Altera EP2AGX45DF29C6N Volume 3: device datasheet and addendum Datasheet

Arria II Device Handbook Volume 3: Device Datasheet and
Addendum
Arria II Device Handbook
Volume 3: Device Datasheet and Addendum
101 Innovation Drive
San Jose, CA 95134
www.altera.com
AIIGX5V3-4.3
Document publication date:
July 2012
© 2012 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat.
& Tm. Off. and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective
holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance
with Altera’s standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or
liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera
customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or
services.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Contents
Chapter Revision Dates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Section I. Device Datasheet and Addendum for Arria II Devices
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Chapter 1. Device Datasheet for Arria II Devices
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Maximum Allowed I/O Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7
Schmitt Trigger Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14
I/O Standard Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15
Power Consumption for the Arria II Device Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–20
Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–21
Transceiver Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–21
Core Performance Specifications for the Arria II Device Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–53
Clock Tree Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–53
PLL Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–53
DSP Block Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–57
Embedded Memory Block Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–58
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–60
JTAG Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–60
Chip-Wide Reset (Dev_CLRn) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–60
Periphery Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–61
High-Speed I/O Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–61
External Memory Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–68
Duty Cycle Distortion (DCD) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–71
IOE Programmable Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–72
I/O Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–73
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–74
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–77
Chapter 2. Addendum for the Arria II Device Handbook
Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
High-Speed LVDS I/O with DPA and Soft CDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Auto-Calibrating External Memory Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Connecting a Serial Configuration Device to an Arria II Device Family on AS Interface . . . . . . . . . . . 2–1
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Additional Information
How to Contact Altera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info–1
Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info–1
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
iv
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Contents
July 2012 Altera Corporation
Chapter Revision Dates
The chapters in this document, Arria II Device Handbook Volume 3: Device Datasheet
and Addendum, were revised on the following dates. Where chapters or groups of
chapters are available separately, part numbers are listed.
Chapter 1.
Device Datasheet for Arria II Devices
Revised:
July 2012
Part Number: AIIGX53001-4.3
Chapter 2.
Addendum for the Arria II Device Handbook
Revised:
December 2010
Part Number: AIIGX53002-2.0
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
vi
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Chapter Revision Dates
July 2012 Altera Corporation
Section I. Device Datasheet and
Addendum for Arria II Devices
This section provides information about the Arria® II device family datasheet and
addendum. This section includes the following chapters:
■
Chapter 1, Device Datasheet for Arria II Devices
■
Chapter 2, Addendum for the Arria II Device Handbook
Revision History
Refer to each chapter for its own specific revision history. For information on when
each chapter was updated, refer to the Chapter Revision Dates section, which appears
in this volume.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
I–2
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Section I: Device Datasheet and Addendum for Arria II Devices
Revision History
July 2012 Altera Corporation
1. Device Datasheet for Arria II Devices
July 2012
AIIGX53001-4.3
AIIGX53001-4.3
This chapter describes the electrical and switching characteristics of the Arria® II
device family. The Arria II device family includes the Arria II GX and GZ devices.
Electrical characteristics include operating conditions and power consumption.
Switching characteristics include transceiver specifications, core, and periphery
performance. This chapter also describes I/O timing, including programmable I/O
element (IOE) delay and programmable output buffer delay.
f For information regarding the densities and packages of devices in the Arria II device
family, refer to Overview for the Arria II Device Family chapter.
This chapter contains the following sections:
■
“Electrical Characteristics” on page 1–1
■
“Transceiver Performance Specifications” on page 1–21
■
“Glossary” on page 1–74
Electrical Characteristics
The following sections describe the electrical characteristics.
Operating Conditions
Arria II devices are rated according to a set of defined parameters. To maintain the
highest possible performance and reliability of Arria II devices, you must consider the
operating requirements described in this chapter.
Arria II devices are offered in both commercial and industrial grades. Arria II GX
devices are offered in –4 (fastest), –5, and –6 (slowest) commercial speed grades and
–3 and –5 industrial speed grades. Arria II GZ devices are offered in –3 and –4 speed
grades for both commercial and industrial grades.
1
In this chapter, a prefix associated with the operating temperature range is attached to
the speed grades; commercial with the "C" prefix and industrial with the “I” prefix.
Commercial devices are indicated as C4, C5, and C6 speed grade, and the industrial
devices are indicated as I3 and I5.
Absolute Maximum Ratings
Absolute maximum ratings define the maximum operating conditions for Arria II
devices. The values are based on experiments conducted with the device and
theoretical modeling of breakdown and damage mechanisms. The functional
operation of the device is not implied under these conditions. Table 1–1 lists the
absolute maximum ratings for Arria II GX devices. Table 1–2 lists the absolute
maximum ratings for Arria II GZ devices.
© 2012 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012
Subscribe
1–2
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
c Conditions beyond those listed in Table 1–1 and Table 1–2 may cause permanent
damage to the device. Additionally, device operation at the absolute maximum
ratings for extended periods of time may have adverse effects on the device.
Table 1–1 lists the absolute maximum ratings for Arria II GX devices.
Table 1–1. Absolute Maximum Ratings for Arria II GX Devices
Symbol
Description
Minimum
Maximum
Unit
VCC
Supplies power to the core, periphery, I/O registers, PCI Express®
(PIPE) (PCIe) HIP block, and transceiver PCS
–0.5
1.35
V
VCCCB
Supplies power for the configuration RAM bits
–0.5
1.8
V
VCCBAT
Battery back-up power supply for design security volatile key register
–0.5
3.75
V
VCCPD
Supplies power to the I/O pre-drivers, differential input buffers, and
MSEL circuitry
–0.5
3.75
V
VCCIO
Supplies power to the I/O banks
–0.5
3.9
V
VCCD_PLL
Supplies power to the digital portions of the PLL
–0.5
1.35
V
VCCA_PLL
Supplies power to the analog portions of the PLL and device-wide
power management circuitry
–0.5
3.75
V
VI
DC input voltage
–0.5
4.0
V
IOUT
DC output current, per pin
–25
40
mA
VCCA
Supplies power to the transceiver PMA regulator
—
3.75
V
VCCL_GXB
Supplies power to the transceiver PMA TX, PMA RX, and clocking
—
1.21
V
VCCH_GXB
Supplies power to the transceiver PMA output (TX) buffer
—
1.8
V
TJ
Operating junction temperature
–55
125
°C
TSTG
Storage temperature (no bias)
–65
150
°C
Table 1–2 lists the absolute maximum ratings for Arria II GZ devices.
Table 1–2. Absolute Maximum Ratings for Arria II GZ Devices (Part 1 of 2)
Symbol
Description
Minimum
Maximum
Unit
VCC
Supplies power to the core, periphery, I/O registers, PCIe HIP block, and
transceiver PCS
-0.5
1.35
V
VCCCB
Power supply to the configuration RAM bits
-0.5
1.8
V
VCCPGM
Supplies power to the configuration pins
-0.5
3.75
V
VCCAUX
Auxiliary supply
-0.5
3.75
V
VCCBAT
Supplies battery back-up power for design security volatile key register
-0.5
3.75
V
VCCPD
Supplies power to the I/O pre-drivers, differential input buffers, and
MSEL circuitry
-0.5
3.75
V
VCCIO
Supplies power to the I/O banks
-0.5
3.9
V
VCC_CLKIN
Supplies power to the differential clock input
-0.5
3.75
V
VCCD_PLL
Supplies power to the digital portions of the PLL
-0.5
1.35
V
VCCA_PLL
Supplies power to the analog portions of the PLL and device-wide
power management circuitry
-0.5
3.75
V
VI
DC input voltage
-0.5
4.0
V
IOUT
DC output current, per pin
-25
40
mA
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–3
Table 1–2. Absolute Maximum Ratings for Arria II GZ Devices (Part 2 of 2)
Symbol
Description
Minimum
Maximum
Unit
VCCA_L
Supplies transceiver high voltage power (left side)
-0.5
3.75
V
VCCA_R
Supplies transceiver high voltage power (right side)
-0.5
3.75
V
VCCHIP_L
Supplies transceiver HIP digital power (left side)
-0.5
1.35
V
VCCR_L
Supplies receiver power (left side)
-0.5
1.35
V
VCCR_R
Supplies receiver power (right side)
-0.5
1.35
V
VCCT_L
Supplies transmitter power (left side)
-0.5
1.35
V
VCCT_R
Supplies transmitter power (right side)
-0.5
1.35
V
VCCL_GXBLn
(1)
Supplies power to the transceiver PMA TX, PMA RX, and clocking (left
side)
-0.5
1.35
V
VCCL_GXBRn
(1)
Supplies power to the transceiver PMA TX, PMA RX, and clocking (right
side)
-0.5
1.35
V
VCCH_GXBLn
(1)
Supplies power to the transceiver PMA output (TX) buffer (left side)
-0.5
1.8
V
VCCH_GXBRn
(1)
Supplies power to the transceiver PMA output (TX) buffer (right side)
-0.5
1.8
V
TJ
Operating junction temperature
-55
125
°C
TSTG
Storage temperature (no bias)
-65
150
°C
Note to Table 1–2:
(1) n = 0, 1, or 2.
Maximum Allowed Overshoot and Undershoot Voltage
During transitions, input signals may overshoot to the voltage shown in Table 1–3 and
undershoot to –2.0 V for magnitude of currents less than 100 mA and periods shorter
than 20 ns.
Table 1–3 lists the Arria II GX and GZ maximum allowed input overshoot voltage and
the duration of the overshoot voltage as a percentage over the device lifetime. The
maximum allowed overshoot duration is specified as a percentage of high-time over
the lifetime of the device. A DC signal is equivalent to 100% duty cycle. For example,
a signal that overshoots to 4.3 V can only be at 4.3 V for 5.41% over the lifetime of the
device; for a device lifetime of 10 years, this amounts to 5.41/10ths of a year.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–4
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–3. Maximum Allowed Overshoot During Transitions for Arria II Devices
Symbol
VI (AC)
Description
AC Input Voltage
Condition (V)
Overshoot Duration as % of
High Time
Unit
4.0
100.000
%
4.05
79.330
%
4.1
46.270
%
4.15
27.030
%
4.2
15.800
%
4.25
9.240
%
4.3
5.410
%
4.35
3.160
%
4.4
1.850
%
4.45
1.080
%
4.5
0.630
%
4.55
0.370
%
4.6
0.220
%
Maximum Allowed I/O Operating Frequency
Table 1–4 lists the maximum allowed I/O operating frequency for Arria II GX I/Os
using the specified I/O standards to ensure device reliability.
Table 1–4. Maximum Allowed I/O Operating Frequency for Arria II GX Devices
I/O Standard
I/O Frequency (MHz)
HSTL-18 and HSTL-15
333
SSTL -15
400
SSTL-18
333
2.5-V LVCMOS
260
3.3-V and 3.0-V LVTTL
3.3-V, 3.0-V, 1.8-V, and 1.5-V LVCMOS
PCI and PCI-X
250
SSTL-2
1.2-V LVCMOS HSTL-12
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
200
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–5
Recommended Operating Conditions
This section lists the functional operation limits for AC and DC parameters for
Arria II GX and GZ devices. All supplies are required to monotonically reach their
full-rail values without plateaus within tRAMP .
Table 1–5 lists the recommended operating conditions for Arria II GX devices.
Table 1–5. Recommended Operating Conditions for Arria II GX Devices (Note 1) (Part 1 of 2)
Symbol
Description
Condition
Minimum
Typical
Maximum
Unit
VCC
Supplies power to the core, periphery, I/O
registers, PCIe HIP block, and transceiver
PCS
—
0.87
0.90
0.93
V
VCCCB
Supplies power to the configuration RAM
bits
—
1.425
1.50
1.575
V
VCCBAT
(2)
Battery back-up power supply for design
security volatile key registers
—
1.2
—
3.3
V
Supplies power to the I/O pre-drivers,
differential input buffers, and MSEL
circuitry
—
3.135
3.3
3.465
V
VCCPD
(3)
—
2.85
3.0
3.15
V
—
2.375
2.5
2.625
V
—
3.135
3.3
3.465
V
—
2.85
3.0
3.15
V
—
2.375
2.5
2.625
V
—
1.71
1.8
1.89
V
—
1.425
1.5
1.575
V
—
1.14
1.2
1.26
V
VCCIO
Supplies power to the I/O banks (4)
VCCD_PLL
Supplies power to the digital portions of the
PLL
—
0.87
0.90
0.93
V
VCCA_PLL
Supplies power to the analog portions of
the PLL and device-wide power
management circuitry
—
2.375
2.5
2.625
V
VI
DC Input voltage
—
–0.5
—
3.6
V
VO
Output voltage
—
0
—
VCCIO
V
VCCA
Supplies power to the transceiver PMA
regulator
—
2.375
2.5
2.625
V
VCCL_GXB
Supplies power to the transceiver PMA TX,
PMA RX, and clocking
—
1.045
1.1
1.155
V
VCCH_GXB
Supplies power to the transceiver PMA
output (TX) buffer
—
1.425
1.5
1.575
V
TJ
Operating junction temperature
Commercial
0
—
85
°C
Industrial
–40
—
100
°C
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–6
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–5. Recommended Operating Conditions for Arria II GX Devices (Note 1) (Part 2 of 2)
Symbol
tRAMP
Description
Power Supply Ramp time
Condition
Minimum
Typical
Maximum
Unit
Normal POR
0.05
—
100
ms
Fast POR
0.05
—
4
ms
Notes to Table 1–5:
(1) For more information about supply pin connections, refer to the Arria II Device Family Pin Connection Guidelines.
(2) Altera recommends a 3.0-V nominal battery voltage when connecting VCCBAT to a battery for volatile key backup. If you do not use the volatile
security key, you may connect the VCCBAT to either GND or a 3.0-V power supply.
(3) VCCPD must be 2.5-V for I/O banks with 2.5-V and lower VCCIO, 3.0-V for 3.0-V VCCIO, and 3.3-V for 3.3-V VCCIO.
(4) VCCIO for 3C and 8C I/O banks where the configuration pins reside only supports 3.3-, 3.0-, 2.5-, or 1.8-V voltage levels.
Table 1–6 lists the recommended operating conditions for Arria II GZ devices.
Table 1–6. Recommended Operating Conditions for Arria II GZ Devices (Note 6) (Part 1 of 2)
Symbol
Description
Condition
Minimum
Typical
Maximum
Unit
VCC
Core voltage and periphery circuitry power
supply
—
0.87
0.90
0.93
V
VCCCB
Supplies power for the configuration RAM
bits
—
1.45
1.50
1.55
V
VCCAUX
Auxiliary supply
—
2.375
2.5
2.625
V
I/O pre-driver (3.0 V) power supply
—
2.85
3.0
3.15
V
I/O pre-driver (2.5 V) power supply
—
2.375
2.5
2.625
V
I/O buffers (3.0 V) power supply
—
2.85
3.0
3.15
V
I/O buffers (2.5 V) power supply
—
2.375
2.5
2.625
V
I/O buffers (1.8 V) power supply
—
1.71
1.8
1.89
V
I/O buffers (1.5 V) power supply
—
1.425
1.5
1.575
V
I/O buffers (1.2 V) power supply
—
1.14
1.2
1.26
V
Configuration pins (3.0 V) power supply
—
2.85
3.0
3.15
V
Configuration pins (2.5 V) power supply
—
2.375
2.5
2.625
V
Configuration pins (1.8 V) power supply
—
1.71
1.8
1.89
V
VCCA_PLL
PLL analog voltage regulator power supply
—
2.375
2.5
2.625
V
VCCD_PLL
PLL digital voltage regulator power supply
—
0.87
0.90
0.93
V
VCC_CLKIN
Differential clock input power supply
—
2.375
2.5
2.625
V
VCCBAT (1)
Battery back-up power supply (For design
security volatile key register)
—
1.2
—
3.3
V
VI
DC input voltage
—
–0.5
—
3.6
V
VO
Output voltage
—
0
—
VCCIO
V
VCCA_L
Transceiver high voltage power (left side)
—
VCCA_R
Transceiver high voltage power (right side)
—
2.85/2.375
3.0/2.5 (4)
3.15/2.625
V
VCCHIP_L
Transceiver HIP digital power (left side)
—
0.87
0.9
0.93
V
VCCR_L
Receiver power (left side)
—
1.05
1.1
1.15
V
VCCR_R
Receiver power (right side)
—
1.05
1.1
1.15
V
VCCT_L
Transmitter power (left side)
—
1.05
1.1
1.15
V
VCCT_R
Transmitter power (right side)
—
1.05
1.1
1.15
V
VCCPD (2)
VCCIO
VCCPGM
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–7
Table 1–6. Recommended Operating Conditions for Arria II GZ Devices (Note 6) (Part 2 of 2)
Symbol
Description
Condition
Minimum
Typical
Maximum
Unit
VCCL_GXBLn
(3)
Transceiver clock power (left side)
—
1.05
1.1
1.15
V
VCCL_GXBRn
(3)
Transceiver clock power (right side)
—
1.05
1.1
1.15
V
VCCH_GXBLn
(3)
Transmitter output buffer power (left side)
—
VCCH_GXBRn
(3)
1.33/1.425
1.4/1.5 (5)
1.575
V
Transmitter output buffer power (right side)
TJ
Operating junction temperature
Commercial
0
—
85
°C
Industrial
–40
—
100
°C
Normal POR
(PORSEL=0)
0.05
—
100
ms
Fast POR
(PORSEL=1)
0.05
—
4
ms
tRAMP
Power supply ramp time
—
Notes to Table 1–6:
(1) Altera recommends a 3.0-V nominal battery voltage when connecting VCCBAT to a battery for volatile key backup. If you do not use the volatile
security key, you may connect the VCCBAT to either GND or a 3.0-V power supply.
(2) VCCPD must be 2.5 V when VCCIO is 2.5, 1.8, 1.5, or 1.2 V. VCCPD must be 3.0 V when VCCIO is 3.0 V.
(3) n = 0, 1, or 2.
(4) VCCA_L/R must be connected to a 3.0-V supply if the clock multiplier unit (CMU) phase-locked loop (PLL), receiver clock data recovery (CDR), or
both, are configured at a base data rate > 4.25 Gbps. For data rates up to 4.25 Gbps, you can connect VCCA_L/R to either 3.0 V or 2.5 V.
(5) VCCH_GXBL/R must be connected to a 1.4-V supply if the transmitter channel data rate is > 6.5 Gbps. For data rates up to 6.5 Gbps, you can connect
VCCH_GXBL/R to either 1.4 V or 1.5 V.
(6) Transceiver power supplies do not have power-on-reset (POR) circuitry. After initial power-up, violating the transceiver power supply operating
conditions could lead to unpredictable link behavior.
DC Characteristics
This section lists the supply current, I/O pin leakage current, on-chip termination
(OCT) accuracy and variation, input pin capacitance, internal weak pull-up and
pull-down resistance, hot socketing, and Schmitt trigger input specifications.
Supply Current
Standby current is the current the device draws after the device is configured with no
inputs or outputs toggling and no activity in the device. Because these currents vary
largely with the resources used, use the Microsoft Excel-based Early Power Estimator
(EPE) to get supply current estimates for your design.
f For more information about power estimation tools, refer to the PowerPlay Early Power
Estimator User Guide and the PowerPlay Power Analysis chapter.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–8
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
I/O Pin Leakage Current
Table 1–7 lists the Arria II GX I/O pin leakage current specifications.
Table 1–7. I/O Pin Leakage Current for Arria II GX Devices
Symbol
Description
Conditions
Min
Typ
Max
Unit
II
Input pin
VI = 0 V to VCCIOMAX
–10
—
10
µA
IOZ
Tri-stated I/O pin
VO = 0 V to VCCIOMAX
–10
—
10
µA
Table 1–8 lists the Arria II GZ I/O pin leakage current specifications.
Table 1–8. I/O Pin Leakage Current for Arria II GZ Devices
Symbol
Description
Conditions
Min
Typ
Max
Unit
II
Input pin
VI = 0 V to VCCIOMAX
–20
—
20
µA
IOZ
Tri-stated I/O pin
VO = 0 V to VCCIOMAX
–20
—
20
µA
Bus Hold
Bus hold retains the last valid logic state after the source driving it either enters the
high impedance state or is removed. Each I/O pin has an option to enable bus hold in
user mode. Bus hold is always disabled in configuration mode.
Table 1–9 lists bus hold specifications for Arria II GX devices.
Table 1–9. Bus Hold Parameters for Arria II GX Devices (Note 1)
VCCIO (V)
Parameter Symbol
Cond.
1.2
1.5
1.8
2.5
3.0
3.3
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Bus-hold
low,
sustaining
current
ISUSL
VIN > VIL
(max.)
8
—
12
—
30
—
50
—
70
—
70
—
µA
Bus-hold
high,
sustaining
current
ISUSH
VIN < VIL
(min.)
–8
—
–12
—
–30
—
–50
—
–70
—
–70
—
µA
Bus-hold
low,
overdrive
current
IODL
0 V < VIN <
VCCIO
—
125
—
175
—
200
—
300
—
500
—
500
µA
Bus-hold
high,
overdrive
current
IODH
0 V < VIN <
VCCIO
—
–125
—
–175
—
–200
—
–300
—
–500
—
–500
µA
Bus-hold
trip point
VTRIP
—
0.3
0.9
0.68
1.07
0.7
1.7
0.8
2
0.8
2
V
0.375 1.125
Note to Table 1–9:
(1) The bus-hold trip points are based on calculated input voltages from the JEDEC standard.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–9
Table 1–10 lists the bus hold specifications for Arria II GZ devices.
Table 1–10. Bus Hold Parameters for Arria II GZ Devices
VCCIO (V)
Parameter
Symbol
Cond.
1.2
Min
Bus-hold
Low
sustaining
current
ISUSL
Bus-hold
High
sustaining
current
ISUSH
Bus-hold
Low
overdrive
current
IODL
Bus-hold
High
overdrive
current
Bus-hold
trip point
VIN > VIL
1.5
Max
Min
1.8
Max
Min
2.5
Max
Min
3.0
Max
Min
Unit
Max
22.5
—
25.0
—
30.0
—
50.0
—
70.0
—
µA
-22.5
—
-25.0
—
-30.0
—
-50.0
—
-70.0
—
µA
0V < VIN <
VCCIO
—
120
—
160
—
200
—
300
—
500
µA
IODH
0V < VIN <
VCCIO
—
-120
—
-160
—
-200
—
-300
—
-500
µA
VTRIP
—
0.45
0.95
0.50
1.00
0.68
1.07
0.70
1.70
0.80
2.00
V
(max.)
VIN < VIH
(min.)
OCT Specifications
Table 1–11 lists the Arria II GX device and differential OCT with and without
calibration accuracy.
Table 1–11. OCT With and Without Calibration Specification for Arria II GX Device I/Os (Note 1) (Part 1 of 2)
Calibration Accuracy
Symbol
Description
Conditions (V)
Unit
Commercial
Industrial
25- RS
3.0, 2.5
25- series OCT
without calibration
VCCIO = 3.0, 2.5
± 30
± 40
%
50- RS
3.0, 2.5
50- series OCT
without calibration
VCCIO = 3.0, 2.5
± 30
± 40
%
25- RS
1.8
25- series OCT
without calibration
VCCIO = 1.8
± 40
± 50
%
50- RS
1.8
50- series OCT
without calibration
VCCIO = 1.8
± 40
± 50
%
25- RS
1.5, 1.2
25- series OCT
without calibration
VCCIO = 1.5, 1.2
± 50
± 50
%
50- RS
1.5, 1.2
50- series OCT
without calibration
VCCIO = 1.5, 1.2
± 50
± 50
%
25- RS
3.0, 2.5, 1.8, 1.5,
1.2
25- series OCT
with calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
± 10
± 10
%
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–10
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–11. OCT With and Without Calibration Specification for Arria II GX Device I/Os (Note 1) (Part 2 of 2)
Calibration Accuracy
Symbol
Description
Conditions (V)
Unit
Commercial
Industrial
50- RS
3.0, 2.5, 1.8, 1.5,
1.2
50- series OCT
with calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
± 10
± 10
%
100- RD
2.5
100- differential
OCT without
calibration
VCCIO = 2.5
± 30
± 30
%
Note to Table 1–11:
(1) OCT with calibration accuracy is valid at the time of calibration only.
Table 1–12 lists the OCT termination calibration accuracy specifications for
Arria II GZ devices.
Table 1–12. OCT with Calibration Accuracy Specifications for Arria II GZ Devices (Note 1)
Calibration Accuracy
Symbol
Description
Conditions (V)
Unit
C2
C3,I3
C4,I4
25- RS
3.0, 2.5, 1.8, 1.5,
1.2 (2)
25- series OCT
with calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
±8
±8
±8
%
50- RS
3.0, 2.5, 1.8, 1.5,
1.2
50-internal series
OCT with calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
±8
±8
±8
%
50- RT
2.5, 1.8, 1.5, 1.2
50- internal parallel
OCT with calibration
VCCIO = 2.5, 1.8,
1.5, 1.2
± 10
± 10
± 10
%
20- , 40- , and
60- RS
3.0, 2.5, 1.8, 1.5,
1.2 (3)
20- , 40- and
60- RS expanded
range for internal
series OCT with
calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
± 10
± 10
± 10
%
25- RS_left_shift
3.0, 2.5, 1.8, 1.5,
1.2
25- RS_left_shift
internal left shift
series OCT with
calibration
VCCIO = 3.0, 2.5,
1.8, 1.5, 1.2
± 10
± 10
± 10
%
Notes to Table 1–12:
(1) OCT calibration accuracy is valid at the time of calibration only.
(2) 25- RS is not supported for 1.5 V and 1.2 V in Row I/O.
(3) 20- RS is not supported for 1.5 V and 1.2 V in Row I/O.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–11
The calibration accuracy for calibrated series and parallel OCTs are applicable at the
moment of calibration. When process, voltage, and temperature (PVT) conditions
change after calibration, the tolerance may change.
Table 1–13 lists the Arria II GZ OCT without calibration resistance tolerance to PVT
changes.
Table 1–13. OCT Without Calibration Resistance Tolerance Specifications for Arria II GZ Devices
Resistance Tolerance
Symbol
Description
Conditions (V)
Unit
C3,I3
C4,I4
25- RS
3.0 and 2.5
25-internal series
OCT without
calibration
VCCIO = 3.0, 2.5
± 40
± 40
%
25- RS
1.8 and 1.5
25- internal series
OCT without
calibration
VCCIO = 1.8, 1.5
± 40
± 40
%
25- RS
1.2
25-internal series
OCT without
calibration
VCCIO = 1.2
± 50
± 50
%
50- RS
3.0 and 2.5
50- internal series
OCT without
calibration
VCCIO = 3.0, 2.5
± 40
± 40
%
50- RS
1.8 and 1.5
50-internal series
OCT without
calibration
VCCIO = 1.8, 1.5
± 40
± 40
%
50- RS
1.2
50-internal series
OCT without
calibration
VCCIO = 1.2
± 50
± 50
%
100- RD
2.5
100-internal
differential OCT
VCCIO = 2.5
± 25
± 25
%
OCT calibration is automatically performed at power up for OCT-enabled I/Os.
When voltage and temperature conditions change after calibration, the resistance may
change. Use Equation 1–1 and Table 1–14 to determine the OCT variation when
voltage and temperature vary after power-up calibration for Arria II GX and GZ
devices.
Equation 1–1. OCT Variation (Note 1)
dR
dR
R OCT = R SCAL  1 +  -------  T   -------  V


dT
dV
Notes to Equation 1–1:
(1) ROCT value calculated from Equation 1–1shows the range of OCT resistance with the variation of temperature and
VCCIO.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–12
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Use the following with Equation 1–1:
■
RSCAL is the OCT resistance value at power up.
■
T is the variation of temperature with respect to the temperature at power up.
■
V is the variation of voltage with respect to the VCCIO at power up.
■
dR/dT is the percentage change of RSCAL with temperature.
■
dR/dV is the percentage change of RSCAL with voltage.
Table 1–14 lists the OCT variation with temperature and voltage after power-up
calibration for Arria II GX devices.
Table 1–14. OCT Variation after Power-up Calibration for Arria II GX Devices
Nominal Voltage VCCIO (V)
dR/dT (%/°C)
dR/dV (%/mV)
3.0
0.262
0.035
2.5
0.234
0.039
1.8
0.219
0.086
1.5
0.199
0.136
1.2
0.161
0.288
Table 1–15 lists the OCT variation with temperature and voltage after power-up
calibration for Arria II GZ devices.
Table 1–15. OCT Variation after Power-Up Calibration for Arria II GZ Devices (Note 1)
Nominal Voltage, VCCIO (V)
dR/dT (%/°C)
dR/dV (%/mV)
3.0
0.189
0.0297
2.5
0.208
0.0344
1.8
0.266
0.0499
1.5
0.273
0.0744
1.2
0.317
0.1241
Note to Table 1–15:
(1) Valid for VCCIO range of ±5% and temperature range of 0° to 85°C.
Pin Capacitance
Table 1–16 lists the pin capacitance for Arria II GX devices.
Table 1–16. Pin Capacitance for Arria II GX Devices
Symbol
CIO
Description
Input capacitance on I/O pins, dual-purpose pins (differential I/O, clock,
Rup, Rdn), and dedicated clock input pins
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Typical
Unit
7
pF
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–13
Table 1–17 lists the pin capacitance for Arria II GZ devices.
Table 1–17. Pin Capacitance for Arria II GZ Devices
Symbol
Description
Typical
Unit
CIOTB
Input capacitance on the top and bottom I/O pins
4
pF
CIOLR
Input capacitance on the left and right I/O pins
4
pF
CCLKTB
Input capacitance on the top and bottom non-dedicated clock input pins
4
pF
CCLKLR
Input capacitance on the left and right non-dedicated clock input pins
4
pF
COUTFB
Input capacitance on the dual-purpose clock output and feedback pins
5
pF
CCLK1, CCLK3, CCLK8,
and CCLK10
Input capacitance for dedicated clock input pins
2
pF
Internal Weak Pull-Up and Weak Pull-Down Resistors
Table 1–18 lists the weak pull-up and pull-down resistor values for Arria II GX
devices.
Table 1–18. Internal Weak Pull-up and Weak Pull-Down Resistors for Arria II GX Devices
Symbol
RPU
RPD
Description
Value of I/O pin pull-up resistor
before and during configuration,
as well as user mode if the
programmable pull-up resistor
option is enabled.
Value of TCK pin pull-down
resistor
Conditions
(Note 1)
Min
Typ
Max
Unit
VCCIO = 3.3 V ±5% (2)
7
25
41
k
VCCIO = 3.0 V ±5% (2)
7
28
47
k
VCCIO = 2.5 V ±5% (2)
8
35
61
k
VCCIO = 1.8 V ±5% (2)
10
57
108
k
VCCIO = 1.5 V ±5% (2)
13
82
163
k
VCCIO = 1.2 V ±5% (2)
19
143
351
k
VCCIO = 3.3 V ±5%
6
19
29
k
VCCIO = 3.0 V ±5%
6
22
32
k
VCCIO = 2.5 V ±5%
6
25
42
k
VCCIO = 1.8 V ±5%
7
35
70
k
VCCIO = 1.5 V ±5%
8
50
112
k
Notes to Table 1–18:
(1) All I/O pins have an option to enable weak pull-up except configuration, test, and JTAG pins. The weak pull-down feature is only available for
JTAG TCK.
(2) Pin pull-up resistance values may be lower if an external source drives the pin higher than VCCIO.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–14
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–19 lists the weak pull-up resistor values for Arria II GZ devices.
Table 1–19. Internal Weak Pull-Up Resistor for Arria II GZ Devices
Symbol
RPU
Description
Value of the I/O pin pull-up
resistor before and during
configuration, as well as user
mode if the programmable
pull-up resistor option is enabled.
(Note 1), (2)
Conditions
Min
Typ
Max
Unit
VCCIO = 3.0 V ±5% (3)
—
25
—
k
VCCIO = 2.5 V ±5% (3)
—
25
—
k
VCCIO = 1.8 V ±5% (3)
—
25
—
k
VCCIO = 1.5 V ±5% (3)
—
25
—
k
VCCIO = 1.2 V ±5% (3)
—
25
—
k
Notes to Table 1–19:
(1) All I/O pins have an option to enable weak pull-up except configuration, test, and JTAG pins.
(2) The internal weak pull-down feature is only available for the JTAG TCK pin. The typical value for this internal weak pull-down resistor is
approximately 25 k 
(3) Pin pull-up resistance values may be lower if an external source drives the pin higher than VCCIO.
Hot Socketing
Table 1–20 lists the hot-socketing specification for Arria II GX and GZ devices.
Table 1–20. Hot Socketing Specifications for Arria II Devices
Symbol
Description
Maximum
IIIOPIN(DC)
DC current per I/O pin
300 A
IIOPIN(AC)
AC current per I/O pin
8 mA (1)
IXCVRTX(DC)
DC current per transceiver TX pin
100 mA
IXCVRRX(DC)
DC current per transceiver RX pin
50 mA
Note to Table 1–20:
(1) The I/O ramp rate is 10 ns or more. For ramp rates faster than 10 ns, |IIOPIN| = C dv/dt, in which “C” is I/O pin
capacitance and “dv/dt” is slew rate.
Schmitt Trigger Input
The Arria II GX device supports Schmitt trigger input on the TDI, TMS, TCK, nSTATUS,
nCONFIG, nCE, CONF_DONE, and DCLK pins. A Schmitt trigger feature introduces
hysteresis to the input signal for improved noise immunity, especially for signals with
slow edge rates.
Table 1–21 lists the hysteresis specifications across the supported VCCIO range for
Schmitt trigger inputs in Arria II GX devices.
Table 1–21. Schmitt Trigger Input Hysteresis Specifications for Arria II GX Devices
Symbol
VSchmitt
Description
Hysteresis for Schmitt trigger input
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Condition (V)
Minimum
Unit
VCCIO = 3.3
220
mV
VCCIO = 2.5
180
mV
VCCIO = 1.8
110
mV
VCCIO = 1.5
70
mV
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–15
I/O Standard Specifications
Table 1–22 through Table 1–35 list input voltage (VIH and VIL), output voltage (VOH
and VOL), and current drive characteristics (IOH and IOL) for various I/O standards
supported by the Arria II device family. They also show the Arria II device family I/O
standard specifications. VOL and VOH values are valid at the corresponding IOH and
IOL, respectively.
1
For an explanation of terms used in Table 1–22 through Table 1–35, refer to “Glossary”
on page 1–74.
Table 1–22 lists the single-ended I/O standards for Arria II GX devices.
Table 1–22. Single-Ended I/O Standards for Arria II GX Devices
VCCIO (V)
VIL (V)
VIH (V)
VOL (V)
VOH (V)
IOH
(mA)
Min
Typ
Max
Min
Max
Min
Max
Max
Min
IOL
(mA)
3.3 V LVTTL
3.135
3.3
3.465
–0.3
0.8
1.7
3.6
0.45
2.4
4
–4
3.3 V LVCMOS
3.135
3.3
3.465
–0.3
0.8
1.7
3.6
0.2
VCCIO -0.2
2
–2
0.45
2.4
4
–4
I/O Standard
3.0 V LVTTL
2.85
3
3.15
–0.3
0.8
1.7
VCCIO +
0.3
3.0 V LVCMOS
2.85
3
3.15
–0.3
0.8
1.7
VCCIO +
0.3
0.2
VCCIO - 0.2
0.1
–0.1
2.5 V LVCMOS
2.375
2.5
2.625
–0.3
0.7
1.7
VCCIO +
0.3
0.4
2
1
–1
1.8 V LVCMOS
1.71
1.8
1.89
–0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.45
VCCIO 0.45
2
–2
1.5 V LVCMOS
1.425
1.5
1.575
–0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.25 ×
VCCIO
0.75 ×
VCCIO
2
–2
1.2 V LVCMOS
1.14
1.2
1.26
–0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.25 ×
VCCIO
0.75 ×
VCCIO
2
–2
3.0-V PCI
2.85
3
3.15
—
0.3 ×
VCCIO
0.5 ×
VCCIO
VCCIO +
0.3
0.1 ×
VCCIO
0.9 × VCCIO
1.5
–0.5
3.0-V PCI-X
2.85
3
3.15
—
0.35 ×
VCCIO
0.5 ×
VCCIO
VCCIO +
0.3
0.1 ×
VCCIO
0.9 × VCCIO
1.5
–0.5
Table 1–23 lists the single-ended I/O standards for Arria II GZ devices.
Table 1–23. Single-Ended I/O Standards for Arria II GZ Devices (Part 1 of 2)
VCCIO (V)
VIL (V)
VIH (V)
VOL (V)
VOH (V)
IOH
(mA)
Min
Typ
Max
Min
Max
Min
Max
Max
Min
IOL
(mA)
LVTTL
2.85
3
3.15
-0.3
0.8
1.7
3.6
0.4
2.4
2
-2
LVCMOS
2.85
3
3.15
-0.3
0.8
1.7
3.6
0.2
VCCIO - 0.2
0.1
-0.1
2.5 V
2.375
2.5
2.625
-0.3
0.7
1.7
3.6
0.4
2
1
-1
1.8 V
1.71
1.8
1.89
-0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.45
VCCIO 0.45
2
-2
1.5 V
1.425
1.5
1.575
-0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.25 ×
VCCIO
0.75 ×
VCCIO
2
-2
I/O Standard
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–16
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–23. Single-Ended I/O Standards for Arria II GZ Devices (Part 2 of 2)
VCCIO (V)
I/O Standard
VIL (V)
VIH (V)
VOL (V)
VOH (V)
IOL
(mA)
IOH
(mA)
Min
Typ
Max
Min
Max
Min
Max
Max
Min
1.2 V
1.14
1.2
1.26
-0.3
0.35 ×
VCCIO
0.65 ×
VCCIO
VCCIO +
0.3
0.25 ×
VCCIO
0.75 ×
VCCIO
2
-2
3.0-V PCI
2.85
3
3.15
—
0.3 ×
VCCIO
0.5 ×
VCCIO
3.6
0.1 ×
VCCIO
0.9 × VCCIO
1.5
-0.5
3.0-V PCI-X
2.85
3
3.15
—
0.35 ×
VCCIO
0.5 ×
VCCIO
—
0.1 ×
VCCIO
0.9 × VCCIO
1.5
-0.5
Table 1–24 lists the single-ended SSTL and HSTL I/O reference voltage specifications
for Arria II GX devices.
Table 1–24. Single-Ended SSTL and HSTL I/O Reference Voltage Specifications for Arria II GX Devices
VCCIO (V)
I/O Standard
VREF (V)
VTT (V)
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
SSTL-2 Class I, II
2.375
2.5
2.625
0.49 ×
VCCIO
0.5 × VCCIO
0.51 ×
VCCIO
VREF 0.04
VREF
VREF +
0.04
SSTL-18 Class I, II
1.71
1.8
1.89
0.833
0.9
0.969
VREF 0.04
VREF
VREF +
0.04
SSTL-15 Class I, II
1.425
1.5
1.575
0.47 ×
VCCIO
0.5 × VCCIO
0.53 ×
VCCIO
0.47 ×
VCCIO
0.5 ×
VCCIO
0.53 ×
VCCIO
HSTL-18 Class I, II
1.71
1.8
1.89
0.85
0.9
0.95
0.85
0.9
0.95
HSTL-15 Class I, II
1.425
1.5
1.575
0.71
0.75
0.79
0.71
0.75
0.79
HSTL-12 Class I, II
1.14
1.2
1.26
0.48 ×
VCCIO
0.5 × VCCIO
0.52 ×
VCCIO
—
VCCIO/2
—
Table 1–25 lists the single-ended SSTL and HSTL I/O reference voltage specifications
for Arria II GZ devices.
Table 1–25. Single-Ended SSTL and HSTL I/O Reference Voltage Specifications for Arria II GZ Devices
VCCIO (V)
I/O Standard
VREF (V)
VTT (V)
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
SSTL-2 Class I, II
2.375
2.5
2.625
0.49 ×
VCCIO
0.5 × VCCIO
0.51 ×
VCCIO
VREF 0.04
VREF
VREF +
0.04
SSTL-18 Class I, II
1.71
1.8
1.89
0.833
0.9
0.969
VREF 0.04
VREF
VREF +
0.04
SSTL-15 Class I, II
1.425
1.5
1.575
0.47 ×
VCCIO
0.5 × VCCIO
0.53 ×
VCCIO
0.47 ×
VCCIO
VREF
0.53 ×
VCCIO
HSTL-18 Class I, II
1.71
1.8
1.89
0.85
0.9
0.95
—
VCCIO/2
—
HSTL-15 Class I, II
1.425
1.5
1.575
0.68
0.75
0.9
—
VCCIO/2
—
1.26
0.47 ×
VCCIO
0.5 × VCCIO
0.53 ×
VCCIO
—
VCCIO/2
—
HSTL-12 Class I, II
1.14
1.2
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–17
Table 1–26 lists the single-ended SSTL and HSTL I/O standard signal specifications
for Arria II GX devices.
Table 1–26. Single-Ended SSTL and HSTL I/O Standard Signal Specifications for Arria II GX Devices
VIL(DC) (V)
I/O Standard
VIH(DC) (V)
VIL(AC) (V)
VIH(AC) (V)
VOL (V)
VOH (V)
IOL
(mA)
IOH
(mA)
Min
Max
Min
Max
Max
Min
Max
Min
SSTL-2 Class I
–0.3
VREF 0.18
VREF +
0.18
VCCIO +
0.3
VREF - 0.35
VREF +
0.35
VTT 0.57
VTT +
0.57
8.1
–8.1
SSTL-2 Class II
–0.3
VREF 0.18
VREF +
0.18
VCCIO +
0.3
VREF - 0.35
VREF +
0.35
VTT 0.76
VTT +
0.76
16.4
–16.4
SSTL-18 Class I
–0.3
VREF 0.125
VREF +
0.125
VCCIO +
0.3
VREF - 0.25
VREF +
0.25
VTT 0.475
VTT +
0.475
6.7
–6.7
SSTL-18 Class II
–0.3
VREF 0.125
VREF +
0.125
VCCIO +
0.3
VREF - 0.25
VREF +
0.25
0.28
VCCIO 0.28
13.4
–13.4
SSTL-15 Class I
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.175
VREF +
0.175
0.2 ×
VCCIO
0.8 ×
VCCIO
8
–8
SSTL-15 Class II
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.175
VREF +
0.175
0.2 ×
VCCIO
0.8 ×
VCCIO
16
–16
HSTL-18 Class I
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
8
–8
HSTL-18 Class II
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
16
–16
HSTL-15 Class I
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
8
–8
HSTL-15 Class II
–0.3
VREF 0.1
VREF +
0.1
VCCIO +
0.3
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
16
–16
HSTL-12 Class I
–0.15
VREF 0.08
VREF +
0.08
VCCIO +
0.15
VREF - 0.15
VREF +
0.15
0.25 ×
VCCIO
0.75 ×
VCCIO
8
–8
HSTL-12 Class II
–0.15
VREF 0.08
VREF +
0.08
VCCIO +
0.15
VREF - 0.15
VREF +
0.15
0.25 ×
VCCIO
0.75 ×
VCCIO
14
–14
Table 1–27 lists the single-ended SSTL and HSTL I/O standard signal specifications
for Arria II GZ devices.
Table 1–27. Single-Ended SSTL and HSTL I/O Standards Signal Specifications for Arria II GZ Devices (Part 1 of 2)
I/O Standard
VIL(DC) (V)
VIH(DC) (V)
VIL(AC) (V)
VIH(AC) (V)
VOL (V)
VOH (V)
IOL
(mA)
IOH
(mA)
Min
Max
Min
Max
Max
Min
Max
Min
SSTL-2 Class I
-0.3
VREF 0.15
VREF +
0.15
VCCIO +
0.3
VREF 0.31
VREF +
0.31
VTT 0.57
VTT +
0.57
8.1
-8.1
SSTL-2 Class II
-0.3
VREF 0.15
VREF +
0.15
VCCIO +
0.3
VREF 0.31
VREF +
0.31
VTT 0.76
VTT +
0.76
16.2
-16.2
SSTL-18 Class I
-0.3
VREF 0.125
VREF +
0.125
VCCIO +
0.3
VREF 0.25
VREF +
0.25
VTT 0.475
VTT +
0.475
6.7
-6.7
SSTL-18 Class II
-0.3
VREF 0.125
VREF +
0.125
VCCIO +
0.3
VREF 0.25
VREF +
0.25
0.28
VCCIO 0.28
13.4
-13.4
SSTL-15 Class I
—
VREF 0.1
VREF +
0.1
—
VREF 0.175
VREF +
0.175
0.2 ×
VCCIO
0.8 ×
VCCIO
8
-8
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–18
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–27. Single-Ended SSTL and HSTL I/O Standards Signal Specifications for Arria II GZ Devices (Part 2 of 2)
VIL(DC) (V)
I/O Standard
VIH(DC) (V)
VIL(AC) (V)
VIH(AC) (V)
VOL (V)
VOH (V)
IOL
(mA)
IOH
(mA)
Min
Max
Min
Max
Max
Min
Max
Min
SSTL-15 Class II
—
VREF 0.1
VREF +
0.1
—
VREF 0.175
VREF +
0.175
0.2 ×
VCCIO
0.8 ×
VCCIO
16
-16
HSTL-18 Class I
—
VREF 0.1
VREF +
0.1
—
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
8
-8
HSTL-18 Class II
—
VREF 0.1
VREF +
0.1
—
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
16
-16
HSTL-15 Class I
—
VREF 0.1
VREF +
0.1
—
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
8
-8
HSTL-15 Class II
—
VREF 0.1
VREF +
0.1
—
VREF - 0.2
VREF + 0.2
0.4
VCCIO 0.4
16
-16
HSTL-12 Class I
-0.15
VREF 0.08
VREF +
0.08
VCCIO +
0.15
VREF 0.15
VREF +
0.15
0.25×
VCCIO
0.75×
VCCIO
8
-8
HSTL-12 Class II
-0.15
VREF 0.08
VREF +
0.08
VCCIO +
0.15
VREF 0.15
VREF +
0.15
0.25×
VCCIO
0.75 ×
VCCIO
16
-16
Table 1–28 lists the differential SSTL I/O standards for Arria II GX devices.
Table 1–28. Differential SSTL I/O Standards for Arria II GX Devices
VCCIO (V)
I/O Standard
VSWING(DC) (V)
VX(AC) (V)
VSWING(AC) (V)
VOX(AC) (V)
Min
Typ
Max
Min
Max
Min
Typ
Max
Min
Max
Min
Typ
Max
SSTL-2 Class I, II
2.375
2.5
2.625
0.36
VCCIO
VCCIO/2
- 0.2
—
VCCIO/2
+ 0.2
0.7
VCCIO
VCCIO/2
- 0.15
—
VCCIO/2
+ 0.15
SSTL-18 Class I, II
1.71
1.8
1.89
0.25
VCCIO
VCCIO/2
- 0.175
—
VCCIO/2
+ 0.175
0.5
VCCIO
VCCIO/2
0.125
—
VCCIO/2
+
0.125
SSTL-15 Class I, II
1.425
1.5
1.575
0.2
—
—
VCCIO/
2
—
0.35
—
—
VCCIO/
2
—
Table 1–29 lists the differential SSTL I/O standards for Arria II GZ devices
Table 1–29. Differential SSTL I/O Standards for Arria II GZ Devices
VCCIO (V)
I/O Standard
VSWING(DC) (V)
VX(AC) (V)
VSWING(AC) (V)
VOX(AC) (V)
Min
Typ
Max
Min
Max
Min
Typ
Max
Min
Max
Min
Typ
Max
SSTL-2 Class I, II
2.375
2.5
2.625
0.3
VCCIO
+ 0.6
VCCIO/2
- 0.2
—
VCCIO/2
+ 0.2
0.62
VCCIO
+ 0.6
VCCIO/2
- 0.15
—
VCCIO/2
+ 0.15
SSTL-18 Class I, II
1.71
1.8
1.89
0.25
VCCIO
+ 0.6
VCCIO/2
0.175
—
VCCIO/2
+
0.175
0.5
VCCIO
+ 0.6
VCCIO/2
- 0.125
—
VCCIO/2
+ 0.125
SSTL-15 Class I, II
1.425
1.5
1.575
0.2
—
—
VCCIO/
2
—
0.35
—
—
VCCIO/
2
—
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
1–19
Table 1–30 lists the HSTL I/O standards for Arria II GX devices.
Table 1–30. Differential HSTL I/O Standards for Arria II GX Devices
VCCIO (V)
I/O Standard
VDIF(DC) (V)
VX(AC) (V)
VCM(DC) (V)
VDIF(AC) (V)
Min
Typ
Max
Min
Max
Min
Typ
Max
Min
Typ
Max
Min
Max
HSTL-18 Class I
1.71
1.8
1.89
0.2
—
0.85
—
0.95
0.88
—
0.95
0.4
—
HSTL-15 Class I, II
1.425
1.5
1.575
0.2
—
0.71
—
0.79
0.71
—
0.79
0.4
—
HSTL-12 Class I, II
1.14
1.2
1.26
0.16
—
—
0.5 ×
VCCIO
—
0.48
×
VCCIO
0.5 ×
VCCIO
0.52 ×
VCCIO
0.3
—
Table 1–31 lists the HSTL I/O standards for Arria II GZ devices.
Table 1–31. Differential HSTL I/O Standards for Arria II GZ Devices
VCCIO (V)
I/O Standard
VDIF(DC) (V)
VX(AC) (V)
VCM(DC) (V)
VDIF(AC) (V)
Min
Typ
Max
Min
Max
Min
Typ
Max
Min
Typ
Max
Min
Max
HSTL-18 Class I
1.71
1.8
1.89
0.2
—
0.78
—
1.12
0.78
—
1.12
0.4
—
HSTL-15 Class I, II
1.425
1.5
1.575
0.2
—
0.68
—
0.9
0.68
—
0.9
0.4
—
HSTL-12 Class I, II
1.14
1.2
1.26
0.16
VCCIO
+ 0.3
—
0.5 ×
VCCIO
—
0.4 ×
VCCIO
0.5 ×
VCCIO
0.6 ×
VCCIO
0.3
VCCIO
+
0.48
Table 1–32 lists the differential I/O standard specifications for Arria II GX devices.
Table 1–32. Differential I/O Standard Specifications for Arria II GX Devices (Note 1)
I/O
Standard
VCCIO (V)
VID (mV)
VICM (V) (2)
VOD (V) (3)
VOCM (V)
Min
Typ
Max
Min
Cond.
Max
Min
Max
Min
Typ
Max
Min
Typ
Max
2.5 V
LVDS
2.375
2.5
2.625
100
VCM =
1.25 V
—
0.05
1.80
0.247
—
0.6
1.125
1.25
1.375
RSDS (4)
2.375
2.5
2.625
—
—
—
—
—
0.1
0.2
0.6
0.5
1.2
1.4
Mini-LVDS
(4)
2.375
2.5
2.625
—
—
—
—
—
0.25
—
0.6
1
1.2
1.4
LVPECL
(5)
2.375
2.5
2.625
300
—
—
0.6
1.8
—
—
—
—
—
—
BLVDS (6)
2.375
2.5
2.625
100
—
—
—
—
—
—
—
—
—
—
Notes to Table 1–32:
(1) The 1.5 V PCML transceiver I/O standard specifications are described in “Transceiver Performance Specifications” on page 1–21.
(2) VIN range: 0 <= VIN <= 1.85 V.
(3) RL range: 90 <= RL <= 110  .
(4) The RSDS and mini-LVDS I/O standards are only supported for differential outputs.
(5) The LVPECL input standard is supported at the dedicated clock input pins (GCLK) only.
(6) There are no fixed VICM, VOD, and VOCM specifications for BLVDS. These specifications depend on the system topology.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–20
Chapter 1: Device Datasheet for Arria II Devices
Electrical Characteristics
Table 1–33 lists the differential I/O standard specifications for Arria II GZ devices.
Table 1–33. Differential I/O Standard Specifications for Arria II GZ Devices (Note 1)
I/O
Standard
(2)
VCCIO (V)
VID (mV)
VICM(DC) (V)
VOD (V) (3)
VOCM (V) (3)
Min
Typ
Max
Min
Cond.
Max
Min
Max
Min
Typ
Max
Min
Typ
Max
2.5 V
LVDS
(HIO)
2.375
2.5
2.625
100
VCM =
1.25 V
—
0.05
1.8
0.247
—
0.6
1.125
1.25
1.375
2.5 V
LVDS
(VIO)
2.375
2.5
2.625
100
VCM =
1.25 V
—
0.05
1.8
0.247
—
0.6
1
1.25
1.5
RSDS
(HIO)
2.375
2.5
2.625
100
VCM =
1.25 V
—
0.3
1.4
0.1
0.2
0.6
0.5
1.2
1.4
RSDS
(VIO)
2.375
2.5
2.625
100
VCM =
1.25 V
—
0.3
1.4
0.1
0.2
0.6
0.5
1.2
1.5
Mini-LVDS
(HIO)
2.375
2.5
2.625
200
—
600
0.4
1.32
5
0.25
—
0.6
1
1.2
1.4
Mini-LVDS
(VIO)
2.375
2.5
2.625
200
—
600
0.4
1.32
5
0.25
—
0.6
1
1.2
1.5
LVPECL
2.375
2.5
2.625
300
—
—
0.6
1.8
—
—
—
—
—
—
BLVDS (4)
2.375
2.5
2.625
100
—
—
—
—
—
—
—
—
—
—
Notes to Table 1–33:
(1) 1.4-V/1.5-V PCML transceiver I/O standard specifications are described in “Transceiver Performance Specifications” on page 1–21.
(2) Vertical I/O (VIO) is top and bottom I/Os; horizontal I/O (HIO) is left and right I/Os.
(3) RL range: 90  RL  110  .
(4) There are no fixed VICM, VOD, and VOCM specifications for BLVDS. These specifications depend on the system topology.
Power Consumption for the Arria II Device Family
Altera offers two ways to estimate power for a design:
■
Using the Microsoft Excel-based Early Power Estimator
■
Using the Quartus® II PowerPlay Power Analyzer feature
The interactive Microsoft Excel-based Early Power Estimator is typically used prior to
designing the FPGA in order to get a magnitude estimate of the device power. The
Quartus II PowerPlay Power Analyzer provides better quality estimates based on the
specifics of the design after place-and-route is complete. The PowerPlay Power
Analyzer can apply a combination of user-entered, simulation-derived, and estimated
signal activities which, when combined with detailed circuit models, can yield very
accurate power estimates.
f For more information about power estimation tools, refer to the PowerPlay Early Power
Estimator User Guide and the PowerPlay Power Analysis chapter in volume 3 of the
Quartus II Handbook.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Altera Corporation
This section provides performance characteristics of the Arria II GX and GZ core and periphery blocks for commercial grade
devices. The following tables are considered final and are based on actual silicon characterization and testing. These numbers
reflect the actual performance of the device under worst-case silicon process, voltage, and junction temperature conditions.
Transceiver Performance Specifications
Table 1–34 lists the Arria II GX transceiver specifications.
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 1 of 7)
Symbol/
Description
I3
C4
C5 and I5
C6
Condition
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012
Switching Characteristics
Reference Clock
Supported I/O
Standards
1.2-V PCML, 1.5-V PCML, 2.5-V PCML, Differential LVPECL, LVDS, and HCSL
—
50
—
622.08
50
—
622.08
50
—
622.08
50
—
622.08
MHz
Input frequency
from PLD input
—
50
—
200
50
—
200
50
—
200
50
—
200
MHz
Absolute VMAX
for a REFCLK pin
—
—
—
2.2
—
—
2.2
—
—
2.2
—
—
2.2
V
Absolute VMIN for
a REFCLK pin
—
–0.3
—
—
–0.3
—
—
–0.3
—
—
–0.3
—
—
V
Rise/fall time (2)
—
—
—
0.2
—
—
0.2
—
—
0.2
—
—
0.2
UI
Duty cycle
—
45
—
55
45
—
55
45
—
55
45
—
55
%
Peak-to-peak
differential input
voltage
—
200
—
2000
200
—
2000
200
—
2000
200
—
2000
mV
30
—
33
30
—
33
30
—
33
30
—
33
kHz
Spread-spectrum
modulating clock PCIe
frequency
1–21
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Input frequency
from REFCLK
input pins
I3
Altera Corporation
Symbol/
Description
C4
C5 and I5
C6
Condition
Spread-spectrum
PCIe
downspread
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
—
0 to
–0.5%
—
—
0 to
–0.5%
—
—
0 to
–0.5%
—
—
0 to
–0.5%
—
—
—
100
—
—
100
—
—
100
—
—
100
—

—
VICM
(AC coupled)
—
VICM
(DC coupled)
HCSL I/O
standard for
PCIe
reference
clock
250
—
550
250
—
550
250
—
550
250
—
550
mV
10 Hz
—
—
-50
—
—
-50
—
—
-50
—
—
-50
dBc/Hz
100 Hz
—
—
-80
—
—
-80
—
—
-80
—
—
-80
dBc/Hz
1 KHz
—
—
-110
—
—
-110
—
—
-110
—
—
-110
dBc/Hz
10 KHz
—
—
-120
—
—
-120
—
—
-120
—
—
-120
dBc/Hz
100 KHz
—
—
-120
—
—
-120
—
—
-120
—
—
-120
dBc/Hz
1 MHz
—
—
-130
—
—
-130
—
—
-130
—
—
-130
dBc/Hz
—
—
3
—
—
3
—
—
3
—
—
3
ps
—
—
2000
± 1%
—
—
2000
± 1%
—
—
2000
± 1%
—
—
2000 ±
1%
—

—
10
—
125
10
—
125
10
—
125
10
—
125
MHz
Transmitter
REFCLK Phase
Noise
Transmitter
REFCLK Phase
Jitter (rms) for
100 MHz
REFCLK (3)
Rref
10 KHz to
20 MHz
1100 ± 5%
1100 ± 5%
1100 ± 5%
1100 ± 5%
mV
Transceiver Clocks
Calibration block
clock frequency
(cal_blk_clk)
1–22
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
On-chip
termination
resistors
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 2 of 7)
Altera Corporation
Symbol/
Description
I3
C4
C5 and I5
C6
Condition
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
fixedclk clock
frequency
PCIe
Receiver
Detect
—
125
—
—
125
—
—
125
—
—
125
—
MHz
reconfig_
clk clock
frequency
Dynamic
reconfig.
clock
frequency
2.5/
37.5
(4)
—
50
2.5/
37.5
(4)
—
50
2.5/
37.5
(4)
—
50
2.5/
37.5
(4)
—
50
MHz
Delta time
between
reconfig_
clks (5)
—
—
—
2
—
—
2
—
—
2
—
—
2
ms
Transceiver block
minimum
power-down
pulse width
—
—
1
—
—
1
—
—
1
—
—
1
—
µs
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 3 of 7)
Supported I/O
Standards
1.4-V PCML, 1.5-V PCML, 2.5-V PCML, 2.5-V PCML, LVPECL, and LVDS
Data rate
—
600
—
6375
600
—
3750
600
—
3750
600
—
3125
Mbps
Absolute VMAX
for a receiver pin
(6)
—
—
—
1.5
—
—
1.5
—
—
1.5
—
—
1.5
V
Absolute VMIN for
a receiver pin
—
-0.4
—
—
-0.4
—
—
-0.4
—
—
-0.4
—
—
V
VICM = 0.82 V
setting
—
—
2.7
—
—
2.7
—
—
2.7
—
—
2.7
V
VICM =1.1 V
setting (7)
—
—
1.6
—
—
1.6
—
—
1.6
—
—
1.6
V
Maximum
peak-to-peak
differential input
voltage VID (diff
p-p)
1–23
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Receiver
I3
Symbol/
Description
Condition
Minimum
peak-to-peak
differential input
voltage VID (diff
p-p)
VICM
Differential
on-chip
termination
resistors
1–24
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 4 of 7)
C4
C5 and I5
C6
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
—
100
—
—
100
—
—
100
—
—
100
—
—
mV
VICM = 0.82 V
setting
—
820
—
—
820
—
—
820
—
—
820
—
mV
VICM =1.1 V
setting (7)
—
1100
—
—
1100
—
—
1100
—
—
1100
—
mV
100
setting
—
100
—
—
100
—
—
100
—
—
100
—

Return loss
differential mode
PCIe
50 MHz to 1.25 GHz: –10dB
XAUI
100 MHz to 2.5 GHz: –10dB
Return loss
common mode
PCIe
50 MHz to 1.25 GHz: –6dB
XAUI
100 MHz to 2.5 GHz: –6dB
—
Run length
—
—
80
—
—
80
—
—
80
—
—
80
—
UI
Programmable
equalization
—
—
—
7
—
—
7
—
—
7
—
—
7
dB
65
—
175
65
—
175
65
—
175
65
—
175
mV
75
—
—
75
—
—
75
µs
15
—
—
15
—
—
µs
Signal
detect/loss
threshold
PCIe Mode
± 62.5, 100, 125, 200,
ppm
250, 300, 500, 1000
CDR LTR time
(9)
—
—
—
75
—
—
CDR minimum
T1b (10)
—
15
—
—
15
—
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012 Altera Corporation
Programmable
PPM detector
(8)
Altera Corporation
Symbol/
Description
I3
C4
C5 and I5
C6
Condition
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
LTD lock time
(11)
—
0
100
4000
0
100
4000
0
100
4000
0
100
4000
ns
Data lock time
from rx_
freqlocked
(12)
—
—
—
4000
—
—
4000
—
—
4000
—
—
4000
ns
DC Gain
Setting = 0
—
0
—
—
0
—
—
0
—
—
0
—
dB
DC Gain
Setting = 1
—
3
—
—
3
—
—
3
—
—
3
—
dB
DC Gain
Setting = 2
—
6
—
—
6
—
—
6
—
—
6
—
dB
Programmable
DC gain
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 5 of 7)
Transmitter
1.5-V PCML
Data rate
—
600
—
6375
600
—
3750
600
—
3750
600
—
3125
Mbps
VOCM
0.65 V
setting
—
650
—
—
650
—
—
650
—
—
650
—
mV
Differential
on-chip
termination
resistors
100
setting
—
100
—
—
100
—
—
100
—
—
100
—

Return loss
differential mode
Return loss
common mode
PCIe
50 MHz to 1.25 GHz: –10dB
XAUI
312 MHz to 625 MHz: –10dB
625 MHz to 3.125 GHz: –10dB/decade slope
PCIe
50 MHz to 1.25 GHz: –6dB
Rise time (2)
—
50
—
200
50
—
200
50
—
200
50
—
200
ps
Fall time
—
50
—
200
50
—
200
50
—
200
50
—
200
ps
1–25
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Supported I/O
Standards
Symbol/
Description
I3
1–26
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 6 of 7)
C4
C5 and I5
C6
Condition
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
—
—
—
15
—
—
15
—
—
15
—
—
15
ps
Intra-transceiver
block skew
PCIe ×4
—
—
120
—
—
120
—
—
120
—
—
120
ps
Inter-transceiver
block skew
PCIe ×8
—
—
300
—
—
300
—
—
300
—
—
300
ps
—
—
100
—
—
100
—
—
100
—
—
100
s
25
—
320
25
—
240
25
—
240
25
—
200
MHz
Intradifferential pair
skew
CMU PLL0 and CMU PLL1
CMU PLL lock
time from
CMUPLL_
reset
deassertion
—
PLD-Transceiver Interface
Interface speed
—
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012 Altera Corporation
Altera Corporation
Symbol/
Description
Digital reset
pulse width
I3
C4
C5 and I5
C6
Condition
Unit
Min
Typ
Max
—
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Minimum is 2 parallel clock cycles
Notes to Table 1–34:
(1) For AC-coupled links, the on-chip biasing circuit is switched off before and during configuration. Ensure that input specifications are not violated during this period.
(2) The rise/fall time is specified from 20% to 80%.
(3) To calculate the REFCLK rms phase jitter requirement at reference clock frequencies other than 100 MHz, use the following formula:
REFCLK rms phase jitter at f (MHz) = REFCLK rms phase jitter at 100 MHz * 100/f.
(4) The minimum reconfig_clk frequency is 2.5 MHz if the transceiver channel is configured in Transmitter only mode. The minimum reconfig_clk frequency is 37.5 MHz if the transceiver channel is
configured in Receiver only or Receiver and Transmitter mode. For more information, refer to AN 558: Implementing Dynamic Reconfiguration in Arria II Devices.
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
July 2012
Table 1–34. Transceiver Specifications for Arria II GX Devices (Note 1) (Part 7 of 7)
(5) If your design uses more than one dynamic reconfiguration controller instances (altgx_reconfig) to control the transceiver channels (altgx) physically located on the same side of the device, and if
you use different reconfig_clk sources for these altgx_reconfig instances, the delta time between any two of these reconfig_clk sources becoming stable must not exceed the maximum
specification listed.
(6) The device cannot tolerate prolonged operation at this absolute maximum.
(7) You must use the 1.1-V RX VICM setting if the input serial data standard is LVDS and the link is DC-coupled.
(8) The rate matcher supports only up to ±300 parts per million (ppm).
(9) Time taken to rx_pll_locked goes high from rx_analogreset de-assertion. Refer to Figure 1–1.
(10) The time in which the CDR must be kept in lock-to-reference mode after rx_pll_locked goes high and before rx_locktodata is asserted in manual mode. Refer to Figure 1–1.
(12) The time taken to recover valid data after the rx_freqlocked signal goes high in automatic mode. Refer to Figure 1–2.
1–27
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
(11) The time taken to recover valid data after the rx_locktodata signal is asserted in manual mode. Refer to Figure 1–1.
1–28
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–35 lists the transceiver specifications for Arria II GZ devices.
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 1 of 5)
Symbol/
Description
–C3 and –I3 (1)
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Reference Clock
Supported I/O Standards
1.2-V PCML, 1.5-V PCML, 2.5-V PCML, Differential LVPECL, LVDS, and HCSL
Input frequency from
REFCLK input pins
—
50
—
697
50
—
637.5
MHz
Phase frequency detector
(CMU PLL and receiver
CDR)
—
50
—
325
50
—
325
MHz
Absolute VMAX for a REFCLK
pin
—
—
—
1.6
—
—
1.6
V
Operational VMAX for a
REFCLK pin
—
—
—
1.5
—
—
1.5
V
Absolute VMIN for a REFCLK
pin
—
-0.4
—
—
-0.4
—
—
V
Rise/fall time (2)
—
—
—
0.2
—
—
0.2
UI
Duty cycle
—
45
—
55
45
—
55
%
Peak-to-peak differential
input voltage
—
200
—
1600
200
—
1600
mV
Spread-spectrum
modulating clock frequency
PCIe
30
—
33
30
—
33
kHz
Spread-spectrum
downspread
PCIe
—
—
—
—
—
On-chip termination
resistors
—
—
—
—
—

VICM (AC coupled)
—
VICM (DC coupled)
HCSL I/O standard
for PCIe reference
clock
250
—
550
250
—
550
mV
10 Hz
—
—
-50
—
—
-50
dBc/Hz
100 Hz
—
—
-80
—
—
-80
dBc/Hz
1 KHz
—
—
-110
—
—
-110
dBc/Hz
10 KHz
—
—
-120
—
—
-120
dBc/Hz
100 KHz
—
—
-120
—
—
-120
dBc/Hz
 1 MHz
—
—
-130
—
—
-130
dBc/Hz
10 KHz to 20 MHz
—
—
3
—
—
3
ps
—
—
2000 ±
1%
—
—
2000 ±
1%
—

Transmitter REFCLK Phase
Noise
Transmitter REFCLK Phase
Jitter (rms) for 100 MHz
REFCLK (3)
RREF
0 to
-0.5%
100
1100 ± 10%
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
0 to
-0.5%
100
1100 ± 10%
mV
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–29
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 2 of 5)
Symbol/
Description
–C3 and –I3 (1)
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Transceiver Clocks
Calibration block clock
frequency (cal_blk_clk)
—
10
—
125
10
—
125
MHz
fixedclk clock frequency
PCIe Receiver
Detect
—
125
—
—
125
—
MHz
reconfig_clk clock
frequency
Dynamic
reconfiguration
clock frequency
2.5/
37.5
(4)
—
50
2.5/
37.5
(4)
—
50
MHz
Delta time between
reconfig_clks (5)
—
—
—
2
—
—
2
ms
Transceiver block minimum
power-down
(gxb_powerdown) pulse
width
—
1
—
—
1
—
—
µs
Receiver
Supported I/O Standards
1.4-V PCML, 1.5-V PCML, 2.5-V PCML, LVPECL, and LVDS
Data rate
—
600
—
6375
600
—
3750
Mbps
Absolute VMAX for a receiver
pin (6)
—
—
—
1.6
—
—
1.6
V
Operational VMAX for a
receiver pin
—
—
—
1.5
—
—
1.5
V
Absolute VMIN for a receiver
pin
—
-0.4
—
—
-0.4
—
—
V
Maximum peak-to-peak
differential input voltage VID
(diff p-p) before device
configuration
—
—
—
1.6
—
—
1.6
V
VICM = 0.82 V
setting
—
—
2.7
—
—
2.7
V
VICM =1.1 V setting
(7)
—
—
1.6
—
—
1.6
V
100
—
—
165
—
—
mV
165
—
—
165
—
—
mV
Maximum peak-to-peak
differential input voltage VID
(diff p-p) after device
configuration
Data Rate =
600 Mbps to
5 Gbps
Minimum differential eye
opening at receiver serial
input pins (8)
Equalization = 0
DC gain = 0 dB
Data Rate > 5 Gbps
Equalization = 0
DC gain = 0 dB
VICM
July 2012
Altera Corporation
VICM = 0.82 V
setting
820 ± 10%
820 ± 10%
mV
VICM = 1.1 V setting
(7)
1100 ± 10%
1100 ± 10%
mV
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–30
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 3 of 5)
Symbol/
Description
Receiver DC Coupling
Support
Differential on-chip
termination resistors
Differential and common
mode return loss
–C3 and –I3 (1)
–C4 and –I4
Conditions
Unit
Min
—
Typ
Max
Min
Typ
Max
For more information about receiver DC coupling support, refer to the
“DC-Coupled Links” section in the Transceiver Architecture for Arria II
Devices chapter.
85 setting
85 ± 20%
85 ± 20%

100 setting
100 ± 20%
100 ± 20%

120 setting
120 ± 20%
120 ± 20%

150- setting
150 ± 20%
150 ± 20%

PCIe (Gen 1 and
Gen 2),
XAUI,
HiGig+,
CEI SR/LR,
SRIO SR/LR,
Compliant
—
± 62.5, 100, 125, 200, 250, 300, 500, 1,000
ppm
CPRI LV/HV,
OBSAI,
SATA
Programmable PPM
detector (9)
—
Run length
—
—
—
200
—
—
200
UI
Programmable equalization
—
—
—
16
—
—
16
dB
tLTR (10)
—
—
—
75
—
—
75
µs
tLTR_LTD_Manual (11)
—
15
—
—
15
—
—
µs
tLTD_Manual (12)
—
—
—
4000
—
—
4000
ns
tLTD_Auto (13)
—
—
—
4000
—
—
4000
ns
Receiver CDR
3 dB Bandwidth in
lock-to-data (LTD) mode
Receiver buffer and CDR
offset cancellation time (per
channel)
Programmable DC gain
PCIe Gen1
2.0 - 3.5
MHz
PCIe Gen2
40 - 65
MHz
(OIF) CEI PHY at
6.375 Gbps
20 - 35
MHz
XAUI
10 - 18
MHz
SRIO 1.25 Gbps
10 - 18
MHz
SRIO 2.5 Gbps
10 - 18
MHz
SRIO 3.125 Gbps
6 - 10
MHz
GIGE
6 - 10
MHz
SONET OC12
3-6
MHz
SONET OC48
14 - 19
MHz
—
—
—
17000
—
—
17000
recon
fig_
clk
cycles
DC Gain Setting = 0
—
0
—
—
0
—
dB
DC Gain Setting = 1
—
3
—
—
3
—
dB
DC Gain Setting = 2
—
6
—
—
6
—
dB
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–31
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 4 of 5)
Symbol/
Description
–C3 and –I3 (1)
–C4 and –I4
Conditions
Unit
Min
Typ
—
600
—
0.65 V setting
—
650
Max
Min
Typ
Max
6375
600
—
3750
Mbps
—
—
650
—
mV
Transmitter
Supported I/O Standards
Data rate (14)
VOCM
Differential on-chip
termination resistors
Differential and common
mode return loss
1.5-V PCML
85 setting
85 ± 15%
85 ± 15%

100 setting
100 ± 15%
100 ± 15%

120 setting
120 ± 15%
120 ± 15%

150- setting
150 ± 15%
150 ± 15%

PCIe Gen1 and
Gen2 (TX VOD=4),
XAUI (TX VOD=6),
HiGig+
(TX VOD=6),
CEI SR/LR
(TX VOD=8),
SRIO SR (VOD=6),
SRIO LR (VOD=8),
CPRI LV (VOD=6),
CPRI HV (VOD=2),
OBSAI (VOD=6),
SATA (VOD=4),
Compliant
—
Rise time (15)
—
50
—
200
50
—
200
ps
Fall time (15)
—
50
—
200
50
—
200
ps
Intra-differential pair skew
—
—
—
15
—
—
15
ps
Intra-transceiver block
transmitter
channel-to-channel skew
×4 PMA and PCS
bonded mode
Example: XAUI,
PCIe ×4, Basic ×4
—
—
120
—
—
120
ps
Inter-transceiver block
transmitter
channel-to-channel skew
×8 PMA and PCS
bonded mode
Example: PCIe ×8,
Basic ×8
—
—
500
—
—
500
ps
600
—
6375
600
—
3750
Mbps
CMU0 PLL and CMU1 PLL
Supported Data Range
—
pll_powerdown minimum
pulse width
(tpll_powerdown)
—
CMU PLL lock time from
pll_powerdown
de-assertion
—
July 2012
Altera Corporation
1
—
—
s
1
100
—
—
100
s
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–32
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 5 of 5)
Symbol/
Description
–C3 and –I3 (1)
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
PCIe Gen1
2.5 - 3.5
MHz
PCIe Gen2
6-8
MHz
(OIF) CEI PHY at
4.976 Gbps
7 - 11
MHz
(OIF) CEI PHY at
6.375 Gbps
5 - 10
MHz
XAUI
2-4
MHz
SRIO 1.25 Gbps
3 - 5.5
MHz
SRIO 2.5 Gbps
3 - 5.5
MHz
-3 dB Bandwidth
SRIO 3.125 Gbps
2-4
MHz
GIGE
2.5 - 4.5
MHz
SONET OC12
1.5 - 2.5
MHz
SONET OC48
3.5 - 6
MHz
Transceiver-FPGA Fabric Interface
Interface speed
—
Digital reset pulse width
—
25
—
325
25
—
250
Minimum is two parallel clock cycles
MHz
—
Notes to Table 1–35:
(1) The 3x speed grade is the fastest speed grade offered in the following Arria II GZ devices: EP2AGZ225, EP2AGZ300, and EP2AGZ350.
(2) The rise and fall time transition is specified from 20% to 80%.
(3) To calculate the REFCLK rms phase jitter requirement at reference clock frequencies other than 100 MHz, use the following formula:
REFCLK rms phase jitter at f (MHz) = REFCLK rms phase jitter at 100 MHz * 100/f.
(4) The minimum reconfig_clk frequency is 2.5 MHz if the transceiver channel is configured in Transmitter only mode. The minimum
reconfig_clk frequency is 37.5 MHz if the transceiver channel is configured in Receiver only or Receiver and Transmitter mode.
(5) If your design uses more than one dynamic reconfiguration controller (altgx_reconfig) instances to control the transceiver (altgx)
channels physically located on the same side of the device AND if you use different reconfig_clk sources for these altgx_reconfig
instances, the delta time between any two of these reconfig_clk sources becoming stable must not exceed the maximum specification listed.
(6) The device cannot tolerate prolonged operation at this absolute maximum.
(7) You must use the 1.1-V RX VICM setting if the input serial data standard is LVDS.
(8) The differential eye opening specification at the receiver input pins assumes that Receiver Equalization is disabled. If you enable Receiver
Equalization, the receiver circuitry can tolerate a lower minimum eye opening, depending on the equalization level. Use H-Spice simulation to
derive the minimum eye opening requirement with Receiver Equalization enabled.
(9) The rate matcher supports only up to ± 300 ppm.
(10) Time taken to rx_pll_locked goes high from rx_analogreset de-assertion. Refer to Figure 1–1 on page 1–33.
(11) Time for which the CDR must be kept in lock-to-reference mode after rx_pll_locked goes high and before rx_locktodata is asserted in
manual mode. Refer to Figure 1–1 on page 1–33.
(12) Time taken to recover valid data after the rx_locktodata signal is asserted in manual mode. Refer to Figure 1–1 on page 1–33.
(13) Time taken to recover valid data after the rx_freqlocked signal goes high in automatic mode. Refer to Figure 1–2 on page 1–33.
(14) A GPLL may be required to meet the PMA-FPGA fabric interface timing above certain data rates. For more information, refer to the Transceiver
Clocking for Arria II Devices chapter.
(15) The Quartus II software automatically selects the appropriate slew rate depending on the configured data rate or functional mode.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–33
Figure 1–1 shows the lock time parameters in manual mode.
1
LTD = lock-to-data. LTR = lock-to-reference.
Figure 1–1. Lock Time Parameters for Manual Mode
r x_analogreset
CDR status
LTR
LTD
r x_pll_locked
r x_locktodata
Invalid Data
Valid data
r x_dataout
CDR LTR Time
LTD lock time
CDR Minimum T1b
Figure 1–2 shows the lock time parameters in automatic mode.
Figure 1–2. Lock Time Parameters for Automatic Mode
CDR status
LTR
LTD
r x_freqlocked
r x_dataout
Invalid
Valid
data
data
Data lock time from rx_freqlocked
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–34
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Figure 1–3 shows the differential receiver input waveform.
Figure 1–3. Receiver Input Waveform
Single-Ended Waveform
Positive Channel (p)
VID
Negative Channel (n)
VCM
Ground
Differential Waveform
VID (diff peak-peak) = 2 x VID (single-ended)
VID
p−n=0V
VID
Figure 1–4 shows the transmitter output waveform.
Figure 1–4. Transmitter Output Waveform
Single-Ended Waveform
Positive Channel (p)
VOD
Negative Channel (n)
VCM
Ground
Differential Waveform
VOD (diff peak-peak) = 2 x VOD (single-ended)
VOD
p−n=0V
VOD
Table 1–36 lists the typical VOD for TX term that equals 85 . for Arria II GZ devices.
Table 1–36. Typical VOD Setting, TX Term = 85 for Arria II GZ Devices
VOD Setting (mV)
Symbol
VOD differential
peak-to-peak Typical (mV)
0
1
2
3
4
5
6
7
170 ±
20%
340 ±
20%
510 ±
20%
595 ±
20%
680 ±
20%
765 ±
20%
850 ±
20%
1020 ±
20%
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–35
Table 1–37 lists the typical VOD for TX term that equals 100 . for Arria II GX and GZ
devices.
Table 1–37. Typical VOD Setting, TX Termination = 100  for Arria II Devices
Quartus II Setting
VOD Setting (mV)
1
400
2
600
3 (Arria II GZ)
700
4
800
5
900
6
1000
7
1200
Table 1–38 lists the typical transmitter pre-emphasis levels in dB for the first post tap
under the following conditions: low-frequency data pattern (five 1s and five 0s) at
6.375 Gbps. The levels listed in Table 1–38 are a representation of possible
pre-emphasis levels under these specified conditions only, the pre-emphasis levels
may change with data pattern and data rate.
To predict the pre-emphasis level for your specific data rate and pattern, run
simulations using the Arria II GX HSSI HSPICE models.
Table 1–38. Transmitter Pre-Emphasis Levels for Arria II GX Devices
Arria II GX
(Quartus II
Software)
First Post Tap
Setting
Arria II GX (Quartus II Software) VOD Setting
1
2
4
5
6
7
Unit
0 (off)
0
0
0
0
0
0
—
1
0.7
0
0
0
0
0
dB
2
2.7
1.2
0.3
0
0
0
dB
3
4.9
2.4
1.2
0.8
0.5
0.2
dB
4
7.5
3.8
2.1
1.6
1.2
0.6
dB
5
—
5.3
3.1
2.4
1.8
1.1
dB
6
—
7
4.3
3.3
2.7
1.7
dB
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–36
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–39 lists typical transmitter pre-emphasis levels for Arria II GZ devices (in dB)
for the first post tap under the following conditions (low-frequency data pattern [five
1s and five 0s] at 6.25 Gbps). The levels listed in Table 1–39 are a representation of
possible pre-emphasis levels under the specified conditions only and that the preemphasis levels may change with data pattern and data rate.
f To predict the pre-emphasis level for your specific data rate and pattern, run
simulations using the Arria II HSSI HSPICE models.
Table 1–39. Transmitter Pre-Emphasis Levels for Arria II GZ Devices (Part 1 of 2)
PreEmphasis
1st
Post-Tap
Setting
VOD Setting
0
1
2
3
4
5
6
7
0
0
0
0
0
0
0
0
0
1
N/A
0.7
0
0
0
0
0
0
2
N/A
1
0.3
0
0
0
0
0
3
N/A
1.5
0.6
0
0
0
0
0
4
N/A
2
0.7
0.3
0
0
0
0
5
N/A
2.7
1.2
0.5
0.3
0
0
0
6
N/A
3.1
1.3
0.8
0.5
0.2
0
0
7
N/A
3.7
1.8
1.1
0.7
0.4
0.2
0
8
N/A
4.2
2.1
1.3
0.9
0.6
0.3
0
9
N/A
4.9
2.4
1.6
1.2
0.8
0.5
0.2
10
N/A
5.4
2.8
1.9
1.4
1
0.7
0.3
11
N/A
6
3.2
2.2
1.7
1.2
0.9
0.4
12
N/A
6.8
3.5
2.6
1.9
1.4
1.1
0.6
13
N/A
7.5
3.8
2.8
2.1
1.6
1.2
0.6
14
N/A
8.1
4.2
3.1
2.3
1.7
1.3
0.7
15
N/A
8.8
4.5
3.4
2.6
1.9
1.5
0.8
16
N/A
N/A
4.9
3.7
2.9
2.2
1.7
0.9
17
N/A
N/A
5.3
4
3.1
2.4
1.8
1.1
18
N/A
N/A
5.7
4.4
3.4
2.6
2
1.2
19
N/A
N/A
6.1
4.7
3.6
2.8
2.2
1.4
20
N/A
N/A
6.6
5.1
4
3.1
2.4
1.5
21
N/A
N/A
7
5.4
4.3
3.3
2.7
1.7
22
N/A
N/A
8
6.1
4.8
3.8
3
2
23
N/A
N/A
9
6.8
5.4
4.3
3.4
2.3
24
N/A
N/A
10
7.6
6
4.8
3.9
2.6
25
N/A
N/A
11.4
8.4
6.8
5.4
4.4
3
26
N/A
N/A
12.6
9.4
7.4
5.9
4.9
3.3
27
N/A
N/A
N/A
10.3
8.1
6.4
5.3
3.6
28
N/A
N/A
N/A
11.3
8.8
7.1
5.8
4
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–37
Table 1–39. Transmitter Pre-Emphasis Levels for Arria II GZ Devices (Part 2 of 2)
PreEmphasis
1st
Post-Tap
Setting
VOD Setting
0
1
2
3
4
5
6
7
29
N/A
N/A
N/A
12.5
9.6
7.7
6.3
4.3
30
N/A
N/A
N/A
N/A
11.4
9
7.4
N/A
31
N/A
N/A
N/A
N/A
12.9
10
8.2
N/A
Table 1–40 lists the transceiver jitter specifications for all supported protocols for
Arria II GX devices.
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 1 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
SONET/SDH Transmit Jitter Generation (2)
Peak-to-peak
jitter at
622.08 Mbps
Pattern =
PRBS15
—
—
0.1
—
—
0.1
—
—
0.1
—
—
0.1
UI
RMS jitter at
622.08 Mbps
Pattern =
PRBS15
—
—
0.01
—
—
0.01
—
—
0.01
—
—
0.01
UI
Peak-to-peak
jitter at
2488.32 Mbps
Pattern =
PRBS15
—
—
0.1
—
—
0.1
—
—
0.1
—
—
0.1
UI
RMS jitter at
2488.32 Mbps
Pattern =
PRBS15
—
—
0.01
—
—
0.01
—
—
0.01
—
—
0.01
UI
SONET/SDH Receiver Jitter Tolerance (2)
Jitter frequency =
0.03 KHz
> 15
> 15
> 15
> 15
UI
> 1.5
> 1.5
> 1.5
> 1.5
UI
> 0.15
> 0.15
> 0.15
> 0.15
UI
Pattern = PRBS15
Jitter tolerance at
622.08 Mbps
Jitter frequency =
25 KHZ
Pattern = PRBS15
Jitter frequency =
250 KHz
Pattern = PRBS15
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–38
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 2 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Jitter frequency =
0.06 KHz
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
> 15
> 15
> 15
> 15
UI
> 1.5
> 1.5
> 1.5
> 1.5
UI
> 0.15
> 0.15
> 0.15
> 0.15
UI
> 0.15
> 0.15
> 0.15
> 0.15
UI
Pattern = PRBS15
Jitter frequency =
100 KHZ
Jitter tolerance at
2488.32 Mbps
Pattern = PRBS15
Jitter frequency =
1 MHz
Pattern = PRBS15
Jitter frequency =
10 MHz
Pattern = PRBS15
XAUI Transmit Jitter Generation (3)
Total jitter at
3.125 Gbps
Pattern = CJPAT
—
—
0.3
—
—
0.3
—
—
0.3
—
—
0.3
UI
Deterministic
jitter at
3.125 Gbps
Pattern = CJPAT
—
—
0.17
—
—
0.17
—
—
0.17
—
—
0.17
UI
XAUI Receiver Jitter Tolerance (3)
Total jitter
—
> 0.65
> 0.65
> 0.65
> 0.65
UI
Deterministic
jitter
—
> 0.37
> 0.37
> 0.37
> 0.37
UI
Peak-to-peak
jitter
Jitter frequency =
22.1 KHz
> 8.5
> 8.5
> 8.5
> 8.5
UI
Peak-to-peak
jitter
Jitter frequency =
1.875 MHz
> 0.1
> 0.1
> 0.1
> 0.1
UI
Peak-to-peak
jitter
Jitter frequency =
20 MHz
> 0.1
> 0.1
> 0.1
> 0.1
UI
PCIe Transmit Jitter Generation (4)
Total jitter at
2.5 Gbps (Gen1)
Compliance
pattern
—
—
0.25
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
—
—
0.25
—
—
0.25
—
—
0.25
July 2012 Altera Corporation
UI
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–39
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 3 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
PCIe Receiver Jitter Tolerance (4)
Total jitter at
2.5 Gbps (Gen1)
Compliance
pattern
> 0.6
> 0.6
> 0.6
> 0.6
UI
PCIe (Gen 1) Electrical Idle Detect Threshold (9)
VRX-IDLEDETDIFF (p-p)
Compliance
pattern
65
—
175
65
—
175
65
—
175
65
—
175
mV
Serial RapidIO® (SRIO) Transmit Jitter Generation (5)
Deterministic
jitter
Data Rate = 1.25,
2.5, 3.125 Gbps
(peak-to-peak)
Pattern = CJPAT
Total jitter
Data Rate = 1.25,
2.5, 3.125 Gbps
(peak-to-peak)
—
—
0.17
—
—
0.17
—
—
0.17
—
—
0.17
UI
—
—
0.35
—
—
0.35
—
—
0.35
—
—
0.35
UI
Pattern = CJPAT
SRIO Receiver Jitter Tolerance (5)
Deterministic
jitter tolerance
(peak-to-peak)
Combined
deterministic and
random jitter
tolerance
(peak-to-peak)
Data Rate = 1.25,
2.5, 3.125 Gbps
> 0.37
> 0.37
> 0.37
> 0.37
UI
> 0.55
> 0.55
> 0.55
> 0.55
UI
> 8.5
> 8.5
> 8.5
> 8.5
UI
> 0.1
> 0.1
> 0.1
> 0.1
UI
> 0.1
> 0.1
> 0.1
> 0.1
UI
Pattern = CJPAT
Data Rate = 1.25,
2.5, 3.125 Gbps
Pattern = CJPAT
Jitter frequency =
22.1 KHz
Data rate = 1.25,
2.5, 3.125 Gbps
Pattern = CJPAT
Sinusoidal jitter
tolerance
(peak-to-peak)
Jitter frequency =
1.875 MHz
Data rate = 1.25,
2.5, 3.125 Gbps
Pattern = CJPAT
Jitter frequency =
20 MHz
Data rate = 1.25,
2.5, 3.125 Gbps
Pattern = CJPAT
GIGE Transmit Jitter Generation (6)
Deterministic
jitter
Pattern = CRPAT
—
—
0.14
—
—
0.14
—
—
0.14
—
—
0.14
(peak-to-peak)
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
UI
1–40
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 4 of 10)
Symbol/
Description
Total jitter
(peak-to-peak)
I3
C4
C5, I5
C6
Conditions
Pattern = CRPAT
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
—
—
0.27
9
—
—
0.279
—
—
0.279
—
—
0.279
UI
GIGE Receiver Jitter Tolerance (6)
Deterministic
jitter tolerance
(peak-to-peak)
Pattern = CJPAT
> 0.4
> 0.4
> 0.4
> 0.4
UI
Combined
deterministic and
random jitter
tolerance
(peak-to-peak)
Pattern = CJPAT
> 0.66
> 0.66
> 0.66
> 0.66
UI
HiGig Transmit Jitter Generation (7)
Deterministic
jitter
(peak-to-peak)
Total jitter
(peak-to-peak)
Data rate =
3.75 Gbps
—
—
0.17
—
—
0.17
—
—
—
—
—
—
UI
—
—
0.35
—
—
0.35
—
—
—
—
—
—
UI
Pattern = CJPAT
Data rate =
3.75 Gbps
Pattern = CJPAT
HiGig Receiver Jitter Tolerance (7)
Deterministic
jitter tolerance
(peak-to-peak)
Combined
deterministic and
random jitter
tolerance
(peak-to-peak)
Data rate =
3.75 Gbps
> 0.37
> 0.37
—
—
—
—
—
—
UI
> 0.65
> 0.65
—
—
—
—
—
—
UI
> 8.5
> 8.5
—
—
—
—
—
—
UI
> 0.1
> 0.1
—
—
—
—
—
—
UI
> 0.1
> 0.1
—
—
—
—
—
—
UI
Pattern = CJPAT
Data rate =
3.75 Gbps
Pattern = CJPAT
Jitter frequency =
22.1 KHz
Data rate =
3.75 Gbps
Pattern = CJPAT
Sinusoidal jitter
tolerance
(peak-to-peak)
Jitter frequency =
1.875MHz
Data rate =
3.75 Gbps
Pattern = CJPAT
Jitter frequency =
20 MHz
Data rate =
3.75 Gbps
Pattern = CJPAT
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–41
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 5 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Data rate =
1.485 Gbps (HD)
pattern = Color
Bar Lowfrequency Roll-off
= 100 KHz
0.2
—
—
0.2
—
—
0.2
—
—
0.2
—
—
UI
Data rate =
2.97 Gbps (3G)
pattern = Color
bar Lowfrequency Roll-off
= 100 KHz
0.3
—
—
0.3
—
—
0.3
—
—
0.3
—
—
UI
SDI Transmitter Jitter Generation (8)
Alignment jitter
(peak-to-peak)
SDI Receiver Jitter Tolerance (8)
Jitter frequency =
15 KHz
Data rate =
2.97 Gbps (3G)
Pattern = single
line scramble
color bar
>2
>2
>2
>2
UI
> 0.3
> 0.3
> 0.3
> 0.3
UI
> 0.3
> 0.3
> 0.3
> 0.3
UI
Jitter frequency =
100 KHz
Sinusoidal jitter
tolerance
(peak-to-peak)
Data rate =
2.97 Gbps (3G)
Pattern = single
line scramble
color bar
Jitter frequency =
148.5 MHz
Data rate =
2.97 Gbps (3G)
Pattern = single
line scramble
color bar
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–42
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 6 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Jitter frequency =
20 KHz
Data rate =
1.485 Gbps (HD)
Pattern = 75%
color bar
Sinusoidal jitter
tolerance
(peak-to-peak)
Jitter frequency =
100 KHz
Data rate = 1.485
Gbps (HD)
Pattern = 75%
color bar
>1
>1
>1
>1
UI
> 0.2
> 0.2
> 0.2
> 0.2
UI
> 0.2
> 0.2
> 0.2
> 0.2
UI
Jitter frequency =
148.5 MHz
Data rate =
1.485 Gbps (HD)
Pattern =75%
color bar
SATA Transmit Jitter Generation (10)
Total jitter at
1.5 Gbps (G1)
Compliance
pattern
—
—
0.55
—
—
0.55
—
—
0.55
—
—
0.55
UI
Deterministic
jitter at 1.5 Gbps
(G1)
Compliance
pattern
—
—
0.35
—
—
0.35
—
—
0.35
—
—
0.35
UI
Total jitter at
3.0 Gbps (G2)
Compliance
pattern
—
—
0.55
—
—
0.55
—
—
0.55
—
—
0.55
UI
Deterministic
jitter at 3.0 Gbps
(G2)
Compliance
pattern
—
—
0.35
—
—
0.35
—
—
0.35
—
—
0.35
UI
Total jitter at
6.0 Gbps (G3)
Compliance
pattern
—
—
0.52
—
—
—
—
—
—
—
—
—
UI
Random jitter at
6.0 Gbps (G3)
Compliance
pattern
—
—
0.18
—
—
—
—
—
—
—
—
—
UI
SATA Receiver Jitter Tolerance (10)
Total jitter
tolerance at
1.5 Gbps (G1)
Compliance
pattern
> 0.65
> 0.65
> 0.65
> 0.65
UI
Deterministic
jitter tolerance at
1.5 Gbps (G1)
Compliance
pattern
> 0.35
> 0.35
> 0.35
> 0.35
UI
SSC modulation
frequency at
1.5 Gbps (G1)
Compliance
pattern
33
33
33
33
kHz
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–43
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 7 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
SSC modulation
deviation at
1.5 Gbps (G1)
Compliance
pattern
5700
5700
5700
5700
ppm
RX differential
skew at 1.5 Gbps
(G1)
Compliance
pattern
80
80
80
80
ps
RX AC common
mode voltage at
1.5 Gbps (G1)
Compliance
pattern
150
150
150
150
mV
Total jitter
tolerance at
3.0 Gbps (G2)
Compliance
pattern
> 0.65
> 0.65
> 0.65
> 0.65
UI
Deterministic
jitter tolerance at
3.0 Gbps (G2)
Compliance
pattern
> 0.35
> 0.35
> 0.35
> 0.35
UI
SSC modulation
frequency at
3.0 Gbps (G2)
Compliance
pattern
33
33
33
33
kHz
SSC modulation
deviation at
3.0 Gbps (G2)
Compliance
pattern
5700
5700
5700
5700
ppm
RX differential
skew at 3.0 Gbps
(G2)
Compliance
pattern
75
75
75
75
ps
RX AC common
mode voltage at
3.0 Gbps (G2)
Compliance
pattern
150
150
150
150
mV
Total jitter
tolerance at
6.0 Gbps (G3)
Compliance
pattern
> 0.60
> 0.60
> 0.60
> 0.60
UI
Random jitter
tolerance at
6.0 Gbps (G3)
Compliance
pattern
> 0.18
> 0.18
> 0.18
> 0.18
UI
SSC modulation
frequency at
6.0 Gbps (G3)
Compliance
pattern
33
33
33
33
kHz
SSC modulation
deviation at
6.0 Gbps (G3)
Compliance
pattern
5700
5700
5700
5700
ppm
RX differential
skew at 6.0 Gbps
(G3)
Compliance
pattern
30
30
30
30
ps
RX AC common
mode voltage at
6.0 Gbps (G3)
Compliance
pattern
100
100
100
100
mV
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–44
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 8 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
—
—
0.27
9
—
—
0.279
—
—
0.279
—
—
0.279
UI
—
—
0.35
—
—
0.35
—
—
0.35
—
—
0.35
UI
—
—
0.14
—
—
0.14
—
—
0.14
—
—
0.14
UI
—
—
0.17
—
—
0.17
—
—
0.17
—
—
0.17
UI
CPRI Transmit Jitter Generation (11)
E.6.HV, E.12.HV
Pattern = CJPAT
Total jitter
E.6.LV, E.12.LV,
E.24.LV, E.30.LV
Pattern = CJTPAT
E.6.HV, E.12.HV
Deterministic
jitter
Pattern = CJPAT
E.6.LV, E.12.LV,
E.24.LV, E.30.LV
Pattern = CJTPAT
CPRI Receiver Jitter Tolerance (11)
Total jitter
tolerance
Deterministic
jitter tolerance
E.6.HV, E.12.HV
Pattern = CJPAT
E.6.HV, E.12.HV
Pattern = CJPAT
E.6.LV, E.12.LV,
E.24.LV, E.30.LV
Total jitter
tolerance
E.60.LV
E.6.LV, E.12.LV,
E.24.LV, E.30.LV
> 0.66
> 0.66
UI
> 0.4
> 0.4
> 0.4
> 0.4
UI
> 0.65
> 0.65
> 0.65
> 0.65
UI
> 0.6
—
—
—
UI
> 0.37
> 0.37
> 0.37
> 0.37
UI
> 0.45
—
—
—
UI
> 0.55
> 0.55
> 0.55
> 0.55
UI
Pattern = CJTPAT
E.60.LV
Pattern = PRBS31
Combined
deterministic and
random jitter
tolerance
> 0.66
Pattern = CJTPAT
Pattern = PRBS31
Deterministic
jitter tolerance
> 0.66
E.6.LV, E.12.LV,
E.24.LV, E.30.LV
Pattern = CJTPAT
OBSAI Transmit Jitter Generation (12)
Total jitter at
768 Mbps,
1536 Mbps, and
3072 Mbps
Deterministic
jitter at
768 Mbps,
1536 Mbps, and
3072 Mbps
REFCLK =
153.6 MHz
—
—
0.35
—
—
0.35
—
—
0.35
—
—
0.35
UI
—
—
0.17
—
—
0.17
—
—
0.17
—
—
0.17
UI
Pattern = CJPAT
REFCLK =
153.6 MHz
Pattern = CJPAT
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–45
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 9 of 10)
Symbol/
Description
I3
C4
C5, I5
C6
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
OBSAI Receiver Jitter Tolerance (12)
Deterministic
jitter tolerance at
768 Mbps,
1536 Mbps, and
3072 Mbps
Pattern = CJPAT
> 0.37
> 0.37
> 0.37
> 0.37
UI
Combined
deterministic and
random jitter
tolerance at
768 Mbps,
1536 Mbps, and
3072 Mbps
Pattern = CJPAT
> 0.55
> 0.55
> 0.55
> 0.55
UI
Jitter frequency =
5.4 KHz
> 8.5
> 8.5
> 8.5
> 8.5
UI
> 0.1
> 0.1
> 0.1
> 0.1
UI
> 8.5
> 8.5
> 8.5
> 8.5
UI
> 0.1
> 0.1
> 0.1
> 0.1
UI
Sinusoidal jitter
tolerance at
768 Mbps
Pattern = CJPAT
Jitter frequency =
460.8 KHz to 20
MHz
Pattern = CJPAT
Jitter frequency =
10.9 KHz
Sinusoidal jitter
tolerance at
1536 Mbps
Pattern = CJPAT
Jitter frequency =
921.6 KHz to 20
MHz
Pattern = CJPAT
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–46
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–40. Transceiver Block Jitter Specifications for Arria II GX Devices (Note 1) (Part 10 of 10)
I3
Symbol/
Description
C5, I5
C6
Unit
Min
Jitter frequency =
21.8 KHz
Sinusoidal jitter
tolerance at
3072 Mbps
C4
Conditions
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
> 8.5
> 8.5
> 8.5
> 8.5
UI
> 0.1
> 0.1
> 0.1
> 0.1
UI
Pattern = CJPAT
Jitter frequency =
1843.2 KHz to 20
MHz
Pattern = CJPAT
Notes to Table 1–40:
(1) Dedicated refclk pins are used to drive the input reference clocks. The jitter numbers are valid for the stated conditions only.
(2) The jitter numbers for SONET/SDH are compliant to the GR-253-CORE Issue 3 Specification.
(3) The jitter numbers for XAUI are compliant to the IEEE802.3ae-2002 Specification.
(4) The jitter numbers for PCIe are compliant to the PCIe Base Specification 2.0.
(5) The jitter numbers for SRIO are compliant to the RapidIO Specification 1.3.
(6) The jitter numbers for GIGE are compliant to the IEEE802.3-2002 Specification.
(7) The jitter numbers for HiGig are compliant to the IEEE802.3ae-2002 Specification.
(8) The HD-SDI and 3G-SDI jitter numbers are compliant to the SMPTE292M and SMPTE424M Specifications.
(9) Arria II PCIe receivers are compliant to this specification provided the VTX_CM-DC-ACTIVEIDLE-DELTA of the upstream transmitter is less than 50 mV.
(10) The jitter numbers for Serial Advanced Technology Attachment (SATA) are compliant to the Serial ATA Revision 3.0 Specification.
(11) The jitter numbers for Common Public Radio Interface (CPRI) are compliant to the CPRI Specification V3.0.
(12) The jitter numbers for Open Base Station Architecture Initiative (OBSAI) are compliant to the OBSAI RP3 Specification V4.1.
Table 1–41 lists the transceiver jitter specifications for all supported protocols for
Arria II GZ devices.
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 1 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
SONET/SDH Transmit Jitter Generation (3)
Peak-to-peak jitter at
622.08 Mbps
Pattern = PRBS15
—
—
0.1
—
—
0.1
UI
RMS jitter at 622.08 Mbps
Pattern = PRBS15
—
—
0.01
—
—
0.01
UI
Peak-to-peak jitter at 2488.32
Mbps
Pattern = PRBS15
—
—
0.1
—
—
0.1
UI
RMS jitter at 2488.32 Mbps
Pattern = PRBS15
—
—
0.01
—
—
0.01
UI
SONET/SDH Receiver Jitter Tolerance (3)
Jitter frequency = 0.03 KHz
Pattern = PRBS15
Jitter tolerance at 622.08 Mbps
Jitter frequency =
25 KHZ
> 15
> 15
UI
> 1.5
> 1.5
UI
> 0.15
> 0.15
UI
Pattern = PRBS15
Jitter frequency = 250 KHz
Pattern = PRBS15
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–47
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 2 of 7)
Symbol/
Description
–C3 and –I3
Unit
Min
Jitter frequency = 0.06 KHz
Pattern = PRBS15
Jitter frequency = 100 KHZ
Pattern = PRBS15
Jitter tolerance at 2488.32 Mbps
–C4 and –I4
Conditions
Jitter frequency =
1 MHz
Typ
Max
Min
Typ
Max
> 15
> 15
UI
> 1.5
> 1.5
UI
> 0.15
> 0.15
UI
> 0.15
> 0.15
UI
Pattern = PRBS15
Jitter frequency = 10 MHz
Pattern = PRBS15
Fibre Channel Transmit Jitter Generation (4), (5)
Total jitter FC-1
Pattern = CRPAT
—
—
0.23
—
—
0.23
UI
Deterministic jitter FC-1
Pattern = CRPAT
—
—
0.11
—
—
0.11
UI
Total jitter FC-2
Pattern = CRPAT
—
—
0.33
—
—
0.33
UI
Deterministic jitter FC-2
Pattern = CRPAT
—
—
0.2
—
—
0.2
UI
Total jitter FC-4
Pattern = CRPAT
—
—
0.52
—
—
0.52
UI
Deterministic jitter FC-4
Pattern = CRPAT
—
—
0.33
—
—
0.33
UI
Fibre Channel Receiver Jitter Tolerance (4), (6)
Deterministic jitter FC-1
Pattern = CJTPAT
> 0.37
> 0.37
UI
Random jitter
FC-1
Pattern = CJTPAT
> 0.31
> 0.31
UI
Fc/25000
> 1.5
> 1.5
UI
Fc/1667
> 0.1
> 0.1
UI
Deterministic jitter FC-2
Pattern = CJTPAT
> 0.33
> 0.33
UI
Random jitter
FC-2
Pattern = CJTPAT
> 0.29
> 0.29
UI
Fc/25000
> 1.5
> 1.5
UI
Fc/1667
> 0.1
> 0.1
UI
Deterministic jitter FC-4
Pattern = CJTPAT
> 0.33
> 0.33
UI
Random jitter FC-4
Pattern = CJTPAT
> 0.29
> 0.29
UI
Fc/25000
> 1.5
> 1.5
UI
Fc/1667
> 0.1
> 0.1
UI
Sinusoidal jitter FC-1
Sinusoidal jitter FC-2
Sinusoidal jitter FC-4
XAUI Transmit Jitter Generation (7)
Total jitter at 3.125 Gbps
Pattern = CJPAT
—
—
0.3
—
—
0.3
UI
Deterministic jitter at
3.125 Gbps
Pattern = CJPAT
—
—
0.17
—
—
0.17
UI
XAUI Receiver Jitter Tolerance (7)
Total jitter
—
> 0.65
> 0.65
UI
Deterministic jitter
—
> 0.37
> 0.37
UI
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–48
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 3 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Peak-to-peak jitter
Jitter frequency = 22.1 KHz
> 8.5
> 8.5
UI
Peak-to-peak jitter
Jitter frequency =
1.875 MHz
> 0.1
> 0.1
UI
Peak-to-peak jitter
Jitter frequency = 20 MHz
> 0.1
> 0.1
UI
PCIe Transmit Jitter Generation (8)
Total jitter at 2.5 Gbps (Gen1)—
x1, x4, and x8
Compliance pattern
—
—
0.25
—
—
0.25
UI
Total jitter at 5 Gbps (Gen2)—
x1, x4, and x8
Compliance pattern
—
—
0.25
—
—
—
UI
PCIe Receiver Jitter Tolerance (8)
Total jitter at 2.5 Gbps (Gen1)
Compliance pattern
> 0.6
> 0.6
UI
Total jitter at 5 Gbps (Gen2)
Compliance pattern
Not supported
Not supported
UI
PCIe (Gen 1) Electrical Idle Detect Threshold
VRX-IDLE-DETDIFFp-p (9)
Compliance pattern
65
—
175
65
—
175
UI
—
—
0.17
—
—
0.17
UI
—
—
0.35
—
—
0.35
UI
SRIO Transmit Jitter Generation (10)
Deterministic jitter
Data rate = 1.25, 2.5, 3.125 Gbps
(peak-to-peak)
Total jitter (peak-to-peak)
Pattern = CJPAT
Data rate = 1.25, 2.5, 3.125 Gbps
Pattern = CJPAT
SRIO Receiver Jitter Tolerance (10)
Deterministic jitter tolerance
(peak-to-peak)
Data rate = 1.25, 2.5, 3.125 Gbps
Combined deterministic and
random jitter tolerance (peak-topeak)
Data rate = 1.25, 2.5, 3.125 Gbps
Pattern = CJPAT
Pattern = CJPAT
> 0.37
> 0.37
UI
> 0.55
> 0.55
UI
> 8.5
> 8.5
UI
> 0.1
> 0.1
UI
> 0.1
> 0.1
UI
Jitter frequency = 22.1 KHz
Data rate = 1.25, 2.5, 3.125 Gbps
Pattern = CJPAT
Jitter frequency = 1.875 MHz
Sinusoidal jitter tolerance (peakto-peak)
Data rate = 1.25, 2.5, 3.125 Gbps
Pattern = CJPAT
Jitter frequency = 20 MHz
Data rate = 1.25, 2.5, 3.125 Gbps
Pattern = CJPAT
GIGE Transmit Jitter Generation (11)
Deterministic jitter
(peak-to-peak)
Pattern = CRPAT
—
—
0.14
—
—
0.14
UI
Total jitter (peak-to-peak)
Pattern = CRPAT
—
—
0.279
—
—
0.279
UI
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–49
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 4 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
GIGE Receiver Jitter Tolerance (11)
Deterministic jitter tolerance
(peak-to-peak)
Pattern = CJPAT
> 0.4
> 0.4
UI
Combined deterministic and
random jitter tolerance (peak-topeak)
Pattern = CJPAT
> 0.66
> 0.66
UI
HiGig Transmit Jitter Generation
Data rate = 3.75 Gbps
Deterministic jitter
(peak-to-peak)
Pattern = CJPAT
Data rate = 3.75 Gbps
Total jitter (peak-to-peak)
Pattern = CJPAT
—
—
0.17
—
—
—
UI
—
—
0.35
—
—
—
UI
> 0.37
—
—
—
UI
> 0.65
—
—
—
UI
> 8.5
—
—
—
UI
> 0.1
—
—
—
UI
> 0.1
—
—
—
UI
—
—
0.3
UI
> 0.675
—
—
—
UI
> 0.988
—
—
—
UI
HiGig Receiver Jitter Tolerance
Deterministic jitter tolerance
(peak-to-peak)
Data rate = 3.75 Gbps
Combined deterministic and
random jitter tolerance (peak-topeak)
Data rate = 3.75 Gbps
Pattern = CJPAT
Pattern = CJPAT
Jitter frequency = 22.1 KHz
Data rate = 3.75 Gbps
Pattern = CJPAT
Jitter frequency = 22.1 KHz
Sinusoidal jitter tolerance (peakto-peak)
Data rate = 3.75 Gbps
Pattern = CJPAT
Jitter frequency = 22.1 KHz
Data rate = 3.75 Gbps
Pattern = CJPAT
(OIF) CEI Transmitter Jitter Generation
Total jitter (peak-to-peak)
Data rate = 6.375 Gbps
Pattern = PRBS15 BER = 10-12
—
—
0.3
(OIF) CEI Receiver Jitter Tolerance
Deterministic jitter tolerance
(peak-to-peak)
Combined deterministic and
random jitter tolerance (peak-topeak)
July 2012
Altera Corporation
Data rate = 6.375 Gbps
Pattern = PRBS31 BER = 10-12
Data rate = 6.375 Gbps
Pattern = PRBS31 BER = 10-12
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–50
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 5 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
> 0.5
—
—
—
UI
> 0.05
—
—
—
UI
> 0.05
—
—
—
UI
Jitter Frequency = 38.2 KHz
Data rate = 6.375 Gbps
Pattern = PRBS31 BER = 10-12
Jitter Frequency = 3.82 MHz
Sinusoidal jitter tolerance (peakto-peak)
Data rate = 6.375 Gbps
Pattern = PRBS31 BER =
10-12
Jitter Frequency = 20 MHz
Data rate = 6.375 Gbps
Pattern = PRBS31 BER =
10-12
SDI Transmitter Jitter Generation (12)
Alignment jitter
(peak-to-peak)
Data rate = 1.485 Gbps (HD)
Pattern = color bar Low-frequency
roll-off = 100 KHz
0.2
—
—
0.2
—
—
UI
Data rate = 2.97 Gbps (3G) Pattern
= color bar Low-frequency roll-off
= 100 KHz
0.3
—
—
0.3
—
—
UI
SDI Receiver Jitter Tolerance (12)
Jitter frequency = 15 KHz
Data rate = 2.97 Gbps (3G) Pattern
= single line scramble color bar
Sinusoidal jitter tolerance (peakto-peak)
>2
>2
UI
> 0.3
> 0.3
UI
> 0.3
> 0.3
UI
>1
>1
UI
> 0.2
> 0.2
UI
> 0.2
> 0.2
UI
Jitter frequency = 100 KHz
Data rate = 2.97 Gbps (3G) Pattern
= single line scramble color bar
Jitter frequency = 148.5 MHz
Data rate = 2.97 Gbps (3G) Pattern
= single line scramble color bar
Jitter frequency = 20 KHz
Data rate = 1.485 Gbps (HD)
pattern = 75% color bar
Sinusoidal jitter tolerance (peakto-peak)
Jitter frequency = 100 KHz
Data rate = 1.485 Gbps (HD)
Pattern = 75% color bar
Jitter frequency = 148.5 MHz
Data rate = 1.485 Gbps (HD)
Pattern = 75% color bar
SAS Transmit Jitter Generation (13)
Total jitter at 1.5 Gbps (G1)
Pattern = CJPAT
—
—
0.55
—
—
0.55
UI
Deterministic jitter at 1.5 Gbps
(G1)
Pattern = CJPAT
—
—
0.35
—
—
0.35
UI
Total jitter at 3.0 Gbps (G2)
Pattern = CJPAT
—
—
0.55
—
—
0.55
UI
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–51
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 6 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Deterministic jitter at 3.0 Gbps
(G2)
Pattern = CJPAT
—
—
0.35
—
—
0.35
UI
Total jitter at 6.0 Gbps (G3)
Pattern = CJPAT
—
—
0.25
—
—
0.25
UI
Random jitter at 6.0 Gbps (G3)
Pattern = CJPAT
—
—
0.15
—
—
0.15
UI
Total jitter tolerance at 1.5 Gbps
(G1)
Pattern = CJPAT
—
—
0.65
—
—
0.65
UI
Deterministic jitter tolerance at
1.5 Gbps (G1)
Pattern = CJPAT
—
—
0.35
—
—
0.35
UI
SAS Receiver Jitter Tolerance (13)
Sinusoidal jitter tolerance at 1.5
Gbps (G1)
Jitter frequency = 900 KHz to 5
MHz
> 0.1
> 0.1
UI
Pattern = CJTPAT BER = 1E-12
CPRI Transmit Jitter Generation (14)
E.6.HV, E.12.HV
Total jitter
Pattern = CJPAT
E.6.LV, E.12.LV, E.24.LV, E.30.LV
Pattern = CJPAT
E.6.HV, E.12.HV
Deterministic jitter
Pattern = CJPAT
E.6.LV, E.12.LV, E.24.LV, E.30.LV
Pattern = CJPAT
—
—
0.279
—
—
0.279
UI
—
—
0.35
—
—
0.35
UI
—
—
0.14
—
—
0.14
UI
—
—
0.17
—
—
0.17
UI
CPRI Receiver Jitter Tolerance (14)
E.6.HV, E.12.HV
Total jitter tolerance
Pattern = CJPAT
E.6.HV, E.12.HV
Deterministic jitter tolerance
Total jitter tolerance
Deterministic jitter tolerance
Combined deterministic and
random jitter tolerance
Pattern = CJPAT
E.6.LV, E.12.LV, E.24.LV, E.30.LV
Pattern = CJPAT
E.6.LV, E.12.LV, E.24.LV, E.30.LV
Pattern = CJPAT
E.6.LV, E.12.LV, E.24.LV, E.30.LV
Pattern = CJPAT
> 0.66
> 0.66
UI
> 0.4
> 0.4
UI
> 0.65
> 0.65
UI
> 0.37
> 0.37
UI
> 0.55
> 0.55
UI
OBSAI Transmit Jitter Generation (15)
Total jitter at 768 Mbps, 1536
Mbps, and 3072 Mbps
REFCLK = 153.6 MHz
Deterministic jitter at 768 MBps,
1536 Mbps, and 3072 Mbps
REFCLK = 153.6 MHz
July 2012
Altera Corporation
Pattern CJPAT
Pattern CJPAT
—
—
0.35
—
—
0.35
UI
—
—
0.17
—
—
0.17
UI
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–52
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–41. Transceiver Block Jitter Specifications for Arria II GZ Devices (Note 1), (2) (Part 7 of 7)
–C3 and –I3
Symbol/
Description
–C4 and –I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
OBSAI Receiver Jitter Tolerance (15)
Deterministic jitter tolerance at
768 Mbps, 1536 Mbps, and
3072 Mbps
Pattern = CJPAT
> 0.37
> 0.37
UI
Combined deterministic and
random jitter tolerance at 768
Mbps, 1536 Mbps, and 3072
Mbps
Pattern = CJPAT
> 0.55
> 0.55
UI
> 8.5
> 8.5
UI
> 0.1
> 0.1
UI
> 8.5
> 8.5
UI
> 0.1
> 0.1
UI
> 8.5
> 8.5
UI
> 0.1
> 0.1
UI
Jitter frequency = 5.4 KHz
Sinusoidal jitter tolerance at 768
Mbps
Pattern = CJPAT
Jitter frequency = 460 MHz to 20
MHz
Pattern = CJPAT
Jitter frequency = 10.9 KHz
Sinusoidal jitter tolerance at
1536 Mbps
Pattern = CJPAT
Jitter frequency = 921.6 MHz to 20
MHz
Pattern = CJPAT
Jitter frequency = 21.8 KHz
Sinusoidal jitter tolerance at
3072 Mbps
Pattern = CJPAT
Jitter frequency = 1843.2 MHz to
20 MHz
Pattern = CJPAT
Notes to Table 1–41:
(1) Dedicated refclk pins were used to drive the input reference clocks.
(2) The jitter numbers are valid for the stated conditions only.
(3) The jitter numbers for SONET/SDH are compliant to the GR-253-CORE Issue 3 Specification.
(4) The jitter numbers for Fibre Channel are compliant to the FC-PI-4 Specification revision 6.10.
(5) The Fibre Channel transmitter jitter generation numbers are compliant to the specification at the T inter operability point.
(6) The Fibre Channel receiver jitter tolerance numbers are compliant to the specification at the R interpretability point.
(7) The jitter numbers for XAUI are compliant to the IEEE802.3ae-2002 Specification.
(8) The jitter numbers for PCIe are compliant to the PCIe Base Specification 2.0.
(9) Arria II GZ PCIe receivers are compliant to this specification provided the VTX-CM-DC-ACTIVEIDLE-DELTA of the upstream transmitter is less than 50 mV.
(10) The jitter numbers for SRIO are compliant to the RapidIO Specification 1.3.
(11) The jitter numbers for GIGE are compliant to the IEEE802.3-2002 Specification.
(12) The HD-SDI and 3G-SDI jitter numbers are compliant to the SMPTE292M and SMPTE424M Specifications.
(13) The jitter numbers for Serial Attached SCSI (SAS) are compliant to the SAS-2.1 Specification.
(14) The jitter numbers for CPRI are compliant to the CPRI Specification V3.0.
(15) The jitter numbers for OBSAI are compliant to the OBSAI RP3 Specification V4.1.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–53
Core Performance Specifications for the Arria II Device Family
This section describes the clock tree, phase-locked loop (PLL), digital signal
processing (DSP), embedded memory, configuration, and JTAG specifications for
Arria II GX and GZ devices.
Clock Tree Specifications
Table 1–42 lists the clock tree specifications for Arria II GX devices.
Table 1–42. Clock Tree Performance for Arria II GX Devices
Performance
Clock Network
Unit
I3, C4
C5,I5
C6
GCLK and RCLK
500
500
400
MHz
PCLK
420
350
280
MHz
Table 1–43 lists the clock tree specifications for Arria II GZ devices.
Table 1–43. Clock Tree Performance for Arria II GZ Devices
Performance
Clock Network
Unit
–C3 and –I3
–C4 and –I4
GCLK and RCLK
700
500
MHz
PCLK
500
450
MHz
PLL Specifications
Table 1–44 lists the PLL specifications for Arria II GX devices.
Table 1–44. PLL Specifications for Arria II GX Devices (Part 1 of 3)
Symbol
Min
Typ
Max
Unit
Input clock frequency (from clock input pins residing in
right/top/bottom banks) (–4 Speed Grade)
5
—
670 (1)
MHz
Input clock frequency (from clock input pins residing in
right/top/bottom banks) (–5 Speed Grade)
5
—
622 (1)
MHz
Input clock frequency (from clock input pins residing in
right/top/bottom banks) (–6 Speed Grade)
5
—
500 (1)
MHz
fINPFD
Input frequency to the PFD
5
—
325
MHz
fVCO
PLL VCO operating Range (2)
600
—
1,400
MHz
fINDUTY
Input clock duty cycle
40
—
60
%
fEINDUTY
External feedback clock input duty cycle
40
—
60
%
tINCCJ (3),
(4)
Input clock cycle-to-cycle jitter (Frequency  100 MHz)
—
—
0.15
UI (p–p)
Input clock cycle-to-cycle jitter (Frequency  100 MHz)
—
—
±750
ps (p–p)
fIN
July 2012
Description
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–54
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–44. PLL Specifications for Arria II GX Devices (Part 2 of 3)
Symbol
fOUT
fOUT_EXT
tOUTDUTY
Description
Min
Typ
Max
Unit
Output frequency for internal global or regional clock
(–4 Speed Grade)
—
—
500
MHz
Output frequency for internal global or regional clock
(–5 Speed Grade)
—
—
500
MHz
Output frequency for internal global or regional clock
(–6 Speed Grade)
—
—
400
MHz
Output frequency for external clock output (–4 Speed Grade)
—
—
670 (5)
MHz
Output frequency for external clock output (–5 Speed Grade)
—
—
622 (5)
MHz
Output frequency for external clock output (–6 Speed Grade)
—
—
500 (5)
MHz
Duty cycle for external clock output (when set to 50%)
45
50
55
%
Dedicated clock output period jitter (fOUT  100 MHz)
—
—
300
ps (p–p)
Dedicated clock output period jitter (fOUT  100 MHz)
—
—
30
mUI (p–p)
Dedicated clock output cycle-to-cycle jitter (fOUT  100 MHz)
—
—
300
ps (p–p)
Dedicated clock output cycle-to-cycle jitter (fOUT  100 MHz)
—
—
30
mUI (p–p)
Regular I/O clock output period jitter (fOUT  100 MHz)
—
—
650
ps (p–p)
Regular I/O clock output period jitter (fOUT  100 MHz)
—
—
65
mUI (p–p)
Regular I/O clock output cycle-to-cycle jitter (fOUT  100 MHz)
—
—
650
ps (p–p)
Regular I/O clock output cycle-to-cycle jitter (fOUT  100 MHz)
—
—
65
mUI (p–p)
tCONFIGPLL
Time required to reconfigure PLL scan chains
—
3.5
—
SCANCLK
cycles
tCONFIGPHASE
Time required to reconfigure phase shift
—
1
—
SCANCLK
cycles
fSCANCLK
SCANCLK frequency
—
—
100
MHz
tLOCK
Time required to lock from end of device configuration
—
—
1
ms
tDLOCK
Time required to lock dynamically (after switchover or
reconfiguring any non-post-scale counters/delays)
—
—
1
ms
PLL closed-loop low bandwidth
—
0.3
—
MHz
PLL closed-loop medium bandwidth
—
1.5
—
MHz
PLL closed-loop high bandwidth
—
4
—
MHz
tPLL_PSERR
Accuracy of PLL phase shift
—
—
±50
ps
tARESET
Minimum pulse width on areset signal
10
—
—
ns
tOUTPJ_DC
tOUTCCJ_DC
fOUTPJ_IO
fOUTCCJ_IO
fCL B W
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–55
Table 1–44. PLL Specifications for Arria II GX Devices (Part 3 of 3)
Symbol
tCASC_
OUTJITTER_
PERIOD_
DEDCLK
(6), (7)
Description
Min
Typ
Max
Unit
Period Jitter for dedicated clock output in cascaded PLLs
(FOUT  100 MHz)
—
—
425
ps (p-p)
Period Jitter for dedicated clock output in cascaded PLLs
(FOUT  100 MHz)
—
—
42.5
mUI (p-p)
Notes to Table 1–44:
(1) fIN is limited by the I/O fMAX.
(2) The VCO frequency reported by the Quartus II software in the PLL summary section of the compilation report takes into consideration the VCO
post-scale counter K value. Therefore, if the counter K has a value of 2, the frequency reported can be lower than the fVCO specification.
(3) A high-input jitter directly affects the PLL output jitter. To have low PLL output clock jitter, you must provide a clean-clock source, which is
less than 200 ps.
(4) FREF is fIN/N when N = 1.
(5) This specification is limited by the lower of the two: I/O fMAX or fOUT of the PLL.
(6) Peak-to-peak jitter with a probability level of 10–12 (14 sigma, 99.99999999974404% confidence level). The output jitter specification applies
to the intrinsic jitter of the PLL, when an input jitter of 30 ps is applied. The external memory interface clock output jitter specifications use a
different measurement method and are available in Table 1–62 on page 1–70.
(7) The cascaded PLL specification is only applicable with the following condition:
a. Upstream PLL: 0.59 Mhz Upstream PLL BW < 1 MHz
b. Downstream PLL: Downstream PLL BW > 2 MHz
Table 1–45 lists the PLL specifications for Arria II GZ devices when operating in both
the commercial junction temperature range (0° to 85°C) and the industrial junction
temperature range (-40° to 100°C).
Table 1–45. PLL Specifications for Arria II GZ Devices (Part 1 of 2)
Symbol
fIN
fINPFD
fVCO
tEINDUTY
fOUT
fOUT_EXT
Parameter
Min
Typ
Max
Unit
Input clock frequency (–3 speed grade)
5
—
717 (1)
MHz
Input clock frequency (–4 speed grade)
5
—
717 (1)
MHz
Input frequency to the PFD
5
—
325
MHz
PLL VCO operating range (–3 speed grade)
600
—
1,300
MHz
PLL VCO operating range (–4 speed grade)
600
—
1,300
MHz
Input clock or external feedback clock input duty cycle
40
—
60
%
Output frequency for internal global or regional clock
(–3 speed grade)
—
—
700 (2)
MHz
Output frequency for internal global or regional clock
(–4 speed grade)
—
—
500 (2)
MHz
Output frequency for external clock output (–3 speed grade)
—
—
717 (2)
MHz
Output frequency for external clock output (–4 speed grade)
—
—
717 (2)
MHz
tOUTDUTY
Duty cycle for external clock output (when set to 50%)
45
50
55
%
tFCOMP
External feedback clock compensation time
—
—
10
ns
tCONFIGPLL
Time required to reconfigure scan chain
—
3.5
—
scanclk
cycles
tCONFIGPHASE
Time required to reconfigure phase shift
—
1
—
scanclk
cycles
fSCANCLK
scanclk frequency
—
—
100
MHz
tLOCK
Time required to lock from end-of-device configuration or
de-assertion of areset
—
—
1
ms
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–56
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–45. PLL Specifications for Arria II GZ Devices (Part 2 of 2)
Symbol
Min
Typ
Max
Unit
Time required to lock dynamically (after switchover or
reconfiguring any non-post-scale counters/delays)
—
—
1
ms
PLL closed-loop low bandwidth
—
0.3
—
MHz
PLL closed-loop medium bandwidth
—
1.5
—
MHz
PLL closed-loop high bandwidth (7)
—
4
—
MHz
tPLL_PSERR
Accuracy of PLL phase shift
—
—
±50
ps
tARESET
Minimum pulse width on the areset signal
10
—
—
ns
Input clock cycle to cycle jitter (FREF ≥ 100 MHz)
—
—
0.15
UI (p-p)
Input clock cycle to cycle jitter (FREF < 100 MHz)
—
—
±750
ps (p-p)
Period Jitter for dedicated clock output (FOUT ≥ 100 MHz)
—
—
175
ps (p-p)
Period Jitter for dedicated clock output (FOUT < 100 MHz)
—
—
17.5
mUI (p-p)
Cycle to Cycle Jitter for dedicated clock output
(FOUT ≥ 100 MHz)
—
—
175
ps (p-p)
Cycle to Cycle Jitter for dedicated clock output
(FOUT < 100 MHz)
—
—
17.5
mUI (p-p)
Period Jitter for clock output on regular I/O
(FOUT ≥ 100 MHz)
—
—
600
ps (p-p)
Period Jitter for clock output on regular I/O
(FOUT < 100 MHz)
—
—
60
mUI (p-p)
Cycle to Cycle Jitter for clock output on regular I/O
(FOUT ≥ 100 MHz)
—
—
600
ps (p-p)
Cycle to Cycle Jitter for clock output on regular I/O
(FOUT < 100 MHz)
—
—
60
mUI (p-p)
Period Jitter for dedicated clock output in cascaded PLLs
(FOUT ≥100MHz)
—
—
250
ps (p-p)
Period Jitter for dedicated clock output in cascaded PLLs
(FOUT < 100MHz)
—
—
25
mUI (p-p)
Frequency drift after PFDENA is disabled for duration of
100 us
—
—
±10
%
tDLOCK
fCLBW
tINCCJ (3), (4)
tOUTPJ_DC (5)
tOUTCCJ_DC (5)
tOUTPJ_IO (5),
(8)
tOUTCCJ_IO (5),
(8)
tCASC_OUTPJ_DC
(5), (6)
fDRIFT
Parameter
Notes to Table 1–45:
(1) This specification is limited in the Quartus II software by the I/O maximum frequency. The maximum I/O frequency is different for each I/O
standard.
(2) This specification is limited by the lower of the two: I/O FMAX or FOUT of the PLL.
(3) A high input jitter directly affects the PLL output jitter. To have low PLL output clock jitter, you must provide a clean clock source that is less
than 120 ps.
(4) FREF is fIN/N when N = 1.
(5) Peak-to-peak jitter with a probability level of 10–12 (14 sigma, 99.99999999974404% confidence level). The output jitter specification applies
to the intrinsic jitter of the PLL, when an input jitter of 30 ps is applied. The external memory interface clock output jitter specifications use a
different measurement method and are available in Table 1–64 on page 1–71.
(6) The cascaded PLL specification is only applicable with the following condition:
a. Upstream PLL: 0.59 Mhz  Upstream PLL BW < 1 MHz
b. Downstream PLL: Downstream PLL BW > 2 MHz
(7) High bandwidth PLL settings are not supported in external feedback mode.
(8) External memory interface clock output jitter specifications use a different measurement method, which is available in Table 1–63 on
page 1–71.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–57
DSP Block Specifications
Table 1–46 lists the DSP block performance specifications for Arria II GX devices.
Table 1–46. DSP Block Performance Specifications for Arria II GX Devices (Note 1)
Resources
Used
Performance
Mode
Unit
Number of
Multipliers
C4
I3
C5,I5
C6
9 × 9-bit multiplier
1
380
310
300
250
MHz
12 × 12-bit multiplier
1
380
310
300
250
MHz
18 × 18-bit multiplier
1
380
310
300
250
MHz
36 × 36-bit multiplier
1
350
270
270
220
MHz
18 × 36-bit high-precision multiplier
adder mode
1
350
270
270
220
MHz
18 × 18-bit multiply accumulator
4
380
310
300
250
MHz
18 × 18-bit multiply adder
4
380
310
300
250
MHz
18 × 18-bit multiply adder-signed full
precision
2
380
310
300
250
MHz
18 × 18-bit multiply adder with
loopback (2)
2
275
220
220
180
MHz
36-bit shift (32-bit data)
1
350
270
270
220
MHz
Double mode
1
350
270
270
220
MHz
Notes to Table 1–46:
(1) Maximum is for a fully-pipelined block with Round and Saturation disabled.
(2) Maximum is for loopback input registers disabled, Round and Saturation disabled, pipeline and output registers enabled.
Table 1–47 lists the DSP block performance specifications for Arria II GZ devices.
Table 1–47. DSP Block Performance Specifications for Arria II GZ Devices (Note 1) (Part 1 of 2)
Resources
Used
Performance
Mode
Unit
Number of
Multipliers
–3
–4
9 × 9-bit multiplier
1
460
400
MHz
12 × 12-bit multiplier
1
500
440
MHz
18 × 18-bit multiplier
1
550
480
MHz
36 × 36-bit multiplier
1
440
380
MHz
18 × 18-bit multiply accumulator
4
440
380
MHz
18 × 18-bit multiply adder
4
470
410
MHz
18 × 18-bit multiply adder-signed full
precision
2
450
390
MHz
18 × 18-bit multiply adder with
loopback (2)
2
350
310
MHz
36-bit shift (32-bit data)
1
440
380
MHz
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–58
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–47. DSP Block Performance Specifications for Arria II GZ Devices (Note 1) (Part 2 of 2)
Resources
Used
Performance
Mode
Unit
Number of
Multipliers
–3
–4
1
440
380
Double mode
MHz
Notes to Table 1–47:
(1) Maximum is for fully pipelined block with Round and Saturation disabled.
(2) Maximum for loopback input registers disabled, Round and Saturation disabled, and pipeline and output registers enabled.
Embedded Memory Block Specifications
Table 1–48 lists the embedded memory block specifications for Arria II GX devices.
Table 1–48. Embedded Memory Block Performance Specifications for Arria II GX Devices
Resources Used
Memory
Memory
Logic
Array
Block
(MLAB)
M9K
Block
Mode
Performance
Unit
ALUTs
Embedded
Memory
I3
C4
C5,I5
C6
Single port 64 × 10
0
1
450
500
450
378
MHz
Simple dual-port 32 × 20 single
clock
0
1
270
500
450
378
MHz
Simple dual-port 64 × 10 single
clock
0
1
428
500
450
378
MHz
Single-port 256 × 36
0
1
360
400
360
310
MHz
Single-port 256 × 36, with the
read-during-write option set to
Old Data
0
1
250
280
250
210
MHz
Simple dual-port 256 × 36 single
CLK
0
1
360
400
360
310
MHz
Single-port 256 × 36 single CLK,
with the read-during-write option
set to Old Data
0
1
250
280
250
210
MHz
True dual port 512 × 18 single CLK
0
1
360
400
360
310
MHz
True dual-port 512 × 18 single CLK,
with the read-during-write option
set to Old Data
0
1
250
280
250
210
MHz
Min Pulse Width (clock high time)
—
—
900
850
950
1130
ps
Min Pulse Width (clock low time)
—
—
730
690
770
920
ps
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–59
Table 1–49 lists the embedded memory block specifications for Arria II GZ devices.
Table 1–49. Embedded Memory Block Performance Specifications for Arria II GZ Devices (Note 1)
Resources Used
Memory
MLAB
(2)
Mode
Performance
Unit
ALUTs
TriMatrix
Memory
C3
I3
C4
I4
Single port 64 × 10
0
1
500
500
450
450
MHz
Simple dual-port 32 × 20
0
1
500
500
450
450
MHz
Simple dual-port 64 × 10
0
1
500
500
450
450
MHz
ROM 64 × 10
0
1
500
500
450
450
MHz
ROM 32 × 20
0
1
500
500
450
450
MHz
Single-port 256 × 36
0
1
540
540
475
475
MHz
Simple dual-port 256 × 36
0
1
490
490
420
420
MHz
Simple dual-port 256 × 36, with the
read-during-write option set to Old
Data
0
1
340
340
300
300
MHz
0
1
430
430
370
370
MHz
0
1
335
335
290
290
MHz
0
1
540
540
475
475
MHz
True dual port 512 × 18
M9K
True dual-port 512 × 18, with the
Block (2)
read-during-write option set to Old
Data
ROM 1 Port
ROM 2 Port
0
1
540
540
475
475
MHz
Min Pulse Width (clock high time)
—
—
800
800
850
850
ps
Min Pulse Width (clock low time)
—
—
625
625
690
690
ps
Single-port 2K × 72
0
1
440
400
380
350
MHz
Simple dual-port 2K × 72
0
1
435
375
385
325
MHz
Simple dual-port 2K × 72, with the
read-during-write option set to Old
Data
0
1
240
225
205
200
MHz
Simple dual-port 2K × 64 (with ECC)
0
1
300
295
255
250
MHz
True dual-port 4K × 36
0
1
375
350
330
310
MHz
0
1
230
225
205
200
MHz
ROM 1 Port
0
1
500
450
435
420
MHz
ROM 2 Port
0
1
465
425
400
400
MHz
Min Pulse Width (clock high time)
—
—
755
860
860
950
ps
Min Pulse Width (clock low time)
—
—
625
690
690
690
ps
M144K
Block (2) True dual-port 4K × 36, with the
read-during-write option set to Old
Data
Notes to Table 1–48:
(1) To achieve the maximum memory block performance, use a memory block clock that comes through global clock routing from an on-chip PLL
set to 50% output duty cycle. Use the Quartus II software to report timing for this and other memory block clocking schemes.
(2) When you use the error detection CRC feature, there is no degradation in FMAX.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–60
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Configuration
Table 1–50 lists the configuration mode specifications for Arria II GX and GZ devices.
Table 1–50. Configuration Mode Specifications for Arria II Devices
DCLK Frequency
Programming Mode
Unit
Min
Typ
Max
Passive serial
—
—
125
MHz
Fast passive parallel
—
—
125
MHz
Fast active serial (fast clock)
17
26
40
MHz
Fast active serial (slow clock)
8.5
13
20
MHz
Remote update only in fast AS mode
—
—
10
MHz
JTAG Specifications
Table 1–51 lists the JTAG timing parameters and values for Arria II GX and GZ
devices.
Table 1–51. JTAG Timing Parameters and Values for Arria II Devices
Symbol
Description
Min
Max
Unit
tJCP
TCK clock period
30
—
ns
tJCH
TCK clock high time
14
—
ns
tJCL
TCK clock low time
14
—
ns
tJPSU (TDI)
TDI JTAG port setup time
1
—
ns
tJPSU (TMS)
TMS JTAG port setup time
3
—
ns
tJPH
JTAG port hold time
5
—
ns
tJPCO
JTAG port clock to output
—
11
ns
tJPZX
JTAG port high impedance to valid output
—
14
ns
tJPXZ
JTAG port valid output to high impedance
—
14
ns
Chip-Wide Reset (Dev_CLRn) Specifications
Table 1–52 lists the specifications for the chip-wide reset (Dev_CLRn) for Arria II GX
and GZ devices.
Table 1–52. Chip-Wide Reset (Dev_CLRn) Specifications for Arria II Devices
Description
Dev_CLRn
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Min
Typ
Max
Unit
500
—
—
s
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–61
Periphery Performance
This section describes periphery performance, including high-speed I/O, external
memory interface, and IOE programmable delay.
I/O performance supports several system interfaces, for example the high-speed I/O
interface, external memory interface, and the PCI/PCI-X bus interface. I/O using
SSTL-18 Class I termination standard can achieve up to the stated DDR2 SDRAM
interfacing speed with typical DDR2 SDRAM memory interface setup. I/O using
general purpose I/O (GPIO) standards such as 3.0, 2.5, 1.8, or 1.5 LVTTL/LVCMOS
are capable of typical 200 MHz interfacing frequency with 10pF load.
1
Actual achievable frequency depends on design- and system-specific factors. You
should perform HSPICE/IBIS simulations based on your specific design and system
setup to determine the maximum achievable frequency in your system.
High-Speed I/O Specification
Table 1–53 lists the high-speed I/O timing for Arria II GX devices.
Table 1–53. High-Speed I/O Specifications for Arria II GX Devices (Part 1 of 4)
I3
Symbol
C4
C5,I5
C6
Conditions
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Clock
fHSCLK_IN
(input clock
frequency)–Row
I/O
Clock boost
factor, W =
1 to 40 (1)
5
670
5
670
5
622
5
500
MHz
fHSCLK_IN
(input clock
frequency)–
Column I/O
Clock boost
factor, W =
1 to 40 (1)
5
500
5
500
5
472.5
5
472.5
MHz
fHSCLK_OUT
(output clock
frequency)–Row
I/O
—
5
670
5
670
5
622
5
500
MHz
fHSCLK_OUT
(output clock
frequency)–
Column I/O
—
5
500
5
500
5
472.5
5
472.5
MHz
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–62
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–53. High-Speed I/O Specifications for Arria II GX Devices (Part 2 of 4)
I3
Symbol
C4
C5,I5
C6
Conditions
Unit
Min
Max
Min
Max
Min
Max
Min
Max
SERDES factor,
J = 3 to 10
(using
dedicated
SERDES)
150
1250
(2)
150
1250
(2)
150
1050
(2)
150
840
Mbps
SERDES factor,
J = 4 to 10
(using logic
elements as
SERDES)
(3)
945
(3)
945
(3)
840
(3)
740
Mbps
SERDES factor,
J = 2 (using
DDR registers)
and J = 1
(using SDR
register)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
Mbps
SERDES factor,
J = 4 to 10
(3)
945
(3)
945
(3)
840
(3)
740
Mbps
Transmitter
fHSDR_TX (true
LVDS output data
rate)
fHSDR_TX_E3R
(emulated
LVDS_E_3R
output data rate)
(7)
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–63
Table 1–53. High-Speed I/O Specifications for Arria II GX Devices (Part 3 of 4)
I3
Symbol
C4
C5,I5
C6
Conditions
Unit
Min
Max
Min
Max
Min
Max
Min
Max
True LVDS with
dedicated
SERDES
(data rate
600–1,250
Mbps)
—
175
—
175
—
225
—
300
ps
True LVDS with
dedicated
SERDES
(data rate
< 600 Mbps)
—
0.105
—
0.105
—
0.135
—
0.18
UI
True LVDS and
emulated
LVDS_E_3R
with logic
elements as
SERDES (data
rate 600
– 945 Mbps)
—
260
—
260
—
300
—
350
ps
True LVDS and
emulated
LVDS_E_3R
with logic
elements as
SERDES
(data rate
< 600 Mbps)
—
0.16
—
0.16
—
0.18
—
0.21
UI
tTX_DCD
True LVDS and
emulated
LVDS_E_3R
45
55
45
55
45
55
45
55
%
tRISE and tFALL
True LVDS and
emulated
LVDS_E_3R
—
200
—
200
—
225
—
250
ps
True LVDS (5)
—
150
—
150
—
175
—
200
ps
Emulated
LVDS_E_3R
—
200
—
200
—
250
—
300
ps
SERDES factor
J = 3 to 10
150
1250
150
1250
150
1050
150
840
Mbps
tTX_JITTER (4)
TCCS
Receiver (6)
True differential
I/O standards fHSDRDPA (data
rate)
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–64
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–53. High-Speed I/O Specifications for Arria II GX Devices (Part 4 of 4)
I3
Symbol
C4
C5,I5
C6
Conditions
Unit
Min
Max
Min
Max
Min
Max
Min
Max
SERDES factor
J = 3 to 10
(3)
945
(7)
(3)
945
(7)
(3)
740
(7)
(3)
640
(7)
Mbps
SERDES factor
J = 2 (using
DDR registers)
(3)
(7)
(3)
(7)
(3)
(7)
(3)
(7)
Mbps
SERDES factor
J = 1 (using
SDR registers)
(3)
(7)
(3)
(7)
(3)
(7)
(3)
(7)
Mbps
Soft-CDR PPM
tolerance
Soft-CDR
mode
—
300
—
300
—
300
—
300
PPM
DPA run length
DPA mode
—
10,000
—
10,000
—
10,000
—
10,000
UI
Non-DPA mode
(5)
—
300
—
300
—
350
—
400
ps
fHSDR (data rate)
Sampling
window (SW)
Notes to Table 1–53:
(1) fHSCLK_IN = fHSDR / W. Use W to determine the supported selection of input reference clock frequencies for the desired data rate.
(2) Applicable for interfacing with DPA receivers only. For interfacing with non-DPA receivers, you must calculate the leftover timing margin in the
receiver by performing link timing closure analysis. For Arria II GX transmitter to Arria II GX non-DPA receiver, the maximum supported data
rate is 945 Mbps. For data rates above 840 Mbps, perform PCB trace compensation by adjusting the PCB trace length for LVDS channels to
improve channel-to-channel skews.
(3) The minimum and maximum specification depends on the clock source (for example, PLL and clock pin) and the clock routing resource you
use (global, regional, or local). The I/O differential buffer and input register do not have a minimum toggle rate.
(4) The specification is only applicable under the influence of core noise.
(5) Applicable for true LVDS using dedicated SERDES only.
(6) Dedicated SERDES and DPA features are only available on the right banks.
(7) You must calculate the leftover timing margin in the receiver by performing link timing closure analysis. You must consider the board skew
margin, transmitter channel-to-channel skew, and the receiver sampling margin to determine the leftover timing margin.
Table 1–54 lists the high-speed I/O timing for Arria II GZ devices.
Table 1–54. High-Speed I/O Specifications for Arria II GZ Devices (Note 1), (2), (10) (Part 1 of 3)
C3, I3
Symbol
C4, I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
Clock
fHSCLK_in (input clock
frequency) true
differential I/O
standards
Clock boost factor
W = 1 to 40 (3)
5
—
717
5
—
717
MHz
fHSCLK_in (input clock
frequency) single
ended I/O standards
(9)
Clock boost factor
W = 1 to 40 (3)
5
—
717
5
—
717
MHz
fHSCLK_in (input clock
frequency) single
ended I/O standards
(10)
Clock boost factor
W = 1 to 40 (3)
5
—
420
5
—
420
MHz
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–65
Table 1–54. High-Speed I/O Specifications for Arria II GZ Devices (Note 1), (2), (10) (Part 2 of 3)
C3, I3
Symbol
C4, I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
—
5
—
717 (7)
5
—
717 (7)
MHz
SERDES factor, J = 3
to 10
(using dedicated
SERDES) (8)
(4)
—
1250
(4)
—
1250
Mbps
SERDES factor J = 2,
(using DDR registers)
(4)
—
(5)
(4)
—
(5)
Mbps
SERDES factor J = 1,
(uses an SDR
register)
(4)
—
(5)
(4)
—
(5)
Mbps
(4)
—
1152
(4)
—
800
Mbps
(4)
—
200
(4)
—
200
Mbps
Total jitter for data
rate, 600 Mbps to
1.6 Gbps
—
—
160
—
—
160
ps
Total jitter for data
rate, < 600 Mbps
—
—
0.1
—
—
0.1
UI
Total jitter for data
rate, 600 Mbps to
1.25 Gbps
—
—
300
—
—
325
ps
Total jitter for data
rate < 600 Mbps
—
—
0.2
—
—
0.25
UI
—
—
—
0.15
—
—
0.15
UI
TX output clock duty
cycle for both True
and emulated
differential I/O
standards
45
50
55
45
50
55
%
fHSCLK_OUT (output
clock frequency)
Transmitter
fHSDR (true LVDS
output data rate)
fHSDR (emulated
LVDS_E_3R output
data rate) (5)
fHSDR (emulated
LVDS_E_1R output
data rate)
SERDES factor J = 4
to 10
tx Jitter
tx Jitter - emulated
differential I/O
standards with three
external output resistor
network
tx Jitter - emulated
differential I/O
standards with one
external output resistor
network
tDUTY
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–66
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–54. High-Speed I/O Specifications for Arria II GZ Devices (Note 1), (2), (10) (Part 3 of 3)
C3, I3
Symbol
C4, I4
Conditions
Unit
Min
Typ
Max
Min
Typ
Max
True differential I/O
standards
—
—
200
—
—
200
ps
Emulated differential
I/O standards with
three external output
resistor networks
—
—
250
—
—
300
ps
Emulated differential
I/O standards with
one external output
resistor
—
—
500
—
—
500
ps
True LVDS
—
—
100
—
—
100
ps
Emulated
LVDS_E_3R
—
—
250
—
—
250
ps
SERDES factor
J = 3 to 10
150
—
1250
150
—
1250
Mbps
SERDES factor
J = 3 to 10
(4)
—
(6)
(4)
—
(6)
Mbps
SERDES factor J = 2,
uses DDR registers
(4)
—
(5)
(4)
—
(5)
Mbps
SERDES factor J = 1,
uses an SDR register
(4)
—
(5)
(4)
—
(5)
Mbps
DPA run length
DPA mode
—
—
10000
—
—
10000
UI
Soft-CDR PPM
tolerance
Soft-CDR mode
—
—
300
—
—
300
± PPM
Sampling Window
(SW)
Non-DPA mode
—
—
300
—
—
300
ps
tRISE & tFALL
TCCS
Receiver
True differential I/O
standards - fHSDRDPA
(data rate)
fHSDR (data rate)
Notes to Table 1–54:
(1) When J = 3 to 10, use the SERDES block.
(2) When J = 1 or 2, bypass the SERDES block.
(3) Clock Boost Factor (W) is the ratio between input data rate to the input clock rate.
(4) The minimum specification depends on the clock source (for example, the PLL and clock pin) and the clock routing resource (global, regional,
or local) that you use. The I/O differential buffer and input register do not have a minimum toggle rate.
(5) You must calculate the leftover timing margin in the receiver by performing link timing closure analysis. You must consider the board skew
margin, transmitter channel-to-channel skew, and receiver sampling margin to determine leftover timing margin.
(6) You can estimate the achievable maximum data rate for non-DPA mode by performing link timing closure analysis. You must consider the board
skew margin, transmitter delay margin, and the receiver sampling margin to determine the maximum data rate supported.
(7) This is achieved by using the LVDS and DPA clock network.
(8) If the receiver with DPA enabled and transmitter are using shared PLLs, the minimum data rate is 150 Mbps.
(9) This only applies to DPA and soft-CDR modes.
(10) This only applies to LVDS source synchronous mode.
Table 1–55 lists DPA lock time specifications for Arria II GX and GZ devices.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–67
Table 1–55. DPA Lock Time Specifications for Arria II Devices (Note 1), (2), (3)
Training Pattern
Number of Data
Transitions in One
Repetition of the
Training Pattern
Number of
Repetitions per
256 Data
Transitions (4)
Maximum
00000000001111111111
2
128
640 data transitions
00001111
2
128
640 data transitions
10010000
4
64
640 data transitions
10101010
8
32
640 data transitions
01010101
8
32
640 data transitions
Standard
SPI-4
Parallel Rapid I/O
Miscellaneous
Notes to Table 1–55:
(1) The DPA lock time is for one channel.
(2) One data transition is defined as a 0-to-1 or 1-to-0 transition.
(3) The DPA lock time stated in the table applies to both commercial and industrial grade.
(4) This is the number of repetitions for the stated training pattern to achieve the 256 data transitions.
Figure 1–5 shows the LVDS soft-CDR/DPA sinusoidal jitter tolerance specification for
Arria II GZ devices at a data rate less than 1.25 Gbps and all the Arria II GX devices.
Figure 1–5. LVDS Soft-CDR/DPA Sinusoidal Jitter Tolerance Specification for All Arria II GX Devices and for Arria II GZ
Devices at a Data Rate less than 1.25 Gbps
Sinusoidal Jitter Amplitude (UI)
20db/dec
0.1
P-P
Jitter Frequency (Hz)
baud/1667
July 2012
Altera Corporation
20,000,000
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–68
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Figure 1–6 shows the LVDS soft-CDR/DPA sinusoidal jitter tolerance specification for
Arria II GZ devices at 1.25 Gbps data rate.
Figure 1–6. LVDS Soft-CDR/DPA Sinusoidal Jitter Tolerance Specification for Arria II GZ Devices at a 1.25 Gbps Data Rate
Sinusoidal Jitter Amplitude (UI)
25
8.5
0.35
0.1
10,000 (F1) 17,565 (F2)
Jitter Frequency (Hz)
50,000,000 (F4)
1,493,000 (F3)
Table 1–56 lists the LVDS soft-CDR/DPA sinusoidal jitter tolerance specification for
Arria II GZ devices at 1.25 Gbps data rate.
Table 1–56. LVDS Soft-CDR/DPA Sinusoidal Jitter Mask Values for Arria II GZ Devices at
1.25 Gbps Data Rate
Jitter Frequency (Hz)
Sinusoidal Jitter (UI)
F1
10,000
25.000
F2
17,565
25.000
F3
1,493,000
0.350
F4
50,000,000
0.350
External Memory Interface Specifications
f For the maximum clock rate supported for Arria II GX and GZ device family, refer to
the External Memory Interface Spec Estimator page on the Altera website.
Table 1–57 lists the external memory interface specifications for Arria II GX devices.
Table 1–57. External Memory Interface Specifications for Arria II GX Devices (Part 1 of 2)
Frequency Range (MHz)
C6
Resolution
(°)
DQS Delay
Buffer Mode
(1)
Number of
Delay Chains
90-130
90-110
22.5
Low
16
110-180
110-170
110-150
30
Low
12
2
140-220
140-210
140-180
36
Low
10
3
170-270
170-260
170-220
45
Low
8
4
220-340
220-310
220-270
30
High
12
Frequency
Mode
C4
I3, C5, I5
0
90-140
1
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–69
Table 1–57. External Memory Interface Specifications for Arria II GX Devices (Part 2 of 2)
Frequency Range (MHz)
C6
Resolution
(°)
DQS Delay
Buffer Mode
(1)
Number of
Delay Chains
270-380
270-320
36
High
10
320-410
320-370
45
High
8
Frequency
Mode
C4
I3, C5, I5
5
270-410
6
320-450
Note to Table 1–57:
(1) Low indicates a 6-bit DQS delay setting; high indicates a 5-bit DQS delay setting.
Table 1–58 lists the DLL frequency range specifications for Arria II GZ devices.
Table 1–58. DLL Frequency Range Specifications for Arria II GZ Devices
Frequency Range (MHz)
Frequency Mode
Available Phase Shift
DQS Delay
Buffer Mode
(1)
Number of
Delay
Chains
–3
–4
0
90-130
90-120
22.5°, 45°, 67.5°, 90°
Low
16
1
120-170
120-160
30°, 60°, 90°, 120°
Low
12
2
150-210
150-200
36°, 72°, 108°, 144°
Low
10
3
180-260
180-240
45°, 90°,135°, 180°
Low
8
4
240-320
240-290
30°, 60°, 90°, 120°
High
12
5
290-380
290-360
36°, 72°, 108°, 144°
High
10
6
360-450
360-450
45°, 90°, 135°, 180°
High
8
7
470-630
470-590
60°, 120°, 180°, 240°
High
6
Note to Table 1–58:
(1) Low indicates a 6-bit DQS delay setting; high indicates a 5-bit DQS delay setting.
Table 1–59 lists the DQS phase offset delay per stage for Arria II GX devices.
Table 1–59. DQS Phase Offset Delay Per Setting for Arria II GX Devices (Note 1), (2), (3)
Speed Grade
Min
Max
Unit
C4
7.0
13.0
ps
I3, C5, I5
7.0
15.0
ps
C6
8.5
18.0
ps
Notes to Table 1–59:
(1) The valid settings for phase offset are -64 to +63 for frequency modes 0 to 3 and -32 to +31 for frequency modes
4 to 5.
(2) The typical value equals the average of the minimum and maximum values.
(3) The delay settings are linear.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–70
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–60 lists the DQS phase shift error for Arria II GX devices.
Table 1–60. DQS Phase Shift Error Specification for DLL-Delayed Clock (tDQS_PSERR) for Arria II GX
Devices (Note 1)
Number of DQS Delay Buffer
C4
I3, C5, I5
C6
Unit
1
26
30
36
ps
2
52
60
72
ps
3
78
90
108
ps
4
104
120
144
ps
Note to Table 1–60:
(1) This error specification is the absolute maximum and minimum error. For example, skew on three DQS delay
buffers in a C4 speed grade is ± 78 ps or ± 39 ps.
Table 1–61 lists the DQS phase shift error for Arria II GZ devices.
Table 1–61. DQS Phase Shift Error Specification for DLL-Delayed Clock (tDQS_PSERR) for Arria II GZ
Devices (Note 1)
Number of DQS Delay Buffer
–3
–4
Unit
1
28
30
ps
2
56
60
ps
3
84
90
ps
4
112
120
ps
Note to Table 1–61:
(1) This error specification is the absolute maximum and minimum error. For example, skew on three DQS delay
buffers in a 3 speed grade is ± 84 ps or ± 42 ps.
Table 1–62 lists the memory output clock jitter specifications for Arria II GX devices.
Table 1–62. Memory Output Clock Jitter Specification for Arria II GX Devices (Note 1), (2), (3)
–4
Clock
Network
Symbol
Clock period jitter
Global
Cycle-to-cycle period
jitter
Duty cycle jitter
Parameter
–5
–6
Unit
Min
Max
Min
Max
Min
Max
tJIT(per)
-100
100
-125
125
-125
125
ps
Global
tJIT(cc)
-200
200
-250
250
-250
250
ps
Global
tJIT(duty)
-100
100
-125
125
-125
125
ps
Notes to Table 1–62:
(1) The memory output clock jitter measurements are for 200 consecutive clock cycles, as specified in the JEDEC DDR2/DDR3 SDRAM standard.
(2) The clock jitter specification applies to memory output clock pins generated using DDIO circuits clocked by a PLL output routed on a global
clock network.
(3) The memory output clock jitter stated in Table 1–62 is applicable when an input jitter of 30 ps is applied.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
1–71
Table 1–63 lists the memory output clock jitter specifications for Arria II GZ devices.
Table 1–63. Memory Output Clock Jitter Specification for Arria II GZ Devices (Note 1), (2), (3)
–3
Clock
Network
Symbol
Clock period jitter
Regional
Cycle-to-cycle period jitter
Duty cycle jitter
Parameter
–4
Unit
Min
Max
Min
Max
tJIT(per)
-55
55
-55
55
ps
Regional
tJIT(cc)
-110
110
-110
110
ps
Regional
tJIT(duty)
-82.5
82.5
-82.5
82.5
ps
Clock period jitter
Global
tJIT(per)
-82.5
82.5
-82.5
82.5
ps
Cycle-to-cycle period jitter
Global
tJIT(cc)
-165
165
-165
165
ps
Duty cycle jitter
Global
tJIT(duty)
-90
90
-90
90
ps
Notes to Table 1–63:
(1) The memory output clock jitter measurements are for 200 consecutive clock cycles, as specified in the JEDEC DDR2/DDR3 SDRAM standard.
(2) The clock jitter specification applies to memory output clock pins generated using differential signal-splitter and DDIO circuits clocked by a
PLL output routed on a regional or global clock network as specified. Altera recommends using regional clock networks whenever possible.
(3) The memory output clock jitter stated in Table 1–63 is applicable when an input jitter of 30 ps is applied.
Duty Cycle Distortion (DCD) Specifications
Table 1–64 lists the worst-case DCD specifications for Arria II GX devices.
Table 1–64. Duty Cycle Distortion on I/O Pins for Arria II GX Devices (Note 1)
C4
I3, C5, I5
C6
Symbol
Output Duty Cycle
Unit
Min
Max
Min
Max
Min
Max
45
55
45
55
45
55
%
Note to Table 1–64:
(1) The DCD specification applies to clock outputs from the PLL, global clock tree, IOE driving dedicated, and general
purpose I/O pins.
Table 1–65 lists the worst-case DCD specifications for Arria II GZ devices.
Table 1–65. Duty Cycle Distortion on I/O Pins for Arria II GZ Devices (Note 1)
C3, I3
C4, I4
Symbol
Output Duty Cycle
Unit
Min
Max
Min
Max
45
55
45
55
%
Note to Table 1–65:
(1) The DCD specification applies to clock outputs from the PLL, global clock tree, IOE driving dedicated, and general
purpose I/O pins.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–72
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
IOE Programmable Delay
Table 1–66 lists the delay associated with each supported IOE programmable delay
chain for Arria II GX devices.
Table 1–66. IOE Programmable Delay for Arria II GX Devices
Maximum Offset
Parameter
Available
Settings
(1)
Minimum
Offset
(2)
Fast Model
Slow Model
Unit
I3
C4
I5
I3
C4
C5
I5
C6
Output
enable pin
delay
7
0
0.413
0.442
0.413
0.814
0.713
0.796
0.801
0.873
ns
Delay from
output
register to
output pin
7
0
0.339
0.362
0.339
0.671
0.585
0.654
0.661
0.722
ns
Input delay
from pin to
internal cell
52
0
1.494
1.607
1.494
2.895
2.520
2.733
2.775
2.944
ns
Input delay
from pin to
input register
52
0
1.493
1.607
1.493
2.896
2.503
2.732
2.774
2.944
ns
DQS bus to
input register
delay
4
0
0.074
0.076
0.074
0.140
0.124
0.147
0.147
0.167
ns
Notes to Table 1–66:
(1) The available setting for every delay chain starts with zero and ends with the specified maximum number of settings.
(2) The minimum offset represented in the table does not include intrinsic delay.
Table 1–67 lists the IOE programmable delay settings for Arria II GZ devices.
Table 1–67. IOE Programmable Delay for Arria II GZ Devices
Maximum Offset
Parameter
Available
Settings
(1)
Minimum
Offset (2)
Fast Model
Slow Model
Unit
Industrial
Commercial
C3
I3
C4
I4
D1
15
0
0.462
0.505
0.795
0.801
0.857
0.864
ns
D2
7
0
0.234
0.232
0.372
0.371
0.407
0.405
ns
D3
7
0
1.700
1.769
2.927
2.948
3.157
3.178
ns
D4
15
0
0.508
0.554
0.882
0.889
0.952
0.959
ns
D5
15
0
0.472
0.500
0.799
0.817
0.875
0.882
ns
D6
6
0
0.186
0.195
0.319
0.321
0.345
0.347
ns
Notes to Table 1–67:
(1) You can set this value in the Quartus II software by selecting D1, D2, D3, D4, D5, and D6 in the Assignment Name column.
(2) Minimum offset does not include the intrinsic delay.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
I/O Timing
1–73
I/O Timing
Altera offers two ways to determine I/O timing:
■
Using the Microsoft Excel-based I/O Timing.
■
Using the Quartus II Timing Analyzer.
The Microsoft Excel-based I/O Timing provides pin timing performance for each
device density and speed grade. The data is typically used prior to designing the
FPGA to get an estimate of the timing budget as part of the link timing analysis. The
Quartus II timing analyzer provides a more accurate and precise I/O timing data
based on the specifics of the design after place-and-route is complete.
f The Microsoft Excel-based I/O Timing spreadsheet is downloadable from the
Literature: Arria II Devices web page.
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–74
Chapter 1: Device Datasheet for Arria II Devices
Glossary
Glossary
Table 1–68 lists the glossary for this chapter.
Table 1–68. Glossary (Part 1 of 4)
Letter
Subject
Definitions
Receiver Input Waveforms
Single-Ended Waveform
Positive Channel (p) = VIH
VID
Negative Channel (n) = VIL
VCM
Ground
Differential Waveform
VID
p−n=0V
VID
A,
B,
C,
Differential I/O
Standards
Transmitter Output Waveforms
D
Single-Ended Waveform
Positive Channel (p) = VOH
VOD
Negative Channel (n) = VOL
VCM
Ground
Differential Waveform
VOD
p−n=0V
VOD
E,
fHSCLK
Left/Right PLL input clock frequency.
fHSDR
High-speed I/O block: Maximum/minimum LVDS data transfer rate
(fHSDR = 1/TUI), non-DPA.
fHSDRDPA
High-speed I/O block: Maximum/minimum LVDS data transfer rate
(fHSDRDPA = 1/TUI), DPA.
F
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Glossary
1–75
Table 1–68. Glossary (Part 2 of 4)
Letter
Subject
J
Definitions
High-speed I/O block: Deserialization factor (width of parallel data bus).
JTAG Timing Specifications:
TMS
G,
TDI
H,
I,
t JCP
JTAG Timing
Specifications
t JCH
J
t JCL
t JPH
t JPSU
TCK
tJPZX
t JPXZ
t JPCO
TDO
PLL Specification parameters:
Diagram of PLL Specifications (1)
CLKOUT Pins
Switchover
f OUT_EXT
K,
CLK
L,
f IN
N
f INPFD
PFD
M,
N,
CP
Core Clock
PLL
Specifications
LF
VCO
K
(2)
fVCO /K
Counters
C0..C9
f OUT
GCLK
RCLK
O,
M
P
Key
Reconfigurable in User Mode
External Feedback
Notes:
(1) CoreClock can only be fed by dedicated clock input pins or PLL outputs.
(2) This is the VCO post-scale counter K.
Q,
R
July 2012
RL
Altera Corporation
Receiver differential input discrete resistor (external to the Arria II device).
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–76
Chapter 1: Device Datasheet for Arria II Devices
Glossary
Table 1–68. Glossary (Part 3 of 4)
Letter
Subject
Definitions
The period of time during which the data must be valid in order to capture it correctly. The setup
and hold times determine the ideal strobe position within the sampling window:
Timing Diagram
SW (sampling
window)
Bit Time
0.5 x TCCS
RSKM
Sampling Window
(SW)
RSKM
0.5 x TCCS
The JEDEC standard for SSTL and HSTL I/O standards define both the AC and DC input signal
values. The AC values indicate the voltage levels at which the receiver must meet its timing
specifications. The DC values indicate the voltage levels at which the final logic state of the
receiver is unambiguously defined. After the receiver input has crossed the AC value, the receiver
changes to the new logic state.
The new logic state is then maintained as long as the input stays beyond the AC threshold. This
approach is intended to provide predictable receiver timing in the presence of input waveform
ringing:
S
Single-Ended Voltage Referenced I/O Standard
Single-ended
Voltage
Referenced I/O
Standard
VCCIO
VOH
VIH (AC )
VIH(DC)
VREF
VIL(DC)
VIL(AC )
VOL
VSS
tC
High-speed receiver and transmitter input and output clock period.
TCCS
(channel-tochannelskew)
The timing difference between the fastest and slowest output edges, including tCO variation and
clock skew, across channels driven by the same PLL. The clock is included in the TCCS
measurement (refer to the Timing Diagram figure under S in this table).
High-speed I/O block: Duty cycle on the high-speed transmitter output clock.
T
tDUTY
Timing Unit Interval (TUI)
The timing budget allowed for skew, propagation delays, and data sampling window.
(TUI = 1/(Receiver Input Clock Frequency Multiplication Factor) = tC/w)
tFALL
Signal high-to-low transition time (80-20%)
tINCCJ
Cycle-to-cycle jitter tolerance on the PLL clock input.
tOUTPJ_IO
Period jitter on the general purpose I/O driven by a PLL.
tOUTPJ_DC
Period jitter on the dedicated clock output driven by a PLL.
tRISE
Signal low-to-high transition time (20-80%).
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Chapter 1: Device Datasheet for Arria II Devices
Document Revision History
1–77
Table 1–68. Glossary (Part 4 of 4)
Letter
Subject
U,
V
Definitions
VCM(DC)
DC common mode input voltage.
VICM
Input common mode voltage: The common mode of the differential signal at the receiver.
VID
Input differential voltage swing: The difference in voltage between the positive and
complementary conductors of a differential transmission at the receiver.
VDIF(AC)
AC differential input voltage: Minimum AC input differential voltage required for switching.
VDIF(DC)
DC differential input voltage: Minimum DC input differential voltage required for switching.
VIH
Voltage input high: The minimum positive voltage applied to the input which is accepted by the
device as a logic high.
VIH(AC)
High-level AC input voltage.
VIH(DC)
High-level DC input voltage.
VIL
Voltage input low: The maximum positive voltage applied to the input which is accepted by the
device as a logic low.
VIL(AC)
Low-level AC input voltage.
VIL(DC)
Low-level DC input voltage.
VOCM
Output common mode voltage: The common mode of the differential signal at the transmitter.
VOD
Output differential voltage swing: The difference in voltage between the positive and
complementary conductors of a differential transmission at the transmitter.
W
High-speed I/O block: The clock boost factor.
W,
X,
Y,
Z
Document Revision History
Table 1–69 lists the revision history for this chapter.
Table 1–69. Document Revision History (Part 1 of 2)
Date
July 2012
December 2011
June 2011
July 2012
Version
4.3
Changes
■
Updated the VCCH_GXBL/R operating conditions in Table 1–6.
■
Finalized Arria II GZ information in Table 1–20.
■
Added BLVDS specification in Table 1–32 and Table 1–33.
■
Updated input and output waveforms in Table 1–68.
■
Updated Table 1–32, Table 1–33, Table 1–34, Table 1–35, Table 1–40, Table 1–41,
Table 1–54, and Table 1–67.
■
Minor text edits.
■
Added Table 1–60.
■
Updated Table 1–32, Table 1–33, Table 1–38, Table 1–41, and Table 1–61.
■
Updated the “Switching Characteristics” section introduction.
■
Minor text edits.
4.2
4.1
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
1–78
Chapter 1: Device Datasheet for Arria II Devices
Document Revision History
Table 1–69. Document Revision History (Part 2 of 2)
Date
December 2010
July 2010
Version
Changes
■
Added Arria II GZ information.
■
Added Table 1–61 with Arria II GX information.
■
Updated Table 1–1, Table 1–2, Table 1–5, Table 1–6, Table 1–7, Table 1–11, Table 1–35,
Table 1–37, Table 1–40, Table 1–42, Table 1–44, Table 1–45, Table 1–57, Table 1–61, and
Table 1–63.
■
Updated Figure 1–5.
■
Updated for the Quartus II version 10.0 release.
■
Updated the first paragraph for searchability.
■
Minor text edits.
■
Updated Table 1–1, Table 1–4, Table 1–16, Table 1–19, Table 1–21, Table 1–23,
Table 1–25, Table 1–26, Table 1–30, and Table 1–35
■
Added Table 1–27 and Table 1–29.
■
Added I3 speed grade information to Table 1–19, Table 1–21, Table 1–22, Table 1–24,
Table 1–25, Table 1–30, Table 1–32, Table 1–33, Table 1–34, and Table 1–35.
■
Updated the “Operating Conditions” section.
■
Removed “Preliminary” from Table 1–19, Table 1–21, Table 1–22, Table 1–23,
Table 1–24, Table 1–25, Table 1–26, Table 1–28, Table 1–30, Table 1–32, Table 1–33,
Table 1–34, and Figure 1–4.
■
Minor text edits.
4.0
3.0
Updated for the Quartus II version 9.1 SP2 release:
March 2010
February 2010
■
Updated Table 1–3, Table 1–7, Table 1–19, Table 1–21, Table 1–22, Table 1–24,
Table 1–25 and Table 1–33.
■
Updated “Recommended Operating Conditions” section.
■
Minor text edits.
2.3
2.2
Updated Table 1–19.
Updated for Arria II GX v9.1 SP1 release:
February 2010
2.1
■
Updated Table 1–19, Table 1–23, Table 1–28, Table 1–30, and Table 1–33.
■
Added Figure 1–5.
■
Minor text edits.
Updated for Arria II GX v9.1 release:
November 2009
June 2009
2.0
1.2
■
Updated Table 1–1, Table 1–4, Table 1–13, Table 1–14, Table 1–19, Table 1–15,
Table 1–22, Table 1–24, and Table 1–28.
■
Added Table 1–6 and Table 1–33.
■
Added “Bus Hold” on page 1–5.
■
Added “IOE Programmable Delay” section.
■
Minor text edit.
■
Updated Table 1–1, Table 1–3, Table 1–7, Table 1–8, Table 1–18, Table 1–23, Table 1–25,
Table 1–26, Table 1–29, Table 1–30, Table 1–31, Table 1–32, and Table 1–33.
■
Added Table 1–32.
■
Updated Equation 1–1.
March 2009
1.1
Added “I/O Timing” section.
February 2009
1.0
Initial release.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
2. Addendum for the Arria II Device
Handbook
December 2010
AIIGX53002-2.0
AIIGX53002-2.0
This chapter describes changes to the published version of the Arria II Device
Handbook. All changes from Revision 1.1 of this chapter are now incorporated in the
main handbook chapters.
Highlights
f This information is now located in the Overview for the Arria II Device Family chapter.
High-Speed LVDS I/O with DPA and Soft CDR
f This information is now located in the Overview for the Arria II Device Family chapter.
Auto-Calibrating External Memory Interfaces
f This information is now located in the Overview for the Arria II Device Family chapter.
Connecting a Serial Configuration Device to an Arria II Device Family
on AS Interface
f This information is now located in the Configuration, Design Security, and Remote
System Upgrades in Arria II Devices chapter.
Document Revision History
Table 2–1 lists the revision history for this chapter.
Table 2–1. Document Revision History
Date
December 2010
Version
2.0
Changes
■
Updated chapter titles.
■
Moved the “Highlights”, “High-Speed LVDS I/O with DPA and Soft CDR”, and
“Auto-Calibrating External Memory Interfaces” sections to the
Arria II GX Device Family Overview chapter.
■
Moved the “Guidelines for Connecting Serial Configuration Device to Arria II GX
Device Family on AS Interface” section to the Configuration, Design Security, and
Remote System Upgrades in Arria II GX Devices chapter
July 2010
1.2
March 2010
1.1
Added “Guidelines for Connecting Serial Configuration Device to Arria II GX Device
Family on AS Interface”
February 2010
1.0
Initial release.
© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
December 2010
Subscribe
2–2
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Chapter 2: Addendum for the Arria II Device Handbook
Document Revision History
December 2010 Altera Corporation
Additional Information
This chapter provides additional information about the Arria II Device Handbook
and Altera.
About this Handbook
This handbook provides comprehensive information about the Altera® Arria II GX
family of devices.
How to Contact Altera
To locate the most up-to-date information about Altera products, refer to the
following table.
Contact (1)
Technical support
Technical training
Product literature
Contact Method
Address
Website
www.altera.com/support
Website
www.altera.com/training
Email
[email protected]
Website
www.altera.com/literature
Non-technical support (General)
Email
[email protected]
(Software Licensing)
Email
[email protected]
Note to Table:
(1) You can also contact your local Altera sales office or sales representative.
Typographic Conventions
The following table shows the typographic conventions this document uses.
Visual Cue
Meaning
Bold Type with Initial Capital
Letters
Indicate command names, dialog box titles, dialog box options, and other GUI
labels. For example, Save As dialog box. For GUI elements, capitalization matches
the GUI.
bold type
Indicates directory names, project names, disk drive names, file names, file name
extensions, software utility names, and GUI labels. For example, \qdesigns
directory, D: drive, and chiptrip.gdf file.
Italic Type with Initial Capital Letters
Indicate document titles. For example, Stratix IV Design Guidelines.
Indicates variables. For example, n + 1.
italic type
Variable names are enclosed in angle brackets (< >). For example, <file name> and
<project name>.pof file.
Initial Capital Letters
Indicate keyboard keys and menu names. For example, the Delete key and the
Options menu.
“Subheading Title”
Quotation marks indicate references to sections within a document and titles of
Quartus II Help topics. For example, “Typographic Conventions.”
July 2012
Altera Corporation
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
Info–2
Additional Information
Typographic Conventions
Visual Cue
Meaning
Indicates signal, port, register, bit, block, and primitive names. For example, data1,
tdi, and input. The suffix n denotes an active-low signal. For example, resetn.
Courier type
Indicates command line commands and anything that must be typed exactly as it
appears. For example, c:\qdesigns\tutorial\chiptrip.gdf.
Also indicates sections of an actual file, such as a Report File, references to parts of
files (for example, the AHDL keyword SUBDESIGN), and logic function names (for
example, TRI).
r
An angled arrow instructs you to press the Enter key.
1., 2., 3., and
a., b., c., and so on
Numbered steps indicate a list of items when the sequence of the items is important,
such as the steps listed in a procedure.
■ ■
Bullets indicate a list of items when the sequence of the items is not important.
■
1
The hand points to information that requires special attention.
h
A question mark directs you to a software help system with related information.
f
The feet direct you to another document or website with related information.
c
A caution calls attention to a condition or possible situation that can damage or
destroy the product or your work.
w
A warning calls attention to a condition or possible situation that can cause you
injury.
The envelope links to the Email Subscription Management Center page of the Altera
website, where you can sign up to receive update notifications for Altera documents.
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
July 2012 Altera Corporation
Similar pages