Intersil EL7212CS-T7 High speed, dual channel power mosfet driver Datasheet

EL7202, EL7212, EL7222
®
Data Sheet
July 3, 2006
High Speed, Dual Channel Power
MOSFET Drivers
FN7282.2
Features
• Industry standard driver replacement
The EL7202, EL7212, EL7222 ICs are matched dual-drivers
that improve the operation of the industry standard DS0026
clock drivers. The Elantec versions are very high speed
drivers capable of delivering peak currents of 2.0 amps into
highly capacitive loads. The high speed performance is
achieved by means of a proprietary “Turbo-Driver” circuit
that speeds up input stages by tapping the wider voltage
swing at the output. Improved speed and drive capability are
enhanced by matched rise and fall delay times. These
matched delays maintain the integrity of input-to-output
pulse-widths to reduce timing errors and clock skew
problems. This improved performance is accompanied by a
10 fold reduction in supply currents over bipolar drivers, yet
without the delay time problems commonly associated with
CMOS devices. Dynamic switching losses are minimized
with non-overlapped drive techniques.
• Improved response times
• Matched rise and fall times
• Reduced clock skew
• Low output impedance
• Low input capacitance
• High noise immunity
• Improved clocking rate
• Low supply current
• Wide operating voltage range
• Pb-Free available (RoHS compliant)
Applications
• Clock/line drivers
Pinouts
EL7222
(8-PIN PDIP, SO)
TOP VIEW
EL7212
(8-PIN PDIP, SO)
TOP VIEW
• CCD Drivers
• Ultra-sound transducer drivers
• Power MOSFET drivers
• Switch mode power supplies
• Class D switching amplifiers
• Ultrasonic and RF generators
• Pulsed circuits
COMPLEMENTARY
DRIVERS
INVERTING
DRIVERS
EL7202
(8-PIN PDIP, SO)
TOP VIEW
NON-INVERTING
DRIVERS
Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003, 2005-2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
EL7202, EL7212, EL7222
Ordering Information
Part Number
PART
MARKING
TAPE &
REEL
PACKAGE
PKG.
DWG. #
EL7202CN
EL7202CN
-
8 Ld PDIP
MDP0031
EL7202CS
7202CS
-
8 Ld SOIC
MDP0027
EL7202CS-T7
7202CS
7”
8 Ld SOIC
MDP0027
EL7202CS-T13
7202CS
13”
8 Ld SOIC
MDP0027
EL7202CSZ
(See Note)
7202CSZ
-
8 Ld SOIC
(Pb-free)
MDP0027
EL7202CSZ-T7
(See Note)
7202CSZ
7”
8 Ld SOIC
(Pb-free)
MDP0027
EL7202CSZ-T13
(See Note)
7202CSZ
13”
8 Ld SOIC
(Pb-free)
MDP0027
EL7212CN
EL7212CN
-
8 Ld PDIP
MDP0031
EL7212CNZ
EL7212CN Z
-
8 Ld PDIP*
(Pb-free)
MDP0031
EL7212CS
7212CS
-
8 Ld SOIC
MDP0027
EL7212CS-T7
7212CS
7”
8 Ld SOIC
MDP0027
EL7212CS-T13
7212CS
13”
8 Ld SOIC
MDP0027
EL7212CSZ
(See Note)
7212CSZ
-
8 Ld SOIC
(Pb-free)
MDP0027
EL7212CSZ-T7
(See Note)
7212CSZ
7”
8 Ld SOIC
(Pb-free)
MDP0027
EL7212CSZ-T13
(See Note)
7212CSZ
13”
8 Ld SOIC
(Pb-free)
MDP0027
EL7222CN
EL7222CN
-
8 Ld PDIP
MDP0031
EL7222CS
7222CS
-
8 Ld SOIC
MDP0027
EL7222CS-T7
7222CS
7”
8 Ld SOIC
MDP0027
EL7222CS-T13
7222CS
13”
8 Ld SOIC
MDP0027
EL7222CSZ
(See Note)
7222CSZ
-
8 Ld SOIC
(Pb-free)
MDP0027
EL7222CSZ-T7
(See Note)
7222CSZ
7”
8 Ld SOIC
(Pb-free)
MDP0027
EL7222CSZ-T13
(See Note)
7222CSZ
13”
8 Ld SOIC
(Pb-free)
MDP0027
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both
SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the
Pb-free requirements of IPC/JEDEC J STD-020.
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
2
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Absolute Maximum Ratings (TA = 25°C)
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C
Power Dissipation
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW
PDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW
Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+
Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
TA = 25°C, V = 15V unless otherwise specified
parameter
Description
Test Conditions
Min
Typ
Max
Units
INPUT
VIH
Logic “1” Input Voltage
IIH
Logic “1” Input Current
VIL
Logic “0” Input Voltage
IIL
Logic “0” Input Current
VHVS
Input Hysteresis
2.4
@V+
V
0.1
@0V
0.1
10
µA
0.8
V
10
µA
0.3
V
OUTPUT
ROH
Pull-Up Resistance
IOUT = -100mA
3
6
Ω
ROL
Pull-Down Resistance
IOUT = +100mA
4
6
Ω
IPK
Peak Output Current
Source
Sink
2
2
IDC
Continuous Output Current
Source/Sink
Power Supply Current
Inputs High/EL7202
Inputs High/EL7212
Inputs High/EL7222
A
100
mA
POWER SUPPLY
IS
VS
7.5
2.5
5.0
mA
15
V
Typ
Max
Units
CL = 500pF
CL = 1000pF
7.5
10
20
CL = 500pF
CL = 1000pF
10
13
20
Operating Voltage
AC Electrical Specifications
4.5
1
2.5
4.5
TA = 25°C, V = 15V unless otherwise specified
parameter
Description
Test Conditions
Min
SWITCHING CHARACTERISTICS
tR
tF
Rise Time
Fall Time
ns
ns
tD1
Turn-On Delay Time
See Timing Table
18
25
ns
tD2
Turn-Off Delay Time
See Timing Table
20
25
ns
3
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Timing Table
Standard Test Configuration
Simplified Schematic
4
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Typical Performance Curves
MAX POWER/DERATING CURVES
INPUT CURRENT vs VOLTAGE
QUIESCENT SUPPLY CURRENT
5
SWITCH THRESHOLD vs SUPPLY VOLTAGE
PEAK DRIVE vs SUPPLY VOLTAGE
“ON” RESISTANCE vs
SUPPLY VOLTAGE
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Typical Performance Curves
(Continued)
AVERAGE SUPPLY CURRENT vs
VOLTAGE AND FREQUENCY
AVERAGE SUPPLY CURRENT
vs CAPACITIVE LOAD
RISE/FALL TIME vs LOAD
RISE/FALL TIME vs SUPPLY VOLTAGE
PROPAGATION DELAY vs SUPPLY VOLTAGE
RISE/FALL TIME vs TEMPERATURE
DELAY vs TEMPERATURE
6
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
EL7212 Macro Model
**** EL7212 model ****
*
input
*
|
gnd
*
|
|
Vsupply
*
|
|
| Vout
.subckt M7212 2 3 6 7
V1 12 3 1.6
R1 13 15 1k
R2 14 15 5k
R5 11 12 100
C1 15 3 43.3 pF
D1 14 13 dmod
X1 13 11 2 3 comp1
X2 16 12 15 3 comp1
sp 6 7 16 3 spmod
sn 7 3 16 3 snmod
g1 11 0 13 0 938µ
.model dmod d
.model spmod vswitch ron3 roff2meg von1 voff1.5
.model snmod vswitch ron4 roff2meg von3 voff2
.ends M7212
.subckt comp1 out inp inm vss
e1 out vss table { (v(inp) v(inm))* 5000} (0,0) (3.2,3.2)
Rout out vss 10meg
Rinp inp vss 10meg
Rinm inm vss 10meg
.ends comp1
7
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SYMBOL
SO-8
SO-14
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
±0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
±0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
±0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
±0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
±0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
±0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
±0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
±0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
N
8
14
16
Rev. L 2/01
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
8
FN7282.2
July 3, 2006
EL7202, EL7212, EL7222
Plastic Dual-In-Line Packages (PDIP)
E
D
A2
SEATING
PLANE
L
N
A
PIN #1
INDEX
E1
c
e
b
A1
NOTE 5
1
eA
eB
2
N/2
b2
MDP0031
PLASTIC DUAL-IN-LINE PACKAGE
SYMBOL
PDIP8
PDIP14
PDIP16
PDIP18
PDIP20
TOLERANCE
A
0.210
0.210
0.210
0.210
0.210
MAX
A1
0.015
0.015
0.015
0.015
0.015
MIN
A2
0.130
0.130
0.130
0.130
0.130
±0.005
b
0.018
0.018
0.018
0.018
0.018
±0.002
b2
0.060
0.060
0.060
0.060
0.060
+0.010/-0.015
c
0.010
0.010
0.010
0.010
0.010
+0.004/-0.002
D
0.375
0.750
0.750
0.890
1.020
±0.010
E
0.310
0.310
0.310
0.310
0.310
+0.015/-0.010
E1
0.250
0.250
0.250
0.250
0.250
±0.005
e
0.100
0.100
0.100
0.100
0.100
Basic
eA
0.300
0.300
0.300
0.300
0.300
Basic
eB
0.345
0.345
0.345
0.345
0.345
±0.025
L
0.125
0.125
0.125
0.125
0.125
±0.010
N
8
14
16
18
20
Reference
NOTES
1
2
Rev. B 2/99
NOTES:
1. Plastic or metal protrusions of 0.010” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions E and eA are measured with the leads constrained perpendicular to the seating plane.
4. Dimension eB is measured with the lead tips unconstrained.
5. 8 and 16 lead packages have half end-leads as shown.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
9
FN7282.2
July 3, 2006
Similar pages