Intel EE80C196MC Industrial motor control microcontroller Datasheet

8XC196MC
INDUSTRIAL MOTOR CONTROL
MICROCONTROLLER
87C196MC 16 Kbytes of On-Chip OTPROM*
87C196MC, ROM 16 Kbytes of On-Chip Factory-Programmed OTPROM
80C196MC ROMless
Y
High-Performance CHMOS 16-Bit CPU
Y
16 Kbytes of On-Chip OTPROM/
Factory-Programmed OTPROM
Y
488 bytes of On-Chip Register RAM
Y
Register to Register Architecture
Y
Up to 53 I/O Lines
Y
Peripheral Transaction Server (PTS)
with 11 Prioritized Sources
Y
Y
Event Processor Array (EPA)
Ð 4 High Speed Capture/Compare
Modules
Ð 4 High Speed Compare Modules
Y
Two 16-Bit Timers with Quadrature
Decoder Input
Y
3-Phase Complementary Waveform
Generator
Y
13 Channel 8/10-Bit A/D with Sample/
Hold with Zero Offset Adjustment H/W
Y
14 Prioritized Interrupt Sources
Y
Flexible 8-/16-Bit External Bus
Y
1.75 ms 16 x 16 Multiply
Y
3 ms 32/16 Divide
Y
Idle and Power Down Modes
Extended Temperature Standard
The 8XC196MC is a 16-bit microcontroller designed primarily to control 3 phase AC induction and DC brushless motors. The 8XC196MC is based on Intel’s MCSÉ 96 16-bit microcontroller architecture and is manufactured with Intel’s CHMOS process.
The 8XC196MC has a three phase waveform generator specifically designed for use in ‘‘Inverter’’ motor
control applications. This peripheral allows for pulse width modulation, three phase sine wave generation with
minimal CPU intervention. It generates 3 complementary non-overlapping PWM pulses with resolutions of
0.125 ms (edge trigger) or 0.250 ms (centered).
The 8XC196MC has 16 Kbytes on-chip OTPROM/ROM and 488 bytes of on-chip RAM. It is available in three
packages; PLCC (84-L), SDIP (64-L) and EIAJ/QFP (80-L).
Note that the 64-L SDIP package does not include P1.4, P2.7, P5.1 and the CLKOUT pins.
Operational characteristics are guaranteed over the temperature range of b 40§ C to a 85§ C.
The 87C196MC contains 16 Kbytes on-chip OTPROM. The 83C196MC contains 16 Kbytes on-chip ROM. All
references to the 80C196MC also refers to the 83C196MC and 87C196MC unless noted.
*OTPROM (One Time Programmable Read Only Memory) is the same as EPROM but it comes in an unwindowed package
and cannot be erased. It is user programmable.
*Other brands and names are the property of their respective owners.
Information in this document is provided in connection with Intel products. Intel assumes no liability whatsoever, including infringement of any patent or
copyright, for sale and use of Intel products except as provided in Intel’s Terms and Conditions of Sale for such products. Intel retains the right to make
changes to these specifications at any time, without notice. Microcomputer Products may have minor variations to this specification known as errata.
COPYRIGHT © INTEL CORPORATION, 1995
April 1994
Order Number: 270946-005
8XC196MC
270946 – 1
NOTE:
Connections between the standard I/O ports and the bus are not shown.
Figure 1. 87C196MC Block Diagram
2
8XC196MC
8XC196MC Memory Map
PROCESS INFORMATION
This device is manufactured on PX29.5, a CHMOS
III-E process. Additional process and reliability information is available in the Intel® Quality
System Handbook.
270946 – 16
EXAMPLE: N87C196MC is 84-Lead PLCC OTPROM,
16 MHz.
For complete package dimensional data, refer to the
Intel Packaging Handbook (Order Number 240800).
NOTE:
1. EPROMs are available as One Time Programmable
(OTPROM) only.
Figure 3. The 8XC196MC Family Nomenclature
Thermal Characteristics
Package
Type
ija
ijc
PLCC
35§ C/W
13§ C/W
QFP
56§ C/W
12§ C/W
SDIP
TBD
TBD
All thermal impedance data is approximate for static air
conditions at 1W of power dissipation. Values will change
depending on operation conditions and application. See
the Intel Packaging Handbook (order number 240800) for a
description of Intel’s thermal impedance test methodology.
Description
External Memory or I/O
Address
0FFFFH
06000H
Internal ROM/EPROM or External
Memory (Determined by EA)
5FFFH
2080H
Reserved. Must contain FFH.
(Note 5)
207FH
205EH
PTS Vectors
205DH
2040H
Upper Interrupt Vectors
203FH
2030H
ROM/EPROM Security Key
202FH
2020H
Reserved. Must contain FFH.
(Note 5)
201FH
201CH
Reserved. Must Contain 20H
(Note 5)
201BH
CCB1
201AH
Reserved. Must Contain 20H
(Note 5)
2019H
CCB0
2018H
Reserved. Must contain FFH.
(Note 5)
2017H
2014H
Lower Interrupt Vectors
2013H
2000H
SFR’s
1FFFH
1F00H
External Memory
1EFFH
0200H
488 Bytes Register RAM (Note 1)
01FFH
0018H
CPU SFR’s (Notes 1, 3)
0017H
0000H
NOTES:
1. Code executed in locations 0000H to 03FFH will be
forced external.
2. Reserved memory locations must contain 0FFH unless
noted.
3. Reserved SFR bit locations must contain 0.
4. Refer to 8XC196KC for SFR descriptions.
5. WARNING: Reserved memory locations must not be
written or read. The contents and/or function of these locations may change with future revisions of the device.
Therefore, a program that relies on one or more of these
locations may not function properly.
3
8XC196MC
270946 – 2
NOTE:
*The pin sequence is correct.
The 64-Lead SDIP package does not include the following pins: P1.4/ACH12, P2.7/COMPARE3, P5.1/INST,
CLKOUT.
Figure 2. 64-Lead Shrink DIP (SDIP) Package
4
8XC196MC
270946 – 3
NOTE:
NC means No Connect. Do not connect these pins.
Figure 3. 84-Lead PLCC Package
5
8XC196MC
270946 – 4
NOTE:
NC means No Connect. Do not connect these pins.
Figure 4. 80-Lead Shrink EIAJQFP (Quad Flat Pack)
6
8XC196MC
PIN DESCRIPTIONS
(Alphabetically Ordered)
Symbol
ACH0–ACH12
(P0.0–P0.7, P1.0–P1.4)
ANGND
ALE/ADV(P5.0)
BHE/WRH (P5.5)
BUSWIDTH (P5.7)
CAPCOMP0–CAPCOMP3
(P2.0–P2.3)
CLKOUT
COMPARE0–COMPARE3
(P2.4–P2.7)
EA
EXTINT
INST (P5.1)
NMI
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
Function
Analog inputs to the on-chip A/D converter. ACH0 – 7 share the input pins
with P0.0–7 and ACH8 – 12 share pins with P1.0 – 4. If the A/D is not used,
the port pins can be used as standard input ports.
Reference ground for the A/D converter. Must be held at nominally the
same potential as VSS.
Address Latch Enable or Address Valid output, as selected by CCR. Both
options allow a latch to demultiplex the address/data bus on the signal’s
falling edge. When the pin is ADV, it goes inactive (high) at the end of the
bus cycle. ALE/ADV is active only during external memory accesses. Can be
used as standard I/O when not used as ALE/ADV.
Byte High Enable or Write High output, as selected by the CCR. BHE will go
low for external writes to the high byte of the data bus. WRH will go low for
external writes where an odd byte is being written. BHE/WRH is activated
only during external memory writes.
Input for bus width selection. If CCR bits 1 and 2 e 1, this pin dynamically
controls the bus width of the bus cycle in progress. If BUSWIDTH is low, an
8-bit cycle occurs. If it is high, a 16-bit cycle occurs. This pin can be used as
standard I/O when not used as BUSWIDTH.
The EPA Capture/Compare pins. These pins share P2.0 – P2.3. If not used
for the EPA, they can be configured as standard I/O pins.
Output of the internal clock generator. The frequency is (/2 of the oscillator
frequency. It has a 50% duty cycle.
The EPA Compare pins. These pins share P2.4 – P2.7. If not used for the
EPA, they can be configured as standard I/O pins.
External Access enable pin. EA e 0 causes all memory accesses to be
external to the chip. EA e 1 causes memory accesses from location 2000H
to 5FFFH to be from the on-chip OTPROM/QROM. EA e 12.5V causes
execution to begin in the programming mode. EA is latched at reset.
A programmable input on this pin causes a maskable interrupt vector
through memory location 203CH. The input may be selected to be a
positive/negative edge or a high/low level using WGÐPROTECT (1FCEH).
INST is high during the instruction fetch from the external memory and
throughout the bus cycle. It is low otherwise. This pin can be configured as
standard I/O if not used as INST.
A positive transition on this pin causes a non-maskable interrupt which
vectors to memory location 203EH. If not used, it should be tied to VSS. May
be used by Intel Evaluation boards.
8-bit high impedance input-only port. Also used as A/D converter inputs.
Port0 pins should not be left floating. These pins also used to select
programming modes in the OTPROM devices.
5-bit high impedance input-only port. P1.0 – P1.4 are also used as A/D
converter inputs. In addition, P1.2 and P1.3 can be used as Timer 1 clock
input and direction select respectively.
8-bit bidirectional I/O port. All of the Port2 pins are shared with the EPA I/O
pins (CAPCOMP0 – 3 and COMPARE0 – 3).
8-bit bidirectional I/O ports with open drain outputs. These pins are shared
with the multiplexed address/data bus which uses strong internal pullups.
8-bit bidirectional I/O port. 7 of the pins are shared with bus control signals
(ALE, INST, WR, RD, BHE, READY, BUSWIDTH). Can be used as standard
I/O.
7
8XC196MC
PIN DESCRIPTIONS
Symbol
PORT6
PWM0, PWM1
(P6.6, P6.7)
RD (P5.3)
READY (P5.6)
RESET
T1CLK
(P1.2)
T1DIR
(P1.3)
VPP
WG1–WG3/WG1 –WG3
(P6.0–P6.5)
WR/WRL (P5.2)
XTAL1
XTAL2
PMODE
(P0.4–7)
PACT
(P2.5)
PALE
(P2.1)
PROG
(P2.2)
PVER
(P2.0)
CPVER
(P2.6)
AINC
(P2.4)
8
(Alphabetically Ordered) (Continued)
Function
8-bit output port. P6.6 and P6.7 output PWM, the others are used as the Wave
Form Generator outputs. Can be used as standard output ports.
Programmable duty cycle, Programmable frequency Pulse Width Modulator
pins. The duty cycle has a resolution of 256 steps, and the frequency can vary
from 122 Hz to 31 KHz (16 MHz input clock). Pins may be configured as
standard output if PWM is not used.
Read signal output to external memory. RD is low only during external memory
reads. Can be used as standard I/O when not used as RD.
Ready input to lengthen external memory cycles. If READY e 0, the memory
controller inserts wait states until the next positive transition of CLKOUT
occurs with READY e 1. Can be used as standard I/O when not used as
READY.
Reset input to and open-drain output from the chip. Held low for at least 16
state times to reset the chip. Input high for normal operation. RESET has an
Ohmic internal pullup resistor.
Timer 0 Clock input. This pin has two other alternate functions: ACH10 and
P1.2.
Timer 0 Direction input. This pin has two other alternate functions: ACH11 and
P1.3.
The programming voltage is applied to this pin. It is also the timing pin for the
return from Power Down circuit. Connect this pin with a 1 mF capacitor to VSS
and a 1 MX resistor to VCC. If the Power Down feature is not used, connect
the pin to VCC.
3 phase output signals and their complements used in motor control
applications. The pins can also be configured as standard output pins.
Write and Write Low output to external memory. WR will go low every external
write. WRL will go low only for external writes to an even byte. Can be used as
standard I/O when not used as WR/WRL.
Input of the oscillator inverter and the internal clock generator. This pin should
be used when using an external clock source.
Output of the oscillator inverter.
Determines the EPROM programming mode.
A low signal in Auto Programming mode indicates that programming is in
process. A high signal indicates programming is complete.
A falling edge in Slave Programming Mode and Auto Configuration Byte
Programming Mode indicates that ports 3 and 4 contain valid programming
address/command information (input to slave).
A falling edge in Slave Programming Mode begins programming. A rising edge
ends programming.
A high signal in Slave Programming Mode and Auto Configuration Byte
Programming Mode indicates the byte programmed correctly.
Cumulative Program Verification. Pin is high if all locations since entering a
programming mode have programmed correctly.
Auto Increment. Active low input enables the auto increment mode. Auto
increment will allow reading or writing of sequential EPROM locations without
address transactions across the PBUS for each read or write.
8XC196MC
ABSOLUTE MAXIMUM RATINGS
NOTICE: This data sheet contains preliminary information on new products in production. The specifications are subject to change without notice. Verify with
your local Intel Sales office that you have the latest
data sheet before finalizing a design.
Ambient Temperature
Under Bias ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ b 40§ C to a 85§ C
Storage Temperature ÀÀÀÀÀÀÀÀÀÀ b 65§ C to a 150§ C
Voltage from EA or VPP
to VSS or ANGNDÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ a 13.00V
Voltage on VPP or EQ
to VSS or ANGND ÀÀÀÀÀÀÀÀÀÀÀÀÀÀ b 0.5V to 13.0V
Voltage on Any Other Pin
to VSS or ANGND ÀÀÀÀÀÀÀÀÀÀÀ b 0.5V to a 7.0V(1)
*WARNING: Stressing the device beyond the ‘‘Absolute
Maximum Ratings’’ may cause permanent damage.
These are stress ratings only. Operation beyond the
‘‘Operating Conditions’’ is not recommended and extended exposure beyond the ‘‘Operating Conditions’’
may affect device reliability.
Power Dissipation ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ1.5W(2)
NOTES:
1. This includes VPP and EA on ROM or CPU only devices.
2. Power dissipation is based on package heat transfer limitations, not device power consumption.
OPERATING CONDITIONS
Description
Min
Max
Units
TA
Symbol
Ambient Temperature Under Bias
b 40
a 85
§C
VCC
Digital Supply Voltage
4.50
5.50
V
VREF
Analog Supply Voltage
4.00
5.50
V
FOSC
Oscillator Frequency
8
16
MHz
NOTE:
ANGND and VSS should be nominally at the same potential. Also VSS and VSS1 must be at the same potential.
DC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
(Over Specified Operating Conditions)
Min
Max
Units
VIL
Input Low Voltage
b 0.5
0.3 VCC
V
Test Conditions
VIH
Input High Voltage
0.7 VCC
VCC a 0.5
V
VOL
Output Low Voltage
Port 2 and 5, P6.6, P6.7,
CLKOUT
0.3
0.45
1.5
V
V
V
IOL e 200 mA
IOL e 3.2 mA
IOL e 7 mA
VOL1
Output Low Voltage on Port 3/4
1.0
V
IOL e 15 mA
VOL2
Output Low Voltage on
Port 6.0–6.5
0.45
V
IOL e 10 mA
VOH
Output High Voltage
VCC b 0.3
VCC b 0.7
VCC b 1.5
V
V
V
IOH e b 200 mA
IOH e b 3.2 mA
IOH e b 7 mA
Vth a –Vthb
Hysteresis Voltage Width on
RESET
0.2
V
Typical
9
8XC196MC
DC ELECTRICAL CHARACTERISTICS
Symbol
Parameter
ILI
Input Leakage Current on All Input
Only Pins
ILI1
(Over Specified Operating Conditions) (Continued)
Min Typ Max Units
Test Conditions
g 10
mA
0V k VIN k VCC – 0.3V (in RESET)
Input Leakage Current on Port0
and Port1
g3
mA
0V k VIN k VREF
IIL
Input Low Current on BD Ports
(Note 1)
b 70
mA
VIN e 0.3 VCC
IIL1
Input Low Current on P5.4 and
P2.6 during Reset
b7
mA
0.2 VCC
IOH
Output High Current on P5.4 and
P2.6 during Reset
mA
0.7 VCC
ICC
Active Mode Current in Reset
70
mA
IREF
A/D Conversion Reference Current
2
5
mA
XTAL1 e 16 MHz,
VCC e VPP e VREF e 5.5V
IIDL
Idle Mode Current
15
30
mA
IPD
Power-Down Mode Current
RRST
RESET Pin Pullup Resistor
CS
Pin Capacitance (Any Pin to VSS)
b2
50
5
6k
50
mA
65k
X
10
pF
NOTES:
1. BD (Bidirectional ports) include:
P2.0 – P2.7, except P2.6
P3.0 – P3.7
P4.0 – P4.7
P5.0 – P5.3
P5.5 – P5.7
2. During normal (non-transient) conditions, the following total current limits apply:
P6.0 – P6.5
IOL: 40 mA IOH: 28 mA
P3
IOL: 90 mA IOH: 42 mA
P4
IOL: 90 mA IOH: 42 mA
P5, CLKOUT
IOL: 35 mA IOH: 35 mA
P2, P6.6, P6.7 IOL: 63 mA IOH: 63 mA
10
VCC e VPP e VREF e 5.5V
FTEST e 1.0 MHz
8XC196MC
EXPLANATION OF AC SYMBOLS
Each symbol is two pairs of letters prefixed by ‘‘T’’ for time. The characters in a pair indicate a signal and its
condition, respectively. Symbols represent the time between the two signal/condition points.
Conditions:
Signals:
H Ð High
A Ð Address
L Ð Low
V Ð Valid
B Ð BHE
C Ð CLKOUT
X
Z
D Ð DATA
G Ð Buswidth
Ð No Longer Valid
Ð Floating
L Ð ALE/ADV
BR Ð BREQ
R Ð RD
W Ð WR/WRH/WRL
X
H Ð HOLD
Ð XTAL1
Y Ð READY
Q Ð Data Out
HA Ð HLDA
AC ELECTRICAL CHARACTERISTICS (Over Specified Operating Conditions)
Test Conditions: Capacitive load on all pins e 100 pF, Rise and fall times e 10 ns, FOSC e 16 MHz.
The system must meet the following specifications to work with the 87C196MC:
Symbol
Parameter
FXTAL
Frequency on XTAL1
TOSC
1/FXTAL
TAVYV
Address Valid to READY Setup
TLLYV
ALE Low to READY Setup
TYLYH
Not READY Time
TCLYX
READY Hold after CLKOUT Low
TLLYX
READY Hold after ALE Low
TAVGV
Address Valid to BUSWIDTH Setup
TLLGV
ALE Low to BUSWIDTH Setup
TCLGX
Buswidth Hold after CLKOUT Low
TAVDV
Address Valid to Input Data Valid
TRLDV
Min
Max
Units
Notes
8
16
MHz
3
62.5
125
ns
2 TOSC b 75
ns
TOSC b 70
ns
No Upper Limit
4
ns
0
TOSC b 30
ns
1
TOSC b 15
2 TOSC b 40
ns
1
2 TOSC b 75
ns
TOSC b 60
0
ns
4
ns
3 TOSC b 55
ns
2
RD Active to Input Data Valid
TOSC b 22
ns
2
TCLDV
CLKOUT Low to Input Data Valid
TOSC b 50
ns
TRHDZ
End of RD to Input Data Float
TOSC
ns
TRXDX
Data Hold after RD Inactive
0
ns
NOTES:
1. If Max is exceeded, additional wait states will occur.
2. If wait states are used, add 2 TOSC * N, where N e number of wait states.
3. Testing performed at 8 MHz. However, the device is static by design and will typically operate below 1 Hz.
4. These timings are included for compatibility with older b90 and BH products. They should not be used for newer highspeed designs.
11
8XC196MC
AC ELECTRICAL CHARACTERISTICS (Continued)
Test Conditions: Capacitive load on all pins e 100 pF, Rise and fall times e 10 ns, FOSC e 16 MHz.
The 87C196MC will meet the following timing specifications:
Symbol
Parameter
Min
30
Max
Units
110
ns
TXHCH
XTAL1 to CLKOUT High or Low
TCLCL
CLKOUT Cycle Time
TCHCL
CLKOUT High Period
TOSC b 10
TOSC a 15
ns
TCLLH
CLKOUT Falling Edge to ALE Rising
b5
15
ns
TLLCH
ALE Falling Edge to CLKOUT Rising
b 20
15
ns
TLHLH
ALE Cycle Time
2 TOSC
ns
4 TOSC
ns
TLHLL
ALE High Period
TOSC b 10
TAVLL
Address Setup to ALE Falling Edge
TOSC b 15
ns
TLLAX
Address Hold after ALE Falling
TOSC b 40
ns
TLLRL
ALE Falling Edge to RD Falling
TOSC b 30
ns
TRLCL
RD Low to CLKOUT Falling Edge
TRLRH
RD Low Period
TRHLH
RD Rising Edge to ALE Rising Edge
TRLAZ
RD Low to Address Float
TLLWL
ALE Falling Edge to WR Falling
TCLWL
CLKOUT Low to WR Falling Edge
TQVWH
Data Stable to WR Rising Edge
TCHWH
CLKOUT High to WR Rising Edge
TOSC a 10
3
ns
4
30
ns
TOSC b 5
TOSC a 25
ns
3
TOSC
TOSC a 25
ns
1
5
ns
TOSC b 10
0
ns
25
TOSC b 23
b 10
ns
ns
15
ns
TWLWH
WR Low Period
TOSC b 30
TWHQX
Data Hold after WR Rising Edge
TOSC b 25
TWHLH
WR Rising Edge to ALE Rising Edge
TOSC b 10
TWHBX
BHE, INST Hold after WR Rising
TOSC b 10
ns
TWHAX
AD8–15 Hold after WR Rising
TOSC b 30
ns
TRHBX
BHE, INST Hold after RD Rising
TOSC b 10
ns
TRHAX
AD8–15 Hold after RD Rising
TOSC b 30
ns
NOTES:
1. Assuming back to back cycles.
2. 8-bit bus only.
3. If wait states are used, add 2 TOSC*N, where N e number of wait states.
12
Notes
TOSC a 15
ns
ns
ns
3
1
2
2
8XC196MC
SYSTEM BUS TIMINGS
270946 – 5
13
8XC196MC
READY TIMINGS (One Wait State)
270946 – 6
BUSWIDTH TIMINGS
270946 – 7
14
8XC196MC
EXTERNAL CLOCK DRIVE
Symbol
Parameter
1/TXLXL
Oscillator Frequency
TXLXL
Oscillator Period
TXHXX
High Time
22
ns
TXLXX
Low Time
22
ns
TXLXH
Rise Time
10
ns
TXHXL
Fall Time
10
ns
EXTERNAL CRYSTAL CONNECTIONS
Min
Max
Units
8
16.0
MHz
62.5
125
ns
EXTERNAL CLOCK CONNECTIONS
270946 – 14
NOTE:
Keep oscillator components close to chip and use
short, direct traces to XTAL1, XTAL2 and VSS. When
using crystals, C1 e 20 pF, C2 e 20 pF. When using
ceramic resonators, consult manufacturer for recommended circuitry.
270946 – 15
* Required if TTL driver used.
Not needed if CMOS driver is used.
EXTERNAL CLOCK DRIVE WAVEFORMS
270946 – 8
An external oscillator may encounter as much as a 100 pF load at XTAL1 when it starts-up. This is due to
interaction between the amplifier and its feedback capacitance. Once the external signal meets the VIL and
VIH specifications the capacitance will not exceed 20 pF.
AC TESTING INPUT, OUTPUT WAVEFORMS
270946 – 9
AC Testing inputs are driven at 3.5V for a Logic ‘‘1’’ and 0.45V for
a Logic ‘‘0’’. Timing measurements are made at 2.0V for a Logic
‘‘1’’ and 0.8V for a Logic ‘‘0’’.
FLOAT WAVEFORMS
270946 – 10
For Timing Purposes a Port Pin is no Longer Floating when a
100 mV change from Load Voltage Occurs and Begins to Float
when a 100 mV change from the Loaded VOH/VOL Level occurs
IOL/IOH e s g 15 mA.
15
8XC196MC
A TO D CHARACTERISTICS
The sample and conversion time of the A/D converter in the 8-bit or 10-bit modes is programmed by
loading a byte into the ADÐTIME Special Function
Register. This allows optimizing the A/D operation
for specific applications. The ADÐTIME register is
functional for all possible values, but the accuracy of
the A/D converter is only guaranteed for the times
specificed in the operating conditions table.
The value loaded into ADÐTIME bits 5, 6, 7 determines the sample time, TSAM, and is calculated using the following formula:
SAM e
(TSAM c FOSC) b 2
8
TSAM e Sample time, ms
FOSC e Processor frequency, MHz
SAM e Value loaded into ADÐTIME
bits 5, 6, 7
SAM must be in the range 1 through 7.
The value loaded into ADÐTIME bits 0–5 determines the conversion time, TCONV, and is calculated
using the following formula:
CONV e
16
(TCONV c FOSC) b 3
b1
2B
TCONV e Conversion time, ms
FOSC e Processor frequency, MHz
B e 8 for 8-bit conversion
B e 10 for 10-bit conversion
CONV e Value loaded into ADÐTIME
bits 0 – 5
CONV must be in the range 2 through 31.
The converter is ratiometric, so absolute accuracy is
dependent on the accuracy and stability of VREF.
VREF must be close to VCC since it supplies both the
resistor ladder and the analog portion of the converter and input port pins. There is also an ADÐTEST
SFR that allows for conversion on ANGND and
VREF as well as adjusting the zero offset. The absolute error listed is WITHOUT doing any adjustments.
A/D CONVERTER SPECIFICATION
The specifications given assume adherence to the
operating conditions section of this data sheet. Testing is performed with VREF e 5.12V and 16.0 MHz
operating frequency. After a conversion is started,
the device is placed in the IDLE mode until the conversion is complete.
8XC196MC
10-BIT MODE A/D OPERATING CONDITIONS
Symbol
Description
Min
Max
Units
TA
Ambient Temperature
b 40
a 85
§C
VCC
Digital Supply Voltage
4.50
5.50
V
VREF
Analog Supply Voltage
4.00
5.50
V(1)
TSAM
Sample Time
1.0
TCONV
Conversion Time
10.0
20.0
ms(2)
FOSC
Oscillator Frequency
8.0
16.0
MHz
ms(2)
NOTES:
ANGND and VSS should nominally be at the same potential.
1. VREF must be within 0.5V of VCC.
2. The value of ADÐTIME is selected to meet these specifications.
10-BIT MODE A/D CHARACTERISTICS
Parameter
Typical(1)
Resolution
Absolute Error
Full Scale Error
0.25 g 0.5
Zero Offset Error
0.25 g 0.5
Non-Linearity
1.0 g 2.0
Differential Non-Linearity
(Over Specified Operating Conditions)
Min
Max
Units*
1024
10
1024
10
Levels
Bits
0
g4
LSBs
LSBs
LSBs
g4
LSBs
l b1
a2
LSBs
g 0.1
0
g 1.0
LSBs
Repeatability
g 0.25
0
Temperature Coefficients:
Offset
Full Scale
Differential Non-Linearity
0.009
0.009
0.009
Channel-to-Channel Matching
Off Isolation
Feedthrough
VCC Power Supply Rejection
b 60
Input Series Resistance
Voltage on Analog Input Pin
DC Input Leakage
LSB/C
LSB/C
LSB/C
dB(2, 3)
b 60
b 60
Sampling Capacitor
LSBs
dB(2)
dB(2)
750
2K
X(4)
ANGND b 0.5
VREF a 0.5
V(5, 6)
3
g1
pF
0
g 3.0
mA
NOTES:
*An ‘‘LSB’’, as used here has a value of approximately 5 mV. (See Embedded Microcontrollers and Processors Handbook
for A/D glossary of terms).
1. These values are expected for most parts at 25§ C but are not tested or guaranteed.
2. DC to 100 KHz.
3. Multiplexer Break-Before-Make is guaranteed.
4. Resistance from device pin, through internal MUX, to sample capacitor.
5. These values may be exceeded if the pin current is limited to g 2 mA.
6. Applying voltages beyond these specifications will degrade the accuracy of other channels being converted.
7. All conversions performed with processor in IDLE mode.
17
8XC196MC
8-BIT MODE A/D OPERATING CONDITIONS
Symbol
Description
Min
Max
Units
TA
Ambient Temperature
b 40
a 85
§C
VCC
Digital Supply Voltage
4.50
5.50
V
VREF
Analog Supply Voltage
4.00
5.50
V(1)
TSAM
Sample Time
1.0
TCONV
Conversion Time
7.0
20.0
ms(2)
FOSC
Oscillator Frequency
8.0
16.0
MHz
ms(2)
NOTES:
ANGND and VSS should nominally be at the same potential.
1. VREF must be within 0.5V of VCC.
2. The value of ADÐTIME is selected to meet these specifications.
8-BIT MODE A/D CHARACTERISTICS
Parameter
Typical(1)
Resolution
Absolute Error
Full Scale Error
g 0.5
Zero Offset Error
g 0.5
Non-Linearity
Differential Non-Linearity
Channel-to-Channel Matching
(Over the Above Operating Conditions)
Min
Max
Units*
256
8
256
8
Level
Bits
0
g1
LSBs
LSBs
LSBs
0
g1
LSBs
l b1
a1
LSBs
0
g 1.0
LSBs
Repeatability
g 0.25
LSBs
Temperature Coefficients:
Offset
Full Scale
Differential Non-Linearity
0.003
0.003
0.003
LSB/C
LSB/C
LSB/C
Off Isolation
Feedthrough
VCC Power Supply Rejection
b 60
Input Series Resistance
Voltage on Analog Input Pin
Sampling Capacitor
DC Input Leakage
dB(2, 3)
b 60
b 60
dB(2)
dB(2)
750
2K
X(4)
VSS b 0.5
VREF a 0.5
V(5, 6)
3
g1
pF
0
g 3.0
mA
NOTES:
*An ‘‘LSB’’ as used here, has a value of approximately 20 mV. (See Embedded Microcontrollers and Processors Handbook
for A/D glossary of terms).
1. These values are expected for most parts at 25§ C but are not tested or guaranteed.
2. DC to 100 KHz.
3. Multiplexer Break-Before-Make is guaranteed.
4. Resistance from device pin, through internal MUX, to sample capacitor.
5. These values may be exceeded if the pin current is limited to g 2 mA.
6. Applying voltages beyond these specifications will degrade the accuracy of other channels being converted.
7. All conversions performed with processor in IDLE mode.
18
8XC196MC
EPROM SPECIFICATIONS
OPERATING CONDITIONS
Symbol
Description
Min
Max
Units
TA
Ambient Temperature during Programming
20
30
§C
VCC
Supply Voltage during Programming
4.5
5.5
V(1)
VREF
Reference Supply Voltage during Programming
4.5
5.5
V(1)
VPP
Programming Voltage
12.25
12.75
V(2)
VEA
EA Pin Voltage
12.25
12.75
V(2)
FOSC
Oscillator Frequency during Auto
and Slave Mode Programming
6.0
8.0
MHz
TOSC
Oscillator Frequency during
Run-Time Programming
6.0
12.0
MHz
NOTES:
1. VCC and VREF should nominally be at the same voltage during programming.
2. VPP and VEA must never exceed the maximum specification, or the device may be damaged.
3. VSS and ANGND should nominally be at the same potential (0V).
4. Load capacitance during Auto and Slave Mode programming e 150 pF.
AC EPROM PROGRAMMING CHARACTERISTICS
Symbol
Parameter
Min
Max
1100
Units
TSHLL
Reset High to First PALE Low
TOSC
TLLLH
PALE Pulse Width
50
TOSC
TAVLL
Address Setup Time
0
TOSC
TLLAX
Address Hold Time
100
TPLDV
PROG Low to Word Dump Valid
TPHDX
Word Dump Data Hold
TDVPL
Data Setup Time
0
TOSC
TPLDX
Data Hold Time
400
TOSC
TPLPH(1)
PROG Pulse Width
50
TOSC
TPHLL
PROG High to Next PALE Low
220
TOSC
TLHPL
PALE High to PROG Low
220
TOSC
TPHPL
PROG High to Next PROG Low
220
TOSC
TPHIL
PROG High to AINC Low
TILIH
AINC Pulse Width
TILVH
TILPL
TPHVL
PROG High to PVER Valid
TOSC
50
50
TOSC
TOSC
0
TOSC
240
TOSC
PVER Hold after AINC Low
50
TOSC
AINC Low to PROG Low
170
TOSC
220
TOSC
NOTE:
1. This specification is for the Word Dump Mode. For programming pulses, use the Modified Quick Pulse Algorithm.
19
8XC196MC
DC EPROM PROGRAMMING CHARACTERISTICS
Symbol
IPP
Parameter
VPP Supply Current (When Programming)
Min
Max
Units
100
mA
NOTE:
Do not apply VPP until VCC is stable and within specifications and the oscillator/clock has stabilized or the device may be
damaged.
SLAVE PROGRAMMING MODE DATA PROGRAM MODE WITH SINGLE PROGRAM PULSE
2709461 – 11
NOTE:
P3.0 must be high (‘‘1’’)
20
8XC196MC
SLAVE PROGRAMMING MODE IN WORD DUMP WITH AUTO INCREMENT
270946 – 12
NOTE:
P3.0 must be low (‘‘0’’)
SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM
WITH REPEATED PROG PULSE AND AUTO INCREMENT
270946 – 13
21
8XC196MC
87C196MC DESIGN
CONSIDERATIONS
When an indirect shift during divide occurs the upper
3 bits of the shift count are not masked completely.
If the shift count register has the value 32*n where n
e 1, 3, 5 or 7, the operand will be shifted 32 times.
This should have resulted in no shift taking place.
DATA SHEET REVISION HISTORY
This data sheet (270946-004) is valid for devices
with a ‘‘B’’ at the end of the topside tracking number.
Data sheets are changed as new device information
becomes available. Verify with your local Intel sales
office that you have the latest version before finalizing a design or ordering devices.
The following important differences exist between
this data sheet (270946-002) and the previous version (270946-003):
1. The data sheet was reorganized to standard format.
2. Added 83C196MC device.
3. Added package thermal characteristics.
4. Added note on missing pins on SDIP package.
5. Removed SFR maps (now in user’s manual).
6. Added note on TLLYV and TLLGV specifications.
7. Changed 10-bit mode TCONV (MIN) to 10.0 ms
from 15.0 ms.
8. Changed 10-bit mode TCONV (MAX) to 20.0 ms
from 18.0 ms.
9. Changed VREF (MIN) in 8- and 10-bit mode to
4.0V from 4.5V.
The following important differences exist between
data sheet 270946-003 and the previous version
(270946-002):
1. The data sheet title was changed to better reflect
the purpose of the 87C196MC as an AC Inverter/
DC Brushless Motor Control Microcontroller.
2. The standard temperature range for this part now
covers b 40§ C to a 85§ C.
22
3. EXTINT function description now includes
WGÐPROTECT (1FCEH) as the name and address of the register used to select positive/negative or high/low detection for EXTINT.
4. The memory range 01F00H – 01FBFH was added
to the SFR map as RESERVED.
5. IIL changed from b 60 mA to b 70 mA.
6. IREF changed from 5 mA to 2 mA maximum and
the typical specification was removed.
7. The READY description of the READY TIMINGS
(One Wait State) graphic was modified to denote
the shifting of the leading edge of READY versus
frequency. At 16 MHz the falling edge of READY
occurs before the falling edge of ALE.
8. AC Testing Input, Output Waveform was
changed to reflect inputs driven at 3.5V for a
Logic ‘‘1’’ and .45V for a Logic ‘‘0’’ and timing
measurements made at 2.0V for a Logic ‘‘1’’
and 0.8V for a Logic ‘‘0’’.
9. Float Waveform was changed from IOL/IOH e
g 15 mA to IOL/IOH s g 15 mA
10. ADÐTIME register for 10-bit conversions was
changed from 0C7H to 0D8H. The number of
sample time states was changed from 24 to 25
states, the conversion time states was changed
from 80 to 240 states, and the total conversion
time for ADÐTIME e D8H replaced the total
conversion time for ADÐTIME e C7H.
11. The number of sample time states for an 8-bit
conversion was changed from 20 states to 21
states.
12. There is a single entry in the ERRATA section of
this version of the data sheet concerning the
results of an indirect shift during divide.
The following important differences exist between
this data sheet (270946-002) and the previous version (270946-001):
1. TA Ambient Temperature Under Bias Min
changed from b 20§ C to b 40§ C.
2. IREF A/D Conversion Reference Current Max
changed from 5 mA to 2 mA.
3. Testing levels changed from TTL values to
CMOS values.
4. A/D Input Series Resistance Max changed from
1.2 KX to 2 KX.
Similar pages