H;
Other control and address bus inputs are STABLE;
Data bus inputs are FLOATING
mA
all banks idle;
tCK = tCK (IDD);
CKE is H, /CS is H;
Other control and address bus inputs are
SWITCHING;
Data bus inputs are SWITCHING
400
all banks open;
Fast PDN Exit
tCK = tCK (IDD);
MRS(12) = 0
CKE is L;
Other control and
address bus inputs are
STABLE;
Slow PDN Exit
Data bus inputs are
MRS(12) = 1
FLOATING
all banks open;
tCK = tCK (IDD), tRAS = tRAS max.(IDD),
tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are
SWITCHING;
Data bus inputs are SWITCHING
Pr
-5C
640
-4A, -4C
560
-5C
400
-4A, -4C
320
-5C
1040
IDD3P-F
Active power-down
standby current
mA
IDD3P-S
mA
IDD3N
od
Active standby current
one bank; tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
all banks idle;
tCK = tCK (IDD);
CKE is L;
Other control and address bus inputs are STABLE;
Data bus inputs are FLOATING
480
IDD2N
Test condition
mA
Operating current
IDD4R
(Burst read operating)
(Another rank is in IDD2P)
-5C
-4A, -4C
1600
1264
Operating current
IDD4R
(Burst read operating)
(Another rank is in IDD3N)
-5C
-4A, -4C
2040
1680
Operating current
IDD4W
(Burst write operating)
(Another rank is in IDD2P)
-5C
-4A, -4C
1600
1264
mA
Operating current
IDD4W
(Burst write operating)
(Another rank is in IDD3N)
-5C
-4A, -4C
2040
1680
mA
mA
mA
Preliminary Data Sheet E0469E11 (Ver. 1.1)
10
all banks open, continuous burst reads, IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRAS = tRAS max.(IDD), tRP = tRP
(IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data pattern is same as IDD4W
all banks open, continuous burst writes;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRAS = tRAS max.(IDD),
tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
t
960
uc
-4A, -4C
EBE11UD8ABDA
Parameter
Symbol
Grade
max.
Unit
Auto-refresh current
IDD5
(Another rank is in IDD2P)
-5C
-4A, -4C
2080
1904
mA
Auto-refresh current
IDD5
(Another rank is in IDD3N)
-5C
-4A, -4C
2520
2320
mA
Self-refresh current
IDD6
96
mA
-5C
-4A, -4C
2640
2464
mA
Operating current
IDD7
(Bank interleaving)
(Another rank is in IDD3N)
-5C
-4A, -4C
3080
2880
mA
EO
Operating current
IDD7
(Bank interleaving)
(Another rank is in IDD2P)
Test condition
tCK = tCK (IDD);
Refresh command at every tRFC (IDD) interval;
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
Self Refresh Mode;
CK and /CK at 0V;
CKE ≤ 0.2V;
Other control and address bus inputs are FLOATING;
Data bus inputs are FLOATING
all bank interleaving reads, IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = tRCD (IDD) −1 × tCK (IDD);
tCK = tCK (IDD), tRC = tRC (IDD), tRRD = tRRD(IDD),
tRCD = 1 × tCK (IDD);
CKE is H, CS is H between valid commands;
Address bus inputs are STABLE during DESELECTs;
Data pattern is same as IDD4W;
Notes: 1.
2.
3.
4.
L
IDD specifications are tested after the device is properly initialized.
Input slew rate is specified by AC Input Test Condition.
IDD parameters are specified with ODT disabled.
Data bus consists of DQ, DM, DQS, /DQS, RDQS, /RDQS, LDQS, /LDQS, UDQS, and /UDQS. IDD
values must be met with all combinations of EMRS bits 10 and 11.
5. Definitions for IDD
L is defined as VIN ≤ VIL (AC) (max.)
H is defined as VIN ≥ VIH (AC) (min.)
STABLE is defined as inputs stable at an H or L level
FLOATING is defined as inputs at VREF = VDDQ/2
SWITCHING is defined as:
inputs changing between H and L every other clock cycle (once per two clocks) for address and control
signals, and inputs changing between H and L every other data transfer (once per clock) for DQ signals
not including masks or strobes.
6. Refer to AC Timing for IDD Test Conditions.
Pr
od
AC Timing for IDD Test Conditions
For purposes of IDD testing, the following parameters are to be utilized.
DDR2-533
DDR2-400
Parameter
4-4-4
3-3-3
CL(IDD)
4
3
tRCD(IDD)
15
15
tRC(IDD)
60
60
tRRD(IDD)
7.5
7.5
4-4-4
Unit
4
tCK
20
ns
65
ns
7.5
ns
3.75
5
5
tRAS(min.)(IDD)
45
45
45
tRAS(max.)(IDD)
70000
70000
70000
tRP(IDD)
15
15
20
tRFC(IDD)
105
105
105
uc
tCK(IDD)
ns
ns
ns
ns
ns
t
Preliminary Data Sheet E0469E11 (Ver. 1.1)
11
EBE11UD8ABDA
DC Characteristics 2 (TC = 0 to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol
Value
Input leakage current
ILI
2
µA
VDD ≥ VIN ≥ VSS
Output leakage current
ILO
5
µA
VDDQ ≥ VOUT ≥ VSS
VTT + 0.603
V
5
VTT − 0.603
V
5
Output timing measurement reference level VOTR
0.5 × VDDQ
V
1
Output minimum sink DC current
IOL
+13.4
mA
3, 4, 5
Output minimum source DC current
IOH
−13.4
mA
2, 4, 5
Minimum required output pull-up under AC
VOH
test load
Maximum required output pull-down under
VOL
AC test load
EO
Notes: 1.
2.
3.
4.
5.
Unit
Notes
The VDDQ of the device under test is referenced.
VDDQ = 1.7V; VOUT = 1.42V.
VDDQ = 1.7V; VOUT = 0.28V.
The DC value of VREF applied to the receiving device is expected to be set to VTT.
After OCD calibration to 18Ω at TC = 25°C, VDD = VDDQ = 1.8V.
DC Characteristics 3 (TC = 0 to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
Parameter
L
(DDR2 SDRAM Component Specification)
Symbol
min.
max.
Unit
Notes
AC differential input voltage
VID (AC)
0.5
VDDQ + 0.6
V
1, 2
AC differential cross point voltage
VIX (AC)
0.5 × VDDQ − 0.175
0.5 × VDDQ + 0.175
V
2
AC differential cross point voltage
VOX (AC)
0.5 × VDDQ − 0.125
0.5 × VDDQ + 0.125
V
3
Pr
od
Notes: 1. VID(AC) specifies the input differential voltage |VTR -VCP| required for switching, where VTR is the true
input signal (such as CK, DQS, LDQS or UDQS) and VCP is the complementary input signal (such as
/CK, /DQS, /LDQS or /UDQS). The minimum value is equal to VIH(AC) − VIL(AC).
2. The typical value of VIX(AC) is expected to be about 0.5 × VDDQ of the transmitting device and VIX(AC)
is expected to track variations in VDDQ . VIX(AC) indicates the voltage at which differential input signals
must cross.
3. The typical value of VOX(AC) is expected to be about 0.5 × VDDQ of the transmitting device and
VOX(AC) is expected to track variations in VDDQ . VOX(AC) indicates the voltage at which differential
output signals must cross.
VDDQ
VTR
Crossing point
VID
VSSQ
Differential Signal Levels*1, 2
t
uc
VIX or VOX
VCP
Preliminary Data Sheet E0469E11 (Ver. 1.1)
12
EBE11UD8ABDA
ODT DC Electrical Characteristics (TC = 0 to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol
min
typ
max
Unit
Note
Rtt effective impedance value for EMRS (A6, A2) = 0, 1; 75 Ω
Rtt1(eff)
60
Rtt effective impedance value for EMRS (A6, A2) = 1, 0; 150 Ω
Rtt2(eff)
120
75
90
Ω
1
150
180
Ω
1
Deviation of VM with respect to VDDQ/2
∆VM
−3.75

+3.75
%
1
Note: 1. Test condition for Rtt measurements.
Measurement Definition for Rtt(eff)
Apply VIH (AC) and VIL (AC) to test pin separately, then measure current I(VIH(AC)) and I(VIL(AC)) respectively.
VIH(AC), and VDDQ values defined in SSTL_18.
EO
Rtt(eff) =
VIH(AC) − VIL(AC)
I(VIH(AC)) − I(VIL(AC))
Measurement Definition for VM
Measure voltage (VM) at test pin (midpoint) with no load.
2 × VM
VDDQ
∆VM =
− 1 × 100%
L
OCD Default Characteristics (TC = 0 to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Output impedance
Pull-up and pull-down mismatch
Output slew rate
Pr
Parameter
min
typ
max
Unit
Notes
12.6
18
23.4
Ω
1
0

4
Ω
1, 2
1.5

4.5
V/ns
3, 4
Pin Capacitance (TA = 25°C, VDD = 1.8V ± 0.1V)
Parameter
uc
od
Notes: 1. Impedance measurement condition for output source DC current: VDDQ = 1.7V; VOUT = 1420mV;
(VOUT−VDDQ)/IOH must be less than 23.4Ω for values of VOUT between VDDQ and VDDQ−280mV.
Impedance measurement condition for output sink DC current: VDDQ = 1.7V; VOUT = 280mV;
VOUT/IOL must be less than 23.4Ω for values of VOUT between 0V and 280mV.
2. Mismatch is absolute value between pull up and pull down, both are measured at same temperature and
voltage.
3. Slew rate measured from VIL(AC) to VIH(AC).
4. The absolute value of the slew rate as measured from DC to DC is equal to or greater than the slew rate
as measured from AC to AC. This is guaranteed by design and characterization.
Pins
max.
Unit
Input capacitance
CI1
Address, /RAS, /CAS, /WE,
/CS, CKE, ODT
TBD
pF
Input capacitance
CI2
CK, /CK
TBD
pF
Data and DQS input/output
capacitance
CO
DQ, DQS, /DQS, DM
TBD
pF
Preliminary Data Sheet E0469E11 (Ver. 1.1)
13
Note
t
Symbol
EBE11UD8ABDA
AC Characteristics (TC = 0 to +85°C , VDD, VDDQ = 1.8V ± 0.1V, VSS = 0V)
(DDR2 SDRAM Component Specification)
Frequency (Mbps)
Parameter
Symbol
-5C
-4A, -4C
533
400
min.
max.
CL
4
5
Active to read or write command delay
tRCD
15

Precharge command period
tRP
15

Active to active/auto refresh command
time
tRC
60

DQ output access time from CK, /CK
tAC
−500
+500
EO
/CAS latency
min.
max.
Unit
3 (-4A)
4 (-4C)
15 (-4A)
20 (-4C)
15 (-4A)
20 (-4C)
60 (-4A)
65 (-4C)
5 (-4A)
5 (-4C)
tCK

ns

ns

ns
+600
ps
−600
Notes
tDQSCK −450
+450
−500
+500
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min.
(tCL, tCH)

min.
(tCL, tCH)

ps
Clock cycle time
tCK
3750
8000
5000
8000
ps
DQ and DM input hold time
tDH
225

275

ps
5
DQ and DM input setup time
tDS
100

150

ps
4
tIPW
0.6

0.6

tCK
tDIPW
0.35

0.35

tCK
tHZ

tAC max.

tAC max.
ps
tLZ
tAC min.
tAC max.
tAC min.
tAC max.
ps
tDQSQ

300

350
ps
tQHS

400

450
ps
L
DQS output access time from CK, /CK
DQ hold skew factor
Pr
Control and Address input pulse width
for each input
DQ and DM input pulse width for each
input
Data-out high-impedance time from
CK,/CK
Data-out low-impedance time from
CK,/CK
DQS-DQ skew for DQS and associated
DQ signals
tHP – tQHS

tHP – tQHS

ps
tDQSS
WL − 0.25
WL + 0.25
WL − 0.25
WL + 0.25
tCK
DQS input high pulse width
tDQSH
0.35

0.35

tCK
DQS input low pulse width
tDQSL
0.35

0.35

tCK
DQS falling edge to CK setup time
tDSS
0.2

0.2

tCK

0.2

tCK

2

tCK

tCK
0.6
tCK

tCK

ps
5

ps
4
1.1
tCK
DQS falling edge hold time from CK
tDSH
0.2
Mode register set command cycle time
tMRD
2
Write preamble setup time
tWPRES 0

0
Write postamble
tWPST
0.4
0.6
0.4
Write preamble
tWPRE
0.25

0.25
Address and control input hold time
tIH
375

475
Address and control input setup time
tIS
250

350
Read preamble
tRPRE
0.9
1.1
0.9
Read postamble
tRPST
0.4
0.6
0.4
0.6
Active to precharge command
tRAS
45
70000
45
70000
Active to auto-precharge delay
tRAP
tRCD min.

tRCD min.

Preliminary Data Sheet E0469E11 (Ver. 1.1)
14
t
uc
od
tQH
Write command to first DQS latching
transition
DQ/DQS output hold time from DQS
tCK
ns
ns
EBE11UD8ABDA
Frequency (Mbps)
-5C
-4A, -4C
533
400
Parameter
Symbol
min.
max.
min.
max.
Unit
Active bank A to active bank B
command period
tRRD
7.5

7.5

ns
Write recovery time
Notes
tWR
15

15

ns
Auto precharge write recovery +
precharge time
tDAL
(tWR/tCK)+
(tRP/tCK)

(tWR/tCK)+
(tRP/tCK)

tCK
Internal write to read command delay
tWTR
7.5

10

ns
Internal read to precharge command
delay
tRTP
7.5

7.5

ns
tRFC + 10

tRFC + 10

ns
tXSRD
200

200

tCK
tXP
2

2

tCK
tXARD
2

2

tCK
3
tXARDS 6 − AL

6 − AL

tCK
2, 3
tCKE
3

3

tCK
Exit self refresh to a non-read command tXSNR
EO
Exit self refresh to a read command
Exit precharge power down to any nonread command
Exit active power down to read
command
Exit active power down to read
command
(slow exit/low power mode)
CKE minimum pulse width (high and low
pulse width)
L
Output impedance test driver delay
tOIT
0
12
0
12
ns
Auto refresh to active/auto refresh
command time
tRFC
105

105

ns
Average periodic refresh interval
tREFI

7.8

7.8
µs
Minimum time clocks remains ON after
CKE asynchronously drops low
tDELAY tIS + tCK + tIH 
tIS + tCK + tIH 
1
ns
Pr
Notes: 1.
2.
3.
4.
od
For each of the terms above, if not already an integer, round to the next higher integer.
AL: Additive Latency.
MRS A12 bit defines which active power down exit timing to be applied.
The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIH(AC) level for a rising signal and VIL(AC) for a falling signal applied to the device under test.
5. The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIH(DC) level for a rising signal and VIL(DC) for a falling signal applied to the device under test.
CK
DQS
/DQS
/CK
tDS
tDH
tDS
tDH
tIS
tIH
tIS
tIH
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
uc
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
Input Waveform Timing 1 (tDS, tDH)
Input Waveform Timing 2 (tIS, tIH)
t
Preliminary Data Sheet E0469E11 (Ver. 1.1)
15
EBE11UD8ABDA
ODT AC Electrical Characteristics (DDR2 SDRAM Component Specification)
Parameter
Symbol
min
max
Unit
ODT turn-on delay
tAOND
2
2
tCK
ODT turn-on
tAON
tAC(min)
tAC(max) + 1000
ps
ODT turn-on (power down mode)
tAONPD
tAC(min) + 2000
2tCK + tAC(max) + 1000
ps
ODT turn-off delay
tAOFD
2.5
2.5
tCK
ODT turn-off
tAOF
tAC(min)
tAC(max) + 600
ps
ODT turn-off (power down mode)
tAOFPD
tAC(min) + 2000
2.5tCK + tAC(max) + 1000
ns
ODT to power down entry latency
tANPD
3
3
tCK
ODT power down exit latency
tAXPD
8
8
tCK
Notes
1
2
EO
Notes: 1. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on.
ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND.
2. ODT turn off time min is when the device starts to turn off ODT resistance.
ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
AC Input Test Conditions
Symbol
Value
Unit
Notes
Input reference voltage
VREF
0.5 × VDDQ
V
1
Input signal maximum peak to peak swing
VSWING(max.)
1.0
V
1
Input signal maximum slew rate
SLEW
1.0
V/ns
2, 3
L
Parameter
Pr
Notes: 1. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the
device under test.
2. The input signal minimum slew rate is to be maintained over the range from VIL(DC) (max.) to VIH(AC)
(min.) for rising edges and the range from VIH(DC) (min.) to VIL(AC) (max.) for falling edges as shown in
the below figure.
3. AC timings are referenced with input waveforms switching from VIL(AC) to VIH(AC) on the positive
transitions and VIH(AC) to VIL(AC) on the negative transitions.
Start of rising edge input timing
Start of falling edge input timing
VDDQ
VIH (AC)(min.)
od
VIH (DC)(min.)
VSWING(max.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
Falling slew =
VSS
∆TR
∆TF
VIH (DC)(min.) − VIL (AC)(max.)
Rising slew =
VIH (AC) min. − VIL (DC)(max.)
AC Input Test Signal Wave forms
Measurement point
DQ
VTT
Output Load
Preliminary Data Sheet E0469E11 (Ver. 1.1)
16
t
RT =25 Ω
∆TR
uc
∆TF
EBE11UD8ABDA
Pin Functions
CK, /CK (input pin)
The CK and the /CK are the master clock inputs. All inputs except DMs, DQSs and DQs are referred to the cross
point of the CK rising edge and the VREF level. When a read operation, DQSs and DQs are referred to the cross
point of the CK and the /CK. When a write operation, DMs and DQs are referred to the cross point of the DQS and
the VREF level. DQSs for write operation are referred to the cross point of the CK and the /CK.
/CS (input pin)
When /CS is low, commands and data can be input. When /CS is high, all inputs are ignored. However, internal
operations (bank active, burst operations, etc.) are held.
EO
/RAS, /CAS, and /WE (input pins)
These pins define operating commands (read, write, etc.) depending on the combinations of their voltage levels.
See "Command operation".
A0 to A13 (input pins)
Row address (AX0 to AX13) is determined by the A0 to the A13 level at the cross point of the CK rising edge and the
VREF level in a bank active command cycle. Column address (AY0 to AY9) is loaded via the A0 to the A9 at the
cross point of the CK rising edge and the VREF level in a read or a write command cycle. This column address
becomes the starting address of a burst operation.
L
A10 (AP) (input pin)
A10 defines the precharge mode when a precharge command, a read command or a write command is issued. If
A10 = high when a precharge command is issued, all banks are precharged. If A10 = low when a precharge
command is issued, only the bank that is selected by BA1, BA0 is precharged. If A10 = high when read or write
command, auto-precharge function is enabled. While A10 = low, auto-precharge function is disabled.
[Bank Select Signal Table]
Bank 0
BA0
BA1
L
L
H
Bank 2
L
Bank 3
H
Remark: H: VIH. L: VIL.
L
od
Bank 1
Pr
BA0 and BA1 (input pins)
BA0, BA1 are bank select signals (BA). The memory array is divided into bank 0, bank 1, bank 2 and bank 3. (See
Bank Select Signal Table)
H
H
DQ (input and output pins)
Data are input to and output from these pins.
DQS and /DQS (input and output pin)
DQS and /DQS provide the read data strobes (as output) and the write data strobes (as input).
Preliminary Data Sheet E0469E11 (Ver. 1.1)
17
t
uc
CKE (input pin)
CKE controls power down and self-refresh. The power down and the self-refresh commands are entered when the
CKE is driven low and exited when it resumes to high.
The CKE level must be kept for 1 CK cycle at least, that is, if CKE changes at the cross point of the CK rising edge
and the VREF level with proper setup time tIS, at the next CK rising edge CKE level must be kept with proper hold
time tIH.
EBE11UD8ABDA
DM (input pins): DM is the reference signal of the data input mask function. DMs are sampled at the cross point of
DQS and /DQS.
VDD (power supply pins)
1.8V is applied. (VDD is for the internal circuit.)
VDDSPD (power supply pin)
1.8V is applied (For serial EEPROM).
VSS (power supply pin)
Ground is connected.
EO
Detailed Operation Part and Timing Waveforms
Refer to the EDE5104ABSE, EDE5108ABSE, EDE5116ABSE datasheet (E0323E).
L
t
uc
od
Pr
Preliminary Data Sheet E0469E11 (Ver. 1.1)
18
EBE11UD8ABDA
Physical Outline
Unit: mm
Front side
11.55
2.00 Min
17.55
3.80 Max
(DATUM -A-)
4x Full R
1
EO
199
6.00
4.00 Min
Component area
(Front)
2.15
A
B
11.40
2.45
47.40
D
1.00 ± 0.10
67.60
Back side
63.60
2.45
2.15
30.00
20.00
4.00
2
L
200
C
Component area
(Back)
Pr
(DATUM -A-)
Detail B
0.51 Max
0.45 ± 0.03
2.70
4.20
1.00 ± 0.10
Detail D
uc
Detail C
FULL R
od
2.55 Min
0.60
4.00 ± 0.10
Detail A
Contact pad
0.25 Max
0.51 Max
4.20
2.40
t
ECA-TS2-0106-01
Preliminary Data Sheet E0469E11 (Ver. 1.1)
19
EBE11UD8ABDA
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
EO
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
L
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
3
od
Pr
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
STATUS BEFORE INITIALIZATION OF MOS DEVICES
uc
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
t
Preliminary Data Sheet E0469E11 (Ver. 1.1)
20
EBE11UD8ABDA
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
EO
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
L
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
M01E0107
t
uc
od
Pr
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
Preliminary Data Sheet E0469E11 (Ver. 1.1)
21
Similar pages