WJ ECG001F Ingap hbt gain block Datasheet

ECG001F
InGaP HBT Gain Block
Product Features
Product Description
DC – 6 GHz
+12.5 dBm P1dB at 1 GHz
+25 dBm OIP3 at 1 GHz
22 dB Gain at 1 GHz
3.4 dB Noise Figure
Available in lead-free / green
SOT-363 package
• Internally matched to 50 Ω
The ECG001F is a general-purpose buffer amplifier that
offers high dynamic range in a low-cost surface-mount
package. At 1000 MHz, the ECG001F typically provides
22 dB of gain, +25 dBm Output IP3, and +12.5 dBm P1dB.
•
•
•
•
•
•
Applications
•
•
•
•
•
The ECG001F consists of Darlington pair amplifiers using
the high reliability InGaP/GaAs HBT process technology
and only requires DC-blocking capacitors, a bias resistor,
and an inductive RF choke for operation. The device is
ideal for wireless applications and is available in a lowcost, surface-mountable lead-free/green/RoHS-compliant
SOT-363 package. All devices are 100% RF and DC
tested.
GND
1
6
RF OUT
GND
2
5
GND
RF IN
3
4
GND
Function
Input
Output/Bias
Ground
Pin No.
3
6
1, 2, 4, 5
The broadband MMIC amplifier can be directly applied to
various current and next generation wireless technologies
such as GPRS, GSM, CDMA, and W-CDMA. In addition,
the ECG001F will work for other various applications
within the DC to 6 GHz frequency range such as CATV
and mobile wireless.
Mobile Infrastructure
CATV / FTTX
W-LAN / ISM
RFID
WiMAX / WiBro
Specifications (1)
Parameter
Functional Diagram
Typical Performance (1)
Units
Min
MHz
MHz
dB
dBm
dBm
MHz
dB
dB
dB
dBm
dB
V
mA
DC
Operational Bandwidth
Test Frequency
Gain
Output P1dB
Output IP3 (2)
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Noise Figure
Device Voltage
Device Current
19.2
3.0
Typ
1000
22.2
+12.5
+25
2000
20.7
35
18
+12.5
3.4
3.4
30
Max
Parameter
Units
6000
Frequency
S21
S11
S22
Output P1dB
Output IP3 (2)
Noise Figure
MHz
dB
dB
dB
dBm
dBm
dB
21.8
Typical
500
22.6
-46
-29
+12
+23
3.4
900
22.4
-42
-24
+12.5
+25
3.4
1900
20.9
-35
-18
+12.5
+26
3.4
2140
20.6
-29
-17
+12.5
+26
3.4
3.8
1. Test conditions unless otherwise noted: 25 ºC, Supply Voltage = +5 V, Rbias = 51 Ω, 50 Ω System.
Absolute Maximum Rating
Parameter
Rating
Operating Case Temperature
Storage Temperature
Device Current
RF Input Power (continuous)
Junction Temperature
-40 to +85 °C
-55 to +150 °C
150 mA
+12 dBm
+250 °C
Ordering Information
Part No.
Description
ECG001F-G
InGaP HBT Gain Block
ECG001F-PCB
700 – 2400 MHz Fully Assembled Eval. Board
(lead-free/green/RoHS-compliant SOT-363 package)
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
Page 1 of 5 April 2007
ECG001F
InGaP HBT Gain Block
Typical Device RF Performance
Supply Bias = +5 V, Rbias = 51 Ω, Icc = 30 mA
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
MHz
dB
dB
dB
dBm
dBm
dB
100
22.8
-48
-34
+11.6
+23.6
3.4
500
22.6
-46
-29
+11.6
+23.5
3.4
900
22.4
-42
-24
+12.6
+24.8
3.4
1900
20.9
-35
-18
+12.6
+26
3.4
2140
20.6
-29
-17
+12.6
+25.6
3.4
2400
20.2
-28
-16
+12.8
+25.4
3.4
3500
18.6
-22
-13
+12.2
+23
5800
15.5
-14
-8
+11
1. Test conditions: T = 25º C, Supply Voltage = +5 V, Device Voltage = +3.4 V, Rbias = 51 Ω, Icc = 30 mA typical, 50 Ω System.
2. 3OIP measured with two tones at an output power of -1 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit.
Icc vs. Vde
Return Loss
0
G a in (dB )
24
D B (|S (2 ,1 )|)
80
S11, S22 (dB)
20
18
16
Icc (mA)
-10
22
F requency
100
-20
-30
S11
14
0
1
2
3
F requency (G H z)
4
5
40
20
S22
-40
6
60
0
0
1
2
3
4
5
6
3.2
3.3
Frequency (GHz)
Noise Figure vs. Frequency
OIP3 vs. Frequency
28
P1dB (dBm)
NF (dB)
OIP3 (dBm)
16
14
3
12
2
10
22
1
+25C
20
500
3.6
P1dB vs. Frequency
4
24
3.5
18
5
26
3.4
Vde (V)
-40C
8
+85C
+25C
0
1000
1500
2000
Frequency (MHz)
2500
3000
50 0
10 00
15 00
20 00
Frequency (MHz)
25 00
30 00
6
500
1000
-40C
1500
2000
Frequency (MHz)
+85C
2500
3000
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
Page 2 of 5 April 2007
ECG001F
InGaP HBT Gain Block
Recommended Application Circuit
Vcc
Icc = 30 mA
R4
Bias
Resistor
C4
Bypass
Capacitor
C3
0.018 µF
L1
RF Choke
RF IN
RF OUT
ECG001F
C2
Blocking
Capacitor
C1
Blocking
Capacitor
ECG001F-PCB
Reference
Designator
L1
C1, C2, C4
50
820 nH
.018 µF
Recommended Component Values
Frequency (MHz)
500
900
1900
2200
220 nH
68 nH
27 nH
22 nH
1000 pF
100 pF
68 pF
68 pF
2500
18 nH
56 pF
Recommended Bias Resistor Values
Supply
R1 value
Size
Voltage
5V
53.3 ohms
0805
6V
86.7 ohms
0805
8V
153 ohms
1210
9V
187 ohms
1210
10 V
220 ohms
2010
12 V
287 ohms
2010
3500
15 nH
39 pF
1. The proper values for the components are dependent upon the intended frequency of operation.
2. The following values are contained on the evaluation board to achieve optimal broadband performance:
Ref. Desig.
L1
C1, C2
C3
C4
R4
Value / Type
39 nH wirewound inductor
56 pF chip capacitor
0.018 µF chip capacitor
Do Not Place
51Ω 1% tolerance
Size
0603
0603
0603
The proper value for R1 is dependent upon the supply
voltage and allows for bias stability over temperature.
WJ recommends a minimum supply bias of +5 V. A
1% tolerance resistor is recommended.
0805
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
Page 3 of 5 April 2007
ECG001F
InGaP HBT Gain Block
ECG001F-G Mechanical Information
This package is lead-free/Green/RoHS-compliant. The plating material on the leads is annealed matte tin over copper. It is compatible with
both lead-free (maximum 260 °C reflow temperature) and leaded (maximum 245 °C reflow temperature) soldering processes.
Outline Drawing
Product Marking
The component will be marked with a two-digit
numeric lot code (shown as “XX”) followed
with a “4” designator on the top surface of the
package. The obsolete tin-lead package is
marked with a two-digit numeric lot code
followed with a “0” designator; it may also
have been marked with a “00” designator
followed by a letter lot code.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
ESD Rating:
Value:
Test:
Standard:
Class 1A
Passes between 250 and 500V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
MSL Rating: Level 3 at +260 °C convection reflow
Standard:
JEDEC Standard J-STD-020
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance of this
device. Vias should use a .35mm (#80 / .0135”) diameter drill and
have a final plated thru diameter of .25 mm (.010”).
2. Add as much copper as possible to inner and outer layers near the
part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the board to a
heatsink. Ensure that the ground / thermal via region contacts the
heatsink.
4. Do not put solder mask on the backside of the PC board in the
region where the board contacts the heatsink.
5. RF trace width depends upon the PC board material and
construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are in degrees.
Land Pattern
Thermal Specifications
Parameter
Rating
Operating Case Temperature
Thermal Resistance, Rth
-40 to +85 °C
270 °C/W
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
Page 4 of 5 April 2007
ECG001F
InGaP HBT Gain Block
Typical Device S-Parameters
S-Parameters (Vdevice = +3.4 V, ICC = 30 mA, T = 25°C, calibrated to device leads)
Freq (MHz)
50
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
-33.58
-24.53
-32.76
-28.56
-25.13
-28.01
-28.65
-28.35
-25.99
-22.91
-19.69
-17.30
-15.88
15.96
12.09
32.44
153.22
172.50
-117.92
-133.85
-142.02
-171.80
160.22
153.85
152.52
144.43
22.85
22.63
22.20
21.54
20.74
20.11
19.33
18.59
17.77
17.05
16.39
15.78
15.21
178.01
162.01
144.90
129.42
114.94
103.13
91.28
79.59
68.13
57.38
48.12
39.49
30.49
-24.47
-24.14
-23.99
-23.56
-23.12
-22.71
-22.14
-21.68
-20.88
-20.50
-20.03
-19.55
-19.14
S12 (ang)
-1.35
1.89
4.76
7.59
9.11
7.41
7.37
4.16
2.49
2.47
-0.55
-5.36
-6.76
S22 (dB)
S22 (ang)
-28.60
-22.29
-25.75
-20.80
-17.59
-20.44
-18.13
-16.41
-14.29
-12.47
-11.36
-11.30
-11.31
3.58
-35.35
-100.14
-165.24
175.89
169.69
154.41
140.24
124.73
116.41
113.60
114.22
113.24
Device S-parameters are available for download off of the website at: http://www.wj.com
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
Page 5 of 5 April 2007
Similar pages